YAESU FT 1000MP MARK V Brochure

User Manual: Pdf YAESU--FT-1000MP-MARK-V-Brochure

Open the PDF directly: View PDF .
Page Count: 8

FT-1000MP

MARK-V

HF 200W ALL MODE TRANSCEIVER

The MARK-V utilizes a pair of Philips BLF147 Power

MOSFETs in a 30-Volt, push-pull configuration.

These 300-Watt (150-Watt x 2) transistors are run well

below their

maximum ratings, ensuring high reliability

and excellent

signal purity. The time-proven Low-Pass

Filter network, adopted from the FT-1000D, effectively

suppresses harmonic energy while efficiently delivering

at least 200 Watts to the antenna jack.

The basic circuitry from the widely-acclaimed Automatic

Antenna Tuner of the FT-1000MP has been beefed

up for operation at the 200-Watt level for incorporation

in the MARK-V. Constructed on a glass-epoxy circuit

board for maximum efficiency, the Automatic Antenna

Tuner’ s dedicated microprocessor utilizes a complex

analysis algorithm

which permits lightning

-quick matching of

impedance mismatches.

The result : more

power delivered to

the antenna, and less

time wasted in tuning!

I. 200 WATTS PEP TRANSMITTER OUTPUT

■

Conservatively-Designed 200 W MOSFET Final Amplifier

Philips

MOS FET BLF147 / MOS FET BLF145

■ High-Speed Automatic Antenna Tuner

Building on the tremendous success of the FT-1000D and FT-1000MP

Elite-Class

HF Transceivers, the MARK-V brings

five exciting new

developments in amateur radio technology.

■

Revolutionary Heat Sink Design for Contest

and DX-pedition Environments

Providing 200 Watts of momentary output from a

compact transceiver enclosure is easy; creating an HF

powerhouse that will pump out full power for days at

a time is tough! Yaesu’ s engineers, seeking to fulfill

the needs of both contest and DX-pedition operators,

have crafted an all-new, highly-efficient " T-configuration "

heat sink for the MARK-V, providing double the heat

dissipating surface area and 2.5 times the cooling capacity

of the heat sink on the FT-1000D! When the going

gets tough, the thermostatically-controlled cross-flow

fan engages at 40 C

ducting the heat across

the dissipating fins and

away from the case. This

revolutionary

new heat

sink design ensures

that the MARK-V will

not let you down, even

under the aggressive

operating circumstances

of an expedition to a

rare tropical island!

II. CLASS-A PA OPERATION: WORLD PREMIERE BY YAESU!

■

Uniquely-Pure Signal Quality, Only from Yaesu!

The MARK-V is the first commercially-designed

Amateur transceiver to provide Class-A operation for

its power amplifier. When engaged by the front panel’ s

[CLASS A] switch, the PA bias is changed dramatically,

and the MARK-V then puts out a 75-Watt signal envelope

of astounding purity. During Class-A operation, 3rd-

order Intermodulation Distortion (IMD) drops from a

typical value of -31 dB to -50 dB or better, and 5th-

and higher-order IMD (the kind which contributes to

"splatter" reports) will drop to the -80 dB range! No

Amateur transceiver has ever approached this degree

of linearity in its power amplifier circuitry. And while

the MARK-V’ s Class-A feature does not directly

affect

your linear

amplifier’s performance,

the extremely clean

drive to your linear will

result in dramatically

cleaner overall signal

reproduction. Be ready

for other stations to

say, "Wow! Your rig

sounds great!"

So as to provide the 30 Volts required by the BLF147 MOSFET PA transistors, as

well as the 13.8 Volts required by other transceiver circuitry, Yaesu’ s engineers

have developed the FP-29 External Power Supply especially for the MARK-V.

The external power supply concept significantly reduces the weight of the transceiver

enclosure itself, providing greater safety when shipping the MARK-V to a DX-

pedition site. The FP-29 is designed with a total output capability of 450 Watts,

with a switching noise suppression of greater than 100 dB, all from an enclosure

measuring just 4.2" (W) x 5.4" (H) x 13.0" (D) (approx. 106 x 136 x 331 mm ).

you like, you can place the FP-29 on a shelf under your operating desk, and enjoy

the compact size of the MARK-V even more!

Separate FP-29 Switching-Regulator Power Supply

T-Configuration Heat Sink

Class A 75W PEP IMD

Class AB 200W PEP IMD

200-Watt

Automatic

Antenna Tuner

Extending the protection afforded the sensitive front-

end components of the receiver, Yaesu’ s engineers

have developed the VRF module: a High-Q input

"Preselector" filter ahead of all active devices in the

front end, including the main bandpass filters! Particularly

in multi-operator contest or DX-pedition environments,

where large low-band antennas may be in close proximity,

a receiver operating (for example) on 20 meters can

suffer intermodulation interference from on-site 40- and

80-meter

signals, compounded

by extremely strong

7 MHz

broadcast signals. The

VRF circuit

provides narrow-

band selectivity

which prevents

this unwanted signal voltage

from hitting the input side of the

bandpass filter switching

diodes,

where 2nd-order IMD is most

often

created in an HF receiver. Tuning of the VRF is

incredibly

simple: just turn the VRF/MEM CH knob,

and peak the background noise or signal strength!

