Philips Consumer Lifestyle M1BT Bluetooth headphone User Manual M1BT UM EN 20130628 2

Philips Consumer Lifestyle Bluetooth headphone M1BT UM EN 20130628 2

User Manual

Always there to help you Register your product and get support at www.philips.com/welcome Question? Contact Philips M1BT User manual
Contents 1 Important safety instructions 2 Hearing Safety 2 General information 2 2 Your wireless on-ear headset 3 What's in the box 3 Other devices Over view of your wireless on-ear headset 3 4 3 Get started 5 Charge your headset 5 Pair the headset with your mobile phone 5 4 Use your headset Connect the headset to a Bluetooth device Manage your calls and music 6 6 6 Wear your headset Use with the audio cable 7 7 5 Technical data 8 6 Notice 9 Declaration of conformity Disposal of your old product and batteries 9 9 Notice for the European Union Trademarks 10 10 7 Frequently asked questions 12 EN 1
1 Important safety instructions Hearing Safety Danger • To avoid hearing damage, limit the time you use the headset at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is. Be sure to observe the following guidelines when using your headset. • Listen at reasonable volumes for reasonable periods of time. • Be careful not to adjust the volume continuously upwards as your hearing adapts. • Do not turn up the volume so high that you can’t hear what’s around you. • You should use caution or temporarily discontinue use in potentially hazardous situations. • Excessive sound pressure from earphones and headset can cause hearing loss. • Using the headset with both ears covered while driving is not recommended and may be illegal in some areas while driving. • For your safety, avoid distractions from music or phone calls while in traffic or other potentially dangerous environments. General information To avoid damage or malfunction: Caution • Do not expose the headset to excessive heat. • Do not drop your headset. • Headset shall not be exposed to dripping or splashing. • Do not allow your headset to be submerged in water. • Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives. • If cleaning is required use a soft cloth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product. • The integrated battery shall not be exposed to excessive heat such as sunshine, fire or the like. About operating and storage temperatures and operating altitude • Operate or store in a place where temperature is between -15ºC (5ºF) and 55ºC (131ºF) (up to 90% relative humidity. • Batter y life may be shorter in high or low temperature conditions. This Philips appliance complies with all applicable standards and regulations regarding exposure to electromagnetic fields. 2 EN
2 Your wireless on-ear headset Congratulations on your purchase, and welcome to Philips! To fully benefit from the suppor t that Philips offers, register your product at www.philips.com/welcome. With this Philips wireless on-ear headset, you can: • enjoy convenient wireless handsfree calls; • enjoy and control wireless music; • switch between calls and music; • enjoy music on non-Bluetooth devices with an audio cable. What's in the box Philips Bluetooth wireless on-ear headset M1 BT USB charging cable Audio cable Quick star t guide Other devices A mobile phone or device (e.g. notebook, PDA, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible to the headset (see 'Technical data' on page 8). Note • You can find a list of compatible mobile phones/devices at www.philips.com/support. EN 3
Overview of your wireless on-ear headset f e d c b a a Audio cable jack b Charging slot c Microphone d Volume/Track control button e Call/Music button f LED lights 4 EN
3 Get started Charge your headset Note • Before you use your headset for the first time, charge the batter y for 4 hours for optimum batter y capacity and lifetime. • Use only the original USB charging cable to avoid any damage. • Finish your call before charging the headset, as connecting the headset for charging will power the headset off. • You can operate the headset normally during charging. Connect the supplied USB charging cable to: • the USB connector of the headset and; • USB power source. » LED turns white during charging and turns off when the headset are fully 1 Make sure that the mobile phone is turned on and its Bluetooth feature is activated. 2 Make sure that the headset is fully charged and turned off. 3 Press and hold the call/music button for 10 seconds until the white and blue LED flashes alternately. » The headset remains in pairing mode for 5 minutes. 4 Pair the headset with the mobile phone. For detailed information, refer to the user manual of your mobile phone. The following example shows you how to pair the headset with your mobile phone. 