Philips DFU D 43pp8445 93 Eng

43PP8445/93 43pp8445_93_dfu_eng Philips 43PP8445/93 user manual - English, Pdf file (203 Kb) - Owner's / User's manual

43PP8446/93 43pp8446_93_dfu_eng Philips 43PP8446/93 user manual - English, Pdf file (1.51 Mb) - Owner's / User's manual

43PP8447/93 43pp8447_93_dfu_eng Philips 43PP8447/93 user manual - English, Pdf file (1.51 Mb) - Owner's / User's manual

User Manual: Philips DFU-D

Open the PDF directly: View PDF .
Page Count: 42

3135 035 23251

Rear-projection TV

with HD Input

Rear-projection TV

with HD Input

43PP8445

43PP8446

43PP8447

CONTENTS

Setup and Installation

Product Highlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Installing the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Using the TV keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Using the Remote Control Keys . . . . . . . . . . . . . . . .6–7

Operation

Using the Menus

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8–13

Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14–16

Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18–21

Using Program List . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Using Smart Surf . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Using Smart Picture and Smart Sound . . . . . . . . . . . . .23

Using the Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . .24

Peripheral Equipment

Connecting Peripheral Equipment . . . . . . . . . . . . .25–33

Selecting Connected Equipment for Viewing . . . . . . . .34

General Information

Care, Cleaning, and Tips . . . . . . . . . . . . . . . . . . . . . . . .35

Before Calling Service . . . . . . . . . . . . . . . . . . . . . . . . .36

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

International Guarantee Conditions . . . . . . . . . . . .39-40

Consumer Information Centres . . . . . . . . . . . . . . .41–42

SAFETY INFORMATION

No naked flames, such as lighted candles, should be placed on top on the TV or in the vicinity.

Do not place your TV set under direct sunlight or heat.

Leave at least 15cm around each side of TV set to allow for proper ventilation.

Avoid placing you set (e.g. near the window) where it is likely to be exposed to rain or water.

No objects filled with liquids should be placed on top of the TV so as to avoid dripping or splashing of liquids on the set.

Disconnect mains plug when :

• the red light below the TV screen is flashing continuously

• a bright white line is displayed across the screen

• cleaning the TV screen (never use abrasive cleaning agents; use a slightly damp chamois leather or soft cloth)

• a lightning storm is occurring

• the set is left unattended for a prolonged period.

Never attempt to repair a defective TV yourself. Always consult a skilled service person.

Battery Usage CAUTION :

To prevent battery leakage which may result in bodily injury or damage to the remote :

• Install ALL batteries correctly, + and – as marked on the remote control.

• Do not mix batteries : (OLD and NEW or CARBON and ALKALINE, etc.).

• Remove batteries when the remote is not used for a long time.

Thank you for purchasing this television set. You are now the proud owner of a Philips TV, which promises full value to

you as a customer. Please read this manual carefully and thoroughly for help with installation and operation.

Note: Although every effort has been made to insure accuracy, your television may differ from the information presented

in this book.

PRODUCT HIGHLIGHTS

Electronics.

*Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

Please note: Not all features may be available on all models.

See it as an eyewitness

• Progressive Scan – double the visible picture lines for better resolution

• 100Hz Digital Scan eliminates flicker and line jitter for stable picture

• HDTV Monitor – HDTV is the latest and best television signal available

• Saphlon™ Screen – better picture and scratch resistance

Technology made simple

• Active Control measures signal to produce best picture

• APAC – Automatic Phosphor Aging Compensation

Rich sound experience

• Virtual Dolby®* Surround – surround sound without additional rear speakers

Product highlights

100Hz Digital Scan

Conventional TV creates a picture by scanning 50 times per second (50Hz). This frequency can be detected by the human eye in the form of a field flickering

picture. 100Hz sets scan 100 times per second, eliminating the field flickering.

Progressive Scan

A picture frame consists of two fields: the field with

the odd lines (field A) and the field with the even lines (field B). Instead of sending field A to the screen first, followed by field B, the fields A and B are written

at one time. In one second, a full image is created using the maximum resolution. At this speed, the human eye perceives a sharper picture with no line

structure.

HDTV Monitor

HDTV Display Capability (1080i). HDTV monitors enable you to view high-definition or enhanced-definition TV programming in the 1080i or 480p signal for-

mat. In order to do so, the TV must be connected via its component video or RGB inputs to a set-top box, which is set to operate in the DTV mode. A DTV

signal must be present in your area and the set-top box must be tuned to the proper channel. An external over-the-air antenna may be required. Another

option is HDTV broadcast satellite service. Stunning realism in both picture and sound are delivered!

Saphlon™ Screen

Saphlon™ Screen technology is built with

materials and processes that deliver more brightness and picture contrast. It guards against most scratches and fingerprints and eliminates the glare associat-

ed with a separate protective screen.

Active Control

With over 3,000 picture adjustments per minute,

this 'proactive control system' continuously analyzes incoming video signal qualities for Dynamic Noise Reduction and sharpness and then automatically cor-

rects them to be like the settings you previously selected in the picture menu.

APAC

APAC is designed to minimize the effects of image retention from stationary images on the screen. Because both analog sources (cable TV and DVD) and dig-

ital sources (HD and progressive scan DVD) have different aspect ratios (4:3, 16:9, 21:9, etc.), the picture on a digital television may have black bars on the

sides or top and bottom. When black bars are detected in either the 4:3 or 16:9 viewing mode, APAC automatically shifts the television picture pixel-by-pixel,

just enough to soften image retention. APAC works in both the analog and digital modes, so it provides excellent protection.

INSTALLING THE TV

SOURCE

15 cm

Do not place

the TV in

direct

sunlight or

near a heat-

ing appliance.

Mains Power

Switch

Power

1The major benefit of this projection tel-

evision is its large viewing screen. To

see the large screen at its best, test vari-

ous locations in the room to find the

optimal spot for viewing.

Be sure to allow a minimum of 15 cm

of space around the TV.

To avoid cabinet warping, cabinet color

changes, and increased chance of set

failure, do not place the TV where tem-

peratures can become excessively

hot—for example, in direct sunlight or

near a heating appliance.

Magnetic fields, such as those of exter-

nal speakers, may cause the picture to

distort if the speakers are placed too

close to the television. Move the mag-

netic field source away from the TV

until there is no picture distortion.

2Insert the aerial plug firmly into the

ANTENNA IN 75Ωsocket at the rear

of the set.

3Insert the mains plug in the wall sock-

et. Refer to the back of the TV set for

the correct operation voltage. Consult

your local dealer if your main supply is

different. To prevent damaging the

mains (AC) cord, which could cause

hazard, do not place the TV on the

cord.

4Remove the cover of the battery com-

partment on the remote control. Insert

the two batteries supplied

(Type R6-1.5V).

The batteries supplied do not contain

the heavy metals mercury and cadmi-

um. Nevertheless, in many countries

exhausted batteries may not be dis-

posed of with your household waste.

Please check on how to dispose of

exhausted batteries according to local

regulations.

See the battery caution statement on

page 2.

Note : This remote control functions

with TVs that use the RC5 signalling

standard.

5Switch the TV on : Press the mains

power switch on the front of the TV. If

the Standby key is lighted, press the

CH +/– keys, digit keys, or the Power

key on the remote control. Or press the

Standby or CH keys on the front of the

TV.

15 cm

ANTENNA IN 75Ω

Socket on the rear of

the TV

USING THE TV KEYS

MAINS POWER KEY

Switches the mains power on or off.

VOL %%ﬁﬁ/ MENU

The -

ﬁﬁkey adjusts the sound volume

softer. The%%key adjusts the sound

volume louder. Pressing -

ﬁﬁand %%

simultaneously displays the onscreen

TV menu. With a menu item selected,

pressing theﬁﬁor %%key allows entry

to the item. Pressing -

ﬁﬁand %%simul-

taneously and repeatedly exits the

onscreen menu.

CH %%ﬁﬁ

The ﬁﬁkey selects channels in

descending order. The %%key selects

channels in ascending order. When

the onscreen menu is displayed,

pressing ﬁﬁor %%selects the next item

in the menu. Also, use either of these

keys to switch the TV on from stand-

by mode.

POWER

Switches the TV on or

activates standby mode.

SOURCE

Press to selcet the input source for the

Press to activate th on-screen menu.

Navigate the menu by using the

Volume and Channel buttons.

SLEEP TIMER

Allows you to select a time period after which the set will automatical-

ly switch to standby mode. Choose 15, 30, 45, 60, 90, 120, 180, or 240

minutes. See page 24.

A/CH (Alternate Channel)

Allows you to alternate between the last viewed channel and the pres-

ent channel.

PICTURE-IN-PICTURE (PIP)

Not applicable.

FORMAT

Each press selects another picture format. For AV1, CVI, AV2, or

AV3, the options are 4:3, Auto, and Expand 4:3. For AV4 1080i sig-

nal sources, the options are 4:3 and Compress 16:9. For AV4 480p

or 576p signal sources, no screen format options are available

through the TV. Control the format at the source (DVD player or

digital set-top box).

DIGIT (0–9)

Allows you to select a channel. Note : For a two-digit number, the sec-

ond digit must be entered before the “–” sign disappears.

