Peiker acustic V1231-0 LTE-Advanced Network Access Device User Manual
Peiker acustic GmbH & Co. KG LTE-Advanced Network Access Device
User Manual
V123x-0 (LTE-NAD-A) User manual Peiker product IDs: 2189-230-042-00 2189-231-042-00 2189-232-042-00 2189-233-042-00 Revision: Date: 1.4 August 2017 (V1230-0) (V1231-0) (V1232-0) (V1233-0) _______________________________________________________________________________________________________________ Seite 1 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Revision History Date 28.02.2017 01.03.2017 06.03.2017 Revision 1.0 1.1 1.2 Name mgi phse mgi 08.08.2017 1.3 phse 04.09.2017 1.4 phse Comment Initial document based on V123x-1 documents Some rewording as well as some corrections Model name changed to V123x-0 Renumbering of some sections Added new section called “Maximum TX Output Power” Updated the temp range table from section 2.12.1 Reworked section 6 Updated the pin-out table _______________________________________________________________________________________________________________ Seite 2 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Content Introduction ..........................................................................................................................................4 1.1 Scope ..................................................................................................................................................4 1.2 Audience ............................................................................................................................................4 1.3 Contact information, Support .........................................................................................................4 Product Overview ................................................................................................................................5 2.1 Product Variants................................................................................................................................5 2.2 Supported Technology/Frequency Bands .....................................................................................5 2.3 Maximum TX Output Power ............................................................................................................5 2.5 Features .............................................................................................................................................6 2.6 Certifications / Approvals.................................................................................................................7 2.8 Connectors .........................................................................................................................................7 2.8.1 Module Signal and RF Connectors ..........................................................................................7 2.8.2 Ground and Heat Dissipation Connectors..............................................................................7 2.9 Main Interfaces .................................................................................................................................8 2.9.1 USB ..............................................................................................................................................8 2.9.2 SIM Interface .............................................................................................................................8 2.9.3 Power on.....................................................................................................................................8 2.9.4 Reset ...........................................................................................................................................8 2.9.5 GPIOs ..........................................................................................................................................9 2.9.6 GSBIs...........................................................................................................................................9 2.9.7 Module Pin-out.........................................................................................................................10 