1 Activate the Bluetooth feature of your mobile phone, select Fidelio M1 BT. 2 Enter the headset password "0000" (4 zeros) if prompted. For those mobile phones featuring Bluetooth 2.1+EDR or higher, no need to enter a password. charged. Settings Bluetooth 10:35 Connectivity Settings Devices Found 10:36 10:37 Settings Connectivity Tip • Normally, a full charge takes 5 hours. • When your batter y is empty, you can carr y on listening music with an audio cable. Make sure the headset is off (and not in idle mode) before using this audio cable. Pair the headset with your mobile phone Before you use the headset with your mobile phone for the first time, pair it with a mobile phone. A successful pairing establishes a unique encrypted link between the headset and mobile phone. The headset stores the last 8 devices in the memory. If you try to pair more than 8 devices, the earliest paired device is replaced by the new one. Add Bluetooth device Select Back Fidelio M1BT Select Back Enter Password **** 0000 Select Back EN 5
4 Use your headset Connect the headset to a Manage your calls and music Call/Music button Task Operation Sound or LED indicator Bluetooth device 1 Turn on your mobile phone/Bluetooth device. 2 Press and hold the call/music button to turn the headset on. » The blue LED flashes. » The headset is reconnected to the last connected mobile phone/ Bluetooth device automatically. If the last one is not available, the headset tries to reconnect to the second last Turn the headset on. Turn the headset off. Press and hold for 1 second. Press and hold for 4 seconds. • 1 shor t beep • 3 white flashes: batter y low < 25% • 2 white flashes: batter y level < 50% • 1 blue flash: batter y level > 50% • 1 long beep • 1 long white flash connected device. Note • If you connect the headset to an iphone, ipad or ipod Touch (iOS version 5.0 or above), the battery indicator Play or pause music. Pick up or terminate a call. Press once. 1 short beep Press once. 1 short beep is displayed on the iphone, ipad or ipod Touch. Tip Reject an incoming call. Press and hold 1 short beep • If you turn on the mobile phone/Bluetooth device or activate the Bluetooth feature after turning on the headset, you have to reconnect the headset and mobile phone/Bluetooth device manually. Redial the last number. Switch caller during a call. Press twice. 1 short beep Press twice 1 long beep Volume/Track control button Adjust volume. turn up/ down Skip forward. Press once Skip backward. Press twice 1 short beep 1 short beep 1 short beep Mute/unmute the microphone in a call. Press once 1 short beep/2 short beeps 6 EN
Other headset indicator status Headset status Indicator Use with the audio cable The headset is connected to a Bluetooth device, while the headset in standby mode or while you are listening to music. The headset is ready for pairing. The headset is on but not connected to a Bluetooth device. Blue LED flashes for ever y 8 seconds. LED flashes white and blue alternately. Blue LED flashes quickly. Note • Finish your call before connecting the audio cable, as this will switch off the battery power of the headset and end an incoming call. With the supplied audio cable, you can use the headset with non-Bluetooth devices or on airplane. No battery power is required for the headset when you use it with the audio cable. Connect the supplied audio cable to • the headset and; There is an incoming call. Blue LED flashes twice per second. Low batter y. White LED flashes. Batter y is fully charged. White LED is off. Wear your headset Adjust the headband to fit your head. Tip • After use, twist and fold the headset up for storage. • an external audio device. EN 7
5 Technical data • Minimum 10 hours of music time or talk time • Minimum 350 hours of standby time • Normal time for a full charge: 3 hours • Rechargeable Lithium-Polymer batter y (230 mAh) • 3.5 mm audio jack for corded headset mode • Bluetooth 2.1+EDR or 4.0, Bluetooth mono support (Headset Profile - HSP, Hands-Free Profile - HFP), Bluetooth stereo supported (Advanced Audio Distribution Profile - A2DP; Audio Video Remote Control Profile - AVRCP) • Operating range: Up to 10 meters (33 feet) • Adjustable, flat-folding headband • Digital echo & noise reduction • Supports AAC audio • Auto power off Note • Specifications are subject to change without notice. 8 EN
