Philips Consumer Lifestyle HTL5110 SOUNDBAR SPEAKER User Manual

Philips Consumer Lifestyle SOUNDBAR SPEAKER Users Manual

Users Manual

www.philips.com/welcomeUser manualAlways there to help youRegister your product and get support atQuestion?Contact Philips
1ENContents1 Important 2Help and support 2Important safety instructions 2Care for your product 4Care of the environment 42 Your SoundBar 5Main unit 5Remote control 5Connectors 73 Connect and set up 8Subwoofer 8Connect audio from TV and other devices 94 Use your SoundBar 10Adjust the volume 10Choose your sound 10MP3 player 11USB storage devices 11Play audio through Bluetooth 11Auto standby 12Apply factory settings 125 Wall mount 136 Productspecications 147 Troubleshooting 158 Notice 16Notice of compliance 16Trademarks 16
2 3ENEN• Install all batteries correctly, + and - as marked on the unit.• Do not mix batteries (old and new or carbon and alkaline, etc.).• Remove batteries when the unit is not used for a long time.• The batteries shall not be exposed to excessiveheatsuchassunshine,reorthe like.• Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate.• The product/remote control may contain a coin/button type battery, which can be swallowed. Keep the battery out of reach of children at all times! If swallowed, the battery can cause serious injury or death. Severe internal burns can occur within two hours of ingestion.• If you suspect that a battery has been swallowed or placed inside any part of the body, seek immediate medical attention.• When you change the batteries, always keep all new and used batteries out of reach of children. Ensure that the battery compartment is completely secure after you replace the battery.• If the battery compartment cannot be completely secured, discontinue use of the product. Keep out of reach of children and contact the manufacturer. •Apparatus shall not be exposed to dripping or splashing. •Do not place any sources of danger on the apparatus (forexample.liquidlledobjects, lighted candles). •This apparatus may contain lead and mercury. Dispose according to local, State or Federal laws. For disposal or recycling information, please contact your local authorities. For additional assistance on recycling options, please contact www.mygreenelectronics.com or www.eiae.org or www.recycle.philips.com. •Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. •Do not place this apparatus on the furniture that is capable of being tilted by a child and an adult leaning, pulling, standing or climbing on it. A falling apparatus can cause serious injury or even death.• This apparatus should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided. Make sure to leave a space of 7.8 inches (20cm) or more around this apparatus.Class II equipment symbol This symbol indicates that the unit has a double insulation system. This 'bolt of lightning' indicates uninsulated material within your unit may cause an electrical shock. For the safety of everyone in your household, please do not remove product covering. The 'exclamation point' calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems. WARNING:Toreducetheriskofreorelectric shock, this apparatus should not be exposedtorainormoistureandobjectslledwith liquids, such as vases, should not be placed on this apparatus. CAUTION: To prevent electric shock, match wide blade of plug to wide slot, fully insert. 1 ImportantRead and understand all instructions before you use your product. If damage is caused by failure to follow instructions, the warranty does not apply.Help and supportPhilips provides extensive online support. Visit our website at www.philips.com/support to:• download the user manual and the quick start guide• watch video tutorials (available only for selected models)• ndanswerstofrequentlyansweredquestions (FAQs)• email us a question• chat with our support representative.Follow the instructions on the website to select your language, and then enter your product model number. Alternatively, you can contact Philips Consumer Care in your country. Before you contact Philips, note down the model number and serialnumberofyourproduct.Youcanndthisinformation on the back or bottom of your product.Important safety instructions •Read these instructions. •Keep these instructions. •Heed all warnings. •Follow all instructions. •Do not use this apparatus near water. •Clean only with dry cloth. •Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. •Do not install near any heat sources such as radiators, heat registers, stoves, or otherapparatus(includingampliers)thatproduce