2.10 Supply Voltage ..............................................................................................................................15 2.11 Power Consumption .....................................................................................................................15 2.12 Environmental Specification ........................................................................................................16 2.12.1 Temperature Range ..............................................................................................................16 Evaluation Kit .....................................................................................................................................17 AT Command interface .....................................................................................................................20 Safety Recommendations according to EN60950-1 .....................................................................22 RED/FCC/IC Regulatory Notices ......................................................................................................23 6.1 Modifications ..............................................................................................................................23 6.2 Interference................................................................................................................................23 6.3 FCC Class B Digital Device .......................................................................................................23 6.3 OEM Responsibilities .................................................................................................................24 List of Acronyms ................................................................................................................................25 _______________________________________________________________________________________________________________ Seite 3 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 1 Introduction 1.1 Scope This document gives an overview about electrical, mechanical and functional details of the peiker LTENAD-A V123x-0 modules. 1.2 Audience Information to integrate the module in some other applications. 1.3 Contact information, Support peiker acustic GmbH & Co KG Max-Planck Street 32 D-61381 Friedrichsdorf / Ts. Germany http://www.peiker.de info@peiker.de _______________________________________________________________________________________________________________ Seite 4 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 2 Product Overview 2.1 Product Variants The LTE-NAD-A module family consists of four regional variants: Peiker product # 2189-230-042-00 (V1230-0) 2189-231-042-00 (V1231-0) 2189-232-042-00 (V1232-0) 2189-233-042-00 (V1233-0) Module configuration ECE configuration NA configuration CHN configuration RoW configuration 2.2 Supported Technology/Frequency Bands V1230-0 GSM Bands WCDMA Bands LTE Bands 900MHz and 1800MHz FDD1, FDD3 and FDD8 eFDD1, eFDD3, eFDD7, eFDD20, eFDD28A, eFDD32 and eTTD38 V1231-0 GSM Bands WCDMA Bands LTE Bands 850MHz and 1900MHz FDD2, FDD4 and FDD5 eFDD2, eFDD4, eFDD5, eFDD7, eFDD12 and eFDD29 V1232-0 GSM Bands WCDMA Bands LTE Bands 900MHz and 1800MHz FDD1 and FDD8 eFDD1, eFDD3, eFDD7, eTTD38, eTTD40 and eTTD41 V1233-0 GSM Bands WCDMA Bands LTE Bands 850MHz, 900MHz, 1800MHz and 1900MHz FDD1, FDD2, FDD3, FDD5, FDD6, FDD8 and FDD19 eFDD1, eFDD3, eFDD5, eFDD7, eFDD8, eFDD9, eFDD19, eFDD21, eFDD28B and eTTD40 2.3 Maximum TX Output Power GSM 850 and GSM 900 (PCL=5, 1 UL TS): 34,5 dBm GSM 1800 and GSM 1900 (PCL=5, 1 UL TS): 31,5 dBm GPRS 850 and GPRS 900 (PCL=5, 4 UL TS): 29 dBm GPRS 1800 and GPRS 1900 (PCL=0, 4 UL TS): 26 dBm EDGE 850 and EDGE 900 (PCL=8, 4 UL TS): 23 dBm _______________________________________________________________________________________________________________ Seite 5 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe EDGE 1800 and EDGE 1900 (PCL=2, 4 UL TS): 22 dBm WCDMA (all supported frequency bands): 25 dBm LTE (all supported frequency bands): 25 dBm 2.4 Module to Hosts Mapping The below table shows the mapping between the module variants and the host/ATM-02 devices: Module Host devices embedding this module variant V1230-0 V1231-0 V1232-0 V1233-0 ATM-02-ECE-R1 and ATM-02-ECE-T1 ATM-02-US-R1 and ATM-02-US-T1 ATM-02-CHN-R1 and ATM-02-CHN-T1 ATM-02-ROW-R1 and ATM-02-ROW-T1 2.5 Features Features - Same footprint and pin-out (all modules) - Voice and data calls (all modules) - IMS/VoLTE - 4G: Rel-11, 3G/3G+: Rel-9, 2G: Rel-9 - DTM/eDTM (all modules) - Standalone GPS, GLONASS, Galileo, SBAS, QZSS and BeiDou Data rates - GPRS/EDGE: Multislot class 33 - WCDMA: DL /UL up to 384kbps HSPA+: Category 24 in DL using 64 QAM and Dual-Cell; Up to 42 Mbps (All modules except V1231-0) Category 14 in DL using 64 QAM; Up to 21 Mbps (V1231-0) Category 6 in UL using 16 QAM; Up to 5.76 Mbps (All modules) - LTE Category 11: Up to 450 Mbps in DL using 3 CCs, up to 75 Mbps in UL (All modules) Power Classes - LTE: All supported bands, Power Class 3 - WCDMA: All supported bands, Power Class 3 - EDGE: 850/900/1800/1900, Power Class E2 - GSM/GPRS: 850/900, Power Class 4 - GSM/GPRS: 1800/1900, Power Class 1 Dimension and Weight - Dimensions: 35mm x 38mm x 4,35mm - Weight < 10 grams _______________________________________________________________________________________________________________ Seite 6 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 2.6 Certifications / Approvals V1230-0 V1231-0 V1232-0 V1233-0 GCF RED Planned Planned PTCRB FCC/IC AT&T Planned Planned Planned Planned Planned Planned 2.7 HW Features Qualcomm X12 LTE, 20nmSoC MDM9240 Baseband / PMIC: PMD9645 / WTR3925 WTR4905 Cortex-A7 up to 1.2 GHz Modem and low power audio sub systems: QDSP6 processor at up to 850 MHz (turbo) RPM Resource and power manager: Cortex M3 up to 100 MHz 4Gb NAND Flash 2Gb LPDDR2 SDRAM 19.2MHz clock reference GPS, GLONASS, BeiDou, and Galileo 2.8 Connectors 2.8.1 Module Signal and RF Connectors LTE-NAD-A has 172 signal pins (2xAA and 2xBB) connector pads with 1.0mm pitch. The signal pads are located close to the board edges. There are three antenna pads, each collocated by RF GND connectors Main transmit and receive antenna – pin LGA_PRX_ANT Diversity antenna for WCDMA respective MIMO antenna for LTE – pin LGA_DRX_ANT_IN GNSS antenna for both GPS and GLONASS – pin LGA_GPS_DRX_ANT 2.8.2 Ground and Heat Dissipation Connectors To support the usage of module under complicated thermal conditions, there are a number of large grounded pads in the center of PCB. These pads are dedicated ground pads to transfer heat dissipation to a carrier board. This should be especially considered by customer designs. A reference design showing landing patterns and PCB stack-up is available on request. _______________________________________________________________________________________________________________ Seite 7 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 2.9 Main Interfaces 2.9.1 USB LTE-NAD-A has one USB2.0 OTG high speed (480MBit) compliant interface including the PHY. This IF consists of four signals: USB_HS_DP: USB_HS_DM USB_HS_ID: MDM_VBUS_DET: USB USB USB USB Data Plus signal Data Minus signal high-speed data - ID Voltage Supply LTE-NAD-A has one USB3.0 high speed (480MBit) compliant interface including the PHY. This IF consists of four signals: MDM_USB_SS_RX_P: MDM_USB_SS_RX_M MDM_USB_SS_TX_P: MDM_USB_SS_TX_M: USB USB USB USB 3.0 3.0 3.0 3.0 receive – plus receive – minus transmit – plus transmit – minus A dynamic reconfiguration between USB-Host or USB-Device is not foreseen. LTE-NAD-A can be configured to USB-Host or USB-Device by insertion of a resistor on the USB_ID line. 2.9.2 SIM Interface LTE-NAD-A has two SIM interfaces that are compatible for both 1.8V and 3V SIM Cards. Those IFs consist of the following signals: VREF_UIM1 / VREF_UIM2 UIM1_CLK / UIM2_CLK UIM1_DETECT / UIM2_DETECT UIM1_DATA / UIM2_DATA UIM1_RESET / UIM2_RESET The data rate of the SIM IF is up to 4 Mbps, so HW designers should take care of the length and routing of the SIM IF to prevent potential EMC problems. 