Pelco Ccc1390H Series Camera C2924M 4 05 Users Manual

C2924M (405) to the manual 0c58c403-41d0-41cc-84aa-cbd75f03e894

2015-02-02

: Pelco Pelco-Ccc1390H-Series-Camera-C2924M-4-05-Users-Manual-440396 pelco-ccc1390h-series-camera-c2924m-4-05-users-manual-440396 pelco pdf

Open the PDF directly: View PDF .
Page Count: 44

Contents
List of Illustrations
Warnings

INSTALLATION/OPERATION

CCC1390H Series

Camera

C2924M (4/05)

 
C2924M (4/05) 3
 
Contents
 
Regulatory Notices  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6
Description  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Product Features   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Models  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Parts List   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Optional Accessories  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Required Tools  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Lens Mounting   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Wiring an Auto Iris Lens   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Mounting the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Camera Mounting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Connecting Power, Video, and Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Connecting Power  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Connecting AC Power  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Connecting DC Power  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Connecting Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Connecting External Control   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Connecting Serial Control (Pelco D/Pelco P)   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Connecting Day/Night Filter Control   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Accessing Setup Menus  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Navigating Setup Menus from the Rear Panel  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Navigating Setup Menus from a Pelco Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Using Preset 95 to Access Setup Menus  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Navigating Setup Menus  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Setup Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Main Menu   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Profiles  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Active   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Save As  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Exposure Settings   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Auto Exposure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Video Level  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Flickerless  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Shutter Speed  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Automatic Gain Control (AGC)   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Digital Slow Shutter (DSS (SENS))  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Day and Night  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Day and Night Detection   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Day and Night Filter Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Function Settings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Line Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
White Balance   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Manual Red/Blue  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Gamma  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Sharpness  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
E-Zoom   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Masking   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Title  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Camera Setup   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Auto Iris Lens Adjustment  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

 
4 C2924M (4/05)
 
Pixel Correction  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
System Information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Lens Focusing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Camera Synchronization  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Manual White Balance Calibration   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Specifications  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

 
C2924M (4/05) 5
 
List of Illustrations
 
1   CCC1390H Series Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2   DC-Drive Auto Iris Lens Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
3   Mounting Lens to Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4   Connecting AC Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
5   Connecting DC Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
6   Installing the External Control Connector  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
7   Conﬁguring a Serial Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
8   Day/Night Filter Control Conﬁguration  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
9   Quick Setup Indicators and Presses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
10   Rear Panel Indicators and Presses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
11   Sample Proﬁle Scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
12   Lens Focus  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
 
List of Tables
 
A   Recommended Wire Gauge and Maximum Wiring Distances  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
B   Video Coaxial Cable Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
C   Camera/Controller Settings for KBD200A/KBD300A (Direct Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
D   Day/Night Control Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
E   Rear Panel Buttons and Actions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
F   Pelco Controller Buttons and Actions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
G   Settings by Profile  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

6 C2924M (4/05)

Regulatory Notices

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RADIO AND TELEVISION INTERFERENCE

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and the receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

You may also ﬁnd helpful the following booklet, prepared by the FCC: “How to Identify and Resolve Radio-TV Interference Problems.” This booklet

is available from the U.S. Government Printing Ofﬁce, Washington D.C. 20402.

Changes and Modiﬁcations not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this

equipment under Federal Communications Commission’s rules.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Warnings

To avoid damaging your camera, please note the following:

1. The camera has threaded mounting locations on the top and bottom of the case. Use only a standard photographic mounting bolt with a

1/4-20 UNC thread.

2. Do not touch the surface of the optical ﬁlter. If the ﬁlter is dusty or is accidentally touched, use clean, compressed air or lens cleaning paper

to clean it.

3. Do not expose the camera imager to direct sunlight as this may impair camera performance. Always keep the lens mount cap in place until

you install the lens.

4. Do not use this camera outdoors without an appropriate enclosure. Do not install near ﬂammable gas or corrosive chemical fumes.

5. Use a soft dry cloth to clean the camera case. If necessary, use a soft cloth moistened with a neutral detergent diluted with water; then dry

with the dry cloth. Never use alcohol, benzene, or other volatile solutions.

C2924M (4/05) 7

Description

The CCC1390H Series camera is a compact, wide dynamic range (WDR), day/night camera. Its WDR technology provides up to 60 dB of dynamic

range and produces superior images over a wide range of lighting conditions, including extreme backlight conditions. The camera also uses a

removable infrared (IR) cut ﬁlter to switch between color and black-white (B-W) modes as environmental lighting conditions change. It also pro-

vides a dual resolution of 530 TVL (B-W) and 480 TVL (color).

On-screen programmable menus can be accessed locally using the rear panel button or remotely using any Pelco controller with Pelco P or Pelco D

protocol. Use these menus to select a speciﬁc proﬁle or to customize and save camera settings for the speciﬁc application.

The CCC1390H Series camera has a standard CS-mount and can be used with ﬁxed, manual, or DC-drive auto iris lenses. The auto iris is controlled

through a standard four-pin square connector that is included with all Pelco auto iris lenses.

The CCC1390H Series camera is quick and easy to install and is ideal for Pelco’s DomePak

and ImagePak

ﬁxed camera dome/enclosure

packages.

PRODUCT FEATURES

•

Compact Body Style

•

Wide Dynamic Range (60 dB Maximum); Captures Both High-Luminance and Low-Luminance Objects

•

Day/Night with Automatic or Manual Control; Captures High-Quality Color During the Day and Clear B-W Images at Night

•

Electronic Zoom

•

1/3-Inch Format Sony

SS-2WD CCD Imager

•

Digital Signal Processing

•

530 TV Lines (B-W); 480 TV Lines (Color)

•

On-Screen Menu Conﬁguration

•

Four Preset Application Proﬁles; One User-Deﬁnable Proﬁle

•

Selectable Auto White Balance (AWB), Automatic Gain Control (AGC), Electronic Shutter Control (ESC), and Backlight Compensation (BLC)

•

Digital Slow Shutter (DSS)

•

Flickerless Mode

•

CS Lens Mount (C-Mount Lens Requires Optional Adapter)

•

Autosensing DC-Drive Auto Iris

•

Autosensing 24 VAC/12 VDC with Line Lock or Internal Synchronization

•

Internal Top/Bottom Mount

8 C2924M (4/05)

Figure 1.

CCC1390H Series Camera

MODELS

CCC1390H-6 1/3-inch high resolution day/night, WDR, CCD camera, 24 VAC or 12 VDC, NTSC format

CCC1390H-6X 1/3-inch high resolution day/night, WDR, CCD camera, 24 VAC or 12 VDC, PAL format

 

 







Lens Mount: Mount a standard CS-mount lens to the CCC1390H Series camera (refer to Lens Mounting). To use a C-mount lens, install a

C/CS-mount adapter.

Back Focus Locking Screw: Use a 1.5-mm Allen wrench to adjust the back focus (refer to Lens Focusing).

Camera Mount and 3a Mount Adapter: Use the top or bottom mount hole. The maximum thread depth (top) is 0.188 inches (4.7 mm); the

adapter extends the thread depth (top) to 0.25 inches (6.4 mm). The maximum thread depth (bottom) is 0.25 inches (6.4 mm). Refer to Camera

Mounting.

Serial Terminating Switch: Use this switch to terminate the serial signal at the last camera on the serial chain (refer to Connecting

External Control).

Auto Iris Lens Connector: Insert the four-pin connector from the DC-drive auto iris lens into this connector (refer to Lens Mounting).

Video Output Connector: Connect a coaxial video cable to this BNC connector to output the video image (refer to Connecting Video).

Setup Button: Use this ﬁve-position button to conﬁgure the camera either directly (refer to Quick Setup) or through the setup menus (refer

to Accessing Setup Menus).

Power Terminal Strip: Use this three-pin, push-in type terminal strip to connect either 12 VDC or 24 VAC power (refer to Connecting

Power).

Indicators: Use these indicators to quickly determine camera status (refer to Quick Setup).

 External Control Connector: Use this seven-pin connector to connect the camera to one or more serial devices. Use it also to connect an

external day/night ﬁlter switch. Refer to Connecting External Control for more information.

C2924M (4/05) 9

PARTS LIST

CCC1390H Series camera

Quick Start Guide

Safety Instructions

External control connector assembly: seven-pin micro (1.25 mm) connector with wires (26 AWG) and connector cover

Camera mount spacer

Four-pin auto iris connector (type DN-152N)

Lens mount cap

Resource CD:

•

Installation/Operation manual: INSTALL.PDF

•

Quick Start Guide: QSG.PDF

•

Important Safety Instructions: SAFETY.PDF

OPTIONAL ACCESSORIES

PCMA40 Lens adapter. Adapts standard C-mount lenses to CS-mount cameras.