heat. •Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plugdoesnottintoyouroutlet,consultan electrician for replacement of the obsolete outlet. •Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. •Only use attachments/accessories speciedbythemanufacturer. •Use only with the cart, stand, tripod, bracketortablespeciedbythemanufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. •Unplug this apparatus during lightning storm or when unused for long periods of time. •Refer all servicing toqualiedservicepersonnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. •Battery usage CAUTION - To prevent battery leakage which may result in bodily injury, property damage, or damage to the unit:
4 5ENEN2 Your SoundBarCongratulations on your purchase, and welcometoPhilips!Tofullybenetfromthe support that Philips offers, register your SoundBar at www.philips.com/welcome.Main unitThis section includes an overview of the main unit. a (Standby-On/Standby indicator)• Switch the SoundBar on or to standby.• When the SoundBar is in standby, the standby indicator turns red.b VOLUME +-Increase or decrease volume.c SOURCESelect an input source or Bluetooth mode for the SoundBar.d Source indicators• AUDIO IN: Lights up when you switch to AUDIO-IN source (3.5mm jack).• BLUETOOTH: Lights up when you switch to Bluetooth mode and Bluetooth devices are paired. Blinks when you switch to Bluetooth mode and Bluetooth devices are not paired.• OPT/COAX: Lights up when you switch to coaxial or optical input source. Blinks when an unsupported audio format is detected.abcd e• AUX: Lights up when you switch to AUX input source.• USB: Lights up when you switch to USB mode.e SURR• Lights up when surround mode is selected. • Off when stereo mode is selected.• Blinks once when night mode/auto volume is enabled.• Blinks twice when night mode/auto volume is disabled.• Blinks twice when Dolby Digital audio is input.Remote controlThis section includes an overview of the remote control.Care for your productUseonlymicroberclothtocleantheproduct.Care of the environment Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. Please visit www.recycle.philips.com for additional information on a recycling center in your area. Never dispose of your product with other household waste. Please inform yourself about the local rules on the separate collection of electrical and electronic products and batteries. The correct disposal of these products helps prevent potentially negative consequences on the environment and human health.The batteries supplied do not contain the heavy metals mercury and cadmium. Nevertheless, in many areas batteries may not be disposed of with your household waste. Please ensure you dispose of batteries according to local regulations.For perchlorate material, special handling may apply. Visit www.dtsc.ca.gov/hazardouswaste/perchlorate.
6 7ENENswitch audio output from the Soundbar speaker or TV speaker. p (Play/Pause)Start, pause or resume play in USB mode and Bluetooth mode (only for AVRCP-supported Bluetooth devices).Press and hold to stop play in USB mode.q USBSwitch to USB mode.ConnectorsThis section includes an overview of the connectors available on your SoundBar.Side connectors a AUDIO INAudio input from an MP3 player (3.5mm jack).b (USB)Audio input from a USB storage device.Rear connectors a AUDIO IN-AUXConnect to an analog audio output on the TV or an analog device. b DIGITAL IN-OPTICALConnect to an optical audio output on the TV or a digital device. c DIGITAL IN-COAXIALConnect to a coaxial audio output on the TV or a digital device. d AC MAINS~Connect to the power supply.d a (Standby-On) • Switch the SoundBar on or to standby.• When EasyLink is enabled, press and hold for at least three seconds to switch all connected HDMI CEC compliant devices to standby.b HDMI selectionHDMI ARC/HDMI 1/HDMI 2: The function of those buttons is not available on this model.c Source buttons6781345ijklmnopq2OPTICAL: Switch your audio source to the optical connection. AUDIO IN: Switch your audio source to the AUDIO-IN connection (3.5mm jack).AUX: Switch your audio source to the AUX connection. COAX: Switch your audio source to the AUX connection. Bluetooth: Switch to Bluetooth mode.d (Repeat)Selectorturnoffrepeat/shufemodeinUSB mode.e / (Previous/Next)Skip to the previous or next track in USB mode and Bluetooth mode (only for AVRCP-supported Bluetooth devices).f SOUNDThe function of this button is not available on this model.g DIMSet the brightness of SoundBar display panel.h AUTO VOLTurn auto volume on or off.i NIGHT MODETurn night mode on or off.j BASS +/-Increase or decrease bass.k TREBLE +/-Increase or decrease treble.l AUDIO SYNC +/-The function of this button is not available on this model.m +/- (Volume)Increase or decrease volume.n (Mute)Mute or restore volume.o SURRSelect surround or stereo sound.In HDMI in mode (connected via HDMI IN 1 or HDMI IN 2), press and hold to
