Peugeot Fb 0 1 2 4 Users Manual 753784

FB-0-1-2-4 to the manual 2ea1a264-c0eb-45a8-a1cc-c962b313cf38

2015-01-05

: Peugeot Peugeot-Fb-0-1-2-4-Users-Manual-203872 peugeot-fb-0-1-2-4-users-manual-203872 peugeot pdf

Open the PDF directly: View PDF PDF.
Page Count: 26

DownloadPeugeot Peugeot-Fb-0-1-2-4-Users-Manual- 753784  Peugeot-fb-0-1-2-4-users-manual
Open PDF In BrowserView PDF
WORKSHOP MANUAL 50 cm3
Motor FB-0-1-2-4

GB

CONTENTS

CYCLE PART

ENGINE PART
Designation

Page

- Contents, .............................................................
- Main characteristics, ............................................
- Maintenance plan, ................................................
- Putting into service, .............................................
- Special tools,........................................................
- Tightening torques ...............................................

1
2
3
4
5
5

Designation

Page

- Contents, .............................................................. 1
- Main characteristics, ............................................ 2
- Maintenance plan, ................................................ 3
- Putting into service, .............................................. 4
- Tightening torques, ............................................... 5
- Disc brake ........................................................... 14

Dismantling
Designtation

Page

- Removing the engine from the vehicle, ............... 6
- Placing the engine on the support, ...................... 6
- Removing the cooling system, ............................. 6
- Removing the flywheel, ........................................ 6
- Removing the oil pump, ....................................... 7
- Removing the starter motor, ................................. 7
- Removing the carburettor and choke, ................. 7
- Removing the intake valve and connecting part, . 7
- Removing the complete primary drive assy, ........ 7
- Removing the kick starter system, ....................... 8
- Removing the relay unit, ...................................... 8
- Removing the cylinder head, ............................... 8
- Removing the cylinder piston assy,...................... 9
- Removing the RH housing, .................................. 9
- Removing the crankshaft from the LH housing, .. 9
- Replacing the crankshaft bearings and seals,.. .... 9
- Checking the crankshaft ...................................... 9

Designation

Page

- Spark plug ............................................................. 2
- Fuel ...................................................................... 4
- Separate lubrication .............................................. 4
- Relay unit ............................................................. 4

ELECTRIC EQUIPMENT

Refitting
Designation

RECOMMENDATIONS

Page

- Refitting the crankshaft, ..................................... 10
- Closing the engine housings, ............................. 10
- Refitting the piston, ............................................ 10
- Refitting the cylinder, ......................................... 11
- Refitting the cylinder head, ................................ 11
- Refitting the relay unit, ........................................ 11
- Refitting the kick starter system, ........................ 12
- Checking the driven pulley clutch, ..................... 12
- Checking the drive pulley variator, ..................... 12
- Refitting the primary drive, ................................. 12
- Refitting the intake valve and connecting part, .. 13
- Refitting the carburettor, .................................... 13
- Refitting the starter motor, ................................. 13
- Refitting the oil pump and setting, ..................... 14
- Refitting the flywheel, ......................................... 14
- Refitting the cooling system ............................... 14

Designation

Page

- Electronic ignition, ............................................... 15
- Circuits supplied with alternative current, ........... 15
. lighting, ............................................................. 15
. choke, .............................................................. 16
- Resistance check of stator, ................................ 16
- Circuits supplied with direct current, .................. 17
. battery charge, ................................................. 17
. fuel gauge, ........................................................ 18
. oil gauge, ......................................................... 18
. horn, .................................................................. 18
. indicators, .......................................................... 18
. starter motor circuits, ....................................... 19
- Functional diagrams for electric circuits,. 20 and 21
- Key to electric circuits ........................................ 22

Trekker - Squab

1

TECHNICAL DATAS
Main spécifications

Frame

ENGINE MARKING

IDENTIFICATION MARK

Number
Type

XXXXXXXX
FB2

Identification
plate

FB2 ENGINE
Forced-air cooled 2 stroke engine :
- Bore and stroke : ................................................ 40 x 39.1
- Cylinder capacity : ............................................. 49.13cm3
- Compression ratio : ................................................... 6.6:1
- Maximum power (ISO) : .......................................... 3.1 kw
Distribution :
- Exhaust port : ........................................................... 160c°
- Scavenging port : ....................................................... 110°
- Air intake : ..................................... by reed valve induction
- Ignition : ....................... CDI (capacitive-discharge ignition)
- Spark advance : ....................................... 13° before TDC
- Spark plug ................................................... Resistive 5KÙ
..................................................................... NGK - BR7HS
.................................................................. EYQUEM R 850
................................................................. BOSCH WR4AC
- spark plug gap : ..................................................... 0.6mm
Carburettor : .......................................... GURTNER PA350
- Idling speed : .................................... 1800 rpm ± 1 00 rpm
- Initial position of the pilot air adjusting screw :
- Anticlockwise rotation : ..................................... 1/2 to 13/4
- Needle with 3 levels : .................................. clips at the top
- Main jet : ........................................................................ 74
Flywheel magneto :
- Number of poles : ............................................................ 6
- Power : .......................................................... 2500t = 55w
........................................................................ 5000t = 85w
Starter.motor : .................................................... MITSUBA
................................................................ 2000w SM10 129
................................................................. 1500w SM10254
Oil pump : .............................................................. MIKUNI
flow 24cm3 ± 1.7cm3 / hour at 3800 rpm, wide open
throttle. 1CM3 = 0.031 cubic inch

Identification : VGAS1A . . . . . . . . . . .
- Front tyre : ...................................................... 120/90 x 10
- Rear tyre : ...................................................... 130/90 x 10
Pressure :
- Front : .................................................................... 1,3 bar
- Rear : .................................................................... 1,6 bar

Capacities
- Fuel tank : .............................................................. 6 litres
- Oil tank : .............................................................. 1.3 litres
- Transmission case : ............................................ 0.12 litre
- Under-seat storage compartment : ............................. 3 kg

Dimensions
- Overall length : .................................................... 1760mm
- Overail width : ........................................................ 670mm
Excluding rear view mirror :
Overall height : ...................................................... 1110mm
Excluding rear view mirror :
Wheelbase : .......................................................... 1250mm

Weight
- Complete vehicle dry weight : .................................... 82kg
- Vehicie weight with tanks full : ................................... 88kg

Transmission
- Clutch : .................................... centrifugai, automatic type
- Primary réduction gear : ........................ by a ribbed V-beit
- Life of belt : ...................................................... 1 0 000 km
- Reducer equipped with 2 gearsets.

