Petmate Le Bistro Users Manual

: Petmate Petmate-Petmate-Le-Bistro-Users-Manual-771789 petmate-petmate-le-bistro-users-manual-771789 petmate pdf

Open the PDF directly: View PDF .
Page Count: 3

Download
Open PDF In Browser	View PDF

le
bistro
portion control feeder
®

instructions
ASSEMBLY INSTRUCTIONS:
A. T
 o Assemble Hopper on Base:
1) Align hopper with base.
2) Insert hopper into base.
3) Twist and lock into place.
B. To Assemble Lid on Hopper:
1) Line up arrows on hopper with arrows on lid.
2) Place lid on top of hopper.
3) Twist and lock lid into place.
C. To Assemble Bowl into Base:
1) Insert bowl into base.
2) Lower bowl into base connecting hooks into the base.
(Make sure Portion Control LeBistro® is placed on an even surface)

Locking Lid
Alignment
Arrows
Hopper
Low Battery Light
Base
Food Chute
Removable Bowl

Lift Handles

SPECIFICATIONS:
Programming
• Up to three different sized Meals per 24 hours.
• Each Meal Serving is adjustable in 1/4 cup increments. Each Meal can be set from 1/4 cup
to 3 cups.
• Default Meal Servings are: Breakfast at 6:00 a.m. Lunch at 12:00 p.m. and Dinner at 6:00
p.m. All Meals are preset for 1/2 cups.
Dimensions
15.75”L x 10”Wx 18”H (assembled)
Capacity
• Hopper (alone) will hold 8.55 Ibs of typical variety of dry food.
• Base unit fully loaded, bowl and food wheel will hold additional 1.55 Ibs.
Wheel Dispensing Capacity
• 1/4 Cup increments or 1 Cup per complete revolution.
OverallWeight
•Weight: 3.5 Ibs (assembled without batteries and food).
Power
• Requires THREE “D” size batteries. Batteries NOT included.
• Use only alkaline batteries.
• Estimated life of one set of batteries is 6 months or less.
Note: DC Power Converter available as an accessory and can be ordered online at
www.petmate.com
Types of Food
• Dry dog or cat food only.
• Do NOT use canned food. Do NOT use moist dog or cat food.
• Do NOT use semimoist food. Do NOT use treats.

follow us online
petmate.com

Doskocil Manufacturing Company, Inc. dba Petmate • PO Box 1246, Arlington, TX 76004-1246
1-877-PETMATE • www.petmate.com
© Doskocil Manufacturing Company, Inc. 2010

Control Panel

Close up of Twist
and Lock Hopper
on Base.

Close up of Bowl
hook into Base.

PROGRAMMING

READ ALL INSTRUCTIONS BEFORE OPERATING THE PRODUCT.
A. To Install Batteries:
1) Turn the base upside down and remove battery cover.
2) Install 3 new “D” cell, alkaline batteries.
(Be sure to match positive and negative markings).
3) Replace battery cover. Be sure to “snap” in place.
To Turn Unit ON:
1) Press the (-) side of the On/Off switch DOWN. (located on the bottom of the base)
2) Set unit right side up. (LCD screen should be facing you
NOTE: Clock will flash “12:00 A.M.” automatically.
3) Press ENTER button to set current time. First the HOUR will be flashing.
4) Use UP or DOWN arrow buttons to set current HOUR. (until it is correct)
NOTE: the clock will automatically change to A.M. or P.M. as you scroll through the hours.
5) Press ENTER button again and the MINUTES will start flashing.
6) Use UP or DOWN arrow buttons to set current MINUTES.
7) Press ENTER upon completion.
NOTE: Clock will be set after setting minutes and the unit is now in AUTOMATIC MODE.
While setting current time, if the programming is not completed the Portion Control LeBistro® waits until the current time is
set and will not go into AUTOMATIC MODE.
SETTING ANY MEAL, MEAL TIME and MEAL SIZE:
B. To Set Meal Selection:
1) Press and Hold the ENTER button for 2 seconds. “MEALS” will flash.
2) Use UP or DOWN arrow buttons to select the desired Meal to be programmed. (Breakfast, Lunch or Dinner will flash as
UP and DOWN arrows buttons are pressed)
3) Press the ENTER button after you select the Meal.
a) “ Yes” will Flash. Press the ENTER if you want to set the meal time.
b) If you do not wish to set that meal time, press the DOWN arrow to select “No” and press ENTER.
Note: (if “No” is selected, press ENTER and the software takes you back to “MEALS”. Use UP or DOWN arrows buttons
to select the desired Meal to be programmed)