SMART SOUND

Allows you to select from three predefined optimal settings—Voice,

Music, and Theatre—and a Personal setting based on your own selec-

tions through the onscreen Sound menu. Press the key repeatedly to

select a setting. See page 23.

Displays the main menu. Also allows you to go backwards in the

menu system.

CURSOR LEFT

Allows you to access the menus and adjust the settings.

CURSOR UP

Allows you to select the next or previous item in the menu and to

select a screen format. See page 21.

VOLUME +/–

Increases or decreases volume.

Allows you to select the different signal sources connected to the TV.

i+ (STATUS/EXIT)

• Displays the channel number, sound and colour transmission

modes, status of the sleep timer, channel name (if the channel has

been named), and the current time (if the time has been set).

• Allows you to navigate or make adjustments in multipoint-conver-

gence mode.

• Allows you to switch the menu off.

DOLBY V (with Dolby* Surround Signals)

Allows you to select various factory surround-sound listening modes :

Dolby Virtual (Virtual Dolby Surround)

Dolby Virtual uses two speakers to simulate the surround effect pro-

duced by a multichannel system.

Incredible Surround™

• In Stereo sound mode—when switched on, the Incredible Surround™ fea-

ture provides the feeling that the speakers are farther apart to enhance the

home-cinema effect.

• In Mono sound mode—when switched on, the Incredible Surround feature

enables you to hear a spatial sound effect.

*Manufactured under license from Dolby Laboratories. “Dolby”

and the double-D symbol are trademarks of Dolby Laboratories.

USING THE REMOTE CONTROL KEYS

STANDBY

• Switches the set off temporarily to standby mode. (The red light

indicator lights up when the set is in standby mode.)

• To switch the set on from standby mode, press the Standby,

Channel +/–, or Digit (0–9) keys.

FREEZE

Allows you to freeze the main picture.

SMART PICTURE

Allows you to select from four predefined optimal settings—Rich,

Natural, Soft, and Multimedia—and a Personal setting based on

choices you make through the onscreen Picture menu. See

page 23.

SURF

Allows you to select up to 10 channels and quickly view them. See

page 22.

CURSOR RIGHT

Allows you to access the menus and adjust the settings.

CURSOR DOWN

Allows you to select the next or previous item in the menu or to select

a screen format.

CHANNEL +/–

Allows you to select channels in ascending and descending order.

MUTE

Allows you to mute the sound. To restore the sound, press the key

again.

TIMER

Allows you to access the onscreen Timer menu, through which you

can set the TV’s clock and the Timer. The Timer can be set to switch

to another channel at a specified time while you are watching another

channel or when the set is in standby mode.

I–II

Allows you to switch from stereo to mono sound during stereo trans-

mission or to choose between language I or language II during dual

sound transmission.

TELETEXT

Not applicable.

PROGRAM LIST

Allows you to navigate through a list of installed programmes for a

quick overview of the channels and to activate the channel you have

selected. See page 22.

ACTIVE CONTROL™

Allows you to switch the Active Control™ feature on or off. When

Active Control™ is on, it measures and corrects all incoming signals

to provide the best picture-quality settings, controlling Sharpness and

Noise Reduction continuously and automatically. The onscreen Active

Control™ display items cannot be selected. See page 21.

USING THE REMOTE CONTROL KEYS

1Press the MENU key to display/cancel the main menu.

2Use the cursor in the up/down directions to select a menu

item.

Note : Sometimes not all the menu items are visible on the

screen; press the cursor up/down until you can see the item

you desire.

3Use the cursor in the left/right directions to display the

menu and adjust the settings.

4Press the MENU key to return.

5Press the mkey to switch the menu off.

Note : If no action is executed, the menu automatically dis-

appears after about 20 seconds.

USING THE MENUS :OVERVIEW

Selecting the Menu Language

1Press the MENU key.

2Select INSTALL with the cursor down.

3Press the cursor right to select LANGUAGE.

4Press the cursor right again.

5Select your language with the cursor up/down.

From this point on, all onscreen displays will appear in the

language that you have chosen.

Now you can search for and store the TV channels in two

different ways : with Auto Store or Manual Store (tuning in

channel by channel).

USING THE MENUS :I

NSTALL

•PICTURE BRIGHTNESS

•SOUND COLOUR

•FEATURES CONTRAST

•INSTALL SHARPNESS

COLOUR TEMP

•PICTURE LANGUAGE

•SOUND AUTO STORE

•FEATURES MANUAL STORE

•INSTALL SORT

CHANNEL EDIT

INSTALL

LANGUAGE •ENGLISH

•AUTO STORE

•MANUAL STORE

•SORT

•CHANNEL EDIT

•

INSTALL

LANGUAGE •ENGLISH

•AUTO STORE

•MANUAL STORE

•SORT

•CHANNEL EDIT

•

Select

item

Return

Switch

off

Tuning Channels Automatically

1Select AUTO STORE in the INSTALL menu.

Press the cursor right to start the searching. All the TV channels

are searched for and stored automatically.

3When the tuning is completed, press the MENU key to

return to the INSTALL menu or press the mkey to switch

the menu off.

Note : Channel numbers will always be written in Latin

characters, even when a language that uses other characters

has been selected.

USING THE MENUS :INSTALL

Tuning Channels Manually

Manual tuning allows you to store channel by channel. You must go

through every step of the manual store menu.

1Select MANUAL STORE in the INSTALL menu.

2Press the cursor right to enter the menu.

3Select COLOUR SYSTEM and press the cursor right.

If AUTO is selected, the respective colour system will be

automatically selected according to the transmission system.

Note : If reception is poor, select another colour system

with the cursor up/down.

4Press the MENU key or the cursor left.

5Select SOUND SYSTEM and press the cursor right.

If AUTO is selected, the respective sound system will be

automatically selected according to the transmission system.

Note : If the reception is poor, select another sound system

with the cursor up/down.

6Press the MENU key or the cursor left.

7Select SEARCH and press the cursor left or right to start

the searching. Searching stops once a transmitting channel is

found

Note : If the reception is poor, select another colour and/or

sound system.

Continue to the next page.

INSTALL

•LANGUAGE

•AUTO STORE •SEARCH

•MANUAL STORE

•SORT

•CHANNEL EDIT

•

INSTALL

LANGUAGE

•AUTO STORE •SEARCHING

•MANUAL STORE PLEASE WAIT

•SORT CHAN.FOUND 8

•CHANNEL EDIT 048 31 MHZ

•

•PICTURE BRIGHTNESS

•SOUND COLOUR

•FEATURES CONTRAST

•INSTALL SHARPNESS

COLOUR TEMP

•PICTURE LANGUAGE

•SOUND AUTO STORE

•FEATURES MANUAL STORE

•INSTALL SORT

CHANNEL EDIT

INSTALL

•LANGUAGE COLOUR SYSTEM

•AUTO STORE SOUND SYSTEM

•MANUAL STORE SEARCH

•SORT CHANNEL

•CHANNEL EDIT FINE TUNE

•

INSTALL

MANUAL STORE

•COLOUR SYSTEM

•SOUND SYSTEM

SEARCH •196.25MHZ

•CHANNEL

•STORE

•

INSTALL

MANUAL STORE

•COLOUR SYSTEM

•SOUND SYSTEM

SEARCH •048.31MHZ

•CHANNEL

•STORE

•

8Select CHANNEL.

9Key in the desired channel number with the digit keys or

with the cursor left/right.

10Press the cursor down.

In case of poor reception, you can improve the reception by

adjusting the frequency using FINE TUNE.

11Select FINE TUNE and press the cursor left/right to adjust.

12In rare cases, certain TV channels may reproduce distorted

or unstable pictures.

Select PLL (Phase Locked Loop) to switch to the setting 2

with the cursor left/right to restore the picture for the respec-

tive transmission.

13Select STORE.

14Press the cursor right.

The message STORED appears and the search menu item is

highlighted again.

15Now repeat steps 7–14 to continue searching for another

transmitting channel.

16Press the MENU key to return to the INSTALL menu or

press the mkey to switch the menu off.

USING THE MENUS :INSTALL

INSTALL

MANUAL STORE

•COLOUR SYSTEM

•SOUND SYSTEM

•SEARCH

CHANNEL •18

•STORE

•

INSTALL

MANUAL STORE

•SOUND SYSTEM

•SEARCH

•CHANNEL

•STORE

G FINE TUNE F

•

INSTALL

MANUAL STORE

•COLOUR SYSTEM

•SOUND SYSTEM

•SEARCH

•CHANNEL

G STORE •

‰

•

INSTALL

MANUAL STORE

•COLOUR SYSTEM

•SOUND SYSTEM

•SEARCH

•CHANNEL

G STORE •

‰STORED

•

INSTALL

MANUAL STORE

•SEARCH

•CHANNEL

•STORE

•FINE TUNE

G PLL •

•

Sorting Channels

According to your preference, you can change the order of the stored

TV channels.

1Select SORT in the INSTALL menu.

2Press the cursor right to enter the menu.

3Key in the channel number in the FROM column you

want to swap from. Use the digit keys or the cursor

left/right.

4Press the cursor down and select TO.

5Key in the channel number in the TO column you want to

swap to.

6Press the cursor down and select EXCHANGE.

7Press the cursor right.

