Pioneer K071 Bluetooth module User Manual Manual

Download:
Mirror Download [FCC.gov]
Document ID	1959263
Application ID	kIrwCptsJrVVonrxtjsPkQ==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	61.43kB (767865 bits)
Date Submitted	2013-05-07 00:00:00
Date Available	2013-05-07 00:00:00
Creation Date	2013-04-25 19:25:51
Producing Software	Microsoft® Word 2010
Document Lastmod	2013-04-25 19:25:51
Document Title	Manual
Document Creator	Microsoft® Word 2010
Document Author:	ZhangLi

X-8075 Bluetooth Module Manual
Version 1.0
1. Product Introduction
X-8075 is a fully integrated Bluetooth Module used as Car kit or in the Car
Audio System or any systems requiring complete embedded Bluetooth
connectivity solution. It’s a high quality solution with low cost. It will work as a
master or slave Bluetooth device, accepting the role switch request of remote
device automatically.
X-8075 Shape
X-8075 Support Features:
Embedded Bluetooth 3.0 via EDR
Pairing and connection with multiple Bluetooth devices
Make calls, Terminate calls, Private mode, 3-way calling
Phone book and Call history synchronization
Audio Streaming
New message notification
2. Common Specification
Radio Chip:
CSR BC5MM
Power Supply Voltage:
The operating voltage range is D.C. 3.1V-3.6V.
Rated voltage is D.C.3.3V.
Ambient temperature:
The operating temperature range is －40～＋85 ﾟ C.
Rated temperature is ＋25 ﾟ C.
Humidity:
The maximum relative humidity is 95 % (Ta=45 ﾟ C).
Rated relative humidity is 65%.
Antenna:
Built-in
Antenna gain:
The antenna gain value is -1dBi.
3. Hardware Integration
X-8075 Pin-out diagram
No.
symbol
UART_RX
UART DATA OUTPUT
UART_TX
UART DATA INPUT
SPI_MISO
SPI data output
SPI_MOSI
SPI data input
3V3
explain
Description
power Vcc 3.3V
Reset if low.Input debounced so must be low for >5ms to cause
RST_BT#
a reset
1V8
power
1.8V
1V8
power
1.8V
1V8_EN
10
GND
11
LINEOUT_L
1V8 power supply enable signal --active high
GND
analog audio output
12
LINEOUT_R
analog audio output
13
MIC2_N
Microphone2 minus input
14
MIC2_P
Microphone2 plus input
15
MIC_BIAS
16
MIC1_P
Microphone1 plus input
17
MIC1_N
Microphone1 minus input
18
GND
19
SPI_CBS
Chip select for serial peripheral interface(SPI),active low
20
SPI_CLK
SPI clock
21
PCM_SYNC
synchronous data sync
22
PCM_CLK
synchronous data clock
23
PCM_IN
synchronous data input
24
PCM_OUT
Microphone
bias
GND
synchronous data output
X-8075 Pin-out Description
4. Software Interface Reference
The default device name is X-8075_B203 after module start. User can change
it to any other friendly name by using the relative interface command. X-8075
can send or receive data from remote Bluetooth device.
Software Configuration:
Setting
Value
Baud Rate
115200bps(pre-configurable)
Data bit
8 data bits, list significant bit transmit first
Parity
Even Parity
Stop bit
1 stop bit
HW Flow Control
Optional
Interface Example:
Name:
BT_GEN_FID_SET_SCANMODE_REQ
functionality:
Set Bluetooth inquiry scan and page scan parameter
param 1:
type:
u8
name:
meaning:
discoverable mode
range:
0x00~0x03
discover_mode
0x00: no scan enable(default)
0x01: Enable inquiry scan Page scan disabled
0x02: Enable page scan inquiry scan disabled
0x03: page and inquiry enable
The interface command name is BT_GEN_FID_SET_SCANMODE_REQ. There
is one paramer named discover_mode with four valid values and below is the
description of all values.User can configure ScanMode of X-8075 by sending this
interface. When Host Controller initiates a REQ, BT Module should always send a
corresponding CFM to specify operation result and optional additional information.