REQUIRED TOOLS

Small Phillips screwdriver for connector cover

Small ﬂat tip screwdriver for serial termination

Allen wrench (1.5 mm) for back focus adjustment

Neutral density ﬁlter (ND3) for auto iris adjustment

10 C2924M (4/05)

Lens Mounting

The CCC1390H Series camera supports both manual and DC-drive auto iris lenses, either ﬁxed focal length or varifocal. It automatically senses an

auto iris lens as soon as you plug in the connector. The camera has a standard CS-mount that can accept a C-mount lens with a PCMA40 lens

adapter.

After mounting an auto iris lens, but before using the camera, perform the auto iris automatic adjustment procedure (refer to

Auto Iris Lens

Adjustment)

. Also perform this procedure each time you change the lens.

NOTE:

The CCC1390H Series camera does not support video-drive auto iris lenses.

WIRING AN AUTO IRIS LENS

DC-drive auto iris lenses are controlled through the four-pin drive connector (type D4-152N). Figure 2 identiﬁes the pin connections for the auto iris

lens connector on the back of the camera.

Figure 2.

DC-Drive Auto Iris Lens Connector

Pin DC-Drive Auto Iris Lens

1 Control coil negative (–)

2 Control coil positive (+)

3 Drive coil positive (+)

4 Drive coil negative (–)

C2924M (4/05) 11

MOUNTING THE LENS

To mount the lens onto the camera (refer to Figure 3):

1. Make sure the lens will not touch the camera imager when installed.

2. Use clean, compressed air or a clean, dry lens cloth to make sure there is no dust or other foreign matter between the lens and the camera

imager.

C-mount lens:

Screw the adapter onto the lens.

4. Screw the lens onto the lens mount.

DC-drive auto iris lens:

Connect the four-pin connector from the lens to the connector on the back of the camera.

Figure 3.

Mounting Lens to Camera

CS-MOUNT

LENS

AUTO IRIS

LENS CABLE

AND CONNECTOR

(OPTIONAL)

C/CS MOUNT ADAPTER

(FOR C-MOUNT LENS ONLY)

12 C2924M (4/05)

Camera Mounting

The CCC1390H Series camera can be mounted from either the top or bottom, depending on the type of camera mount used in your installation. Use

a standard 1/4-20 screw. The maximum thread depth (top) is 0.188 inches (4.7 mm). To extend the thread depth (top) to 0.25 inches (6.4 mm), use

the camera mount spacer (supplied). The maximum thread depth (bottom) is 0.25 inches (6.4 mm).

The CCC1390H Series camera can be ﬁtted with most Pelco lenses and mounted into most Pelco domes and enclosures, resulting in the greatest

possible number of combinations. This means you can ﬁnd a solution for nearly any application.

When selecting a lens, dome, or enclosure for this camera, consider how the physical dimensions of each component may affect camera

installation and operation. Speciﬁcally, you should address the following three issues.

•

Enclosure size:

The camera dimensions are 2.2 (D) x 2.09 (W) x 2.17 (H) inches (5.6 x 5.3 x 5.5 cm). Make sure the enclosure is large

enough for both the camera and the lens.

•

Lens size:

Some lenses have minimum and maximum lengths. To focus the scene correctly, you may have to adjust the lens to its maximum

length. This could affect how it ﬁts within the enclosure.

•

Optical alignment:

The optical center of this camera may be too low for some enclosures. As a result, the lower portion of the scene may

be obstructed by the enclosure itself. The camera sled in many Pelco enclosures has a low side and a high side. You may be able to raise

the optical center by ﬂipping the camera sled to the high side.

NOTE:

To simplify lens and enclosure selection, Pelco offers ImagePak options for the CCC1390H Series camera. Select the lens and the dome or

enclosure. Pelco will build and test it for you. Contact Pelco or your dealer for more information.

C2924M (4/05) 13

Connecting Power, Video, and Control

The CCC1390H Series camera offers standard power and coax video connectors as well as an external control connector. Before installation,

identify how you will connect each power, video, and control lead to the camera.

CONNECTING POWER

The CCC1390H Series camera is designed to operate from either a 12 VDC or a 24 VAC power source. The camera automatically senses power

type. Use only a Class 2 isolated power source that can supply 12 VDC ±15% or 24 VAC ±15%, 50/60 Hz. Maximum power consumption is about

3.5 watts.

NOTES:

•

Be sure to use 60 Hz power for NTSC (CCC1390H-6) and 50 Hz power for PAL (CCC1390H-6X).

•

Install the camera near a socket or outlet that is easily accessible.

Use Table A to help you identify the necessary wire gauge and maximum cable distance. This table applies to two-conductor copper wire.

These maximum distances are based on a maximum allowable voltage drop of 10%.

WARNINGS:

•

Do not connect high voltage power to the camera because you may damage the camera.

•

Do not short circuit the power leads when connecting the power supply to the camera.

•

Do not remove the connector cover during camera operation.

Table A.

Recommended Wire Gauge and Maximum Wiring Distances

Wire Gauge Maximum Distance

12 VDC 24 VAC

24 AWG (0.25 mm

) 373 ft (113 m) 224 ft (68 m)

22 AWG (0.35 mm

) 594 ft (181 m) 356 ft (108 m)

20 AWG (0.5 mm

) 945 ft (288 m) 567 ft (172 m)

18 AWG (1.0 mm

) 1,504 ft (458 m) 902 ft (372 m)

16 AWG (1.5 mm

) 2,388 ft (727 m) 1,432 ft (436 m)

14 AWG (2.5 mm

) 3,809 ft (1,160 m) 2,285 ft (696 m)

12 AWG (4.0 mm

) 6,037 ft (1,840 m) 3,622 ft (1,103 m)

10 AWG (6.0 mm

) 9,600 ft (2,926 m) 5,760 ft (1,755 m)

14 C2924M (4/05)

CONNECTING AC POWER

The CCC1390H Series camera requires a power supply of 24 VAC ±15% (20.4 to 27.6 VAC), 50/60Hz. Make sure the power supply has a minimum

rating of 270 mA.

When connecting more than one camera to the same AC transformer, remember the following:

•

Connect the same side of the transformer to the same terminal on all cameras. Otherwise, the cameras may be out of phase, causing a

vertical roll when switching between cameras. Refer to

Camera Synchronization

for more information.

•

Use a transformer whose rated power supply is greater than 270 mA multiplied by the number of cameras.

To connect AC power:

1. Strip at least 0.4 inches (10 mm) of the insulation from each power wire.

2. Press and hold the button over either hole marked 24 VAC.

3. Insert one wire from the power supply into the hole and release the button.

4. Gently pull the wire to make sure it is secure.

5. Repeat steps 2 through 4 for the second wire from the power supply.

6. If you are using a ground wire, repeat steps 2 through 4, inserting the ground wire into the hole marked GND.

Figure 4.

Connecting AC Power

POWER SUPPLY

INPUT

24 VAC

OUTPUT

BUTTONS

C2924M (4/05) 15

CONNECTING DC POWER

The CCC1390H Series camera requires a power supply of 12 VDC ±15% (10.2 to 13.8 VDC). Make sure the power supply has a minimum rating of

390 mA.

To connect DC power:

1. Strip at least 0.4 inches (10 mm) of the insulation from each power wire.

2. Press and hold the button over the hole marked (–).

3. Insert the negative wire from the power supply into the hole and release the button.

4. Gently pull the wire to make sure it is secure.

5. Repeat steps 2 through 4 for the positive wire from the power supply. Use the hole marked (+). For safety, add a 1.0 A slow blow fuse to the

positive wire from the power supply. The fuse should be less than 4 inches (10 cm) from the positive terminal on the power supply.

Figure 5.

Connecting DC Power

CONNECTING VIDEO

Connect a coaxial video cable to the BNC connector on the back of the camera. Refer to Table B for the type of video coaxial cable to use.

*Cable requirements:

75 ohms impedance

All-copper center conductor; steel-center conductor cable may result in poor performance

All-copper braided shield with 95% braid coverage

If white spots appear in the video image, one or more pixels on the camera imager may be defective. This condition is common to CCD camera

imagers. To correct this condition, refer to

Pixel Correction

WARNINGS:

•For safety, include a 1.0 A slow blow fuse when connecting DC power, as shown in Figure 5.

•The DC power supply must be UL- and CE-certiﬁed.

•Make sure you wire the power polarity correctly.

