Pella 13N90000 Integrated Patio Door Sensor User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3030336
Application ID	b9Dy9g+MINspX7VB8/oHnQ==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	182.01kB (2275118 bits)
Date Submitted	2016-06-16 00:00:00
Date Available	2016-12-13 00:00:00
Creation Date	2016-06-13 15:37:26
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2016-06-13 15:37:37
Document Title	User manual
Document Creator	Adobe InDesign CC 2015 (Macintosh)

PELLA® INSYNCTIVE® PRODUCT GUIDE
INTEGRATED
PATIO DOOR SENSORS
INTEGRATED PATIO DOOR SENSORS communicate the opened or closed and
locked or unlocked status of your Patio Door by Pella to BRIDGE.
WHAT’S NEEDED:
• PELLA® INSYNCTIVE® BRIDGE (required — sold separately): Wirelessly connects your Insynctive
products to STATUS INDICATOR or a compatible home automation system.*
• PELLA INSYNCTIVE STATUS INDICATOR (optional — sold separately): Indicates status of Pella
Insynctive SENSORS. Or you can use a compatible home automation system to help monitor
your windows and doors.*
• SMALL FLATHEAD SCREWDRIVER
For a list of compatible home automation systems, visit Insynctive.Pella.com.
PE LLA ® I N SYN CTI VE ® I N TE G R ATE D PATI O DO O R SE N SO R P ROD UCT GUID E | 1
TABLE OF CONTENTS
General and Safety Information
Registering Products
Need Help?
Have a Home Automation System?
Warnings
Product Overview
Specifications
Detailed Instructions
Integrated Patio Door Sensor Setup
Additional Instructions
Product Manufacturer’s Code
Care and Maintenance
Replacing Batteries
Deleting Sensors
14		
16
17		
Troubleshooting
FCC Compliance and Industry Canada
Limited Warranty
Software License Agreement and Privacy Policy
PE LLA ® I N SYN CTI VE ® I N TE G R ATE D PATI O DO O R SE N SO R P ROD UCT GUID E | 2
GENER AL AND SAFE T Y INFORMATION
REGISTERING PRODUCTS
Visit Insynctive.Pella.com/Registration to register your new Pella® Insynctive® products.
NEED HELP?
For instant access to warranties, troubleshooting information and videos, visit
Insynctive.Pella.com/Support or call 855-473-5524.
HAVE A HOME AUTOMATION SYSTEM?
To view a list of compatible systems and find instructions on how to sync Pella Insynctive products,
visit Insynctive.Pella.com.
WARNING
Failure to adhere to the warnings below may result in death, serious injury and/or loss of valuables.
• Pella Insynctive INTEGRATED PATIO DOOR SENSORS are not 100% reliable for a variety of reasons.
For example, SENSORS:
— communicate data wirelessly, and wireless data is susceptible to interference or failure.
— require proper installation.
— require a battery with an adequate charge.
— may be damaged after installation.
Therefore, Pella Insynctive products should not be relied upon in situations where life, safety and/or
protection of valuables are solely dependent on their function. Test each product at least once per
year to help ensure proper operation.
• Use caution when windows are open and when removing the transmitter to avoid a fall out of a
window. Keep children and pets away from open windows.
• Pella Insynctive products are not a substitute for careful adult supervision of children.
• Keep battery and other small parts out of the reach of children. If small parts are swallowed,
immediately seek medical help.
• Batteries carry the risk of fire, explosion and burns. Do not recharge, disassemble or incinerate.
• INTEGRATED PATIO DOOR SENSORS may indicate a patio door is closed, but water intrusion may
occur during rain. Patio doors should be closed and locked for optimal performance in rain.
PE LLA ® I N SYN CTI VE ® I N TE G R ATE D PATI O DO O R SE N SO R P ROD UCT GUID E | 3
PRODUC T OV ERV IE W
INTEGRATED PATIO DOOR SENSORS wirelessly
communicate the locked or unlocked and opened
or closed status of Patio Doors by Pella to Insynctive®
BRIDGE.
Information is wirelessly relayed from BRIDGE
to STATUS INDICATOR or a compatible home
automation system,* where locked or unlocked and
opened or closed status can be monitored.
Sensors are integrated into Patio Doors by Pella
ordered with Insynctive technology, making them
virtually unnoticeable.
