Pelco Security Camera Ed29 Users Manual ED28_ED2820 And ED29_ED2920 Harris Dome Enclosures_manual
ED29ED2920 to the manual 2dcea367-3611-444e-8dbb-6ff67386162a
2015-02-02
: Pelco Pelco-Pelco-Security-Camera-Ed29-Users-Manual-441403 pelco-pelco-security-camera-ed29-users-manual-441403 pelco pdf
Open the PDF directly: View PDF .
Page Count: 36
Download | ![]() |
Open PDF In Browser | View PDF |
® ED28/ED2820 and ED29/ED2920 “Harris Dome” Enclosures Installation/Operation Manual C460M-E (7/95) PELCO • 3500 Pelco Way • Clovis, CA 93612-5699 • USA • www.pelco.com (800) 289-9100 or (1-559) 292-1981 • FAX (800) 289-9150 or (1-559) 292-3827 PELCO Manual C460M-E (7/95) 33 TABLE OF CONTENTS Section Page 1.0 WARNINGS ........................................................................................................................................ 1 2.0 SCOPE ............................................................................................................................................... 2 3.0 DESCRIPTION ................................................................................................................................... 2 4.0 INSTALLATION ................................................................................................................................... 3 4.1 UNPACKING INSTRUCTIONS ................................................................................................... 3 4.2 CONDUCTOR REQUIREMENTS .............................................................................................. 3 4.3 WIRING INSTRUCTIONS .......................................................................................................... 4 4.4 INSTALLATION INSTRUCTIONS ............................................................................................... 7 4.4.1 Mounting the ED28/ ED2820 Series ............................................................................... 8 4.4.1.1 Wall Mounting .................................................................................................... 8 4.4.1.2 Corner Mounting ................................................................................................ 9 4.4.1.3 EDM210 Mounting Extension .......................................................................... 11 4.4.1.4 Parapet or Pole Mounting ................................................................................. 12 4.4.2 Mounting the ED29/ ED2920 Series ............................................................................. 13 4.5 LIMIT/STOP ADJUSTMENTS ................................................................................................... 13 5.0 CARE AND MAINTENANCE ............................................................................................................ 13 5.1 RECOMMENDED EQUIPMENT AND TOOLS ......................................................................... 13 5.2 SERVICE TIPS ......................................................................................................................... 13 6.0 ED28 EXPLODED ASSEMBLY DIAGRAM ...................................................................................... 14 7.0 ED28 MECHANICAL PARTS LIST ................................................................................................... 15 8.0 INSTALLATION ................................................................................................................................. 16 8.1 WIRING .................................................................................................................................... 16 8.2 CONDUCTOR AND CABLE REQUIREMENTS ....................................................................... 16 8.3 CONNECTOR ASSEMBLY ...................................................................................................... 17 8.4 LIMIT/STOP ADJUSTMENTS .................................................................................................. 21 9.0 OPERATIONAL TEST ...................................................................................................................... 21 9.1 CONTROL ................................................................................................................................ 21 9.2 AUTO/RANDOM SCAN OPERATION ...................................................................................... 22 10.0 MAINTENANCE ............................................................................................................................... 22 10.1 RECOMMENDED EQUIPMENT .............................................................................................. 22 10.2 SERVICE TIPS ......................................................................................................................... 22 11.0 EXPLODED ASSEMBLY DIAGRAM (PT2801000ASSY) ................................................................. 23 11.1 EXPLODED HARDWARE DIAGRAM (MODEL PT2801000ASSY) ......................................... 24 12.0 MECHANICAL PARTS LIST PT2801002ASSY/PT2801003ASSY .................................................. 25 12.1 MECHANICAL HARDWARE LIST (PT2801000ASSY ............................................................. 26 13.0 ENCLOSURE MODELS ................................................................................................................... 27 13.1 OPTIONS ................................................................................................................................. 27 ii PELCO Manual C460M-E (7/95) 14.0 ENCLOSURE SPECIFICATIONS .................................................................................................... 28 15.0 PAN/TILT ASSEMBLIES ................................................................................................................... 29 15.1 ASSEMBLY DESCRIPTION ..................................................................................................... 29 16.0 ASSEMBLY SPECIFICATIONS ........................................................................................................ 29 16.1 ASSEMBLY MODELS .............................................................................................................. 29 17.0 PAN/TILT ASSEMBLY INSTALLATION ............................................................................................ 30 18.0 WARRANTY AND RETURN INFORMATION .................................................................................. 32 LIST OF ILLUSTRATIONS Figure 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Page ED28/ED2820 Dimension Diagram ............................................................................................ 2 ED29/ED2920 Dimension Diagram ............................................................................................ 