Philips MNT89 GCX Mounting Assembly Installation Guide User Manual Product Brochure Intelli Vue MX500/MX550 Solution 2da69ce1ebfe46e0b48ba77c0147169c
User Manual: Philips MNT89 Product Brochure Philips IntelliVue MX500/MX550 Mounting solution Philips - IntelliVue MX400/MX450 Dräger Apollo Anesthesia MachineMNT89
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide VHM Arm with 8'' Extension & Swivel Stop for Mounting Philips IntelliVue MP60/70, MX400/450/500/550/600/700/800 on Dräger Apollo Left Side The purpose of this guide is to describe mounting of Arm on left side of machine. WARNING: USE OF MOUNTING HARDWARE AND MONITORING COMPONENTS OTHER THAN THOSE DESCRIBED IN THIS DOCUMENT MAY RESULT IN SERIOUS INJURY DUE TO TIPPING OF THE ANESTHESIA MACHINE. WARNING: ALL DEVICES AND MOUNTING EQUIPMENT SHOULD BE POSITIONED INWARD, CLOSE TO THE APOLLO, DURING TRANSPORT. Installer: When installation is completed, provide these instructions and all related documentation to the end user for future reference. Parts Reference The following parts and hardware are included with this installation kit (hardware not shown): Item # Description Qty 1 VHM Arm with 8'' Extension 1 2 Nut Plate 2 3 M6 x 25mm Flat Head Socket Cap Screw (FHSCS) 2 4 Locking Lever, Height Adjustment 1 5 Cable Guide 1 6 Down Post, 6'' 1 7 #10-32 x 3/8'' Socket Head Cap Screw (SHCS) 3 8 M6 x 8mm FHMS 2 9 M6 x 12mm FHMS 1 10 5/32'' Hex Wrench 1 11 1/2'' Socket Wrench 1 VHM Arm with 8'' Extension 6'' Down Post Height Adjustment Locking Lever Table Mount (Supplied by Philips) **Cable Guide ** See DU-WS-0001 page 6 for Cable Management Tools Required: 5/32'' hex wrench (provided), Phillips Screwdriver 1/2'' socket wrench (provided). DU-AG-0018-94 Rev C 12/2/13 GCX Corp Page 1 of 4 Attaching Down Post to VHM Arm 1. Remove plastic bolt cap from Swivel Cup (not shown). 2. Using the 5/32'' hex wrench provided, fasten Post to Swivel Cup with three (3) #10-32 x 3/8'' SHCS as shown below. Swivel Cup #10-32 x 3/8'' SHCS (3) 6'' Down Post Mounting the Arm in the Accessory Track 1. Thread one (1) M6 x 25mm FHSCS a few turns into each Nut Plate (right). M6 x 25mm FHSCS (2) 2. Insert Nut Plate/screw assemblies in top and bottom slots of Channel Slide (rear of Arm), holding bottom screw in place to prevent it from falling from the slot. Nut Plate (2) 3. Hold Nut Plates in slots (below left) and guide entire assembly to top of track. 4. Using the 5/32'' hex wrench provided, tighten two (2) flat head socket cap screws (below right). Insert Nut Plates/Screws into Slots and Guide Nut Plates into Track Tighten Screws Slide Positioning Arm in Track DU-AG-0018-94 Rev C 12/2/13 GCX Corp Page 2 of 4 WARNING: Do not attempt to remove the Arm from the track while an instrument is mounted. While *supporting the weight of the mounted instrument, loosen the two (2) flat head socket cap screws (FHSCS) in the Slide. A 5/32'' hex wrench is provided for this task. Push up or pull down at the end of the arm nearest the Slide. Tighten screws to secure Arm in track. * It may be necessary to dismount instrument before adjusting Arm in track. FHSCS (2) Attaching the Philips Table Mount to the Mounting Adapter 1. Fasten the Philips-supplied Table Mount to the Mounting Adapter on the VHM Arm with one (1) M6 x 12mm FHMS and two (2) M6 x 8mm FHMS as shown below. M6 X 8mm FHMS (2) M6 X 12mm FHMS (1) Table Mount *Supplied by Philips Mounting Adapter Mounting the Monitor on the Arm (Table Mount) 1. Thread the Height Adjustment Locking Lever into the mounting hole in the right side of the Arm (right). 2. Mount monitor according to Philips table mount instructions. 3. Perform counterbalance adjustment in accordance with Section 3.0 of "Installation & Operation Manual for VHM™ Series Arms" (DU-WS-0001). Height Adjustment Locking Lever Mounting the MX400/450/500/550 Monitor (Fixed Mount Adapter) 1. Thread the Height Adjustment Locking Lever into the mounting hole in the right side of the Arm (right). 2. Mount the monitor in accordance with separate Installation Guide DU-PH-0073-15 provided with the Mounting Adapter, ordered separately. 3. Perform counterbalance adjustment in accordance with Section 3.0 of "Installation & Operation Manual for VHM™ Series Arms" (DU-WS-0001). DU-AG-0018-94 Rev C 12/2/13 GCX Corp Page 3 of 4 VHM Arm Operation and Adjustment Refer to "Installation & Operation Manual for VHM™ Series Arms" (DU-WS-0001). Routine Maintenance Periodically check all mounting hardware. Tighten as necessary for optimal operation. Cleaning the Mounting Assembly CAUTION: GCX makes no claims regarding the efficacy of the listed chemicals or processes as a means for controlling infection. Consult your hospital’s infection control officer or epidemiologist. To clean or sterilize mounted instruments or accessory equipment, refer to the specific instructions delivered with those products. 1. The mounting assembly may be cleaned with most mild, non-abrasive solutions commonly used in the hospital environment (e.g. diluted bleach, ammonia, or alcohol solutions). 2. The surface finish will be permanently damaged by strong chemicals and solvents such as acetone and trichloroethylene. 3. Do not use steel wool or other abrasive material to clean the mounting assembly. 4. Damage caused by the use of unapproved substances or processes will not be covered by warranty. We recommended that you test any cleaning solution on a small area of the arm that is not visible to verify compatibility. 5. Never submerge or allow liquids to enter the arm. Wipe any cleaning agents off of the arm immediately, using a waterdampened cloth. Dry the arm thoroughly after cleaning. DU-AG-0018-94 Rev C 12/2/13 GCX Corp Page 4 of 4
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : Nicole Company : GCX Create Date : 2013:12:11 08:35:34-08:00 Modify Date : 2013:12:11 08:35:39-08:00 Source Modified : D:20131211050121 Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2013:12:11 08:35:39-08:00 Creator Tool : Acrobat PDFMaker 10.1 for Word Document ID : uuid:0492b9b4-471a-40e7-aa0e-cf03c2c7c734 Instance ID : uuid:9b1c8031-7823-4095-8434-7f0f24d21d7f Subject : 2 Format : application/pdf Title : GCX Mounting Assembly Installation Guide Creator : Nicole Producer : Adobe PDF Library 10.0 Page Layout : OneColumn Page Count : 4EXIF Metadata provided by EXIF.tools