Example:
BT_GEN_FID_SET_SCANMODE_REQ
BT_GEN_FID_SET_SCANMODE_CFM
Set discover_mode as 0x03, then other Bluetooth device can find X-8075 and initiate
to pairing with X-8075.
Interface Listing
No.
Interface
BT_GEN_FID_RESET_REQ
BT_GEN_FID_INQUIRY_REQ
BT_GEN_FID_SET_SCANMODE_REQ
BT_GEN_FID_SET_SEC_MODE_REQ
BT_GEN_FID_GET_REMOTE_NAME_REQ
BT_GEN_FID_SET_LOCAL_NAME_REQ
BT_GEN_FID_READ_LOCAL_NAME_REQ
BT_GEN_FID_PAIRING_DEVICE_REQ
BT_GEN_FID_DEL_PAIR_DEV_REQ
10
BT_GEN_FID_GET_PAIR_DEV_LIST_REQ
11
BT_GEN_FID_SERVICE_CON_REQ
12
BT_GEN_FID_SERVICE_DISCON_REQ
13
BT_GEN_FID_GET_LINK_QUALITY_REQ
14
BT_GEN_FID_SEARCH_ATTRIBUTE_REQ
15
BT_GEN_FID_TEST_MODE_REQ
16
BT_GEN_FID_ENTER_DFU_REQ
17
BT_HFP_FID_AUDIO_TRANSFER_REQ
18
BT_HFP_FID_DIAL_REQ
19
BT_HFP_FID_LAST_DIAL_REQ
20
BT_HFP_FID_MEM_DIAL_REQ
21
BT_HFP_FID_CALL_PROCESS_REQ
22
BT_HFP_FID_TERMINATE_CALL_REQ
23
BT_HFP_FID_GET_CURRENT_CALL_LIST_REQ
24
BT_HFP_FID_VOICE_RECOGNIZE_REQ
25
BT_HFP_FID_DTMF_CODE_REQ
26
BT_HFP_FID_CALL_HOLD_REQ
27
BT_HFP_FID_SUBSCRIBER_NUM_REQ
28
BT_HFP_FID_NETWORK_OPERATOR_REQ
29
BT_AVP_FID_MEDIA_START_REQ
30
BT_AVP_FID_MEDIA_PAUSE_REQ
31
BT_AVP_FID_GET_PLAY_STATUS_REQ
32
BT_AVP_FID_GET_ELEMENT_ATTRIBUTES_REQ
33
BT_PBDL_FID_CONFIGURE_REQ
34
BT_PBDL_FID_SYNC_PB_REQ
35
BT_PBDL_FID_SYNC_ABORT_REQ
36
BT_PBDL_FID_GET_PB_BY_INDEX_REQ
37
BT_PBDL_FID_SEARCH_PB_BY_NUMBER_REQ
38
BT_PBDL_FID_SEARCH_PB_BY_KEY_REQ
System Error Status
Value
Error Status
0x00
APP_EVTRES_SUCCESS
0x01
APP_EVTRES_FAIL
0x02
APP_EVTRES_UNKNOWN_OPCODE
0x03
APP_EVTRES_ILLEGAL_PARAM
0x04
APP_EVTRES_OPERATION_FAIL
0x05
APP_EVTRES_SYSTEM_BUSY
0x06
APP_EVTRES_ILLEGAL_OPERATION
0x07
APP_EVTRES_ILLEGAL_STATE
0x08
APP_EVTRES_ILLEGAL_FORMAT
0x09
APP_EVTRES_PAGE_TIMEOUT
0x0A
APP_EVTRES_ABNORMAL
0x0B
APP_EVTRES_ABORTED
0x0C
APP_EVTRES_SDP_ERROR
0x0D
APP_EVTRES_AUTHENTICATION_FAIL
0x0E
APP_EVTRES_OPERATION_TIMEOUT
0x0F
APP_EVTRES_NO_CORRESPONDING_IND
1. Reset Software
Name:
BT_GEN_FID_RESET_REQ
functionality:
Software reset of the Bluetooth Module.