3 120VAC Heater/Blower Wiring Diagram ..................................................................................... 4 230 VAC Heater/Blower Wiring Diagram .................................................................................... 5 Receiver/Pan and Tilt Wiring Harness (Non-PP) ........................................................................ 6 Receiver/Preset Pan and Tilt With Alarm Output Wiring Diagram .............................................. 6 Coaxitron/Wiretron Power Patch Wiring Schematic ................................................................... 7 Camera/Lens Mounting .............................................................................................................. 8 Wall Mounting ............................................................................................................................. 8 Corner Mounting ........................................................................................................................ 9 Mounting Templates ................................................................................................................. 10 EDM210 Mounting Extension Illustration ................................................................................. 11 ED28/ED2820 Series Parapet or Pole Mount .......................................................................... 12 ED28 Exploded Assembly Diagram ......................................................................................... 14 Connector Assembly ................................................................................................................ 17 PT2801000ASSY/PT2801001ASSY Wiring Diagram .............................................................. 18 PT2801002ASSY Wiring Diagram ........................................................................................... 19 PT2801003ASSY Wiring Diagram ........................................................................................... 20 Limit Stops ................................................................................................................................ 21 Exploded Parts Assembly Diagram (PT2801000ASSY) .......................................................... 23 Exploded Hardware Assembly Diagram (PT2801000ASSY) ................................................... 24 ED28KIT Installation/Exploded View ........................................................................................ 31 Pelco, the Pelco Logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco. PELCO Manual C460M-E (7/95) © Copyright 1995, Pelco. All rights reserved. iii REVISION HISTORY Manual # Date Comments C460M 3/89 Original Version. C460M 6/90 Revision A. Manual separated into two parts: enclosures and pan/tilt. Completely revised to include ED2820RX/PP and ED2820SL-RX/PP models. C460M 11/90 Revision B. Figure 2-4 revised. C460M 6/92 Revision C. Completely revised to include the following models: ED2820-3, ED220-PP, ED2820SL/PP, ED2820WX, ED2820SL-WX, and ED29/ED2920 Series. C460M-D 2/95 Revision D. Parts I and II integrated into one complete manual. Models ED2920-3 added. Figures 3, 4 and 7 revised. New Figure 21 added as per ECO92-216 with installation instructions for ED28KIT. New pan/tilt assembly numbers PT2801000ASSY, PT2801001ASSY, PT2801002ASSY, and PT2801003ASSY incorporated into manual. Incorporated new exploded assembly diagrams and new parts/hardware materials lists. C460M-E 7/95 Revision E. Manual revised to include the addition of newly-created ED29-3 enclosure as per ECO # 95-195. Items 14 and 25 in section 12.0, parts list, revised. 6/96 Corrected part number for item number 51 (Connector, 9position) also relaced Figure 21 (ED28KIT Installation/ Exploded View). 8/96 Revised Section 7.0, ED28 Mechanical Parts List, regarding part numbers for dome. iv PELCO Manual C460M-E (7/95) INSTALLATION/OPERATION MANUAL MODEL ED28, ED2820, ED29, ED2920 SERIES “HARRIS DOME” ENCLOSURES 1.0 WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes. 2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6 or 6P enclosure, it is designed for Indoor use only and it must not be installed where exposed to rain and moisture. 3. The product bears the following marks: 4. Only use replacement parts recommended by PELCO. 5. After replacement/repair of this unit’s electrical components, conduct a resistance measurement between line and exposed parts to verify the exposed parts have not been connected to line circuitry. 7. The weight of the camera/lens should not exceed 15 lbs. This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN. Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. PELCO Manual C460M-E (7/95) 1 2.0 SCOPE The information contained within this manual covers the Harris Environmental Dome. combine concealed 360° surveillance with distortionfree viewing. The black opaque lower dome has a clear viewing slot which effectively camouflages a CCTV security/surveillance system without compromising the quality of the video picture. 3.0 DESCRIPTION This product was developed outside of PELCO’s normal product development process, and outside of normal working hours by Jimmy Harris, Sheet Metal Department Manager. In recognition of this extraordinary effort, PELCO has proudly named this product the Harris Dome. The enclosure has been engineered for ease of installation, serviceability, and relocation. The lower dome quickly and easily swings open with the aid of a gas strut for convenient access to the camera and pan/tilt. The pan/tilt can easily be removed for camera/lens service by loosening two hex head fasteners and disconnecting its cable. PELCO’s Harris Environmental Dome is a discreet outdoor surveillance enclosure designed to be mounted to any solid wall, vertical surface, or parapet, and completely encloses the pan/tilt and camera/lens to Figure 1. ED28/ED2820 Series Dimension Drawing 2 PELCO Manual C460M-E (7/95) 4.0 INSTALLATION 4.1 UNPACKING INSTRUCTIONS The dome and enclosure are shipped in separate cartons. Make sure you have both before installing. Save the shipping cartons and plastic packaging in case any part of the unit has to be returned for credit or repair. ED2820-3SL/PP ED2820SL/PP Twenty (20), plus ground for pan/tilt, lens and camera AC, plus two (2) for heater/blower ED2820-PP Nineteen (19) plus ground for pan/ tilt, lens and camera AC, plus two (2) for heater/blower 4.2 CONDUCTOR REQUIREMENTS ED28 ED29 ED28-1 ED29-1 ED29-3 ED2820-RX ED2820SL-RX Coax cable and 120 VAC power cord See the camera manufacturer’s specifications sheet. Two (2) conductor, plus ground for heater/blower and recommended conductors for camera ED2820-RX/PP ED2820SL-RX/PP Same as ED2820-RX plus 10 conductors for alarms ED2820-WX ED2820SL-WX Twisted pair, coax, and 120 VAC power