8 9ENENConnectConnect your subwoofer to your SoundBar as described in the quick start guide.Connect audio from TV and other devicesPlay audio from TV or other devices through your Soundbar speakers.Use the best quality connection available on your TV, Soundbar, and other devices. Note •When your Soundbar and TV are connected through HDMI ARC, an audio connection is not required.Option 1: Connect audio through a digital optical cableBest quality audio 1 Using an optical cable, connect the OPTICAL connector on your SoundBar to the OPTICAL OUT connector on the TV or other device. • The digital optical connector might be labeled SPDIF or SPDIF OUT. Option 2: Connect audio through a digital coaxial cableGood quality audio TV 1 Using a coaxial cable, connect the COAXIAL connector on your SoundBar to the COAXIAL/DIGITAL OUT connector on the TV or other device. • The digital coaxial connector might be labeled DIGITAL AUDIO OUT. Option 3: Connect audio through analog audio cablesBasic quality audio1 Using an analog cable, connect the AUX connectors on your SoundBar to the AUDIO OUT connectors on the TV or other device. DVD3 Connect and set upThis section helps you connect your SoundBar to a TV and other devices, and then set it up. For information about the basic connections of your SoundBar and accessories, see the quick start guide. Note •Foridenticationandsupplyratings,seethetypeplateat the back or bottom of the product. •Before you make or change any connections, make sure that all devices are disconnected from the power outlet.SubwooferFollow the steps below to position and connect your subwoofer. PositionPlace the subwoofer at least one meter (three feet) away from either to the left or right of your SoundBar, and ten centimeter away from the wall.For best results, place your subwoofer as shown below. Pair up with the subwooferThe wireless subwoofer automatically pairs up with the SoundBar for wireless connection when you turn on the SoundBar and the subwoofer. If no audio from the subwoofer can be heard, manually pair up the subwoofer.Pair up with the subwoofer1 Turn on the SoundBar and the subwoofer. » If the connection to the SoundBar is lost, the indicator on the subwoofer blinks white slowly.2 Press the CONNECT button on the subwoofer to enter the pairing mode. » The indicator on the subwoofer blinks white quickly.3 On the remote control, press AUX, and then press TREBLE -, BASS + and + (Volume) within three seconds. » If the pairing succeeds, the indicator on the subwoofer lights up white. » If the pairing fails, the indicator on the subwoofer blinks white slowly.4 If the pairing fails, repeat the steps above.
10 11ENENMP3 playerConnect your MP3 player to play your audio lesormusic.What you need• An MP3 player.• A 3.5mm stereo audio cable.1 Using the 3.5mm stereo audio cable, connect the MP3 player to the AUDIO IN connector on your SoundBar.2 PressAUDIO IN on the remote control.3 Press the buttons on the MP3 player to selectandplayaudiolesormusic.USB storage devicesEnjoy audio on a USB storage device, such as an MP3playerandUSBashmemory,etc.What you need• A USB storage device that is formatted forFATlesystems,andcomplieswiththeMass Storage Class.• AnMP3orWMAleonaUSBstoragedevice1 Connect a USB storage device to the SoundBar.2 Press USB on the remote control. 3 Use the remote control to control play.Button ActionStart, pause or resume play.Press and hold to stop play. / Skip to the previous or next track.SHUFFLE Selectorturnoffrepeat/shufemode.Note •This product may not be compatible with certain types of USB storage device. •If you use a USB extension cable, USB HUB, or USB multi-reader, the USB storage device may not be recognized. •Digital camera PTP protocols are not supported. •Do not remove the USB storage device while it is being read. •DRM-protectedmusicles(MP3,WMA)arenotsupported. •Support a USB port: 5V , 1A.Play audio through BluetoothThrough Bluetooth, connect the SoundBar with your Bluetooth device (such as an iPad, iPhone, iPod touch, Android phone, or laptop), and then youcanlistentotheaudiolesstoredonthedevice through your SoundBar speakers.What you need• A Bluetooth device which supports BluetoothproleA2DP,AVRCPandwithBluetooth version as 3.0 + EDR.