Mininet Wifi Manual
User Manual: Pdf
Open the PDF directly: View PDF .
Page Count: 70
Download | ![]() |
Open PDF In Browser | View PDF |
The User Manual 2 Ramon dos Reis Fontes and Christian Esteve Rothenberg I NFORMATION & N ETWORKING T ECHNOLOGIES R ESEARCH & I NNOVATION G ROUP (INTRIG) D EPARTMENT OF C OMPUTER E NGINEERING AND I NDUSTRIAL AUTOMATION (DCA) S CHOOL OF E LECTRICAL AND C OMPUTER E NGINEERING (FEEC) U NIVERSITY OF C AMPINAS (UNICAMP) - B RAZIL GITHUB . COM / INTRIG - UNICAMP / MININET- WIFI Mininet-WiFi is being developed as a clean extension of the high-fidelity Mininet emulator by adding the new abstractions and classes to support wireless NICs and emulated links while conserving all native lightweight virtualization and OpenFlow/SDN features. January 2018 Contents 1 About Mininet-WiFi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1.1 Requirements 9 1.2 Installing Mininet-WiFi 9 1.2.1 1.2.2 GitHub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Docker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 1.3 Limitations 10 1.4 Architecture and Components 10 1.4.1 1.4.2 Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Classes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 1.5 Wireless medium emulation 1.5.1 1.5.2 Traffic Control (TC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Wmediumd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 1.6 Creating Network 1.6.1 1.6.2 1.6.3 1.6.4 Changing Topology Size and Type Examples . . . . . . . . . . . . . . . . . . . . Getting information . . . . . . . . . . . . Changes at runtime . . . . . . . . . . . . 1.7 Supported Features 1.7.1 1.7.2 1.7.3 1.7.4 1.7.5 1.7.6 Encryption . . . . . . . . . . . . . . . . . . . . . . . . . . Support to IEEE 802.11r . . . . . . . . . . . . . . . . . Support to IEEE 8021x . . . . . . . . . . . . . . . . . . Support to bgscan (Background scanning) Using 4-address for AP and client mode . . . Interference . . . . . . . . . . . . . . . . . . . . . . . . . 12 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 15 15 16 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 16 17 17 17 18 1.7.7 1.7.8 Multiple SSIDs over a single AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Support to Virtual Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 1.8 Videos 19 1.9 Contact Us 19 1.10 FAQ 19 2 Mobility Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 2.1 Mobility Models Supported 21 2.2 How to setup Mobility? 21 3 Propagation Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 3.1 Propagation Models Supported 23 3.2 How to add specific Propagation Model? 23 4 Replaying Traces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 4.1 Replaying Mobility 25 4.2 Replaying Bandwidth 25 4.3 Replaying RSSI 25 5 Tutorial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 5.1 Introduction 5.2 First ideas 5.2.1 5.2.2 5.2.3 5.2.4 5.2.5 5.2.6 5.2.7 5.2.8 How to read this post . . . . . . . . . . . . . . . Mininet-WiFi compared to Mininet . . . . Mininet-WiFi and Mobility . . . . . . . . . . . . 802.11 Wireless LAN Emulation . . . . . . . . Mininet-WiFi display graph . . . . . . . . . . . Install Mininet-WiFi on a Virtual Machine Set up a new Ubuntu Server VM . . . . . . Set up the Mininet-WiFi VM . . . . . . . . . . 5.3 Mininet-WiFi Tutorial #1: One access point 5.3.1 5.3.2 5.3.3 Capturing Wireless control traffic in Mininet-WiFi . . . . . . . . . . . . . . . . . . . . . . . . . 30 Wireless Access Points and OpenFlow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Stop the tutorial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 5.4 Mininet-WiFi Tutorial #2: Multiple access points 5.4.1 5.4.2 5.4.3 A simple mobility scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 OpenFlow flows in a mobility scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Stop the tutorial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 27 27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 28 28 29 29 29 29 30 30 33 5.5 Mininet-WiFi Tutorial #3: Python API and scripts 5.5.1 5.5.2 5.5.3 5.5.4 5.5.5 5.5.6 5.5.7 5.5.8 5.5.9 5.5.10 5.5.11 5.5.12 5.5.13 5.5.14 The Mininet-WiFi Python API . . . . . . . . . . Basic station and access point methods Classic Mininet API . . . . . . . . . . . . . . . . . Example . . . . . . . . . . . . . . . . . . . . . . . . Working at runtime . . . . . . . . . . . . . . . . Mininet-WiFi CLI . . . . . . . . . . . . . . . . . . . Position . . . . . . . . . . . . . . . . . . . . . . . . . . Distance . . . . . . . . . . . . . . . . . . . . . . . . . Mininet-WiFi Python runtime interpreter . Getting network information . . . . . . . . . Changing the network during runtime . Running commands in nodes . . . . . . . . Mininet-WiFi and shell commands . . . . . Stop the tutorial . . . . . . . . . . . . . . . . . . . 5.6 Mininet-WiFi Tutorial #4: Mobility 5.6.1 5.6.2 5.6.3 5.6.4 5.6.5 5.6.6 Python API and mobility . . . . . . . Moving a station in virtual space Re-starting the scenario . . . . . . . More Python functions . . . . . . . . Test with iperf . . . . . . . . . . . . . . . Stop the tutorial . . . . . . . . . . . . . 5.7 Mininet-WiFi Tutorial #5: VANETs (Veicular Ad Hoc Networks) 5.7.1 5.7.2 5.7.3 Python API . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Node Car Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Integration with SUMO (Simulation of Urban Mobility) . . . . . . . . . . . . . . . . . . . . . 53 5.8 Mininet-WiFi example scripts 53 5.9 Conclusion 53 6 Guided exercises/demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 6.1 Guided exercises/demo 6.1.1 6.1.2 6.1.3 Activity 1: Warming up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Activity 2: Loading Network Topologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Activity 3: Customizing the Wireless Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 6.2 Further hands-on 6.2.1 6.2.2 Activity 4: Mobility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Activity 5: Received Signal Strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 6.3 OpenFlow 6.3.1 Activity 6: Mobility and OpenFlow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 7 Reproducible Research . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 7.1 SwitchOn 2015 . . . . . . . . . . . . 41 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 41 42 43 44 44 45 45 45 45 46 46 47 47 47 . . . . . . . . . . . . . . . . . . . . . . . . 48 49 50 51 51 51 51 55 57 58 59 8 7.2 SBRC 2016 7.2.1 7.2.2 7.2.3 7.2.4 7.2.5 7.2.6 Case 1 - Simple test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Case 2 (1/2) - Communication among stations and hosts/Verifying flow table Case 2 (2/2) - Changing the controller (from reference to external controller) Case 3 - Handover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Case 4 - Changes at runtime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Case 5 - Bridging physical and virtual emulated environments . . . . . . . . . . . . 59 7.3 SIGCOMM 2016 7.4 From Theory to Experimental Evaluation: Resource Management in SoftwareDefined Vehicular Networks 62 7.5 The Computer Journal - How far can we go? Towards Realistic SoftwareDefined Wireless Networking Experiments 62 7.5.1 7.5.2 7.5.3 7.5.4 7.5.5 7.5.6 7.5.7 Wireless n-Casting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Multipath TCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hybrid Physical-Virtual Environment . . . . . . . . . . . . . . . . . . SSID-based Flow Abstraction . . . . . . . . . . . . . . . . . . . . . . . . EXPERIMENTAL VALIDATION: Propagation Model . . . . . . . . . EXPERIMENTAL VALIDATION: Simple File Transfer . . . . . . . . . EXPERIMENTAL VALIDATION: Replaying Network Conditions 8 Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 8.1 SDN For Wireless 2015 65 8.2 CNSM 2015 - Best Paper Award! 65 8.3 SwitchOn 2015 65 8.4 SBRC 2016 65 8.5 SIGCOMM 2016 66 8.6 Institute of Electrical and Electronics Engineers - IEEE 2017 66 8.7 The Computer Journal 2017 66 9 Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 10 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 10.1 handover.py . . . . . . 60 60 60 60 60 61 61 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 63 63 63 63 63 63 69 1. About Mininet-WiFi Mininet-WiFi is a fork of the Mininet SDN network emulator and extended the functionality of Mininet by adding virtualized WiFi stations and access points based on the standard Linux wireless drivers and the 80211_hwsim wireless simulation driver. We added classes to support the addition of these wireless devices in a Mininet network scenario and to emulate the attributes of a mobile station such as position and movement relative to the access points. The Mininet-WiFi extended the base Mininet code by adding or modifying classes and scripts. So, Mininet-WiFi adds new functionality and still supports all the normal SDN emulation capabilities of the standard Mininet network emulator. 1.1 Requirements Mininet-WiFi should work fine in any Ubuntu Distribution from 14.04. 1.2 1.2.1 Installing Mininet-WiFi GitHub You have to follow only for 4 steps to install Mininet-WiFi: • sudo apt-get install git • git clone https://github.com/intrig-unicamp/mininet-wifi • cd mininet-wifi • sudo util/install.sh -Wlnfv Mininet WiFi is installed by a script. Run the script with the -h help option to see all the options available. wifi:~$ util/install.sh -h Chapter 1. About Mininet-WiFi ofprotocol controller Hostapd Mininet-WiFi nl80211 User Space Kernel Space station sta1 namespace station sta2 namespace root ap1 namespace sta1-wlan0 sta2-wlan0 ap1-wlan0 Mobility Models ofdatapath wpa_supplicant iw iwconfig Propagation Models 10 TC tool and Wmediumd MLME AP mode Configuration Configuration management management for for wireless wireless devices devices wlan1 wlan2 wlan3 cfg80211 MLME station mode Creates Virtual WiFi Interfaces mac80211_hwsim mac80211 Provides MLME management services with which drivers can be developed to support softMAC Figure 1.1: Mininet-WiFi Components. 1.2.2 1.3 Docker Mininet-WiFi is available on Docker1 . Limitations Mininet-WiFi inherits all limitations of Mininet, including: • You cannot handle with packets that go out to the incoming port with the OpenFlow protocol. 1.4 Architecture and Components The main components that make part of the development of Mininet-WiFi are illustrated in Figure 1.1. In the kernel-space the module mac80211_hwsim is responsible for creating virtual Wi-Fi interfaces, important for stations and access points. Continuing in the kernel-space, MLME (Media Access Control Sublayer Management Entity)2 is realized in the stations side, while in the user-space the hostapd is responsible for this task in the AP side. Mininet-WiFi also uses a couple utilities such as iw, iwconfig e o wpa_supplicant. The first two are used for interface configuration and for getting information from wireless interfaces and the last one is used with Hostapd, in order to support WPA (Wi-Fi Protected Access), among other things. Besides them, another fundamental utility is TC (Traffic Control). The TC is an user-space utility program used to configure the Linux kernel packet scheduler, responsible for controlling the rate, delay, latency and loss, applying these attributes in virtual interfaces of stations and APs, representing with higher fidelity the behavior of the real world. Figure 1.2 depicts the components and connections in a simple topology with two stations (or hosts) created with Mininet-WiFi, where the newly implemented components (highlighted in gray) are presented along the original Mininet building blocks. Although stations are equipped with a wireless interface by default they are able to connect with access points through wired links (veth pairs) as well. More specifically, we added WiFi interfaces on stations that now are able to connect to an access point through its (wlanX) interface that is bridged to an OpenFlow switch with AP capabilities 1 https://registry.hub.docker.com/u/ramonfontes/mininet-wifi/ 2 some of the functions performed by MLME are authentication, association, sending and receiving beacons, etc. 1.4 Architecture and Components 11 Figure 1.2: Components and connections in a two-host network created with Mininet-WiFi. represented by (ap1). Similar to Mininet, the virtual network is created by placing host processes in Linux OS network namespaces interconnected through virtual Ethernet (veth) pairs. The wireless interfaces to virtualize WiFi devices work on master mode for access points and managed mode for stations. Stations: Are devices that connect to an access point through authentication and association. In our implementation, each station has one wireless card (staX-wlan0 - where X shall be replaced by the number of each station). Since the traditional Mininet hosts are connected to an access point, stations are able to communicate with those hosts. Access Points: Are devices that manage associated stations. Virtualized through hostapd3 daemon and use virtual wireless interfaces for access point and authentication servers. While virtualized access points do not have (yet) APIs allowing users to configure several parameters in the same fashion of a real one, the current implementation covers the most important features, for example ssid, channel, mode, password, cryptography, etc. Both stations and access points use cfg80211 to communicate with the wireless device driver, a Linux 802.11 configuration API that provides communication between stations and mac80211. This framework in turn communicates directly with the WiFi device driver through a netlink socket (or more specifically nl80211) that is used to configure the cfg80211 device and for kernel-user-space communication as well. 1.4.1 Files • • • • • mininet/wifiAssociationControl.py - association Control techniques mininet/wifiLink.py - link details mininet/wifiDevices.py - specification of real devices mininet/wifiMobility.py - mobility parameters mininet/wifiModule.py - module 3 Hostapd (Host Access Point Daemon) user space software capable of turning normal wireless network interface cards into access points and authentication servers Chapter 1. About Mininet-WiFi 12 • • • • 1.4.2 Classes • • • • • • • • • • • 1.5 mininet/wifiPlot.py - graphs mininet/wifiPropagationModels.py - propagation models mininet/wifiReplaying.py - replaying captured traces mininet/vanet.py - VANET networks UserAP(): User-space AP OVSAP(): Open vSwitch AP addHost(): adds a host to a topology and returns the host name addAccessPoint(): adds an access point to a topology and returns the access point name addCar(): adds a car to a topology and returns the car name addPhysicalBaseStation(): attach a physical usb interface to a virtual base station to a topology and returns the physical base station name addStation(): adds a station to a topology and returns the station name addSwitch(): adds a switch to a topology and returns the switch name addLink(): adds a bidirectional link to a topology (and returns a link key, but this is not important). Links in Mininet-WiFi are bidirectional unless noted otherwise. plotGraph(): use this class if you want to plot graph. startMobility: useful when you want to use a mobility model. Wireless medium emulation Mininet-WiFi relies on two approaches for simulating the wireless medium: tc and wmediumd. 