cord ED2820, ED2820-3 ED2920, ED2920-3 ED2820-SL ED2920-SL Eleven (11) plus ground for pan/tilt, lens and camera AC, plus two (2) for heater/blower Figure 2. ED29/ED2920 Series Dimension Drawing PELCO Manual C460M-E (7/95) 3 4.3 WIRING INSTRUCTIONS Models ED28-1 and ED29-1 nating the need for wiring harnesses made in the field. Wire the control cable per Section 9.3 using the applicable wiring diagrams in Figures 16 through 18, and supply the necessary power. These models are supplied with a factory installed heater/blower and service light. Supply 120 VAC power for the heater/blower and wire according to Figures 3. Models ED2820-RX, ED2820SL-RX, ED2820-RX/PP, ED2820SL-RX/PP, ED2920-RX and ED2920SL-RX Models ED2820-3, ED2820-3SL/PP, ED2920-3, ED29-3 When wiring the dome models with integral Coaxitron receiver listed above, connect the coax to the controller and plug the receiver into a 120 VAC power supply. These models are supplied with factory-installed blower/ heater and service light. For installation, supply 230 VAC power for the blower/heater and wire according to the diagram in Figure 4. Models ED2820, ED2820-3, ED2820-SL, ED2820-PP, ED2820SL/PP, ED2820-3SL/ PP, ED2920, and ED2920-SL These Harris Dome models without receiver include the PT2801000ASSY,PT2801001ASSY, PT2801002ASSY or PT2801003ASSY pan/tilt assemblies which are prewired for all control functions — pan/tilt, motorized zoom lens, camera power (24 VAC) and video. All connections are made at the input connector, elimi- In addition, the ED2820-RX/PP and ED2820SL-RX/ PP include preset position feedback capabilities. These packages are equipped with PT2801002ASSY and PT2801003ASSY pan/tilts and have the Coaxitron receiver installed and pre-wired to the pan/tilt. Since these versions include 8 alarm inputs and 1 alarm output, be sure to wire them according to the diagram in Figure 6. Models ED2820-WX and ED2820SL-WX To wire Harris Dome models ED2820-WX and ED2820SL-WX with integral Wiretron receiver, connect the twisted pair and coax to the controller and plug the receiver into a 120 VAC power supply. Figure 3. Heater/Blower Wiring Diagram (120 VAC) 4 PELCO Manual C460M-E (7/95) Figure 4. Heater/Blower Wiring Diagram (230 VAC) Wiring Pin Assignments Figure 3 Number 1 2 3 4 5 6 7 8 9 10 Function Number 11 12 13 14 15 16 17 18 19 20 Iris Zoom Focus Lens Common Manual Iris Not Used Camera On AC Input High AC Input Neutral Ground Function Not Used Not Used Heater #2 Heater #2 Not Used Heater #1 Heater #1 AC High AC Neutral Ground Number 21 22 23 24 25 26 27 28 29 30 Function Fan Not Used Not Used Fan Not Used Not Used Not Used Connected to #6 Not Used Camera Wiring Pin Assignments Figure 4 Number 1 2 3 4 5 6 7 8 9 10 Function Iris Zoom Focus Lens Common Manual Iris Not Used Camera On AC Input High AC Input Neutral Ground PELCO Manual C460M-E (7/95) Number 11 12 13 14 15 16 17 18 19 20 Function Not Used Not Used Heater #2 Not Used Connect Heaters 1 & 2 Not Used Heater #1 AC High AC Neutral Ground Number 21 22 23 24 25 26 27 28 29 30 Function Fan Not Used Not Used Fan Not Used Not Used Not Used Connected to #6 Not Used Camera 5 Figure 5. Receiver/Pan and Tilt Wiring Harness (Non-PP) 1 2 3 4 5 6 7 8 9 10 10 CONDUCTOR CABLE, 3 FEET OPEN WIRES OUTSIDE DOME CONA28S BROWN RED ORANGE YELLOW GREEN BLUE VIOLET GREY WHITE BLACK ALARM INPUT #1 ALARM INPUT #2 ALARM INPUT #3 ALARM INPUT #4 ALARM INPUT #5 ALARM INPUT #6 ALARM INPUT #7 ALARM INPUT #8 ALARM OUTPUT ALARM COMMON 10 POS MTA CONN (CON1-640428-0) WIRE AT 12 INCHES ZS-SPIROBAND POS. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 17 18 19 20 23 24 25 28 POS CONNECTOR COLOR DESC. BROWN WHT/VIO RED WHT/BLK YELLOW ORANGE BLUE GREEN WHITE BLACK WHT/BRN WHT/RED WHT/ORG WHT/YEL WHT/BLU GRY/WHT VIO/WHT BLK/WHT ORG/WHT YEL/WHT GRN/WHT P/T COMMON VIDEO CORE LEFT VIDEO SHIELD DOWN UP RIGHT GROUND CAMERA AC HIGH IRIS FOCUS ZOOM LENS COMMEN CAMERA AC LOW PRESET COMMEN PRESET HIGH PAN PRESET B TILT PRESET LENS ZOOM PRESET LENS FOCUS PRESET PAN PRESET A 1 2 3 4 5 9 10 GRN/WHT BLK/WHT ORG/WTH YEL/WHT VIO/WHT WHT/BLU GRY/WHT PAN PRESET A TILT PRESET LENS ZOOM PRESET LENS FOCUS PRESET PAN PRESET B PRESET HIGH PRESET COMMON 10 POS MTA CONN (CON-640428-0) TO RECEIVER PP BOARD 1 WHT/VIO 2 WHT/BLK 1 2 3 4 5 6 7 8 9 10 11 12 13 14 WHITE WHT/YEL BROWN RED BLUE YELLOW ORANGE 14 POS MTA PLUG (CON1-640428-4) TO RECEIVER MOTHER BOARD GREEN WHT/RED WHT/BRN BLACK WHT/ORG 2 POS RECEPTACLE (CON1-480318-0) Figure 6. Receiver/Preset Pan and Tilt With Alarm Output Wiring Diagram 6 PELCO Manual C460M-E (7/95) Figure 7. Coaxitron/Wiretron Power Patch (CX9024RX/WX8024RX) Wiring Schematic 4.4 INSTALLATION INSTRUCTIONS The Harris Dome is supplied in three (3) configurations: as a passive dome (for use as a dummy dome or with a fixed camera ), with a factory installed pan/tilt, or with a factory installed pan/tilt and receiver/driver. CAUTION: Make certain that the mounting surface is capable of supporting the full load of the mount, pan/tilt, camera/lens, and enclosure. When the pan/tilt is removed, mount the camera/lens (see Figure 8) and make the electrical connections to the pan/tilt (camera power, video, lens). When closing the dome, be sure the drive tab on the dome engages the slot on the drive arm of the pan/tilt. WARNING: Do not rotate pan/tilt by hand. Rotate by controller only. Handle the lower dome with care so as not to scratch or get fingerprints on the viewing window. When installing a dome with an integral pan/tilt, loosen the two (2) fasteners and remove the pan/tilt to reduce the total weight of the unit. PELCO Manual C460M-E (7/95) 7 NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES. Figure 8. Camera/Lens Mounting 4.4.1 Mounting the ED28/ED2820 Series 4.4.1.1 Wall Mounting The ED28/ED2820 series may be mounted directly to a wall or vertical surface. To attach the enclosure to a vertical surface, perform the following (see Figure 9): 1. Using the enclosure or the template supplied (see Figure 12), mark the location of the four (4) mounting holes. If the control and power cables are to pass through the mounting surface, mark the large center hole as well. 2. Drill four (4) mounting holes according to the fasteners being used (minimum 5/16-inch diameter, not supplied). 3. Mount the enclosure to the surface using the required fasteners. If needed, route the control cables through the mounting structure. 4. Install pan/tilt with camera/lens. Figure 9. Wall Mounting 8 PELCO Manual C460M-E (7/95) 4.4.1.2 Corner Mounting The ED28/ED2820 series may be mounted to the outside corner of a structure using the CM100 Corner Mount Adapter. To attach the enclosure to an outside corner, perform the following steps (see Figure 10): 1. Secure the CM100 corner mount adapter as stated in the installation manual provided with the mount. 