2.9.3 Power on The signal PON_1 is used to switch on LTE-NAD-A. As PON_1 is pulled against VMAIN internally, it is recommended to pull this input against GND using an open collector or open drain output only. 2.9.4 Reset PMD_RESIN_N is used to reset LTE-NAD-A. As PMD_RES_IN is pulled against VMAIN internally, it is recommended to pull this input against GND using an open collector or open drain output only. _______________________________________________________________________________________________________________ Seite 8 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 2.9.5 GPIOs There are 51 GPIOs available on LTE-NAD-A, some of them being part of the five GSBIs (see next section). They are used for different interfaces (see Table 1 and the following sections). For allocation of GPIOs/GSBIs to different configurations, please contact us. GPIOs and GSBIs share the same output pins and may not available when used as GSBI configuration. The following GPIOs do not belong to a GSBI bundle: GPIO 47, 72, 82, 25, 28, 26, 27, 84, 80, 21, 23, 22, 24, 20, 1, 78, 79, 85, 86, 69, 0, 77, 65, 61, 68, 51, 54, 73, 48, 49, 53. The following GPIOs belongs to a GSBI bundle: GPIO 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 29, 30. 2.9.6 GSBIs Five GSBIs (General Serial Bus Interfaces) are available in total, each of them consisting of four GPIOs. The reference voltage of the GSBIs is 1.8V. Available signals on GSBI bundles at the board to board connector: GSBI1: GSBI2: GSBI3: GSBI4: GSBI5: GSBI1_0, GSBI2_0, GSBI3_0, GSBI4_0, GSBI5_0, GSBI1_1, GSBI2_1, GSBI3_1, GSBI4_1, GSBI5_1, GSBI1_2, GSBI2_2, GSBI3_2, GSBI4_2, GSBI5_2, GSBI1_3 GSBI2_3 GSBI3_3 GSBI4_3 GSBI5_3 (GPIO_29, 30, 2, 3) (GPIO_4, 5, 6, 7) (GPIO_8, 9, 10, 11) (GPIO_12, 13, 14, 15) (GPIO_16, 17, 18, 19) _______________________________________________________________________________________________________________ Seite 9 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 2.9.7 Module Pin-out Table 1 Module Pin-out Pin numbe Category 9x40 Pin name Description GND GND Ground USB3.0 MDM_USB_SS_TX_M USB 3.0 transmit – minus 105 USB3.0 MDM_USB_SS_TX_P USB 3.0 transmit – plus GND GND Ground 106 GND GND Ground USB3.0 (9x40) MDM_USB_SS_RX_M USB 3.0 receive – minus 107 USB3.0 (9x40) MDM_USB_SS_RX_P USB 3.0 receive – plus GND GND Ground 108 GND GND Ground PCIE/WLAN IF PCIE_REFCLK_M PCIe reference clock – minus 109 PCIE/WLAN IF PCIE_REFCLK_P PCIe reference clock – plus GND GND Ground 110 GND GND Ground PCIE/WLAN IF PCIE_TX_M 111 PCIE/WLAN IF PCIE_TX_P PCIe transmit – plus GND GND Ground 112 GND GND Ground 10 PCIE/WLAN IF PCIE_RX_M 113 PCIE/WLAN IF PCIE_RX_P 11 GND GND Ground 114 GND GND Ground 12 USB PMD_USB_ID USB high-speed data – ID 115 USB USB2_EXT_VBUS_DET External USB Vbus detection 13 GND GND Ground 116 GPIO GPIO_86 Configurable I/O 14 Reserved Reserved Inter-chip communication 117 GND GND Ground 15 Reserved Reserved Inter-chip communication 118 GND GND Ground 16 USB MDM_USB_HS_DP USB high-speed data – plus 119 USB MDM_USB_HS_DM USB high-speed data – minus 17 GND GND Ground PCIe transmit – minus PCIe receive – minus PCIe receive – plus _______________________________________________________________________________________________________________ Seite 10 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 120 SDIO IF/eMMC GPIO_96 / MDM_SDC1_DATA_4 Secure digital controller data bit 4 18 SDIO IF/eMMC GPIO_97 / MDM_SDC1_DATA_5 Secure digital controller data bit 5 121 SDIO IF/eMMC GPIO_98 / MDM_SDC1_DATA_6 Secure digital controller data bit 6 19 SDIO IF/eMMC GPIO_99 / MDM_SDC1_DATA_7 Secure digital controller data bit 7 122 SDIO IF GPIO_81 / SD_CARD_DET_N Secure digital card detection 20 SDIO IF MDM_SDC1_DATA_0 Secure digital controller data bit 0 123 SDIO IF MDM_SDC1_DATA_1 Secure digital controller data bit 1 21 SDIO IF MDM_SDC1_DATA_2 Secure digital controller data bit 2 124 SDIO IF MDM_SDC1_DATA_3 Secure digital controller data bit 3 22 GND GND Ground 125 SDIO IF MDM_SDC1_CMD Secure digital controller 2 command 23 SDIO IF MDM_SDC1_CLK Secure digital controller 2 clock 126 SIM1 VREG_L11_UIM1 Reference for UIM I/O pads GND Ground 24 127 SIM1 GPIO_79 / MDM_UIM1_CLK UIM1 clock 25 SIM1 GPIO_78 /MDM_UIM1_RESET UIM1 reset 128 SIM1 GPIO_77 / MDM_UIM1_DETECT UIM1 detect (non dual voltage) 26 SIM1 GPIO_76 /MDM_UIM1_DATA UIM1 data 27 GND GND Ground 28 I2S GPIO_15 / I2S_CLK I2S Data Clock 129 GND GND