1.5.1 Traffic Control (TC) Tc (traffic control) is the user-space utility program used to configure the Linux kernel packet scheduler. Used to configure Traffic Control in the Linux kernel, Traffic Control consists of the following: • Shaping: When traffic is shaped, its rate of transmission is under control. Shaping may be more than lowering the available bandwidth - it is also used to smooth out bursts in traffic for better network behaviour. Shaping occurs on egress. • Scheduling: By scheduling the transmission of packets it is possible to improve interactivity for traffic that needs it while still guaranteeing bandwidth to bulk transfers. Reordering is also called prioritizing, and happens only on egress. • Policing: Where shaping deals with transmission of traffic, policing pertains to traffic arriving. Policing thus occurs on ingress. • Dropping: Traffic exceeding a set bandwidth may also be dropped forthwith, both on ingress and on egress. The aforementioned properties have been used to apply values for bandwidth, loss, latency and delay in Mininet-WiFi. Tc was the first approach adopted in Mininet-WiFi for simulating the wireless medium. Intermediate Functional Block (IFB) Devices There are two modes of traffic shaping: ingress and egress. Ingress handles incoming traffic and egress outgoing traffic. Linux does not support shaping/queuing on ingress, but only policing. 1.5 Wireless medium emulation 13 Therefore IFB exists, which we can attach to the ingress queue while we can add any normal queuing like as egress queue on the IFB device. Intermediate Functional Block (IFB) is an alternative to tc filters for handling ingress traffic, by redirecting it to a virtual interface and treat is as egress traffic. IFB is supported by calling net.useIFB() just after adding all nodes and before calling net.configureWifiNodes(). Further information about IFB is available at http://shorewall.net/traffic_shaping.htm#IFB. Customizing Equations When a node is in motion different values for bandwidth, latency, loss and delay are applied based on equations. Those equations can be customized by calling setChannelEquation(), for instance (it won’t work for mesh/adhoc): #dist = distance between receiver and transmitter #custombw = is a default value for bw which takes into account the RSSI net.setChannelEquation(bw='value.rate * (1.1 ** -dist)', loss='(dist * 2) / ,→ 100', delay='(dist / 10) + 1', latency='2 + dist') 1.5.2 Wmediumd The kernel module mac80211_hwsim uses the same virtual medium for all wireless nodes. This means all nodes are internally in range of each other and they can be discovered in a wireless scan on the virtual interfaces. Mininet-WiFi simulates their position and wireless ranges by assigning stations to other stations or access points and revoking these wireless associations. If wireless interfaces should be isolated from each other (e.g. in adhoc or mesh networks) a solution like wmediumd4 is required. It uses a kind of a dispatcher to permit or deny the transfer of packets from one interface to another. A small helper to support wmediumd was initially developed by Patrick Große5 and it was included in Mininet-WiFi. At the first release It supported two modes: dynamic and static mode. Dynamic mode This mode should be the best choice in most use cases. It requires the input of Mininet-WiFi interfaces as Python objects and retrieves the MAC addresses which are required for wmediumd automatically from the Mininet API. Static mode The static mode uses the MAC addresses that have been provided. In most cases the dynamic mode is the one to use. The advantage of the static mode is that no station objects are required and the data could be provided prior to the start of Mininet-WiFi. Afterwards, support to interference was added. The support to interference improved the helper in such way that wmediumd is able to capture the position of nodes from Mininet-WiFi and it calculates the signal level based on the distance between source and destination by relying on the log distance propagation model. The interference model provided by wmediumd relies on the clear channel assessment (CCA) threshold, which defines a parameter causing interference. 4 https://github.com/bcopeland/wmediumd 5 https://github.com/patgrosse/wmediumd Chapter 1. About Mininet-WiFi 14 The initial idea behind both dynamic and static modes is now discarded since wmediumd can be used when you set enable_wmediumd=True. Installation of wmediumd It is required that wmediumd can be called using the command wmediumd. That means it should be located in /usr/bin or any other path that is available through the PATH enviroment variable. wmediumd can be automatically installed using the -l option on util/install.sh. This will copy the binary to /usr/bin/wmediumd. Installing wmediumd in Mininet-WiFi: sudo util/install.sh -W Traffic control versus Wmediumd Wmediumd has been shown to be the best approach for the simulation of the wireless medium. Some advantages include: • It isolates the wireless interfaces from each other • wmediumd implements backoff algorithm. TC relies only in FIFO queue discipline. • It decides when the association has to be evoked based on the signal level • Values for bandwidth, loss, latency and delay are applied relying in a matrix. This matrix implements an option to determine PER (packet error rate) with outer matrix defined in IEEE 802.11ax. The matrix is defined in Appendix 3 of 11-14-0571-12 TGax Evaluation Methodology6 . • We highly recommend wmediumd for both adhoc and wireless mesh networks. 1.6 Creating Network You can create a simple network (2 stations and 1 access point) with the following command: sudo mn --wifi The command above can be used with other parameters, like in: sudo mn --wifi --ssid=new_ssid --mode=g --channel=1 and also, sudo mn --wifi --position --wmediumd --plot position parameter automatically defines the position of the nodes, whereas wmediumd enables wmediumd (you can find more information about wmediumd along this manual). plot plots a graph. You can also use just mn if you want to work only with Mininet instead of Mininet-WiFi. 1.6.1 Changing Topology Size and Type The default topology is a single Access Point connected to two Stations. You could change this to a different topo with –topo and pass parameters for that topology’s creation. For example, to verify all-pairs ping connectivity with one Access Point and five Stations: sudo mn --wifi --test pingall --topo single,5 6 https://mentor.ieee.org/802.11/dcn/14/11-14-0571-12-00ax-evaluation-methodology.docx 1.6 Creating Network 15 Another example, with a linear topology (where each Access Point has one station, and all Access Points connect in a line via wired media): sudo mn --wifi --test pingall --topo linear,5 1.6.2 Examples If you are just beginning to write scripts for Mininet-WiFi, you can use the example scripts as a starting point. We created example scripts in the /mininet-wifi/examples directory that show how to use most of the features in Mininet-WiFi. 1.6.3 Getting information getting the position: mininet-wifi>py sta1.params['position'] getting AP that a specific station is associated: mininet-wifi>py sta1.params['associatedTo'] getting APs in range: mininet-wifi>py sta1.params['apsInRange'] getting the channel: mininet-wifi>py sta1.params['channel'] getting the frequency: mininet-wifi>py sta1.params['frequency'] getting the mode: mininet-wifi>py sta1.params['mode'] getting the rssi: #not available when wmediumd and interference are enabled. Use iw/iwconfig instead. mininet-wifi>py sta1.params['rssi'] getting the Tx Power: mininet-wifi>py sta1.params['txpower'] getting associated stations to ap1: mininet-wifi>py ap1.params['associatedStations'] Chapter 1. About Mininet-WiFi 16 1.6.4 Changes at runtime setting the position (coord x, y, z): mininet-wifi>py sta1.setPosition('40,20,40') setting up the antenna gain (dBm): mininet-wifi>py sta1.setAntennaGain(5, intf='sta1-wlan0') setting the signal range (meters): mininet-wifi>py sta.setRange(100) mininet-wifi>py sta.setRange(100, intf='sta1-wlan0') setting Tx Power (dBm): mininet-wifi>py sta1.setTxPower(10, intf='sta1-wlan0') setting channel: mininet-wifi>py sta1.setChannel(10, intf='sta1-wlan0') changing association to ap1: mininet-wifi>py sta1.moveAssociationTo(ap1, intf='sta1-wlan0') make interface work as adhoc mode: mininet-wifi>py sta1.setAdhocIface('sta1-wlan0', ssid='my-ssid') make interface work as mesh mode: mininet-wifi>py sta1.setMeshIface('sta1-wlan0', ssid='my-ssid') 1.7 1.7.1 Supported Features Encryption Mininet-WiFi supports all the common wireless security protocols, such as WEP (Wired Equivalent Privacy), WPA (Wi-Fi Protected Access) and WPA2. On both station/ap side the password and encryption type can be set as below: sta1 = net.addStation('sta1', passwd='123456789a', encrypt='wpa2') ap1 = net.addAccessPoint('ap1', ssid="ssid1", mode="g", channel="1", ,→ passwd='123456789a', encrypt='wpa2') Attention! OVS does not support WPA/WPA2 authentication. 1.7.2 Support to IEEE 802.11r The example below enables 802.11r. ap1 = net.addAccessPoint( 'ap1', ... passwd='123456789a', ,→ encrypt='wpa2', ieee80211r='yes', mobility_domain='a1b2' 1.7 Supported Features 1.7.3 17 Support to IEEE 8021x The example below enables 8021x. ap1 = net.addAccessPoint( 'ap1', ... authmode='8021x', encrypt='wpa2', ,→ ...) Further configuration includes radius_server and shared_secret: ap1 = net.addAccessPoint( 'ap1', ... mode='8021x', encrypt='wpa2', ,→ enable_radius='yes', radius_server='127.0.0.1', ,→ shared_secret='secret' ...) 1.7.4 Support to bgscan (Background scanning) wpa_supplicant behavior for background scanning can be specified by configuring a bgscan module. This module is responsible for requesting background scans for the purpose of roaming within an ESS (i.e., within a single network block with all the APs using the same SSID). You can enable bgscan calling setBgscan(), for example: net.setBgscan() or net.setBgscan(module="$module_name", s_inverval=$value, signal=$value, ,→ l_interval=$value, database=$dir) s_interval: short bgscan interval in seconds signal: signal strength threshold l_interval: long interval database:source: https://w1.fi/cgit/hostap/plain/wpa_supplicant/wpa_supplicant.conf 1.7.5 Using 4-address for AP and client mode IEEE 802.11 (WLAN) frames have four address fields in their headers. In order to transport ethernet packets transparently over a Wireless Distribution System (WDS) link, the IEEE 802.3 (Ethernet) frame gets encapsulated in a IEEE 802.11 (WLAN) frame. In this case all of the four address fields are used, for: • sender of the ethernet frame • receiver of the ethernet frame • sender of the WLAN frame • receiver of the WLAN frame Sender and receiver of the ethernet frame are simply copied from the transported ethernet frame. The remaining fields allow the receiver to recognize that the frame is meant for him, and allow it to acknowledge the reception of the frame to the (WLAN) sender. However, usually only three of the four fields are needed, so most drivers don’t know about how to handle frames which make use of all four address fields. In other words: the most important ingredient for WDS is support for 4-address-headers. Chapter 1. About Mininet-WiFi 18 Worth to mention that the 4-address frame format does not itself constitute a wireless distribution system or a wireless DS, it is simply a frame addressing mechanism that allows creation of a multitude of specialized implementations, one of which could be a wireless distribution system. The advantage of this mode compared to regular WDS mode is that it’s easier to configure and does not require a static list of peer MAC addresses on any side. A sample file for 4-address is available at /examples/4address.py. In general, the user must set AP/Client with the param _4addr, for example: ap1 = net.addAccessPoint( 'ap1', _4addr="ap", ssid="ssid1" ... ) ap2 = net.addAccessPoint( 'ap2', _4addr="client", ssid="ssid2" ... ) and then a 4-address link must be created as below: net.addLink(ap1, ap2, link='4addr') 1.7.6 Interference Mininet-WiFi supports the interference model provided by wmediumd. An example about how to enable interference is given below. net = Mininet( ... enable_wmediumd=True, enable_interference=True ) The interference model implemented in wmediumd relies on CCA THRESHOLD (Clear Channel Assessment). The CCA is used by the MAC layer to determine (i) if the channel is clear for transmitting data, and (ii) for determining when there is incoming data. Evaluation of CCA is made by the PHY layer and the resulting assessment is communicated to the MAC layer via the PHY-CCA.indicate service primitive. This primitive can either be set to IDLE, when the channel is assessed to be clear, or BUSY when the channel is assessed to be in use. Optionally, a fadding coefficient is also supported by Mininet-WiFi when wmediumd is enabled: net = Mininet( ... enable_wmediumd=True, enable_interference=True, ,→ fading_coefficient=1 ) Further details about the interference model implemented in wmediumd can be found at the mater thesis titled Medium and mobility behaviour insertion for 802.11 emulated networks. 