2

Markings 49cc
- Left hand casing (under the starter motor)
- Cylinder head (front right)
- Cylinder (exhaust flange left hand side)
- Intake pipe (on the front «49»)

Trekker - Squab

MAINTENANCE
MAINTENANCE PLAN
Depending on how the scooter is used, it is recommended to apply either

- The normal maintenance plan or
- The reinforced maintenance plan.

The normal maintenance plan includes:
- Visit at 500 km or 3 months
Plan A
- Periodic maintenance every 5000 km
Plan B
- Periodic maintenance every 10000 km
Plan C
The reinforced maintenance plan includes:
- Visit at 500 km
Plan A
- Periodic maintenance every 2500 km
Plan B
- Periodic maintenance every 5000 km
Plan C
The reinforced maintenance is intended for vehicles used in so-called “severe” conditions: door to door sales, intensive urban
use (courrier), short journeys engine cold, areas with dusty atmospheres, frequent use of vehicles at an ambient temperature
above 30°C.

PLAN A
500 km or 3 mois

PLAN B
5000 km or 2500 km*

PLAN C
10000 km or 5000 km*

X
X
X
X
X
X
X
X
X

X
X
X
X
X
X
X
X

X
X
X
X
X
X
X
X

X
X
X
X

X
X
X
X

CHECK :
Idle speed adjustment
Throttle
Oil pump control
Functioning of the electric equipment
Front and rear brake control
Fuel pipes
Oil pipes
Front brake fluid pipes
State and pressure of tyres
State, pressure and wear of tyres
Brake fluid level
Level of battery electrolyte
Tightening of nuts and bolts

X
X
X

REPLACE :
Relay unit oil
Spark plug
Filter element of the intake silencer
Front brake pads (if necessary)
Rear brake linings (if necessary)
Drive pulley rollers (if necessary)
Transmission belt

X
X
X
X
X

X
X
X
X
X
X
X

CHECK AND UNCLOG
Piston
Cylinder head
Exhaust port

X
X
X

CHECK AND LUBRICATE
Driven pulley :
movable driven face and needle bearing
Drive pulley :
movable drive face and rollers
Kick : driven gear and link ring

X
X
X

CLEAN AND ADJUST
Carburettor

X

VEHICLE TEST
Road test

X

X

X

* reforced maintenance

Trekker - Squab

3

INSTRUCTIONS FOR MAKING OPERATIONAL

1. Preparation of the battery
(dry charged)
- Remove the battery.
- Remove the six cell caps and the breather tube cap.
- Fill the battery with électrolyte up to the level marked
UPPER LEVEL (35% sulphuric acid 1.28 g/CM3),
Ref : ........................................................... 1 litre : 752740
................................................................ 5 litres : 752741
- Leave the battery to settle for half an hour. Top up the
level if necessary.
- Charge the battery for 1 to 2 hours with a current of
400m.A (0.4A).
- Replace the battery and connect the breather tube.
- Connect up the red positive leads to the battery positive
terminal, then the green negative lead to the battery earth
terminal.
- From then on, the battery can be topped up if necessary,
using distilled water only.

2. Fuel
Capacity : .............................................................. 6 litres
- Conventional 4-star petrol.
- Lead free petrol 98 octanes.

4. Putting fuel and oil circuits into
opération:
- Put one litre of fuel mixture with 4% oil into the fuel tank.
- Fill up the oil tank.
- Start the engine: make sure that the oil circuit is
completely primed. Remove the oil bleed screw from the
pump to allow air in the circuit to escape. When a
continuons stream of oil issues from this hole, replace the
bleed screw with its fiber washer.
For this : disconnect the oil intake hose to the carburettor
and check that it drips, frequency depending on the
engine’s speed.
- Top up the fuel tank with pure 4 star petrol.

5. Checking the oil level in the
transmission case:
- Unscrew and remove the oil filler hole screw A and
make sure that the oil level is flush with the level of the
filling hole. The vehicle must be positioned on its stand
and on a level surface.
Esso Oil SAE 80 W 90
REF : .................................................................... 753009
capacity 0. 1 2 litre
A = 1.2m.daN.

3. Separate lubrication:
Capacity : .......................................................... 1.3 litres.
- Fill up the oil tank with semi-synthetic engine oil for 2stroke engines with separate lubrication,
- Type TC (API standard), type TSC3 (ASTM standard), - Type FC (JASO standard) or a synthetic oil.
PEUGEOT MOTOCYCLES recommends :
....................................... ESSO : 2T Special performance
......................................................... ESSO : 2T Synthetic

4

6. Checks before delivery to the
customer:
- In particular, check the tightening of the Wheel nuts ... front : .................................................................... 6m daN
- rear : .............................................................. 1Om daN
- Check the tightness of the nuts and bolts.
- Check brake adjustment and eff iciency.
- Cold tyre pressure:
FRONT
- pressure : ......................................................... 1.3 bar
- size : .......................................................... 120/90 x 10
REAR
- pressure : ......................................................... 1.6 bar
- size : .......................................................... 130/90 x 10
- Make sure all lights and signals operate correctly
(taillight, turnsignals, stop light, horn), and various
warning lights.
- vehicle road test.

Trekker - Squab

TIGHTENING TORQUES AND SPECIAL TOOLS

TIGHTENING TORQUES

SPECIAL TOOLS

Assembly screws for :
- Housings : ........................................................ 1m.daN
- Covers : ............................................................ 1m.daN
- Intake connecting part : .................................... 1m.daN
- Starter motor : .................................................. 1m.daN
- Stator : .............................................................. 1m.daN
- Sensor : ............................................................ 1m.daN
- Fan : ................................................................. 1m.daN
- Carburettor : .................................................. 0.8m.daN
- Oil pump : ...................................................... 0.8m.daN
- Cylinder head : .............................................. 1.2m.daN
- Drive pulley : ..................................................... 4m.daN
- Driven pulley : ................................................ 4.5m.daN
- Rotor : .............................................................. 4m.daN
- Oil plug : ........................................................ 1.2m.daN
- Spark plug : ...................................................... 2m.daN

