Pelco In Ceiling Mount Black Box Spectra Iv Users Manual Pelco_Spectra_IV_in_Ceilings_Back_Box_manual
Spectra IV SE to the manual 24b422c9-735c-4661-abe5-b088f1dff593
2015-02-02
: Pelco Pelco-In-Ceiling-Mount-Black-Box-Spectra-Iv-Users-Manual-440812 pelco-in-ceiling-mount-black-box-spectra-iv-users-manual-440812 pelco pdf
Open the PDF directly: View PDF 
.
Page Count: 16
| Download | |
| Open PDF In Browser | View PDF |
I N S T A L L A T I O N Spectra® IV Series Spectra® IV SE Series In-Ceiling Mount Back Box C3417M-B (11/06) Installation 1 2 4 5 3 2 C3417M-B (11/06) 1. Locate the center point of the mounting location and insert the compass tool. Draw a circle. 2. Cut the circle out of the ceiling. 3. Attach the conduit fitting, lock nut, and safety chain bracket. Install a safety chain/cable (not supplied) that will support up to 16 pounds (7.3 kg). 4. Open the hinged door to the back box. Push the tab lock towards the wall of the unit and lift the door open. Pull wiring into the back box through the conduit fitting. Refer to Table A, Table B, and Table C for wiring distances. 5. Install the back box by compressing the spring clips and pushing the back box through the hole. Tighten the screws until you hear a clicking noise. Table B. 24 VAC/24VDC Wiring Distances Table A. Video Coaxial Cable Requirements Cable Type* Maximum Distance RG59/U 750 ft (229 m) RG6/U 1,000 ft (305 m) RG11/U 1,500 ft (457 m) *Cable requirements: 75 ohms impedance All-copper center conductor All-copper braided shield with 95% braid coverage The following are the recommended maximum distances for 24 VAC and 24 VDC applications and are calculated with a 10 percent voltage drop. (Ten percent is generally the maximum allowable voltage drop for AC- or DC-powered devices.) Wire Gauge AC/DC Total VA/ Total Watts 20 AWG (0.5 mm2) 18 AWG (1.0 mm2) 16 AWG (1.5 mm2) 14 AWG (2.5 mm2) 23 VA/ 15 watts 123 ft (38 m) 196 ft (60 m) 311 ft (95 m) 495 ft (151 m) 73 VA/ 65 watts 39 ft (12 m) 62 ft (19 m) 98 ft (30 m) 156 ft (48 m) NOTE: Input power for the dome is 24 VAC or 24 VDC. Using 24 VAC input power, power consumption is 23 VA per dome for indoor models and 73 VA for outdoor models. Using 24 VDC input power, power consumption is 0.7 A (15 watts) for indoor models and 3 A (65 watts) for outdoor models. Use a 24 VAC transformer with the following minimum VA: 40 VA per dome For indoor models (without heater) 100 VA per dome For outdoor models (with heater) . Table C. UTP Wiring Distances Receiver Maximum Distance Active (Video Only) 0-3,000 ft (0-914.4 m) Passive (Video, Coaxitron, Pelco V-Sync) 0-750 ft (0-228.6 m) NOTE: As a minimum, UTP requires Cat5, 100-ohm twisted pair cable. C3417M-B (11/06) 3 6 7 ALARMS AUX1 1 2 3 4 5 6 7 GND NO COM NC AUX2 GND VIDEO PWR- GND PWR+ RX- RX+ TX- TX+ UTP+ UTP- 4 C3417M-B (11/06) 6. Suspended Ceiling Only: Install the ceiling tile with the back box. Attach a T-rail clip on each side of the ceiling tile. WARNING: An electrical short in the back box may occur if the metal BNC connector is not completely covered by the protective boot. 7. Connect wiring to the circuit board inside the back box. When finished, close the door to the back box and turn on the power. The green LED will