1.7.7 Multiple SSIDs over a single AP It is very common for an organization to have multiple SSIDs in their wireless network for various purposes, including: (i) to provide different security mechanisms such as WPA2-Enterprise for your employees and an “open” network with a captive portal for guests; (ii) to split bandwidth among different types of service; or (iii) to reduce costs by reducing the amount of physical access points. In Mininet-WiFi, an unique AP supports up to 8 different SSIDs (limitation imposed by mac80211_hwsim). Multiple SSIDs can be configured as below: ap1 = net.addAccessPoint( 'ap1', ssid="ssid1,ssid2,ssid3", mode="g", ,→ channel="1" ) 1.8 Videos 1.7.8 19 Support to Virtual Interfaces The mac80211 subsystem in the linux kernel supports multiple wireless interfaces to be created with one physical wireless card. To do so you have to set the number of virtual interfaces to be created (nvif), as illustrated below. sta1 = net.addStation( 'sta1', nvif=2 ) 1.8 Videos You can find many videos about Mininet-WiFi in a channel on youtube7 . 1.9 Contact Us You are invited to participate of our mailing list8 . 1.10 FAQ • Question: I am getting the following Error message: IndexError: list index out of range. How to solve it? Answer: sudo mn -c • Question: Is it possible to create a wired link between station and ap? Answer: Yes. When you add a link between station and ap you have to add the parameter link=’wired’ (e.g. net.addLink(sta1, ap2, link=’wired’) • May I customize the Access Point and Station configuration file? Answer: Since the Access Point is based on Hostapd you may customize the configuration file generated by Mininet-WiFi adding the parameter config when you create the access point, for example: ap1 = net.addAccessPoint( 'ap1', ,→ config='ctrl_interface=/var/run/hostapd/,ctrl_interface_group=0' ,→ ) The code above will create the file ap1-wlan1.apconf. The same can be done for stations when wpa_supplicant is used, for example: sta1 = net.addStation( 'sta1', config='eap=PEAP,identity="bob"' ) • Is it possible to plot hosts in graph? Yes, it is possible. You have to call the method below before calling net.addLink(): h1.plot(position='10,10,0') • The mode N supports booth 2.4 and 5Ghz. How can I make a choice between 2.4 or 5Ghz? Answer: You have to set band=2.4 or band=5 when you add an AP. 7 https://www.youtube.com/playlist?list=PLccoFREVAt_4nEtrkl59mjjf5ZzRX8DZA 8 https://groups.google.com/forum/#!forum/mininet-wifi-discuss 2. Mobility Models 2.1 Mobility Models Supported Mininet-WiFi supports the following mobility models: RandomWalk, TruncatedLevyWalk, RandomDirection, RandomWayPoint, GaussMarkov, ReferencePoint and TimeVariantCommunity. 2.2 How to setup Mobility? To use those mobility models you have to call the method net.startMobility() like in examples/mobilityModel.py. You may also have to consider the use of examples/mobility.py if you want a different type of mobility. Another alternative is to consider some parameters for specifics mobility models (not mandatory), for example: RandomWalk sta1 = net.addStation( ..., min_x=10, max_x=20, min_y=10, max_y=20, ,→ constantDistance=1, constantVelocity=1 ) min_x = Minimum X position max_x = Maximum X position min_y = Minimum Y position max_y = Maximum Y position constantDistance = the value for the constant distance traveled in each step. ,→ Default is 1.0. constantVelocity = the value for the constant node velocity. Default is 1.0 In the current implementation each step is 1 second. It is not possible to have a velocity larger than the distance. Chapter 2. Mobility Models 22 RandomDirection sta1 = net.addStation( ..., min_x=10, max_x=20, min_y=10, max_y=20, min_v=1, ,→ max_v=2 ) min_x max_x min_y max_y min_v max_v = = = = = = Minimum Maximum Minimum Maximum Minimum Maximum X position X position Y position Y position value for node velocity value for node velocity RandomWayPoint sta1 = net.addStation( ..., min_x=10, max_x=20, min_y=10, max_y=20, min_v=1, ,→ max_v=2 ) //min_v and max_v must have different values min_x max_x min_y max_y min_v max_v = = = = = = Minimum Maximum Minimum Maximum Minimum Maximum X position X position Y position Y position value for node velocity value for node velocity GaussMarkov sta1 = net.addStation( ..., min_x=10, max_x=20, min_y=10, max_y=20 ) min_x max_x min_y max_y = = = = Minimum Maximum Minimum Maximum X X Y Y position position position position 3. Propagation Models 3.1 Propagation Models Supported Mininet-WiFi supports the following propagation models: Friis Propagation Loss Model, Log-Distance Propagation Loss Model (DEFAULT ONE), Log-Normal Shadowing Propagation Loss Model, International Telecommunication Union (ITU) Propagation Loss Model and Two-Ray Ground Propagation Loss Model. 3.2 How to add specific Propagation Model? You have to call the method net.propagationModel() like in examples/propagationModel.py. You might have to consider some parameters for specifics propagation models (not mandatory), for example: Friis Propagation Loss Model net.propagationModel(model="friis", sL = $int) sL = system loss Log-Distance Propagation Loss Model net.propagationModel(model="logDistance", sL = $int, exp = $int) sL = system loss exp = exponent Log-Normal Shadowing Propagation Loss Model net.propagationModel(model="logNormalShadowing", sL = $int, exp = $int, ,→ variance = $int) sL = system loss exp = exponent variance = gaussian variance 24 Chapter 3. Propagation Models International Telecommunication Union (ITU) Propagation Loss Model net.propagationModel(model="ITU", lF = $int, nFloors = $int, pL = $int) lF = floor penetration loss factor nFloors = number of floors pL = power loss coefficient Two-Ray Ground Propagation Loss Model Attention: It does not give a good result for a short distance net.propagationModel(model="twoRayGround") 4. Replaying Traces Development still in progress 4.1 Replaying Mobility See the file examples/replaying/replayingMobility.py 4.2 Replaying Bandwidth See the file examples/replaying/replayingBandwidth.py 4.3 Replaying RSSI See the file examples/replaying/replayingRSSI.py 5. Tutorial 5.1 Introduction This tutorial has been developed by Brian Linkletter (http://www.brianlinkletter.com/mininet-wifisoftware-defined-network-emulator-supports-wifi-networks). We thank Brian for his time and this helpful tutorial. 5.2 First ideas In this post, I describe the unique functions available in the Mininet-WiFi network emulator and work through a few tutorials exploring its features. 5.2.1 How to read this post In this post, I present the basic functionality of Mininet-WiFi by working through a series of tutorials, each of which works through Mininet-WiFi features, while building on the knowledge presented in the previous tutorial. I suggest new users work through each tutorial in order. I do not attempt to cover every feature in Mininet-WiFi. Once you work through the tutorials in this post, you will be well equipped to discover all the features in Mininet-WiFi by working through the Mininet-WiFi example scripts- https://github.com/intrig-unicamp/mininetwifi/tree/master/examples, and reading the Mininet-WiFi wiki1 and mailing list2 . I assume the reader is already familiar with the [Mininet network emulator](http://mininet.org/) so I cover only the new WiFi features added by Mininet-WiFi. If you are not familiar with Mininet, please read my Mininet network simulator review3 before proceeding. I have also written many other posts about Mininet4 . 1 https://github.com/intrig-unicamp/mininet-wifi/wiki 2 https://groups.google.com/forum/#!forum/mininet-wifi-discuss 3 http://www.brianlinkletter.com/mininet-test-drive/ 4 http://www.brianlinkletter.com/tag/mininet/ 28 Chapter 5. Tutorial I start by discussing the functionality that Mininet-WiFi adds to Mininet: Mobility functions and WiFi interfaces. Then I show how to install Mininet-WiFi and work through the tutorials listed below: Tutorial #1: One access point shows how to run the simplest Mininet-WiFi scenario, shows how to capture wireless traffic in a Mininet-Wifi network, and discusses the issues with OpenFlow and wireless LANs. Tutorial #2: Multiple access points shows how to create a more complex network topology so we can experiment with a very basic mobility scenario. It discusses more about OpenFlow and shows how the Mininet reference controller works in Mininet-WiFi. Tutorial #3: Python API and scripts shows how to create more complex network topologies using the Mininet-WiFi Python API to define node positions in space and other node attributes. It also discusses how to interact with nodes running in a scenario with the Mininet-WiFi CLI, the Mininet-WiFi Python interpreter, and by running commands in a node’s shell. Tutorial #4: Mobility shows how to create a network mobility scenario in which stations move through space and may move in and out of range of access points. It also discusses the available functions that may be used to implement different mobility models using the Mininet-WiFi Python API. 5.2.2 Mininet-WiFi compared to Mininet Mininet-WiFi is an extension of the Mininet software defined network emulator. The Mininet-WiFi developer did not modify any existing Mininet functionality, but added new functionality. 5.2.3 Mininet-WiFi and Mobility Broadly defined, mobility in the context of data networking refers to the ability of a network to accommodate hosts moving from one part of the network to another. For example: a cell phone user may switch to a wifi access point when she walks into a coffee shop; or a laptop user may walk from her office in one part of a building to a meeting room in another part of the building and still being able to connect to the network via the nearest WiFi access point. While the standard Mininet network emulator may be used to test mobility (In the Mininet examples folder, we find a mobility.py script that demonstrates methods that may be used to create a scenario where a host connected to one switch moves its connection to another switch), MininetWiFi offers more options to emulate complex scenarios where many hosts will be changing the switches to which they are connected. Mininet-WiFi adds new classes that simplify the programming work required by researchers to create Mobility scenarios. Mininet-WiFi does not modify the reference SDN controller provided by standard Mininet so the reference controller cannot manage the mobility of users in the wireless network. Researchers must use a remote controller that supports the CAPWAP protocol (NOTE: I’ve not tried this and I do not know if it will work without modifications or additional programming), or manually add and delete flows in the access points and switches. 5.2 First ideas 5.2.4 29 802.11 Wireless LAN Emulation Mininet-wifi incorporates the Linux 802.11 SoftMAC5 wireless drivers, the cfg802116 wireless configuration interface and the mac80211_hwsim7 wireless simulation drivers in its access points. The mac80211_hwsim driver is a software simulator for Wi-Fi radios. It can be used to create virtual wi-fi interfaces8 that use the 802.11 SoftMAC wireless LAN driver9 . Using this tool, researchers may emulate a Wi-Fi link between virtual machines10 - some mac80211_hwsim practical examples and supporting information are at the following links: lab11 , thesis12 , hostapd13 , wpa-supplicant14 , docs-115 , and docs-216 . The 80211_hwsim driver enables researchers to emulate the wifi protocol control messages passing between virtual wireless access points and virtual mobile stations in a network emulation scenario. By default, 80211_hwsim simulates perfect conditions, which means there is no packet loss or corruption. 5.2.5 Mininet-WiFi display graph Since locations of nodes in space is an important aspect of WiFi networks, Mininet WiFi provides a graphical display (figure 5.1) showing locations of WiFi nodes in a graph. The graph may be created by calling its method in the Mininet-WiFi Python API (see examples in the tutorials below). The graph will show wireless access points and stations, their positions in space and will display the affects of the range parameter for each node. The graph will not show any "wired" network elements such as standard Mininet hosts or switches, Ethernet connections between access points, hosts, or switches. 