Table B. Video Coaxial Cable Requirements

Cable Type* Maximum Distance

RG59/U 750 ft (229 m)

RG6/U 1,000 ft (305 m)

RG11/U 1,500 ft (457 m)

+12

VDC

GND

4 INCH (10 CM) MAX.

1.0 A FUSE

(SLOW BLOW)

POWER

SUPPLY

INPUT

BUTTONS

16 C2924M (4/05)

CONNECTING EXTERNAL CONTROL

The external control connector on the rear panel lets you remotely access and control the CCC1390H Series camera. The external control

connector assembly is a seven-pin micro (1.25 mm) connector with wires (26 AWG) and connector cover.

You can access and conﬁgure the menu settings from any Pelco keyboard, receiver, or other device that supports the Pelco D or Pelco P protocol.

The camera supports the following settings:

•Baud rate: 2400, 4800, 9600, 19200

•Start bit: 1

•Data bits: 8

•Stop bit: 1

•Parity: None

You can also control day/night ﬁlter operation from an external switch.

Figure 6 identiﬁes the pin connections for the enclosed external control connector assembly. It also identiﬁes pins 1 and 7.

Figure 6. Installing the External Control Connector

TO CONTROL

DEVICE

GND

RX+

RX-

REMOVE

CONNECTOR

COVER

INSTALL

CONNECTOR

COVER

PIN 7

PIN 1

Pin Lead Color

1 Pelco Data RX+ Red

2 Pelco Data RX– White

3 Ground Black

4 Pelco Data TX+ Red

5 Pelco Data TX– White

6 Ground Black

7 Day/Night Control Signal Input Brown

C2924M (4/05) 17

CONNECTING SERIAL CONTROL (PELCO D/PELCO P)

To connect serial control to the camera (refer to Figure 7):

1. Turn off power to the camera.

2. If necessary, use a small Phillips screwdriver to remove the connector cover from the rear panel (refer to Figure 6).

3. If necessary, plug the external control connector assembly (supplied) into the camera. Then use a small Phillips screwdriver to secure the

assembly connector cover to the rear panel.

4. Use 100-ohm twisted pair cabling to wire each pair on the enclosed connector assembly. The decision to use shielded cable depends on

your installation; shielded cable may be optional.

Figure 7. Conﬁguring a Serial Chain

5. Wire the camera to the control device as follows:

•Pin 1 (red, RX+) to the TX+ lead on the control device.

•Pin 2 (white, RX–) to the TX– lead on the control device.

•Pin 3 (black, ground) to the ground lead on the control device.

•Shielded cable only: Connect the shield to either pin 3 (black, ground) or pin 6 (black, ground).

6. To connect additional cameras in a serial chain:

a. Use a small ﬂat tip screwdriver to turn the termination switch on this camera to OFF. The default position is ON.

b. Wire this camera to the next camera as follows:

•Pin 4 (red, TX+) to pin 1 (red, RX+) on the next camera.

•Pin 5 (white, TX–) to pin 2 (white, RX–) on the next camera.

•Pin 6 (black, ground) to pin 3 (black, ground) on the next camera.

•Shielded cable only: Connect the shield to either pin 3 (black, ground) or pin 6 (black, ground).

TERM = OFF TERM = OFF

TERM = ON

GND (6) TO (3)

TX- (5) TO RX- (2)

TX+ (4) TO RX+ (1)

GND (6) TO (3)

TX- (5) TO RX- (2)

TX+ (4) TO RX+ (1)

PIN 7

PIN 1

RX+ (1)

RX- (2)

GND (3)

PIN 7

PIN 1

PIN 1 PIN 7

18 C2924M (4/05)

7. If you are not connecting additional cameras, or after adding all cameras to the chain, make sure you set the termination switch to ON for

the last camera in the chain.

8. Access the CAMERA SETUP menu to set the following (refer to Camera Setup):

•Set a unique ADDRESS for each camera on the serial chain.

•Set the communication rate (COM SPEED) to match the rate of each camera on the serial chain.

Table C lists the ADDRESS and COM SPEED by Pelco protocol for accessing the camera from a Pelco KBD200A or KBD300A.

*To select the camera using the Pelco P protocol, add one to the camera number at the controller. For example, if the ADDRESS at the camera is

set to 10, select camera 11 at the controller.

CONNECTING DAY/NIGHT FILTER CONTROL

In some installations, high infrared (IR) illumination or other light sources may interfere with the camera’s automatic day/night mode operation.

Use an external day/night ﬁlter switch, such as a photosensor, to keep the camera from constantly switching ﬁlters.

The control signal input responds as shown in Table D:

NOTES:

•Do not exceed these values.

•The CCC1390H Series camera responds only to the input signal from the switch. It does not provide enough power to drive an external

device.

To connect an external day/night ﬁlter switch to the camera (refer to Figure 8):

1. Turn off power to the camera.

2. If necessary, use a small Phillips screwdriver to remove the connector cover from the rear panel (refer to Figure 6).

3. If necessary, plug the external control connector assembly (supplied) into the camera. Then use a small Phillips screwdriver to secure the

assembly cover to the rear panel.

Table C. Camera/Controller Settings for KBD200A/KBD300A (Direct Mode)

Equipment Parameter PELCO D PELCO P

Camera ADDRESS 1-30 1-30

COM SPEED 2400 4800

Keyboard ADDRESS 1-30 2-31*

DIP SWITCH ON: 5, 7

OFF: all others

ON: 5

OFF: all others

Table D. Day/Night Control Signal

Signal Voltage D/N Mode

Open or High 3.0V to 3.3V AUTO

Short or Low -0.3V to 0.3V BW

C2924M (4/05) 19

4. Use 100-ohm twisted pair cabling to wire the device to the enclosed connector assembly. The decision to use shielded cable depends on

your installation; shielded cable may be optional.

Figure 8. Day/Night Filter Control Conﬁguration

5. Wire the camera to the external switch as follows:

•Pin 7 (brown, signal input) to the (+) lead on the external switch.

•Pin 6 (black, ground) to the (–) lead on the external switch.

•Shielded cable only: Connect the shield to either pin 3 (black, ground) or pin 6 (black, ground).

6. Change DAY & NIGHT to EXT. (external) on the EXPOSURE SETTINGS menu.

7. Conﬁgure the external switch as follows:

•Open or High: Camera operates in AUTO mode.

•Short or Low: Camera operates in BW mode.

INPUT (7)

GND (6)

EXTERNAL SWITCH

PIN 7

PIN 1

20 C2924M (4/05)

Quick Setup

Several CCC1390H Series camera settings can be changed directly from the rear panel button. When a rear panel indicator is lit, the correspond-

ing option is enabled. You can change the following options directly from the rear panel:

AGC Press the button up to enable or disable automatic gain control (AGC). Refer to Automatic Gain Control (AGC) for more

information.

D/N Press the button left to enable or disable day and night mode. When enabled, the AUTO mode is selected. When disabled, the

COLOR mode is selected. Refer to Day and Night for more information.

You cannot change day and night mode when AGC is disabled; the camera uses the COLOR mode.

SENS Press the button down to enable or disable DSS (SENS). Refer to Digital Slow Shutter (DSS (SENS)) for more information.

If you disable SENS on the rear panel, the camera saves the DSS (SENS) value on the EXPOSURE SETTING menu.

WD Press the button right to change the auto exposure mode. When this indicator is lit, WDR is selected. Otherwise, the NORMAL

auto exposure mode is selected. Refer to Auto Exposure for more information.

NOTES:

•To enable the rear panel indicators, the LED setting on the CAMERA SETUP menu must be set to ON (the default).

•To enable the quick setup feature, the SWITCH setting on the CAMERA SETUP menu must be set to ON (the default).

Figure 9 shows the rear panel indicators and their corresponding button presses.

Figure 9. Quick Setup Indicators and Presses

AGC

SENS

D/N

C2924M (4/05) 21

Accessing Setup Menus

NAVIGATING SETUP MENUS FROM THE REAR PANEL

You can use the ﬁve-position button on the rear panel to access and navigate the setup menus (refer to Figure 10).

Figure 10. Rear Panel Indicators and Presses

Table E lists the button presses for each menu action.

To display a menu:

1. Press and hold the button for two seconds to open the MAIN MENU. The four indicators on the rear panel blink until you close the setup

menu.

2. Press the button up or down to select a menu.

3. Press the center of the button to open the menu.

To change a setting:

1. Press the button up or down to select the item.

2. Press the center of the button to open the item.

3. Press the button up or down to move through the options.

4. Press the center of the button to save the setting and return to the menu.

To move to a previous menu, select BACK and press the center of the button.

To close the setup menus, select EXIT from any menu and press the center of the button.

NOTES:

•When you select BACK or EXIT on any menu, the camera saves the current settings into memory.

•The menu closes automatically after three minutes of inactivity.