2. Mount the enclosure to the CM100 using four (4) 1/4-inch diameter fasteners. 3. Route the power cord and control cables through the hole in the mount arm and make the necessary connections. 4. Install the pan/tilt with the camera/lens mounted. Figure 10. Corner Mounting PELCO Manual C460M-E (7/95) 9 ED28/ED2820 SERIES AND EDM210 HOLE PATTERN ST1 HOLE PATTERN Figure 11. Mounting Templates 10 PELCO Manual C460M-E (7/95) 4.4.1.3 EDM210 Mounting Extension 2. When needed, the ED28/ED2820 series dome may be mounted 10 inches (25.4 cm) farther from the mounting surface with the use of the EDM210 mounting extension. It should be noted that in areas with heavy snowfall or high winds, the ST1 support strut should also be used. Drill the mounting holes according to the fasteners being used (minimum 5/16-inch diameter, not supplied, quantity 4). 3. Mount the enclosure to the EDM210 with the required fasteners. Route the cables through the extension. 4. Mount the enclosure/extension to the mounting surface using the required fasteners. If needed, route the control cables through the mounting structure. 5. Install the pan/tilt with camera/lens. To attach the enclosure to a vertical surface and incorporate the EDM210, perform the following steps (see Figure 12): 1. Using the enclosure, EDM210, or the template supplied (see Figure 11), mark the location of the four (4) mounting holes. If the control and power cables are to pass through the mounting surface, mark the large center hole as well. Figure 12. EDM210 Mounting Extension Installation PELCO Manual C460M-E (7/95) 11 4.4.1.4 Parapet or Pole Mounting When mounting to a parapet, use of the PP200/PPI200 parapet mount or PP300/PP301 parapet corner mounts is recommended. The ED28/ED2820 series dome may be mounted to other standard PELCO mounts, including the PP100 Parapet Mount or the PA102 Pole Mount. These mounts can be used in conjunction with the EDM210 mount extension and the ST1 strut. (See Figure 12.) Follow the mounting instructions enclosed with the appropriate mount and then proceed as stated in Section 4.4.1.2, step 3 or Section 4.4.1.3, step 3, as required. PP200/PPI200 PP300/PP301 with PPI200 PP100 PA102 Figure 13. ED28/ED2820 Series Parapet or Pole Mounting 12 PELCO Manual C460M-E (7/95) 4.4.2 Mounting the ED29/ED2920 Series 5.2 SERVICE TIPS The ED29/ED2920 Series domes require a suitable length of 1-1/2-inch NPT threaded pipe (not supplied) for mounting. The dome can be attached to any wall or ceiling capable of supporting the full weight of the mount, pan/tilt, camera/lens, and enclosure. We suggest using the MRWA wall mount or MRCA ceiling mount. Follow the instructions provided with the mount. Some common problems encountered with pan/tilt systems include miswiring, overloading, and not using the units for the correct applications. If a failure occurs, it is recommended that the following procedures be used. 1. If the pan/tilt ceases to operate, turn the control unit off and remove the AC cord from the outlet. 4.5 LIMIT/STOP ADJUSTMENTS 2. Check the fuse in the control unit using either a voltmeter or ohmmeter. If open (blown), replace with the proper recommended fuse. 3. Replace the AC cord in the outlet and turn the control on. If the fuse continues to open (blow), turn the unit off. 4. Check the control cable between the control unit and pan/tilt for shorts, high resistance, or opens. 5. If the control cable is found to be good, replace the connector to the control unit, leave the connector off the pan/tilt, and replace the fuse. 6. Operate the control unit when it is disconnected from the pan/tilt. If the fuse continues to “blow” the fault is in the control. Refer to the appropriate service manual for the control being used. 7. Check the wiring harness in the pan/tilt for shorts. 8. If the wiring harness is found to be good, then the problem is internal to the unit; consult factory. To adjust the pan/tilt limits, refer to Section 8.4, of this manual. 5.0 CARE AND MAINTENANCE Regularly scheduled maintenance will prolong the operational life and appearance of the equipment. IMPORTANT: The lower dome of the Harris Dome is an optical surface. When cleaning the inner surface of the dome and viewing window, treat as carefully as you would a fine camera lens. 1. If dust or other debris accumulates on the inside of the lower dome, remove them with clean air pressure. Compressed air cans are available from commercial photographic equipment and supply dealers. WARNING: Do not use water, liquid or spray cleaners of any kind on coated innersurface of dome. 2. Clean the outer surface of the dome and the inner surface of the viewing window with a nonabrasive cleaning cloth and antistatic cleaner that is safe for use on acrylic plastic. Do not use kerosene or similar substances that can scratch the surface. 5.1 RECOMMENDED EQUIPMENT AND TOOLS 1. 2. 3. 4. 5. Voltmeter or Ohmmeter Allen Wrench Set Wrench Set Flat Blade and Phillips Head Screw Drivers Pliers, Long Nose PELCO Manual C460M-E (7/95) 13 6.0 ED28 EXPLODED ASSEMBLY DIAGRAM Figure 14. ED28 Exploded Assembly Diagram 14 PELCO Manual C460M-E (7/95) 7.0 ED28 MECHANICAL PARTS LIST The following parts list corresponds to the exploded assembly diagram in Figure 14. Item Qty 1 2 3 4 5 6 7 8 9 10 11 12 2 2 2 1 1 1 1 1 1 1 6 1 1 4 8 4 1 4 2 1 4 4 2 2 1 4 13 14 15 16 17 18 19 20 21 22 23 24 25 Description Fastener Receptacle Retainer Holder, Lamp (not shown) Back Box Assy Plate, Front Bracket, Cylinder Bracket, Switch, Service Light Dome, Clear 20" Cylinder gas spring, 20# NP Gasket, Poron Lamp, C-7, 120 VAC (not shown) Lamp, S-6, 230VAC (not shown) Gasket, Filter Foam (not shown) Bushing Spacer, .250 OD x .375" Dome Drive Tab Roller, Delrin, Black Spacer, 5/16 OD x .375" Switch Cable Tie, 2" (not shown) Mount, Cable Tie (not shown) Nut, Wing,1/4-20 (not shown) Nut, Acorn (not shown) Washer, #5610-22-60 (not shown) Roller O-ring (not shown) Part Number ED210000 ED210001 ED210002 ED210020 ED28001001WA ED28004003COMP ED28004011COMP ED28004031COMP ED282006* EH550010020 EH550010033 LAP7C7 LAP10S6/10 ED210006 SB310005 SB310007 SB34006COMP SB34020COMP SPA8542 SWIV3L WIRCABLETIE2 WIRCABLETIEMT-2 ZH1/4-20NUTSW ZH10-32NUTCA ZH200X437X62N ED210100** * Part number is for the dome only. To order the complete dome assembly, specify the part number ED28DOMECLP, which includes items 9 and 16. ** O-ring is not used with domes that have a flange diameter of 21.32 inches ± .030 inches. PELCO Manual C460M-E (7/95) 15 8.0 INSTALLATION In order to ensure proper wiring and system operation of all components, it is highly recommended that the pan/ tilt and the associated control equipment be tested in your facility before field installation is attempted. Assemble the mating connector as outlined in Figure 15 and wire the control cable according to the applicable diagrams provided in Figures 16 through 17 for all models except ED28, ED28-1, ED29, ED29-1 and models with integral receiver (RX or WX). Models with integral receiver are pre-wired at the factory. (Standard pan/tilt with presets) PT2801002ASSY: Pan/Tilt (9 plus ground) Lens (8) Camera AC (2) (SL pan/tilt with presets) PT2801003ASSY: Pan/Tilt (10 plus ground) Lens (8) Camera AC (2) Cable Distances — Hard-Wire Controls Pan/Tilt Functions 8.1 WIRING When using a Coaxitron or Wiretron Control System, consider using the C1906 and C1925 factory assembled pretested cables which are wired for inverted applications. 