HINGED PATIO DOOR
LOCK SENSOR
HINGED PATIO DOOR
OPEN/CLOSE SENSOR
For a list of compatible home automation systems, visit Insynctive.Pella.com.
SLIDING PATIO DOOR
LOCK SENSOR
SLIDING PATIO DOOR
OPEN/CLOSE SENSOR
SPECIFICATIONS
Frequency: 433.92MHz (Insynctive)
Operating Temperature: -22° to 140°F (-30° to 60°C)
Operating Humidity: 5% to 95% RH noncondensing
Lock Sensor Battery: 3V lithium CR2032
Open/Close Sensor Battery: 3V lithium CR2
Typical Battery Life: 10 years (based on operating temperatures of 32° to 120°F
[0°to 49°C], may vary by use)
Magnet Gap: 5/16" max between patio door panel and hinged door head or
sliding door lock jamb
PE LLA ® I N SYN CTI VE ® I N TE G R ATE D PATI O DO O R SE N SO R P ROD UCT GUID E | 4
DE TAILED INS TRUC TIONS
INTEGRATED PATIO DOOR SENSOR SETUP
See Insynctive.Pella.com/Support for how-to videos.
BRIDGE
Plug BRIDGE into an electrical outlet (light will turn green and then
flash blue).
TEST
BUTTON
SYNC
BUTTON
1. Get Started
LIGHT
2. Prepare OPEN/CLOSE SENSOR
Sliding Patio Doors: Use a small flathead screwdriver to remove
the plastic endcap from the OPEN/CLOSE SENSOR. Grip the edges
of the circuit board and pull it out to gain access to the battery.
Remove the plastic battery tab from the battery, then reinsert
the OPEN/CLOSE SENSOR into your entry door. Install the plastic
endcap back onto OPEN/CLOSE SENSOR.
PLASTIC
ENDCAP
SLIDING PATIO DOOR
OPEN/CLOSE SENSOR
Hinged Patio Doors: Pull the plastic battery tab from OPEN/CLOSE
SENSOR.
NOTE: Once the plastic tab is removed from the battery, you
will have 2 minutes to sync OPEN/CLOSE SENSOR to BRIDGE.
If 2 minutes pass without successfully syncing, follow steps for
removing and reinserting the battery on pages 9 – 10.
You are ready to sync OPEN/CLOSE SENSOR to BRIDGE.
PLASTIC
TAB
3. Sync OPEN/CLOSE SENSOR to BRIDGE
OPEN/CLOSE
SENSOR
Each INTEGRATED PATIO DOOR SENSOR will need to be synced
to BRIDGE.
HINGED PATIO DOOR
OPEN/CLOSE SENSOR
BATTERY
TAB
HINGED PATIO DOOR
OPEN/CLOSE SENSOR
PE LLA ® I N SYN CTI VE ® I N TE G R ATE D PATI O DO O R SE N SO R P ROD UCT GUID E | 5
DE TAI L E D IN STRU CTIONS
BRIDGE
TEST
BUTTON
SYNC
BUTTON
LIGHT
(c o nti nue d )
WITHOUT HOME AUTOMATION (Stand-Alone Mode)
Press and hold BRIDGE Sync button until light begins flashing
orange. The Sync button is the bottom button located on the side
of BRIDGE.
NOTE: BRIDGE is in sync mode while the orange light is flashing.
BRIDGE will remain in sync mode for 2 minutes. BRIDGE will then
beep, and orange light will turn off to indicate BRIDGE exited
sync mode.
To sync OPEN/CLOSE SENSOR to BRIDGE, open then close
the active panel of your patio door 2 times within 5 seconds.
NOTE: For double-hinged doors, the passive panel must be closed
and bolted during this process.
Wait for the light on BRIDGE to flash green and beep for 2 seconds.
This will indicate a successful sync.
SLIDING PATIO DOOR
HINGED
PATIO DOOR
If OPEN/CLOSE SENSOR sync is unsuccessful, return to Step 2 and
retry the process.
4. Prepare LOCK SENSOR
This lock transmitter is used in multiple INTEGRATED SENSOR
units. The lock transmitter must learn what type of patio door it will
be housed in. Follow the steps below to prep the lock transmitter.