The VRF is stoutly designed, with large (10 mm x 10

mm) coils yielding high Q, and precision tuning

capacitors ensuring that performance does not degrade

over time. A total of 31 tuning memories per band

allow very quick QSY, and the use of high-quality,

shielded relays for VRF selection ensures that nothing

in the VRF can itself contribute IMD.

■ Receiver Front End Highlights

The MARK-V adopts the low-noise front end design

of the FT-1000MP. Two low-noise Junction FET

preamplifiers are provided, one in a "tuned" configuration

with optimized gain and noise figure independently

for the high and low bands, with the other "flat"

preamp providing a wide, uniform-gain response. The

first mixer utilizes a quad of SST-310 Junction FETs

in a doubly-balanced circuit, resulting in wide dynamic

range. Eleven bandpass filter networks provide input

protection for the front end, working in concert with

the VRF to provide the best-ever 2nd-order IMD

prevention in an Amateur transceiver.

IDBT BLOCK DIAGRAM

AF AMP

4th

MIX

3rd

MIX

3rd

LOCAL

2nd

MIX

2nd

LOCAL

1st

MIX

1st

LOCAL

3rd IF

FILTER

2nd IF

FILTER

4th

LOCAL

AGC

DET

455 kHz8.215 MHz

MCF

70.455 MHz

LPF

RF AGC

FRONT END

D/A

EDSP

DET

EDSP

A/D

10.24 kHz

AMP

EDSP

BPF

SHIFT WIDTH

AMP

CPU

IDBT: A Breakthrough in Selectivity!

2.4kHz2.4kHz2.4kHz

III. IDBT: INTERLOCKED DIGITAL BANDWIDTH TRACKING SYSTEM

■

Interlocked Digital Bandwidth Alignment Technique

The MARK-V introduces a unique and formidable

interference-fighting system with the development of

IDBT, whereby the bandwidth of the Digital Signal

Processing filter is automatically locked to be the

sam

as the net bandwidth of the analog IF filters.

Engaging the IDBT, the operator experiences a sudden

sharpening of the shape factor of the receiver’ s filter

system. The analog IF, which utilizes cascaded crysta

and/or mechanical filters, includes both IF WIDTH

and IF SHIFT controls, which allow modification of

the IF passband width and center frequency. With

IDBT, the DSP filter is automatically re-programmed

so as to match the custom bandwidth you just set,

and the DSP filter then contributes a filtering slope

which resembles a sheer cliff! The results? The

incredible selectivity of an all-DSP system with the

protection of the DSP afforded by the extensive IF

analog filtering. What’ s more, the potential for AGC

"pumping" caused by different analog and digital

bandwidths is eliminated; thus, the need for separate

analog and DSP AGC systems is also gone, eliminating

the very real danger of annoying cross-AGC artifacts

which can seriously degrade receiver performance.

New to the 455 kHz analog IF is a 10-Pole Collins

Mechanical SSB Filter, providing outstanding voice

signal reproduction along with enhanced skirt selectivity

compared to the FT-1000MP’ s 8-pole filter.

The IDBT function is controlled by an allocation of

up to 60 kbytes of ROM in the Main CPU, while the

DSP performance utilizes 1 Mbyte of EEPROM!

This perfect blending of the analog and digital worlds

brings you, today’ s Elite-Class operator, the most

crunch-proof receiver filtering ever!

IV. VARIABLE RF FRONT-END FILTER

VRF Preselector Filtering Protects Receiver Front End (160M ~ 20M)■

ATT

IPO ON

LPF

1.8~30MHz

0.1~ 1.8MHz

LPF

BPF

HPF

RF AMP

ANT

VRF/FRONT END BLOCK DIAGRAM

VRF

1st

MIX

1st

LOCAL

RF AGC

LPF

VRF CONTROL

ATT

IPO ON

LPF

1.8~30MHz

0.1~ 1.8MHz

LPF

BPF

HPF

RF AMP

ANT

VRF/FRONT END BLOCK DIAGRAM

VRF

1st

MIX

1st

LOCAL

RF AGC

LPF

VRF CONTROL

ENHANCED ERGONOMICS: MULTI-FUNCTION SHUTTLE JOG DIAL

■

Quick Access to VRF and IDBT via Shuttle Jog Tuning Ring

The immensely-popular Shuttle Jog tuning ring, which

is concentric with the Main Tuning Knob, has a new

look in the MARK-V: it now includes the activation

switches for the VRF (left side)

and IDBT (right side) features, so the operator does

not have to move his hand position to activate these

important circuits during contest or pile-up situations!