The message EXCHANGED appears and the selected

channels are exchanged.

8Repeat steps 3–7 until all TV channels are allocated as you

like.

9Press the MENU key to return to the INSTALL menu or

press the mkey to switch the menu off.

USING THE MENUS :INSTALL

INSTALL

•LANGUAGE FROM

•AUTO STORE TO

• MANUAL STORE EXCHANGE

•

FSORT

•CHANNEL EDIT

•

INSTALL

SORT

G FROM •

‰8

•TO

•EXCHANGE

INSTALL

SORT

•FROM

G TO •

‰6

•EXCHANGE

INSTALL

SORT

•FROM

•TO

G EXCHANGE •

‰EXCHANGED

INSTALL

SORT

•FROM

•TO

G EXCHANGE •

‰

Editing Channels

This feature allows you to edit or skip channels from the channel list

that have bad or weak signals or channels that you do not watch

often.

Note : Once a channel is skipped, you cannot select it with the CH –

or + key. You can only access the channel with the digit keys.

1Select CHANNEL EDIT in the INSTALL menu.

2Press the cursor right to enter the channel list.

3Select the channel you want to skip with the cursor

up/down.

4Press the cursor right to skip the selected channel.

The message SKIPPED is displayed.

5Press the cursor up/down to select another channel and

repeat step 4.

6Press the cursor left or the MENU key to return to the

INSTALL menu or the mkey to switch the menu off.

Note : To add back channels to the list, repeat steps 1–4 and

press the mkey to switch the menu off.

USING THE MENUS :INSTALL

INSTALL

•LANGUAGE 3

•AUTO STORE 4

• MANUAL STORE 5

• SORT 6

•

FCHANNEL EDIT •

‰7

•

INSTALL

•LANGUAGE 3

•AUTO STORE 4

• MANUAL STORE 5

• SORT 6

G CHANNEL EDIT •

•

INSTALL

•LANGUAGE 3

•AUTO STORE 4

• MANUAL STORE 5

• SORT 6

G CHANNEL EDIT •

F7 SKIPPED

•

Naming Channels

It is possible to assign a name to a TV channel. This feature allows

you to enter a name or modify an existing name of a channel, includ-

ing peripherals.

Note : Even when you have selected another language in the

LANGUAGE menu, only the English language character set is

offered to enter names to the TV channels stored.

1Select a TV channel or peripheral you want to assign a name

or modify the existing name.

2Select NAME in the INSTALL menu.

3Press the cursor right to enter the menu.

4Key in the selected character with the cursor up/down.

5Move to the next character with the cursor right and key in

the next character. You can key in up to a maximum of five

characters.

6Press the MENU key to store the named channel.

USING THE MENUS :INSTALL

INSTALL

•AUTO STORE

•MANUAL STORE

• SORT

• CHANNEL EDIT

G NAME •

‰PERSONAL

•INSTALL

•AUTO STORE

•MANUAL STORE

• SORT

• CHANNEL EDIT

G NAME •

‰PERSONAL

•

INSTALL

•AUTO STORE

•MANUAL STORE

• SORT

• CHANNEL EDIT

G NAME •

‰-

•

INSTALL

•AUTO STORE

•MANUAL STORE

• SORT

• CHANNEL EDIT

G NAME •

‰CNN

•

INSTALL

•AUTO STORE

•MANUAL STORE

• SORT

• CHANNEL EDIT

G NAME •

‰PERSONAL

•

USING THE MENUS :PICTURE

Picture Menu Items

Brightness

Allows you to adjust the brightness levels of the picture.

Colour

Allows you to adjust the colour saturation of the picture.

Contrast

Allows you to adjust the contrast levels of the picture.

Sharpness

Allows you to adjust the edge definition of the picture to improve details.

Hue (only with NTSC signals)

Allows you to adjust the colour mix of the picture.

Colour Temperature

Offers the options Normal, Warm, and Cool. Make your selection with the

cursor left/right. Normal keeps whites white. Warm makes whites reddish.

Cool makes whites bluish.

Digital Options

Digital Scan eliminates picture flickering and line jitter, offering a stable

picture for relaxed viewing (no eye strain). Progressive doubles the number

of visible picture lines per field by displaying all picture frame lines at once.

This minimizes the visibility of the scan lines. Auto detects the input signal

and provides the appropriate mode for the best picture performance. Choose

Digital Scan for PAL 50Hz signals and Progressive Scan for NTSC 60Hz

signals.

Dynamic Contrast

Automatically makes the contrast in the darker and the brighter picture

areas more noticeable as the image on screen changes. Normally, select

MED. In certain circumstances it may be preferable to select MIN, MAX,

or OFF.

Manual Converge

Allows you to adjust picture convergence.

Note : The picture settings Brightness, Colour, Contrast, Sharpness (Hue),

and Colour Temperature are stored separately for channels 0–11 and for

the external sources.

Accessing the Menu

1Press the MENU key to display the main menu.

2Select PICTURE.

3Press the cursor right to access the PICTURE submenu.

4Use the cursor in the up/down directions to select an item.

5Use the cursor in the left/right directions to make adjust-

ments or settings.

6Press the MENU key to return or press the mkey to switch

the menu off.

•

FPICTURE BRIGHTNESS

•SOUND COLOUR

• FEATURES CONTRAST

• INSTALL SHARPNESS

EDIT COLOUR TEMP

PICTURE

G BRIGHTNESS F30

•COLOUR

• CONTRAST

• SHARPNESS

•

COLOUR TEMP

•

DIGITAL OPTIONS

•

PICTURE

•

SHARPNESS

CONVERGE RED

•

COLOUR TEMP CONVERGE BLUE

•

DIGITAL OPTIONS MULTIPOINT RED

•

DYNAMIC CONTRAST MULTIPOINT BLUE

G MANUAL CONVERGE SAVE MULTIPOINT

•

Select

item

Return

Switch

off

USING THE MENUS :PICTURE

Using Manual Converge : Converge Red/Blue

Your projection TV has three color projection tubes : one for red, one

for green, and one for blue. When mixed in proper proportion, the

beams of light coming from the tubes can produce any color. To cre-

ate a clear picture, however, these color beams must be precisely

aligned. This alignment is called convergence. Bumps and vibrations,

moving the set, or the presence or magnetic fields can cause the color

beams to become improperly aligned, or misconverged, resulting in a

fuzzy picture. The Manual Converge controls allow you to adjust

picture convergence.

Note : Allow the TV to warm up for 20 minutes before adjusting conver-

gence.

1Select MANUAL CONVERGE in the PICTURE menu.

2Press the cursor down and select either CONVERGE RED

or CONVERGE BLUE.

Note : If various images in the picture have red outlines,

select CONVERGE RED. If various images in the picture

have blue outlines, select CONVERGE BLUE.

3Use the cursor right, left, up, or down to adjust the cross

hair until the color outline is gone. The adjustment is auto-

matically saved in the TV’s memory when you exit the

adjust mode.

4Press the MENU key to return or the mkey to switch the

menu off.

Check the TV picture. If any color outlines remain around

the images, use the MULTIPOINT RED (for red outlines)

or MULTIPOINT BLUE (for blue outlines) control. See

the next page for instructions for using those controls.

Converge Red

PICTURE

MANUAL CONVERGE

CONVERGE RED •

‰

•CONVERGE BLUE

•MULTIPOINT RED

•MULTIPOINT BLUE

•SAVE MULTIPOINT

•

USING THE MENUS :PICTURE

Using Manual Converge : Multipoint Red/Blue

The Multipoint Red/Blue convergence controls allow you to adjust

picture convergence at specific points on the TV screen.

Note : Allow the TV to warm up for 20 minutes before adjusting

convergence. Adjust Converge Red or Converge Blue before using

the Multipoint Red/Blue controls. See the previous page.

1Select MULTIPOINT RED or MULTIPOINT BLUE in

the MANUAL CONVERGE menu.

2Press the cursor right to enter navigate mode.

3Use the cursor left, right, up, or down to move to a cross

hair that has a color outline.

4Press the m(Status/Exit) key to enter adjust mode.

5Use the cursor left, right, up, or down to adjust the cross

hair until the color outline is gone.

6Press the mkey to return to navigate mode.

7Repeat steps 3–6 until all misaligned cross hairs have been

adjusted. Then press the MENU key.

8For your multipoint adjustments to be stored in the TV’s

memory, you must activate SAVE MULTIPOINT.

Note : If you are not satisfied with the adjustments you just

made and want to start over, you can use the UNDO

MULTIPOINT control. This control allows you to undo

the adjustments, but only if you use it before saving.

To save your multipoint adjustments : Select SAVE

MULTIPOINT and press the cursor left or right.

To undo your multipoint adjustments : Select UNDO

MULTIPOINT and press the cursor left or right.

To restore the TV’s picture convergence to factory settings,

select RESTORE FACTORY and press the cursor left or

right.