5.2.6 Install Mininet-WiFi on a Virtual Machine First, we need to create a virtual machine that will run the Mininet-WiFi network emulator. In the example below, we will use the VirtualBox virtual machine manager because it is open-source and runs on Windows, Mac OS, and Linux. 5.2.7 Set up a new Ubuntu Server VM Install Ubuntu Server in a new VM. Download an Ubuntu Server ISO image from the Ubuntu web site. See my post about installing Debian Linux in a VM17 . Follow the same steps to install Ubuntu. In this example, we will name the VM Mininet-WiFi. 5 https://wireless.wiki.kernel.org/en/developers/documentation/glossary#softmac 6 http://www.linuxwireless.org/en/developers/Documentation/cfg80211 7 https://wireless.wiki.kernel.org/en/users/drivers/mac80211_hwsim 8 http://stackoverflow.com/questions/33091895/virtual-wifi-802-11-interface-similar-to-veth-on-linux 9 http://linuxwireless.org/en/developers/Documentation/mac80211/__v49.html 10 https://w1.fi/cgit/hostap/plain/tests/hwsim/example-setup.txt 11 http://www2.cs.siu.edu/s̃harvey/code/cs441/cs441_lab.pdf 12 http://upcommons.upc.edu/bitstream/handle/2099.1/19202/memoria.pdf?sequence=4 13 https://nims11.wordpress.com/2012/04/27/hostapd-the-linux-way-to-create-virtual-wifi-access-point/ 14 https://wiki.debian.org/WiFi/HowToUse#wpa_supplicant 15 https://www.kernel.org/doc/readme/Documentation-networking-mac80211_hwsim-README 16 https://github.com/penberg/linux-kvm/tree/master/Documentation/networking/mac80211_hwsim)) 17 http://www.brianlinkletter.com/installing-debian-linux-in-a-virtualbox-virtual-machine/ Chapter 5. Tutorial 30 Figure 5.1: Mininet-WiFi Graph 5.2.8 Set up the Mininet-WiFi VM To ensure that the VM can display X applications such as Wireshark on your host computer’s desktop, read through my post about setting up the standard Mininet VM18 and set up the host-only network adapter, the X windows server, and your SSH software. Now you can connect to the VM via SSH with X Forwarding enabled. In the example below, my host computer is t420 and the Mininet WiFi VM is named wifi. t420:~$ ssh -X 192.168.52.101 wifi:~$ 5.3 Mininet-WiFi Tutorial #1: One access point The simplest network is the default topology, which consists of a wireless access point with two wireless stations. The access point is a switch connected to a controller. The stations are hosts. This simple lab will allow us to demonstrate how to capture wireless control traffic and will demonstrate the way an OpenFlow-enabled access point handles WiFi traffic on the wlan interface. 5.3.1 Capturing Wireless control traffic in Mininet-WiFi To view wireless control traffic we must first start Wireshark: wifi:~$ wireshark & 18 http://www.brianlinkletter.com/set-up-mininet/ 5.3 Mininet-WiFi Tutorial #1: One access point 31 Figure 5.2: Start capture on hwsim0 interface Then, start Mininet-WiFi with the default network scenario using the command below: wifi:~$ sudo mn --wifi Next, enable the hwsim0 interface. The hwsim0 interface is the software interface created by MininetWiFi that copies all wireless traffic to all the virtual wireless interfaces in the network scenario. It is the easiest way to monitor the wireless packets in Mininet-WiFi. mininet-wifi> sh ifconfig hwsim0 up Now, in Wireshark (figure 5.2, refresh the interfaces and then start capturing packets on the *hwsim0* interface. You should see wireless control traffic. Next, run a ping command: mininet-wifi> sta1 ping sta2 In Wireshark (figure 5.3), see the wireless frames and the ICMP packets encapsulated in Wireless frames passing through the hwsim0 interface. Stop the ping command by pressing Ctrl-C. In this default setup, any flows created in the access point (that’s if they’re created – see below for more on this issue) will expire in 60 seconds. 5.3.2 Wireless Access Points and OpenFlow In this simple scenario, the access point has only one interface, ap1-wlan0. By default, stations associated with an access point connect in infrastructure mode so wireless traffic between stations must pass through the access point. If the access point works similarly to a switch in standard Mininet, we expect to see OpenFlow messages exchanged between the access point and the controller whenever the access point sees traffic for which it does not already have flows established. To view OpenFlow packets, stop the Wireshark capture and switch to the loopback interface. Start capturing again on the loopback interface. Use the OpenFlow_1.0 filter to view only OpenFlow messages. Then, start some traffic running with the ping command and look at the OpenFlow messages captured in Wireshark. Chapter 5. Tutorial 32 Figure 5.3: Wireshark capturing WiFi control traffic mininet-wifi> sta1 ping sta2 I was expecting that the first ICMP packet generated by the ping command should be flooded to the controller, and the controller would set up a flows on the access point so the two stations could exchange packets. Instead, I found that the two stations were able to exchange packets immediately and the access point did not flood the ICMP packets to the controller. Only an ARP packet, which is in a broadcast frame, gets flooded to the controller and is ignored (figure 5.4. Check to see if flows have been created in the access point: mininet-wifi> dpctl dump-flows *** ap1 -----------------------------------------NXST_FLOW reply (xid=0x4): We see that no flows have been created on the access point. How do the two access points communicate with each other? I do not know the answer but I have an idea. My research indicates that OpenFlow-enabled switches (using OpenFlow 1.0 or 1.3) will reject "hairpin connections", which are flows that cause traffic to be sent out the same port in which it was received. A wireless access point, by design, receives and sends packets on the same wireless interface. Stations connected to the same wireless access point would require a "hairpin connection" on the access point to communicate with each other. I surmise that, to handle this issue, Linux treats the WLAN interface in each access point like the radio network sta1-ap1-sta2 as if it is a "hub", where ap1-wlan0 provides the "hub" functionality for data passing between sta1 and sta2. ap1-wlan0 switches packets in the wireless domain and will not bring a packet into the "Ethernet switch" part of access point ap1 unless it must be switched to another interface on ap1 other than back out ap1-wlan0. 5.3.3 Stop the tutorial Stop the Mininet ping command by pressing Ctrl-C. 5.4 Mininet-WiFi Tutorial #2: Multiple access points 33 Figure 5.4: No OpenFlow messages passing to the controller In the Wireshark window, stop capturing and quit Wireshark. Stop Mininet-Wifi and clean up the system with the following commands: mininet-wifi> exit wifi:~$ sudo mn -c 5.4 Mininet-WiFi Tutorial #2: Multiple access points When we create a network scenario with two or more wireless access points, we can show more of the functions available in Mininet-WiFi. In this tutorial, we will create a linear topology with three access points, where one station is connected to each access point. Remember, you need to already know basic Mininet commands19 to appreciate how we create topologies using the Mininet command line. Run Mininet-Wifi and create a linear topology with three access points: sudo mn --wifi --topo linear,3 From the output of the command, we can see how the network is set up and which stations are associated with which access points. *** Creating network *** Adding controller *** Adding hosts and stations: sta1 sta2 sta3 *** Adding switches and access point(s): ap1 ap2 ap3 *** Adding links and associating station(s): (ap2, ap1) (ap3, ap2) (sta1, ap1) (sta2, ap2) (sta3, ap3) 19 http://mininet.org/walkthrough/ Chapter 5. Tutorial 34 *** Starting controller(s) c0 *** Starting switches and access points ap1 ap2 ap3 ... *** Starting CLI: mininet-wifi> We can also verify the configuration using the Mininet CLI commands net and dump. For example, we can run the net command to see the connections between nodes: mininet-wifi> net sta1 sta1-wlan0:None sta2 sta2-wlan0:None sta3 sta3-wlan0:None ap1 lo: ap1-eth1:ap2-eth1 ap2 lo: ap2-eth1:ap1-eth1 ap2-eth2:ap3-eth1 ap3 lo: ap3-eth1:ap2-eth2 c0 From the net command above, we see that ap1, ap2, and ap3 are connected together in a linear fashion by Ethernet links. But, we do not see any information about to which access point each station is connect. This is because they are connected over a "radio" interface so we need to run the iw command at each station to observe to which access point each is associated. To check which access points are "visible" to each station, use the iw scan command: mininet-wifi> sta1 iw dev sta1-wlan0 scan | grep ssid SSID: ssid_ap1 SSID: ssid_ap2 SSID: ssid_ap3 Verify the access point to which each station is currently connected with the iw link command. For example, to see the access point to which station sta1 is connected, use the following command: mininet-wifi> sta1 iw dev sta1-wlan0 link Connected to 02:00:00:00:03:00 (on sta1-wlan0) SSID: ssid_ap1 freq: 2412 RX: 1853238 bytes (33672 packets) TX: 7871 bytes (174 packets) signal: -30 dBm tx bitrate: 54.0 MBit/s bss flags: dtim period: beacon int: mininet-wifi> short-slot-time 2 100 5.4 Mininet-WiFi Tutorial #2: Multiple access points 5.4.1 35 A simple mobility scenario In this example, each station is connected to a different wireless access point. We can use the iw command to change which access point to which each station is connected. Note: The iw commands may be used in static scenarios like this but should not be used when Mininet-WiFi automatically assigns associations in more realistic mobility scenarios. We’ll discuss how Mininet-WiFi handles real mobility and how to use iw commands with Mininet-WiFi later in this post. Let’s decide we want sta1, which is currently associated with ap1, to change its association to ap2. Manually switch the sta1 association from ap1 (which is ssid_ap1) to ap2 (which is ssid_ap2) using the following commands: mininet-wifi> sta1 iw dev sta1-wlan0 disconnect mininet-wifi> sta1 iw dev sta1-wlan0 connect ssid_ap2 Verify the change with the iw link command: mininet-wifi> sta1 iw dev sta1-wlan0 link Connected to 02:00:00:00:04:00 (on sta1-wlan0) SSID: ssid_ap2 freq: 2412 RX: 112 bytes (4 packets) TX: 103 bytes (2 packets) signal: -30 dBm tx bitrate: 1.0 MBit/s bss flags: dtim period: beacon int: mininet-wifi> short-slot-time 2 100 We see that sta1 is now associated with ap2. So we’ve demonstrated a basic way to make stations mobile, where they switch their association from one access point to another. 5.4.2 OpenFlow flows in a mobility scenario Now let’s see how the Mininet reference controller handles this simple mobility scenario. We need to get some traffic running from sta1 to sta3 in a way that allows us to access the Mininet-WiFi command line. We’ll run the ping command in an xterm window on sta3. First, check the IP addresses on sta1 and sta3 so we know which parameters to use in our test. The easiest way to see all IP addresses is to run the dump command: mininet-wifi> dump Chapter 5. Tutorial 36 Figure 5.5: xterm window on sta3 mininet-wifi> So we see that sta1 has IP address 10.0.0.1 and sta3 has IP address 10.0.0.3. Next, start an xterm window on sta3: mininet-wifi> xterm sta3 This opens an xterm window (figure 5.5 from sta3. In that window, run the following command to send ICMP messages from sta3 to sta1: root@mininet-wifi:~# ping 10.0.0.1 Since these packets will be forwarded by the associated access points out a port other then the port on which the packets were received, the access points will operate like normal OpenFlow-enabled switches. Each access point will forward the first ping packet it receives in each direction to the Mininet reference controller. The controller will set up flows on the access points to establish a connection between the stations sta1 and sta3. If we run Wireshark (figure 5.6 and enable packet capture on the Loopback interface, then filter using with of (for Ubuntu 14.04) or openflow_v1 (for Ubuntu 15.10 and later), we will see OpenFlow messages passing to and from the controller. Now, in the Mininet CLI, check the flows on each switch with the dpctl dump-flows command. mininet-wifi> dpctl dump-flows *** ap1 ----------------------------------------------NXST_FLOW reply (xid=0x4): *** ap2 ----------------------------------------------- 5.4 Mininet-WiFi Tutorial #2: Multiple access points 37 Figure 5.6: Wireshark capturing OpenFlow messages NXST_FLOW reply (xid=0x4): idle_timeout=60, idle_age=0, ,→ priority=65535,arp,in_port=2,vlan_tci=0x0000,dl_src=02:00:00:00:02:00, ,→ dl_dst=02:00:00:00:00:00,arp_spa=10.0.0.3,arp_tpa=10.0.0.1,arp_op=2 ,→ actions=output:3 cookie=0x0, duration=1068.17s, table=0, n_packets=35, n_bytes=1470, ,→ idle_timeout=60, idle_age=0, ,→ priority=65535,arp,in_port=3,vlan_tci=0x0000,dl_src=02:00:00:00:00:00, ,→ dl_dst=02:00:00:00:02:00,arp_spa=10.0.0.1,arp_tpa=10.0.0.3,arp_op=1 ,→ actions=output:2 cookie=0x0, duration=1073.174s, table=0, n_packets=1073, ,→ n_bytes=105154, idle_timeout=60, idle_age=0, ,→ priority=65535,icmp,in_port=3,vlan_tci=0x0000,dl_src=02:00:00:00:00:00, dl_dst=02:00:00:00:02:00,nw_src=10.0.0.1,nw_dst=10.0.0.3,nw_tos=0, ,→ ,→ icmp_type=0,icmp_code=0 actions=output:2 cookie=0x0, duration=1073.175s, table=0, n_packets=1073, n_bytes=105154, idle_timeout=60, idle_age=0, ,→ ,→ priority=65535,icmp,in_port=2,vlan_tci=0x0000,dl_src=02:00:00:00:02:00, ,→ dl_dst=02:00:00:00:00:00,nw_src=10.0.0.3,nw_dst=10.0.0.1,nw_tos=0, icmp_type=8,icmp_code=0 actions=output:3 ,→ *** ap3 ----------------------------------------------NXST_FLOW reply (xid=0x4): Chapter 5. Tutorial 38 cookie=0x0, duration=1068.176s, table=0, n_packets=35, n_bytes=1470, ,→ idle_timeout=60, idle_age=0, ,→ priority=65535,arp,in_port=2,vlan_tci=0x0000,dl_src=02:00:00:00:02:00, ,→ dl_dst=02:00:00:00:00:00,arp_spa=10.0.0.3,arp_tpa=10.0.0.1,arp_op=2 ,→ actions=output:1 idle_timeout=60, idle_age=0, ,→ priority=65535,arp,in_port=1,vlan_tci=0x0000,dl_src=02:00:00:00:00:00, ,→ dl_dst=02:00:00:00:02:00,arp_spa=10.0.0.1,arp_tpa=10.0.0.3,arp_op=1 ,→ actions=output:2 cookie=0x0, duration=1073.182s, table=0, n_packets=1073, ,→ n_bytes=105154, idle_timeout=60, idle_age=0, ,→ priority=65535,icmp,in_port=1,vlan_tci=0x0000,dl_src=02:00:00:00:00:00, ,→ dl_dst=02:00:00:00:02:00,nw_src=10.0.0.1,nw_dst=10.0.0.3,nw_tos=0, ,→ icmp_type=0,icmp_code=0 actions=output:2 cookie=0x0, duration=1073.185s, table=0, n_packets=1073, ,→ n_bytes=105154, idle_timeout=60, idle_age=0, ,→ priority=65535,icmp,in_port=2,vlan_tci=0x0000,dl_src=02:00:00:00:02:00, ,→ dl_dst=02:00:00:00:00:00,nw_src=10.0.0.3,nw_dst=10.0.0.1,nw_tos=0, ,→ icmp_type=8,icmp_code=0 actions=output:1 mininet-wifi> We see flows set up on ap2 and ap3, but not on ap1. This is because sta1 is connected to ap2 and sta3 is connected to ap3 so all traffic is passing through only ap2 and ap3. What will happen if sta1 moves back to ap1? Move sta1 back to access point ap1 with the following commands: mininet-wifi> sta1 iw dev sta1-wlan0 disconnect mininet-wifi> sta1 iw dev sta1-wlan0 connect ssid_ap1 The ping command running on sta3 stops working. We see no more pings completed. In this case, access points ap2 and ap3 already have flows for ICMP messages coming from sta3 so they just keep sending packets towards the ap2-wlan0 interface to reach where they think sta1 is connected. Since ping messages never get to sta1 in its new location, the access point ap1 never sees any ICMP traffic so does not request any flow updates from the controller. Check the flow tables in the access points again: mininet-wifi> dpctl dump-flows *** ap1 ----------------------------------------------NXST_FLOW reply (xid=0x4): cookie=0x0, duration=40.959s, table=0, n_packets=1, n_bytes=42, ,→ idle_timeout=60, idle_age=40, ,→ priority=65535,arp,in_port=1,vlan_tci=0x0000,dl_src=02:00:00:00:02:00, dl_dst=02:00:00:00:00:00,arp_spa=10.0.0.3,arp_tpa=10.0.0.1,arp_op=1 ,→ ,→ actions=output:2 cookie=0x0, duration=40.958s, table=0, n_packets=1, n_bytes=42, ,→ idle_timeout=60, idle_age=40, ,→ priority=65535,arp,in_port=2,vlan_tci=0x0000,dl_src=02:00:00:00:00:00, ,→ dl_dst=02:00:00:00:02:00,arp_spa=10.0.0.1,arp_tpa=10.0.0.3,arp_op=2 actions=output:1 ,→ 5.4 Mininet-WiFi Tutorial #2: Multiple access points 39 *** ap2 ----------------------------------------------NXST_FLOW reply (xid=0x4): cookie=0x0, duration=40.968s, table=0, n_packets=1, n_bytes=42, ,→ idle_timeout=60, idle_age=40, ,→ priority=65535,arp,in_port=2,vlan_tci=0x0000,dl_src=02:00:00:00:02:00, ,→ dl_dst=02:00:00:00:00:00,arp_spa=10.0.0.3,arp_tpa=10.0.0.1,arp_op=1 ,→ actions=output:1 cookie=0x0, duration=40.964s, table=0, n_packets=1, n_bytes=42, ,→ idle_timeout=60, idle_age=40, ,→ priority=65535,arp,in_port=1,vlan_tci=0x0000,dl_src=02:00:00:00:00:00, ,→ dl_dst=02:00:00:00:02:00,arp_spa=10.0.0.1,arp_tpa=10.0.0.3,arp_op=2 ,→ actions=output:2 cookie=0x0, duration=1214.279s, table=0, n_packets=1214, ,→ n_bytes=118972, idle_timeout=60, idle_age=0, ,→ priority=65535,icmp,in_port=2,vlan_tci=0x0000,dl_src=02:00:00:00:02:00, ,→ dl_dst=02:00:00:00:00:00,nw_src=10.0.0.3,nw_dst=10.0.0.1,nw_tos=0, ,→ icmp_type=8,icmp_code=0 actions=output:3 *** ap3 ----------------------------------------------NXST_FLOW reply (xid=0x4): cookie=0x0, duration=40.978s, table=0, n_packets=1, n_bytes=42, ,→ idle_timeout=60, idle_age=40, ,→ priority=65535,arp,in_port=2,vlan_tci=0x0000,dl_src=02:00:00:00:02:00, ,→ dl_dst=02:00:00:00:00:00,arp_spa=10.0.0.3,arp_tpa=10.0.0.1,arp_op=1 ,→ actions=output:1 cookie=0x0, duration=40.971s, table=0, n_packets=1, n_bytes=42, ,→ idle_timeout=60, idle_age=40, ,→ priority=65535,arp,in_port=1,vlan_tci=0x0000,dl_src=02:00:00:00:00:00, ,→ dl_dst=02:00:00:00:02:00,arp_spa=10.0.0.1,arp_tpa=10.0.0.3,arp_op=2 ,→ actions=output:2 cookie=0x0, duration=1214.288s, table=0, n_packets=1214, ,→ n_bytes=118972, idle_timeout=60, idle_age=0, ,→ priority=65535,icmp,in_port=2,vlan_tci=0x0000,dl_src=02:00:00:00:02:00, ,→ dl_dst=02:00:00:00:00:00,nw_src=10.0.0.3,nw_dst=10.0.0.1,nw_tos=0, ,→ icmp_type=8,icmp_code=0 actions=output:1 mininet-wifi> The controller sees some LLC messages from sta1 but does recognize that sta1 has moved to a new access point, so it does nothing. Since the controller does not modify any flows in the access points, none of the ICMP packets still being generated by sta3 will reach sta1 so it cannot reply. This situation will remain as long as the access points ap2 and ap3 continue to see ICMP packets from sta3, which keeps the old flow information alive in their flow tables. One "brute force" way to resolve this situation is to delete the flows on the switches. In this simple example, it’s easier to just delete all flows. Delete the flows in the access points using the command below: mininet-wifi> dpctl del-flows 40 Chapter 5. Tutorial Now the ping command running in the xterm window on sta3 should show that pings are being completed again. Once all flows were deleted, ICMP messages received by the access points do not match any existing flows so the access points communicate with the controller to set up new flows. If we dump the flows we see that the ICMP packets passing between sta3 and sta1 are now traversing across all three acces points. mininet-wifi> dpctl dump-flows *** ap1 ----------------------------------------------NXST_FLOW reply (xid=0x4): cookie=0x0, duration=10.41s, table=0, n_packets=11, n_bytes=1078, ,→ idle_timeout=60, idle_age=0, ,→ priority=65535,icmp,in_port=2,vlan_tci=0x0000,dl_src=02:00:00:00:00:00, ,→ dl_dst=02:00:00:00:02:00,nw_src=10.0.0.1,nw_dst=10.0.0.3,nw_tos=0, ,→ icmp_type=0,icmp_code=0 actions=output:1 cookie=0x0, duration=9.41s, table=0, n_packets=10, n_bytes=980, idle_timeout=60, idle_age=0, ,→ priority=65535,icmp,in_port=1,vlan_tci=0x0000,dl_src=02:00:00:00:02:00, ,→ ,→ dl_dst=02:00:00:00:00:00,nw_src=10.0.0.3,nw_dst=10.0.0.1,nw_tos=0, icmp_type=8,icmp_code=0 actions=output:2 ,→ *** ap2 ----------------------------------------------NXST_FLOW reply (xid=0x4): cookie=0x0, duration=10.414s, table=0, n_packets=11, n_bytes=1078, ,→ idle_timeout=60, idle_age=0, ,→ priority=65535,icmp,in_port=1,vlan_tci=0x0000,dl_src=02:00:00:00:00:00, ,→ dl_dst=02:00:00:00:02:00,nw_src=10.0.0.1,nw_dst=10.0.0.3,nw_tos=0, ,→ icmp_type=0,icmp_code=0 actions=output:2 cookie=0x0, duration=9.417s, table=0, n_packets=10, n_bytes=980, ,→ idle_timeout=60, idle_age=0, ,→ priority=65535,icmp,in_port=2,vlan_tci=0x0000,dl_src=02:00:00:00:02:00, ,→ dl_dst=02:00:00:00:00:00,nw_src=10.0.0.3,nw_dst=10.0.0.1,nw_tos=0, ,→ icmp_type=8,icmp_code=0 actions=output:1 *** ap3 ----------------------------------------------NXST_FLOW reply (xid=0x4): cookie=0x0, duration=10.421s, table=0, n_packets=11, n_bytes=1078, ,→ idle_timeout=60, idle_age=0, ,→ priority=65535,icmp,in_port=1,vlan_tci=0x0000,dl_src=02:00:00:00:00:00, ,→ dl_dst=02:00:00:00:02:00,nw_src=10.0.0.1,nw_dst=10.0.0.3,nw_tos=0, ,→ icmp_type=0,icmp_code=0 actions=output:2 cookie=0x0, duration=9.427s, table=0, n_packets=10, n_bytes=980, ,→ idle_timeout=60, idl_age=0, ,→ priority=65535,icmp,in_port=2,vlan_tci=0x0000,dl_src=02:00:00:00:02:00, ,→ dl_dst=02:00:00:00:00:00,nw_src=10.0.0.3,nw_dst=10.0.0.1,nw_tos=0, ,→ icmp_type=8,icmp_code=0 actions=output:1 mininet-wifi> We have shown how the Mininet reference controller works in Mininet-WiFi. The Mininet 5.5 Mininet-WiFi Tutorial #3: Python API and scripts 41 reference controller does not have the ability to detect when a station moves from one access point to another. When this happens, we must delete the existing flows so that new flows can be created. We will need to us a more advanced remote controller, such as OpenDaylight, to enable station mobility but that is a topic outside the scope of this post. 5.4.3 Stop the tutorial Stop the Mininet ping command by pressing Ctrl-C. In the Wireshark window, stop capturing and quit Wireshark. Stop Mininet-Wifi and clean up the system with the following commands: mininet-wifi> exit wifi:~$ sudo mn -c 5.5 Mininet-WiFi Tutorial #3: Python API and scripts Mininet provides a Python API so users can create simple Python scripts that will set up custom topologies. Mininet-WiFi extends this API to support a wireless environment. When you use the normal Mininet mn command with the –wifi option to create Mininet-WiFi topologies, you do not have access to most of the extended functionality provided in Mininet-WiFi. To access features that allow you to emulate the behavior of nodes in a wireless LAN, you need to use the Mininet-Wifi extensions to the Mininet Python API. 5.5.1 The Mininet-WiFi Python API The Mininet-WiFi developers added new classes to Mininet to support emulation of nodes in a wireless environment. Mininet-WiFi adds addStation and addAccessPoint methods, and a modified addLink method to define the wireless environment. If you are just beginning to write scripts for Mininet-WiFi, you can use the example scripts as a starting point. The Mininet-WiFi developers created example scripts that show how to use most of the features in Mininet-WiFi. In all of the tutorials I show below, I started with an example script and modified it. Mininet-Wifi example scripts are in the /mininet-wifi/examples directory. 5.5.2 Basic station and access point methods In a simple scenario, you may add a station and an access point with the following methods in a Mininet-WiFi Python script: Add a new station named sta1, with all parameters set to default values: net.addStation( 'sta1' ) Add a new access point named ap1, with SSID ap1-ssid, and all other parameters set to default values: net.addAccessPoint( 'ap1', ssid='new_ssid' ) Add a wireless association between station and access point, with default values for link attributes: net.addLink( ap1, sta1 ) Chapter 5. Tutorial 42 For more complex scenarios, more parameters are available for each method. You may specify the MAC address, IP address, location in three dimensional space, radio range, and more. For example, the following code defines an access point and a station, and creates an association (a wireless connection) between the two nodes and applies some traffic control parameters to the connection to make it more like a realistic radio environment, adding badwidth restrictions, an error rate, and a propagation delay: Add a station and specify the wireless encryption method, the station MAC address, IP address, and position in virtual space: net.addStation( 'sta1', passwd='123456789a', encrypt='wpa2', ,→ mac='00:00:00:00:00:02', ip='10.0.0.2/8', position='50,30,0' ) Add an access point and specify the wireless encryption method, SSID, wireless mode, channel, position, and radio range: net.addAccessPoint( 'ap1', passwd='123456789a', encrypt='wpa2', ssid= ,→ 'ap1-ssid', mode= 'g', channel= '1', position='30,30,0', range=30 ) To activate association control in a static network, you may use the *associationControl* method, which makes Mininet-WiFi automatically choose which access point a station will connect to based on the range between stations and access points. For example, use the following method to use the *strongest signal first* when determining connections between station and access points: net.associationControl( 'ssf' ) 5.5.3 Classic Mininet API The Mininet WiFi Python API still supports the standard Mininet node types – switches, hosts, and controllers. For example: Add a host. Note that the station discussed above is a type of host nodem with a wireless interface instead of an Ehternet interface. net.addHost( 'h1' ) Add a switch. Note that the access point discussed above is a type of switch that has one wireless interface (*wlan0*) and any number of Ethernet interfaces (up to the maximum supported by your installed version of Open vSwitch). net.addSwitch( 's1' ) Add an Ethernet link between two nodes. Note that if you use *addLink* to connect two access points together (and are using the default Infrastructure mode), Mininet-WiFi creates an Ethernet link between them. net.addLink( s1, h1 ) Add a controller: net.addController( 'c0' ) Using the Python API, you may build a topology that includes hosts, switches, stations, access points, and multiple controllers. 5.5 Mininet-WiFi Tutorial #3: Python API and scripts 5.5.4 43 Example In the example below, I created a Python program that will set up two stations connected to two access points, and set node positions and radio range so that we can see how these properties affect the emulated network. 