SLIDING PATIO DOOR
LOCK SENSOR
Remove the lock transmitter from the patio door, and lift up a
corner of the plastic cover to expose the battery.
Remove the plastic tab separating the battery from the device. Push
down on the battery to ensure that the battery is firmly in place.
Make sure plastic cover is flat and in place.
NOTE: Once the plastic tab is removed from the battery, you will
have 2 minutes for your lock transmitter to learn what type of patio
door it will be housed in. If 2 minutes pass without the transmitter
successfully learning your patio door type, remove and insert the
battery again.
HINGED PATIO DOOR
LOCK SENSOR
PLASTIC COVER
BATTERY
TAB
Insert the lock transmitter back into your patio door; close and lock
the patio door and wait 10 seconds. The lock transmitter has now
learned what type of patio door it is housed in.
You are ready to sync LOCK SENSOR to BRIDGE.
BATTERY TAB
REMOVED
PE LLA ® I N SYN CTI VE ® I N TE G R ATE D PATI O DO O R SE N SO R P ROD UCT GUID E | 6
DE TAI L E D IN STRU CTIONS
(c o nti nue d )
5. Sync LOCK SENSOR to BRIDGE
BRIDGE
TEST
BUTTON
SYNC
BUTTON
LIGHT
Each INTEGRATED PATIO DOOR SENSOR will need to be synced
to BRIDGE. You will have 2 minutes after completing Step 4 to
complete this step. If syncing is not successful within 2 minutes,
remove then replace the battery and repeat steps 4 and 5.
Press and hold BRIDGE Sync button until light begins flashing
orange. The Sync button is the bottom button located on the side
of BRIDGE.
NOTE: BRIDGE is in sync mode while the orange light is flashing.
BRIDGE will remain in sync mode for 2 minutes. BRIDGE will then
beep, and orange light will turn off to indicate BRIDGE exited
sync mode.
LOCKED
UNLOCKED
SLIDING PATIO DOOR
Sliding Patio Doors: To sync LOCK SENSOR to BRIDGE, unlock
and open your patio door slightly, then lock and close door 2 times
within 10 seconds.
Hinged Patio Doors: To sync LOCK SENSOR to BRIDGE, unlock
then lock your patio door 2 times within 10 seconds.
Wait for the light on BRIDGE to flash green and beep for
2 seconds. This will indicate a successful sync.
If LOCK SENSOR sync is unsuccessful, unlock then lock your patio
door 2 more times within 10 seconds. Then wait until BRIDGE
indicates a successful sync.
LOCKED
UNLOCKED
HINGED PATIO DOOR
NOTE: If syncing is still not successful, remove then reinsert the
battery and repeat steps 4 and 5.
Repeat the previous steps until all INTEGRATED PATIO DOOR
SENSORS have been synced to BRIDGE.
To exit sync mode, press and hold Sync button on BRIDGE until
light stops flashing orange.
WITH HOME AUTOMATION
BRIDGE supports two types of home automation systems,
Professionally Installed and Do-It-Yourself (DIY) Z-Wave. For a list of
compatible home automation systems or syncing instructions, visit
Insynctive.Pella.com.
PE LLA ® I N SYN CTI VE ® I N TE G R ATE D PATI O DO O R SE N SO R P ROD UCT GUID E | 7
DE TAI L E D IN STRU CTIONS
(c o nti nue d )
6. Test INTEGRATED PATIO DOOR SENSORS
Each INTEGRATED PATIO DOOR SENSOR should be tested to
ensure proper function after it is synced.
BRIDGE
TEST
BUTTON
SYNC
BUTTON
LIGHT
To test LOCK SENSOR, use the following procedure:
Unlock your patio door and verify that LOCK SENSOR reports the
product as unlocked on STATUS INDICATOR or compatible home
automation system. BRIDGE will beep twice.
To test OPEN/CLOSE SENSOR, use the following procedure:
Open your patio door and verify that OPEN/CLOSE SENSOR
reports the product as opened on STATUS INDICATOR or
compatible home automation system. BRIDGE will beep 2 times.
LOCKED
UNLOCKED
SLIDING PATIO DOOR
For double doors, also verify that retracting the bolt on the
passive panel causes the OPEN/CLOSE SENSOR to report as
opened on STATUS INDICATOR or compatible home automation
system. BRIDGE will beep twice.