Table E. Rear Panel Buttons and Actions

MENU ACTION BUTTON ACTION

Enter setup menus. Long center press

Move up or down in menu or item options. Up or down press

Move right or left in menu. Right or left press

Select menu or item. Short center press

Save setting and exit to menu. Short center press

RIGHT

DOWN

LEFT

SELECT

22 C2924M (4/05)

NAVIGATING SETUP MENUS FROM A PELCO CONTROLLER

USING PRESET 95 TO ACCESS SETUP MENUS

You can use preset 95 to access and navigate the setup menus from various Pelco controllers. Use the instructions for your controller to access

the main menu.

CM6700/CM6800

1. Enter the camera number and press the CAM key.

2. Enter 95 and hold the PRESET key for two seconds. A menu screen appears.

3. Move the joystick down to highlight SET.

4. Move the joystick right. The MAIN MENU appears.

KBD200A/KBD300A (Direct Mode)

1. Enter the camera number and press the CAM key.

2. Enter 95.

3. Press the PRESET key. The MAIN MENU appears.

CM9500

1. Enter the camera number and press the CAM key. The Main menu appears.

2. Highlight SETUP in the Main menu and press the SELECT key.

3. Highlight CAM in the Setup menu and press the SELECT key.

4. Highlight PRESET in the Camera menu and press the SELECT key.

5. Enter 95 and press the F1 key. The MAIN MENU appears.

CM9740/CM9760/CM9770/CM9780

1. Press the ESCAPE key to open the Main menu. Select DEF. The Deﬁne Submenu appears.

2. Enter your four-digit PIN if this is your ﬁrst time entering this mode.

3. Enter 95 and select PRST. The MAIN MENU appears on the monitor.

4. Select the Quit icon to return to the default menu.

MPT9500 (RS-485 Mode)

1. Enter 95 and press the PRESET SET key.

2. Press the F2 key. The MAIN MENU appears.

PelcoNet™

1. Check the Set box.

2. Click the preset 95 button. The MAIN MENU appears.

C2924M (4/05) 23

NAVIGATING SETUP MENUS

As soon as you access the MAIN MENU, the four indicators on the rear panel blink until you close the setup menu. Table F lists the buttons and

actions for menu navigation.

NOTE: If your Pelco controller does not have a joystick, use the up, down, right, and left buttons.

To display a menu:

1. Use the joystick to select a menu.

2. Press the iris open button to open the menu.

To change a setting:

1. Use the joystick to select the item.

2. Press the iris open button to open the item.

3. Move the joystick up or down to move through the options.

4. Press the iris open button to save the setting and return to the menu.

To move to a previous menu, select BACK and press the iris open button.

To close the setup menus, select EXIT from any menu and press the iris open button.

NOTES:

•When you select BACK or EXIT on any menu, the camera saves the current settings into memory.

•The menu closes automatically after three minutes of inactivity.

•The rest of this document describes navigating the menus from the rear panel button. Refer to Table F for the equivalent Pelco controller

commands.

Table F. Pelco Controller Buttons and Actions

MENU ACTION BUTTON ACTION

Move up or down in menu or item options. Move joystick up or down.

Move right or left in menu. Move joystick right or left.

Select menu or item. Press the iris open button.

Save setting and exit to menu. Press the iris open button.

24 C2924M (4/05)

Setup Menus

The CCC1390H Series camera uses setup menus instead of hardware switches for conﬁguring the camera. As a result, you have more options for

customizing the camera for its speciﬁc application.

NOTES:

•After you customize any aspect of the CCC1390H Series camera, be sure to save your custom settings. (Refer to Proﬁles for information

about saving custom settings.)

•Menu items that cannot be changed are either disabled or marked with an asterisk (*).

•FLICKERLESS changes to SHUTTER SPEED when AUTO EXPOSURE mode is set to MANUAL.

The setup menu tree is represented on this and the next page:

MAIN MENU

PROFILES >

EXPOSURE SETTINGS >

FUNCTION SETTINGS >

CAMERA SETUP >

AI AUTO ADJUSTMENT >

PIXEL CORRECTION >

SYSTEM INFORMATION >

EXIT

PROFILES

ACTIVE > STANDARD

SAVE AS > CUSTOM

*DEFAULT STANDARD

BACK EXIT

EXPOSURE SETTINGS

AUTO EXPOSURE > NORMAL

VIDEO LEVEL > 0

FLICKERLESS > OFF

AGC > ON

DSS(SENS) > 4

DAY & NIGHT > COLOR

D&N DETECTION >

D&N FILTER LIMIT >

BACK EXIT

FUNCTION SETTINGS

LINE SYNC >

WHITE BALANCE > AUTO

MANUAL RED/BLUE >

GAMMA > 60%(NORM)

SHARPNESS >

E-ZOOM >

MASKING >

TITLE >

BACK EXIT

AI AUTO ADJUSTMENT

OK CANCEL

PIXEL CORRECTION

COVER THE LENS

AND SELECT OK

OK CANCEL

SYSTEM INFORMATION

FIRMWARE VERSION 1.0

OSD VERSION 1.0

RESTORE FACTORY SETTINGS >

BACK EXIT

RESTORE FACTORY SETTINGS

OK CANCEL

CAMERA SETUP

ADDRESS > 1

COM SPEED > 4800

LED > ON

SWITCH > ON

BACK EXIT

C2924M (4/05) 25

LINE SYNC

LINE SYNC > AUTO

V-PHASE ADJ >

BACK EXIT

V-PHASE ADJ

PHASE VALUE = 45

MANUAL RED/BLUE

RED GAIN > -1

BLUE GAIN > -2

RED HUE > 1

BLUE HUE > 1

BACK EXIT

SHARPNESS

APERTURE GAIN > -1

BACK EXIT

E-ZOOM

ZOOM > OFF

POSITION >

BACK EXIT

POSITION

MASKING

MASK > OFF

MASK EDIT >

MASK ERASE

BACK EXIT

MASK SETTING

TITLE

TITLE > OFF

EDIT TITLE >

BACK EXIT

EDIT TITLE

ABCDEFGHIJKLM

NOPQRSTUVWXYZ

abcdefghijklm

nopqrstuvwxyz

0123456789-/

BACK BS

_________________

26 C2924M (4/05)

MAIN MENU

The following sections describe each menu and all settings associated with that menu.

The sample screens in each section show the default settings.

To display the MAIN MENU:

•Press and hold the center of the button on the rear panel. Refer to Navigating Setup

Menus from the Rear Panel.

•Use the Pelco controller. Refer to Navigating Setup Menus from a Pelco Controller.

Proﬁles

Select this option to access the camera proﬁle settings (refer to Proﬁles).

Exposure Settings

Select this option to conﬁgure the exposure settings (refer to Exposure Settings).

Function Settings

Select this option to conﬁgure the function settings (refer to Function Settings).

Camera Setup

Select this option to conﬁgure the communication settings for the camera (refer to Camera Setup).

AI Auto Adjustment

Select this option to perform the auto iris lens automatic adjustment procedure (refer to Auto Iris Lens Adjustment).

Pixel Correction

Select this option to perform the automatic pixel correction procedure (refer to Pixel Correction).

System Information

Select this option to display the camera ﬁrmware information or to restore the factory default settings (refer to System Information).

PROFILES

Use this option to select a proﬁle or save custom settings. Use proﬁles for faster installation or to

adjust camera settings quickly for changing light conditions. The default is STANDARD.

The CCC1390H Series camera offers four predeﬁned proﬁles and one custom, or user-deﬁnable,

proﬁle. You cannot modify predeﬁned proﬁles.

ACTIVE

Select one of the following application proﬁles:

STANDARD Select this proﬁle for most scenes. This is the default.

DAY&NIGHT Select this proﬁle if the camera is located outside a building or in certain indoor low-light applications. When selected, the

camera adjusts its settings to account for light level changes. Examples include parking lots and walkways.

WDR Select this proﬁle if light from an exterior window or door in the camera view causes an object or person to be backlit or

silhouetted.

GAMING Select this proﬁle if the camera scene is illuminated by mixed interior lighting and includes self-illuminated devices. Examples

include arcades with gaming machines with bright, ﬂashing lights.

CUSTOM Select this proﬁle to activate your saved camera settings.

<HOLD> Whenever you open the setup menus, the current camera settings are copied into the <HOLD> proﬁle. As you change camera

settings, the camera stores these new settings into this proﬁle. This lets you experiment with new settings without erasing the

CUSTOM proﬁle. When you perform a SAVE AS, the camera saves the <HOLD> proﬁle settings to the CUSTOM proﬁle (refer to

Save As).

MAIN MENU

PROFILES >

EXPOSURE SETTINGS >

FUNCTION SETTINGS >

CAMERA SETUP >

AI AUTO ADJUSTMENT >

PIXEL CORRECTION >

SYSTEM INFORMATION >

EXIT

PROFILES

ACTIVE > STANDARD

SAVE AS > CUSTOM

*DEFAULT STANDARD

BACK EXIT

C2924M (4/05) 27

Table G shows the default camera settings for each proﬁle. Figure 11 shows sample scenes for each camera proﬁle.