■Superb Ergonomics Across the Front Panel

Both the Main and Sub VFO Tuning Knobs are larger,

allowing silky-smooth tuning even if you have large

fingers! The right side

of the front panel contains the adjustment controls for

the VRF, IDBT, NOTCH, and CLARIFIER, conveniently

grouped so you can get at them quickly. For contest

or DX-pedition use, you cannot afford to lose even

milliseconds

in search of

frequently-used control.

And the most popular

EDSP functions from

the

FT-1000MP are now

much

easier to use! The CW Audio

Peaking Filter (with

bandwidths of 60, 120,

and 240 Hz) and the four-

position EDSP Noise

Reduction (NR) feature

are conveniently located

just to the left of the Main

Tuning Dial, for quick,

convenient push-button

access. Right next to the

APF and NR controls are

the three EDSP response

Contour selections, which

enhance signal-to-noise ratio

by matching the DSP

frequency response to the

unique shape of the

incoming signal envelope.

Access VRF and IDBT Features via Shuttle Jog Dial

VRF Features Large, High-Q

Coils and High-Quality Relays

VRF Typical Bandpass Response (3.5 MHz)

Large-diameter control knobs

make precise adjustments easy!

MARK-V

FT-1000MP

HF 200W ALL MODE TRANSCEIVER

The development of an Elite-Class HF Transceiver is not accomplished in a vacuum.

It is a team effort, drawing on the unique abilities of Yaesu' s Research and Development experts,

our most senior HF Design Engineers, and extensively utilizing the comments

and recommendations of hundreds of DX and contest operators.

Today' s bands demand leading-edge features,

and the MARK-V is without peer when it comes to performance and innovation.

ENHANCED DIGITAL SIGNAL

PROCESSING

■

Highly-Effective Digital Noise Reduction Circuit

Utilizing mathematical algorithms developed after

thousands of hours of on-the-air evaluation, the EDSP

Noise Reduction provides four different Noise Reduction

patters, to allow you to cope with changing noise conditions.

The algorithms utilized in the

development of the

EDSP Noise

Reduction cover

the vast majority

noise patterns encountered on the HF bands.

EDSP Unit

■

Optimized Narrow-Bandwidth Filters for CW

and Data Modes

For razor-sharp selectivity under marginal conditions,

the EDSP CW Audio Peaking Filter provides bandwidths

of 60, 120, or 240 Hz. Filter selection is accomplished

using a convenient pushbutton switch on the left side

of the front panel.

START:10Hz STOP:3.1kHz

DRG

SWT

230s

IRG

0dBm

0.0dBmOUTPUT

MKR(250):1.555kHz

A MAG

RBW

10Hz

VBW

100Hz

400ms

NR OFF

NR A

NR B

NR C

NR D

Digital Noise Reduction Performance

Besides the CW Audio Peaking Filter, specially-designed

and optimized digital-mode filters are provided, for

maximum data throughput on RTTY, Packet, SSTV,

PSK31, or FAX.

■ Selectable SSB Pattern-Contour Filters

Particularly effective in enhancing signal-to-noise

ratio and intelligence recovery

on SSB signals, the Contour

selections include High-Cut,

Low-Cut, and Mid-Cut responses,

with a color-coded indicator

aiding

in filter selection.

Choose the one that causers

the incoming voice to "pop"

out of the background noise!

■

Selectable Digital Modulation/Demodulation

CWF 060

CWF 240

CWF 120

10 PMFIR Log Magnitude

FREQUENCY kHz

-10

-20

-30

-40

-50

-60

-70

-80

-90

-100

CW APF Performance

RTTY-LO

OUTPUT: 0.0dBm

SWT:

230s

IRG:

0dBm

RBW:

10Hz

VBW:

100Hz

DRG:

400ms

1400Hz

1420Hz

1500Hz

1210Hz

-6dB

MKR(250):1.555kHz

A : MAG

START : 10Hz STOP : 3.1kHz

PKT

SSTV

FAX

RTTY-HI

1710Hz

DATA BPF Performance

Among EDSP’ s more advanced technology are the

digital Modulator and Demodulator circuits. On transmit,

the EDSP Modulator provides improved transmitter

signal-to-noise ratio, very flat frequency response, and

a choice of four cutoff frequencies (100, 150, 200, or

300 Hz) on the low-frequency side (high-frequency

cutoff: 3100 Hz). Whether you’ re rag-chewing or in a

DX contest, the MARK-V provides a frequency

response that’ s ideal for you!

Providing a boundary for the receiver’ s SSB

bandwidth

within the EDSP, you can select either 100-3100

300-2800 Hz filters in the

EDSP Demodulator circuit,

which

provides very low noise with no odd DSP artifacts

or distortion.