Ground 29 I2S MDM_MCLK Audio Master clock 130 GND GND Ground 30 I2S GPIO_12 / I2S_WS I2S word select 131 I2S GPIO_13 / I2S_DO I2S Data Output 31 I2S GPIO_14 / I2S_DI I2S Data Input 132 GND GND Ground 32 GPIO_19 / ANT_SW_2 Antenna switch 2 133 GPIO_18 / ANT_SW_1 Antenna switch 1 33 UART4 GPIO_17 / UART4_RX UART4 receive data 134 UART4 GPIO_16 / UART4_TX UART4 transmit data 34 GND GND Ground 135 GND GND Ground 35 GPIO GPIO_50 Configurable I/O GPIO_23 / ANT_SW_4 Antenna switch 4 136 36 GND GND Ground 137 GND GND Ground 37 MDM_RESOUT_N 138 GPIO_22 / ANT_SW_3 Antenna switch 3 _______________________________________________________________________________________________________________ Seite 11 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 38 UART1 GPIO_21 / UART1_RX UART1 receive data 139 UART1 UART1_TX UART2 transmit data 39 GND GND Ground 140 SPI GPIO_7 / SPI_CLK SPI clock 40 SPI GPIO_6 / SPI_CS_N SPI chip select 141 SPI GPIO_5 / SPI_MISO SPI master-in slave-out 41 SPI GPIO_4 / SPI_MOSI SPI master-out slave-in 142 SIM2 GPIO_2 / MDM_UIM2_RESET UIM2 reset 42 SIM2 GPIO_1 /MDM_UIM2_DETECT UIM2 detect (non dual voltage) 143 SIM2 GPIO_0 /MDM_UIM2_DATA UIM2 data 43 GND GND Ground 144 SIM2 VREG_L13_UIM2 Reference for UIM I/O pads 44 SIM2 GPIO_3 / MDM_UIM2_CLK UIM2 clock 145 GND GND Ground 45 GND GND Ground 146 GPIO GPIO_94 Configurable I/O 46 GPIO GPIO_80 Configurable I/O 147 GPIO GPIO_90 Configurable I/O 47 GPIO GPIO_82 Configurable I/O 148 GPIO GPIO_91 Configurable I/O 48 GPIO GPIO_87 Configurable I/O 149 GPIO GPIO_92 Configurable I/O 49 GPIO GPIO_88 Configurable I/O 150 GPIO GPIO_93 Configurable I/O 50 GPIO GPIO_89 Configurable I/O 151 I2C GPIO_85 / I2C_SCL I2C clock 51 I2C GPIO_84 / I2C_SDA I2C data 152 GND GND Ground 52 GND GND Ground 53 GND GND Ground 54 GND GND Ground 153 GND GND Ground 55 RF ANT_PTRX1 Primary cellular signal input/output 154 GND GND Ground 56 GND GND Ground 155 GND GND Ground 57 GND GND Ground 156 GND GND Ground 58 GND GND Ground _______________________________________________________________________________________________________________ Seite 12 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 157 GND GND Ground 59 MIPI GPIO_46 / RFFE4_DATA RF front end 4 interface data 158 GND GND Ground 60 GND GND Ground 159 GND GND Ground 61 MIPI GPIO_47 /RFFE4_CLK RF front end 4 interface clock 160 GND GND Ground 62 GND GND Ground 63 GND GND Ground 162 JTAG MDM_JTAG_TDI JTAG data input 64 GND GND Ground 163 JTAG MDM_JTAG_TDO JTAG data output 65 GND GND Ground 164 JTAG MDM_JTAG_TMS JTAG mode select input 66 GND GND Ground 165 JTAG MDM_JTAG_TRST_N JTAG reset 67 GND GND Ground 166 JTAG MDM_JTAG_TCK JTAG clock input 68 GND GND Ground 167 JTAG MDM_JTAG_SRST_N JTAG reset for debug 69 GND GND Ground 168 JTAG MDM_JTAG_PS_HOLD Power supply hold signal to PMIC 70 GND GND Ground 169 POWER VREG_L6_1P8 1.8V output 71 GND GND Ground 170 GND GND Ground 72 RF ANT_DRX1 Diversity cellular signal input/output 171 GND GND Ground 73 GND GND Ground 172 GND GND Ground 74 Reserved Reserved Reserved 173 GND GND Ground 75 GND GND Ground 174 GND GND Ground 76 GND GND Ground 175 GND GND Ground 77 GND GND Ground 176 GND GND Ground 78 RF ANT_GNSS GNSS signal input/output _______________________________________________________________________________________________________________ Seite 13 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 79 GND 80 GND Ground GPIO_38 / GRFC12 177 GND GND Ground 81 GPIO GPIO_69 Configurable I/O 178 GPIO_67 / EBI2_AD2/FBS_1 82 GND GND Ground 179 BOOT CONFIG GPIO_36 / FORCED_USB_BOOT Force USB boot control 83 GPIO GPIO_8 Configurable I/O 180 GPIO GPIO_83 Configurable I/O 84 GPIO GPIO_9 Configurable I/O 181 85 GPIO_59 / NC GND 182 86 Ground GPIO_24 / EBI2_AD1/FBS_0 GPIO 183 87 GND GPIO 184 GPIO_10 Configurable I/O MDM_MODE_0 TBD GPIO_11 Configurable I/O MDM_MODE_1 TBD 88 GND GND Ground 185 PCIE GPIO_65 / MDM_PCIE_WAKE_N PCIe host wake 89 Reserved Reserved Reserved 186 PCIE GPIO_61 / MDM_PCIE_RESET_N PCIe host reset 90 GND GND Ground 187 PCIE GPIO_64 / MDM_PCIE_CLKREQ_N PCIe clock request 91 GND GND Ground 188 WLAN IF WLAN_PWR_REQ 92 GND GND Ground 189 GPIO GPIO_60 Configurable I/O 93 WLAN IF WLAN_PWR_EN