• The operational range between the SoundBar and a Bluetooth device is approximately 10 meters (30 feet).1 Press Bluetooth on the remote control to switch the SoundBar to Bluetooth mode. » The BLUETOOTH indicator blinks.2 On the Bluetooth device, switch on Bluetooth, search for and select Philips HTL5110 to start connection (see the user manual of the Bluetooth device on how to enable Bluetooth). » During connection, the BLUETOOTH indicator blinks.3 Wait until you hear a beep sound from the SoundBar. » The BLUETOOTH indicator lights up. » If the connection fails, the BLUETOOTH indicator blinks continually.4 Use your SoundBarThis section helps you use the SoundBar to play audio from connected devices.Before you start• Make the necessary connections described in the quick start guide and the user manual.• Switch the SoundBar to the correct source for other devices.Adjust the volumeTo increase or decrease volume, press +/- (Volume).• The Source indicators on the front panel blink once when the volume is set to either minimum or maximum.To mute sound, press (Mute).• The current Source indicator on the front panel blinks continuously.To restore the sound, press (Mute) again or press +/- (Volume).Choose your soundThis section helps you choose the ideal sound for your video or music.Surround sound modeExperience an immersive audio experience with surround sound modes.Press SURR repeatedly to switch surround mode on or off. » When surround mode is on, the SURR indicator on the front panel lights up. » When stereo mode is on, the SURR indicator on the front panel turns off.EqualizerChange the high frequency (treble) and low frequency (bass) settings of the SoundBar.1 Press TREBLE +/- or BASS +/- to change the frequency. » SURR indicator blinks once every time you press TREBLE +/- or BASS +/-. » SURR indicator lights up for two seconds when treble or bass is set to the maximum or minimum value.Auto volumeTurn the auto volume on to keep the volume constant when you switch to a different source. 1 Press AUTO VOL to turn auto volume on or off. » When auto volume is turned on, the SURR indicator blinks once. » When auto volume is turned off, the SURR indicator blinks twice.Night modeFor quiet listening, decrease the volume of loud sounds when audio is played. Night mode is only available for Dolby Digital soundtracks. 1 Press NIGHT MODE to turn night mode on or off. » When night mode is turned on, the SURR indicator blinks once. » When night mode is turned off, the SURR indicator blinks twice.Note •If auto volume is set to turned on, you cannot enable the night mode.
12 13ENEN5 Wall mountNote •Koninklijke Philips Electronics N.V. bears no responsibility for improper wall mounting that results in accident, injury or damage. If you have any query, contact Philips Consumer Care in your country. •Before wall mounting, make sure the wall can support the weight of your SoundBar. •Before wall mount, you need not remove the three rubber feet at the bottom of the soundbar, otherwise therubberfeetcannotbexedback.Screw length/diameterDepending on the type of wall mounting your SoundBar, make sure that you use screws of a suitable length and diameter. For information about how to wall mount your SoundBar, see the quick start guide.> 25mm3.5-4mm4mm4 Selectandplayaudiolesormusiconyour Bluetooth device.• During play, if a call is coming, music play is paused. Play resumes when the call ends.• If your Bluetooth device supports AVRCPprole,ontheremotecontrolyou can press / to skip to a track, or press to pause/resume play.5 To exit Bluetooth, select other source.• When your switch back to Bluetooth mode, Bluetooth connection remains active.Note •The music streaming may be interrupted by obstacles between the device and SoundBar, such as wall, metallic casing that covers the device, or other devices nearby that operate in the same frequency. •If you want to connect your SoundBar with another Bluetooth device, press and hold Bluetooth on the remote control to disconnect the currently connected Bluetooth device. •Philips does not guarantee 100% compatibility with all Bluetooth devices.Auto standbyWhen playing media from a connected device, the SoundBar automatically switches to standby if:• no button is pressed for 29 minutes, and• no audio/video play from a connected device.Apply factory settingsYou can reset your SoundBar to the default settings programmed at the factory.1 In AUX mode, within three seconds, press VOL-, BASS-,and Treble- . » When the factory settings restore is complete, the SoundBar automatically switches off and restarts.