OUTPUT: 0.0dBm

SWT:

230s

IRG:

-20dBm

RBW:

3Hz

VBW:

10Hz

DRG:

400ms

MKR(250):312.53Hz

A : MAG

START : 10Hz STOP : 10kHz

RX-3

RX-1

RX-2

CONTOUR Performance

■ Digital SSB Microphone Equalizer &

RF Speech Processor

Similar in concept to the "Contour" feature used on

receive, one of the four different microphone equalization

filters may be engaged so as to provide the most effective,

penetrating audio "punch" for your voice and microphone.

Working to enhance "talk power" even more, the RF

Speech Processor provides a clean increase in average

power output, through a carefully-designed envelope

compression technique proved so successful in the

FT-1000MP.

OUTPUT: 0.0dBm

SWT:

230s

IRG:

0dBm

RBW:

3Hz

VBW:

10Hz

DRG:

400ms

MKR(250):312.53Hz

A : MAG

START : 10Hz STOP : 10kHz

TX-EQ1

TX-EQ3

TX-EQ2

TX-EQ4

Microphone Equalizer Performance

■ Digital Auto-Notch

The DSP Auto-Notch seeks out and reduces or eliminates

annoying "beat" signals that can ruin reception. Especially

effective when used in a "combined" mode

with the

455 kHz IF Notch (which typically provides rejection

in excess of 70 dB!), the Digital Auto-Notch is a tremendous

aid in providing operator comfort during

long operating

sessions.

DUAL RECEIVE WITH

INDEPENDENT AGC SYSTEMS

■ Listen to Two Frequencies Simultaneously

with No AGC Interaction!

On some "Dual Receive" transceivers, the AGC corresponding

to the signals present on the "Main" frequency affect

what’ s happening on the "secondary" frequency (which

can cause a signal to disappear on the 2nd frequency!).

The MARK-V utilizes two completely independent

receivers, each with its own IF filter(s) and AGC loops,

so that you can listen to two frequencies (on the same

band) simultaneously with no interaction.

The audio levels

for the two receivers may be adjusted

independently, of course, and you can select either

Stereo", "Mixed" (partially combined), or "Monaural"

(fully combined) audio for your headphones. And the

AF-REV switch allows the functions of the AF GAIN

(Main) and the SUB AF volume controls to be reversed,

if desired.

Ideal for contest operation (for watching for "multipliers")

or for DX pile-up use (for monitoring both sides of

the pile-up), the MARK-V’s Dual Receive system

ensures that you’ re always on top of the action!

SPEAKER

AF OUT

AMP

ATT BPF MIX

LEVEL

POTENTIOMETER

SUB

RECEIVER

MAIN

RECEIVER

HYBRID

TRANSFORMER

HEADPHONES

DUAL RECEIVE BLOCK DIAGRAM

LEVEL

POTENTIOMETER

Acclaimed by DX operators worldwide for its wide-

ranging capabilities, Yaesu' s Enhanced Digital

Signal Processing (EDSP) circuitry is a key component

in the

system-wide

filtering

effort which

stretches

from the

antenna ports

to the

microphone or speaker.

ANTENNA

When seconds count in a DX pile-up, the convenience

of the MARK-V’s "SPLIT" operating mode can’t be

beat!

The "RX" (green) and "TX" (red) LEDs above the

Main

and Sub VFO tuning dials are actually combination

LED/

Switches; pressing the Sub VFO’s "TX" LED

automatically

shifts the transmitter to control by the

Sub VFO, with receiver control still on the Main

VFO. Pressing the Sub VFO’s "RX" LED activates

Dual Receive, so you’re listening on both VFOs,

while transmitting on the Sub VFO. It’s easy, it’s

intuitive, and it’s quick!

The wide variations in noise and signal levels on the

HF bands demand a customized approach to receiver

front end gain. The MARK-V provides separate, optimized

preamplifiers for the Low (7 MHz and below), Mid

(10 ~ 21 MHz), and High (24.89 MHz and up) HF

bands. If front end preamplification is not needed,

pressing the IPO (Intercept Point Optimization)

button will bypass the RF preamp stage, routing the

RF energy directly to the first mixer, and increasing

the 3rd-order

Intercept Point

accordingly.

The "A" and "B" antenna jacks allow connection of

different antennas, which may be selected using the

front panel’s A/B switch. The antenna selected on

a particular VFO/memory and band will be preserved

in that VFO or memory register, and will be automatically

ecalled when you return to that VFO or memory. The RX

In" and "Out" jacks allow connection of a Beverage

or loop receiving antenna, and may also be used to

connect a special receive-line filter, if desired.

For precise setting of the background noise level, or

for modifying the receiver’ s AGC threshold, the front

panel’ s RF GAIN control is conveniently located on

the same shaft as the main receiver’ s AF GAIN control.

ANT A ANT B

RX ONLY ANTENNA

FIX ANT JACK

FILTER OR

PREAMP

RX ON

RX OFF

EXT RCVR

OUT

Photo shows optional MD-100A8X Deluxe Desk Microphone

■ Easy-Access "SPLIT" Operation

INDUSTRY-LEADING RF FRONT

END DESIGN

■

Two TX/RX Antenna Ports plus Receive-only

Antenna Line Jacks

■ Three RF Preamplifier Modes plus IPO

(Direct Mixer Feed)

■

Four-Level Input RF Attenuator

For fine-tuning the front-end gain, or for comfortable

listening to extremely strong local signals, the Attenuator

circuit provides 6/12/18 dB of gain reduction (plus "Off").