9Press the MENU key to return or the mkey to switch the

menu off.

to Navigate EXIT to Adjust

SAVE MULTIPOINT

UNDO MULTIPOINT

RESTORE FACTORY

PICTURE

MANUAL CONVERGE

•CONVERGE RED

•CONVERGE BLUE

MULTIPOINT RED •

‰

•MULTIPOINT BLUE

•SAVE MULTIPOINT

•

to Adjust EXIT to Navigateto Navigate EXIT to Adjust

to Adjust EXIT to Navigate

to Navigate EXIT to Adjust

to Adjust EXIT to Navigate

PICTURE

MANUAL CONVERGE

•CONVERGE RED

•CONVERGE BLUE

MULTIPOINT RED •

‰

•MULTIPOINT BLUE

•SAVE MULTIPOINT

•

PICTURE

MANUAL CONVERGE

•CONVERGE RED

•CONVERGE BLUE

•MULTIPOINT RED

•MULTIPOINT BLUE

SAVE MULTIPOINT •

‰

•

PICTURE

MANUAL CONVERGE

•CONVERGE RED

•CONVERGE BLUE

•MULTIPOINT RED

•MULTIPOINT BLUE

SAVE MULTIPOINT •

‰STORED

•

PICTURE

MANUAL CONVERGE

•CONVERGE BLUE

•MULTIPOINT RED

•MULTIPOINT BLUE

•SAVE MULTIPOINT

UNDO MULTIPOINT •

‰

•

PICTURE

MANUAL CONVERGE

•CONVERGE BLUE

•MULTIPOINT RED

•MULTIPOINT BLUE

•SAVE MULTIPOINT

UNDO MULTIPOINT •

‰RESTORED

•

PICTURE

MANUAL CONVERGE

•MULTIPOINT RED

•MULTIPOINT BLUE

•SAVE MULTIPOINT

•UNDO MULTIPOINT

RESTORE FACTORY •

‰

•

PICTURE

MANUAL CONVERGE

•MULTIPOINT RED

•MULTIPOINT BLUE

•SAVE MULTIPOINT

•UNDO MULTIPOINT

RESTORE FACTORY •

‰RESTORED

•

USING THE MENUS :SOUND

Sound Menu Items

Treble

Attenuates or amplifies the high-frequency response of the audio out-

put signal.

Bass

Attenuates or amplifies the low-frequency response of the audio out-

put signal.

Balance

Adjusts the balance of the right and left speaker’s sound output.

AVL (Automatic Volume Leveller)

Automatically controls the volume level to avoid excessive level dif-

ferences, especially when switching to another channel or during

commercial breaks.

Accessing the Menu

1Press the MENU key to display the main menu.

2Select SOUND with the cursor down.

3Press the cursor right to access the SOUND submenu.

4Use the cursor in the up/down directions to select an item.

5Use the cursor in the left/right directions to make adjust-

ments or settings.

6Press the MENU key to return or press the mkey to switch

the menu off.

•

FPICTURE BRIGHTNESS

•SOUND COLOUR

• FEATURES CONTRAST

• INSTALL SHARPNESS

EDIT COLOUR TEMP

• PICTURE TREBLE

•

FSOUND BASS

• FEATURES BALANCE

• INSTALL AVL

EDIT

SOUND

GTREBLE F59

• BASS

• BALANCE

• AVL

•

SOUND

• BASS

• BALANCE

• AVL

GBASS BOOST •

FOFF

•

Select

item

Return

Switch

off

USING THE MENUS :FEATURES

Accessing the Menu

1Press the MENU key to display the main menu.

2Select FEATURES with the cursor down.

3Press the cursor right to access the FEATURES submenu.

4Use the cursor in the up/down directions to select an item.

5Use the cursor in the left/right directions to make settings.

6Press the MENU key to return or press the mkey to switch

the menu off.

Activating the Timer

The Timer feature allows you to set the timer to switch to another

channel at a specified time while you are watching a channel or

when the TV is in standby mode. You can also set the TV to switch

off automatically at a specific time by setting a Stop Time.

1Select TIMER in the FEATURES menu.

2Press the cursor right to enter the Timer.

Setting the Timer

1Press the cursor right again to enter TIME mode.

2Key in the current time with the digit keys.

You must use 24-hour, or military, time. For example : 2:15

p.m. is 14:15.

If you entered an incorrect digit :

Complete the actual time with arbitrary numbers, then start

again.

3Press the cursor left to exit TIME mode.

Continue to the next page.

•

FPICTURE BRIGHTNESS

•SOUND COLOUR

• FEATURES CONTRAST

• INSTALL SHARPNESS

EDIT COLOUR TEMP

• PICTURE TIMER

•SOUND CHILD LOCK

•

FFEATURES FORMAT

• INSTALL ACTIVE CTRL

EDIT

FEATURES

•

FTIMER TIME

•CHILD LOCK START TIME

• FORMAT STOP TIME

• ACTIVE CTRL CHANNEL

EDI ACTIVATE

FEATURES

• TIMER

• CHILD LOCK

• FORMAT

G ACTIVE CTRL •

‰ON

EDIT

FEATURES

TIMER

GTIME •

‰--:--

•START TIME

• STOP TIME

• CHANNEL

• ACTIVATE

•

FEATURES

TIMER

GTIME •

‰14:15

•START TIME

• STOP TIME

• CHANNEL

• ACTIVATE

•

Select

item

Return

Switch

off

Setting Start Time

1Select START TIME with the cursor down.

2Press the cursor right to enter the START TIME mode.

3Key in the time you want the programme to be switched on.

4Press the cursor left to exit START TIME mode.

Setting Stop Time

1Select STOP TIME with the cursor down.

2Press the cursor right to enter the STOP TIME mode.

3Key in the time you want the programme to be switched off.

4Press the cursor left to exit STOP TIME mode.

Selecting the Channel

1Select CHANNEL with the cursor down.

2Select the channel you want to switch to.

Activating the Timer

1Select ACTIVATE with the cursor down.

2Press the cursor right to enter the ACTIVATE mode to acti-

vate the timer.

3Using the cursor right, select ONCE or DAILY, according to

if you want to activate the timer on the selected channel and

the selected time every day or only once.

Displaying the Time

1Select DISPLAY with the cursor down.

2Press the cursor right to select ON or OFF, according to if

you want to display the current time on the TV screen or not.

3Press the MENU key to return or the mkey to switch the

menu off.

USING THE MENUS :FEATURES

FEATURES

TIMER

• TIME

GSTART TIME •

‰--:--

• STOP TIME

• CHANNEL

• ACTIVATE

•

FEATURES

TIMER

•TIME •

‰12:30

GSTART TIME •

‰16:00

• STOP TIME

• CHANNEL

• ACTIVATE

•

FEATURES

TIMER

•TIME •

‰12:30

•START TIME •

‰13:30

GSTOP TIME •

‰18:00

• CHANNEL

• ACTIVATE

•

FEATURES

TIMER

• TIME

•START TIME

GSTOP TIME •

‰--:--

• CHANNEL

• ACTIVATE

•

FEATURES

TIMER

•TIME

•START TIME

• STOP TIME

GCHANNEL •

‰3

• ACTIVATE

•

FEATURES

TIMER

•TIME

•START TIME

• STOP TIME

GCHANNEL •

‰8

• ACTIVATE

•

FEATURES

TIMER

•TIME

•START TIME

• STOP TIME

•CHANNEL

GACTIVATE •

‰OFF

•

GACTIVATE •

‰ONCE

GACTIVATE •

‰DAILY

FEATURES

TIMER

•START TIME

• STOP TIME

•CHANNEL

•ACTIVATE

GDISPLAY •

‰ON

•

Activating the Child Lock

The Child Lock feature allows you to lock channels to prevent chil-

dren from watching certain programmes.

Entering the Access Code

1Select CHILD LOCK in the FEATURES menu.

2Press the cursor right to enter the ACCESS CODE.

3Key in the access code 0711 (the default access code).

A message INCORRECT will appear.

4Key in access code 0711 a second time.

The message CORRECT will appear and make the Child

Lock menu accessible.

Changing the Access Code

1Select CHANGE CODE to enter an access code of your

choice.

2Press the cursor right to enter the CHANGE CODE mode.

3Key in the access code of your choice and confirm it again.

The message CORRECT will appear.

Activating the Child Lock

1Select LOCK CHANNEL in the CHILD LOCK menu.

Note : Enter the access code if requested. See above.

2Press the cursor right to enter the LOCK CHANNEL

mode.

3Use the cursor up/down to select the channel you want to

lock.

4Press the cursor right to lock the channel.

A keylock symbol will appear beside the locked channel.

From now on the locked channel(s) can be accessed only

via the remote control.

5Repeat steps 1–4 to unlock a locked channel.

To clear all locked channels at once, select CLEAR ALL in

the CHILD LOCK menu and press the cursor right.

The message CLEARED will appear.

6Press the MENU key to return or the mkey to switch the

menu off.