20 Awg 18 Awg 16 Awg 5 Conductors 110 feet (33.5 m) 180 feet (54.8 m) 290 feet (88.3 m) 6 Conductors* 210 feet (64 m) 330 feet (100 m) 530 feet (161 m) *Using 2 conductor common NOTE: If you are not using the C1906 or C1925 pretested cables, you must reverse the left/right and up/down function pins shown in Figures 16 through Figure 18. Cable distances should not exceed the distances specified in Section 8.2, Conductor/Cable Requirements. Cable fabrication must be in accordance with Figure 15. The following are some recommended common installation practices. Camera Power Consult the camera manufacturer for transformer power distances. NOTE: A relay box (RB24) is available to extend the operating distance (control to relay box) up to 13,000 feet (3,962 m) utilizing 16 Awg wire. Cable Distances — Coaxitron 1. Always use jacketed stranded multiconductor interconnecting cable between the control and the pan/tilt unit, with additional conductors than needed for future servicing and or additions. 2. Always use color-coded conductors for ease of wiring and to identify functions at a later date. 3. Keep a wiring diagram with the system for later use and reference. 8.2 CONDUCTOR AND CABLE REQUIREMENTS Conductors Up to a maximum of 750 feet (228 m) on a single coax (RG59/U) from the receiver to the transmitter. NOTE: To extend the distance to 3,000 feet (914m) on RG59/U coax, use the PELCO EA2000 Half Duplex Equalizing Amplifier. Cable Distances — Wiretron Maximum recommended distances from the receiver to the transmitter using twisted pair, unshielded cable are as follows: 22 Awg 20 Awg 5 miles (8 km) 10 miles (16 km) Conductor requirements are as listed, plus coax cable. (Standard or SL pan/tilt) PT2801000ASSY PT2801001ASSY: Pan/Tilt (5 plus ground) Lens (4) Camera AC (2) 16 PELCO Manual C460M-E (7/95) 8.3 CONNECTOR ASSEMBLY Installation and/or testing will require you to assemble the connector parts provided. Fabricate the interconnecting cable according to the following steps (reference Figure 15). 1. Slide part A of the cable clamp (item 1) over the end of the cable (item 1, part C) with the threaded end of the cable clamp facing the connector (item 5). 2. If the cable has a diameter less than 1/2 inch (1.3 cm), slide the rubber boot (item 2) over the end of the cable and pull through the cable clamp to so that the boot encases the cable and forms a good seal. 3. Strip back the cable jacket approximately 11/4 inches (3.2 cm) and separate the individual conductors (item 3). 4. The contact pins supplied with the mating connector are the “crimp” type which may also be soldered if you so desired (item 4). 5. After crimping or soldering the contact pins to the conductors, push them into the proper holes in the connector until they snap in place. NOTE: Contacts cannot be removed from the connector without the use of the appropriate AMP extraction tool which is available from PELCO. 6. Slide part A of the cable clamp toward the connector and screw the parts together. Attach part B (item 1) onto part A and connect both parts with the screws provided. 7. Connect the cable assembly to the unit and seat the connector by twisting the locking collar until it snaps into position. Refer to Figures 16-18 for the appropriate wiring diagram. 5 1 threaded end of cable clamp A B C STEP 1 5 1 FLEXIBLE RUBBER BOOT A B STEP 2 C 2 5 ** 3 4 1 A STRIP 1/8" B C STEPS 3-7 CRIMP INSULATION CRIMP WIRE OUTSIDE JACKET OF CABLE STRIP 1" ** ITEM 5 DETAIL 4 1 9 10 2 1 3 5 15 4 8 16 22 28 23 33 29 37 34 15 20 25 21 28 3 3 10 1 7 14 26 FRONT VIEW 28-PIN CONNECTOR FRONT VIEW 37-PIN CONNECTOR 11 16 15 FRONT VIEW 16-PIN CONNECTOR 3 1 4 7 4 6 THE MOST COMMONLY USED CONNECTOR PIN-OUT CONFIGURATIONS ARE SHOWN HERE. REFERENCE THE CONNECTOR DRAWING APPLICABLE TO YOUR SITUATION. 1 6 9 14 11 8 14 9 7 12 FRONT VIEW 14-PIN CONNECTOR FRONT VIEW 9-PIN CONNECTOR Figure 15. Connector Assembly PELCO Manual C460M-E (7/95) 17 QTY 2 1 1 1 14 4 1 1 1 1 SYMBOL C1,C2 M1 M2 J2 — S1-S4 — — — — Note: DESCRIPTION CAPACITOR,15 MFD,100V PAN MOTOR TILT MOTOR CONNECTOR CONNECTOR PINS SWITCH INPUT CONNECTOR MATING CONNECTOR ASSY ACTUATOR LENS MATING CONNECTOR MANUFACTURER PART NUMBER SPRAGUE PELCO PELCO HIRSCHMANN AMP MICROSWITCH AMP AMP MICROSWITCH HIRSCHMANN CAPU0015.0/100N 2508001 PS78001 CONMAB6100 CON66102-7 SWI1SM1 CON206044-1 CONA14S SWIJS138B CONMAS6100 For non-receiver models only, you must reverse the left/right and up/down function pins shown above if you are not using the C1906 or C1925 pretested cables. Figure 16. PT2801000ASSY/PT2801001ASSY Wiring Diagram (Standard or SL Models) 18 PELCO Manual C460M-E (7/95) Note: For non-receiver models only, you must reverse the left/right and up/down function pins shown above if you are not using the C1906/PP or C1925/PP pretested cables. Figure 17. PT2801002ASSY Wiring Diagram (Standard with Presets) PELCO Manual C460M-E (7/95) 19 Note: For non-receiver models only, you must reverse the left/right and up/down function pins shown above if you are not using the C1906/PP or C1925/PP pretested cables. Figure 18. PT2801003ASSY Wiring Diagram (SL with Presets) 20 PELCO Manual C460M-E (7/95) 8.4 LIMIT/STOP ADJUSTMENTS WARNING: Do not operate pan/tilt without limit stops. Do not remove or reposition the fixed actuator on the non-SL. DAMAGE WILL OCCUR. NOTE: SL models are not equipped with pan limit stops. (Disregard steps 1-5 below). To set limit stops, perform the following steps (refer to Figure 19). 1. Loosen the pan limit stops. 2. Turn the control unit “on.” Pan the unit to the right until the desired right pan limit is reached. 3. Move the right pan limit stop until it touches the pan limit switch actuator. Move the stop a slight distance further against the actuator until it “clicks”, indicating opening of the limit switch. Lock the stop in place. 4. Pan the unit to the desired “left” position. Adjust the left pan limit stop as described in step 3. 5. Pan left and right to both limit stops and check for exact positioning. Tighten both stops securely. Figure 19. Limit Stops the installation cable at the job site. Splice the ends, color-to-color, onto the cable in the field, using the terminal blocks at each end. 9.0 OPERATIONAL TEST 6. Remove the end cup from the left side of the tilt table. Loosen the tilt limit stop screws and tilt the table, using the joystick, to the desired “up” position. 