- Service cradle mount ............................................... 64765
- Adjustable adapter for engine service cradle ......... 752026
- Flywheel holder ....................................................... 68570
- Snap ring pliers ..................................................... 752000
- Protective end, small model for flywheel magneto remover
.................................................................................. 68007
- Puiler tool ................................................................ 64706
- Crankshaft end protector ......................................... 69098
- Shouldered centring tool .......................................... 64710
- Screw on torque handle ........................................... 69104
- Compresser tool, ail types of clutch ....................... 752127
- Tubular socket wrench 39 ..................................... 752361
- Adjustable pin type face wrench ............................ 752237
- Set of half sheils 0 52 .............................................. 64709
- Puiler tool .............................................................. 750807
- Support washer ..................................................... 750808
- Surface plate 250 x 160 x 50 ................................. 750541
- Comparator (adapts to pattern plate accessory ..... 750969
- Torque wrench + extension + reducer ..................... 69802
- Flywheel puller supplied with 68007 protector ....... 750806
- Blooking tool .......................................................... 752370
- Pliers for circlips ...................................................... 69117
- Spindle .................................................................. 750069
- Steering tools ........................................................ 752948

Engine

Frame
- Front wheel axis nut : ........................................ 6m.daN
- Rear wheel nut : ............................................. 10m.da N
- Engine joint on rod : ........................................... 6m.daN
- Rod joint on chassis : ..................................... 2.2m.daN
- Rear shock absorber upper fixation : .............. 1.6m.daN
- Rear shock absorber lower fixation : .............. 1.6m.daN
- Exhaust nuts on cylinder : .............................. 1.6m.daN
- Handlebar nut : .................................................. 4m.daN
- Steering lock nut : .............................................. 7m.daN

Standard
- Screw and nut ø 5mm : ...................... 0.45 to 0.6m.daN
- Screw and nut ø 6mm : ........................ 0.8 to 1.2m.daN
- Screw and nut ø 8mm : ........................ 1.8 to 2.5m.daN
- Screw and nut ø 1Omm : ........................... 3 to 4m.daN
- Screw and nut ø 12mm : ............................ 5 to 6m.daN

Trekker - Squab

5

REMOVAL
Removal of the engine

Removal of cooling
systern

Removal of the flywheel
magneto

- Remove :
- All side casings

- Remove the two parts of the fan
covers (4 screws).

- Disconnect :

- Block the rotor using a notch type pin
752237.

- Fuel line from the carburettor,
- Fuel tap vacuum hose,
- Oil pump control cable
- Throttle control cable,
- Oil iniet piping at the pump (large
hose)
- Radio interference suppressor cap
- Rear brake control cable

Disconnect :
- The wiring harness on the frame’s
right tube: located at the outlet of the
Flywheel magneto (under the foot
board), choke, starter motor.
- Remove the nut (right-hand thread).
- Fit the crankshaft end protector
68007 onto the end of the crankshaft.

Remove :
- The lower anchor bolt of the shock
absorber and the front anchor pin of
the engine.

750806
68007

Fitting of engine on service
cradle

64765

- Remove the 4 fastening screws of
the fan and remove the fan.
- Screw the flywheel puller tool 750806
onto the rotor and tighten the centre
bolt until the rotor comes away.
- Remove the 2 fastening screws of
the sensor, as well as the 2 fastening
screws of the stator plate.

752026

- Place the engine onto the adapter
752026
- Place the assembly on the cradle
mount 64765 clamped in a vice

- Remove the coil assembly and the
sensor.

6

Trekker - Squab

REMOVAL
Removal of the oil pump

Removal of the primary
drive system
You do not have to remove of the kick
starter arm when removing the
crankcase cover.
- Loosen and remove the 11 fastening
screws of the cover.

- Unclip the oil inlet pipe to the
carburettor.
- Unscrew the 2 hex head socket
screws.
- Remove the oil pump and the control
flange.
- Remove the 2 square fastening nuts
Q from their housings.
- Remove the flexible washer lodged
between the pump and the shaft
bearing of the oil pump.

Removal of the
carburettor / choke
assembly
- Take off the 2 fastening screws from
the carburettor and remover the
carburettor / choke
assembly, as well as the isothermal
spacer.

- Remove the cover with both locating
dowls.

- Remove the starter drive assembly
from the starter motor.

- Adjustment: see page N° 14

Rernoval of the starter
motor

Removal of the reed
valve and intake pipe
- Unscrew and remove the 4 fastening
screws.
- Remove the intake pipe, the gasket,
the reed valve assembly and the
second gasket.

- Hold the starter ring gear with the
tool 752370.
752370

- Free the wire harness from the
support bracket.
- Remove the 2 fastening screws and
washers from the starter motor and
pull out together with «0» ring seal.

Trekker - Squab

7

REMOVAL
Make careful note of where this tool
comes level with the starter ring gear
plate of the starter motor in order to
make sure, when refitting, that the
pressure plate fits correcte into the
grooves of the crankshaft.
- Loosen the fastening nut (right-hand
thread) of the gear plate of the drive
pulley.
- Remove the nut, washer and plate.
- Remove the belt.
- Remove the drive pulley assembly
(variable speed drive) and the washer
on the engine housing side (12,35 X
19,75 X 1).

Removal of the kick
starter system
- Actuate the kick starter spindle with
your thumb and remove the drive
ratchet and its washer.

- Remove the kickstarter lever. Using
snipe-nosed pliers (ref. 69117), take
off the circlips, the washer, then
remove the kick starter toothed
section, the pull-back spring and the
bushing.

- Removal of the drive shaft (or input
shaft) from the transmission cover is
done using a mallet.
- Remove the thrust washer from the
counter shaft (14.3x26xO.5).

- Drain the transmission case
completely before removing the final
shaft (or output shaft) in order to avoid
contamining brake linings.
- Pull out the final shaft (output shaft).

Rdl 12,35x19,75x1

- Pull out the countershaft as well as
its friction washers (1 4.3 x 26 x 0.5)
and flexible washer (1 4 x 22 x 1.5).

- Block the clutch drum with the flywheel pinch bolt no.68570 or the adjustable pin type face wrench 752237.

Dismantling the
transmission case
After draining the transmission case:
- Remove the 5 screws securing the
cover.

752237

Removing the cylinder
head

- Loosen the screw, remove the drum
and the clutch driven pulley assembly.

8

- Unscrew in a crosswise order the 4
screws securing the cylinder head and
cylinder block assembly.
- Remove the cylinder head and
gasket.
- Remove the cover with the drive
shaft (or input shaft), the gasket and
both locating dowls.

Trekker - Squab

REMOVAL
Removing the cylinder
and piston
- Remove the cylinder and cylinder-tocrankcase gasket.
- Pack the crankcase mouth with
clean cloth or paper.

