Perfect Toys Co 30113-TX Remote Control Toy Transmitter User Manual
Perfect Toys International Co Ltd Remote Control Toy Transmitter Users Manual
Users Manual
1
TRANSMITTER’S MANUAL
ITEM NO.: 30113
INSTALLATION OF THE TRANSMITTER
BATTERY’S SETUP
Please use eight “AA” alkaline batteries or rechargeable batteries.
First: In light of arrow’s direction, push the cover of battery case away,
and lift it to sever the transmitter.
Second: Insert eight batteries and pay attention to batteries’ anode and
cathode.
Third: push the cover of battery case to original place.
Note: If using rechargeable batteries, you should use the intelligent
charger(No.40108). Its charging range is 1H—1.5H.
INDICATOR LIGHT
If having full electric energy in the transmitter, the green, the red, and the
yellow light will all on.
If the green light goes out, it indicates the electric energy is not full, and
possibly have half one.
If the yellow light blinks, it indicates the electric energy is not full, and
you should replace or recharge the batteries.
If the red light brights, you should replace or recharge the batteries.
2
EXPLANATION OF TRANSMITTER’S ANTENNA
Before turning on the transmitter, you should ensure if the antenna is set
up correctly, and is extended enough, Otherwise it will affect the range of
control largely, possible cause damage to your model, or injuries yourself
and someone else.
INSTALLATION OF THE RECEIVER AND THE SERVO
Before installation, please read these following instructions carefully in
order to avoid the dispensiable loss to yourself and some else.
Never let the receiver and the motor or the engine use one power supply
together.
1. Check if the switch of the receiver’s power supply is set on the “OFF”
position.
2. Set the switch of the receiver’s power supply to the circuit way of the
receiver’s power supply.
3. Set the throttle’s servo to the second channel of the receiver.
4. Set the turnable servo to the first channel of the receiver.
5. Insert four “AA” alkaline batteries to the battery case, and connect the
ports to the switch of the receiver.
6. Check if the frequency of the receiver crystal matches up to the one of
the transmitter crystal.
7. Turn on the transmitter.
3
8. Set the switch of the receiver to “ON” position.
WARNING:
1. It is a electric set. Please never put it in the moist place to avoid from
water entering.
2. Please observe the instructions on the manual strictly to operate or
install this set.
3. If because of your wrong operation processes, it causes damage to the
transmitter or injures yourself and somebody else, our company will
not take responsibility for any loss on these problems.
4. Never mix the used and new battery up for use.
5. Never recharge the uncharged battery.
GUARANTY OF THE PRODUCTS
Our products have been examined strictly. If not the contrived factors for
product’s damaged, please contact our company or sellers. It is important
that any users must be responsible for any loss and injuries because of
your wrong operations. For a novice, if you want to ask some helps with
installation or test or our product, please contact the sellers. We will work
for your warmly and sincerely.
Congratulation! After you finish above installation and test process, the
model had been set up already and you could enjoy your model. Besides
we will improve and update our products (SMARTECH serial, products)
4
continusly, we only need ask for the new information and new product’s
contents.
We hope our best products of radio controller can make a lot of
enjoyment in your life.
FCC STATEMENT:
“Modifications not authorized by the manufacturer may void users authority to
operate this device”
NOTE:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.