7. Move the “up” limit stop until it touches the tilt limit switch actuator and “clicks”. Lock the stop in place. 8. Tilt the table to the desired “down” position and set the stop in the same manner. 9. Tilt the table up and down and check for exact positioning. Tighten both stops securely. Replace the side cover. After the unit has been tested and stops aligned, turn off the control and disconnect the AC cord from the outlet. Remove the multiconductor cable from both the pan/tilt and control unit. This cable can then be used for installation by cutting the test cable and splicing the ends onto PELCO Manual C460M-E (7/95) 9.1 CONTROL Connect the cable assembly between the pan/tilt and the control unit. Plug the control unit into the AC outlet and switch the unit on. Move the joystick to the UP position. Observing the “Front” label on the pan/tilt, the front of the tilt table should move up. Move the joystick to the DOWN position, and the front of the tilt table should move down. Releasing the joystick should allow it to return to center and the tilt table should immediately stop moving. Move the joystick to the LEFT position and the complete top assembly should rotate counterclockwise. With the joystick moved to the RIGHT position, the unit will rotate clockwise. Both the pan and tilt motors are protected from mechanical over-travel by electrical limits which stop the motors. 21 9.2 AUTO/RANDOM SCAN OPERATION 10.2 SERVICE TIPS The pan/tilt will function in the Auto/Random mode with the addition of the appropriate PELCO control system. The pan/tilt has no additional limit switches or relays for auto scan operation and is, therefore, only compatible with current sensing auto/random type circuits employed in our control systems. Some common problems encountered with pan/tilt systems include miswiring, overloading, and not using the units for the correct application. Should a failure occur, it is recommended that the following procedures be used. 1. If the pan/tilt ceases to operate, turn the control unit off and remove the AC cord from the outlet. 2. Check the fuse in the control unit using either a voltmeter or ohmmeter. If open (blown), replace with the proper recommended fuse. 3. Replace the AC cord in the outlet and turn the control on. If the fuse continues to open (blow), turn the unit off. 4. Check the control cable between the control unit and pan/tilt for shorts, high resistance, or opens. 5. If the control cable is found to be good, replace the connector to the control unit, leave the connector off the pan/tilt, and replace the fuse. 6. Operate the control unit when it is disconnected from the pan/tilt. If the fuse continues to “blow” the fault is in the control. Refer to the appropriate service manual for the control being used. 7. Check the wiring harness in the pan/tilt for shorts. 8. If the wiring harness is found to be good, then the problem is internal to the unit; consult factory. 10.0 MAINTENANCE 10.1 RECOMMENDED EQUIPMENT AND TOOLS 1. 2. 3. 4. 5. Voltmeter or Ohmmeter Allen Wrench Set Wrench Set Flat Blade and Phillips Head Screwdrivers Pliers, Long Nose Refer to Figures 16 through 18, if necessary. 22 PELCO Manual C460M-E (7/95) 11.0 EXPLODED ASSEMBLY DIAGRAM (Model PT2801000ASSY) Figure 20. Exploded Assembly Parts Diagram (Model PT2801000ASSY) PELCO Manual C460M-E (7/95) 23 11.1 EXPLODED HARDWARE DIAGRAM (Model PT2801000ASSY) Figure 21. Exploded Assembly Hardware Diagram (Model PT2801000ASSY) 24 PELCO Manual C460M-E (7/95) 12.0 MECHANICAL PARTS LIST (PT2801000ASSY) The following parts list corresponds to the exploded assembly diagram in Figure 20. Item Qty 1 4 2 1 1 1 2 1 2 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 1 2 1 1 1 4 2 4 2 1 1 1 1 1 1 1 1 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 PELCO Manual C460M-E (7/95) Description Ring, Snap #Q2-18 Ring, Snap #Q2-18 (SL) Pin, Pan Limit (Non-SL) Pin, Pan Limit (P/PP Only) Pin, Tilt Limit Tilt Limit Stop Bracket, Tilt Limit Cover Plate, Tilt Pin, #1 X 1-1/4 Taper Nut, Spindle Clamp, Cable (SL Only) Spacer, Tilt Collar Bearing, Pan Spindle Bearing, Tilt FB68-31/4 Tilt Shaft Assembly Chain Assembly, Pan Chain Assembly, Tilt Sprocket, 25B20-3/8 W/SS Tilt Table Cover Bracket, Pan & Tilt Motor, Black Sprocket, Motor Bracket, Pan Limit (Non-SL Only) Plate Bottom Sideplate, Pan Spindle Sprocket, 25B13-3/8 Motor, Pan 2-RPM, 24 VAC Plate, Side Tilt (Non PP) Plate, Side Tilt (PP) Bracket, Pan Motor Spacer, Pan Motor Sprocket, Pan Spindle Limit Stop, Pan Connector, 6-Position (SL and P Only) Gromet, Neoprene Gromet, Neoprene (SL) Motor, 24 VAC, 1-RPM Spacer, 5/16 Dia X 1.25 #10 Clear Switch, Micro Switch, Micro (SL) Switch Actuator W/Insulator Switch Actuator W/Insulator (SL) Terminal Strip, 7-pin (Non-PP) Terminal Strip, 9-pin (PP Only) UL, Gland SL-9 UL, Nut Bracket, PM200C Bracket, Slip Ring (SL/PP) Bracket, Slip Ring (P/PP) Cover, Slip Ring Ring, Slip for Preset (SL/PP) Ring, Slip 24-inch Leads (SL) Part Number 15510000 15510000 1554049COMP 2804003COMP 1554049TCOMP 1554050COMP 1554052COMP 1554053COMP 17510000 25010002 2504007COMP 2504015COMP 2506000 2506001 2701002COMP 2801010COMP 2701004COMP 27012008 2704003COMP 2704004COMP 2704006COMP 2704010COMP 2704051COMP 2704100COMP 270412COMP 274105COMP 28012011 2804001COMP 2804002COMP 2804102COMP 2804012COMP 2804013COMP 2804019COMP 5804006COMP CONMAB6100 GRO2172N GRO2172N PS78001 SPA8548 SWI1SM1 SWI1SM1 SWIJS138B SWIJS138B TRS2007 TRS2009 EH400010003 EH400010004 PM200C4000COMP SL28004101COMP SL28004001COMP SL28004100COMP 250010000 28010000 25 Item Qty 45 1 1 1 1 1 1 1 1 1 1 1 1 46 47 48 49 50 51 52 53 Description Part Number Gear, SP Delrin (SL/PP) Gear, 1.875 Plastic (P/PP) Gear, SP Delrin Bracket, Pot Pan (P/PP) Bracket, Pot Pan (SL/PP) Bracket, Pot Pan Gear, Preset Pan Spindle Gear, Preset Tilt Shaft Connector, 9-position (PP Only) Pot, Dual Arm Pre Res (SL/PP) Pot, Precision, 10K (P/PP) Gear, 1.875 Plastic (P/PP) 280010016 PT250010002 28010017 2804014COMP 2804117COMP 2804015COMP 2804016COMP 2804020COMP CON206705-1 POTDARM010.0K POT010.0K POT10.0K 12.1 MECHANICAL HARDWARE LIST (PT2801000ASSY) The following parts list corresponds to the exploded assembly diagram in Figure 21. Item Qty A B C D E F G H I J 4 3 3 1 2 6 1 8 8 8 4 1 1 6 4 1 6 2 4 4 2 3 4 2 4 4 7 3 3 6 3 1 7 4 1 1 1 K L M N O P Q R S T U V W X Y Z AA BB CC DD EE FF GG 26 Description Part Number Bolt, 1/4-20 X 5/8 Phil Flat SS Screw, 1/4-20 X 5/8 Hex C/S SS (SL Only) Washer, Split Lock Medium (SL Only) Screw, 10-32 X 3/8 Pan Phil SS (SL Only) Screw, 10-32 X 7/16 Socket Head C/S SS Screw, 10-32 X 1/2 Socket Head C/S SS #10 Internal