USING THE MENUS :FEATURES

FEATURES

• TIMER ACCESS CODE

• CHILD LOCK ----

• FORMAT

• ACTIVE CTRL

EDIT

FEATURES

CHILD LOCK

• LOCK CHANNEL ENTER

G CHANGE CODE •

FNEW CODE

• CLEAR ALL XXXX

FEATURES

CHILD LOCK

• LOCK CHANNEL CONFIRM

G CHANGE CODE •

FCODE

• CLEAR ALL XXXX

FEATURES

CHILD LOCK

• LOCK CHANNEL CONFIRM

G CHANGE CODE •

FCODE

• CLEAR ALL XXXX

CORRECT

FEATURES

CHILD LOCK

• LOCK CHANNEL ENTER

G CHANGE CODE •

FNEW CODE

• CLEAR ALL ----

FEATURES

CHILD LOCK

G LOCK CHANNEL •

• CHANGE CODE 3

• CLEAR ALL 4

FEATURES

CHILD LOCK

G LOCK CHANNEL •

F3 Ç

• CHANGE CODE 4

• CLEAR ALL 5

FEATURES

CHILD LOCK

• LOCK CHANNEL

• CHANGE CODE

G CLEAR ALL •

FEATURES

CHILD LOCK

• LOCK CHANNEL

• CHANGE CODE

G CLEAR ALL •

FCLEARED

FEATURES

• TIMER ACCESS CODE

G CHILD LOCK XXXX

• FORMAT INCORRECT

• ACTIVE CTRL

EDIT

FEATURES

• TIMER ACCESS CODE

G CHILD LOCK XXXX

• FORMAT CORRECT

• ACTIVE CTRL

EDIT

Using the Keys on the TV

Should your remote control be lost or broken, you can still change

some of the basic picture and sound settings with the keys on the front

of the TV.

1Press the VOL %% and %%keys simultaneously to display/can-

cel the main menu.

2Press the CH %%ﬁﬁkeys to select a menu item.

3Press the VOL %%or%%key to display the submenu and adjust

the settings.

4Press the VOL %%and %%keys simultaneously and repeatedly

to return to the main menu or to back out of the menu.

When the menu is not being displayed, the CH %%ﬁﬁkeys

enable you to select TV channels, and the VOL %%and %%

keys allow you to adjust the volume.

USING THE MENUS :FEATURES

Selecting the Screen Format

The TV’s Screen Format options allow you flexibility in viewing

video sources. Select a screen format using the vor cursor up/down

keys or the onscreen menu. To use the onscreen menu :

1Select FORMAT in the FEATURES menu.

2Press the cursor right repeatedly to cycle through the differ-

ent screen formats and select your desired format. The

options vary by input source (see specifics to the right) :

•4:3 format displays the 4:3 picture using the full surface of

the screen.

•AUTO format make the picture fill the screen as much as

possible.

•EXPAND 4:3 format expands movie images recorded in

the letterbox format. The black bars at the top and bottom

of the screen are expanded, thus filling the entire TV

screen.

•COMPRESS 16:9 allows you to show widescreen, high-

definition video sources as they were intended for a more

natural picture. Black bars are displayed at the top and

bottom of the screen.

Switching Active Control™ on

Turn Active Control™ on using the remote key or the onscreen

menu. To use the onscreen menu :

1Select ACTIVE CTRL in the FEATURES menu.

2Press the cursor right to select ON to activate automatic con-

trol of Sharpness and Noise Reduction.

3Press the mkey to switch the menu off.

GFORMAT •

‰4:3

GFORMAT •

‰COMPRESS 16:9

GFORMAT •

‰AUTO

GFORMAT •

‰EXPAND 4:3

FEATURES

• TIMER

• CHILD LOCK

G FORMAT •

F4:3

• ACTIVE CTRL

EDIT

For AV1, CVI, AV2,

or AV3 Sources :

For AV4 1080i

Sources :

For AV4

480p or 576p Sources :

No picture format options are available through the TV.

Control the screen format at the source (DVD player or

digital set-top box).

GACTIVE CTRL •

‰OFF

FEATURES

• TIMER

• CHILD LOCK

• FORMAT

G ACTIVE CTRL •

‰ON

EDIT

USING PROGRAM LIST

USING SMART SURF

The Program List feature allows you to navigate a list of installed

channels, receive a quick overview of those available, and activate

the channel you desire.

1Press the PROGRAM LIST bkey.

2Cursor down to cycle through the list of installed channels

and highlight the channel number you want to activate.

The appearance of lock symbol means that a channel is

blocked by the Child Lock feature. See page 20.

3Cursor right to activate the channel you have selected.

4Press the mkey to switch the menu off.

Adding Channels to the Surf List

You can select a list or series of previously viewed channels with the

SURF key. This feature allows you to switch between different TV

programmes that currently interest you. You can have up to 10 chan-

nels in the SURF list. Five channels are shown in the list at one time.

Cursor down/up as necessary to see all the channels in the list.

1Select a channel you want to add to the Surf list.

2Press the SURF key.

3Cursor right to add the selected channel to the Surf list.

4Repeat steps 1–3 to add more channels to the Surf list.

5Press the mkey to switch the menu off.

6Press the SURF key repeatedly to cycle through channels.

Deleting Channels to the Surf List

1Press the SURF key.

2Press the SURF key again as many times as necessary to

select the channel you want to delete from the Surf list.

3Cursor right to delete the channel from the list.

4To delete more channels, repeat the steps above.

PROGRAM LIST

7 ACTIO

8 DRAMA

9 VIOLE Ç

•

‰10 ROMAN

11 - - - - -

SURF

•

F12 ADD?

SURF LIST EMPTY

SURF

•

F12 DELETE?

SURF

•

F24 ADD?

SURF

•

F24 DELETE?

SURF

•

F7 DELETE?

USING SMART PICTURE AND SMART SOUND

The Smart Picture feature offers you a choice of five picture settings :

Personal, Rich, Natural, Soft, and Multimedia. Smart Sound offers

you a choice of four sound settings : Personal, Voice, Music, and

Theatre.

Press the SMART `Picture or SMART ±Sound key on the

remote control repeatedly to cycle through the settings and select your

desired mode.

Smart Picture ``Options

Personal

Picture settings are based on your preference.

Rich

Emphasizes very vibrant colours. This option is desirable for AV

mode in a brightly lighted room.

Soft

Emphasizes “warm” colours. This option is desirable for a dimly

lighted room and gives a cinema-like effect when the light is

switched off.

Multimedia

Emphasizes “soft” colours. This option is desirable for playing com-

puter games.

Smart Sound ±±Options

Personal

Sound settings are based on your preferences.

Voice

Brings voices to the forefront, emphasizing them. Moves music to the

background.

Music

Emphasizes music over voices.

Theatre

Provides a balance between voices and music.

Note : The PERSONAL settings are the ones that you make using the

PICTURE or SOUND menus. These are the only Smart Picture and

Smart Sound settings that can be changed. All others are set at the

factory.

PERSONAL

BRIGHTNESS 50

COLOUR 50

CONTRAST 50

SHARPNESS 84

RICH

BRIGHTNESS 34

COLOUR 34

CONTRAST 89

SHARPNESS 84

NATURAL

BRIGHTNESS 34

COLOUR 34

CONTRAST 78

SHARPNESS 28

SOFT

BRIGHTNESS 34

COLOUR 34

CONTRAST 53

SHARPNESS 28

MULTIMEDIA

BRIGHTNESS 50

COLOUR 40

CONTRAST 40

SHARPNESS 70

PERSONAL

TREBLE 59

BASS 72

VOICE

TREBLE 56

BASS 47

MUSIC

TREBLE 62

BASS 69

THEATRE

TREBLE 59

BASS 72

USING THE SLEEP TIMER

Have you ever fallen asleep in front of the TV? Using the Sleep

Timer, you can program your TV to turn off while you sleep. This

feature allows you to set your TV to turn off within a certain amount

of time : 15, 30, 45, 60, 90, 120, 180, or 240 minutes.

Press the Sleep Timer key on the remote control. The Sleep Timer

onscreen display will appear on screen. Then within five seconds,

press the Sleep Timer key again as many times as necessary to select

the amount of time you want to pass before the TV will turn itself off.

An onscreen countdown will appear during the last minute before the

TV switches off. Ten seconds before the Sleep Timer switches the TV

off, GOOD BYE will be displayed on the TV screen.

Notes:

• To see how many minutes remain before the TV shuts itself off,

press the mkey.

• Changing the channel or volume during the last minute of a Sleep

Timer setting will cancel Sleep.

SLEEP OFF

SLEEP 15

TV SWITCHING OFF 59

TV SWITCHING OFF 9

GOOD BYE

The options are 15, 30, 45,

60, 90, 120, 180, or 240

minutes.

During the last minute of a

Sleep Timer setting, a count-

down will be displayed on

screen.

During the last 10 seconds

of a Sleep Timer setting,

“GOOD BYE” will be dis-

played on screen.

You can connect a wide range of video and audio equipment to your TV

in various ways. This page and the next one provide an overview of sig-

nal compatibilities and the types of equipment you can connect to the

sockets. Connection examples follow on subsequent pages. As necessary,

also refer to the handbook for peripheral equipment.

Overview : Standard Inputs/Outputs

1ANTENNA IN 75Ωsocket—compatible with the broadcast stan-

dard in your area. Use to connect radio-frequency (RF) signals

from VHF/UHF antennas or a cable system.

2YPbPr (component video input [CVI] sockets)—compatible

with 480i and 576i signals. Use to connect equipment having com-

ponent video outputs, such as DVD players, laser-disc players,

video-game players, satellite receivers, or other equipment. Use the

INPUT-AV 1 L(eft) and R(ight) AUDIO sockets for sound connec-

tions.

3S-VIDEO (super video) sockets—compatible with 480i and 576i

signals. Use to connect peripherals having Super VHS (S-VHS)

outputs, such as VCRs, DVD players, laser-disc players, video-

game players, satellite receivers, or other equipment.