Enable WLAN Power 190 GPIO GPIO_68 Configurable I/O 94 WLAN IF WLAN_SLP_CLK 191 BT IF BT_RESET_N Enable Bluetooth PMD_RESIN_N Reset module GND Ground PON_1 Turn on module GPIO_95 / WLAN_EN Enable WLAN Power-reset 95 PMIC (active low) 192 96 193 GND Power-on PMIC (active high) WLAN IF 97 194 CBL_PWR_N WLAN IF GPIO_52 / COEX_UART_TX UART transmit data _______________________________________________________________________________________________________________ Seite 14 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 98 MPP PMIC_MPP_4 Multipurpose Pin 195 WLAN IF GPIO_53 / COEX_UART_RX UART receive data 99 MPP PMIC_MPP_2 Multipurpose Pin 196 MPP PMIC_MPP_6 Multipurpose Pin 100 GND GND_TO_VPH Ground 197 GND GND_TO_VPH Ground 101 POWER VPH_POWER External supply voltage 198 POWER VPH_POWER External supply voltage 102 POWER VPH_POWER External supply voltage 199 POWER VPH_POWER External supply voltage 103 POWER GND_TO_VPH Ground 200 GND GND Ground 104 HW_REV_RESISTOR Note: Pins should be grounded when not used in design. 2.10 Supply Voltage Absolute minimum/maximum supply voltages Nominal supply voltage Recommended supply voltage Voltage drop @ GSM power burst (33dBm) 3.9V ~ 4.1V 4V 4V <100mV During Hi RF Power GSM bursts the power amplifier can draw peak currents > 2Amps at VMAIN. The voltage drop during the GSM burst shall not exceed 100mV. 2.11 Power Consumption TA = +25°C, VPH_PWR =3.8V Voice Voice Voice Voice call call call call WCDMA WCDMA WCDMA WCDMA BC1 BC2 BC5 BC8 Voice call GSM850 Voice call GSM900 Voice call GSM1800 Voice call GSM1900 Output Power Output Power max. (typ. 23dBm) ~530mA ~570mA ~630mA ~580mA 0 dBm ~145mA ~145mA ~140mA ~140mA PCL 5 (typ. 32.5 dBm) ~260mA ~270mA PCL 0 (typ.30.5dBm) ~165mA ~165mA PCL 19 (typ. 5dBm) ~65mA ~65mA PCL 15 (typ.0dBm) ~65mA ~65mA _______________________________________________________________________________________________________________ Seite 15 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Output Power Standby current GSM Standby current WCDMA Standby current LTE DRX = 5 DRX = 7 DRX = 7 Output Power Tbd mA Tbd mA LTE data call B3 LTE data call B7 LTE data call B20 2.12 Environmental Specification 2.12.1 Temperature Range Range Operating temp. range Extended operating temp. range -25°C … +70°C -40°C … +85°C Storage temp. range -40°C … +85°C Note 1 3GPP spec. conform Operational Performance might slightly deviate from 3GPP spec. Note 1: Due to temperature specification of the chipset, the temperature of the power manager and the temperature of the modem chip shall not exceed +85°C. _______________________________________________________________________________________________________________ Seite 16 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 3 Evaluation Kit There are two types of evaluation boards fitted with the NAD V123x-0 modules: The IFB-1 board allows to power-supply the module directly with external 4V along with sense signals. This 4V power-supply should be able to deliver 3.5A max. The IFB-4 board type takes 12V as input voltage, down-converted to 4V by on-board circuitry. Features: USB 2.0 (micro USB) for USB to UART USB 3.0 (micro b) 2*SIM card slot Audio support with microphone and loudspeaker connectors JTAG connector for debug and programming 5 RF Antenna connector (PTRX,DRX,GNSS,WL,BT) 2* RS232 for UART 1 & 4 _______________________________________________________________________________________________________________ Seite 17 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe RF Connectors For Cellular RF measurements, use the PTRX and DRX antenna ports GNSS DRX PTRX Figure 1 Evaluation Kit for V123x-0. BT WLAN _______________________________________________________________________________________________________________ Seite 18 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe ON/OFF switch Only for 12 V supply 12 V DC Supply (Top Connector positive, bottom connector ground) Figure 2 Power supply for Evaluation Kit for V123x-0. SIM slot 1(bottom)/2(Up) Figure 3 SIM card and USB interfaces for Evaluation Kit for V123x-0. USB 3port Micro USB 2.0 USB to UART _______________________________________________________________________________________________________________ Seite 19 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 4 AT Command interface The modules supports standard AT command as listed below. Commands are compliant to 3GPP TS 27.007 and TS 27.005 Command Description AT+CMGF AT+CSCA AT+CMGS AT+CGMI AT+CGMM AT+CGMR AT+CGSN Message Format Service Centre Address Send Message Manufacturer Identification Request model identification Request revision identification Request product serial number Request international mobile subscriber identification Call mode AT+CIMI AT+CMOD AT+CHUP ATD ATA ATH AT+CBST AT+CEER AT+CVHU AT+CREG AT+COPS AT+CLCK AT+CPWD AT+CLIP AT+CLIR AT+CCWA AT+CHLD AT+CUSD AT+CLCC AT+CPOL AT+CPAS AT+CFUN AT+CPIN AT+CSQ AT+CMER AT+CSIM AT+CRSM AT+CMEE AT+CGDCONT AT+CGEQREQ AT-CGATT AT+CGACT AT+CGPADDR AT+CGSMS ATE Comment Only one Parameter is supported by the device. Hang up call Initiate a CS or PS call or supplementary service Answer incoming CS call command Hangup CS call command Select bearer service type Extended error report Voice hangup control Network registration PLMN selection Facility lock Change password Calling line identification presentation Calling line identification restriction Call waiting Call related supplementary services Unstructured supplementary service data List current calls Preferred PLMN list Phone active status Set phone functionality Enter PIN Signal quality Mobile termination event reporting Generic SIM access Restricted SIM access Report mobile termination error Define PDP context Request 3G quality of service profile PS attach or detach PDP context activate or deactivate Show PDP address Select service for MO SMS messages Character Echo ON/OFF _______________________________________________________________________________________________________________ Seite 20 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Command Description AT+CSMS AT+CSMP AT+CSDH AT+CSCB Check Message Service support Set Text Mode Parameters Show Text Mode Parameters Select Cell Broadcast Message Types Save Settings AT+CSAS AT+CRES AT+CMGL AT+CNMA AT+CMGC AT+CMMS AT+ATV AT+ATX AT+CNMI AT+CPMS AT+CMGW AT+CMSS AT+CMGD AT+CNUM AT+CPBS AT+CPBR AT+CPBW Comment Restore Settings Only one Parameter is supported by the device. Only one Parameter is supported by the device. List messages New message acknowledgement Send Command More Messages to Send DCE response format Result code selection and call progress monitoring control New Message Indications to TE Preferred Message Storage Write Message to Memory Send Message from Storage Delete Messages Get MSISDN Select phonebook memory storage Read phonebook entries Writephonebook entry _______________________________________________________________________________________________________________ Seite 21 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 5 Safety Recommendations according to EN60950-1 The V123x-0 devices must be supplied by a limited power source according to EN 60950-1. The clearance and creepage distances required by the end product must be withheld when the module is installed. The cooling of the end product shall not negatively be influenced by the installation of the module. _______________________________________________________________________________________________________________ Seite 22 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 6 RED/FCC/IC Regulatory Notices 6.1 Modifications WARNING: peiker acustic GmbH & Co. KG has not approved any changes or modifications to the V123x-0 device by the user. Any changes or modifications could void the user’s authority to operate the equipment. 6.2 Interference V1231-0 and V1233-0 devices comply with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) Those devices may not cause harmful interference, and (2) Those devices must accept any interference received, including interference that may cause undesired operation. V1231-0 is a Class b digital apparatus compliant with Canadian ICES-003. V1231-0 est un appareil numérique de la classe b conforme à la norme NMB-003 du Canada. V1231-0 est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. 