SR103AM Dual Channel Safety Monitoring Relay Data Sheet Datasheet En 201408 J52I E 01
2016-05-24
: Pdf Sr103Am Datasheet En 201408 J52I-E-01 SR103AM_datasheet_en_201408_J52I-E-01 Spec Sheets Omron
Open the PDF directly: View PDF 
.
Page Count: 6
| Download | |
| Open PDF In Browser | View PDF |
Safety Monitoring Relays SR103AM Dual-Channel Safety Monitoring Relay • Power requirements—the SR103AM will accept 24 VAC/DC or 115 VAC • Inputs—the SR103AM will accept single or dual N/C inputs or dual inputs from a light curtain • Outputs—the SR103AM has 3 N/O outputs to route power to the coils of power contactors, plus 1 N/C auxiliary output for signaling purposes • External Device Monitoring (EDM) is provided with a N/C loop between S11/S12 and S21 on the SR103AM • Monitored manual or automatic/manual reset modes are available on the SR103AM. Monitored manual reset requires closure of the reset circuit followed by opening of the circuit. Reset occurs when circuit is opened. Auto reset requires only closure of the reset circuit as reset occurs when circuit is closed. Specifications Electrical Power Supply: Power Consumption: Safety Inputs: Max Input Resistance: Outputs: Output Rating AC: Output Rating DC: Min Switched Current/Voltage: Impulse Withstand Voltage: Max Drop-Out Time: Max Output Fuse: Reset Mode: Contactor Monitoring: Mechanical Mounting: Case Material: Max Wire Size: Weight: Color: External Switches: Indication: Mechanical Life: Environmental Enclosure Protection: Operating Temperature: R C All Models SR103AM01 SR103AM02 ±10%, 50-60 Hz 24 VAC/DC 115 VAC Approx. 1 VA 1 N/C or 2 N/C or 2 solid state (light curtain) 800 Ohms per channel 3 N/O + 1 N/C auxiliary Inductive AC-15, 3 A/230 VAC Inductive DC-13, 2 A/24 V 10 mA/10 V 2500 V 12 ms (75 ms by removing supply voltage) 6 A quick-acting or 4 A slow-acting Monitored manual (S11-S21) or automatic/manual (S12-S21) N/C loop S11/S12-S21 US Conforms to EN60439-1, EN60947-1/5/7, EN61000-6, EN62061, EN ISO 13849-1 UL and C-UL listed TÜV Rheinland approved 35 mm (1.38 in.) DIN rail Fiber-filled Polyamide PA6.6 1 x 2.5 mm 2 (14 AWG) stranded 230 g (8.1 oz.) Red None Green = K1 Closed, Green = K2 Closed 1 x 10 7 operations IP20 terminals, IP40 (NEMA 1) housing 24 VAC/DC: -15 to 40°C (5 to 104°F) 115 VAC: -15 to 40°C (5 to 104°F) -25° to 70°C (-13 to 158°F) 93% RH at 104°C (219°F) Storage Temperature: Humidity: Compliance Standards: EN60439-1, EN60947-1/5/7, EN61000-6, EN62061, EN ISO 13849-1 Approvals/Listings: CE marked for all applicable directives, UL and C-UL, TÜV Rheinland Specifications are subject to change without notice. Note: The safety contacts of the STI switches are described as normally closed (N/C)—i.e., with the guard closed, actuator in place, and the machine able to be started. www.omron247.com 1 SR103AM Safety Monitoring Relays Application Output Contact Arrangements Terminal Pin Assignments 14 S12 A1 13 24 S13 S11 23 34 S10 S14 33 42 A2 S21 41 SR103AM Terminal Connections 13 A1 23 33 S13 SAFETY OUTPUT 1 N/O SUPPLY A2 41 S11 SAFETY OUTPUT 2 N/O INPUT #1 N/C S21 SAFETY OUTPUT 3 N/O INPUT #2 N/C S10 S12 14 EDM AND RESET AUXILIARY SIGNALING N/C S12 34 24 42 24VAC/DC, 110VAC K1 (AUX) START MOMENTARY PUSH BUTTON EB SERIES LATCHING E-STOP BUTTON GUARD CLOSED A1 11 12 21 22 33 S11 S21 L1 L2 L3 K2 (AUX) STOP MOMENTARY PUSH BUTTON S12 S14 13 RESET 23 33 41 K1 Relay control and fault monitoring Power supply (S11 = 24 V) + K2 K2 34 MOMENTARY PUSH BUTTON CONTACT PROTECTION E.G. THERMAL CUT OUT + K1 T5009 INTERLOCK SWITCH SR103AM A2 S10 S13 14 24 FUSE FUSE K1 2 www.omron247.com 34 K2 42 M SR103AM Safety Monitoring Relays Application (continued) MS4600 Connected to SR103AM (MPCE monitoring disabled) OSSD1 - Start MS4600 Receiver Power Supply 24 VDC + MS4600 Transmitter OSSD2 A1 S11 S21 SR103AM A2 S10 S13 MCPE Input to 0 V MCPE off www.omron247.com S12 S14 MPCE Monitoring “Disabled” The start switch shown connected between S11 and S21 provides a monitored manual start function. Switch must be closed and then opened to activate a start. For auto-start, connect a wire between S21 and S12 and no connection between S11 and S21. If the MPCE function is not being