- Turn the inner thrust bolt of tool
750807 until the crankcase halves
split Hold the connecting rod so that it
does not knock against the crankcase
halves.
- Remove the RH half casing.

- Remove the gasket and both
locating dowls. Remove the drive
shaft of the oil pump and its locating
bush.

- Secure the plate to the crankcage by
tightening the 4 screws.
- Withdraw the crankshaft by turning
the inner thrust bolt of tool 64706.

Changing the bearings
and seals
- Heat the crankcase halves evenly to
90° so that they expand. The bearings
will drop out, drive out the seals.
- Fit the new bearings while the
crankcase halves are still warm.
- Fit the oil seals in place.
- The oil seal on the drive pulley side
should fit flush with the crankcase, the
lips being on the fl.ywheel housing
side. The seal on the flywheel side
should be approximately 9mm in.

- Lean the engine to the left and take
out the wrist pin’s RH snap ring.
- Push the wrist pin from the left to the
right; this opération does not require
use of a strap.
- Take out the needie bearing race.

Opening the crankcase

Note:
If the crankshaft bearings remain on
the crankshaft; use the puller tool
64706 with the half shells 64709 (diam
= 52) to remove them. Do not forget
to fit the crankshaft end protector
69098 onto the ends of the crankshaft.

- Remove the 6 screws securing the
RH crankcase half.

Removing the crankshaft
assembly
- Fit the crankshaft end protector
69098 onto the end of the crankshaft.
- Fit the crankshaft end protector
68007 onto the end of the crankshaft.
- Position the puller tool 750807 onto
the crankcase half.

Checking the crankshaft
assembly

64706
752168

750807

69098

- The maximum side play of the
conrod big end should not exceed:
0.5mm.
- Check crankshaft alignement as
shown in the drawing (surface plate
750541, comparator 750969
The values measured at the ends
should not exceed 0.12mm.

-Fit puller tool 647706 with the plate
752168 onto the crankcase.

Trekker - Squab

9

REFITTING
Refitting the engine
Assembly of the crankshaft into the
left hand crankcase:
- Fit the crankshaft into the bearing.
- Screw the ex tended nut 750069
onto the end of the crankshaft.
64706

Closing the crankcase halves
- Position both locating dowls in the
LH crankcase:
- Put the crankcase gasket in place
(no oil, no grease).

Refitting the piston
- Check the cylinder and piston parts
are a matched pair.

752168
750069

- Fit tool 64706 with the plate 752168
onto the extended nut and centre the
assembly onto the crankcase using 4
screws.
- Position the centring tool 64710.

- Position the RH crankcase and fit it
on being careful not to damage the oil
seal where it meets the cotter key.
-Screw the extended nut 750069 onto
the end of the crankshaft.
- Position the washer 750808 (50 x 29
x 3mm).
-Position the tool 64706.

- Fit the needie bearing race into the
conrod small end after having oiled it
(2-stroke engine oil).

750808
69104

64710

- Position the piston with the arrow
pointing towards the exhaust port.
-Push in the wrist pin.
-Fit the snap rings. It is essentiel that
they are new.
- Screw the torque handie 69104 onto
the extended nut 750069 while
keeping the crankshaft assembly
steady. Continue turning the torque
handle until the crankshaft comes into
contact with the bearing.

Waming : do not jam the conrod

- Position the centring tool 64710.
- Turn the torque handle 69104 until
the crankcases close completely.
- Hold the crankshaft assembly steady
on the left hand side with the starter
ring gear.
- Grease the oil pump shaft and
position the shaft / seat assembly in
the crankcase.
- Make sure that the crankshaft
assembly can rotate normally and
drives the oil pump shaft correctly.
- Position the 6 fastening screws (3 =
L 45mm, 3 = L 70mm) and tighten
them to 1 m.dan.
Make sure the crankcase gasket is
level.

cabre in the crankcase.
In order to hold the crankshaft
assembly easily, use the rotor
positioned in its right hand side
woodruff key.
Make sure the crankshaft assembly is
correctly positioned in relation to the
crankcase mouth (the middle of the
conrod must correspond with the level
of the crankcase mouth).

10

Lubricate the crankshaft assembly
and bearings with 2-stroke engine oil.

Trekker - Squab

The opening of the snap ring will be
positioned at the top or at the bottom,
but under no
circumstances to the side.

REFITTING
Refitting the cylinder
- The parting face should be cleaned.
- Lubricate the piston and the cylinder
bore.
- Fit a new and dry cylinder base
gasket onto the cylinder.
- Make sure that the piston ring end
gaps are aligned with the positioning
slots.
- Position the cylinder and push it
down while squeezing the piston rings
bet-ween your thumb and middle
finger.
- Make sure the cylinder base gasket
is correctly positioned on the
crankcase using 2 threaded bolts.

Refitting the transmission
case
- Replace the oil seals and bearings if
necessary by the appropriate “ heating
and drift >, method.
- Check that the outlet channels are
clear :
Removal of the case.

Important
Smear the countershaft ends with
graphite grease in order to ensure
improved lubrication when putting the
vehicie into service.
- Position the countershaft.
- Position the final shaft (or output
shaft) while being careful not to
damage the oil seal.

If this seal is damaged, oit wîil flow to
the outside through the outiet siot
located in the retum
spring housing of the brake key; Photo
opposite.

Refitting the cylinder head
- Check thàt the gasket seat surface
of the cylinder head is not damaged.
-Position the 4 fastening screws onto
the cylinder head with washers.

- Fit a thrust washer 14.3 x 26 x 0.5
onto the countershaft;

Outlet between the oil seal and the
rear wheel bearing.
- Fit on the countershaft:
· the flexible washer 14 x 22 x 1.5
· the thrust washer 14.3 x 26 x 0.5.
- Position 2 locating dowls and the
gasket.
- Position the primary shaft (or input
shaft) into its bearing using a mallet if
necessary.
- Position the cover and secure it
using 5 screws (L = 40) 1 m.dan.

- Position the cylinder head gasket
onto the cylinder head, the raised face
upwards.
- Push the cylinder head / screw /
gasket assembly onto the cylinder.
- Tighten the 4 screws progressively
and in a crosswise order (L = 95mm)
1.2 m.dan.
côté couvercle

ARBRE INTERMÉDIAIRE

Make sure that the shafts can rotate.

Note

rondelle souple
rondelle métal

-Fit the spark plug 2m.daN.