light. NOTES: C3417M-B (11/06) • Aux 1: Maximum 2 A at low voltage (<40 V) Aux 2: Maximum 30 mA at 32 VDC • If you are using both unshielded twisted pair (UTP) wiring and a translator board, install the UTP wiring before installing the translator board. • If you are installing an environmental back box in a railway application, attach a ground wire from the circuit board power connector to a structural ground using at least 18-gauge wire. 5 8 SWITCH 1 AND 2 10 A 9 6 C3417M-B (11/06) 8. Configure DIP switches SW1 and SW2 located on the top of the dome drive. For DIP switch settings, refer to the labels located on the top of the dome drive or to the Switch Settings section. NOTE: When connecting more than one Spectra® dome to a single controller, terminate the unit farthest from the controller. To terminate the dome drive set the SW2-10 switch to the ON position. 9. Install the dome drive. Refer to Table D for a list of compatible dome drives and back boxes. Line up the blue and red tabs with the blue and red arrows on the hinged door inside the back box. Push in on the tabs. Insert one side and then the other side. Continue pushing on the ends of the tabs until both sides click into place. Table D. Spectra Dome Drive and Back Box Compatibility Dome Drive ® Spectra II Spectra III™ Spectra IV Spectra II • • • Back Box Spectra III Spectra IV • • • • 10. Install the lower dome. Snap the clip on the end of the trim ring leash into the hole on the lip of the back box. Snap the trim ring into the plastic snap washers on the mounting screws. To use your dome, refer to the operation and programming manual. C3417M-B (11/06) 7 Troubleshooting If your dome does not power up properly after installation, use the following steps. 1. Check the fuse on the circuit board inside the back box for continuity. Replace the fuse if needed. 2. Check the wiring with a volt meter to ensure proper voltage is being received into the back box. If your dome powers up correctly, but you do not have accurate control, use the following steps. 1. Check the signal with a volt meter or an oscilloscope. NOTE: This step will not apply if you are using Coaxitron control. 2. Ensure that the switch settings on the dome drive are set correctly. Refer to the Switch Settings section. 3. If you are using a Pelco controller, ensure that the factory-installed 16-pin jumper has not been removed. If you are using a third-party controller, a TXB Series translator board must be installed. The dome will not function without this 16-pin jumper or a translator board installed. 8 C3417M-B (11/06) Switch Settings WARNING: If you are using D-type or P-type control, your system may not operate if the baud rate and address switches are not set correctly. The switches are set at the factory at the defaults for D-type control (2400 baud and address 1). Table E. Switch Settings for SW2 Special Systems Switch Number AD-32 Preset System 1 2 3 4 5 6 7 8 9 10 ON CM9502 Setting ON Vicon Not currently available; SW2-3 is reserved for future use. Serial Port Settings Switch Number 4 5 RS422 1 2 3 OFF OFF 6 7 8 9 10 RS485, Four Wire OFF ON RS485, Two Wire ON ON 4 5 6 7 8 9 10 2400 Baud (Default for D-type Control) OFF OFF OFF 4800 Baud (Default