1 # ! / usr / bin / python 2 3 4 5 6 7 from from from from from mininet mininet mininet mininet mininet . net import Mininet . node i m p o r t C o n t r o l l e r , OVSKernelAP . l i n k i m p o r t TCLink . c l i i m p o r t CLI . log import setLogLevel 8 9 def topology ( ) : 10 11 n e t = M i n i n e t ( c o n t r o l l e r = C o n t r o l l e r , l i n k =TCLink , a c c e s s P o i n t =OVSKernelAP ) 12 13 14 15 16 17 18 p r i n t " *** C r e a t i n g n o d e s " ap1 = n e t . a d d A c c e s s P o i n t ( ' ap1 ' , s s i d = ' s s i d −ap1 ' , mode= ' g ' p o s i t i o n = ' 1 0 , 3 0 , 0 ' , r a n g e = ' 20 ' ) ap2 = n e t . a d d A c c e s s P o i n t ( ' ap2 ' , s s i d = ' s s i d −ap2 ' , mode= ' g ' p o s i t i o n = ' 5 0 , 3 0 , 0 ' , r a n g e = ' 20 ' ) s t a 1 = n e t . a d d S t a t i o n ( ' s t a 1 ' , mac= ' 0 0 : 0 0 : 0 0 : 0 0 : 0 0 : 0 1 ' , i p = ' p o s i t i o n = ' 10 ,20 ,0 ' ) s t a 2 = n e t . a d d S t a t i o n ( ' s t a 2 ' , mac= ' 0 0 : 0 0 : 0 0 : 0 0 : 0 0 : 0 2 ' , i p = ' p o s i t i o n = ' 50 ,20 ,0 ' ) c1 = n e t . a d d C o n t r o l l e r ( ' c1 ' , c o n t r o l l e r = C o n t r o l l e r ) 19 20 21 p r i n t " *** C o n f i g u r i n g w i f i n o d e s " net . configureWifiNodes ( ) 22 23 24 """ p l o t graph """ n e t . p l o t G r a p h ( max_x =60 , max_y = 60 ) 25 26 27 28 # Comment o u t t h e f o l l o w i n g two l i n e s t o d i s a b l e AP p r i n t " *** E n a b l i n g a s s o c i a t i o n c o n t r o l ( AP ) " net . associationControl ( ' ssf ' ) 29 30 31 32 33 p r i n t " *** C r e a t i n g l i n k s and a s s o c i a t i o n s " n e t . a d d L i n k ( ap1 , ap2 ) n e t . a d d L i n k ( ap1 , s t a 1 ) n e t . a d d L i n k ( ap2 , s t a 2 ) 34 35 36 37 38 39 p r i n t " *** S t a r t i n g n e t w o r k " net . build () c1 . s t a r t ( ) ap1 . s t a r t ( [ c1 ] ) ap2 . s t a r t ( [ c1 ] ) 40 41 42 p r i n t " *** Running CLI " CLI ( n e t ) 43 44 45 p r i n t " *** S t o p p i n g n e t w o r k " net . stop () 46 47 i f __name__ == ' __main__ ' : , channel= ' 1 ' , , channel= ' 6 ' , 10.0.0.1/8 ' , 10.0.0.2/8 ' , Chapter 5. Tutorial 44 Figure 5.7: The position-test.py script running setLogLevel ( topology () 48 49 ' info ' ) codes/position–test.py I saved the file with the name position-test.py and made it executable. 5.5.5 Working at runtime Mininet-WiFi python scripts may be run from the command line by running the script directly, or by calling it as part of a Python command. The only difference is how the path is stated. For example: wifi:~/scripts $ sudo ./position-test.py or, wifi:~$ sudo python position-test.py The position-test.py script will set open the Mininet-WiFi graph window and show the locations of each wireless node in space (figure 5.7, and the range attribute of each node. While the scenario is running, we can query information about the network from either the Mininet-WiFi command line or from the Python interpreter and we can log into running nodes to gather information or make configuration changes. 5.5.6 Mininet-WiFi CLI The Python script position-test.py places nodes in specific positions. When the scenario is running, we can use the Mininet-WiFi command line interface (CLI) commands to can check the geometric relationship between nodes in space, and information about each node. 5.5 Mininet-WiFi Tutorial #3: Python API and scripts 5.5.7 45 Position The position CLI command outputs the location of a node in virtual space as measured by three values, one for each of the vertices X, Y, and Z. Suppose we want to know the position of the access point ap1 in the network scenario’s virtual space. We may use the position CLI command to view a node’s position: mininet-wifi> py ap1.params['position'] We may also check the position of the station sta2: mininet-wifi> py sta.params['position'] 5.5.8 Distance The distance CLI command tells us the distance between two nodes. For example, we may check how far apart access point ap1 and station sta2 are from each other using the distance CLI command: mininet-wifi> distance ap1 sta2 The distance between ap1 and sta2 is 41.23 meters 5.5.9 Mininet-WiFi Python runtime interpreter In addition to the CLI, Mininet-WiFi supports running Python code directly at the command line using the py command. Simple, Python functions may be called to get additional information about the network, or to make simple changes while the scenario is running. 5.5.10 Getting network information The examples I show below are useful for gathering information about stations and access points. To see the range of an access point or station, call the range function. Call it using the name of the node followed by the function as shown below for access point ap1: mininet-wifi> py ap1.params['range'] 20 To see which station is associated with an access point (in this example ap1) call the associatedStations function: mininet-wifi> py ap1.params['associatedStations'] [ ] To see which access point is associated with a station (in this example sta1) call the associatedTo key: mininet-wifi>py sta1.params['associatedTo'] [ ] Chapter 5. Tutorial 46 You may also query the received signal strength indicator (rssi), transmitted power (txpower), service set indicator (ssid), channel, and frequency of each wireless node using the Python interpreter. As we can see, the output of Python functions is formatted as strings and numbers that may sometimes be hard to read. This is because these functions are built to support the program, not to be read by humans. However, if you which functions are available to be called at the Mininet-WiFi command line you will be able to get information you cannot get through the standard Mininet-WiFi CLI. 5.5.11 Changing the network during runtime Mininet-WiFi provides Python functions that can be used during runtime to make changes to node positions and associations. These functions are useful when we have a static setup and want to make arbitrary changes on demand. This makes it possible to do testing or demonstrations with carefully controlled scenarios. To change the access point to which a station is associated (provided the access point is within range): mininet-wifi> py sta1.moveAssociationTo('sta1-wlan0', ap1) To move a station or access point in space to another coordinate position: mininet-wifi> py sta1.setPosition('40,20,40') To change the range of a station or access point: mininet-wifi> py sta1.setRange(100) The commands above will all impact which access points and which stations associate with each other. The behavior of the network will be different depending on whether association control is enabled or disabled in the position-test.py script. 5.5.12 Running commands in nodes When running a scenario, users may make configuration changes on nodes to implement some additional functionality. This can be done from the Mininet-WiFi command line by sending commands to the node’s command shell. Start the command with the name of the node followed by a space, then enter the command to run on that node. For example, to see information about the WLAN interface on a station named sta1, run the command: mininet-wifi> sta1 iw dev sta1-wlan0 link Another way to run commands on nodes is to open an xterm window on that node and enter commands in the xterm window. For example, to open an xterm window on station *sta1*, run the command: mininet-wifi> xterm sta1 5.6 Mininet-WiFi Tutorial #4: Mobility 47 Running commands on nodes is standard Mininet feature but it is also an advanced topic. See the Mininet documentation20 for more details. You can run simple commands such as ping or iwconfig but more advance commands may require you to mount private directories21 for configuration or log files. 5.5.13 Mininet-WiFi and shell commands Mininet-WiFi manages the affect of range using code that calculates the ability of each node to connect with other nodes. However, Mininet-WiFi does not change the way networking works at the operating system level. So iw commands executed on nodes will override Mininet-WiFi and do not gather information generated by Mininet-WiFi about the network. I suggest you do not rely on iw commands. For example, the iw scan command will still show that sta1 can detect the SSIDs of all access points, even the access point ap2 which should be out of range. The iw link command will show the same signal strength regardless of how far the station is from the access point, while the Mininet-WiFi *info* command will show the calculated signal strength based on the propagation model and distance between nodes. For example, the iw command run on sta1 shows received signal strength is -30 dBm. This never changes no matter how far the station is from the access point. mininet-wifi> sta1 iw dev sta1-wlan0 link Connected to 02:00:00:00:00:00 (on sta1-wlan0) SSID: ssid-ap1 freq: 2412 RX: 164628 bytes (2993 packets) TX: 775 bytes (10 packets) signal: -30 dBm tx bitrate: 6.0 MBit/s bss flags: dtim period: beacon int: short-slot-time 2 100 The info command shows Mininet-WiFi’s calculated signal strength received by the station is -43.11 dBm. This value will change if you reposition the station. 5.5.14 Stop the tutorial Stop Mininet-Wifi and clean up the system with the following commands: mininet-wifi> exit wifi:~$ sudo mn -c 5.6 Mininet-WiFi Tutorial #4: Mobility The more interesting features provided by Mininet-WiFi support mobile stations moving around in virtual space. Mininet-Wifi provides new methods in its Python API, such as startMobility 20 https://github.com/mininet/mininet/wiki/Documentation 21 https://github.com/mininet/mininet/wiki/Introduction-to-Mininet#important-shared-filesystem Chapter 5. Tutorial 48 and Mobility, with which we may specify a wide variety of wireless LAN scenarios by controlling station movement, access point range, radio propagation models, and more. In this tutorial, we will create a scenario where one station moves about in space, and where it changes which access point it connects to, based on which access point is the closest. 5.6.1 Python API and mobility The Mininet-WiFi Python API adds new methods that allow the user to create stations that move around in virtual space when an emulation scenario is running. To move a station in a straight line, use the net.startMobility and net.mobility methods. See the example script wifiMobilty.py. For example, to move a station from one position to another over a period of 60 seconds, add the following lines to your script: net.startMobility( time=0 ) net.mobility( sta1, 'start', time=1, position='10,20,0' ) net.mobility( sta1, 'stop', time=59, position='30,50,0' ) net.stopMobility( time=60 ) Mininet-WiFi can also automatically move stations around based on predefined mobility models. See the example script mobilityModel.py. Available mobility models are: RandomWalk, TruncatedLevyWalk, RandomDirection, RandomWayPoint, GaussMarkov, ReferencePoint, and TimeVariantCommunity. For example, to move a station around in an area 60 meters by 60 meters with a minimum velocity of 0.1 meters per second and a maximum velocity of 0.2 meters per second, add the following line to your script: net.startMobility(time=0, model='RandomDirection', max_x=60, max_y=60, ,→ min_v=0.1, max_v=0.2) Mininet-WiFi will automatically connect and disconnect stations to and from access points based on either calculated signal strength or load level. See the example script associationControl.py. To use association control, add the AC parameter to the net.startMobility call. For example, to switch access points based on the “least loaded first” criteria, add the following line to your script: net.startMobility(time=0, model='RandomWayPoint', max_x=140, max_y=140, ,→ min_v=0.7, max_v=0.9, AC='llf') The valid values for the AC parameter are: • llf (Least-Loaded-First) • ssf (Strongest-Signal-First) When creating a scenario where stations will be mobile, we may set the range of the access points. In an example where we use “strongest signal first” as the Association Control method, the range of each access point will determine where handoffs occur between access points and which stations may connect to which access points. If you do not define the range, Mininet-WiFi assigns a default value. Mininet-WiFi supports more methods than mentioned above. See the example scripts (mentioned further below) for examples of using other methods. 5.6 Mininet-WiFi Tutorial #4: Mobility 5.6.2 49 Moving a station in virtual space A simple way to demonstrate how Mininet-WiFi implements scenarios with mobile stations that hand off between access points is to create a script that moves one station across a path that passes by three access points. The example below will create three access points – ap1, ap2, and ap3 – arranged in a line at differing distances from each other. It also creates a host h1 to serve as a test server and a mobile station sta1 and moves sta1 across space past all three access points. 1 # ! / usr / bin / python 2 3 4 5 6 7 from from from from from mininet mininet mininet mininet mininet . net import Mininet . node i m p o r t C o n t r o l l e r , OVSKernelAP . l i n k i m p o r t TCLink . c l i i m p o r t CLI . log import setLogLevel 8 9 def topology ( ) : 10 11 n e t = M i n i n e t ( c o n t r o l l e r = C o n t r o l l e r , l i n k =TCLink , a c c e s s P o i n t =OVSKernelAP ) 12 13 14 15 16 17 18 19 p r i n t " *** C r e a t i n g n o d e s " h1 = n e t . a d d H o s t ( ' h1 ' , mac= ' 0 0 : 0 0 : 0 0 : 0 0 : 0 0 : 0 1 ' , i p = ' 1 0 . 0 . 0 . 1 / 8 ' ) s t a 1 = n e t . a d d S t a t i o n ( ' s t a 1 ' , mac= ' 0 0 : 0 0 : 0 0 : 0 0 : 0 0 : 0 2 ' , i p = ' 1 0 . 0 . 0 . 