TM8000 3DK Hardware Developer’s Kit Application Manual TM8000/TM8100 TM8200 Developers Manual/TM8100 TM8100
User Manual: Pdf TM8000/TM8100-TM8200 3DK Hardware Developers Kit Application Manual/TM8100-TM8200 3DK Hardware Developers Kit Application Manual
Open the PDF directly: View PDF
Page Count: 156 [warning: Documents this large are best viewed by clicking the View PDF Link!]
- 3DK Hardware Developer’s Kit Application Manual
- Contents
- Preface
- 1 Introduction
- 2 Description of the Radio Interfaces
- 2.1 RF Connector
- 2.2 Power Connector
- 2.3 Auxiliary Connector
- 2.4 Internal Options Connector
- 2.5 Provision for External Options Connector
- 2.6 Provision for Additional Connector (SMA)
- 2.7 Control Head Connector
- 2.8 Microphone Connector
- 2.9 Blank Control Head Programming Connector
- 2.10 RJ45 Control Head Programming Connector
- 3 Programmable I/O Lines
- 3.1 Digital Input Lines
- 3.1.1 Toggle Stand-by Mode
- 3.1.2 Power Sense (Ignition)
- 3.1.3 Enter Emergency Mode
- 3.1.4 Send Channel Preset Call
- 3.1.5 Send Network Preset Call 1
- 3.1.6 External Call (ECR)
- 3.1.7 External PTT 1 and 2
- 3.1.8 Inhibit PTT
- 3.1.9 Toggle Tx RF Inhibit
- 3.1.10 Decrement Channel
- 3.1.11 Increment Channel
- 3.1.12 Home Channel
- 3.1.13 BCD Pin 0 to 4
- 3.1.14 Preset Channel
- 3.1.15 Mute External Audio Input
- 3.1.16 Mute Audio Output Path
- 3.1.17 Unmute Audio Output Path
- 3.1.18 Send Mic Audio to Spkr
- 3.1.19 Force Audio PA On
- 3.1.20 Force Audio PA Off
- 3.1.21 Simulate F1 to F4 Key
- 3.1.22 Toggle F1toF4 Key LED
- 3.1.23 Toggle Alarm Mode
- 3.1.24 Activate THSD Modem
- 3.1.25 RTS Control (DCE)
- 3.1.26 Lock Radio UI (PIN to unlock)
- 3.2 Digital Output Lines
- 3.2.1 Busy Status
- 3.2.2 Radio Has Service
- 3.2.3 Radio Transmission Status
- 3.2.4 Channel Locked Status
- 3.2.5 Reflected PTT Status
- 3.2.6 External Alert 1 and 2
- 3.2.7 Public Address Status
- 3.2.8 Reflected PTT Inhibit Status
- 3.2.9 Reflect THSD Modem Status
- 3.2.10 Signalling Audio Mute Status
- 3.2.11 Radio On Traffic Channel
- 3.2.12 On Data Traffic Channel
- 3.2.13 Monitor Status
- 3.2.14 Hookswitch Status
- 3.2.15 Call Setup Status
- 3.2.16 Radio Idle
- 3.2.17 Control Status Rx (Line 1 to 3)
- 3.2.18 SIBT Received
- 3.2.19 Radio Stunned
- 3.2.20 F1 to F4 Key Status
- 3.2.21 FFSK Data Received Status
- 3.2.22 CTS Control (DCE)
- 3.2.23 Ready For NPD
- 3.2.24 Serial Data Tx In Progress
- 3.2.25 Radio Ready
- 3.3 Audio Tap In and Tap Out Lines
- 3.1 Digital Input Lines
- 4 Creating Your Own Options Board
- 5 Connecting Third-Party Products
- 6 Connecting an External Alert Device
- 7 Computer-Controlled Radio
- 7.1 Introduction
- 7.2 Programmable Parameters
- 7.3 Command Protocol
- 7.4 Command Description
- 7.5 CCR Mode Commands
- 7.6 CCR Positive Acknowledgements
- 7.7 CCR Negative Acknowledgements
- 7.8 CCR Commands
- 7.8.1 Summary and Examples
- 7.8.2 Go to Receive Frequency
- 7.8.3 Load Transmit Frequency
- 7.8.4 Set Volume Level
- 7.8.5 Receive CTCSS Value
- 7.8.6 Transmit CTCSS Value
- 7.8.7 Receive DCS Value
- 7.8.8 Transmit DCS Value
- 7.8.9 Encode Selcall Sequence
- 7.8.10 Set Selcall Parameters
- 7.8.11 Set ANI
- 7.8.12 Monitor
- 7.8.13 Transmitter Output Power
- 7.8.14 Set Bandwidth
- 7.8.15 Query Radio Pulse
- 7.8.16 Exit CCR Mode
- 7.9 Unsolicited Messages from the Radio
- Tait General Software Licence Agreement