for P-type Control) ON OFF OFF 9600 Baud OFF ON OFF 6 7 8 9 10 D or P Protocol Baud Rate Switch Number 1 2 3 Video Cable Type Switch Number 1 2 3 4 5 Coax Cable OFF UTP Cable ON Dome Termination Switch Number 1 2 3 4 5 6 7 8 9 10 Terminated ON Not Terminated OFF C3417M-B (11/06) 9 Table F. Switch Settings for SW1, P-Type Control NOTE: For Coaxitron controls, SW1 is not used; set all switches OFF. For D-type control systems, refer to Table G. SWITCH SETTING SPECTRA ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 1 OFF OFF OFF OFF 2 ON OFF OFF 3 OFF ON 4 ON ON 5 OFF OFF ON 6 ON OFF ON 7 OFF ON ON SWITCH SETTING SW1-5 SPECTRA ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 OFF 17 OFF OFF OFF OFF ON OFF OFF 18 ON OFF OFF OFF ON OFF OFF OFF 19 OFF ON OFF OFF ON OFF OFF OFF 20 ON ON OFF OFF ON OFF OFF 21 OFF OFF ON OFF ON OFF OFF 22 ON OFF ON OFF ON OFF OFF 23 OFF ON ON OFF ON ON 8 ON ON ON OFF OFF 24 ON ON ON OFF 9 OFF OFF OFF ON OFF 25 OFF OFF OFF ON ON 10 ON OFF OFF ON OFF 26 ON OFF OFF ON ON 11 OFF ON OFF ON OFF 27 OFF ON OFF ON ON 12 ON ON OFF ON OFF 28 ON ON OFF ON ON 13 OFF OFF ON ON OFF 29 OFF OFF ON ON ON ON 14 ON OFF ON ON OFF 30 ON OFF ON ON 15 OFF ON ON ON OFF 31 OFF ON ON ON ON 16 ON ON ON ON OFF 32 ON ON ON ON ON Table G. Switch Settings for SW1, D-Type Control NOTE: For Coaxitron controls, SW1 is not used; set all switches OFF. For P-type control systems, refer to Table F. SWITCH SETTING SPECTRA ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 10 SWITCH SETTING SPECTRA ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 1 ON OFF OFF OFF OFF OFF OFF OFF 16 OFF OFF OFF OFF ON OFF OFF OFF 2 OFF ON OFF OFF OFF OFF OFF OFF 17 ON OFF OFF OFF ON OFF OFF OFF 3 ON ON OFF OFF OFF OFF OFF OFF 18 OFF ON OFF OFF ON OFF OFF OFF 4 OFF OFF ON OFF OFF OFF OFF OFF 19 ON ON OFF OFF ON OFF OFF OFF 5 ON OFF ON OFF OFF OFF OFF OFF 20 OFF OFF ON OFF ON OFF OFF OFF 6 OFF ON ON OFF OFF OFF OFF OFF 21 ON OFF ON OFF ON OFF OFF OFF 7 ON ON ON OFF OFF OFF OFF OFF 22 OFF ON ON OFF ON OFF OFF OFF 8 OFF OFF OFF ON OFF OFF OFF OFF 23 ON ON ON OFF ON OFF OFF OFF 9 ON OFF OFF ON OFF OFF OFF OFF 24 OFF OFF OFF ON ON OFF OFF OFF 10 OFF ON OFF ON OFF OFF OFF OFF 25 ON OFF OFF ON ON OFF OFF OFF 11 ON ON OFF ON OFF OFF OFF OFF 26 OFF ON OFF ON ON OFF OFF OFF 12 OFF OFF ON ON OFF OFF OFF OFF 27 ON ON OFF ON ON OFF OFF OFF 13 ON OFF ON ON OFF OFF OFF OFF 28 OFF OFF ON ON ON OFF OFF OFF 14 OFF ON ON ON OFF OFF OFF OFF 29 ON OFF ON ON ON OFF OFF OFF 15 ON ON ON ON OFF OFF OFF OFF 30 OFF ON ON ON ON OFF OFF OFF C3417M-B (11/06) SWITCH SETTING SPECTRA ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 SWITCH SETTING SPECTRA ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 31 ON ON ON ON ON OFF OFF OFF 71 ON ON ON OFF OFF OFF ON OFF 32 OFF OFF OFF OFF OFF ON OFF OFF 72 OFF OFF OFF ON OFF OFF ON OFF 33 ON OFF OFF OFF OFF ON OFF OFF 73 ON OFF OFF ON OFF OFF ON OFF 34 OFF ON OFF OFF OFF ON OFF OFF 74 OFF ON OFF ON OFF OFF ON OFF 35 ON ON OFF OFF OFF ON OFF OFF 75 ON ON OFF ON OFF OFF ON OFF 36 OFF OFF ON OFF OFF ON OFF OFF 76 OFF OFF ON ON OFF OFF ON OFF 37 ON OFF ON OFF OFF ON OFF OFF 77 ON OFF ON ON OFF OFF ON OFF 38 OFF ON ON OFF OFF ON OFF OFF 78 OFF ON ON ON OFF OFF ON OFF 39 ON ON