If any of these steps fail, see the troubleshooting information on
page 14.
NOTE: If you have selected the chimes to be off, BRIDGE will
not beep. See Bridge Product Guide for information on setting
up chimes.
LOCKED
UNLOCKED
HINGED PATIO DOOR
SLIDING PATIO DOOR
HINGED
PATIO DOOR
PE LLA ® I N SYN CTI VE ® I N TE G R ATE D PATI O DO O R SE N SO R P ROD UCT GUID E | 8
ADDITIONAL INS TRUC TIONS
PRODUCT CODE
SLIDING PATIO DOOR
OPEN/CLOSE SENSOR
PRODUCT CODE
HINGED PATIO DOOR
OPEN/CLOSE SENSOR
HOW TO FIND PRODUCT MANUFACTURER’S CODE
Each Pella® Insynctive® product contains a label with a Manufacturer’s
Code that will be required to help Pella Customer Service identify
the product if service is required. To locate the Manufacturer’s Code
for OPEN/CLOSE SENSOR, remove battery cover and carefully pull
out circuit board. The label is on the circuit board. To locate the
Manufacturer’s Code for LOCK SENSOR, pull lock transmitter from
your patio door. The label is on the circuit board next to the battery.
NOTE: Electrostatic-sensitive. Avoid touching the antenna or circuit
board when accessing the Manufacturer’s Code.
CARE AND MAINTENANCE
• Test Insynctive products at least once per year to help ensure
proper operation.
BATTERY
CIRCUIT BOARD
MANUFACTURER’S
CODE
LOCK SENSOR
• Do not paint over SENSORS.
REPLACING BATTERIES
See Insynctive.Pella.com/Support for how-to videos.
When INTEGRATED PATIO DOOR SENSOR batteries are low, a signal
will be sent to BRIDGE. To aid in identifying which SENSOR has a low
battery, BRIDGE will beep twice and then issue a long tone when
INTEGRATED PATIO DOOR SENSOR with the low battery changes
from locked to unlocked or opened to closed.
To replace battery on OPEN/CLOSE SENSOR for Sliding Patio Door:
• Use a flathead screwdriver to carefully remove the plastic endcap
from the OPEN/CLOSE SENSOR.
PLASTIC
ENDCAP
• Grip the edges of the circuit board and pull it out to gain access to
the battery.
• Carefully slide out the battery and replace with a CR2 battery.
SLIDING PATIO DOOR
OPEN/CLOSE SENSOR
CIRCUIT BOARD
• Slide circuit board back inside OPEN/CLOSE SENSOR and install
the plastic endcap back onto OPEN/CLOSE SENSOR.
• Wait 2 minutes, then test OPEN/CLOSE SENSOR by opening the
patio door with installed OPEN/CLOSE SENSOR. BRIDGE should
beep twice. Resyncing OPEN/CLOSE SENSOR is not required after
battery change.
BATTERY
PE LLA ® I N SYN CTI VE ® I N TE G R ATE D PATI O DO O R SE N SO R P ROD UCT GUID E | 9
AD D I TI ON A L IN STRU CT ION S
(c o nti nue d )
To replace the battery on OPEN/CLOSE SENSOR for
Hinged Patio Door:
• Use a flathead screwdriver to carefully remove the plastic
endcap from the OPEN/CLOSE SENSOR.
HINGED PATIO DOOR
OPEN/CLOSE SENSOR
• Carefully slide out the battery and replace with a CR2 battery.
• Install the plastic endcap back onto the OPEN/CLOSE SENSOR.
• Wait 2 minutes, then test OPEN/CLOSE SENSOR by opening
your patio door with installed OPEN/CLOSE SENSOR. BRIDGE
should beep twice. Resyncing OPEN/CLOSE SENSOR is not
required after battery change.
HINGED PATIO DOOR
OPEN/CLOSE SENSOR BATTERY
To replace the battery on LOCK SENSOR:
• Remove the lock transmitter from your patio door, then lift up
the corner of the plastic cover to reveal the battery.
• Carefully replace with a CR2032 battery, ensuring that the plus
(+) side of the battery faces toward you.
• Replace clear plastic cover over battery and ensure that battery
is seated, then insert lock transmitter back into your patio door.
• Close and lock your patio door within 2 minutes of replacing
the battery to teach LOCK SENSOR what type of product it is
installed in.