■ RF GAIN Control

■

AUTO-AGC

For ease in operation, the "AUTO" AGC mode provides

mode-specific selection of the receiver recovery time

for the Automatic Gain Control system. Manual selections

FAST, SLOW, and OFF are also provided.

As the world enters a new millennium,

new chapter in the history books, with

DX-pedition and Contest operators alike have

acclaimed the strong-signal performance

and antenna selection convenience of the

FT-1000D/FT-1000MP. This legacy is

renewed in the MARK-V FT-1000MP!

ANTENNA SWITCHING

MODE

BAND

WIDTH

2nd IF

(8.2MHz)

2.4kHz

THRU

2.4kHz

3rd IF

(455kHz) 2nd IF

(8.2MHz) 3rd IF

(455kHz) 2nd IF

(8.2MHz) 3rd IF

(455kHz)

NOR NAR1 NAR2

(NOR) (NAR1) (NAR2)

■ Factory-installed IF Filter Selections

MODE

BAND

WIDTH

3rd IF

(455kHz)

6.0kHz

2.0kHz

(YF-110SN)

6.0kHz

2.0kHz

(YF-110SN)

2nd IF

(8.2MHz)

THRU

2.0kHz

(YF-114SN)

THRU

2.0kHz

(YF-114SN)

2nd IF

(8.2MHz)

2.4kHz

500Hz

2.4kHz

500Hz

3rd IF

(455kHz)

2.4kHz

500Hz

(YF-115C)

2.4kHz

500Hz

(YF-115C)

2nd IF

(8.2MHz)

2.0kHz

(YF-114SN)

250Hz

(YF-114CN)

2.0kHz

(YF-114SN)

250Hz

(YF-114CN)

3rd IF

(455kHz)

2.0kHz

(YF-110SN)

250Hz

(YF-110CN)

2.0kHz

(YF-110SN)

250Hz

(YF-110CN)

NOR NAR1 NAR2

(NOR) (NAR1) (NAR2)

■ IF Filter Selections with All Options Installed

※On FM, the Bandwidth switches are disabled.

SSB

RTTY

PKT

(LSB)

SSB

RTTY

PKT

(LSB)

New

10-pole Collins Mechanical SSB Filter Passband Response

FT-1000MP

MARK-V

HF 200W ALL MODE TRANSCEIVER

2.4kHz

6.0kHz

2.4kHz

500Hz

2.4kHz

500Hz

2.4kHz

10 PMFIR Log Magnitude

FREQUENCY kHz

-10

-20

-30

-40

-50

-60

-70

-80

-90

-100

OUTSTANDING IF FILTER CHAIN

■

Carefully-Specified 8.2 MHz and 455 kHz IF Filters

Both 2.4 kHz and 500 Hz 8-pole crystal filters for the

2nd (8.2 MHz) IF are factory installed, and the 455 kHz

(3rd) IF includes a 10-pole Collins Mechanical SSB

Filter. Optional filters are available at bandwidths of

2.0 kHz or 250 Hz (2nd and 3rd IFs), and 500 Hz (3rd IF

and Sub Receiver). The outstanding shape factors of

these filters combine with the IDBT digital filtering

to provide brick-wall selectivity with outstanding

close-in performance.

IF Filter Bandwidth Selections

IF Notch Filter Performance

■

455 kHz IF NOTCH features Improved Rejection

The newly-designed 455 kHz IF Notch Filter provides

improved beat rejection, typically 50 dB or more. Use

the front-panel NOTCH control to adjust the exact

position of the Notch.

The MARK-V may be configured (via the convenient

Menu system) to engage both the manual IF Notch Filter

and the DSP Auto-Notch Filter, allowing cascaded

Analog/Digital Notch Filtering. Say "Good-bye" to

irritating beatnotes forever!

■ Dual-Mode IF Noise Blanker

The adjustable IF Noise Blanker may be configured

for optimum blanking of (A) narrow-pulse ignition-type

noises, or (B) wide-pulse over-the-horizon radar systems.

■

Synchronous AM Detection for Reduced Fading

The "Synchronous" detection technique provides improved

AM reception by significantly reducing fading. The

incoming signal is removed, reception is converted to

SSB, and a non-fading carrier is re-inserted, thereby

eliminating the chief cause of fading. A Synchronous

Tuning Scale on the display assists in the tuning process.

Yaesu is proud to turn the page to an exciting

the release of the MARK-V FT-1000MP!

Yaesu’s hybrid Analog/DSP IF design reflects

our commitment to bring you the toughest,

most QRM-resistant receiver possible!