ON OFF OFF ON OFF OFF 79 ON ON ON ON OFF OFF ON OFF 40 OFF OFF OFF ON OFF ON OFF OFF 80 OFF OFF OFF OFF ON OFF ON OFF 41 ON OFF OFF ON OFF ON OFF OFF 81 ON OFF OFF OFF ON OFF ON OFF 42 OFF ON OFF ON OFF ON OFF OFF 82 OFF ON OFF OFF ON OFF ON OFF OFF 43 ON ON OFF ON OFF ON OFF OFF 83 ON ON OFF OFF ON OFF ON 44 OFF OFF ON ON OFF ON OFF OFF 84 OFF OFF ON OFF ON OFF ON OFF 45 ON OFF ON ON OFF ON OFF OFF 85 ON OFF ON OFF ON OFF ON OFF OFF 46 OFF ON ON ON OFF ON OFF OFF 86 OFF ON ON OFF ON OFF ON 47 ON ON ON ON OFF ON OFF OFF 87 ON ON ON OFF ON OFF ON OFF 48 OFF OFF OFF OFF ON ON OFF OFF 88 OFF OFF OFF ON ON OFF ON OFF 49 ON OFF OFF OFF ON ON OFF OFF 89 ON OFF OFF ON ON OFF ON OFF 50 OFF ON OFF OFF ON ON OFF OFF 90 OFF ON OFF ON ON OFF ON OFF 51 ON ON OFF OFF ON ON OFF OFF 91 ON ON OFF ON ON OFF ON OFF 52 OFF OFF ON OFF ON ON OFF OFF 92 OFF OFF ON ON ON OFF ON OFF 53 ON OFF ON OFF ON ON OFF OFF 93 ON OFF ON ON ON OFF ON OFF 54 OFF ON ON OFF ON ON OFF OFF 94 OFF ON ON ON ON OFF ON OFF 55 ON ON ON OFF ON ON OFF OFF 95 ON ON ON ON ON OFF ON OFF 56 OFF OFF OFF ON ON ON OFF OFF 96 OFF OFF OFF OFF OFF ON ON OFF 57 ON OFF OFF ON ON ON OFF OFF 97 ON OFF OFF OFF OFF ON ON OFF 58 OFF ON OFF ON ON ON OFF OFF 98 OFF ON OFF OFF OFF ON ON OFF 59 ON ON OFF ON ON ON OFF OFF 99 ON ON OFF OFF OFF ON ON OFF 60 OFF OFF ON ON ON ON OFF OFF 100 OFF OFF ON OFF OFF ON ON OFF 61 ON OFF ON ON ON ON OFF OFF 101 ON OFF ON OFF OFF ON ON OFF 62 OFF ON ON ON ON ON OFF OFF 102 OFF ON ON OFF OFF ON ON OFF OFF 63 ON ON ON ON ON ON OFF OFF 103 ON ON ON OFF OFF ON ON 64 OFF OFF OFF OFF OFF OFF ON OFF 104 OFF OFF OFF ON OFF ON ON OFF 65 ON OFF OFF OFF OFF OFF ON OFF 105 ON OFF OFF ON OFF ON ON OFF 66 OFF ON OFF OFF OFF OFF ON OFF 106 OFF ON OFF ON OFF ON ON OFF 67 ON ON OFF OFF OFF OFF ON OFF 107 ON ON OFF ON OFF ON ON OFF 68 OFF OFF ON OFF OFF OFF ON OFF 108 OFF OFF ON ON OFF ON ON OFF 69 ON OFF ON OFF OFF OFF ON OFF 109 ON OFF ON ON OFF ON ON OFF 70 OFF ON ON OFF OFF OFF ON OFF 110 OFF ON ON ON OFF ON ON OFF C3417M-B (11/06) 11 SWITCH SETTING SPECTRA ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 12 SWITCH SETTING SPECTRA ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 111 ON ON ON ON OFF ON ON OFF 151 ON ON ON OFF ON OFF OFF 112 OFF OFF OFF OFF ON ON ON OFF 152 OFF OFF OFF ON ON OFF OFF ON ON 113 ON OFF OFF OFF ON ON ON OFF 153 ON OFF OFF ON ON OFF OFF ON 114 OFF ON OFF OFF ON ON ON OFF 154 OFF ON OFF ON ON OFF OFF ON 115 ON ON OFF OFF ON ON ON OFF 155 ON ON OFF ON ON OFF OFF ON ON 116 OFF OFF ON OFF ON ON ON OFF 156 OFF OFF ON ON ON OFF OFF 117 ON OFF ON OFF ON ON ON OFF 157 ON OFF ON ON ON OFF OFF ON 118 OFF ON ON OFF ON ON ON OFF 158 OFF ON ON ON ON OFF OFF ON 119 ON ON ON OFF ON ON ON OFF 159 ON ON ON ON ON OFF OFF ON 120 OFF OFF OFF ON ON ON ON OFF 160 OFF OFF OFF OFF OFF ON OFF ON 121 ON OFF OFF ON ON ON ON OFF 161 ON OFF OFF OFF OFF ON OFF ON 122 OFF ON OFF ON ON ON ON OFF 162 OFF ON OFF OFF OFF ON OFF ON ON 123 ON ON OFF ON ON ON ON OFF 163 ON ON OFF OFF OFF ON OFF 124 OFF OFF ON ON ON ON ON OFF 164 OFF OFF ON OFF OFF ON OFF ON 125 ON OFF ON ON ON ON ON OFF 165 ON OFF ON OFF OFF ON OFF ON 126 OFF ON ON ON ON ON ON OFF 166 OFF ON ON OFF OFF ON OFF ON 127 ON ON ON ON ON ON ON OFF 167 ON ON ON OFF