VIDEO (composite) sockets

(INPUT-AV

1, INPUT-AV 2, and TV’s side socket panel

[AV3])—compatible with 480i and 576i signals. Use to connect

peripherals having composite video outputs, such as VCRs, video-

game players, or other equipment.

5AUDIO inputs (INPUT-AV 1, INPUT-AV 2, and TV’s side

socket panel [AV3])—use to connect from the audio output sock-

ets on VCRs, DVDs, or other peripherals.

6MONITOR OUT (VIDEO/AUDIO)—use to connect to a VCR

to record programmes from the TV. Or use the AUDIO outputs to

connect to an audio hi-fi system.

7SUBWOOFER Output—use to make optional connection to an

external powered subwoofer.

CONNECTING PERIPHERAL EQUIPMENT

VIDEO

S-VIDEO

AUDIO

G/Y

R/Pr

B/Pb

SYNC

AUDIO

AV4-480p/1080i-60Hz, 576p-50Hz

INPUT-AV 2 SUBWOOFERMONITOR

OUT

INPUT-AV 1

ANTENNA IN 75Ω

REAR OF TV

SIDE PANEL

Note : The

side panel is

AV3.

CONNECTING PERIPHERAL EQUIPMENT

The AV4 sockets allow you to connect digital equipment with

1080i/480p (60Hz) or 576p (50Hz) signal output.

Overview : High-definition Inputs

1AV 4 — use to connect digital equipment with a 1080i/480p

(60Hz) or 576p (50Hz) signal output, such as digital set-top

boxes or DVD players with progressive-scan capability. You

can connect equipment with YPbPr component video or RGB

outputs to the AV4 sockets. H and V Sync connections may or

may not be required for RGB connections. Use the AV4 L(eft)

and R(ight) AUDIO sockets for sound connections.

See the handbook for the digital equipment you are connecting.

VIDEO

S-VIDEO

AUDIO

G/Y

R/Pr

B/Pb

SYNC

AUDIO

AV4-480p/1080i-60Hz, 576p-50Hz

INPUT-AV 2 SUBWOOFERMONITOR

OUT

INPUT-AV 1

REAR OF TV

ANTENNA IN 75Ω

High-definition Inputs—Video Synchronizing Reference

Input Video Description Accepts Video Sync

according to :

AV4 480p (60Hz)

1080i (60Hz)

576p (50Hz)

EIA/CEA-770.2-C

EIA/CEA-770.3-C

ITU-R BT.1358

CONNECTING PERIPHERAL EQUIPMENT

Video Recorder : Playback

1Connect the RF cable to the RF socket on your video recorder.

Connect

another RF cable from the output of your video

recorder to the ANTENNA IN 75Ωsocket on your TV.

3Better playback quality can be obtained if you also connect the

Video, Audio Left and Right (only for stereo equipment) cables

to the VIDEO and AUDIO L (mono) and Rinputs of

INPUT-AV 2.

Note : In case of mono equipment, only the left loudspeaker

reproduces sound. Use a mono-to-stereo adaptor (not supplied)

for sound reproduction via the internal loudspeakers.

The MONITOR OUT connectors can be used for daisy chain-

ing or recording programmes from your TV. See page 28.

S-VHS-Video quality with an S-VHS video recorder is obtained

by connecting the S-VHS-Video cable with the S-VIDEO input

instead of connecting the video recorder to the VIDEO input.

See the handbook for the video recorder.

If You Do Not Make the Video and Audio

Connections in Step 3 Above :

Search for and store the test signal of the video recorder.

1Unplug the RF cable from the RF socket of your video recorder.

2Switch on your TV and put the video recorder on the test signal or

play a prerecorded tape. See the handbook for your video

recorder.

3Search for the test signal of your video recorder in the same way

you searched for and stored the TV signals. See pages 9–10.

4Store the test signal under programme number 0 or between 90

and 99.

5Replace the RF cable in the RF socket of your video recorder

after you have stored the test signal.

VIDEO

S-VIDEO

AUDIO

G/Y

R/Pr

B/Pb

SYNC

AUDIO

AV4-480p/1080i-60Hz, 576p-50Hz

AV5-RGB, 480p/1080i-60Hz, 576p-50Hz

INPUT-AV 2 SUBWOOFERMONITOR

OUT

INPUT-AV 1

ANTENNA IN 75Ω

VIDEO RECORDER

CABLE

A/V OUT

RF IN

RF OUT

REAR OF TV

VIDEO

S-VIDEO

LPb

VIDEO

S-VIDEO

AUDIO

G/Y

R/Pr

B/Pb

SYNC

AUDIO

AV4-480p/1080i-60Hz, 576p-50Hz

INPUT-AV 2 SUBWOOFERMONITOR

OUT

INPUT-AV 1

ANTENNA IN 75Ω

Video Recorder : Recording

To record S-VHS quality, connect an S-VHS peripheral directly to the

video recorder.

Recording a TV Programme

1Select the channel number on your video recorder.

2Set your video recorder to record.

See the handbook for your video recorder.

Switching channel numbers on your TV does not disturb recording.

Recording a Programme on Your Video Recorder Connected

to MONITOR OUT from Audio/Video Equipment Connected

to AV1,AV2, or to the Sockets on the Side of the TV (AV3)

1Switch on the equipment.

2Select the correct external source on your TV and on your

video recorder.

3Set your video recorder to record.

You record what you are watching on the screen.

Do not switch channel numbers and do not switch off your TV

when you are recording.

CONNECTING PERIPHERAL EQUIPMENT

Video Recorder and Other A/V Peripherals

1Connect the RF cable to the RF socket on your A/V peripheral

equipment.

2To obtain better picture quality, also connect the Video and

Audio left and Audio right (only for stereo equipment) cables to

the VIDEO and AUDIO L (mono) and AUDIO R input of the

INPUT-AV 2 sockets.

Note :

In case of mono equipment, only the left loudspeaker

reproduces sound. Use a mono-to-stereo adaptor (not supplied)

for sound reproduction via the internal loudspeakers.

3Connect the RF output of the A/V peripheral equipment to the

RF input on the video recorder.

4When a video recorder is not connected to MONITOR OUT

on your TV, you can record a programme only from the aerial

or from the cable system.

Only when a video recorder is connected to MONITOR OUT

is it possible to record a programme from other equipment con-

nected to the TV. See page 28.

Connect Video and Audio left (mono) and Audio right cables

from the video recorder A/V inputs to the VIDEO and

AUDIO L (mono) and AUDIO R sockets of the MONITOR

OUT on your TV.

5Connect from the RF output on the video recorder to the

ANTENNA IN 75Ωsocket on your TV.

DVD Player

Note : Progressive-scan DVD players can be connected to the AV 4 input

only.

1Connect the cables of your DVD player with component video

output to the Y-Pb-Pr INPUT-AV 1 sockets on your TV.

2Connect the cables from the Video and Audio (L and R) outputs

on the DVD player to the INPUT-AV 1 VIDEO and AUDIO L

(mono) and Rinputs on your TV.

See the handbook for your DVD player.

Note : The names of the component video sockets may differ

depending on the DVD player or digital source equipment used.

For example, besides YPbPr, you may see R-Y/B-Y/Y or

CrCbY. Although abbreviations and terms may vary, the letters

Band Rstand for the blue and red color component signal con-

nectors, respectively. The Yindicates the luminance signal. If

necessary, see the handbook for the digital equipment for more

information.

VIDEO

LPb

VIDEO

S-VIDEO

AUDIO

G/Y

R/Pr

B/Pb

SYNC

AUDIO

AV4-480p/1080i-60Hz, 576p-50Hz

INPUT-AV 2 SUBWOOFERMONITOR

OUT

INPUT-AV 1

ANTENNA IN 75Ω

VIDEO RECORDER

CABLE

A/V IN A/V OUT

VIDEO

S-VIDEO

LPb

VIDEO

S-VIDEO

AUDIO

G/Y

R/Pr

B/Pb

SYNC

AUDIO

AV4-480p/1080i-60Hz, 576p-50Hz

AV5-RGB, 480p/1080i-60Hz, 576p-50Hz

INPUT-AV 2 SUBWOOFERMONITOR

OUT

INPUT-AV 1

ANTENNA IN 75Ω

3RF OUT RF IN

A/V PERIPHERAL

RF IN

RF OUT

REAR OF TV

VIDEO

S-VIDEO

LPb

VIDEO

S-VIDEO

AUDIO

G/Y

R/Pr

B/Pb

SYNC

AUDIO

AV4-480p/1080i-60Hz, 576p-50Hz

AV5-RGB, 480p/1080i-60Hz, 576p-50Hz

INPUT-AV 2 SUBWOOFERMONITOR

OUT

INPUT-AV 1

ANTENNA IN 75Ω

DVD PLAYER

COMPONENT VIDEO

OUT

A/V OUT

REAR OF TV

VIDEO

S-VIDEO

LPb

VIDEO

S-VIDEO

AUDIO

G/Y

R/Pr

B/Pb

SYNC

AUDIO

AV4-480p/1080i-60Hz, 576p-50Hz

AV5-RGB, 480p/1080i-60Hz, 576p-50Hz

INPUT-AV 2 SUBWOOFERMONITOR

OUT

INPUT-AV 1

ANTENNA IN 75Ω

S-Video Equipment

Note : Progressive-scan DVD players can be connected to the AV 4

inputs only.