6.3 FCC Class B Digital Device V1231-0 has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. _______________________________________________________________________________________________________________ Seite 23 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 6.3 OEM Responsibilities Antenna The systems antenna(s) must be installed such that 20 cm is maintained between the antenna(s) and the body of the user or nearby persons. The V123x-0 transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The preceding statement must be included as a Caution statement in OEM product manuals in order to alert users of FCC RF Exposure compliance. Maximum authorized antenna gain: refer to the MPE test reports Power Supply The power supply of the host device embedding a V123x-0 module must fulfill the following requirements: o Nominal supply voltage: 4V o Operating voltage range: 3.9V – 4.1V o The above operating voltage range MUST never, under any circumstances (including overshoot voltage and voltage drop), be exceeded. FCC Labeling Labeling requirements for a host device embedding V1231-0: V1231-0 is labeled with its own FCC ID Number. If the FCC ID is not visible when V12310 is installed inside another device, then the host device must contain the FCC ID number with the statement such as the following: "Contains Transmitter Module FCC ID: QWYV1231-0" or "Contains FCC ID: QWY-V1231-0" Labeling requirements for a host device embedding V1233-0: V1233-0 is labeled with its own FCC ID Number. If the FCC ID is not visible when V12330 is installed inside another device, then the host device must contain the FCC ID number with the statement such as the following: "Contains Transmitter Module FCC ID: QWYV1233-0" or "Contains FCC ID: QWY-V1233-0" IC Labeling Labeling requirements for a host device embedding V1231-0: V1231-0 is labeled with its own IC ID Number. If the IC ID is not visible when V1231-0 is installed inside another device, then the host device must contain the IC ID number with the statement such as the following: "Contains Transmitter Module IC 6588A- V12310" or "Contains IC 6588A- V12310". _______________________________________________________________________________________________________________ Seite 24 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 7 List of Acronyms 3GPP ADC ADN A-GPS CP AMR AT AWS BER CLIP CLIR CSD DARP EDGE DTMF FCC FDN FTP GCF GSM GPIO GPRS GPS HSPA HW IC LED LTE MO MT OEM PCB PCM PDU PIN PTCRB RF RoHs UART USB USIM UMTS WCDMA 3 rd Generation Partnership Project Analog Digital Converter Abbreviated Dialing Number Assisted GPS Control Plane Adaptive Multi Rate Attention Command Advanced Wireless Services Bit Error Rate Calling Line Identification Presentation Calling Line Identification Restriction Circuit Switch Data Downlink Advanced Receiver Performance Enhanced Data rates for GSM Evolution Dual Tone Multi Frequency Federal Communications Commission Fixed Dialing Number File Transfer Protocol Global Certification Forum Global System for Mobile communication General Purpose Input Output General Packet Radio Service Global Positioning System High Speed Uplink Packet Access Hardware Industry Canada Led Emitting Diode Long-Term Evolution Mobile Originated Mobile Terminated Original Equipment Manufacturer Printed Circuit Board Pulse Code Modulation Protocol Data Unit Personal Identification Number PCS Type Certification Review Board Radio Frequency Restriction of Hazardous Substances Universal Asynchronous Receiver and Transmitter Universal Serial Bus Universal Subscriber Identity Module Universal Mobile Telecommunications System Wideband Code Division Multiple Access _______________________________________________________________________________________________________________ Seite 25 peiker acustic GmbH & Co. KG, Max-Planck-Straße 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschäftsführung: Andreas Peiker, Geschäftsführer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 25 Language : en-US Tagged PDF : Yes Author : PEIKER acustic Creator : Microsoft® Office Word 2007 Create Date : 2017:09:04 17:21:58+02:00 Modify Date : 2017:09:04 17:21:58+02:00 Producer : Microsoft® Office Word 2007EXIF Metadata provided by EXIF.tools