Tooth Lockwasher (SL Only) Washer, Split Lock #10 SS Medium Washer, Flat #10 SS Screw, 2-56 X 4/16 Pan Phil SS Screw, 2-56 X 4/16 Pan Phil SS (SL) Set Screw, 10/32 X 1/8 Socket Knurl Blk Set Screw, 10/32 X 3/16 Socket Knurl Blk Screw, 4-40 X 1/4 Pan Phil SS Screw, 4-40 X 3/8 Pan Phil (PP Only) Screw, 4-40 X 5/8 Pan Phil SS #4 Internal Tooth Lockwasher SS Set Screw, 6-32 X 3/16 Socket Knurl Blk Screw, 6-32 X 1/4 Pan Phil SS Screw, 6-32 X 3/8 Socket C/S SS Screw, 6-32 X 3/8 Pan Phil SS Screw, 6-32 X 1/2 Socket C/S Set Screw, 6-32 X 3/4 SS Screw, 6-32 X 2 Pan Phil SS Nut, 6-32 Acorn SS Nut, Hex 6-32 SS #6 Internal Tooth Lockwasher (PP Only) #6 Internal Tooth Lockwasher (P Only) Washer, Split Lock #6 SS Med Screw, 8-32 X 3/8 Pan Phil SS (SL Only) Screw, 8-32 X 3/8 Pan Phil SS (P Only) Screw, 8-32 X 5/8 Pan Phil SS Washer, Internal Star (SL Only) Washer, Internal Star (P Only) Pin, Roll 3/32 X 1/2 Pin, Roll 3/32 X 1/2 Pin, Dowel 1/8 X 5/8 Hardened Steel ZH1/420X.625SFS ZH1/420X.625CH ZH1/4LWSSL ZH10-32X.375SPP ZH10-32X.437CS ZH10-32X.500CS ZH10LWSIS ZH10LWSSL ZH204X436X60C ZH2-56X.437SPP ZH2-56X.437SPP ZH10-32X.187S ZH3/8-24X.375SS ZH4-40X.250SPP ZH4-40X.375SPP ZH4-40X.625SPP ZH4LWSIS ZH6-32X.187S ZH6-32X.250SPP ZH6-32X.375CS ZH6-32X.375SPP ZH6-32X. 500CS ZH6-32X.750SS ZH6-32X2.00SPS ZH6-32NUTCA ZH6-32NUTSH ZH6LWSIS ZH6LWSIS ZH6LWSSL ZH8-32X.375SPP ZH8-32X.375SPP ZH8-32X.375SPP ZH8LWSIS ZH8LWSIS ZHPIN3/32X1/2R ZHPIN3/32X3/4R 1510001 PELCO Manual C460M-E (7/95) 13.0 ENCLOSURE MODELS ED28 Harris environmental discreet surveillance enclosure with black opaque lower dome with clear viewing window for outdoor applications. Fixed camera mount supplied. (UL, CE) ED2820SL-RX/PP Same as ED2820SL-RX except sup- plied with PT2801003ASSY pan/tilt assembly with 360° pan rotation and preset positioning capabilities. (UL) ED2820-WX Same as ED2820-RX except has Wiretron receiver/driver. ED28-1 Same as ED28 except supplied with factory installed heater/blower and service light. (UL) ED2820SL-WX Same as ED2820-WX except supplied with PT2801001ASSY pan/tilt assembly with 360° pan rotation. (UL) ED2820 Harris environmental discreet surveillance system factory assembled with PT2801000ASSY pan/tilt assembly. Heater/blower and service light are standard features. (UL) ED29 Same as ED28 except pendant mount version. ED29-1 Same as ED28-1 except pendant mount version. ED2820-3 Same as ED2820 except 230 VAC blower, heater and service light. ED29-3 Same as ED29-1 except 230 VAC blower/heater with service light. (CE) ED2820-PP Same as ED2820 except supplied with PT2801002ASSY pan/tilt assembly with preset positioning capabilities. (UL) ED2920 Same as ED2820 except pendant mount version. (UL) ED2920-3 Same as ED2920 except 230 VAC blower/heater and service light. ED2920-RX Same as ED28280-RX except pendant mount version. ED2920-SL Same as ED2820-SL except pendant mount version. (UL) ED2820-RX Harris environmental discreet surveillance system factory assembled with PT2801000ASSY pan/tilt and Coaxitron receiver/driver. Heater/ blower and service light are standard features. (UL) ED2820-RX/PP Same as ED2820-RX except supplied with PT2801002ASSY preset position feedback pan/tilt assembly. (UL) ED2820-SL Same as ED2820 except supplied with PT2801001ASSY pan/tilt assembly with 360° pan rotation. (UL) ED2820SL/PP Same as ED2820-SL except supplied with PT2801003ASSY pan/tilt assembly with 360° pan rotation and preset positioning capabilities. (UL) ED2920SL-RX Same as ED2820SL-RX except pendant mount version. (UL) NOTE: ED29/ED2920 Series domes require a suitable length of 1-1/2" NPT threaded pipe for mounting. 13.1 OPTIONS ED2820-3SL/PP Same as ED2820SL/PP except 230 VAC blower/heater and service light. ED2820SL-RX Same as ED2820-RX except supplied with PT2801001ASSY pan/tilt assembly with 360° pan rotation. (UL) PELCO Manual C460M-E (7/95) ED28KIT Installation kit; required to retrofit ED28, ED28-1, ED29, or ED29-1 dome with pan/tilt assembly. (See Section 17.) TI2800 Low temperature kit; thermal insulation with two 80 watt heaters to allow operation in temperatures below -10°F (-23°C). 27 14.0 ENCLOSURE SPECIFICATIONS Fuse Protection: 3 AG type MECHANICAL Enclosure Dome Drive: Dome rides on rollers and is driven by drive arm of pan/tilt Control Method: 15-pulse train (pulse width modulated) superimposed on the video signal during the vertical interval by the control transmitter. Pulse train occupies one TV line period. Max. Camera/Lens Length: 14.0 inches (35.5 cm) ELECTRICAL Enclosure (All models except ED28/ED29) Input Voltage: Power Requirements: Blower: 120 VAC 50/60Hz (or 230 VAC, 50/ 60 Hz for ED2820-3 and ED28203SL/PP, ED29-3) 80 cfm at 13 watts (or 90 cfm at 15 watts for ED2820-3 and ED28203SL/PP only) Two (2) at 80 watts each Service Light: One (1) at 7 watts (or One (1) at 10 watts for ED2820-3 and ED28203SL/PP only) 3-wire grounded, 18 Awg (supplied on “RX” versions only) Receiver (Models ED2820-RX, ED2820SL-RX, ED2820-RX/ PP, ED2820SL-RX/PP, ED2820-WX, ED2820SL-WX, ED2920-RX, and ED2920SL-RX only) Power Cord: 3 wire grounded, 18 Awg (supplied) Cables: Coaxitron Video: RG59 with BNC jack Control: RG59 with BNC jack Wiretron Video: Coax Control: Twisted pair, unshielded Input Voltage: Power Requirements: 28 System Bandwidth: Operating Distance: 180 vA (or 185 vA for ED2820-3 and ED2820-3SL/PP only) Heaters: Power Cable Requirements: Input Video Line:1 v p-p nominal; 2v p-p maximum at less than 75% APL; 1.5v p-p maximum at 90% APL. 120 VAC, 50/60Hz Less than 2 dB down at 10 MHz 750 feet (228m) on RG59U 1,500 feet (457m) on RG6 1,800 feet (548m) on RG11 (75 ohm coax required) GENERAL Enclosure Dimensions: Construction: Upper Box Lower Dome See Figures 1 and 2 Formed aluminum Acrylic hemisphere with distortion free viewing window Finish: Polyvinyl powder coat Weight: ED28 25 lbs (11.34 kg) ED28-1 27 lbs (12.25 kg) ED2820, ED2820-3 ED2820-SL, ED2820-3SL/PP, ED2820SL/PP 35 lbs (15.75 kg) ED2820-RX, ED2820SL-RX, ED2820SL-RX/PP, ED2820-WX, ED2820SL-WX 42 lbs (18.90 kg) ED29, ED2920 Series 47 lbs (21.291 kg) Temp. Range: -10°F to 140°F (-23°C to +60°C) 79 vA (receiver only) PELCO Manual C460M-E (7/95) 15.0 PAN/TILT ASSEMBLIES 15.1 ASSEMBLY DESCRIPTION ELECTRICAL The pan/tilt assembly is a “mini” light duty pan/tilt for loads up to 15 lbs (6.8 kg) and is factory pre-wired for all control functions (pan and tilt, motorized zoom lens, 24 VAC camera power, and video). All connections are made at the input connector, eliminating the need for wiring harnesses. This greatly reduces installation time, while increasing reliability and serviceability. Input Voltage: Power Requirements: Running Pan — .31 amp (7.5 vA) Tilt — .38 amp (9.2 vA) Starting Pan — .47 amp (11.2 vA) Tilt — .56 amp (13.5 vA) 15.2 ASSEMBLY MODELS PT2801000ASSY Mini light-duty pan/tilt, 