1Connect an S-VIDEO cable to the INPUT-AV 2 S-VIDEO

input.

2Connect the audio cables to the equipment’s AUDIO L (mono)

and AUDIO R sockets and to the INPUT-AV 2 AUDIO L

(mono) and AUDIO R sockets on your TV.

CONNECTING PERIPHERAL EQUIPMENT

AV4 Digital High-definition Inputs

When you have digital equipment with 1080i or 480p signal output

(60Hz) or 576p signal output (50Hz), connect it to the AV 4 inputs on

your TV. Examples of such equipment are digital set-top boxes and pro-

gressive-scan DVD players.

Connecting to AV4

Connect digital equipment with component video output (usually labeled

Y-Pb-Pr) or with RGB output (phono-type connectors) to the AV 4

inputs for video and audio left and right. Also connect to the Hand V

SYNC inputs on the TV if required for your digital equipment.

Note : The AV 4 sockets are compatible with some digital equipment hav-

ing RGB outputs with “sync on green” or RGB with “separate H and V

sync.” Output standards for digital equipment, however, may vary by

manufacturer. No industry standards have been established for HD televi-

sion RGB signal systems, timing, synchronization, and signal strengths. If

the digital equipment you want to connect to your TV offers both compo-

nent video and RGB outputs, component video is the suggested connec-

tion to use. See the handbook for the digital equipment.

Notes regarding connecting to either AV4 :

• For connections to either AV4, be sure the TV’s color-space setting

matches the output (Y-Pb-Pr or RGB) of the digital equipment you

have connected to the AV4 inputs. See instructions for setting the

TV’s color space on page 33.

• See the handbook for the high-definition equipment.

• If you notice scrolling images, wrong colors or no color, no picture or

even combinations of these on your screen, check to see if the connec-

tions have been done properly.

VIDEO

S-VIDEO

AUDIO

G/Y

R/Pr

B/Pb

SYNC

AUDIO

AV4-480p/1080i-60Hz, 576p-50Hz

INPUT-AV 2 SUBWOOFERMONITOR

OUT

INPUT-AV 1

ANTENNA IN 75Ω

DVD PLAYER

S-VIDEO OUTAUDIO OUT

REAR OF TV

VIDEO

S-VIDEO

AUDIO

G/Y

R/Pr

B/Pb

SYNC

AUDIO

AV4-480p/1080i-60Hz, 576p-50Hz

AV5-RGB, 480p/1080i-60Hz, 576p-50Hz

INPUT-AV 2 SUBWOOFERMONITOR

OUT

INPUT-AV 1

ANTENNA IN 75Ω

G/Y

R/Pr

B/Pb

SYNC

AUDIO

AV4-480p/1080i-60Hz, 576p-50Hz

VIDEO

S-VIDEO

AUDIO

G/Y

R/Pr

B/Pb

SYNC

AUDIO

AV4-480p/1080i-60Hz, 576p-50Hz

INPUT-AV 2 SUBWOOFERMONITOR

OUT

INPUT-AV 1

REAR OF TV

ANTENNA IN 75Ω

Additional Audio Connections : External Hi-fi

If you would like to hear TV programmes through your audio hi-fi

system, your TV offers this capability.

1Connect the audio cables to the AUDIO L and Rinput sockets

of your amplifier and to the AUDIO L (mono) and R

MONITOR OUT sockets of the TV.

2Turn the TV and audio system on.

3Control the volume of the hi-fi system at the hi-system’s ampli-

fier.

Volume adjustments made to the TV do not affect the volume

of the hi-fi system.

CONNECTING PERIPHERAL EQUIPMENT

Camera and Camcorder

Connect your camera or camcorder to sockets at the side of your TV.

1Connect the equipment to the VIDEO socket.

2Connect the equipment to the AUDIO L socket for mono or

both the AUDIO L and Rfor stereo.

TYPICAL

CAMCORDER

VIDEO

AUDIO

SIDE OF TV

VIDEO

S-VIDEO

AUDIO

G/Y

R/Pr

B/Pb

SYNC

AUDIO

AV4-480p/1080i-60Hz, 576p-50Hz

INPUT-AV 2 SUBWOOFERMONITOR

OUT

INPUT-AV 1

ANTENNA IN 75Ω

HI-FI AMPLIFIER

REAR OF TV

VIDEO

S-VIDEO

AUDIO

G/Y

R/Pr

B/Pb

SYNC

AUDIO

AV4-480p/1080i-60Hz, 576p-50Hz

AV5-RGB, 480p/1080i-60Hz, 576p-50Hz

INPUT-AV 2 SUBWOOFERMONITOR

OUT

INPUT-AV 1

ANTENNA IN 75Ω

CONNECTING PERIPHERAL EQUIPMENT

Additional Audio Connections : Surround Sound

Your TV has extra sockets that allow you to connect to an external

audio amplifier system and powered subwoofer. This connection will

provide a surround-sound experience similar to a movie theatre or

concert hall.

1Connect audio cables from the AUDIO L and R MONITOR

OUT sockets of the TV to the AUDIO L and Rinputs sockets

on the surround-sound amplifier.

2Connect speaker wires from the surround-sound amplifier’s

front and surround-sound speaker sockets to the front and sur-

round-sound speakers.

3Connect an audio cable from the SUBWOOFER output of the

TV to the Low Level Input sockets on the powered subwoofer.

4Adjust volume for the surround-sound amplifier and powered

subwoofer at those pieces of equipment.

AMPLIFIER POWERED

SUBWOOFER

REAR OF TV

VIDEO

S-VIDEO

AUDIO

G/Y

R/Pr

B/Pb

SYNC

AUDIO

AV4-480p/1080i-60Hz, 576p-50Hz

INPUT-AV 2 SUBWOOFERMONITOR

OUT

INPUT-AV 1

ANTENNA IN 75Ω

VIDEO

S-VIDEO

AUDIO

G/Y

R/Pr

B/Pb

SYNC

AUDIO

AV4-480p/1080i-60Hz, 576p-50Hz

INPUT-AV 2 SUBWOOFERMONITOR

OUT

INPUT-AV 1

ANTENNA IN 75Ω

(Center Speakers)

Front

Speaker

Front

Speaker

Powered

Subwoofer

Rear

Speaker

Rear

Speaker

Note: The gray circle indicates the primary viewing area.

CONNECTING PERIPHERAL EQUIPMENT

AV4

•PICTURE LANGUAGE

•SOUND AUTO STORE

•FEATURES MANUAL STORE

•

‰INSTALL SORT

CHANNEL EDIT

GAV4 •

‰RGB

INSTALL

•AUTO STORE

•MANUAL STORE

•SORT

•CHANNEL EDIT

GAV4 •

‰YPbPr

•

For AV4:

Setting the AV4 Colour Space

The term colour space refers to how colours are defined and appear

on your TV. When making connections to the AV 4 sockets, you will

need to be sure the TV’s colour space is set to match the output of the

peripheral you have connected.

1Press the AV key on the remote control as many times as neces-

sary to select the high-definition input you desire, AV4.

2Press the MENU key to display the menu.

3Select INSTALL with the cursor down.

4Press the cursor right to enter the INSTALL menu.

5Cursor down until the high-definition input (AV 4 ) is selected.

6The current colour-space setting appears to the right of AV4. To

change the setting, cursor left or right.

7Press the mkey to switch the menu off.

SELECTING CONNECTED EQUIPMENT FOR VIEWING

Equipment Connected with an Aerial Cable Only

Select the channel number under which you have stored the test signal

with the digit keys.

Equipment Connected to the back or to the side

of the TV (AV3)

Press the AV key repeatedly to select AV1, CVI, AV2, AV3, or AV4,

according to where you connected your equipment at the back or the side

of your TV.

Select CVI to view the playback of DVD discs if you used the INPUT-

AV 1 component video input sockets (Y-Pb-Pr and AUDIO L [mono]

and R inputs).

TV Channels

Enter the channel number of the TV channel you want to watch with the

digit or CH +/– keys.

WARNING Concerning Stationary Images on the TV Screen :

Do not leave stationary or “letterbox” images on screen for extended periods of time.This can cause

uneven picture-tube aging.

Normal use of the TV should involve the showing of pictures that contain constantly moving and changing images that fill the

screen. Be careful not to leave nonmoving images on screen for extended periods of time or to display the same images on screen

too frequently, because subtle ghost images can be left on the picture tubes. Avoid showing the same stationary images more than

15 percent of your total viewing in any one week. Sources of stationary images may be DVD discs, laser discs, video games, CD-i

discs, videotapes, digital television boxes, broadcast channels, cable channels, satellite channels, and others. Here are some exam-

ples of stationary images (this is not an all-inclusive list; you may encounter others in your viewing) :

•DVD menus—listings of DVD disc content

•“Letterbox” black borders—black bars shown along the edges of the picture when a widescreen (16:9) movie is played on TV

•Video-game images and scoreboards

•Television station logos—present a problem if they are bright and stationary; moving or low-contrast graphics are less likely to

cause uneven aging of the picture tube

•Stock-market tickers—presented at the bottom of the TV screen

•Shopping channel logos and pricing displays—bright and shown constantly or repeatedly in the same location on the TV

screen.