Figure 11. Sample Proﬁle Scenes

SAVE AS

Use this option to save all settings from the <HOLD> proﬁle into the CUSTOM proﬁle. After selecting this option, the ACTIVE proﬁle changes to

CUSTOM.

Table G. Settings by Proﬁle

Proﬁle STANDARD (default) DAY&NIGHT WDR GAMING

Exposure Settings

AUTO EXPOSURE NORMAL NORMAL WDR NORMAL

VIDEO LEVEL 0 0 0 0

FLICKERLESS OFF OFF OFF OFF

AGC ON ON ON ON

DSS 4 OFF 4 4

DAY & NIGHT COLOR AUTO COLOR COLOR

D&N DETECTION 5 SEC

D&N FILTER LIMIT 10 MIN

Function Settings

LINE SYNC AUTO AUTO AUTO INTERNAL

WHITE BALANCE AUTO AUTO AUTO INDOOR

MANUAL RED/BLUE DEFAULT DEFAULT DEFAULT DEFAULT

GAMMA 60% (NORM) 60% (NORM) 45%

SHARPNESS -1 -1 -1 -1

E-ZOOM OFF OFF OFF OFF

STANDARD DAY & NIGHT

WDR GAMING

28 C2924M (4/05)

EXPOSURE SETTINGS

Select this option to conﬁgure the exposure settings for the CCC1390H Series camera. The default EXPOSURE SETTINGS menu appears when

AUTO EXPOSURE is set to NORMAL, BLC, or WDR. When AUTO EXPOSURE is set to MANUAL, the FLICKERLESS option is replaced with the

SHUTTER SPEED option.

AUTO EXPOSURE

The automatic exposure feature automatically adjusts the electronic shutter and mechanical iris to set the correct exposure. Select one of the

following automatic exposure modes:

NORMAL Select this mode to use the electronic shutter and mechanical iris to control exposure. As lighting conditions change, the camera

adjusts exposure based on input from the electronic shutter.

BLC Select this mode for scenes that are strongly backlit. The camera corrects the image to bring out the detail of the subject, such

as a person entering a building through a door.

MANUAL Select this mode to set the electronic shutter speed manually (refer to Shutter Speed for more information).

WDR Select this mode for scenes that include both high-light and low-light objects.

The default depends on the selected proﬁle (refer to Table G.)

NOTES:

•You can also use the rear panel button to switch between NORMAL and WDR modes (refer to Quick Setup).

•When you select BLC, the VIDEO LEVEL option is disabled.

•When you select MANUAL, the FLICKERLESS option changes to SHUTTER SPEED. Also, the DSS(SENS) option is disabled.

•When you select WDR, the GAMMA and E-ZOOM options are disabled.

VIDEO LEVEL

Use this option to set the video output voltage from 0.9 Vp-p to 1.1 Vp-p in increments of 0.02 Vp-p. Use it to compensate for signal loss due to

long cable runs. You can also use it to boost the video output.

Select a value between -5 (0.9 Vp-p) and 5 (1.1 Vp-p). The default is 0 (1.0 Vp-p).

NOTE: When AUTO EXPOSURE is set to BLC, you cannot adjust the video level.

FLICKERLESS

In some installations, the cycle of the ﬂuorescent lights may interfere with the electronic iris shutter speed. Use this option to override the shutter

speed. When enabled, the shutter speed is set to 1/100 (NTSC) or 1/120 (PAL).

Select ON or OFF. The default is OFF.

NOTE: This option appears when AUTO EXPOSURE is set to NORMAL, BLC, or WDR.

EXPOSURE SETTINGS

AUTO EXPOSURE > NORMAL

VIDEO LEVEL > 0

FLICKERLESS > OFF

AGC > ON

DSS(SENS) > 4

DAY & NIGHT > COLOR

D&N DETECTION >

D&N FILTER LIMIT >

BACK EXIT

EXPOSURE SETTINGS

AUTO EXPOSURE > MANUAL

VIDEO LEVEL > 0

SHUTTER SPEED > 1/60

AGC > ON

DSS(SENS) > 4

DAY & NIGHT > COLOR

D&N DETECTION >

D&N FILTER LIMIT >

BACK EXIT

NORMAL, BLC, or WDR

AUTO EXPOSURE

MANUAL

AUTO EXPOSURE

C2924M (4/05) 29

SHUTTER SPEED

Use this option to set the shutter speed manually.

Select one of the following options: 1/60(NTSC), 1/50(PAL), 1/100(NTSC), 1/120(PAL), 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000, 1/20000,

1/50000. The default is 1/60(NTSC) or 1/50(PAL).

NOTE: This option appears when AUTO EXPOSURE is set to MANUAL.

AUTOMATIC GAIN CONTROL (AGC)

Automatic gain control (AGC) automatically adjusts the image when the light level changes. Most scenes beneﬁt from AGC operation.

Select ON or OFF. The default is ON.

NOTE: You can also use the rear panel button to enable or disable AGC (refer to Quick Setup).

DIGITAL SLOW SHUTTER (DSS (SENS))

Digital slow shutter (DSS) slows the picture frame rate and increases the camera sensitivity under low-light conditions by increasing the number

of ﬁelds of integration. Use this option to enable or disable this feature, and to set the number of integration ﬁelds.

Select one of the following options: OFF, 2, 4, 6, 8, 10, 20, 40. The default depends on the selected proﬁle (refer to Table G.)

NOTES:

•If you disable SENS on the rear panel, the camera saves the DSS (SENS) value on the EXPOSURE SETTING menu (refer to Quick Setup).

•This option is automatically disabled when AUTO EXPOSURE is set to MANUAL.

•Depending on the number of ﬁelds of integration, the picture will develop a granular appearance and motion may lag, resulting in a stereo-

scopic effect or streaking on fast-moving objects.

DAY AND NIGHT

Use this option to specify how the camera will switch between day (color) and night (black and white) operation.

Select one of the following options:

AUTO Select this option to switch the ﬁlter automatically as light conditions change.

The D&N DETECTION and D&N FILTER LIMIT settings appear.

The camera switches from day to night when the AGC gain level reaches 22 dB.

It switches from night to day when the AGC gain level reaches 16 dB.

When AUTO is selected, both the angle of view and the lighting conditions may

cause the camera ﬁlters to switch constantly. Use the D&N FILTER LIMIT to

compensate for this (refer to Day and Night Filter Limit).

COLOR Select this option to operate the camera in day mode.

BW Select this option to operate the camera in night mode.

EXT. Select this option to use an external signal to switch between day and night modes (refer to Connecting External Control for more

information). The D&N DETECTION and D&N FILTER LIMIT become enabled. In some installations, this option may be more

reliable than AUTO mode.

The default is COLOR, except for the DAY&NIGHT proﬁle, whose default is AUTO.

NOTES:

•You can also use the rear panel button to switch between AUTO and COLOR modes (refer to Quick Setup).

•When AGC is enabled, AUTO and EXT. modes are available. When AGC is disabled, AUTO and EXT. modes are not available; you can select

only COLOR or BW mode.

EXPOSURE SETTINGS

AUTO EXPOSURE > NORMAL

VIDEO LEVEL > 0

FLICKERLESS > OFF

AGC > ON

DSS(SENS) > 4

DAY & NIGHT > COLOR

D&N DETECTION >

D&N FILTER LIMIT >

BACK EXIT

30 C2924M (4/05)

DAY AND NIGHT DETECTION

The camera regularly checks the brightness level. When the brightness level crosses the switch threshold and lasts longer than the

D&N DETECTION setting, the camera switches the ﬁlter.

For example, the headlights of a passing car affect the brightness level in the camera, but not long enough for the ﬁlter to switch. The light of a

cloudy day also affects the brightness level in the camera, long enough for the ﬁlter to switch.

Select one of the following options: 5 SEC, 30 SEC. The default is 5 SEC.

NOTE: This option is only enabled when the DAY & NIGHT option is set to AUTO or EXT.

DAY AND NIGHT FILTER LIMIT

In certain lighting conditions, the brightness level may cross the switch threshold quickly. As a result, the camera may constantly switch ﬁlters.

Use this option to indicate how often to test the brightness level.

Select one of the following detection test intervals:

OFF Select this option to test the brightness level continuously, according to the D&N DETECTION setting (5 seconds or 30 seconds).

10 MIN Select this option to test the brightness level every 10 minutes.

30 MIN Select this option to test the brightness level every 30 minutes.

The default is 10 MIN when the DAY & NIGHT proﬁle is selected. Otherwise, the default is OFF.