24 VAC, with 0-355° pan and tilt 24 VAC required for pan/tilt Maximum Current: PT2801001ASSY Mini light duty pan/tilt with 360° pan rotation, 24 VAC 2 amps per conductor (SL models only) Connectors: Pan/Tilt Amp CPC type (mate supplied). Installed onto a pigtail exiting from base of pan/tilt (all functions — camera power, lens, video, pan/tilt). PT2801002ASSY Same as PT2801000ASSY except with position feedback modification which allows pan/tilt to be automatically positioned to various preset positions PT2801003ASSY Same as PT2801001ASSY except with position feedback modification which allows pan/tilt to be automatically positioned to various preset positions Lens: Hirschmann MAB6100 Video: BNC Camera Power: Spade lugs Motors: Two-phase induction type. Continuous duty, instantaneous reversing 16.0 ASSEMBLY SPECIFICATIONS MECHANICAL Pan: Movement in horizontal plane: PT2801000ASSY, PT2801002ASSY 0-355° @ 10°/sec ±1° PT2801001ASSY, PT2801003ASSY 360° Tilt: ±90° movement in vertical plane at 3°/sec ±.5° (no load condition) Maximum Load: 15 lbs (6.8 kg) PELCO Manual C460M-E (7/95) Limit Switches: Pan — 5 amp Tilt — 5 amp External adjustment Cable Distances: (See Section 8.2) GENERAL Construction: Aluminum (Product specifications subject to change without notice.) 29 17.0 PAN/TILT ASSEMBLY INSTALLATION 2. This section covers the installation of the ED28KIT in retrofitting a non-pan/tilt-equipped ED28 and ED28-1 or ED29/ED29-1/ED29-3 Harris Dome with a pan/tilt assembly unit. Please read through and understand the installation instructions before proceeding with the installation. Again, make sure the dome drive bracket is oriented correctly so the front of the pan and tilt assembly will face the viewing slot in the dome enclosure. 3. Mount the pan and tilt assembly, with the installed dome drive bracket and the assembly mounting bracket, to the inside of the enclosure. Make sure the direction of the pan and tilt assembly is oriented properly. 4. Make sure all hardware is tightened securely. 5. Make the proper electrical connections. NOTE: When installing a pan/tilt unit to a dome enclosure, it is recommended that one of the following pan/tilt assembly units be used in the installation: PT2801000ASSY – for non-PP operation PT2801001ASSY – for SL operation PT2801002ASSY – for PP operation PT2801003ASSY – for SL/PP operation NOTE: Refer to Installation/Operation manual C460M for complete wiring and operation information. (The pan/tilt assembly must be ordered separately.) Before proceeding with the installation, make sure you have the following: Install the dome drive bracket to the top of the pan and tilt assembly using the (2) mounting screws and washers as shown in Figure 21. 6. Close the dome, aligning the dome drive bracket with the drive tab on the edge of the dome. (1) P/T assembly mounting bracket, PM200C4000COMP (1) Dome Drive Bracket, SB34105COMP See Figure 21 for the assorted mounting hardware part numbers and quantities. NOTE: If you are working with a SL (360°) pan/ tilt assembly unit (PT2801001ASSY, or PT2801003ASSY), skip to step 2 in the following instructions. 1. Install the pan and tilt assembly mounting bracket to the top of the pan and tilt unit using the (3) mounting screws and washers as shown in Figure 21. Make sure the bracket is oriented such that when the pan and tilt assembly is mounted to it, the front of the pan and tilt unit will face toward the viewing slot in the enclosure dome. 30 PELCO Manual C460M-E (7/95) Figure 21. ED28KIT Installation/Exploded View Exploded Assembly Parts List Item Qty Description Part Number 1 2 1 1 Bracket Dome drive bracket PM200C4000COMP SB34105COMP A B C D E F 3 2 3 5 2 2 Bolt, 1/4-20 x 5/8" hex C/S Nut lock, 1/4-20, nylon insert SS Washer, split lock, 1/4" SS Washer, flat, nylon Screw, 10-32 x 3/8", pan phil SS Washer, split lock #10 SS ZH1/4-20X.625CH ZH1/420NUTCHN ZH1/4LWSSL ZH260X562X65C ZH10-32X.375SPP ZH10LWSSL PELCO Manual C460M-E (7/95) 31 18.0 WARRANTY AND RETURN INFORMATION WARRANTY RETURNS Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair). • Five years on FT/FR8000 Series fiber optic products. All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge. • Three years on Genex® Series products (multiplexers, server, and keyboard). • Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a five-year warranty. • Two years on standard motorized or fixed focal length lenses. • Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products. • Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in continuous motion applications. • Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades). • Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura ™ Series distributed network-based video products. • One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months. • Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes). Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty. Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise. The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state to state. If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information: Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below. If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to: Service Department Pelco 3500 Pelco Way Clovis, CA 93612-5699 If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the following: If the goods are to be sent by a COURIER SERVICE, send the goods to: Pelco 3500 Pelco Way Clovis, CA 93612-5699 USA If the goods are to be sent by a FREIGHT FORWARDER, send the goods to: Pelco c/o Expeditors 473 Eccles Avenue South San Francisco, CA 94080 USA Phone: 650-737-1700 Fax: 650-737-0933 1. Model and serial number 2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number 3. Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written explanation with the product when returned. Method of return shipment shall be the same or equal to the method by which the item was received by Pelco. This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment. 32 PELCO Manual C460M-E (7/95)
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Copy, Extract, Print high-res XMP Toolkit : 3.1-702 About : uuid:07caacd6-bab5-11da-bc5d-000a95a25184 Producer : Acrobat Distiller 6.0.1 for Macintosh Keywords : Camera Site Equipment|Fixed Domes Creator Tool : Adobe PageMaker 7.0 Create Date : 2005:11:07 09:23:45-08:00 Modify Date : 2006:04:04 08:26:30-07:00 Metadata Date : 2006:04:04 08:26:30-07:00 Document ID : uuid:45591ebc-4fb3-11da-9b74-000a95a25184 Instance ID : uuid:77eaa020-0f89-4821-8a14-bf298f4df067 Format : application/pdf Title : Pelco ED28_ED2820 and ED29_ED2920 Harris Dome Enclosures_manual Description : Obsolete Creator : llinarez Subject : Camera Site Equipment|Enclosures|Outdoor Page Count : 36 Author : llinarezEXIF Metadata provided by EXIF.tools