All picture tubes age with use, with their light output diminishing over time. But by maintaining normal use—mixing television

picture types—you will create conditions for the tubes to age at an even rate. The result will be a TV picture that is evenly bright

over the entire screen.

PLACEMENT OF THE TV

• See page 4.

CLEANING

• To avoid possible shock hazard, be sure the TV is unplugged from the electrical outlet before cleaning.

• Regularly dust the TV with a dry, nonscratching duster to keep the TV clean.

• When cleaning the TV, take care not to scratch or damage the screen surface. Avoid wearing jewelry or using anything abrasive.

Do not use household cleaners. Wipe the front screen with a clean cloth dampened with water. Use even, easy, vertical strokes

when cleaning.

• Gently wipe the cabinet surfaces with a clean cloth or sponge dampened in a solution of cool, clear water and a mild soap or

detergent. Use a clean, dry cloth to dry the wiped surfaces.

• Occasionally vacuum the ventilation holes or slots in the back cover of the set.

• Never use thinners, insecticide sprays, or other chemicals on or near the cabinet, as they might cause permanent marring of the

cabinet finish.

TIPS

• Do not shift or move the set around when it is switched on. Unevenness in colour in some parts of the screen may occur.

END-OF-LIFE DISPOSAL OF THE TV

Philips is paying much attention to making its products environmentally friendly. Your new TV contains materials that can be recy-

cled and reused. Specialised companies can dismantle your discarded TV at the end of its life, concentrating on the reusable materi-

als and minimising the amount of materials to be disposed. Please be sure to dispose of your old TV according to local regulations.

DISPOSAL OF EXHAUSTED BATTERIES

The batteries supplied do not contain the heavy metals mercury and cadmium. Nevertheless, in many countries exhausted batteries

may not be disposed of with your household waste. Please ensure you dispose of exhausted batteries according to local regulations.

CARE,CLEANING,AND TIPS

BEFORE CALLING SERVICE

motpmyS odottahW

TV remote control does not

work

• Check that the batteries are installed correctly.

• Replace the batteries, if necessary.

• Clean the remote control and the remote-sensor window on the TV.

• Be no farther than 6 meters from the TV when using the remote control and aim the remote

toward the TV’s remote-sensor window.

• If the remote still will not work, use the keys on the TV.

No power • Check that the TV’s power cord is plugged into the mains socket. If there is still no power, discon-

nect the plug. Wait for 60 seconds and reinsert the plug and then switch on the TV again.

• See if the outlet is controlled by a wall switch.

• If you are using an AC power strip, be sure the fuse on the power strip is not blown.

No picture • Check the antenna connection at the rear of the TV to see if it is properly connected to the TV

input terminal.

• The broadcast station may be experiencing difficulty. Try another channel.

• Adjust the contrast and brightness settings or select another picture setting with the Smart Picture

key on the remote control.

• If using peripheral equipment through the A/V inputs, be sure it is properly connected.

• Be sure you have selected the correct signal source for viewing.

• If you are attempting to view a picture from a progressive-scan-capable DVD player connected to

the AV4 sockets, be sure you have switched the DVD player to progressive-scan mode.

• If you are using an HD receiver, be sure its output is set correctly (to HD or SD), based on the

connection to the TV you have made.

Snowish picture and noise • Check the antenna connection.

Colour patch (unevenness) • Switch off the TV by the mains power key. Wait for 20 minutes before switching on again.

• Be sure you have made connections correctly.

• If you have connected digital equipment to the AV4 sockets, check the colour-space setting on the

equipment or TV and change the setting on either if necessary.

• Check to be sure the TV is not placed too near speakers or magnetic objects.

• Adjust the TV’s convergence.

Horizontal dotted lines • This may be caused by electrical interference from appliances such as hair dryers or vacuum

cleaners or other sources such as neon lights. Turn off the appliance or move the TV.

One white line across the screen • Switch the TV off immediately and consult a qualified service person.

Good picture but no sound • Increase the volume.

• Check that the TV is not muted; press the Hkey on the remote control.

• When no signal is detected, the TV automatically switches off the sound. This is proper operation

and does not indicate a malfunction.

• Check the transmission system’s sound settings on the set.

Good sound but poor colour or

no picture

• Adjust the contrast and brightness setting or select another picture setting with the Smart Picture

key on the remote control.

• Check the transmission system’s colour settings on this set.

Poor picture • Poor picture quality sometimes occurs when an S-VHS camera or camcorder has been connected

to the side panel (AV3) of the TV when another peripheral is connected to AV1 or AV2 simultane-

ously. In this case, switch off one of the other peripherals.

Double images or “ghost” images • High-rise building or hills may be obstructing reception. Try using a highly directional antenna to

improve the picture.

NICAM sound distortion

(crackling noise)

• This could be due to antenna siting or reflected signal.

• Switch over to “MONO” by pressing the I-II key on the remote control.

If your problem is not solved, switch the TV off and then back on again once. Never attempt to repair a defective TV yourself. Check with

your dealer or call a TV technician.

SPECIFICATIONS

Picture/Display

• Aspect Ratio: 4:3

• Display Technology: Projection TV, CRT, 7" liquid cooled

• Picture Enhancement: Active Control, APAC, Black Stretch, Blue Stretch,

Digital Comb Filter, Color Temperature, Digital Crystal Clear, Digital Noise

Reduction, Dynamic Contrast, Progressive Scan, 100Hz Digital Scan

• Screen Enhancements: Saphlon Screen, Anti- Aging Circuit, Anti-Reflection,

High Brightness, High Contrast

• Size: 43"

Supported Display Resolution

• Computer Formats: 640 x 480, 60Hz

• Video Formats: 480i 60Hz, 480p 60Hz, 576i 50Hz, 576p 50Hz, 1080i 60Hz

Sound

• Bass Enhancement: Bass Boost

• Output Power (RMS): 30 watt RMS

(50Hz-10kHz at 5% THD)

• Sound Enhancement: Automatic

Volume Leveler

• Speaker Size: 4"x6"

• Speaker Number: 2

• Speaker Type: full range oval

Tuner/Reception

• Aerial Input: 75 Ohm IEC-Type

• Auto Store: Yes

• Standards: NTSC M (3.58-4.5), NTSC (4.43-5.5), PAL B/G, PAL D/K, PAL I,

SECAM B/G, SECAM D/K, SECAM K1

Connectivity

• AV1: 480i 60Hz, 576i 50Hz, CVBS in, YPbPr, Audio L/R in

• AV2: 480i 60Hz, 576i 50Hz, CVBS in, S-Video Y/C, Audio L/R in

• AV3: Side, 480i 60Hz, 576i 50Hz, CVBS in, Audio L/R in

• AV4: 1080i 60Hz, 480p 60Hz, 576p 50Hz,

YPbPr, RGB+H/V

• Output Rear: Subwoofer out, CVBS out, Audio L/R out

Convenience

• Child Protection: Child Lock, Parental Control

• Clock Functions: Clock, Sleep Timer

• Convenience Enhancements: Auto Program, Auto Picture Modes, Auto

Sound Modes

• Menu Languages: Chinese-Simplified, English

• Picture Functions: Freeze

• Remote Control: RCS82D, Batteries

Dimensions

• Product Dimensions (WxHxD): 96 cm x

115 cm x 53 cm

• Product Weight: 57 kg

• Carton Dimensions: 106 cm x 125 cm x

62 cm

• Weight incl. Packaging: 65 kg

Power

• Complies with Energy Star, less than

1 watt standby

• Mains Power: 160-276V, 50-60Hz

• Power Consumption: 180 watts average

These technical specifications are subject to change without notice.

INDEX

aactive control, 7, 21

automatic tuning of channels, 9

bbilingual broadcast (I-II key), 7

ccamcorder, 31

child lock, 20

ddolby* virtual, 6

DVD, 29–30

dynamic contrast, 14

eediting channels, 12

ffreeze, 7, 26

frequency, 10

iinformation on screen (i+ key), 6

interrupt the sound (mute key), 7

mmanual installation, 9–10

menu language, 8

nnaming channels, 13

ppicture adjustments, 14

rrecording, 28–29

sscreen format, 21

sleeptimer, 24

smart picture and smart sound, 23

sorting channels, 11

sound adjustments, 17

stereo (I-II key), 7

storing TV channels, 9–10

S-VHS, 28, 31

Switching the TV on, 4

ttroubleshooting (before calling service), 36

vvideo recorder, 27–29

volume, 6

*Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

INTERNATIONAL GUARANTEE

CONSUMER INFORMATION CENTRES

Philips DFU D 43pp8445 93 Eng

43PP8445/93 43pp8445_93_dfu_eng Philips 43PP8445/93 user manual - English, Pdf file (203 Kb) - Owner's / User's manual

43PP8446/93 43pp8446_93_dfu_eng Philips 43PP8446/93 user manual - English, Pdf file (1.51 Mb) - Owner's / User's manual

43PP8447/93 43pp8447_93_dfu_eng Philips 43PP8447/93 user manual - English, Pdf file (1.51 Mb) - Owner's / User's manual

Navigation menu

Versions of this User Manual:

Views

Navigation