6 Notice Declaration of conformity Hereby Philips Consumer Lifestyle, declares that the M1 BT is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. You can find the Declaration of Conformity on www.p4c.philips. com. This product has been designed, tested and manufactured according the European R&TTE directive 1999/5/EC. Disposal of your old product and batteries Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002/96/ EC. Please inform yourself about the local separate collection system for electrical and electronic products. Please act according to your local rules and do not dispose of your old products with your normal household waste. Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health. Your product contains batteries covered by the European Directive 2006/66/EC, which cannot be disposed with normal household waste. Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environmental and human health. Remove the integrated battery Note • Make sure the headset is disconnected from the USB charging cable before removing the battery. If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing the headset. 1 2 3 4 Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment. EN 9
Notice for the European Union Hereby, Philips Consumer Lifestyle, declares that Philips Fidelio M1 BT is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Trademarks Trademarks are the proper ty of Koninklijke Philips Electronics N.V. or their respective owners. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Koninklijke Philips Electronics N.V. is under license. iPhone, iPad and iPod Touch are trademarks of Apple Inc., registered in the U.S. and other countries. Notice for USA (FCC) This device complies with Par t 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. IC Radiation Exposure Statement: This equipment complies with Canada radiation exposure limits set forth for uncontrolled environments. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 10 EN
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Déclaration d’IC sur l’exposition aux radiations: Cet équipement est conforme aux limites d’exposition aux radiations définies par le Canada pour des environnements non contrôlés. Cet émetteur ne doit pas être installé au même endroit ni utilisé avec une autre antenne ou un autre émetteur. EN 11
7 Frequently asked questions My Bluetooth headset does not switch on. • The batter y is low. Charge the headset. • The audio cable is connected to the headset. Disconnect the audio cable. I cannot pair my Bluetooth headset with a mobile phone. The Bluetooth is disabled. Enable the Bluetooth feature on your mobile phone and turn on the mobile phone before you turn on the headset. Pairing does not work. Make sure the headset is in pairing mode. • Follow the steps described in this user manual (see 'Pair the headset with your mobile phone' on page 5). • Make sure that the LED light flashes white and blue alternately before you release the call/music button. Do not stop holding the button if you see the blue LED only. The mobile phone cannot find the headset. • The headset may be connected to a previously paired device. Turn off the connected device or move it out of range. • Pairing may have been reset or the headset has been previously paired with another device. Pair the headset with the mobile phone again as described in the user manual (see 'Pair the headset with your mobile phone' on page 5). Voice dialing or redialing does not work on my mobile phone. Your mobile phone may not support this feature. The other side cannot hear me on the mobile phone. The microphone is muted. Press volume/track control button to enable the microphone. 12 EN My Bluetooth headset is connected to a Bluetooth stereo enabled mobile phone, but music only plays on the mobile phone speaker. Refer to the user manual of your mobile phone. Select to listen to music through the headset. The audio quality is poor and crackling noise can be heard. The Bluetooth device is out of range. Reduce the distance between your headset and Bluetooth device, or remove obstacles between them. The audio quality is poor when streaming from the mobile phone is very slow, or audio streaming does not work at all. Make sure your mobile phone not only supports (mono) HSP/HFP but also supports A2DP (see 'Technical data' on page 8). I hear but cannot control music on my Bluetooth device (e.g. play/pause/skip forward/ backward). Make sure the Bluetooth audio source suppor ts AVRCP (see 'Technical data' on page 8). I cannot see the iPhone battery indicator after connecting the iPhone to the headset. Make sure your iPhone iOS version is 5.0 or above. My headset does not work when the audio cable is connected. Microphone function will be deactivated if a 3.5mm audio cable is connected to the headset. In such case, your headset is only for music enjoyment. How can I restore all original headset settings? Press volume/track control button and call music button until the LED flashing white for 5 times sequentially. For further support, visit www.philips.com/ support.
Specifications are subject to change without notice © 2013 Koninklijke Philips Electronics N.V. All rights reserved. M1BT_UM_00_EN 0890

Navigation menu