演示文稿 Tronxy X1 Assemble Guide V.02

User Manual: Pdf

Open the PDF directly: View PDF .
Page Count: 26

Step 1 Assemble Base Frame

Parts:

2040 Aluminium profile 250mm –1pcs

Base Plate –1pcs

M4-8mm screw –3pcs

M4 T-Nut –3pcs

-Put the aluminium profile on the base plate,

secure them with 3pcs M4-10mm screws & T-Nut

Step 2 Assemble Base Frame

Parts:

2020 Aluminium profile 70mm –1pcs

Corner bracket –2pcs

M4-8mm screw –5pcs

M4 T-Nut –5pcs

-Put the ‘2020 aluminium profile 70mm’ on the

base plate, secure them with 1pcs M4-8mm

screws & T-Nut

-Fix the aluminium profiles using 2pcs corner

bracket, secure them with M4-8mm screws and

M4 T-Nuts.

Step 3 Install Z Slide rail

Parts:

2040 Aluminium profile 310mm –1pcs

Corner bracket –1pcs

M5-10mm screw -2pcs

M5-40mm screw –1pcs

M4-8mm screw –2pcs

M4 T-Nut –2pcs

-Place ‘2040 aluminium profile 310mm’ on the

base plate , secure them with 2pcs M5-10mm

screws.

-Fix the 2pcs aluminium profile with 1pcs corner

bracket, secure them with 2pcs M4-8mm screws

and M4 T-Nut.

-Use 1pcs M5-40mm screw to make them more

stable

Step 4 Fix the Z slide rail

Parts:

L-shape Acrylic block –1pcs

M4-8mm screw –4pcs

M4 T-Nut –4pcs

-Place 1pcs L-shape acrylic block on the

aluminium profile, secure them with 4pcs

M4-8mm screws & T-Nut

Step 5 Assemble Y axis Motor

Parts:

42 stepper motor –1pcs

GT2-16 Pulley (with grub screw in it)–1pcs

Limit switch –1pcs

Y motor mount (Acrylic) –1pcs

M3-8mm screws –4pcs

M4-8mm screw –3pcs

M4 T-Nut - 3pcs

M2-10mm screw –2pcs

M2 Nut –2pcs

-Insert the GT2-16 pulley to the motor shaft,

tighten the grub screw in the pulley. Next

assemble the 42 stepper motor and the Y motor

mount(Acrylic) with 4pcs M3-8mm screws .

-Secure the limit switch to motor mount using

2pcs M2-10mm screws and nuts.

-secure the motor mount to the back of the Y

slide rail using 3pcs M4-8mm screws and T-nuts.

Step 6 Assemble Bed Frame

Parts:

Bed frame (acrylic) –1pcs

Wheel –3pcs

Plastic pillar –3pcs

M5-30mm- 3pcs

M5 nut –3pcs

GT2 Timing belt –1pcs

Zip-ties –1pcs

-Secure the wheels in place using M5-30mm

screws and nuts ,using plastic pillar between

wheel and bed frame.

-Tighten one end of the timing belt to the bed

frame using a zip-ties.

-Next slide the base frame to the 2040 aluminium

profile .

Step 7 Assemble Y-axis Belt Pulley

Parts:

Y Pulley mount (acrylic) –1pcs

Belt pulley –1pcs

M5-25mm screw –1pcs

M5 Nut –2pcs

M6 washer –2pcs

M5 washer –2pcs

M4-8mm screw –3pcs

M4 T-Nut - 3pcs

-Take 1pcs M5-25mm screw and insert the Pulley

mount, secure it with M5 nut , then insert the

washers and belt pulley , secure them using M5

nut.

-Secure the Y belt pulley assembly to the front of

the Y slide rail using 3pcs M4-8mm screws and

nuts.

-Tighten screws gently to avoid damaging the

acrylic.

Step 8 Install Y axis Timing Belt

Parts:

Zip-ties –1pcs

-Run the other end of timing belt along the

aluminium profile, through the Y-GT2-16 Pulley

and Belt pulley . Then tighten it to the bed frame

using zip-ties as shown in the picture .

Step 9 Assemble Z Carriage

Parts:

2020 Aluminium profile 285mm –1pcs

X-motor mount (acrylic) –1pcs

Extruded bracket –1pcs

Brass nut –1pcs

Plastic pillar –6pcs

Wheel –3pcs

M5-40mm screw –3pcs

M5 Locknut –3pcs

M3-8mm screw –3pcs

M4-8mm screw –2pcs

M4 T-Nut - 2pcs

-Insert 3pcs M5-40mm screws to X-motor mount ,

and then scure it to the aluminium profile using

2pcs M4-8mm screws and T-nuts.

-Put the wheels into M5-40mm screws, using

plastic pillars between wheel and acrylic, secure

the Extruded bracket using M5 nuts.

-Place the brass nut on the extruded bracket,

scure it using 3pcs M3-8mm screws .

Step 10 Install Z carriage

Parts:

42 stepper motor –1pcs

GT2-16 Pulley (with grub screw in it)–1pcs

M3-8mm screws –4pcs

-Carefully insert the X-axis assembly to the Z slide

rail

-Insert the GT2-16 pulley to the motor shaft,

tighten the grub screw in the pulley, then place

the X stepper motor to the motor mount, secure

them with 4pcs M3-8mm screws .

Step 11 Insert Extruder Assembly

Parts:

Extruder assembly –1pcs

-Carefully insert the extruder assembly to the X

slide rail.