OFF ON OFF ON 128 OFF OFF OFF OFF OFF OFF OFF ON 168 OFF OFF OFF ON OFF ON OFF ON 129 ON OFF OFF OFF OFF OFF OFF ON 169 ON OFF OFF ON OFF ON OFF ON 130 OFF ON OFF OFF OFF OFF OFF ON 170 OFF ON OFF ON OFF ON OFF ON 131 ON ON OFF OFF OFF OFF OFF ON 171 ON ON OFF ON OFF ON OFF ON 132 OFF OFF ON OFF OFF OFF OFF ON 172 OFF OFF ON ON OFF ON OFF ON 133 ON OFF ON OFF OFF OFF OFF ON 173 ON OFF ON ON OFF ON OFF ON 134 OFF ON ON OFF OFF OFF OFF ON 174 OFF ON ON ON OFF ON OFF ON 135 ON ON ON OFF OFF OFF OFF ON 175 ON ON ON ON OFF ON OFF ON 136 OFF OFF OFF ON OFF OFF OFF ON 176 OFF OFF OFF OFF ON ON OFF ON 137 ON OFF OFF ON OFF OFF OFF ON 177 ON OFF OFF OFF ON ON OFF ON 138 OFF ON OFF ON OFF OFF OFF ON 178 OFF ON OFF OFF ON ON OFF ON 139 ON ON OFF ON OFF OFF OFF ON 179 ON ON OFF OFF ON ON OFF ON 140 OFF OFF ON ON OFF OFF OFF ON 180 OFF OFF ON OFF ON ON OFF ON 141 ON OFF ON ON OFF OFF OFF ON 181 ON OFF ON OFF ON ON OFF ON 142 OFF ON ON ON OFF OFF OFF ON 182 OFF ON ON OFF ON ON OFF ON 143 ON ON ON ON OFF OFF OFF ON 183 ON ON ON OFF ON ON OFF ON 144 OFF OFF OFF OFF ON OFF OFF ON 184 OFF OFF OFF ON ON ON OFF ON 145 ON OFF OFF OFF ON OFF OFF ON 185 ON OFF OFF ON ON ON OFF ON 146 OFF ON OFF OFF ON OFF OFF ON 186 OFF ON OFF ON ON ON OFF ON 147 ON ON OFF OFF ON OFF OFF ON 187 ON ON OFF ON ON ON OFF ON 148 OFF OFF ON OFF ON OFF OFF ON 188 OFF OFF ON ON ON ON OFF ON 149 ON OFF ON OFF ON OFF OFF ON 189 ON OFF ON ON ON ON OFF ON 150 OFF ON ON OFF ON OFF OFF ON 190 OFF ON ON ON ON ON OFF ON C3417M-B (11/06) SWITCH SETTING SPECTRA ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 SWITCH SETTING SPECTRA ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 191 ON ON ON ON ON ON OFF ON 223 ON ON ON ON ON OFF ON 192 OFF OFF OFF OFF OFF OFF ON ON 224 OFF OFF OFF OFF OFF ON ON ON ON 193 ON OFF OFF OFF OFF OFF ON ON 225 ON OFF OFF OFF OFF ON ON ON 194 OFF ON OFF OFF OFF OFF ON ON 226 OFF ON OFF OFF OFF ON ON ON 195 ON ON OFF OFF OFF OFF ON ON 227 ON ON OFF OFF OFF ON ON ON ON 196 OFF OFF ON OFF OFF OFF ON ON 228 OFF OFF ON OFF OFF ON ON 197 ON OFF ON OFF OFF OFF ON ON 229 ON OFF ON OFF OFF ON ON ON 198 OFF ON ON OFF OFF OFF ON ON 230 OFF ON ON OFF OFF ON ON ON ON 199 ON ON ON OFF OFF OFF ON ON 231 ON ON ON OFF OFF ON ON 200 OFF OFF OFF ON OFF OFF ON ON 232 OFF OFF OFF ON OFF ON ON ON 201 ON OFF OFF ON OFF OFF ON ON 233 ON OFF OFF ON OFF ON ON ON 202 OFF ON OFF ON OFF OFF ON ON 234 OFF ON OFF ON OFF ON ON ON 203 ON ON OFF ON OFF OFF ON ON 235 ON ON OFF ON OFF ON ON ON 204 OFF OFF ON ON OFF OFF ON ON 236 OFF OFF ON ON OFF ON ON ON 205 ON OFF ON ON OFF OFF ON ON 237 ON OFF ON ON OFF ON ON ON 206 OFF ON ON ON OFF OFF ON ON 238 OFF ON ON ON OFF ON ON ON 207 ON ON ON ON OFF OFF ON ON 239 ON ON ON ON OFF ON ON ON ON 208 OFF OFF OFF OFF ON OFF ON ON 240 OFF OFF OFF OFF ON ON ON 209 ON OFF OFF OFF ON OFF ON ON 241 ON OFF OFF OFF ON ON ON ON 210 OFF ON OFF OFF ON OFF ON ON 242 OFF ON OFF OFF ON ON ON ON ON 211 ON ON OFF OFF ON OFF ON ON 243 ON ON OFF OFF ON ON ON 212 OFF OFF ON OFF ON OFF ON ON 244 OFF OFF ON OFF ON ON ON ON 213 ON OFF ON OFF ON OFF ON ON 245 ON OFF ON OFF ON ON ON ON 214 OFF ON ON OFF ON OFF ON ON 246 OFF ON ON OFF ON ON ON ON 215 ON ON ON OFF ON OFF ON ON 247 ON ON ON OFF ON ON ON ON 216 OFF