After the camera switches ﬁlters three times, and after the ﬁlter limit interval has passed, an asterisk (*) appears next to this setting. This indi-

cates that the detection test has been performed.

NOTE: This option is only enabled when the DAY & NIGHT option is set to AUTO or EXT.

C2924M (4/05) 31

FUNCTION SETTINGS

Select this option to conﬁgure the function settings for the CCC1390H Series camera.

LINE SYNCHRONIZATION

Use line synchronization to eliminate the vertical roll that occurs when multiple cameras are connected to the same switching device. Line

synchronization locks each camera to the same frame rate.

Line Sync

Select one of the following line sync options:

AUTO When using AC power, select this option to operate in line lock mode. This mode

synchronizes the frame rate to the power phase. When selected, you can also

manually set the vertical phase for this camera (refer to V-Phase Adjustment below

and to Camera Synchronization for more information).

INT Select this option to use the internal sync generator.

The default is AUTO, except for the GAMING proﬁle, whose default is INT.

NOTES:

•When using DC power, the camera always uses the internal sync generator.

•When you select INT, the V-PHASE ADJ option is disabled.

V-Phase Adjustment

Use this menu to adjust the vertical phase for line synchronization. The range is 0 to 52 for NTSC

cameras and 0 to 62 for PAL cameras.

Press the button up or down to adjust vertical phase. When correct, press the center of the button to

return to the LINE SYNC menu.

WHITE BALANCE

The CCC1390H Series camera offers four white balance options. White balance settings deﬁne how the camera processes video images to render

true colors in a scene. White balance is especially effective in scenes with changing color temperatures. Use it also in installations with

incandescent, ﬂuorescent, or outdoor lighting.

Select one of the following white balance modes:

AUTO In this mode, the camera automatically adjusts the white balance based on the colors in the camera scene. The camera

continually delivers the best possible image.

MANUAL Use this mode to calibrate the camera to the white balance in a neutral scene. This prevents dominant colors in the target scene

from affecting white balance. Refer to Manual White Balance Calibration for more information.

INDOOR Use this mode for indoor scenes. The white balance gain is set to about 2,800°K and does not change as the scene colors change.

OUTDOOR Use this mode for outdoor scenes. The white balance gain is set to about 6,000°K and does not change as the scene colors

change.

FUNCTION SETTINGS

LINE SYNC >

WHITE BALANCE > AUTO

MANUAL RED/BLUE >

GAMMA > 60%(NORM)

SHARPNESS >

E-ZOOM >

MASKING >

TITLE >

BACK EXIT

LINE SYNC

LINE SYNC > AUTO

V-PHASE ADJ >

BACK EXIT

V-PHASE ADJ

PHASE VALUE = 45

32 C2924M (4/05)

MANUAL RED/BLUE

Select this option to display the MANUAL RED/BLUE menu.

Red Gain

Use this option to either increase or decrease the light level of the red elements in the camera image.

Select a value between -5 and 5. The default is -1.

Blue Gain

Use this option to either increase or decrease the light level of the blue elements in the camera image. Select a value between -5 and 5.

The default is -2.

Red Hue

Use this option to either increase or decrease the red hue in the camera image. Select a value between -5 and 5. The default is 1.

Blue Hue

Use this option to either increase or decrease the blue hue in the camera image. Select a value between -5 and 5. The default is 1.

GAMMA

Gamma correction adjusts the video signal to compensate for the nonlinear response of the monitor display.

Select one of the following options: 60%(NORM), 45%, or 100%. The default depends on the selected proﬁle (refer to Table G).

NOTE: When AUTO EXPOSURE is set to WDR, you cannot change the gamma setting.

SHARPNESS

Select this option to display the SHARPNESS menu.

Aperture Gain

Use this option to increase or decrease the image sharpness, both vertically and horizontally. Select

a value between -5 and 5. The default is -1.

E-ZOOM

Select this option to conﬁgure electronic zoom, including electronic panning.

NOTE: When you enable electronic zoom, both the WDR auto exposure mode and masking are

disabled. If either WDR or masking is active, electronic zoom is disabled.

Zoom

Select one of the following electronic zoom options: OFF, 1.5, 2.0, 2.5. The default is OFF.

Position

Use this option to pan and tilt the electronic zoom frame to a speciﬁc portion of the scene.

To position the electronic zoom frame:

1. Change the ZOOM setting on the E-ZOOM menu to 1.5. Positioning is possible only at 1.5 zoom.

2. Select the POSITION menu. The POSITION menu appears.

3. Press the button up, down, left, or right to position the frame. When correct, press the center of the button to return to the E-ZOOM menu.

4. To use 2.0 or 2.5 zoom, change the ZOOM setting to the desired value.

MANUAL RED/BLUE

RED GAIN > -1

BLUE GAIN > -2

RED HUE > 1

BLUE HUE > 1

BACK EXIT

SHARPNESS

APERTURE GAIN > -1

BACK EXIT

E-ZOOM

ZOOM > OFF

POSITION >

BACK EXIT

POSITION

C2924M (4/05) 33

MASKING

Masking lets you block out certain areas of a camera scene. Select this option to conﬁgure one to

eight masks in the camera image.

NOTE: When you enable masking, electronic zoom is disabled. If electronic zoom is active, masking

is disabled.

Mask

Use this option to enable or disable masking. The default is OFF.

Mask Edit

Use this option to conﬁgure one or more masks. There is no default mask.

To edit a mask:

1. Change the MASK setting on the MASKING menu to ON.

2. Select the MASK EDIT menu. The MASK SETTING menu appears.

3. Use the pointer to conﬁgure the mask area.

a. Press the button up, down, left, or right to move the cursor to the upper left corner of the

mask.

b. Press the center of the button to mark the upper left corner.

c. Press the button up, down, left, or right to move the cursor to the lower right corner of

the mask.

NOTE: If you move the cursor either left or above the start point, the mask edit is cancelled.

d. Press the center of the button to mark the lower right corner. The mask area is blacked out. The MASKING menu appears with the

new mask.

4. Repeat step 3 for each additional mask.

If you add a ninth mask, the camera erases the ﬁrst mask. You cannot conﬁgure more than eight masks.

Mask Erase

Select this option to erase one or more masks. The camera erases masks from the last created to the ﬁrst created.

To erase a mask, select MASK ERASE. The mask that was last created disappears. Repeat to erase additional masks.

TITLE

Select this option to conﬁgure the camera title.

Title

Use this option to enable or disable the title display. The default is OFF.

Title Edit

Use this option to enter or edit the camera title, up to 16 characters. The default is blank.

To enter a camera title:

1. Change the TITLE setting on the TITLE menu to ON.

2. Select the EDIT TITLE menu. The EDIT TITLE menu appears.

3. Press the button up, down, left, or right to move the cursor to the desired character.

The space character is located below the letter n.

4. Press the center of the button to select the character. The selected character appears in the

blank area at the bottom of the screen.

MASKING

MASK > OFF

MASK EDIT >

MASK ERASE

BACK EXIT

MASK SETTING

TITLE

TITLE > OFF

EDIT TITLE >

BACK EXIT

EDIT TITLE

ABCDEFGHIJKLM

NOPQRSTUVWXYZ

abcdefghijklm

nopqrstuvwxyz

0123456789-/

BACK BS

_________________

34 C2924M (4/05)

5. To clear a character, select BS (backspace). The camera deletes the last character entered.

6. Repeat steps 3 and 4 until you have entered the camera title.

7. When the title is correct, select BACK to return to the TITLE menu.

CAMERA SETUP

Select this option to conﬁgure the serial communication and rear panel function settings for the

CCC1390H Series camera. Refer to Connecting External Control for information on wiring the serial

interface.

Address

The CCC1390H Series camera can be accessed remotely from selected Pelco controllers. Use this

option to assign a receiver address to the camera. This address identiﬁes the camera on the serial

chain. Select a value from 1 to 30. The default is 1.

NOTES:

•Each camera must have a unique address.

•Be sure to assign the address before accessing the camera remotely.

COM Speed

Use this option to set the communication or baud rate for this camera. This must match the setting for the other cameras and controllers on the

serial chain. Select one of the following: 2400, 4800, 9600, 19200. The default is 4800.

LED

Select this option to enable or disable the rear panel indicators. The default is ON.

Switch

Select this option to enable or disable quick setup on the rear panel (refer to Quick Setup). The default is ON.

AUTO IRIS LENS ADJUSTMENT

Select this option to adjust the electronic properties of the auto iris lens to the auto iris electronic

properties of the camera. Perform this procedure before using the camera or each time you change

the lens.

