Traverse Led Turtle Spec Sheet
2014-07-23
: Pdf Traverse Led Turtle Spec Sheet traverse_led_turtle_spec_sheet spec products beacon
Open the PDF directly: View PDF 
.
Page Count: 2
design . performance . technology
ORDERING2041 58th Avenue Circle East Bradenton, 34203 Phone: (800) 345-4928 Fax: (941) 751-5535
www.beaconproducts.com
Type:
Project Name:
Notes:
DETAILS
rev. 03.26.2014
A. MODEL H. COLOR
TRV-D Traverse down-light BBT basic black textured
BMT black matte textured
B. ENGINE-WATTS WHT white textured
24E-32 32 Watts - LED array MBT metallic bronze textured
36E-48 48 Watts - LED array BZT bronze textured
48E-63 63 Watts - LED array DBT dark bronze textured
60E-80 80 Watts - LED array GYS gray smooth
DPS dark platinum smooth
GNT green textured
C. LED CHIP WAVELENGTH MST metallic silver textured
AMB amber 590nm (std.) MTT metallic titanium textured
OWI old world iron
D. OPTICS RAL ______________
T2 type II
T3 type III
T4 type IV
E. SHIELDING
90 90° shield
180 180° shield
270 270° shield
F. VOLTAGE
UNV 120-277V
347 347V
480 480V
G. ELECTRICAL OPTIONS
PEC photocell, button
MOB motion sensor 33% or 50%
dimming
OCS occupancy sensor (on/off)
TRAVERSE (LED)
Traverse Wall Pack
Max Weight: 24.0 lbs
Sample TRV-D 60E-80 AMB T2 180 UNV PEC BBT
Ordering / / / / / / /
A B C D E F G H
Turtle Friendly
MOB ORDERING INFORMATION: When ordering a xture with the motion de-
tection option (MOB), please specify the appropriate information. These settings
are specied in the ordering as shown in the example below.
TRV-D / 48E-63 / AMB / T5SW / 180 / UNV / MOB - __________ - __________ - _____ / MT
1 to 30 min.33% or 50%
High to Dim Delay Low Level Mounting Height (ft.)
??
14”
12 1/2”
7 1/4”
Side View
Front View
Bottom View Top View
design . performance . technology
SPECIFICATION2041 58th Avenue Circle East Bradenton, 34203 Phone: (800) 345-4928 Fax: (941) 751-5535
rev. 03.26.2014
Due to our continued eorts to improve our products, product specications are subject to change
without notice.
TRAVERSE (LED)
Traverse Wall Pack
Max Weight: 24.0 lbs
Turtle Friendly
General: The Beacon TRV luminaire is a wall surface mounted luminaire with a eld
replaceable LED light engine & optical bezel system. Internal components are totally
enclosed in rain-tight and corrosion-resistant die cast aluminum housing. The TRV Lu-
minaire is suitable for wet locations.
Housing/LED Thermal Management: The Beacon TRV luminaire consists of a die
cast aluminum two-piece housing. The die cast main (thermal) housing provides direct
heat exchange between the LED light engine and the cool outdoor air by drawing heat
through integral heat channels and out to the sculptured and functional luminaire sur-
face. LED drivers are thermally isolated from the main housing, mechanically attached
and heat sinked to the rear housing. The main housing is designed with heat dissipating
ns for LED thermal management without the use of metallic screens, cages, or fans.
The shape of the main housing is designed to prevent debris accumulation and as a bird
nesting deterrent. The back and main housings are designed to hinge open for easy
mounting and easy access.
Mounting & Installation: The rear housing (back plate) is designed with various bolt
patterns for direct wall mounting or mounting to a recessed 4” junction box The rear
housing has three integral 3/4” NPT power feed locations (bottom and each side) for
surface mounted conduit applications. After mounting the rear housing to the wall or
junction box the main housing is designed to hang and hinge closed after connecting
the male and female quick connectors. The mounting design permits a simple retrot to
existing wall luminaires that utilize surface mount or recessed junction boxes.
Bezel Optical System: Each Traverse luminaire is supplied with an Optical one piece
cartridge system consisting of an LED engine, LED lamps, optics, gasket and stainless
steel bezel. The cartridge is held together with internal brass standoffs soldered to the
board so that it can be eld replaced as a one piece Optical system. A two-piece die
cut silicone and polycarbonate foam gasket ensures a weather-proof seal around each
individual LED and allows the Traverse luminaire to be rated for high-pressure hose down
(IP67) applications.
The optical cartridge is secured to the extruded housing with fasteners and a heat pad
to ensure thermal conductivity. The optics are held in place without the use of adhesives
and the complete assembly is gasketed for high pressure hose down cleaning. The
cartridge assembly is available in various lighting distributions using TIR designed Acrylic
optical lenses over each LED.
Printed Circuit Board (PCB): Aluminum thermal clad board with 0.062” thick alumi-
num base layer “high temperature” HT-06503 or equivalent (subject to change) dielectric
(0.003” thick, thermal conductivity of 2.2 W/MK, UL RTI of 140°C) 0.0014” thick copper
circuit layer Circuit layer designed with copper pours to minimize thermal impedance
across dielectric. Board shall be supplied with QPAD-3 berglass reinforced thermal pad
0.005” thick thermal conductivity of 2.0 W/Mk. Continuous use temperature of 180°C
UL94 V-0. Board will be mounted to the heat sink using 12 #4-40 screws to ensure con-
tact with thermal pad and heat sink. Use of thermal grease will not be allowed.