Trekker - Squab

- Fill the case with 0.12 litre of SAE
80W 90 oil.
- Peugeot Motocycles recommends
ESSO GEAR OIL GX........ ref. 753009
- Oil filler screw 1.2m.daN.

11

REFITTING / FITTING
Instailing the kick starter (LH
cover)
- Fit the spindle bushing and the nylon
spacer (mark 1).
1

- Position the return spring, fit the
longest hook onto the pin on the cover.
- Instail the spindle into the bushing
after lubrication.
- Fit the second hook of the spring
onto the toothed section.
- Wind the spring slightly so as to
position the kick starter spindle onto
the central rib of the cover.
- Install the washer and circlips onto
the axis of the toothed section.
- Position the drive ratchet:
place the washer over the boss of the
ratchet shaft housing
load the kick starter by about 1/8 of a
turn in order to position the ratchet
(after lubricating the
shaft),
position the ratchet stop in its housing.
(Mark 2).

- Hold the assembly using tool 752127
in a vice and loosen the special nut
with the wrench 752361 (39) or a 34
mm wrench depending on the clutch.
- Remove in the followin’g order :
. the clutch shoe assembly
. the spring
. the spring guiding sleeve
. take out the three guide pins of the
variable speed drive,
. separate the movable driven face
from the fixed driven face.

2.

Refitting

- Check the oil seals of the movable
driven face.
- Assemble the fixed and movable
driven faces.
- Refit the 3 guide pins and lubricate
the ramp of the variable speed drive.
- Position the sleeve having checked
that both «0» rings are in good
condition.
- Position the spring and the clutch
assembly.
- Using the tool 752127, compress the
spring and check that the nut is
tightened to 5m.daN.

- After cleaning, check the rollers in
particular. Their diameter should not
show any flat spots.

3. Refitting
- Reverse opérations to dismantling
having lubricated the 6 rollers, the
ramp, and the movable
clutch plate bore with high
température grease 752093.
NOTE :
On the first generation FB engines
(Zenith, Buxy, Speedake), the rollers
of the drive pulley were assembled
without grease.

C. Refit the primary
transmission.
Fitting a variator
Warning: do not delete any piling up
element or reduce the dimensions.
This would lead to a tightening of the
nut on the grooves of the crankshaft
assembly and not on the fixes driven
face and hence would destroy the
crankshaft assembly.

B. Drive pulley - variator
assembly :

2

1. Dismantling
- Remove the thrust spacer L = 38mm
and the 3 bolts that secure the
housing and the stop (no 7 wrench).

PRIMARY
TRANSMISSION
A. Clutch and driven puiley
assembly :
1. Dismantling:
752361

- Remove the housing using a
screwdriver.
- Remove the stop, the ramp plate, the
3 plastic spacers and the 6 rollers, the
«0»ring (81/1.5).

2. Inspection

752127

12

Trekker - Squab

- Place the washer 12.35 x 19.75 X 1
on the crankshaft assembly.
- Position the variable speed drive
while keeping the movable driven
face, the 6 rollers and the variation
ramp with the thrust spacer under
pressure.
- Fit the drive belt.
- Position the start ring gear plate
while checking that it is properly fitted
on the grooves of the crankshaft assembly, position the nut and tighten by
hand.
- Check that the ring is flush with the
tool 752370.
- Tighten the nut to 4m.da.N.

FITTI NG
Fitting of the «clutch drive
pulley» assembly and the belt

Fitting the reed valve and
intake pipe

- Introduce the belt to the bottom of
the groove of the driven puiley by
pulling apart the drive faces using both
hands.
- Position the belt on the drive pulley.
- Fit the «clutch / drive pulley»
assembly onto the primary shaft of the
transmission.
- Position the clutch casing and tighten
the nut to 4.5m.daN while holding it in
place with the
adjustable pin type face wrench
752237 (or the flywheel holder).

- Check:
the condition of the petals and the
seats.
- lnstall in the following order on the
crankcase:
a gasket
a reed valve
a gasket

- Fit the carburettor and tighten to 0.8
m.dan
Screw 1: air screw
Initial adjustment: screw until it seats
without forcing, then loosen by 11/2 to
13/4 of a turn.
Screw 2: throttle stop screw (idle
speed: 1800 rpm ± 100 rpm).
Needle : clips at the top.

see
foolproof
device

2
1
- Fasten all the parts using 4 screws
(L = 28mm), and tighten to 1 m.dan.

Fitting the starter motor

NOTE
- The rollers must be checked every
50OOkm.
- The belt must be changed every
100OOkm.

Fitting the carburettor
Fitting the transmission
case

- Position the washer 8.5 x 16 x 0.8,
the kick starter gear assembly.
Grease its bearings.
- Position both dowel pins and the
transmission case using 1 1 screws.
Tighten to 1 m.dan.

- Position both carburettor holding
screws (L = 28 and 50mm) onto the
intake pipe.
- Position the isothermic spacer with
the seai on the intake pipe side. This
spacer is aimed at avoiding heat from
the engine being transferred to the
carburettor. A foolproof system on the
edge of the spacer guarantees that it
is positioned correctly (arrow pointing
towards the front).

- Install the starter motor with its «0»
ring.
- The lower screw also ensures
earthing of the battery to the engine
(green wire).
- The upper screw also ensures
fixation of the cable harness clamp.
- Tighten to 1 m.dan.

Good

No good

Trekker - Squab

13

FITTING
Fitting of the oil pump
- Position both square nuts (Q) in their
housings.
- Place the flexible washer on the seat.
- Position the pump fitted with its
«0»ring, position the sheath stop
fastening hook and fasten the cluster
with two n».4 hex head socket screws.
- tighten to 0.8m.daN.

Adjustment of the oil purnp
1) Check the free play in the throttle
grip (2 to 5mm) and adjust if
necessary using the adjusting screw.
2) Open the throttle fully.
-Check that the alignment mark on the
pump control lever is opposite the
mark on the pump body.

Bleed screw
Mark

- Disconnect the oil input hose on the
pump and check the oil flow. Check
also :
. that there is oil in the tank,
. that the hose is not trapped,
. that the oil filter is not blocked,
. that the tank filler hole is not
blocked (atmospheric pressure hole).
- Reconnect the hose onto the pump
body.
- Open the pump bleeding screw until
ail the air bubbles have escaped and
then close again.
- Turn the engine on.
Disconnect the oil input hose on the
carburettor. Check that the oil drips
out. Dripping frequency depends on
the engine’s speed
- Reconnect the hose onto the
carburettor. OIL PUMP FLOW: 24
cm3 ± 1.7cm3 hour at 3800 rpm.
Wide open throttle.