Step 12 Assemble X axis Endstop & Pulley

Parts:

Belt pulley –1pcs

Limit switch –1pcs

X Pulley mount (acrylic) –1pcs

X endstop mount (acrylic) –1pcs

M5-25mm screw –1pcs

M5 Nut –1pcs

M5 Locknut –1pcs

M6 washer –2pcs

M5 washer –2pcs

M4-8mm screw –4pcs

M4 T-Nut - 4pcs

M2-10mm screw –2pcs

M2 Nut –2pcs

-Secure the limit switch to X endstop mount using

2pcs M2-10mm screws and nuts. Then place the

X endstop mount to the left end of the X slide rail

using 2pcs M4-8mm screw and T-nuts.

-Take 1pcs M5-25mm screw and insert the Pulley

mount, secure it with M5 nut , then insert the

washers and belt pulley , secure them using M5

locknut.

-Secure the X belt pulley assembly on the right of

the X slide rail using 2pcs M4-8mm screws and

nuts.

Step 13 Install X axis Timing Belt

Parts:

GT2 Timing belt –1pcs

Zip-ties –2pcs

-Tighten one end of the timing belt to the belt

hole using a zip-ties which back of the extruder

-Run the other end of timing belt along the

aluminium profile, through the X-GT2-16 Pulley

and Belt pulley . Then tighten it to another belt

hole using a zip-ties, as shown in the picture .

Step 14 Assemble Z motor

Parts:

42 Stepper motor –1pcs

Z-motor seat –1pcs

Coupling (with grub screw in it) –1pcs

Threaded rod 260mm –1pcs

M3-8mm screw –4pcs

M4-12mm screw –2pcs

M4 T-Nut –2pcs

-Place 1pcs 42 stepper motor back of the Z slide

rail , put the motor seat on the motor and then

secure them with 4pcs M3-8mm screws.

-Install them to the Z slide rail using 2pcs M4-

12mm screws and T-Nuts.

-Take 1pcs threaded rod through the brass

nut ,then insert to the coupling and tighten up.

Step 15 Install Filament Feeder

Parts:

42 Stepper motor –1pcs

Feeding gear (with grub screw in it)–1pcs

Extrution clip - 1pcs

Extrution seat –1pcs

M3-22mm –2pcs

M3-16mm –1pcs

M5-10mm Hex screw –1pcs

Spring –1pcs

-Insert the feeding gear to the motor shaft and

them tighten up .

-Place the Extrution seat and motor to the bracket

as shown in the picture, secure them using 2pcs

M3-22mm screws.

-Put one M5-10mm hex screw and spring

between extrution clip and extrution seat , next

secure the extrution clip with motor using M3-

16mm screw.

Step 16 Install handle

Parts:

Handle –1pcs

Handle seat (Acrylic) –1pcs

M5-10mm screw –2pcs

M4-12mm screw –2pcs

-Put the handle seat on the top of Z slide rail,

secure them with 2pcs M5-10mm screws .

-Secure the handle to the seat using 2pcs

M4-12mm screws .

Step 17 Install Z endstop

Parts:

Limit switch –1pcs

Z endstop mount –1pcs

M4-8mm screw –1pcs

M4 T-Nut –1pcs

M2-10mm screw –2pcs

M2 Nut –2pcs

-Secure the limit switch to Z endstop mount using

2pcs M2-10mm screws and nuts.

-Place the Z endstop mount to the left Z slide rail,

using one M4-8mm screw and T-nut.

Step 18 Assemble Print bed

Parts:

Bed plate –1pcs

M3-30mm screw –4pcs

Thumb nut –4pcs

Spring –4pcs

-Place the Bed plate on the bed frame use 4pcs

springs between them, and then through 4pcs

M3-30mm screws, then top 4pcs thumb nuts

under the bed frame.

Step 19 Install Teflon hose

Parts:

Teflon hose –1pcs

Connector –1pcs

-Install a connector to the filament feeder , and

then insert a teflon hose between feeder and

extruder .

Step 20-1 Assemble Electronic Box

Parts:

Electronic box bottom plate (acrylic) –1pcs

Electronic box side plate –2pcs

Mainboard–1pcs

M3-20mm screws –6pcs

M3 nuts –6pcs

Plastic pillar –4pcs

-Place the mainboard on the bottom plate using

M3-20mm and nuts , insert the plactic pillar

between them.

-Assemble the side plates to the bottom plate as

picture , secure them using M3-20mm screw&nut

Step 20-2 Assemble Electronic Box

Parts:

Electronic box front plate –1pcs

LCD display assembly –1pcs

M3-20mm screws –4pcs

M3 nuts –4pcs

-Assemble the front plate using M3-20mm screws

and M3 nuts.

-Place the LCD display assembly to the box , using

2pcs M3-20mm screws and nuts.

Step 20-3 Assemble Electronic Box

Parts:

Electronic box Back plate (left) –1pcs

DC power jack –1pcs

M3-20mm screws –1pcs

M3 nuts –1pcs

-Assemble the back plate to the bottom plate as

picture , secure them using M3-20mm screw&nut.

-Insert the DC power jack to the back plate.

Step 20-4 Assemble Electronic Box

Parts:

Electronic box top plate –1pcs

M3-20mm screws –3pcs

M3 nuts –3pcs

-Cover the top plate using M3-20mm screws and

M3 nuts.

Step 23 Control Board Wiring Diagram

Parts:

Mainboard –1pcs

-The method of connecting wire is as picture

-There is only 1pcs cooler fan , please connect to

‘CFAN’ on board

-There do not have heatbed and the thermistor ,

so there's no connection on ‘Hotbed’ and ‘BTEMP’.

x

x

x

x

DC power jack