The ultra-fast response time of the Direct Digital

Synthesizer (DDS) allows full break-in (QSK) operation,

without perceptible character truncation. The built-in

electronic keyer features separate Dot:Space and

Dash:Space weight settings, and the receiver recovery

time during semi-break-in work may be set optimally

for CW, independently from the SSB "VOX Delay"

setting.

Owners of Yaesu’ s FT-1000 family of Elite-Class

transceivers use them under the most stressful conditions.

Over long hours of operation, the carefully designed

front-panel ergonomics are a profound asset for the

operator, whether on a DX-pedition on a faraway island or

at home at 4 o’ clock in the morning. Borrowing extensively

from the FT-1000MP front panel layout, the MARK-V

features larger knobs, reduction in the total knob/button

count, and enhanced ease of operation as a result of

the intensive ergonomic system analysis

applied by

Yaesu’ s engineers. This effort, coupled with

feedback

from users like you, has resulted in an incredibly

complex transceiver also being incredibly easy to use!

Select filter center frequency, TX offset, and

Sidetone pitch over the range 300-1050 Hz, and use

the SPOT switch to zero in on the other station.

■

CW Reverse Tuning

Choose either USB- or LSB-side injection to combat

interference, or to switch a station from SSB to CW

without guesswork as to the operating frequency!

■ CW Tuning Indicator

Provides visual confirmation of precise tuning on receive.

Align yourself precisely with the station being worked

by the DX

station in a

pile-up.

The convenient 10-key direct frequency entry keypad

provides instant frequency setting anywhere within the

range of the transceiver. The "Band" keys on the keypad

also provide one-touch band change, and the two VFOs

available per amateur band allow one VFO to be set for the

CW segment, and the other for the phone segment, with the

mode, bandwidth, and antenna selections for each segment

being automatically memorized

into each VFO register.

Yaesu pioneered the use of the DDS (Direct Digital

Synthesizer) in modern HF transceivers, and the MARK-V’ s

DDS system is the latest, greatest evolution of this

design technique. The DDS provides ultra-fine tuning

steps as small as 0.625 Hz,

ideal for the slow

tuning

needed for HF digital

work.

And the very low noise of

the DDS-based local oscillator

system yields

a very low

noise floor during

reception

and transmission.

The MARK-V’ s multi-function display provides a

wealth

of transceiver status in a conveniently-arranged

layout,

and it boasts improved contrast compared to

previous designs. The area around the Main VFO

frequency

display contains the most-often-used

information, such

as Clarifier Offset, VRF Tuning

Scale, Antenna

Tuner

status, and

VFO /

Memory

status.

CW FEATURES FOR OPERATORS

DEMANDING THE BEST

■

CW Full Break-in and Electronic Keyer

■ CW Spot

■

CW Pitch

■ Two Key Jacks

Front- and rear-panel paralleled KEY jacks allow easy

connection to paddles, external electronic keyers, or

computer-driven keying interfaces.

■ Electronic Memory Keyer

Use the optional FH-1 Remote Keypad (or build your

own keypad) to activate the onboard electronic message

memory keyer. Four messages of up to 50 characters

each may be programmed, and an incrementing contest

number may also be imbedded into a recorded message.

CONVENIENCE FEATURES FOR

WORLD-CLASS HF OPERATORS

■

Unmatched Ergonomic Front Panel Design Concept

■

Multi-Function Display with Improved Contrast

■

High-Resolution DDS Provides Silky-Smooth Tuning

■ Enhanced Shuttle Jog™ Tuning Dial

Instantly popular on the original FT-1000MP, the Shuttle

Jog

dial, concentric with the Main VFO tuning dial,

is a spring-loaded center-off tuning aid which allows

the operator to make progressively larger scans up and

down the band by "leaning" on the Shuttle JogTM to

the

left or right. A slight displacement of the dial causes

tuning in 10 Hz steps, and full rotation of the dial to

the left or right yields steps as large as 100 kHz per

step-you’ ll watch the Megahertz fly by if you need to

QSY quickly! The Shuttle JogTM tuning speed may be

adjusted via the Menu system, so you can set it up

just the way you want it! And with the addition of the

VRF and IDBT On/Off switches on the Shuttle JogTM

ring, you’ ll find little need for your hand from the

central area of the transceiver during critical moments!

■ VRF/MEM Channel Selector

The VRF/MEM Channel Selector knob, located in the

upper right-hand corner of the front panel, also functions

as a VFO Channel Selector for quick and easy QSY in

user-programmer steps of 1 to 100 kHz. Use 1 kHz to

5 kHz steps for cruising up and down the band, or 50 kHz

steps for general-coverage frequency hopping. A simple

press on this control restores VRF (Preselector)

operation, and you’ ll be ready for action!

■ Direct Keypad Frequency Entry;

Twin Stacked VFO Registers

■ Feature Customization Menu

For configuration of the MARK-V just the way you want

it, many "set and forget" features and functions may be

customized via the Menu system. The Menu provides

access to the settings for a number of operating parameters

which are not needed during everyday operation; the

use of the Menu technique significantly reduces the

total number of knobs and switches on the front panel,

making long hours of operation even more enjoyable.