OFF OFF ON ON OFF ON ON 248 OFF OFF OFF ON ON ON ON ON 217 ON OFF OFF ON ON OFF ON ON 249 ON OFF OFF ON ON ON ON ON 218 OFF ON OFF ON ON OFF ON ON 250 OFF ON OFF ON ON ON ON ON 219 ON ON OFF ON ON OFF ON ON 251 ON ON OFF ON ON ON ON ON ON 220 OFF OFF ON ON ON OFF ON ON 252 OFF OFF ON ON ON ON ON 221 ON OFF ON ON ON OFF ON ON 253 ON OFF ON ON ON ON ON ON 222 OFF ON ON ON ON OFF ON ON 254 OFF ON ON ON ON ON ON ON C3417M-B (11/06) 13 Specifications GENERAL ELECTRICAL (Dome Drive Only) Construction Back Box Dome Drive Lower Dome Cable Entry (Back Box) Pan Movement Vertical Tilt Manual Pan/Tilt Speeds* Pan Input Voltage Tilt Preset Speeds Pan Tilt Environment In-Ceiling Environmental In-Ceiling Operating Temperature In-Ceiling Indoor Environmental In-Ceiling Maximum Minimum Weight (approximate) Back Box In-Ceiling Indoor Environmental In-Ceiling Dome Drive Lower Dome In-Ceiling Indoor Environmental In-Ceiling Plastic Aluminum, thermoplastic Acrylic 0.75-inch conduit fitting 360° continuous pan rotation Unobstructed +2° to -92° 0.1°- 80°/sec manual operation, 150°/sec turbo 0.1°- 40°/sec manual operation 400°/sec 200°/sec Indoor Outdoor 18-32 VAC; 24 VAC nominal 22-27 VDC; 24 VDC nominal Input Power 24 VAC 24 VDC Fuse Auxiliary Outputs Alarm Inputs Relay Contacts Type Voltage Current 23 VA nominal (indoor, without heater) 73 VA nominal (outdoor, with heater) 0.7 A nominal (indoor, without heater) 3 A nominal (outdoor, without heater) 1.25 A 2 (Spectra IV SE only) 7 (Spectra IV SE only) AUX 2 Output AUX 1 Form C Open collector transistor output Low voltage (<40 V) 32 VDC maximum 2 A maximum 150 mA maximum Environmental In-Ceiling In-Ceiling 7.5 (19.0) 9.9 (25.2) 32° to 122°F (0° to 50°C) (Assumes no wind chill factor) 140°F (60°C) absolute maximum; 122°F (50°C) sustained maximum -60°F (-51.1°C) absolute minimum; prevents icing at sustained minimum of -50°F (-45°C); de-ices 0.1 inch (2.5 mm) within 3 hours after power-up 1.5 lb (0.68 kg) 2.1 lb (0.95 kg) 3.3 lb (1.48 kg) 0.2 lb (0.09 kg) 0.6 lb (0.27 kg) 4.4 (11.0) 5.2 (13.2) 4.3 (10.9) 3.5 (8.8) 5.9 (15.0) 8.9 (22.6) 5.9 (15.0) 8.2 (20.8) NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES. *For variable-speed operation an appropriate controller is required. With fixed-speed controllers, pan/tilt speed is 20°/sec. The CM6700/CM6800 controller with the KBD200A keyboard has programmable fixed speeds. The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC. This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment. 14 C3417M-B (11/06) PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. If a warranty repair is required, the Dealer must contact Pelco at (800)þ289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information: Exceptions to this warranty are as noted below: 1. Model and serial number 2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number 3. Details of the defect or problem • Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted pair transmission products. • Three years on Spectra® IV products. • Three years on Genex® Series products (multiplexers, server, and keyboard). • Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a five-year warranty. • Three years on PMCL200/300/400 Series LCD monitors. • Two