14 15ENEN7 TroubleshootingWarning •Risk of electric shock. Never remove the casing of the product.To keep the warranty valid, never try to repair the product yourself. If you have problems using this product, check the following points before you request service. If you still have a problem, get support at www.philips.com/support. Main unitThe buttons on the SoundBar do not work.• Disconnect the SoundBar from the power supply for a few minutes, then reconnect.SoundNo sound from SoundBar speakers.• Connect the audio cable from your SoundBar to your TV or other devices. However, you do not need a separate audio connection when:• the SoundBar and TV are connected through HDMI ARC connection, or• a device is connected to the HDMI IN connector on your SoundBar.• Reset your SoundBar to its factory settings.• On the remote control, select the correct audio input.• Make sure that the SoundBar is not muted. Distorted sound or echo.• If you play audio from the TV through the SoundBar, make sure that the TV is muted.No sound from the wireless subwoofer.• Wirelessly connect the subwoofer to the main unit.BluetoothA device cannot connect with the SoundBar.• The device does not support the compatibleprolesrequiredfortheSoundBar.• You have not enabled the Bluetooth function of the device. See the user manual of the device on how to enable the function.• The device is not correctly connected. Connect the device correctly.• The SoundBar is already connected with another Bluetooth device. Disconnect the connected device, then try again.Quality of audio play from a connected Bluetooth device is poor.• The Bluetooth reception is poor. Move the device closer to the SoundBar, or remove any obstacle between the device and the SoundBar.The connected Bluetooth device connects and disconnects constantly.• The Bluetooth reception is poor. Move the device closer to the SoundBar, or remove any obstacle between the device and the SoundBar.• Turn off Wi-Fi function on the Bluetooth device to avoid interference.• For some Bluetooth, the Bluetooth connection can be deactivated automatically to save power. This does not indicate any malfunction of the SoundBar.6 Product specificationsNote •Specicationsanddesignaresubjecttochangewithoutnotice.Amplier• FTC total output power: 34W• Left + Right: 16W (1%THD, 4ohm, 300Hz-20kHz)• Subwoofer: 18W (1%THD, 8ohm, 40Hz-70Hz)• RMS total output power: 120W RMS (+/- 0.5 dB, 30% THD) / 96W RMS (+/- 0.5 dB, 10% THD)• Frequency response: 20 Hz-20 kHz / ±3 dB• Signal-to-noise ratio: > 65 dB (CCIR) / (A-weighted)• Input sensitivity:• AUX: 750 mV• AUDIO IN: 400 mVAudio• S/PDIF Digital audio input:• Coaxial: IEC 60958-3• Optical: TOSLINKUSB• Compatibility: Hi-Speed USB (2.0)• Class support: USB Mass Storage Class (MSC)• File system: FAT16, FAT32• SupportsMP3andWMAleformats• Sampling frequency:• MP3: 8 kHz, 11 kHz, 12 kHz, 16 kHz, 22 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz• WMA: 44.1 kHz, 48 kHz • Constant bit rate:• MP3: 8 kbps-320 kbps• WMA: 32 kbps-192 kbps• Version:• WMA: V7, V8, V9Bluetooth •Bluetoothproles:A2DP,AVRCP •Bluetooth version: 3.0 + EDRMain unit •Power supply: 110-240 V~, 50/60 Hz •Power consumption: 25 W •Standbypowerconsumption:≤0.5W• Speaker impedance: 8 ohm• Speaker drivers: 4 x 3" woofer •Dimensions (WxHxD): 995 x 94 x 102.5 mm •Weight: 3.5 kgSubwoofer• Power supply: 110-240 V~, 50/60 Hz• Power consumption: 30 W• Standbypowerconsumption:≤0.5W• Impedance: 4 ohm• Speaker drivers: 1 x 165 mm (6.5") woofer• Dimensions (WxHxD): 200 x 510 x 201 mm• Weight: 4.9 kgRemote control batteries• 2 x AAA-R03-1.5 V
16 EN8 NoticeThis section contains the legal and trademark notices.Notice of complianceThis set complies with the FCC rules, Part 15 and with 21 CFR 1040.10. Operation is subject to the following two conditions:a This device may not cause harmful interference, andb This device must accept any interference received, including interference that may cause undesired operation.FCC rulesThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Relocate the receiving antenna.• Increase the separation between equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.FCC Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.Warning:Changesormodicationsmadetothis equipment not expressly approved by Philips may void the FCC authorization to operate this equipment.Model number: PHILIPS HTL5110/F7Trade Name: PhilipsResponsible Party:P&F USA, Inc. PO Box 2248 Alpharetta, GA 30023-2248; 1-866-310-0744Canada: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following Two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This Class B digital apparatus complies with Canadian ICES-003. Trademarks Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Philips is under license.
Specifications are subject to change without notice© 2013 Koninklijke Philips Electronics N.V.All rights reserved.Document order number: 000000000000

Navigation menu