- Position the rotor.
- Keep the rotor in place using the adjustable pin type face wrench 752237.
- Tighten the nut at 4m.daN.

Fitting the cooling systern
- Position and fasten the fan onto the
rotor (4 screws L = 1 8). Tighten to 1
m.dan.
- Position and fasten the cylinder case
and cooling cover (4 screws M = 25).
Make sure that it is fastened correctly
around the sensor.
- Tighten to a torque of 1 m.dan.

Fitting the flywheel
- Position the stator / sensor assembly
on the crankcase.
- Fasten with 4 screws (2 screws L =
16, 2 screws L = 20). Tighten to 1
m.dan.

- Adjust if necessary by turning the
pump cable abjusting nuts.

Checking the lubrication
circuit
- Supply the carburettor from a
separate tank containing 2-stroke fuel
mixture.

- Make sure that the woodruff key is
indeed on the crankshaft.

PARTIE
CYCLECYCLE
PART
DISK BRAKE
Filling the circuit :
At the receiver (brake calliper),
remove the cap of the bleed screw.
Connect a flexible hose to this screw,
the other end put into an empty
container (fuel hose for example).
Loosen this bleed screw.
Remove the cover and seal, with the
tank positioned horizontally, f rom the
emitter (master cylinder). Fill the tank
with brake fluid. Activate the brake
handle gently until the liquid comes
through to the bleeding container.
Tighten the bleed screw.
Fill the emitter tank to the top.

14

Activate the brake lever several times
with the cover refitted.
Loosen the bleed screw again. Air
bubbles should escape through the
flexible hose.
When there are no more air bubbles,
tighten the bleed screw with the brake
lever constantly on.
Repeat the operation until no bubbles
appear in the liquid.
Note: At the end of the opération, top
up the level.
- It is sometimes necessary to tap the
elements of the brake system lightly in
order for the air to escape.
- Certain callipers need to be
dismounted in order to place the bleed
screw in the high position.

Trekker - Squab

Warning :
- The brake fluid attracts humidity.
ln certain conditions humidity may
impair braking efficiency. You must
always use brake fluid from a recently
opened container (tightness cap). The
liquid recovered in the bleed container
must not be reused. Do not open the
container when there is a high degree
of hi-imidity in the atmosphère (rain,
fog .... ).
- Brake fluid is corrosive. Avoid
spillage on painted parts.
- Do not spill fluid onto the pads or the
disks.
- Use brake fluid which complies with
the DOT 3 or DOT 4 standards.
(Lockeed D55 for exam

ELECTRIC EQUIPMENT
3

IGNITION

1

a

Operating principle :
The ignition coil charges a condenser
in the CDI unit. Passage of the rotor
pad in front of the sensor authorises
the discharging of the condenser in
the primary winding of the high voltage
coil via a thyristor, in order to generate
through transformation in the
secondary, a voltage in the region of
20 000 volts at the spark plug.

off
4

b

2
5

on
6

1

15
12V 4Ah

3

4

Troubleshooting :
- Check the connections, especially
the earth connection of the starter
motor.
- Check by successively replacing with
new components: the spark plug,
radio interference suppressor, high
voltage coil, CDI unit.
- Check the key switch.
Example of a breakdown: the engine
only runs with the rear brake applied.
Cause:
earth wire of the starter
motor is damaged.
The CDI unit, ref. 709205 is used on
all 50cc powered two-wheelers as well
as on the SV 80cc.

5 5kΩ
26

6 5kΩ

1 a
b
2 3 4 5 6 15 26 -

Warning :
A second CDI unit, ref. 705272
(marked CI 08) is reserved for SV 125
SC-SX models.

ALTERNATING CURRENT
POWERED CIRCUITS

Flywheel
- ignition
- sensor
Ignition switch
(CDI) ignition unit
High voltage coil
Interference suppresser 5 KW
Spark plug resistance 5 KW
Battery
Starter motor

9

LIGHTING AND STARTER
MOTOR
Operating principle:

13

6,7Ω 5w

8

A

B

3 x 1,2w

1,2w

15w

5,9Ω 30w

10

a

11

Three coils connected in series in the
flywheel magneto generate an
alternating current stabilised by the
regulator to give a maximum voltage
of 12V ± 0.5V.

LIGHTING

27 0,75Ω 4w

5/21w

7

15

12V 4Ah

c

1

When in the < lights off > position
(Day*), current is directed from the
switch towards a résistance of 5.9 Ù
30W where it is consumed (pink wire).
When in the “ lights on ” position
(night), current is supplied to the bulbs
(brown wire); headlight, taillight, instrument panel light, headlight telltale.

14

a

1 - Flywheel
c - alternative current
7 - Regulator
a - AC regulator
8 - Choke
9 - Resistance 6,7 W 5W
10 - Lighting control
11 - Resistance 5,9 W 30w
13 - Headlamp
A - Instrument panel lighting
B - Headlamp telltale
14 - Rear and stop light
15 - Battery
26 - Starter motor
27 - Current limiter

Trekker - Squab

26

15

ELECTRIC EQUIPMENT
Note :
The rear bulb is composed of 2
filaments, one 5W filament supplied
with alternating current for the taillight,
one 21 W filament supplied with direct
current for the stop light.

1/ Solving lighting faults
- Check the bulbs; power, voltage,
compliance with European standards
(El).
- Check the connections (especially
those of the regulator).
- Check the voltage
using a multimeter (MX40) set to the
AC voltmeter position.
check at the terminale of a bulb
(brown wire), that voltage does not
exceed 12 volts ± 0.5V when
accelerating the engine. If the voltage
is over 13V, check the regulator
connection (especially the green earth
wire). If necessary, change the
regulator (it is not possible to check
the regulator when static).

2/ Checking
Check the continuité capacities of the
three coils of the flywheel. Engine
stopped.
Lighting and starter: yellow wire and
earth wire = 0.4 ohm.

1

CHOKE

3

1. Operating principle

2

Cold starting: the choke is
automatically in opération: the
carburettor’s mixture enrichment
circuit is open.
As soon as the vehicle is switched on,
the heat résistance which is supplied
by the flywheel magneto causes the
continuons wax to expand in its
capsule. The diaphragm pushes the
master and intermediate pistons which
cause the air duct to the throttle valve
to close gradually and to progressively
block fuel flow with the needle. When
the engine is warm, with the ducts
blocked, the enriching circuit is not
operational.

