Viper Small Led Spec Sheet
2014-07-23
: Pdf Viper Small Led Spec Sheet viper_small_led_spec_sheet spec products beacon
Open the PDF directly: View PDF 
.
Page Count: 2
design . performance . technology
ORDERING2041 58th Avenue Circle East Bradenton, 34203 Phone: (800) 345-4928 Fax: (941) 751-5535
www.beaconproducts.com
Type:
Project Name:
Notes:
DETAILS
rev. 06.16.2014
VIPER - SMALL (LED)
Small Viper Luminaire
Max Weight: 15.0 lbs
Max EPA: 0.67 sq ft
Accepts 2 3/8” OD
tenon, min 4” long.
PK2 2-3/8” Adjustable Knuckle
Front
SF2 2-3/8” OD Slip Fitter
RA Rectangular Arm
Side View
Side View
Back View
Back View
Sample VP-S 30NB-90 5K T5R UNV PCR-TL SF2 BBT
Ordering / / / / / /
A B C D E F G H
A. MODEL F. ELECTRICAL OPTIONS
VP-S Viper - Small PCR-TL photocell, twist-lock
PCR-SC photocell, shorting cap
B. ENGINE-WATTS 2PF dual power feed 1,2
22NB-50 50 Watts - LED array
22NB-70 70 Watts - LED array G. MOUNTING OPTIONS
30NB-70 70 Watts - LED array RA rectangular arm
30NB-90 90 Watts - LED array SF2 2 3/8” OD slip-tter
PK2 2 3/8” adjustable knuckle
C. CCT - COLOR TEMP WB wall bracket
5K 5000K (std.)
4K 4000K
3K 3000K H. COLOR
BBT basic black textured
D. OPTICS BMT black matte textured
T2 type II WHT white textured
T3 type III MBT metallic bronze textured
T4 type IV BZT bronze textured
T5R type V, rectangular DBT dark bronze textured
T5QM type V, square medium GYS gray smooth
T5W type V, round wide DPS dark platinum smooth
GNT green textured
E. VOLTAGE MST metallic silver textured
UNV 120-277V MTT metallic titanium textured
347V 347V OWI old world iron
480V 480V RAL ______________
1 not available with 30NB-90
2 not available @ 347V or 480V input
16 3/4”
22 3/4”
11 1/4”
4 1/8”
MOUNTING OPTIONS
18 3/4”
6 5/8”
DRILL PATTERN
4” Suggested distance
from top of pole 2.50”
2X Ø5/16”
Ø5/8”
Rectangular Arm
Ø4” Pole
Ø5” Pole
Ø6” Pole
WB Wall Bracket
23 3/4”
6”
5 1/2”
5”
2 3/8”
1”
1/2”
6”
design . performance . technology
SPECIFICATION2041 58th Avenue Circle East Bradenton, 34203 Phone: (800) 345-4928 Fax: (941) 751-5535
rev. 06.16.2014
Due to our continued eorts to improve our products, product specications are subject to
change without notice.
Surge Protector: The on-board surge protector shall be a UL recognized component
for the United States and Canada and have a surge current rating of 20,000 Amps using
the industry standard 8/20 pSec wave. The LSP shall have a clamping voltage of 825V
and surge rating of 540J. The case shall be a high-temperature, ame resistant plastic
enclosure.
Fasteners: All fasteners shall be stainless steel. When tamper resistant fasteners are
required, spanner HD (snake eye) style shall be provided (special tool required, consult
factory).
Color Rendering Index (CRI): Luminaire shall have a minimum CRI of 67 at 5000K.
Operating Environment: Shall be able to operate normally in ambient temperatures
from -40°C to 40°C
Finish: Finish shall be a Beacote V polyester powder-coat electro-statically applied and
thermocured. Beacote V nish shall consist of a ve stage iron phosphate chemical pre-
treatment regimen with a polymer primer sealer, oven dry off, and top coated with a
thermoset super TGIC polyester powder coat nish. The nish shall meet the AAMA
605.2 performance specication which includes passing a 3000 hour salt spray test for
corrosion resistance and resists cracking or loss of adhesion per ASTM D522 and resists
surface impacts of up to 160 inch-pound.
Agency Certication: The luminaire shall bear a CSA label and be marked suitable for
wet locations.
Warranty: Beacon luminaires feature a 5 year limited warranty. Beacon LED luminaires
with LED arrays feature a 5 year limited warranty covering the LED arrays. LED drivers are
covered by a 5 year limited warranty. PIR sensors carry a 5 year limited warranty from the
sensor manufacturer. See Warranty Information on www.beaconproducts.com complete
details and exclusions.
VIPER - SMALL (LED)
Small Viper Luminaire
Max Weight: 15.0 lbs
Max EPA: 0.67 sq ft
Power/Lumens & Distrubutions
General: The Beacon Viper luminaire is available in two sizes with a wide choice of
different LED Wattage congurations and optical distributions designed to replace HID
lighting up to 1000W MH or HPS and with 5 different mounting options for application in
a wide variety of new and existing installations. Luminaires are suitable for wet locations.