HINGED PATIO DOOR LOCK SENSOR
• Wait 2 minutes, then test LOCK SENSOR by unlocking your patio
door with installed LOCK SENSOR. BRIDGE should beep twice.
Resyncing LOCK SENSOR is not required after battery change.
WARNING: Batteries carry the risk of fire, explosion and 		
burns. Do not recharge, disassemble or incinerate.
SLIDING PATIO DOOR LOCK SENSOR
CLEAR PLASTIC
COVER
BATTERY
P ELLA ® I N SYN CTI VE ® I N TE G R ATE D PATI O DO O R SE N SO R P R OD UCT GUID E | 10
AD D I TI ON A L IN STRU CT ION S
(c o nti nue d )
IMPORTANT NOTES:
• Electrostatic-sensitive. Avoid touching the antenna or circuit
board when changing the battery.
• Failure to change battery promptly when low will impair
INTEGRATED PATIO DOOR SENSOR performance.
PLASTIC
ENDCAP
SLIDING PATIO DOOR
OPEN/CLOSE SENSOR
CIRCUIT BOARD
BATTERY
HINGED PATIO DOOR
OPEN/CLOSE SENSOR
• Properly dispose of used batteries based on your local
requirements. A best practice is to dispose of batteries at
your local home chemical collection center. California Only:
Contains perchlorate material. See dtsc.ca.gov/hazardouswaste/
perchlorate for any special handling regulations.
DELETING INTEGRATED PATIO DOOR SENSOR
Deleting INTEGRATED PATIO DOOR SENSORS may be needed if
you no longer have a use for INTEGRATED PATIO DOOR SENSORS.
See Insynctive.Pella.com/Support for how-to videos.
1. Prepare OPEN/CLOSE SENSOR
Sliding Patio Door: Use a small flathead screwdriver to remove the
plastic endcap from the OPEN/CLOSE SENSOR. Grip the edges of
the circuit board and pull it out to gain access to the battery. Slide
out the battery, then slide back in. Install the plastic endcap back
onto OPEN/CLOSE SENSOR.
Hinged Patio Door: Use a small flathead screwdriver to remove
the plastic endcap from OPEN/CLOSE SENSOR. Slide out the
battery, then slide back in. Install the plastic endcap back onto
OPEN/CLOSE SENSOR.
NOTE: Once the battery is removed, you will have 2 minutes to
delete OPEN/CLOSE SENSOR from BRIDGE. If 2 minutes pass
without successful deletion, remove and insert the battery again.
You are ready to delete OPEN/CLOSE SENSOR from BRIDGE.
HINGED PATIO DOOR
OPEN/CLOSE SENSOR BATTERY
2. Delete OPEN/CLOSE SENSOR from BRIDGE
Each INTEGRATED PATIO DOOR SENSOR will need to be deleted
from BRIDGE.
P ELLA ® I N SYN CTI VE ® I N TE G R ATE D PATI O DO O R SE N SO R P R OD UCT GUID E | 11
AD D I TI ON A L IN STRU CT ION S
BRIDGE
TEST
BUTTON
SYNC
BUTTON
LIGHT
(c o nti nue d )
WITHOUT HOME AUTOMATION (Stand-Alone Mode)
Press and hold BRIDGE Sync button until light begins flashing
orange. The Sync button is the bottom button located on the
side of BRIDGE.
NOTE: BRIDGE is in sync mode while the orange light is flashing.
BRIDGE will remain in sync mode for 2 minutes. BRIDGE will then
beep, and orange light will turn off to indicate BRIDGE exited
sync mode.
To delete OPEN/CLOSE SENSOR from BRIDGE, open then close
the active panel of your patio door 2 times within 5 seconds.
NOTE: For double doors, the passive panel must be closed and
bolted during this process.
Wait for the light on BRIDGE to flash red and beep 3 times. This
will indicate a successful deletion.
SLIDING PATIO DOOR
HINGED
PATIO DOOR
If OPEN/CLOSE SENSOR deletion is unsuccessful, return to Step
1 and retry the process.
3. Prepare LOCK SENSOR
Remove lock transmitter from patio door and lift up a corner
of the clear plastic cover to expose the battery. Remove and
reinsert the battery to place LOCK SENSOR in deletion mode for
2 minutes.