used on the MS4600 light curtain, the function must be “disabled”, and the MPCE input wire must be connected to 0 V (GND). MPCE Monitoring “Enabled” When using an SR103AM with an MS4600 light curtain, MPCE monitoring may be performed through the safety monitoring relay using terminals S12, S21. This method of MPCE monitoring only allows for Auto Restart/Manual Restart Mode of the safety monitoring relay. If Monitored Manual Restart Mode with MPCE Monitoring is desired, the MPCE Monitoring must be enabled and performed through the MS4600 light curtain. Place wire jumper between terminals S12, S21of the safety monitoring relay. Configure the MS4600 for Start/Restart Interlock Mode. The Monitored Manual Reset is now controlled through the MS4600 light curtain. (See MS4600 Manual for configuration and wiring details of MS4600 light curtain.) 3 SR103AM Safety Monitoring Relays Block Diagram A1 S11 S21 A2 A2 L1 S10 33 41 14 24 34 42 K1 + DC +U B 0V AC 23 + Pin assignment A1 13 Relay control and fault monitoring Power supply (S11=24V) UB S14 S12 K2 N S13 Dimensions (mm/in.) SR103AM 114 4.5 22.5 0.885 99 3.9 35 DIN RAIL MOUNTING 1.38 Ordering Model 4 Supply Inputs Outputs Auxiliary Part No. SR103AM01 24 VAC/DC 2 N/C 3 N/O 1 N/C 44510-1031 SR103AM02 115 VAC 2 N/C 3 N/O 1 N/C 44510-1032 www.omron247.com Terms and Conditions of Sale 1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed part of all quotes, agreements, purchase orders, acknowledgments, price lists, catalogs, manuals, brochures and other documents, whether electronic or in writing, relating to the sale of products or services (collectively, the "Products") by Omron Electronics LLC and its subsidiary companies (“Omron”). Omron objects to any terms or conditions proposed in Buyer’s purchase order or other documents which are inconsistent with, or in addition to, these Terms. 2. Prices; Payment Terms. All prices stated are current, subject to change without notice by Omron. Omron reserves the right to increase or decrease prices on any unshipped portions of outstanding orders. Payments for Products are due net 30 days unless otherwise stated in the invoice. 3. Discounts. Cash discounts, if any, will apply only on the net amount of invoices sent to Buyer after deducting transportation charges, taxes and duties, and will be allowed only if (i) the invoice is paid according to Omron’s payment terms and (ii) Buyer has no past due amounts. 4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month or the maximum legal rate, whichever is less, on any balance not paid within the stated terms. 5. Orders. Omron will accept no order less than $200 net billing. 6. Governmental Approvals. Buyer shall be responsible for, and shall bear all costs involved in, obtaining any government approvals required for the importation or sale of the Products. 7. Taxes. All taxes, duties and other governmental charges (other than general real property and income taxes), including any interest or penalties thereon, imposed directly or indirectly on Omron or required to be collected directly or indirectly by Omron for the manufacture, production, sale, delivery, importation, consumption or use of the Products sold hereunder (including customs duties and sales, excise, use, turnover and license taxes) shall be charged to and remitted by Buyer to Omron. 8. Financial. If the financial position of Buyer at any time becomes unsatisfactory to Omron, Omron reserves the right to stop shipments or require satisfactory security or payment in advance. If Buyer fails to make payment or otherwise comply with these Terms or any related agreement, Omron may (without liability and in addition to other remedies) cancel any unshipped portion of Products sold hereunder and stop any Products in transit until Buyer pays all amounts, including amounts payable hereunder, whether or not then due, which are owing to it by Buyer. Buyer shall in any event remain liable for all unpaid accounts. 9. Cancellation; Etc. Orders are not subject to rescheduling or cancellation unless Buyer indemnifies Omron against all related costs or expenses. 