4
5
6
7
8
9

14

10

13

11
12

2. Checking
- Average résistance value of the
choke alone - 5 ohms.
Note :
The résistance value varies depending
on résistance température: the colder
the température, the lower the
résistance value and vice versa.

1
2
3
4
5
6
7
8
9
10
11
12
13
14

-

Yellow wire
Green-black wire
Heating resistance (PTC)
Wax
Membrane
Intermediate fluid
Push piston
Return piston
Return spring
Air throttle valve
Needle
Needle well
Needle spring
“O” ring seal

Value flywheel control

750 Ω

0,7 Ω
d

a

1 - Flywheel
a - ignition
b - sensor
c - alternative current
d - battery charge current

b
c

1

0,4 Ω

16

Trekker - Squab

110 Ω

ELECTRIC EQUIPMENT
1 - Flywheel
c : alternative current
d : battery charge current
2 - Ignition switch
7 - Regulator, rectifier
b : regulator, rectifier (DC)
14 - Rear and stop light
15 - Battery
16 - 5A Fuse
17 - Horn
18 - Horn button
19 - Indicator control
21 - Indicator bulbs
D - Indicator telltale
22 - Fuel gauge
E - Fuel gauge receiver
23 - Stop contact switch
24 - Starter motor relay
25 - Starter motor control
26 - Starter motor
27 - Current limiter
28 - Low oil level contact switch
C - Low oil level telltale

DIRECT CURRENT POWERED CIRCUITS
CHARGING BATTERY - STARTER MOTOR - FUEL GAUGE OIL GAUGE - TURNSIGNAL LIGHTS - HORN
Operating principle:
In the flywheel, the three coils used for the alternating current circuits are
associated with two other coils to produce a regulated current increased to
14.5V ± 0.5V maximum by the current increasing regulator. (This time, its is the
second stage of the regulator which is used),

27

14

0,75Ω 4w

5/21w

7
b

5A

2

3

d

1

12V 4Ah

5

off

4

15

16

on

24

6

1

23

c

19

18

28

D

1,2w

17

25

20

26

E

C

22
10Ω

1,2w

21
4x 10w

100Ω
10/07/97

BATTERY CHARGING
This circuit consists of the following
elements connected in series: flywheel
magneto - regulator - fuse
- battery.
The voltage depends on the engine’s
speed.
While this voltage is lower than battery
voltage, it is the battery which supplies
the various circuits. As soon as this
voltage is higher than battery voltage,
it is the flywheel which supplies the
various circuits and recharges the

battery.
Putting the battery into service: see
maintenance page N° 3.

Checking the charge
Use a multimeter (MX40) set to the
DC voltmeter position (=) connected
to the terminale of the battery. Check
that the voltage varies depending on
the speed of rotation of the engine up
to a maximum of 14.5V ± 0.5V.
If the voltage at the battery terminale
exceeds 15V, the regulator is not
connected to earth or is faulty. If
there is no variation in voltage at the
battery terminale, check the fuse,

Trekker - Squab

connections, especiahy those of the
flywheel or regulator harnesses (loose
connections inversion of wires in the
connecter for example).

Checking a discharge
Engine off.
Disconnect the red wire from the
battery.
Use a multimeter (MX40) set in the
Ampmeter (1OA) position, connect the
black wire (COM) to the + terminal of
the battery and the red wire (1OA) to
the disconnected red wire of the
battery.

17

ELECTRIC EQUIPMENT
1. Key switch to OFF
No display should appear on the
multimeter. If a value is displayed (for
example 0.5mA), either the regulator
(connection wires) or the key switch is
faulty.

2. Key switch to ON
A slight discharge can be explained by
sending a volt supply to the fuel gauge
and to the oil low level
warning light (0.9mA to 1OOmA
maximum).
A significant dischar@e indicates a
more or less earthed circuit.
Disconnect the various circuits until
the discharge disappears and locate
either the defective unit or wire
(starter, motor, stop light, fuel gauge,
oil, indicator, horn, key switch or
instrument panel circuits).

Checking the capacities of the
flywheel magneto.
Battery charge (current = )
White wire = 0.7 ohm and earth.

check way N°1 on the 9-way main
connector.

HORN
Operating principle
Supplied with a continuons current, a
horn and a switch are fitted in series.

OIL GAUGE
Operating principle

Check :

Supplied with a continuons current.
The float acts like a switch; when it is
in a low position, it closes the circuit
which causes the warning light on the
instrument panel to come on.

- If the horn does not work, check the
circuit (fuse, key switch, left-hand grip
handie switch), in order to get 12 volts
at the horn terminals.
- Check that the horn is planned for
use with continuons current (presence
of an adjustment screw, here hidden
by a plug). Horn test

Checking :
If the bulb on the instrument panel
remains permanently on, check the
float.
If the bulb remains permanently on,
check the 4-way connector on the
instrument panel (terminal 4,
the blue / white wire must not receive
a 12 volt supply while the float is in
high position).

FUEL GAUGE
INDICATORS

Operating principle

Checks :
ignition to ON
If the fuel meter is permanently at
maximum level:
- Disconnect the gauge if the minimum
level appears, check the gauge.
- If the maximum level is still shown,
disconnect the 5-way connector on the
instrument panel. Check, using a multimeter (MX40), set in the ohm position, that the yellow / white wire is not
earthed. If this wire is earthed, check
the harness. If this wire is not earthed, change the instrument panel.
If the gauge indicator is permanently
at minimum level:
- Check that the tank gauge is
connected properly
- Check the capacities of this gauge (5
to 100 Ù)
- Check the 5-way connector on the
instrument panel: black wire to way
no.1, yellow/white wire to way N° 4.
- Check that the black wire receives a
12 volt continuons supply.
- Check that the yellow/white wire is
continuons up to the gauge. If not,

18

Operating principle
A direct current supplies the blinker
control unit located under the front
cover. This current is sent to the lefthand grip handle to be distributed by
the switch to the left-hand or righthand bulbs of the turnsignal lights.
The telltale on the instrument panel is
common to both sides. Its earth
return line is via the bulbs on the side
not used.

5A

2

3
1

12V 4Ah

5

off
4

15

16

on

Resistance from the fuel meter to the
tank varies depending on the level of
fuel from 10 to 100 ohms. On the instrument panel, the needle will vary according to this resistance from min. to
max. When the needle reaches the
reserve supply level, this indicates a
remaining riding range of about 25km.