On/Off
Switch

A

Battery
Casing

B

Time must be set before
setup can continue

C

To Set Meal Time:
After selecting the MEAL to be programmed and selecting “Yes”, the HOUR will flash.
1) Use UP or DOWN arrow buttons to set Meal HOUR. (until it is correct)
NOTE: that clock will automatically change to A.M. or P.M. as you scroll through the Hours.
2) Press ENTER button again and the MINUTES will start flashing.
3) Use UP or DOWN arrow buttons to set Meal MINUTES.
4) Press Enter button when minutes are set.
The Menu will automatically take you to the “Meal Size” programming.
To Set Meal Size:
After setting Meal Time, the “Meal Size” Menu will flash. (right side of display)
1) Use UP or DOWN arrow buttons to increase or decrease amount of food to be dispensed. For example; to feed 1 cup
meal size, press the UP arrow button until 4 bars are displayed.
2) Press Enter upon completion. NOTE: Each bar equals approximately 1/4 cup. Themaximummeal size youmay select
is 3 cups.

Press Up or Down Arrows to
Program Meal Size

Meal Served counts up
to 99, then resets

D

C. To Set Other Meals:
After any Meal has been programmed (inclusive of time and size) “MEALS” will flash and Meals programmed will show
on screen.
1) Clock will display current time.
2) R
 EPEAT “Meal Selection” programming directions. NOTE: if you only wish to set 1 Meal, press ENTER while “MEALS” is
flashing and unit will go into AUTOMATIC MODE.
PROGRAMMING COMPLETE
After all meals are set:
1) Press ENTER
NOTE: After programming of all meals in completed, press ENTER while “MEALS” is flashing and unit will go into
Automatic Mode.
D. Meals Served
“SERVED” will show on screen at all times. This indicates number of Meals served. 1 digit equals 1 meal. Meals served
will go up to 99 and then reset at 00. To reset the “SERVED” counter; press UP and DOWN Arrow buttons simultaneously
and it will reset to 00. Meal Served counts up to 99, then resets
E. Manual Feed Option
Press and hold UP Arrow button for 3 seconds.
NOTE: Food will be dispensed according to first Meal set (i.e. breakfast is set at 1/2 cup, then food will be dispensed in
1/2 cup increments) Repeat if additional food is desired.