To perform this procedure:

1. Mount the auto iris lens to the camera (refer to Lens Mounting).

2. Aim the camera at a bright, ﬂickerless scene.

3. Select AI AUTO ADJUSTMENT. The AI AUTO ADJUSTMENT menu appears.

4. Select OK. The camera performs the procedure. Then the MAIN MENU appears.

CAMERA SETUP

ADDRESS > 1

COM SPEED > 4800

LED > ON

SWITCH > ON

BACK EXIT

AI AUTO ADJUSTMENT

OK CANCEL

C2924M (4/05) 35

PIXEL CORRECTION

If white spots appear in the video image, one or more pixels on the camera imager may be defective.

This condition is common to CCD camera imagers.

Select this option to automatically detect and correct these defects. This feature helps you maintain

image quality.

To perform this procedure:

1. Use a lens cap to cover the lens. Make sure no light can enter the lens.

NOTE: The mechanical iris lens aperture does not completely block the light. Therefore, you should use a lens cap.

2. Select PIXEL CORRECTION. The PIXEL CORRECTION menu appears.

3. Select OK. The camera performs the procedure. Then the MAIN MENU appears.

NOTES:

•Any defective pixels that cannot be completely corrected may still appear.

•Defective pixels may reappear when DSS(SENS) is enabled.

SYSTEM INFORMATION

Select this option to display the camera ﬁrmware information.

Restore Factory Settings

Select this option to reset the camera to the factory default settings. This option clears all saved

user-deﬁnable settings, except the following:

•CAMERA SETUP menu: ADDRESS, COM SPEED

•LINE SYNC menu: V-PHASE ADJ

•PIXEL CORRECTION

To restore factory default settings:

1. Select RESTORE FACTORY SETTINGS on the SYSTEM INFORMATION menu. The RESTORE

FACTORY SETTINGS menu appears.

2. Select OK. The camera resets all parameters to the factory default settings, except those listed above. Then the MAIN MENU appears.

PIXEL CORRECTION

COVER THE LENS

AND SELECT OK

OK CANCEL

SYSTEM INFORMATION

FIRMWARE VERSION 1.0

OSD VERSION 1.0

RESTORE FACTORY SETTINGS >

BACK EXIT

RESTORE FACTORY SETTINGS

OK CANCEL

36 C2924M (4/05)

Lens Focusing

After mounting the lens, you must focus your CCC1390H Series camera. You will adjust both the back focus (on the camera) and the ﬁne focus (on

the lens).

NOTE: The back focus has already been adjusted using a standard CS-mount lens. However, you might need to adjust it again to match the

mounted lens.

1. Auto iris only: Cover the auto iris lens with a suitable neutral density (ND) ﬁlter. This opens the iris fully. For best results, use an ND3 ﬁlter.

2. Manual iris only: Open the iris completely. Refer to Figure 12, which shows the manual iris, varifocal, and lens focus locking screws for a

sample lens. Refer to your lens documentation for more information.

Figure 12. Lens Focus

3. If necessary, enable Automatic Gain Control (AGC) on the EXPOSURE SETTINGS menu.

AGC is enabled by default.

a. Display the EXPOSURE SETTINGS menu.

b. Change AGC to ON.

c. Select EXIT to save the AGC setting.

4. Aim the camera at the farthest object in the ﬁeld of view. Make sure it is at least 6.5 ft

(2 m) away.

5. Fixed focal length lens only:

a. Set the lens focal length to far (∞).

b. Adjust the back focus:

(1) Use a 1.5-mm Allen wrench to loosen the back focus locking screw.

(2) Turn the lens until the image is focused.

(3) Tighten the back focus locking screw clockwise.

Back focus is a coarse adjustment. You will make the ﬁne focus adjustment in the next step.

c. Adjust the lens focus to achieve the best ﬁne focus.

WARNING: Do not over-tighten the back focus locking screw because you may damage the camera.

1.5 MM

ALLEN

WRENCH

VARIFOCAL

LOCKING

SCREW

LENS FOCUS

LOCKING SCREW

MANUAL IRIS

LOCKING SCREW

MAIN MENU

PROFILES >

EXPOSURE SETTINGS >

FUNCTION SETTINGS >

CAMERA SETUP >

AI AUTO ADJUSTMENT >

PIXEL CORRECTION >

SYSTEM INFORMATION >

EXIT

EXPOSURE SETTINGS

AUTO EXPOSURE > NORMAL

VIDEO LEVEL > 0

FLICKERLESS > OFF

AGC > ON

DSS(SENS) > 4

DAY & NIGHT > COLOR

D&N DETECTION >

D&N FILTER LIMIT >

BACK EXIT

C2924M (4/05) 37

6. Varifocal lens only:

a. Set the varifocal to wide (W) and the lens focal length to far (∞).

b. Adjust the back focus:

(1) Use the enclosed 1.5-mm Allen wrench to loosen the back focus locking screw.

(2) Turn the lens until the image is focused.

(3) Tighten the back focus locking screw clockwise.

Back focus is a coarse adjustment. You will make the ﬁne focus adjustment in steps c and d.

c. Move the varifocal locking screw up or down to set the ﬁeld of view.

d. Adjust the lens focus to achieve the best ﬁne focus.

e. Repeat steps c and d until the focus is correct.

7. Manual iris only: Adjust the iris for the best picture quality. The largest aperture gives the best light sensitivity; the smallest aperture

gives the greatest depth of ﬁeld.

8. Tighten all lens locking screws.

NOTE: When tightening the lens locking screws, do not over-turn or force any screw.

9. Auto iris only: Remove the ND ﬁlter.

10. If necessary, disable AGC.

a. Display the EXPOSURE SETTINGS menu.

b. Change AGC to OFF.

c. Select EXIT to save the AGC setting.

11. Auto iris only: Perform the auto iris lens adjustment procedure (refer to Auto Iris Lens

Adjustment).

12. As soon as you ﬁnish customizing this and all other camera settings, save your custom

settings into the CUSTOM proﬁle. This protects them in case the camera loses power

or must be restarted (refer to Proﬁles for more information).

WARNING: Do not over-tighten the back focus locking screw because you may damage the camera.

MAIN MENU

PROFILES >

EXPOSURE SETTINGS >

FUNCTION SETTINGS >

CAMERA SETUP >

AI AUTO ADJUSTMENT >

PIXEL CORRECTION >

SYSTEM INFORMATION >

EXIT

EXPOSURE SETTINGS

AUTO EXPOSURE > NORMAL

VIDEO LEVEL > 0

FLICKERLESS > OFF

AGC > OFF

DSS(SENS) > 4

DAY & NIGHT > COLOR

D&N DETECTION >

D&N FILTER LIMIT >

BACK EXIT

38 C2924M (4/05)

Camera Synchronization

Camera synchronization may affect installations that use two or more AC power supplies for multiple cameras. Due to different power phases,

a brief vertical roll may appear on the monitor when switching between cameras. To eliminate this vertical roll, adjust the phase control to

synchronize the cameras to one another.

It may be necessary for two people to communicate when synchronizing cameras, one at the camera and the other at the monitor, to observe the

vertical roll and the effect of any camera adjustments.

To synchronize cameras:

1. Choose a reference camera to which all other cameras will be phased.

2. Access V-PHASE ADJ menu for a camera. Press the button up and down to adjust the vertical phase until the camera is synchronized to the

reference camera.

A dual trace oscilloscope is recommended, but not required, to adjust camera phase. Align the vertical sync pulses of the reference camera

to the selected camera.

3. After each adjustment, switch back and forth between the adjusted camera and the reference camera. Repeat this process until the roll

between the cameras disappears completely.

4. Adjust the phase of all other cameras by repeating steps 2 and 3. Always adjust to the reference camera selected in step 1.

5. As soon as you ﬁnish customizing this and all other camera settings, save your custom settings into the CUSTOM proﬁle. This protects them

in case the camera loses power or must be restarted (refer to Proﬁles for more information).

To adjust phase control:

1. Select LINE SYNC on the FUNCTION SETTINGS menu. The LINE

SYNC menu appears.

2. Switch the LINE SYNC setting to AUTO.

3. Select V-PHASE ADJ. The V-PHASE ADJ menu appears.

4. Press the button up or down to change the PHASE VALUE. On the

CCC1390H-6 (NTSC) camera, the range is 0 to 52. On the

CCC1390H-6X (PAL) camera, the range is 0 to 62.

5. Press the center of the button to return to the LINE SYNC menu.

6. Select EXIT to close the setup menus.

7. As soon as you ﬁnish customizing this and all other camera settings, save your custom settings into the CUSTOM proﬁle. This protects them

in case the camera loses power or must be restarted (refer to Proﬁles for more information).