Bezel Optic System: Each Viper luminaire is supplied with an one piece optical car-
tridge system consisting of an LED engine, LED lamps, optics, gasket and stainless
steel bezel. The cartridge is held together with internal brass standoffs soldered to the
board so that it can be eld replaced as a one piece optical system. Two-piece silicone
and micro-cellular polyurethane foam gasket ensures a weather-proof seal around each
individual LED.
The optical cartridge is secured to the die cast housing with fasteners. The optics are
held in place without the use of adhesives. The cartridge assembly is available in various
lighting distributions using TIR designed acrylic optical lenses over each LED.
Lifeshield™ Circuit: Thermal circuit shall protect the luminaire from excessive tempera-
ture by interfacing with the 0-10V dimmable drivers to reduce drive current as necessary.
The factory-preset temperature limits shall be designed to ensure maximum hours of
operation to assure L70 rated lumen maintenance. The device shall activate at a specic,
factory-preset temperature, and progressively reduce power over a nite temperature
range.
A luminaire equipped with the device may be reliably operated in any ambient tem-
perature up to 55ºC (131ºF). The thermal circuit will allow higher maximum Wattages
than would be permissible on an unregulated luminaire (if some variation in light output
is permissible), without risk of premature LED failure or lumen depreciation. Operation
shall be smooth and undetectable to the eye. Thermal circuit shall directly measure the
temperature at the LED solder point. Thermal circuit shall consist of surface mounted
components mounted on the LED engine (printed circuit board). For maximum simplicity
and reliability, the device shall have no dedicated enclosure, circuit board, wiring harness,
gaskets, or hardware. Device shall have no moving parts, and shall operate entirely at
low voltage. The device shall be located in an area of the luminaire that is protected
from the elements. Thermal circuit shall be designed to “fail on”, allowing the luminaire
to revert to full power in the event of an interruption of its power supply, or faulty wiring
connection to the drivers.
Device shall be able to co-exist with other 0-10V control devices (occupancy sensors,
external dimmers, etc.). The device will effectively control the solder point temperature as
needed; otherwise it will allow the other control device(s) to function unimpeded.
Printed Circuit Board (PCB): Aluminum thermal clad board with 0.062” thick aluminum
base layer, thermally conductive dielectric layer, 0.0014” thick copper circuit layer cir-
cuit layer designed with copper pours to minimize thermal impedance across dielectric.
Board will be mounted to the heat sink using minimum 12 #4-40 screws to ensure con-
tact with thermal pad and heat sink. Use of thermal grease will not be allowed.
Housing and LED Thermal Management: The Viper’ monolithic housing design cre-
ates over 4.5 square feet (small Viper) or 7.7 square feet (large Viper) of heat-sinking sur-
face area. Vertical ns, combined with ow-thru openings prevent sediment and moisture
buildup on critical heat sinking surfaces without the need for grates, screens or other
debris control tactics. The Viper housing, electrical compartment and tter are made
from die cast aluminum that is pre-treated and powder-coated to meet the most rugged
industry standards. The nish is corrosion resistant to meet ASTMB-117, resists cracking
or loss of adhesion per ASTM D522, resists surface impacts of up to 160 inch-pound. All
external hardware is corrosion resistant. The housing serves as a heat-sink for the LED
bezel with a separate compartment for the drivers.
Electrical Assembly: The xture electrical compartment shall contain all LED driver
components and shall be provided with a push-button terminal block for AC power
connections. The housing is designed for an optional twist lock photo control receptacle.
Accessibility: Although the Viper luminaire is designed to operate for many years with-
out maintenance, accessibility is a key component in its design. The Drivers are mounted
on a removable door that is secured with keyslotted screws and hinges down for conve-
nient access. The drivers are eld replaceable using quick disconnects.
Drivers: Luminaires are equipped with an LED driver that accepts 100V through 277V,
50 Hz to 60 Hz (UNIV), or a driver that accepts 347V or 480V input. Power factor is .92
at full load. All electrical components are rated at 50,000 hours at full load and 25°C am-
bient conditions per MIL- 217F Notice 2. Dimming drivers are standard, with connections
for external dimming equipment available upon request. Component-to-component wir-
ing within the luminaire may carry no more than 80% of rated load and is listed by UL for
use at 600VAC at 50°C or higher. Plug disconnects are listed by UL for use at 600 VAC,
13A or higher. 13A rating applies to primary (AC) side only.
Engine Wattage
Delivered
Lumens
(varies by optic)
Delivered
LPW
TM21 Calculated % Lumen
Maint.
at 100,000 hrs
22NB 50 4700-5020 93-103 96.19%
22NB 70 5780-6200 82-103 85.79%
30NB 70 6408-6850 91-103 95.02%
30NB 90 7700-8260 85-97 85.79%
TM21 is the framework for taking LM-80 data and making useful LED lifetime projec-
tions. Reported and Calculated Lifetimes shown are based on hours at the time of
this printing. For current Reported and Calculated hours please contact factory or
Beacon’s web-site.
CCT (COLOR TEMP)
Lumen Output
Multipliers
CRI
(Color Rendering)
5000K = 1.0 min 67 CRI
4000K = .92 min 70 CRI
3000K = .75 min 80 CRI