HINGED PATIO DOOR LOCK SENSOR
NOTE: If 2 minutes pass without a successful deletion, remove
and insert the battery again.
Insert the lock transmitter back into your patio door; close and
lock the patio door, then wait 10 seconds. The lock transmitter
has now learned what type of patio door it is housed in.
You are ready to delete LOCK SENSOR from BRIDGE.
4. Delete LOCK SENSOR from BRIDGE
SLIDING PATIO DOOR LOCK SENSOR
CLEAR PLASTIC
COVER
Press and hold BRIDGE Sync button until light begins flashing
orange. The Sync button is the bottom button located on the
side of BRIDGE.
BATTERY
P ELLA ® I N SYN CTI VE ® I N TE G R ATE D PATI O DO O R SE N SO R P R OD UCT GUID E | 12
AD D I TI ON A L IN STRU CT ION S
(c o nti nue d )
NOTE: BRIDGE is in sync mode while the orange light is
flashing. BRIDGE will remain in sync mode for 2 minutes.
BRIDGE will then beep, and orange light will turn off to indicate
BRIDGE exited sync mode.
BRIDGE
TEST
BUTTON
SYNC
BUTTON
LIGHT
Sliding Patio Doors: To delete LOCK SENSOR from BRIDGE,
unlock and open your patio door slightly, then lock and close
door 2 times within 10 seconds.
Hinged Patio Doors: To delete LOCK SENSOR from BRIDGE,
unlock then lock your patio door 2 times within 10 seconds.
Wait for the light on BRIDGE to flash red and beep 3 times. This
will indicate a successful deletion.
If LOCK SENSOR deletion is unsuccessful, return to Step 3 and
retry the process.
LOCKED
UNLOCKED
To exit sync mode, press and hold Sync button on BRIDGE until
light stops flashing orange.
SLIDING PATIO DOOR
WITH HOME AUTOMATION
BRIDGE supports two types of home automation system
Professionally Installed and Do-it-Yourself (DIY) Z-Wave. For
a list of compatible home automation systems and deletion
instructions, visit Insynctive.Pella.com.
LOCKED
UNLOCKED
HINGED PATIO DOOR
P ELLA ® I N SYN CTI VE ® I N TE G R ATE D PATI O DO O R SE N SO R P R OD UCT GUID E | 13
TROUBLESHOOTING
Also refer to Insynctive.Pella.com/Support for more troubleshooting information, including videos,
frequently asked questions and reference materials.
PROBLEM
CAUSE AND POSSIBLE SOLUTION
Cannot sync OPEN/CLOSE
SENSOR to BRIDGE.
Verify OPEN/CLOSE SENSOR battery is installed correctly
and plastic battery tab has been removed. See page 5 for
additional information.
Remove and reinstall battery to restart sync mode.
Move BRIDGE to the same room as OPEN/CLOSE SENSOR to
ensure that range is not the issue.
Verify magnet is in place on the frame of sliding doors or the top
of the panel on hinged doors.
Cannot sync LOCK SENSOR
to BRIDGE.
Verify LOCK SENSOR battery is installed correctly and plastic battery
tab has been removed. See page 6 for additional information.
Remove and reinstall battery to restart sync mode.
Move BRIDGE to the same room as LOCK SENSOR to ensure that
range is not an issue.
Sliding Door: Verify lock is functioning properly. When door is
locked, both the top and bottom strikes should appear to be
holding the door shut when pressure is applied.
Hinged Door: Verify lock is functioning properly. The door
should lock when knob is turned to the lock position. Check for
obstructions in the strike plates at the bottom of the door. Lock
bolts must extend completely into strikes.
BRIDGE does not beep when
patio door is unlocked.
Verify that BRIDGE chime feature is turned on. See Bridge Product
Guide for details.
Battery may be too low to operate LOCK SENSOR. Replace
battery. See page 10 for additional information.
LOCK SENSOR may be out of range. Move BRIDGE closer to LOCK
SENSOR. Verify that BRIDGE has power.
Verify the magnet is still in place.
P ELLA ® I N SYN CTI VE ® I N TE G R ATE D PATI O DO O R SE N SO R P R OD UCT GUID E | 14
TRO UBL ESHOOTIN G
(co nti nue d)
Also refer to Insynctive.Pella.com/Support for more troubleshooting information, including videos,
frequently asked questions and reference materials.