2 / 8 ' r a n g e = ' 20 ' ) ap1 = n e t . a d d A c c e s s P o i n t ( ' ap1 ' , s s i d = ' ap1−s s i d ' , mode= ' g ' , c h a n n e l = p o s i t i o n = ' 3 0 , 5 0 , 0 ' , r a n g e = ' 30 ' ) ap2 = n e t . a d d A c c e s s P o i n t ( ' ap2 ' , s s i d = ' ap2−s s i d ' , mode= ' g ' , c h a n n e l = p o s i t i o n = ' 9 0 , 5 0 , 0 ' , r a n g e = ' 30 ' ) ap3 = n e t . a d d A c c e s s P o i n t ( ' ap3 ' , s s i d = ' ap3−s s i d ' , mode= ' g ' , c h a n n e l = p o s i t i o n = ' 1 3 0 , 5 0 , 0 ' , r a n g e = ' 30 ' ) c1 = n e t . a d d C o n t r o l l e r ( ' c1 ' , c o n t r o l l e r = C o n t r o l l e r ) 20 21 22 p r i n t " *** C o n f i g u r i n g w i f i n o d e s " net . configureWifiNodes ( ) 23 24 25 26 27 p r i n t " *** A s s o c i a t i n g and C r e a t i n g l i n k s " n e t . a d d L i n k ( ap1 , h1 ) n e t . a d d L i n k ( ap1 , ap2 ) n e t . a d d L i n k ( ap2 , ap3 ) 28 29 n e t . p l o t G r a p h ( max_x =160 , max_y = 16 0) 30 31 32 33 34 n e t . s t a r t M o b i l i t y ( t i m e =0 , AC= ' s s f ' ) n e t . m o b i l i t y ( s t a 1 , ' s t a r t ' , t i m e =20 , p o s i t i o n = ' 1 , 5 0 , 0 ' ) n e t . m o b i l i t y ( s t a 1 , ' s t o p ' , t i m e =79 , p o s i t i o n = ' 1 5 9 , 5 0 , 0 ' ) n e t . s t o p M o b i l i t y ( t i m e = 80 ) 35 36 37 38 39 40 41 p r i n t " *** net . build () c1 . s t a r t ( ) ap1 . s t a r t ( ap2 . s t a r t ( ap3 . s t a r t ( S t a r t i n g network " [ c1 ] ) [ c1 ] ) [ c1 ] ) 42 43 p r i n t " *** Running CLI " , '1 ' , '1 ' , '1 ' , Chapter 5. Tutorial 50 44 CLI ( n e t ) 45 46 47 p r i n t " *** S t o p p i n g n e t w o r k " net . stop () 48 49 50 51 i f __name__ == ' __main__ ' : setLogLevel ( ' info ' ) topology () codes/line.py Save the script and call in line.py. Make it executable, then run the command: wifi:~$ sudo ./line.py The Mininet-Wifi graph will appear (figure 5.8), showing the station and the access points. The station sta1 will sit still for 20 seconds, and then start to move across the graph from left to right for 60 seconds until it gets to the far side of the graph. The host h1 and the virtual Ethernet connections between h1, ap1 and between the three access points are not visible. 5.6.3 Re-starting the scenario This simple scenario has a discreet start and stop time so, if you wish to run it again, you need to quit Mininet-WiFi, and start the script again. For example, suppose the scenario is at its end, where the station is now at the far right of the graph window. To stop and start it again, enter the following commands: mininet-wifi> exit wifi:~$ sudo mn -c wifi:~$ sudo ./line.py Figure 5.8: The line.py script running 5.7 Mininet-WiFi Tutorial #5: VANETs (Veicular Ad Hoc Networks) 5.6.4 51 More Python functions When running a scenario with the mobility methods in the Python API, we have access to more information from Mininet-WiFi’s Python functions. To see all access points that are within range of a station such as sta1 at any time while the scenario is running, call the apsInRange function: mininet-wifi> py sta1.params['apsInRange'] [ ] 5.6.5 Test with iperf To see how the system responds to traffic, run some data between host h1 and station sta1 when the scenario is started. We have seen in previous examples how to use the ping program to create traffic. In this example, we will use the iperf program. First, start the line.py script again. Then start an iperf server on the station mininet-wifi> sta1 iperf --server Then open an xterm window on the host h1. mininet-wifi> xterm h1 From the xterm window, we will start the iperf client command and create a stream of data between h1 and sta1. On the h1 xterm, run the command: iperf --client 10.0.0.2 --time 60 --interval 2 Watch the iperf output as the station moves through the graph. When it passes from one access point to the next, the traffic will stop. To get the traffic running again, clear the flow tables in the access points. In the Mininet-WiFi CLI, run the command shown below: mininet-wifi> dpctl del-flows Traffic should start running again. As stated in Tutorial #2 above, we must clear flows after a hand off because the Mininet reference controller cannot respond correctly in a mobility scenario. The topic of configuring a remote controller to support a mobility scenario is outside the scope of this post. Clear the flows every time the station switches to the next access point. 5.6.6 Stop the tutorial Stop Mininet-Wifi and clean up the system with the following commands: mininet-wifi> exit wifi:~$ sudo mn -c 5.7 5.7.1 Mininet-WiFi Tutorial #5: VANETs (Veicular Ad Hoc Networks) Python API The Mininet-WiFi python API add a new node that allow the user to create cars that move around in virtual space when an emulation scenario is running. The function addCar() defines this new node and you can see an example in the file vanet.py into /examples. Chapter 5. Tutorial 52 v2STA-mp0 Vehicle2STA v2STA-eth0 v2SW-eth1 Vehicle2SW mesh v2SW-eth2 v2-eth0 Vehicle2 v2-wlan1 Car2 mesh v3STA-mp0 mesh controller (in-band) mesh Vehicle3STA v3STA-eth0 infra v3SW-eth1 Vehicle3SW v1STA-mp0 v3SW-eth2 RSU Vehicle1STA Vehicle3 v1SW-eth1 RSU controller (out-of-band) Vehicle1SW v1SW-eth2 v3-eth0 infra v1STA-eth0 v3-wlan1 infra Car3 v1-eth0 Vehicle1 v1-wlan1 Car1 Figure 5.9: Node Car Architecture 5.7.2 Node Car Architecture The architecture of the node car is depicted in Figure 5.9. In order to allow OpenFlow controllers to control simple nodes, like a car, it was necessary to create an architecture with a switch. Thus, every packet that comes from VehicleX needs to pass-trough VehicleXSW if the destination is a node in the wireless mesh network (like a Vehicle-to-Vehicle communication). The communication between cars and RSUs (Vehicle-to-Infrastructure), in turn, is done directly between VehicleX and the RSU. Figure 5.10: Integration with SUMO 5.8 Mininet-WiFi example scripts 5.7.3 5.8 53 Integration with SUMO (Simulation of Urban Mobility) Mininet-WiFi already has some integration with SUMO. An example can be found in /examples/sumoexperimental.py. Mininet-WiFi example scripts The Mininet-WiFi developers created many example scripts that show examples of most of the API extensions they added to Mininet. They placed these example scripts in the folder mininet-wifi/examples/. Try running these scripts to see what they do and look at the code to understand how each feature is implemented using the Python API. Some interesting Mininet-WiFi example scripts are: adhoc shows how to set up experiments with adhoc mode, where stations connect to each other without passing through an access point. simplewifitopology show the Python code that create the same topology as the default topology created my the mn –wifi command (two stations and one access point). position.py shows how to create a network where stations and access points are places in specific locations in virtual space. mobility and mobilityModel show how to move stations and how mobility models can be incorporated into scripts. associationControl shows how the different values of the AC parameter affect station handoffs to access points. mesh.py shows how to set up a mesh network of stations. handover.py shows how to create a simple mobility scenario where a station moves past two access points, causing the station to hand off from one to the other. multipleWlan.py shows how to create a station with more than one wireless LAN interface. propagationModel.py shows how to use propagation models that impact how stations and access points can communicate with each other over distance. authentication.py shows how to set up WiFi encryption and passwords on access points and stations. 5.9 Conclusion The tutorials presented above work demonstrate many of the unique functions offered by MininetWiFi. Each tutorial revealed more functionality and we stopped at the point where we were able to emulate mobility scenario featuring a WiFi station moving in a straight line past several wireless access points. R Thank you Brian Linkletter for this helpful tutorial. 6. Guided exercises/demo 6.1 Guided exercises/demo In general, you will learn in this chapter how the Mininet-WiFi wireless network emulator works. Guided exercises will be explored and pointers to source code for those interested in delving deeper into the system architecture will be also provided. The pointers include stretches of the code where the link (including the latency) can be customized. 6.1.1 Activity 1: Warming up First of all, you have to stop the network-manager: sudo service network-manager stop Then, create a simple topology with the command below: sudo mn --wifi The command above will start Mininet-WiFi and configure a small network with two stations, and one access point. Use the option --topo of mn command, and discover further the topology options. In Mininet-WiFi terminal (mininet-wifi>), execute the command nodes to observe the created network. Then, execute iwconfig to verify the association between the stations and ap1. mininet-wifi>sta1 iwconfig mininet-wifi>sta2 iwconfig mininet-wifi>sta1 ping sta2 Then, disconnect sta1 and confirm the disconnection: mininet-wifi>sta1 iw dev sta1-wlan0 disconnect mininet-wifi>sta1 iwconfig mininet-wifi>sta1 ping sta2 Chapter 6. Guided exercises/demo 56 Now, connect sta1 again: mininet-wifi>sta1 iw dev sta1-wlan0 connect my-ssid mininet-wifi>sta1 iwconfig mininet-wifi>sta1 ping sta2 6.1.2 Activity 2: Loading Network Topologies Running an example with the command below: sudo python examples/position.py Now, observe the position of sta1, sta2 and ap1: mininet-wifi>py sta1.params['position'] mininet-wifi>py sta2.params['position'] mininet-wifi>py ap1.params['position'] Observe the signal power as well: mininet-wifi>py sta1.params['rssi'] mininet-wifi>py sta2.params['rssi'] If you prefer, you can see the distance between two nodes with the following command: mininet-wifi>distance sta1 ap1 mininet-wifi>distance sta1 sta2 ∗ Question 2.1: What is the observed bandwidth between sta1 and sta2? Tip: try iperf sta1 sta2 Now, move sta1 to another position: mininet-wifi>py sta1.setPosition('70,40,0') ∗ Question 2.2: What happened with the association between sta1 and ap1? Tip: try sta1 iwconfig Finally, increase the signal range of ap1: mininet-wifi>py ap1.setRange(60) ∗ Question 2.3: What happened with the association between sta1 and ap1 now? ∗ Question 2.4: Now, observe the bandwidth between sta1 and sta2 again. What can we conclude? 6.2 Further hands-on 6.1.3 57 Activity 3: Customizing the Wireless Channel Mininet-WiFi relies on the configuration of Linux TC (by default) to control the wireless channel properties, such as bandwidth, packet loss, delay and latency. Please see the equations in mininet/wifiLink.py (refer to equationBW, equationLoss, equationDelay and equationLatency. Those equations can be customized by calling setChannelEquation(), for example: net.setChannelEquation(bw='value.rate * (1.1 ** -dist)', loss='(dist * ,→ 2)/100', delay='(dist / 10) + 1', latency='2 + dist') Alternatively, a new approach called wmediumd has been implemented, a wireless medium simulation tool for Linux, based on the netlink API implemented in the mac80211_hwsim kernel driver. A couple of sample files that use wmediumd are available at /examples. ∗ Question 3.1: Run position.py again and try sta1 tc qdisc before and after moving sta1 to the new position. What do you can conclude about the configuration applied by tc? 6.2 Further hands-on (Further hands-on exercises proposed to be carried by the attendees on their own and at their pace. A number practical exercises will be proposed where mobility and/or distance (or poor signal) among mobile nodes may impact latency and bandwidth, consequently the communication between two nodes.) 6.2.1 Activity 4: Mobility Open examples/mobilityModel.py with any text editor and change the velocity of stations as below: from: net.startMobility(time=0, model='RandomDirection', max_x=100, ,→ max_y=100, min_v=0.5, max_v=0.8) to: net.startMobility(time=0, model='RandomDirection', max_x=100, ,→ max_y=100, min_v=0.1, max_v=0.1) Run examples/mobilityModel.py and change the signal range of ap1: python examples/mobilityModel.py mininet-wifi>py ap1.setRange(60) Then, ping sta1 and sta2: mininet-wifi>sta1 ping sta2 ∗ Question 4.1: What can you conclude about the latency? Tip: you can issue sta1 tc qdisc, repeatedly, to see the values applied by tc. 6.2.2 Activity 5: Received Signal Strength Open examples/position.py with any text editor and add sta3 at position=’10,10,10’ and set max_z=100 in order to plot a 3d graph. Then, run examples/position.py. Chapter 6. Guided exercises/demo 58 ∗ Question 5.1: What is the received signal strength indicator (RSSI) observed from sta3? ∗ Question 5.2: What is the average ping response time between sta2 and sta1? And sta3 and sta1? Note: define the number of packets to 10 (ping -c10). 6.3 OpenFlow You will learn with this activity some basic concepts of the OpenFlow protocol, such as idle/hard timeout and identify the impact of the mobility in the communication. 6.3.1 Activity 6: Mobility and OpenFlow First of all you have to get the code from https://github.com/ramonfontes/reproducible-research/ blob/master/mininet-wifi/ACROSS-Sweden-2017/handover.py and then run it with the command below (the content of handover.py is also available in Code 10.1): sudo python handover.py Now, keep h1 pinging to sta1 mininet-wifi>h1 ping sta1 ∗ Question 6.1: As you can see, h1 cannot reach sta1 when sta1 goes to ap2. Why? Two important commands should help you to answer this question: mininet-wifi>links mininet-wifi>sh ovs-ofctl dump-flows s3 Tip: Observe both idle_timeout and idle_age. ∗ Question 6.2: Now you know the answer to Question 6.1, how could sta1 be reached by h1? 