■ Extensive Memory System, including

5-Channel Quick Memory Bank (QMB)

The MARK-V provides 99 regular memory channels,

five QMB memories, and nine "band limit" memories.

The "regular" memories may be assigned into one of

five memory "groups", for

convenience in recalling of the

memories. Besides the operating

frequency,

memory channels store

operating mode, antenna selection,

Clarifier offset (if any), IF filter

selection, and

repeater shift status

(if applicable).

■ Versatile Scanning Capability

The acclaimed scanning features of the MARK-V

include

a number of capabilities which make HF

operation a breeze. These include:

●

Memory/VFO Scan: Scan the memories, or scan the

band, with the scanning speed being adjustable, via

Menu, independently for Memory and VFO Scan. An

Auto-Write feature allows "busy" channels to be written

into memory automatically, if desired.

●Memory Channel "Skip" Scanning: You can "flag"

certain memories to be skipped during scanning, so

the transceiver is not constantly halting on constantly-

busy frequencies like WWV.

●Programmable Memory Scan (PMS): You may use

and scanning. For example, within the 18.0-18.5 MHz

range, you may limit operation to the range 18.068

to 18.168 MHz, to prevent accidental excursions

outside the amateur band segment.

■ Easy Digital-Mode Interfacing

The exciting world of digital mode operation is more

popular than ever! And the MARK-V is unmatched

in its ease of interfacing, whether you’ re interested in

PSK-31, RTTY, Packet, SSTV, or Fax. Dedicated

rear-panel FSK and AFSK jacks make cabling a

breeze, and customized EDSP and IF filter selections

make sure that you’ re never forced to use a non-optimal

bandwidth during digital operation.

■ Built-in Temperature-Compensated

Reference Oscillator

The TCXO-4 Temperature-Compensated Reference

Oscillator, which was an extra-cost option on the

original FT-1000MP, is built into every MARK-V.

The TCXO-4 provides frequency accuracy of 0.5 ppm

at 25 C, and 2.0 ppm over the temperature range -10 C to

+50 C. For ultra-precise

frequency accuracy,

the optional TCXO-6

provides accuracy of

0.25 ppm at 25 C,

and 0.5 ppm at -10 C

to +50

AND SO MUCH MORE

●General Coverage Reception: 100 kHz ~ 30 MHz.

●Large, high-quality speaker (3-5/8" / 92 mm) for

better receive audio clarity. ●Two headphone jacks:

one each 6 and 3.5 mm. ●Adjustable "Beep" tone for

keypad keys. ●Adjustable torque for tuning

knobs.

●

Built-in VOX. ●FAST tuning key for quick

frequency change. ●Built-in RS-232C level converter

for easy computer interfacing.

The FT-1000D and FT-1000MP were

universally acclaimed, not only for

their industry-leading RF and IF

innovations, but also for the wealth

operating conveniences made available to

demanding HF operators. The MARK-V

FT-1000MP builds on

this tradition, and

makes it even better!

About this brochure: we have made this brochure as comprehensive and factual as possible. We reserve the right, however, to make changes at any time in equipment, optional accessories,

specifications, model numbers, and availability. Some accessories shown herein may not be available in some countries. Some information may have been updated since the time of printing;

please check with your Authorized Yaesu Dealer for complete details.

B9200290

Remote Control Keypad

FH-1

DVS-2

Digital Voice Recorder

SSB 2.0 kHz X'tal Filter

YF-114SN

CW 250 Hz X'tal Filter

YF-114CN

SSB 2.0 kHz X'tal Filter

YF-110SN

CW 250 Hz X'tal Filter

YF-110CN

CW 500 Hz Filter

(Collins Mechanical Filter)

YF-115C

*For Main Rcvr and 2nd IF Sub Rcvr

Temperature

Compensated X'tal

TCXO-6

Desktop Microphone

MD-100A8X

External Speaker w/Audio Filters

SP-8

Hand Microphone

MH-31B8

2nd IF (8.2 MHz) Filters 3rd IF (455 kHz) Filters

RX Frequency Range : 100 kHz ~ 30 MHz

TX Frequency Ranges : 160 ~10 m

(Amateur bands only)

Frequency Stability :

± 0.5 ppm (after 1 min. @ 25 C)

± 0.25 ppm

(after 1 min. @ 25

, w/TCXO-6)

Operating Temperature Range: -10

~ +50

Emission Modes :

LSB, USB, CW, FSK, AFSK, AM, FM

Frequency Steps : 0.625/1.25/2.5/5/10 Hz for

SSB,CW, RTTY & Packet

100 Hz for AM and FM

Antenna Impedance : 16.6~150 Ohms, unbalanced

(Tuner ON, TX only)

Power Consumption : 13.8 VDC 30 VDC

RX (no signal) 2.3 A –

RX (signal) 2.7 A –

TX (200 W) 2.2 A 14.5 A

Supply Voltage : 30 VDC and 13.8 VDC (FP-29)

Dimensions (WHD) : 16 "x 5.3 "x 13.7 "

(410 x 135 x 347 mm)

Weight (approx.) : 31 lbs. (14 kg.)