PROBLEM
CAUSE AND POSSIBLE SOLUTION
BRIDGE does not beep when
patio door is opened.
Verify that BRIDGE chime feature is turned on. See Bridge
Product Guide for details.
Battery may be too low to operate OPEN/CLOSE SENSOR.
Replace battery. See page 9 for additional information.
OPEN/CLOSE SENSOR may be out of range. Move BRIDGE
closer to OPEN/CLOSE SENSOR. Verify that BRIDGE has power.
Verify the magnet is still in place.
BRIDGE beeps 3 times when
patio door is opened.
Battery is low in OPEN/CLOSE SENSOR; replace battery.
BRIDGE beeps 3 times when
patio door is unlocked.
Battery is low in LOCK SENSOR; replace battery.
P ELLA ® I N SYN CTI VE ® I N TE G R ATE D PATI O DO O R SE N SO R P R OD UCT GUID E | 15
FCC COMPLIANCE AND INDUSTRY CANADA
This equipment has been tested and found to comply with the limits for Class B digital devices,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a different circuit from the receiver.
• Consult the dealer or an experienced radio/TV contractor for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by Pella Corporation could void the user’s
authority to operate the equipment.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS. L’opération
est soumise aux deux conditions suivantes: (1) cet appareil ne peut causer d’interférences, et (2)
cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un
mauvais fonctionnement de l’appareil.
Integrated Lock Sensor
FCC ID: SO7-13N80000
IC ID: 110009A-13N80000
Integrated Hinged Patio Door Open/Close Sensor
FCC ID: SO7-13N90000
IC ID: 110009A-13N90000
Integrated Sliding Patio Door Open/Close Sensor
FCC ID: SO7-205Z0000
IC ID: 11009A-205Z0000
P ELLA ® I N SYN CTI VE ® I N TE G R ATE D PATI O DO O R SE N SO R P R OD UCT GUID E | 16
LIMITED WARR ANT Y
A two-year limited warranty comes standard with purchase. For complete warranty details, visit
Insynctive.Pella.com/IntegratedSensor.
SOFTWARE LICENSE AGREEMENT AND
PRIVACY POLICY
Pella® Insynctive® products are covered by the Pella Insynctive products Software License Agreement and
Pella Insynctive products Privacy Policy in effect at the time of sale, which can be found at Insynctive.Pella.com.
By installing or using your Insynctive products, you are acknowledging that the Insynctive Software License
Agreement and Privacy Policy are part of the terms of sale.
© 2016 Pella Corporation
P ELLA ® I N SYN CTI VE ® I N TE G R ATE D PATI O DO O R SE N SO R P R OD UCT GUID E | 17

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c067 79.157747, 2015/03/30-23:40:42
Create Date                     : 2016:06:13 15:37:26-05:00
Metadata Date                   : 2016:06:13 15:37:37-05:00
Modify Date                     : 2016:06:13 15:37:37-05:00
Creator Tool                    : Adobe InDesign CC 2015 (Macintosh)
Instance ID                     : uuid:6555b8bd-d6fe-3640-87a3-04020a4a29d3
Original Document ID            : xmp.did:5F83C380FC206811822A94A2C40248AC
Document ID                     : xmp.id:a63ea0ac-c264-43f9-95ed-86271d652ecd
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:7c398145-be5e-486e-9843-db1b871bceb9
Derived From Document ID        : xmp.did:1d9aec69-26a0-475e-9926-4882e49696c8
Derived From Original Document ID: xmp.did:5F83C380FC206811822A94A2C40248AC
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2015 (Macintosh)
History Changed                 : /
History When                    : 2016:06:13 15:37:26-05:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Slug Checksum                   : 2771965578
Slug Post Script Name           : MinionPro-Regular
Slug Foundry                    : Adobe Systems
Slug Version                    : 2.030
Slug Outline File Size          : 0
Slug Family                     : Minion Pro
Slug Font Sense 12 Checksum     : 2771965578
Slug Font Kind                  : OpenType - PS
Slug Kerning Checksum           : 0
Page Count                      : 17
Creator                         : Adobe InDesign CC 2015 (Macintosh)

EXIF Metadata provided by EXIF.tools