MAIN MENU

PROFILES >

EXPOSURE SETTINGS >

FUNCTION SETTINGS >

CAMERA SETUP >

AI AUTO ADJUSTMENT >

PIXEL CORRECTION >

SYSTEM INFORMATION >

EXIT

FUNCTION SETTINGS

LINE SYNC >

WHITE BALANCE > AUTO

MANUAL RED/BLUE >

GAMMA > 60%(NORM)

SHARPNESS >

E-ZOOM >

MASKING >

TITLE >

BACK EXIT

LINE SYNC

LINE SYNC > AUTO

V-PHASE ADJ >

BACK EXIT

V-PHASE ADJ

PHASE VALUE = 45

C2924M (4/05) 39

Manual White Balance Calibration

In some installations, use manual white balance to render the most accurate image color possible. Mixed color applications may affect the

amount of color adjustment. For example, a small white object on a large blue surface may have a reddish tint. Manual white balance uses a

calibration image to identify the correct white level. The camera then uses this white level when adjusting overall image color.

NOTE: Manual white balance is recommended only for indoor applications that have a single primary light source.

Example: A CCC1390H camera is installed in a pan/tilt enclosure in a clothing store in a shopping mall. Mixed colors are located throughout the

store. Overhead lights provide the primary illumination, but some light also enters the store from the mall. As the camera pans a section ﬁlled with

blue clothing, the camera may redden the image to compensate for the blue. When properly calibrated, the camera will not try to adjust scenes

with predominant amounts of red or blue.

To calibrate the manual white balance:

1. Focus the camera on a neutral color scene. Select a neutral scene with the following characteristics:

•Little or no black

•Not predominantly red

•Not predominantly blue

•No direct light source, such as a lamp or a window

2. Select WHITE BALANCE on the FUNCTION SETTINGS menu.

3. Select AUTO. This calibrates the white balance gain to the neutral scene.

4. Change WHITE BALANCE from AUTO to MANUAL. This locks the white balance

gain into camera memory.

NOTE: If you change WHITE BALANCE from MANUAL to a different mode, the stored

manual white balance settings are erased. You will have to perform this procedure again.

5. Select EXIT to close the setup menus.

6. Focus the camera on the target scene.

7. As soon as you ﬁnish customizing this and all other camera settings, save your custom settings into the CUSTOM proﬁle. This protects them

in case the camera loses power or must be restarted (refer to Proﬁles for more information).

MAIN MENU

PROFILES >

EXPOSURE SETTINGS >

FUNCTION SETTINGS >

CAMERA SETUP >

AI AUTO ADJUSTMENT >

PIXEL CORRECTION >

SYSTEM INFORMATION >

EXIT

FUNCTION SETTINGS

LINE SYNC >

WHITE BALANCE > AUTO

MANUAL RED/BLUE >

GAMMA > 60%(NORM)

SHARPNESS >

E-ZOOM >

MASKING >

TITLE >

BACK EXIT

40 C2924M (4/05)

Speciﬁcations

GENERAL

Day/Night Operation

Day Infrared (IR) cut ﬁlter

Night BK-7 glass, same optical displacement as day

Imaging Device 1/3-inch image format Sony SS-2WD CCD

Dynamic Range 60 dB maximum (WDR mode)

Picture Elements

NTSC 768 (H) x 494 (V) (approx. 380K)

PAL 752 (H) x 582 (V) (approx. 440K)

Sensing Area 3/16 x 1/8-inch (4.76 x 3.18 mm)

Scanning System 525 (NTSC)/625 (PAL), 2:1 interlace

Synchronization Internal/AC line lock

Horizontal Resolution 530 TV lines (B-W); 480 TV lines (color)

Iris Control Selectable: on/off

Electronic Shutter Control Selectable: on/off

NTSC 1/60-1/50,000

PAL 1/50-1/50,000

Auto Iris Lens Type DC-drive (autosensing)

Sensitivity

Color 0.8 lux, F1.2, 40 IRE, AGC on, 75% scene reﬂectance

Color (SENS 40x) 0.02 lux, F1.2, 40 IRE, AGC on, 75% scene reﬂectance

B-W 0.08 lux, F1.2, 40 IRE, AGC on, 75% scene reﬂectance

Digital Slow Shutter (SENS) 2x, 4x, 6x, 8x, 10x, 20x, 40x

Filter Switching Threshold

Day to Night 1.6 lux, average scene illumination

Night to Day 1.9 lux, average scene illumination

Signal-to-Noise Ratio >48 dB

Vertical Phase Adjustable ±90˚

Automatic Gain Control Selectable: on/off, adjustable to 24 dB

Backlight Compensation Selectable: on/off

Flickerless Mode Selectable: on/off; 1/100 sec (NTSC),

1/120 sec (PAL)

Internal Synchronization Selectable: on/off

Auto White Balance Selectable: on/off, 4 modes

Day/Night Selectable: on/off, 4 modes

Signal Processing Digital signal processing (DSP)

Video Output 1 Vp-p, 75

Gamma Correction Selectable: on/off, 0.45, 0.6, 1.0

Electronic PTZ Selectable: 1.5X, 2.0X, 2.5X

White Balance Range 2,500° to 8,600°K

C2924M (4/05) 41

ELECTRICAL

Power Requirements

CCC1390H-6 24 VAC ±15%/12 VDC ±15%, 60 Hz

CCC1390H-6X 24 VAC ±15%/12 VDC ±15%, 50 Hz

Power Consumption 3.5 watts: 270 mA, 24 VAC; 390 mA, 12 VDC

Power Connector 3-pin terminal strip, push-in type

Video Connector BNC

Auto Iris Connector 4-pin connector (miniature square)

Mode Indicators 4

Controls 5-position switch

Serial data termination switch

Control Connector 7-pin micro (1.25 mm) connector

Data I/O (Pelco P or Pelco D protocol)

External day/night switch

MECHANICAL

Lens Mount CS mount

Camera Mount 1/4-inch UNC-20 screw, top or bottom of camera housing

ENVIRONMENTAL

Operating Temperature 14° to 122°F (-10° to 50°C)

Storage Temperature -40° to 140°F (-40° to 60°C)

Humidity 20% to 80% (noncondensing)

PHYSICAL

Dimensions 2.2” D x 2.09” W x 2.17” H

(5.6 x 5.3 x 5.5 cm)

Weight (without lens) 0.44 lb (0.20 kg)

Shipping Weight 1 lb (0.45 kg)

(Design and product speciﬁcations subject to change without notice.)

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or

workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series ﬁber optic products.

• Three years on Genex® Series products (multiplexers, server, and keyboard).

•Three years on Camclosure® and ﬁxed camera models, except the CC3701H-2,

CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,

which have a ﬁve-year warranty.

•Two years on standard motorized or ﬁxed focal length lenses.

•Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series

ﬁxed dome products.

•Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in

continuous motion applications.

•Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).

•Eighteen months on DX Series digital video recorders, NVR300 Series network video

recorders, and Endura™ Series distributed network-based video products.

•One year (except video heads) on video cassette recorders (VCRs). Video heads will be

covered for a period of six months.

•Six months on all pan and tilts, scanners or preset lenses used in continuous motion

applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco

shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,

California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident

are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from

the speciﬁc use or application made of the Products. Pelco’s liability for any claim, whether

based on breach of contract, negligence, infringement of any rights of any party or product

liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for

such Products. In no event will Pelco be liable for any special, incidental or consequential

damages (including loss of use, loss of proﬁt and claims of third parties) however caused,

whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with speciﬁc legal rights. The Dealer may also have

additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or

(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following

information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the

warranty conditions stated above, please include a written explanation with the product

when returned.

Method of return shipment shall be the same or equal to the method by which the item was

received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at

(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned

for credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing

charge.

Goods returned for repair or credit should be clearly identiﬁed with the assigned CA or RA

number and freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department

Pelco

3500 Pelco Way

Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are

instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco

3500 Pelco Way

Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors

473 Eccles Avenue

South San Francisco, CA 94080 USA

Phone: 650-737-1700

Fax: 650-737-0933

REVISION HISTORY

Manual # Date Comments

C2924M 4/05 Original version.

PelcoNet, Endura, and ExSite are trademarks of Pelco.

Worldwide Headquarters

3500 Pelco Way

Clovis, California 93612 USA

USA & Canada

Tel: 800/289-9100

Fax: 800/289-9150

International

Tel: 1-559/292-1981

Fax: 1-559/348-1120

www.pelco.com

ISO

9001

United States

Canada

United Kingdom

The Netherlands

Singapore

Spain

Scandinavia

France

Middle East

Pelco Ccc1390H Series Camera C2924M 4 05 Users Manual

C2924M (405) to the manual 0c58c403-41d0-41cc-84aa-cbd75f03e894

Navigation menu

Versions of this User Manual:

Views

Navigation