6

19

Checks :
If the central unit starts functioning
erratically, either an indicator bulb is
not working or the main connecter (9way) is not properly connected.
If the central unit makes a crackling
sound, either there is a short circuit
between an orange or blue wire and
earth or the battery is discharged.
If the central unit does not work,
before changing it, check:
- Battery voltage (it must be over 10
volts).
the 4 bulbs of the indicators and the
telltale bulb.
- that the central unit is supplied with
12 volts (if not, check the fuse, the key
switch, the connections, the black
wire).

Trekker - Squab

20

D

1,2w

21
4x 10w

2
15
16
19
20
21
D

-

Ignition switch
Battery
5A Fuse
Turn signal relay
Indicator control
Indicator bulbs
Indicator telltale

ELECTRIC EQUIPMENT
STARTER MOTOR CIRCUITS
Operating principle :
The starter motor requires two circuits.

1. Control circuît :

27 0,75Ω 4w

14
5/21w
5A
3
1

2

12V 4Ah

5

off
4

15

16

on

This consists of the following elements
connected in series:
Battery, fuse, key switch, stop
switches, starter motor relay, start
switch (START).
With the ignition key in the ON
position, one or both stop switches
closed, the start switch closed, the
current supplied by the battery runs
through the coils of the relay and
closes by magnetic force, the power
circuit contact.

24

6

2. Power circuit :

23

This consists of the battery and starter
motor.
Activated by the relay, this circuit
consists of big wires aimed at
supporting high intensity. This circuit
is not protected by the 1OA fuse.

Troubleshooting :
Checks in the event of non starting.
Battery in good condition.
If the relay «clicks», check the battery
connections, the starter motor
connector, earthing of the starter
motor, the starter motor itself.
If the relay does not «click», look at
the taillight:
. if the taillight comes on, check the
relay
. if the taillight does not come on,
check: the battery, fuse, key switch,
stop lights, connectons.
Relay is good and working order
Relay at of order

25
26

Checking the starter motor :
Connect the starter motor directly to
the terminale of a 12 volt battery.

Checking the relay :
Connect a battery to the terminale of
the control circuit (small yellow / green
and purple wires). If the relay is
working correctly, it will «click» and will
make contact with the two other
terminals.

2
14
15
16
23
24
25
26
27

- Ignition switch
- Rear and stop light
- Battery
- 5A Fuse
- Stop contact switch
- Starter motor relay
- Starter motor control
- Starter motor
- Current limiter

Trekker - Squab

19

20

c

Trekker - Squab

6 5kΩ

5 5kΩ

1

d

10

8

4

a

b

b

a

3

7

17

18

4

1
on
6

C

28

5

2

1,2w

off

3

9

21

1,2w

D

4x 10w

11

5,9Ω 30w

6,7Ω 5w

20

19

E

16

5A

14

23

10Ω

100Ω

22

5/21w

25

24

B
1,2w

A
3 x 1,2w

26

12V 4Ah

15

27 0,75Ω 4w

15w

13

Squab 50 without dipped headlights

4

a

b

b

a

3

7

Trekker - Squab

17

18

4

1
on
6

5

2

28

1,2w

C

off

3

11

5,9Ω 30w

6,7Ω 5w

9

21

D

1,2w

20

19

13

12

L

35/35w

E

H

23

16

22

5A

10Ω

5/21w

24

25

27

5w

26

12V 4Ah

15

0,75Ω 4w

3 x 1,2w

1,2w

14

A

B

33

Trekker 50 all types and Squab 50 with main beam +
dipped headlights

21

KEY TO ELECTRIC CIRCUITS

A
B
C
D
E

Instrument panel lighting
Headlamp telltale
Low oil level telltale
Indicator telltale
Fuel gauge receiver

1

Flywheel
a ignition
b sensor
c alternative current
d battery charge current

2
3
4
5
6
7

Ignition switch
CDI ignition unit
High voltage coil
Interference suppresser 5 KW
Spark plug 5 KW
Regulator, rectifier
a regulator (AC)
b regulator, rectifier (DC)

8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
33

Choke
Resistance 6,7 W - 5 W
Lighting control
Resistance 5,9 W - 30 W
Headlamp control
Headlamp bulb
Rear and stop light bulb
Battery
Fuse
Horn
Horn button
Turn signal relay
Indicator control
Indicator bulbs
Fuel gauge
Stop light contact switches
Starter motor relay
Starter motor control
Starter motor
Current limiter
Low oil level contact switch
Number* plate lighting

22

* According to the model

22

Trekker - Squab

Note

2

Trekker - Squab

23

INTRODUCTION
This workshop manual concerns the FB engine which is fitted on several 50cm3
vehicles on the air-cooled version:
- FB0 ............................................ ZENITH
- FB1 ............................................ BUXY - SPEEDAKE
- FB2 ............................................ SQUAB - TREKKER
- FB4 ............................................ SPEEDFIGHT - TREKKER ROAD

The electric part of this manual only concerns the TREKKER and SQUAB vehicle
ranges.

PEUGEOT MOTOCYCLES RECOMMENDS
2 STROKE OIL

- ESSO 2T SPECIAL ................. 1 LITRE........ Ref. : 753752
- ESSO 2T SYNTHETIC ............ 1 LITRE........ Ref. : 753759
TRANSMISSION CASE OIL

- GEAR OIL GX-SAE 8OW-90 ... 2 LITRES ..... Ref. : 753009
HIGH TEMPERATURE GREASE

- SKF LGHT 3/0.4 ............................................ Ref. : 752093

GREASE

- MULTI-PURPOSE .......................................... Grease 4746

TIME SAVINGS = MONEY SAVINGS
Trekker - Squab

N° 11.753784.00

Dans un souci constant d'amélioration Peugeot Motocycles se réserve le droit de modifier, supprimer ou ajouter toute référence citée
DC/PS/SH Imp. en U.E 10/07/98

recommends



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2002:02:19 11:38:33Z
Subject                         : 753784
Modify Date                     : 2002:02:19 16:39:43+01:00
Page Count                      : 26
Has XFA                         : No
Creation Date                   : 2002:02:19 11:38:33Z
Producer                        : Acrobat Distiller 3.0 for Windows
Keywords                        : 
Author                          : Administrateur
Mod Date                        : 2002:02:19 16:39:43+01:00
Metadata Date                   : 2002:02:19 16:39:43+01:00
Description                     : 753784
Creator                         : Administrateur
Title                           : 753784
EXIF Metadata provided by EXIF.tools

Navigation menu