Power Output : Adjustable up to 200 watts

(50 watts AM carrier),

Class A mode (SSB) : 75 watts maximum

Duty Cycle : 100% @ 100 watts,

50% @ 200 watts

(FM & RTTY, 3-minute TX)

Modulation Types: SSB: J3E Balanced,

AM: A3E Low-level (early stage),

FM: F3E Variable reactance,

AFSK : J1D, J2D Audio frequency shift keying

Maximum FM Deviation

: ± 2.5 kHz

FSK Shift Frequencies:

170, 425, and 850 Hz

Packet Shift Frequencies:

200 and 1000 Hz

Harmonic Radiation : Better than -60 dB (Typical)

SSB Carrier Suppression

: At least 40 dB below peak output

Undesired Sideband Suppression

: At least 55 dB below peak output

Audio Response (SSB)

: Not more than -6 dB

from 400 to 2600 Hz

3rd-order IMD: - 31 dB @ 200 watts PEP, or better

(Class A mode) - 50 dB @ 75 watts PEP (Typical)

Microphone Impedance:

500 to 600 Ohms

Circuit Type

Quad-conversion superheterodyne

(triple conversion for FM)

Intermediate Frequencies:

Main RX; 70.455 MHz/8.215 MHz/455 kHz,

Sub RX; 47.21 MHz/455 kHz

Sensitivity : Modes

0.5 - 1.8 MHz 1.8 - 30 MHz

SSB/CW (2.0 kHz)

2 μV 0.16 μV

AM (6 kHz) 13 μV 2 μV

FM – 0.5 μV

(with preamp on, IDBT on, SSB/CW/AM for 10 dB S/N,

FM for 12 dB SINAD, 0 dBμ = 1 μV)

Selectivity (-6/-60 dB):

BandWidth

Modes

Min. -6 dB BW Max. -60 dB BW

2.4 kHz all except FM 2.2 kHz 4.2 kHz

2.0 kHz all except FM 1.8 kHz 3.6 kHz

500 Hz

CW/RTTY/Packet

500 Hz 1.8 kHz

250 Hz

CW/RTTY/Packet

250 Hz 700 Hz

AM (Wide) 4 kHz 14 kHz

FM 8 kHz 19 kHz

IF Rejection (1.8 ~ 30 MHz):

80 dB or better (Main RX), 60 dB or better (Sub Rx)

Image Rejection (1.8 ~ 30 MHz):

80 dB or better (Main), 50 dB or better (Sub)

Maximum Audio Output:

2.0 W into 4 Ohms with <10 %

THD

Linear Amplifier/48 Volts DC Power Supply

OPTIONAL ACCESSORIES

SPECIFICATIONS

General Transmitter Receiver

Specifications are subject to change, in the interest of technical

improvement, without notice or obligation.

DC Output Voltage/Current: +30 V: 15 A; +13.8 V: 3 A

Input Voltage : AC 100-120 V, 50-60 Hz

AC 200-240 V, 50-60 Hz

Current Consumption (Approx.): AC 100-120 V: 9 A, AC 200-240 V: 5 A

Operating Temperature Range

: -10 C~ +50 C

Case Size (W x H x D):

4.2 "x 5.3 " x 13 " (

106 x 135.5 x 331 mm

)

Weight (Approx.): 7 lbs.(3.2 kg.)

FP-29 Specifications

Lightweight

Stereo Headphone

YH-77STA LL-7 Phone Patch Option

2000.06NS Printed in Japan

VERTEX STANDARD CO., LTD.

For the latest Yaesu news,visit us on the Internet:

4-8-8 Nakameguro, Meguro-ku, Tokyo 153-8644, Japan

VERTEX STANDARD

US Headquarters

17210 Edwards Road, Cerritos, CA 90703, U.S.A.

International Division

8350 N.W. 52nd Terrace, Suite 201, Miami, FL 33166, U.S.A.

YAESU EUROPE B.V.

P.O. Box 75525 1118 ZN, Schiphol The Netherlands

YAESU UK LTD.

Unit 12, Sun Valley Business Park, Winnall Close

Winchester, Hampshire, SO23 0LB, U.K.

VERTEX STANDARD HK LTD.

Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road,

Kwun Tong, Kowloon, Hong Kong

http://www.vxstdusa.com http://www.yaesu.co.uk

Phone 562/404-2700; Fax 562/404-1210

Email:amateursales@vxstdusa.com

Email: sales@yaesu.co.uk

YAESU FT 1000MP MARK V Brochure

Navigation menu

Versions of this User Manual:

Views

Navigation