E

Hold for Manual Feed Option

F. Replacement of Batteries/Power
• When the “LOW BATTERY” warning light is on OR before leaving for an extended period of time, replace the batteries.
• Refer to “TO INSTALL BATTERIES” for directions.
• Once NEWbatteries are installed, turn unit ON.
• Set clock to current time.
IMPORTANT: Meal Programming is stored and will NOT need to be reprogrammed after batteries are replaced.
CLEANING
To Remove Bowl:
1) Place fingers under bowl and lift Bowl up.
2) Pull Bowl out horizontally removing it from the Base. (Bowl is top rack dishwasher safe)
NOTE: Lid and Hopper may be removed for cleaning. Hand clean with soft cloth and hand dry.
Warning:
Base unit should not be submerged in water at any time, this may damage electronic components. Do not place Base,
Hopper or Lid in an automatic dishwasher.
Allow parts to dry completely before adding new food.
Default Settings:
1. While setting “Time” during the “Initial Setup”; if the programming is not completed the Portion Control LeBistro® waits
for you to finish.
2. While setting the “Time” during the “Change Time” is not completed and no button depressed for 10 seconds the
Portion Control LeBistro® abandons the change and goes into “Automatic Mode” retains the previous “Time”.
3. While setting the “Meals” during the “Initial SetUp”
if no buttons are depressed for 10 seconds the Portion Control LeBistro® abandons the change and goes into “Automatic
Mode” retaining the previous “Meals” settings.
4. While setting the “Meals” during the “Change Meals” no buttons are depressed for 10 seconds the Portion Control
LeBistro® abandons the change and goes into “Automatic Mode” retaining the previous “Meals” settings.
CAUTIONS
Save these instructions for future reference. Read all instructions before operating product.
• For indoor use only.
• For dry food use only.Works best with ?”diameter food.
•N
 OT recommended for puppies or kittens less than 7 months old.
• Do NOT use this feeder with puppies or kittens not able to reach the feeding dish.
• Do NOT use this feeder with puppies, kittens, dogs or cats with any physical disability.
• Intended for use with dogs or cats only.
• Do NOT allow small children to play with, in or around feeder.
• Before leaving for extended time, always replace batteries with 3 new, “D” size batteries.
• Do NOT immerse control panel base in water.
• Do NOT place any foreign object in the feeder.
• Do NOT operate feeder without hopper and hopper lid securely in place.
• Feeder should be placed on a level surface.
• Do NOT disassemble feeder other than bowl, hopper, hopper lid and battery cover.
• Dispose of all packaging material properly. Some items may be packed in poly bags; these bags could cause suffocation;
keep away from children and pets.
• Check the low battery light frequently to be sure the feeder is dispensing properly.
WARNING
• Do NOT place anything on top of feeder. Unit starts automatically. Keep Clear.
• Base unit should NOT be submerged in water at any time, this may damage electronic components.
TROUBLESHOOTING
1) If no display is showing, turn on power. Refer to “To Turn Unit On” in programming instructions for specifications.
2) If
 the clock is flashing, the unit has lost its power and current time setting.
a. Reset current time.
NOTE: all previous meal programming does not need to be reset.
3) If “MEALS” is flashing, this indicates the unit did not completely deliver the full amount of food programmed for the meal.
a.Turn unit off, empty the hopper and disassemble the hopper from the base.
b. Check for food jamming in the throat of the base.
c. Dislodge food jam.
d. Reassemble unit.
e. Turn unit on and reset current time.
4) If the “Low Battery” indicator light is lit:
a. Turn unit off.
b. Replace the batteries.
c. Turn the unit back on and set current time.
NOTE: Meal programming remains and does not need to be reprogrammed.

F

Low BatteryWarning Light

PET TRAINING TIPS
Getting Your Pet Used
To The New Automatic
Feeder
Some pets may require a special
adjustment period to acclimate
to their new automatic feeder.
If you determine that your dog
or cat may require a special
adjustment period, use the
following steps:
1) Place the Portion Control
LeBistro® next to your pet’s
existing bowl or feeder. (Do
not turn the power on)
2) Place food in the bowl of the
Portion Control LeBistro®
(only for a period of time to
allow adjustment)
3) Keep food in the pet’s current
bowl. (only for a period of time
to allow adjustment)
4) Once you have observed
your pet eating from the
Portion Control LeBistro®,
remove their old feeding dish
and begin using the Portion
Control LeBistro®.
NOTE: Adjustment time for
the pet could be as short as a
day or as long as a couple of
weeks, depending on your pet’s
personality. You may also want to
introduce your pet to the Portion
Control LeBistro® by placing
small treats in the bowl.
REPLACEMENT PARTS
AC Adapter for U.S. and Europe
available at www.petmate.com
Replacement Bowls available at
www.petmate.com
Replacement Hoppers available
at www.petmate.com
WARRANTY
1 Year Limited
COUNTRY OF ORIGIN
All parts made and assembled in
China. All packaging made and
printed in China.



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.0-c060 61.134777, 2010/02/12-17:32:00
Instance ID                     : uuid:c54a8c2f-9b9c-344d-92a0-66c3012ee93e
Document ID                     : adobe:docid:indd:5f1c6e24-549d-11e0-a421-b8d70d897024
Rendition Class                 : proof:pdf
Derived From Instance ID        : e33d1692-02d0-11e0-93e7-dec30a8ea085
Derived From Document ID        : adobe:docid:indd:e33d168f-02d0-11e0-93e7-dec30a8ea085
Create Date                     : 2011:03:30 09:24:49-05:00
Modify Date                     : 2011:03:30 09:24:54-05:00
Metadata Date                   : 2011:03:30 09:24:54-05:00
Creator Tool                    : Adobe InDesign CS5 (7.0.3)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 12739 bytes, use -b option to extract)
Format                          : application/pdf
Producer                        : Adobe PDF Library 9.9
Trapped                         : False
Page Count                      : 3
Creator                         : Adobe InDesign CS5 (7.0.3)

EXIF Metadata provided by EXIF.tools