years on standard motorized or fixed focal length lenses. • Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/ DF8 Series fixed dome products. • Two years on Spectra III™, Esprit®, ExSite™, and PS20 scanners, including when used in continuous motion applications. • Two years on Esprit and WW5700 Series window wiper (excluding wiper blades). • Two years (except lamp and color wheel) on Digital Light Processing (DLP®) displays. The lamp and color wheel will be covered for a period of 90 days. The air filter is not covered under warranty. • Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura™ Series distributed network-based video products. • One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months. • Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes). Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty. Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise. The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state to state. If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written explanation with the product when returned. Method of return shipment shall be the same or equal to the method by which the item was received by Pelco. RETURNS In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair). All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge. Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below. If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to: Service Department Pelco 3500 Pelco Way Clovis, CA 93612-5699 If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the following: If the goods are to be sent by a COURIER SERVICE, send the goods to: Pelco 3500 Pelco Way Clovis, CA 93612-5699 USA If the goods are to be sent by a FREIGHT FORWARDER, send the goods to: Pelco c/o Expeditors 473 Eccles Avenue South San Francisco, CA 94080 USA Phone: 650-737-1700 Fax: 650-737-0933 REVISION HISTORY Manual # C3417M C3417M-A C3417M-B Date 8/06 9/06 11/06 Comments Original version. Corrected illustration 7. Inserted compatibility table. Added serial port settings to Table E. Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura, ExSite, and Spectra III are trademarks of Pelco. DLP is a registered trademark of Texas Instruments, Inc. ©Copyright 2006, Pelco. All rights reserved. Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO9001 Australia | Canada | Finland | France | Italy | Russia | Singapore | Spain | Sweden | The Netherlands | United Arab Emirates | United Kingdom | United States
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Mode : UseNone XMP Toolkit : 3.1-702 Producer : Acrobat Distiller 7.0.5 (Windows) Keywords : Camera Site Equipment|Camera Systems|Spectra High Speed Domes Creator Tool : FrameMaker 7.1 Modify Date : 2006:11:28 15:34:57-08:00 Create Date : 2006:11:16 14:29:36Z Metadata Date : 2006:11:28 15:34:57-08:00 Format : application/pdf Title : Pelco_Spectra_IV_in_Ceilings_Back_Box_manual Creator : . Subject : Camera Site Equipment|Camera Systems|Spectra High Speed Domes Description : C3417MB Document ID : uuid:b8d1d5fc-56c1-4e03-b55f-36edd673b5bd Instance ID : uuid:6a8d6bea-fc50-4b08-82f8-e71c4f0070e5 Page Count : 16 Warning : [Minor] Ignored duplicate Info dictionaryEXIF Metadata provided by EXIF.tools