10. Force Majeure. Omron shall not be liable for any delay or failure in delivery resulting from causes beyond its control, including earthquakes, fires, floods, strikes or other labor disputes, shortage of labor or materials, accidents to machinery, acts of sabotage, riots, delay in or lack of transportation or the requirements of any government authority. 11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron: a. Shipments shall be by a carrier selected by Omron; Omron will not drop ship except in “break down” situations. b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall constitute delivery to Buyer; c. All sales and shipments of Products shall be FOB shipping point (unless otherwise stated in writing by Omron), at which point title and risk of loss shall pass from Omron to Buyer; provided that Omron shall retain a security interest in the Products until the full purchase price is paid; d. Delivery and shipping dates are estimates only; and e. Omron will package Products as it deems proper for protection against normal handling and extra charges apply to special conditions. 12. Claims. Any claim by Buyer against Omron for shortage or damage to the Products occurring before delivery to the carrier must be presented in writing to Omron within 30 days of receipt of shipment and include the original transportation bill signed by the carrier noting that the carrier received the Products from Omron in the condition claimed. 13. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL- 14. 15. 16. 17. 18. ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron247.com or contact your Omron representative for published information. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Indemnities. Buyer shall indemnify and hold harmless Omron Companies and their employees from and against all liabilities, losses, claims, costs and expenses (including attorney's fees and expenses) related to any claim, investigation, litigation or proceeding (whether or not Omron is a party) which arises or is alleged to arise from Buyer's acts or omissions under these Terms or in any way with respect to the Products. Without limiting the foregoing, Buyer (at its own expense) shall indemnify and hold harmless Omron and defend or settle any action brought against such Companies to the extent based on a claim that any Product made to Buyer specifications infringed intellectual property rights of another party. Property; Confidentiality. Any intellectual property in the Products is the exclusive property of Omron Companies and Buyer shall not attempt to duplicate it in any way without the written permission of Omron. Notwithstanding any charges to Buyer for engineering or tooling, all engineering and tooling shall remain the exclusive property of Omron. All information and materials supplied by Omron to Buyer relating to the Products are confidential and proprietary, and Buyer shall limit distribution thereof to its trusted employees and strictly prevent disclosure to any third party. Export Controls. Buyer shall comply with all applicable laws, regulations and licenses regarding (i) export of products or information; (iii) sale of products to “forbidden” or other proscribed persons; and (ii) disclosure to non-citizens of regulated technology or information. Miscellaneous. (a) Waiver. No failure or delay by Omron in exercising any right and no course of dealing between Buyer and Omron shall operate as a waiver of rights by Omron. (b) Assignment. Buyer may not assign its rights hereunder without Omron's written consent. (c) Law. These Terms are governed by the law of the jurisdiction of the home office of the Omron company from which Buyer is purchasing the Products (without regard to conflict of law principles). (d) Amendment. These Terms constitute the entire agreement between Buyer and Omron relating to the Products, and no provision may be changed or waived unless in writing signed by the parties. (e) Severability. If any provision hereof is rendered ineffective or invalid, such provision shall not invalidate any other provision. (f) Setoff. Buyer shall have no right to set off any amounts against the amount owing in respect of this invoice. (g) Definitions. As used herein, “including” means “including without limitation”; and “Omron Companies” (or similar words) mean Omron Corporation and any direct or indirect subsidiary or affiliate thereof. Certain Precautions on Specifications and Use 1. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases but the following is a non-exhaustive list of applications for which particular attention must be given: (i) Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this document. (ii) Use in consumer products or any use in significant quantities. (iii) Energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. (iv) Systems, machines and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to this Product. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO 2. 3. 4. 5. ADDRESS THE RISKS, AND THAT THE OMRON’S PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. OMRON AUTOMATION AND SAFETY • THE AMERICAS HEADQUARTERS • Chicago, IL USA • 847.843.7900 • 800.556.6766 • www.omron247.com OMRON CANADA, INC. • HEAD OFFICE Toronto, ON, Canada • 416.286.6465 • 866.986.6766 • www.omron247.com OMRON ARGENTINA • SALES OFFICE Cono Sur • 54.11.4783.5300 OMRON ELECTRONICS DE MEXICO • HEAD OFFICE México DF • 52.55.59.01.43.00 • 01-800-226-6766 • mela@omron.com OMRON CHILE • SALES OFFICE Santiago • 56.9.9917.3920 OMRON ELECTRONICS DE MEXICO • SALES OFFICE Apodaca, N.L. • 52.81.11.56.99.20 • 01-800-226-6766 • mela@omron.com OTHER OMRON LATIN AMERICA SALES 54.11.4783.5300 OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICE São Paulo, SP, Brasil • 55.11.2101.6300 • www.omron.com.br OMRON EUROPE B.V. • Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands. • +31 (0) 23 568 13 00 • www.industrial.omron.eu Authorized Distributor: Automation Control Systems • Machine Automation Controllers (MAC) • Programmable Controllers (PLC) • Operator interfaces (HMI) • Distributed I/O • Software Drives & Motion Controls • Servo & AC Drives • Motion Controllers & Encoders Temperature & Process Controllers • Single and Multi-loop Controllers Sensors & Vision • Proximity Sensors • Photoelectric Sensors • Fiber-Optic Sensors • Amplified Photomicrosensors • Measurement Sensors • Ultrasonic Sensors • Vision Sensors Industrial Components • RFID/Code Readers • Relays • Pushbuttons & Indicators • Limit and Basic Switches • Timers • Counters • Metering Devices • Power Supplies Safety • Laser Scanners • Safety Mats • Edges and Bumpers • Programmable Safety Controllers • Light Curtains • Safety Relays • Safety Interlock Switches J52I-E-01 08/14 Note: Specifications are subject to change. Printed on recycled paper. © 2014 Omron Electronics LLC Printed in U.S.A.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : OMRON Create Date : 2014:04:15 15:18:37-05:00 Keywords : SR103AM Dual Channel Safety Monitoring Relay, STI, 1 or 2 NC inputs, 3 NO outputs, 1 NC auxiliary output, External Device Monitoring (EDM) is provided with a NC loop between S11/S12 and S21 terminals Modify Date : 2015:04:08 17:49:01-05:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Instance ID : uuid:71cafb95-6a84-49b9-982f-67bc88d2a193 Original Document ID : adobe:docid:indd:43031250-5757-11de-b0bf-a560c17a1bc9 Document ID : xmp.id:DD3C5A0322206811822AF4C4D1FD7259 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:94B2B6FA13206811822AF4C4D1FD7259 Derived From Document ID : xmp.did:FB9E5278292368118083D366F236A913 Derived From Original Document ID: adobe:docid:indd:43031250-5757-11de-b0bf-a560c17a1bc9 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Macintosh) History Changed : / History When : 2014:04:15 15:18:37-05:00 Metadata Date : 2015:04:08 17:49:01-05:00 Creator Tool : Adobe InDesign CS6 (Macintosh) Format : application/pdf Title : SR103AM Dual Channel Safety Monitoring Relay Data Sheet Description : SR103AM Dual Channel Safety Monitoring Relay Creator : OMRON Subject : SR103AM Dual Channel Safety Monitoring Relay, STI, 1 or 2 NC inputs, 3 NO outputs, 1 NC auxiliary output, External Device Monitoring (EDM) is provided with a NC loop between S11/S12 and S21 terminals Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 6 Warning : [Minor] Ignored duplicate Info dictionaryEXIF Metadata provided by EXIF.tools