7. Reproducible Research The code and instructions used in this section can be found at https://github.com/ramonfontes/ reproducible-research 7.1 SwitchOn 2015 Extended abstract - Towards an Emulator for Software Defined Wireless Networks Firstly, you have to get the code at https://github.com/ramonfontes/reproducible-research/ blob/master/mininet-wifi/SWITCHON-2015, then execute it: sudo python allWirelessNetworksAroundUs.py mininet-wifi> xterm sta1 h1 On sta1: cvlc -vvv v4l2:///dev/video0 --input-slave=alsa://hw:1,0 --mtu 1000 ,→ --sout'#transcode{vcodec=mp4v,vb=800,scale=1,acodec=mpga,ab=128,channels=1}: ,→ duplicate{dst=display,dst=rtp{sdp=rtsp://10.0.0.10:8080/helmet.sdp}' On h1: cvlc rtsp://10.0.0.10:8080/helmet.sdp 7.2 SBRC 2016 DEMO - Mininet-WiFi: Emulação de Redes Sem Fio Definidas por Software com suporte a Mobilidade Codes necessary to reproduce this paper are available at https://github.com/ramonfontes/ reproducible-research/tree/master/mininet-wifi/SBRC-2016 and https://github.com/ ramonfontes/reproducible-research/blob/master/mininet-wifi/SBRC-2016/wifiStationsAndHosts. py. 60 7.2.1 Chapter 7. Reproducible Research Case 1 - Simple test sudo mn --wifi mininet-wifi>sta1 ping sta2 mininet-wifi>sta1 iwconfig mininet-wifi>sta2 iwconfig 7.2.2 Case 2 (1/2) - Communication among stations and hosts/Verifying flow table sudo python examples/wifiStationsAndHosts.py mininet-wifi>nodes mininet-wifi>sh ovs-ofctl dump-flows ap1 mininet-wifi>sta1 ping h3 mininet-wifi>sh ovs-ofctl dump-flows ap1 7.2.3 Case 2 (2/2) - Changing the controller (from reference to external controller) Open the code examples/wifiStationsAndHosts.py and make the following changes: from: net = Mininet( controller=Controller, link=TCLink, ,→ switch=OVSKernelSwitch ) to: net = Mininet( controller=RemoteController, link=TCLink, ,→ switch=OVSKernelSwitch ) from: c0 = net.addController('c0', controller=Controller, ip='127.0.0.1' ) to: c0 = net.addController('c0', controller=RemoteController, ip='127.0.0.1' ,→ ) sudo python examples/wifiStationsAndHosts.py mininet-wifi>sta1 ping h3 #Why there is no communication? 7.2.4 Case 3 - Handover sudo python examples/handover.py mininet-wifi>sta1 iwconfig mininet-wifi>sta1 ping sta2 #here I suggest you wait sta1 reaches ap2 ,→ before going to the next step mininet-wifi>sta1 iwconfig 7.2.5 Case 4 - Changes at runtime sudo python examples/position.py mininet-wifi>sta1 iwconfig mininet-wifi>sta1 ping sta2 mininet-wifi>py sta1.setPosition('70,40,0') mininet-wifi>sta1 iwconfig mininet-wifi>sta1 ping sta2 mininet-wifi>py ap1.setRange(60) mininet-wifi>sta1 iwconfig mininet-wifi>sta1 ping sta2 7.3 SIGCOMM 2016 7.2.6 61 Case 5 - Bridging physical and virtual emulated environments sudo systemctl stop network-manager Edit sbrc.py: from: phyap1 = net.addPhysicalBaseStation( 'phyap1', ssid= ,→ 'SBRC16-MininetWiFi', mode='g', channel='1', position='50,115,0', ,→ wlan='wlan11' ) to: wlan11 to your usb wlan interface. Then, sudo python sbrc.py At this moment users attending the conference will be invited to connect their mobile devices into the physical/emulated environment. 7.3 SIGCOMM 2016 Demo: Mininet-WiFi: A Platform for Hybrid Physical-Virtual Software-Defined Wireless Networking Research Requirements to reproduce: • WiFi interface + (other WiFi or ethernet interface) • Floodlight OpenFlow controller • ofsoftswitch13 (you may install it with util/install.sh -3f ) - https://github.com/CPqD/ofsoftswitch13 • Speedtest-cli • Codes are available at https://github.com/ramonfontes/reproducible-research/ tree/master/mininet-wifi/SIGCOMM-2016 Important (changes in code - You have to set both Internet and wlan interfaces): internetIface = 'eth0' # wired/wireless card. usbDongleIface = 'wlan0' # wifi interface. Next, executing the Floodlight OpenFlow controller: sudo java -jar target/floodlight.jar Then, sudo py hybridVirtualPhysical.py mininet-wifi> sh ./rule.hybridVirtualPhysical Despite the content of rule.hybridVirtualPhysical is included in hybridVirtualPhysical.py, we have faced some troubles in floodlight controller. Thus, probably you have to execute rule.hybridVirtualPhysical after executing hybridVirtualPhysical.py. Now, stations should be able to communicate with each other and with the Internet. You may use any station connected to any Access Point and try it out: mininet-wifi>xterm $station $station>speedtest-cli Chapter 7. Reproducible Research 62 Using speedtest-cli you can test both Download and Upload speed of your Internet connection. The available bandwidth is controlled by OpenFlow meter entries. There is a web server accessible at 10.0.0.111 and according rules applied in rule.hybridVirtualPhysical, if you access 10.0.0.109 the traffic will be redirect to 10.0.0.111. Useful commands: sta1 iw dev sta1-wlan0 sh dpctl unix:/tmp/ap3 sh dpctl unix:/tmp/ap3 sh dpctl unix:/tmp/ap3 7.4 mpath dump #verify mesh routing information stats-flow stats-meter meter-config From Theory to Experimental Evaluation: Resource Management in SoftwareDefined Vehicular Networks Firstly, you have to get vanet.py at https://github.com/ramonfontes/reproducible-research/ blob/master/mininet-wifi/IEEE-Access-2017/vanet.py sudo python vanet.py Please consider to watch: https://www.youtube.com/watch?v=kO3O9EwrP_s 7.5 The Computer Journal - How far can we go? Towards Realistic SoftwareDefined Wireless Networking Experiments Codes necessary to reproduce this paper are available at https://github.com/ramonfontes/ reproducible-research/tree/master/mininet-wifi/The-Computer-Journal-2017 7.5.1 Wireless n-Casting Requirements: Floodlight controller. In order to reproduce this case, please follow the instructions below: First, run the controller: sudo java -jar target/floodlight.jar start the topology: sudo python ncasting.py and finally install the rules: sudo python ncasting-controller.py 7.5 The Computer Journal - How far can we go? Towards Realistic Software-Defined Wireless Networking Experiments 7.5.2 63 Multipath TCP Requirements: You have to install mptcp and ifstat to reproduce this use case. In order to allow the communication we use pox controller with spanning tree enabled. This command can be used to enable spanning tree: ./pox.py forwarding.l2_learning openflow.spanning_tree --hold-down log.level ,→ --DEBUG samples.pretty_log openflow.discovery host_tracker ,→ info.packet_dump Then, start the environment in a new terminal and run some commands with xterm: sudo python mptcp.py mininet-wifi>xterm sta1 sta1 h10 h10 Node: h10 (terminal1)$ifstat Node: sta1 (terminal1)$ifstat Node: h10 (terminal2)$iperf -s Node: sta1 (terminal2)$iperf -c 192.168.1.254 7.5.3 Hybrid Physical-Virtual Environment See Section 7.3. 7.5.4 SSID-based Flow Abstraction Requirements: ofsoftswitch13 In order reproduce this case you have to run the following code: sudo python forwardingBySSID.py Then, you may run any application (e.g., Iperf) to test the available bandwidth for any SSID. Alternatively, you might run dpctl to verify meter table configuration. mininet-wifi> sh dpctl unix:/tmp/ap1 meter-config 7.5.5 EXPERIMENTAL VALIDATION: Propagation Model Consider to use the file propagationModelCase.py if you want to reproduce the results. 7.5.6 EXPERIMENTAL VALIDATION: Simple File Transfer Consider to use the files fileTransferring.py and fileTransferring.cc if you want to reproduce the results. 7.5.7 EXPERIMENTAL VALIDATION: Replaying Network Conditions Consider to use files into the directory replayingNetwork/ if you want to reproduce the results. 8. Publications 8.1 SDN For Wireless 2015 Exhibit Fontes, R. R., Afzal, S., Brito, S. H. B., Santos, M., Rothenberg, C. E. “Towards an Emulator for Software Defined Wireless Networks“. In EAI International Conference on Software Defined Wireless Networks and Cognitive Technologies for IoT. Rome, Italy, Oct 2015. 8.2 CNSM 2015 - Best Paper Award! This paper explains the basic Mininet-WiFi design and useful Case Studies. Fontes, R. R., Afzal, S., Brito, S. H. B., Santos, M., Rothenberg, C. E. “Mininet-WiFi: Emulating Software-Defined Wireless Networks“. In 2nd International Workshop on Management of SDN and NFV Systems 2015. Barcelona, Spain, Nov 2015. 8.3 SwitchOn 2015 This paper presents a demo use case in a mobile video streaming scenario to showcase the ability of Mininet-WiFi to emulate the wireless channel in terms of bandwidth, packet loss, and delay variations as a function of the distance between the communicating parties. Fontes, R. R., Rothenberg, C. E. Towards an Emulator for Software-Defined Wireless Networks. In: SwitchOn 2015, São Paulo – SP – Brazil. 8.4 SBRC 2016 DEMO Ramon dos Reis Fontes and Christian Esteve Rothenberg. Mininet-WiFi: Emulação de Redes Sem Fio Definidas por Software com suporte a Mobilidade. In Simpósio Brasileiro de Redes de Computadores e Sistemas Distribuídos (SBRC 2016) - Salão de Ferramentas, 2016, Salvador - BA Brazil. 66 8.5 Chapter 8. Publications SIGCOMM 2016 DEMO Ramon dos Reis Fontes and Christian Esteve Rothenberg. Mininet-WiFi: A Platform for Hybrid Physical-Virtual Software-Defined Wireless Networking Research (SIGCOMM 2016) - 2016, Florianopolis - ES - Brazil. 8.6 Institute of Electrical and Electronics Engineers - IEEE 2017 In this paper, we enumerate the potentials of software-defined vehicular networks, analyse the need of rethinking the traditional SDN approach from theoretical and practical standpoints when applied in this application context, and present an emulation approach based on the proposed node car architecture in Mininet- WiFi to showcase the applicability and some expected benefits of SDN in a selected use case scenario. Ramon dos Reis Fontes and Claudia Campolo and Christian E. Rothenberg and Antonella Molinaro. From Theory to Experimental Evaluation: Resource Management in Software-Defined Vehicular Networks (IEEE Access 2017), DOI: 10.1109/access.2017.2671030. 8.7 The Computer Journal 2017 Ramon dos Reis Fontes and Mohamed Mahfoudi and Walid Dabbous and Thierry Turletti and Christian Rothenberg. How Far Can We Go? Towards Realistic Software-Defined Wireless Networking Experiments, Oxford University Press (OUP), DOI: 10.1093/comjnl/bxx023. 9. Acknowledgment • This project is partially supported by INRIA - Institut National de Recherche en Informatique et en Automatique, in Sophia Antipolis, France and FAPESP - Fundação de Amparo à Pesquisa do Estado de São Paulo, in Sao Paulo, Brazil. • We thank Dr. Chih-Heng Ke, from Department of Computer Science and Information Engineering, National Quemoy University, Kinmen, Taiwan, for all our discussion at the beginning of this work. • We thank Brian Linkletter - brianlinkletter.com for the tutorial presented at the chapter 5. • We thank Patrick Große, member of http://www.uni-muenster.de/Comsys/en/ for integrating Mininet-WiFi with wmediumd (section 1.5.2). • We thank all users who participate of our mailing list for collaborating in the development of this work. 10. Appendix 10.1 handover.py 1 # ! / usr / bin / python 2 3 ' Example f o r h a n d o v e r ' 4 5 6 7 8 9 from from from from from mininet mininet mininet mininet mininet . net import Mininet . node i m p o r t C o n t r o l l e r , OVSKernelSwitch , OVSKernelAP . l i n k i m p o r t TCLink . c l i i m p o r t CLI . log import setLogLevel 10 11 def topology ( ) : 12 13 14 " Create a network . " n e t = M i n i n e t ( c o n t r o l l e r = C o n t r o l l e r , l i n k =TCLink , s w i t c h = OVSKernelSwitch , a c c e s s P o i n t =OVSKernelAP ) 15 16 17 18 19 20 21 22 p r i n t " *** C r e a t i n g n o d e s " s t a 1 = n e t . a d d S t a t i o n ( ' s t a 1 ' , mac= ' 0 0 : 0 0 : 0 0 : 0 0 : 0 0 : 0 1 ' , i p = ' 1 0 . 0 . 0 . 1 / 8 ' ) ap1 = n e t . a d d A c c e s s P o i n t ( ' ap1 ' , s s i d = ' new−s s i d 1 ' , mode= ' g ' , c h a n n e l = ' 1 ' , p o s i t i o n = ' 15 ,30 ,0 ' ) ap2 = n e t . a d d A c c e s s P o i n t ( ' ap2 ' , s s i d = ' new−s s i d 1 ' , mode= ' g ' , c h a n n e l = ' 6 ' , p o s i t i o n = ' 55 ,30 ,0 ' ) s3 = n e t . addSwitch ( ' s3 ' ) h1 = n e t . a d d H o s t ( ' h1 ' , mac= ' 0 0 : 0 0 : 0 0 : 0 0 : 0 0 : 0 2 ' , i p = ' 1 0 . 0 . 0 . 2 / 8 ' ) c1 = n e t . a d d C o n t r o l l e r ( ' c1 ' , c o n t r o l l e r = C o n t r o l l e r , p o r t = 66 53 ) 23 24 25 p r i n t " *** C o n f i g u r i n g WiFi Nodes " net . configureWifiNodes ( ) 26 27 28 29 h1 . p l o t ( p o s i t i o n = ' 3 5 , 9 0 , 0 ' ) s3 . p l o t ( p o s i t i o n = ' 35 ,80 ,0 ' ) Chapter 10. Appendix 70 30 31 32 33 p r i n t " *** C r e a t i n g l i n k s " n e t . a d d L i n k ( ap1 , s 3 ) n e t . a d d L i n k ( ap2 , s 3 ) n e t . a d d L i n k ( h1 , s 3 ) 34 35 36 """ p l o t t i n g graph """ n e t . p l o t G r a p h ( max_x =100 , max_y = 10 0) 37 38 39 40 41 net net net net . . . . s t a r t M o b i l i t y ( time =0) m o b i l i t y ( s t a 1 , ' s t a r t ' , t i m e =1 , p o s i t i o n = ' 1 0 , 3 0 , 0 ' ) m o b i l i t y ( s t a 1 , ' s t o p ' , t i m e =80 , p o s i t i o n = ' 6 0 , 3 0 , 0 ' ) s t o p M o b i l i t y ( t i m e = 80 ) 42 43 44 45 46 47 48 p r i n t " *** S t a r t i n g n e t w o r k " net . build () c1 . s t a r t ( ) ap1 . s t a r t ( [ c1 ] ) ap2 . s t a r t ( [ c1 ] ) s 3 . s t a r t ( [ c1 ] ) 49 50 51 p r i n t " *** Running CLI " CLI ( n e t ) 52 53 54 p r i n t " *** S t o p p i n g n e t w o r k " net . stop () 55 56 57 58 i f __name__ == ' __main__ ' : setLogLevel ( ' info ' ) topology () Code 10.1: handover.py
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 70 Page Mode : UseOutlines Author : Title : Subject : Creator : LaTeX with hyperref package Producer : pdfTeX-1.40.17 Create Date : 2018:01:21 12:47:46Z Modify Date : 2018:01:21 12:47:46Z Trapped : False PTEX Fullbanner : This is pdfTeX, Version 3.14159265-2.6-1.40.17 (TeX Live 2016/Debian) kpathsea version 6.2.2EXIF Metadata provided by EXIF.tools