LifeShield™ Circuit: (optional) Thermal circuit shall protect the luminaire from exces-
sive temperature by interfacing with its 0-10V dimmable drivers to reduce drive cur-
rent as necessary. The factory-preset temperature limits shall be designed to ensure
maximum hours of operation to assure L70 rated lumen maintenance. The device shall
activate at a specic, factory-preset temperature, and progressively reduce power over
a nite temperature range in recognition of the effect of reduced current on the internal
temperature and longevity of the LEDs and other components.
A luminaire equipped with the device may be reliably operated in any ambient tempera-
ture up to 55ºC (131ºF).
The LifeShield™ thermal regulation circuit will allow higher maximum Wattages than
would be permissible on an unregulated luminaire (if some variation in light output is
permissible), without risk of premature LED failure.
Operation shall be smooth and undetectable to the eye. Thermal circuit shall directly
measure the temperature at the LED solder point.
LifeShield™ shall consist of surface mounted components mounted on the LED engine
(printed circuit board). For maximum simplicity and reliability, the device shall have no
dedicated enclosure, circuit board, wiring harness, gaskets, or hardware. Device shall
have no moving parts, and shall operate entirely at low voltage (NEC Class 2). The device
shall be located in an area of the luminaire that is protected from the elements.
LifeShield™ shall be designed to “fail on”, allowing the luminaire to revert to full power in
the event of an interruption of its power supply, or faulty wiring connection to the drivers.
Device shall be able to co-exist with other 0-10V control devices (occupancy sensors,
external dimmers, etc.). The device will effectively control the solder point temperature as
needed; otherwise it will allow the other control device(s) to function unimpeded.
Motion Activated Luminaires: Beacon TRV luminaires are available with an optional
passive infrared (PIR) motion sensor capable of detecting motion within 24 feet of the
sensor, 360° around the luminaire, when placed at an 8 foot mounting height. When no
motion is detected for 5 minutes, the Motion Response system reduces the Wattage
from 10% to 50% (factory set at 50% reduction) of the maximum Wattage, reducing the
light level accordingly. When motion is detected by the PIR sensor, the luminaire returns
to full Wattage and full light output. Please contact Beacon Products if project require-
ments vary from standard conguration.
Electrical: Luminaires are equipped with an LED driver that accepts 100V through 277V,
50 Hz to 60 Hz (UNIV), or a driver that accepts 347V or 480V input. Power factor is .92
at full load. All electrical components are rated at 50,000 hours at full load and 40°C
ambient conditions per MIL-217F Notice 2. Optional 0 to 10 volt dimming drivers are
available upon request. Component-to-component wiring within the luminaire may carry
no more than 80% of rated load and is listed by UL for use at 600VAC at 50°C or higher.
Plug disconnects are listed by UL for use at 600 VAC, 15A or higher. 15A rating applies
to primary (AC) side only.
Surge Protector: The on-board surge protector shall be a UL recognized component
for the United States and Canada and have a surge current rating of 20,000 Amps using
the industry standard 8/20 pSec wave. The LSP shall have a clamping voltage of 825V
and surge rating of 540J. The case shall be a high-temperature, ame resistant plastic
enclosure.
Cold Weather Battery Pack: The emergency driver shall be capable of operating an
LED load of up to 23.1 Watts at rated current (700 mA) for a minimum of 90 minutes. It is
suitable for damp locations as well as sealed and gasketed xtures. The BPC shall have
37 Watts of input power and a 54.0 Watts-hour battery capacity and shall comply with
emergency standards set forth by the current NEC.
Fasteners: All fasteners shall be stainless steel. When tamper resistant fasteners are
required, spanner HD (snake eye) style shall be provided (special tool required, consult
factory).
Power Supply/Driver Requirements: U.L. UL1310, Class 2 and UL48 compliant.
Operating Environment: Shall be able to operate normally in ambient temperatures
from -40°C to 40°C.
Finish: Finish shall be a Beacote V polyester powder-coat electro-statically applied and
thermocured. Beacote V nish shall consist of a ve stage iron phosphate chemical pre-
treatment regimen with a polymer primer sealer, oven dry off, and top coated with a
thermoset super TGIC polyester powder coat nish. The nish shall meet the AAMA
605.2 performance specication which includes passing a 3000 hour salt spray test for
corrosion resistance and resists cracking or loss of adhesion per ASTM D522 and resists
surface impacts of up to 160 inch-pound.
Agency Certication: The luminaire shall bear a CSA label and be marked suitable for
wet locations.
Warranty: Beacon luminaires feature a 5 year limited warranty. Beacon LED luminaires
with LED arrays feature a 5 year limited warranty covering the LED arrays. LED drivers are
covered by a 5 year limited warranty. PIR sensors carry a 5 year limited warranty from the
sensor manufacturer. See Warranty Information on www.beaconproducts.com complete
details and exclusions.