2, Inquiry Remote Device
Name:
BT_GEN_FID_INQUIRY_REQ
functionality:
Inquiry Bluetooth device(s) nearby. The detail device information should be report to host
application by the indication of BT_GEN_FID_INQ_RESULT_IND.
param 1:
type:
u8
meaning:
The mode of inquiry Bluetooth device(s)
range:
0x00~0x01
0x00: General inquiry
name:
mode
0x01: Limited inquiry
param 2:
type:
u24
name:
meaning:
Bitwise class of device to be filtered
range:
0x000000~0xFFFFFF
filter
param 3:
type:
u8
name:
duration
meaning:
The maximum amount of time used for inquiring in 1.28 second
range:
0x02~0x30
param 4:
type:
u8
name:
meaning:
The maximum number of response from the inquiry
range:
0x01~0x20
num
3. San Mode configure
Name:
BT_GEN_FID_SET_SCANMODE_REQ
functionality:
Set Bluetooth inquiry scan and page scan parameter
param 1:
type:
u8
meaning:
discoverable mode
range:
0x00~0x03
0x00: no scan enable(default)
0x01: Enable inquiry scan Page scan disabled
0x02: Enable page scan inquiry scan disabled
0x03: page and inquiry enable
4. Security Mode configure
Name:
BT_GEN_FID_SET_SEC_MODE_REQ
functionality:
Configure the security mode of local Bluetooth device
param 1:
type:
u8
name:
meaning:
The Bluetooth security mode
range:
0x01~0x04
mode
0x01: non secure
0x02: service level enforced security
0x03: link level enforced security 0x04: service level enhanced security(SSP, default)
param 2:
type:
u8
name:
meaning:
The Bluetooth encryption mode
range:
0x00~0x02
sec
0x00: Encryption off
0x01: Point to point encryption
0x02: Point to point and broadcast encryption (default)
5. Get Remote device name
Name:
BT_GEN_FID_GET_REMOTE_NAME_REQ
functionality:
Retrieve User-Friendly name of remote Bluetooth device
param 1:
type:
bdaddr
name:
meaning:
the Bluetooth device address of remote
range:
N/A
remote
6. Set BT module name
Name:
BT_GEN_FID_SET_LOCAL_NAME_REQ
functionality:
Set the User-Friendly name for local Bluetooth device
param 1:
type:
u16
name:
meaning:
The length of User-Friendly name
range:
0x01~0x1F
len
param 2:
type:
str
name:
meaning:
The User-Friendly name encoded in UTF-8
range:
N/A
name
7. Read BT Module name
Name:
BT_GEN_FID_READ_LOCAL_NAME_REQ
functionality:
Issue this command to read local device friendly name. the result will be returned by the
confirmation of BT_GEN_FID_READ_LOCAL_NAME_CFM.
remark:
N/A
8. Pairing with Remote device
Name:
BT_GEN_FID_PAIRING_DEVICE_REQ
functionality:
Issue this command to authentication with remote device, when this command is issued
local will init a authentication process with remote device.
NOTE: This command can not be sent when there is a service connection between local
and remote device.
param 1:
type:
bdaddr
name:
meaning:
The Bluetooth device address of remote
range:
N/A
remote
9. Delete paired Remote device
Name:
BT_GEN_FID_DEL_PAIR_DEV_REQ
functionality:
Delete the paired device information according its device id.
param 1:
type:
u8
name:
meaning:
The paired device id.
range:
0x00~0x02
pairId
10. Get paired device list
Name:
BT_GEN_FID_GET_PAIR_DEV_LIST_REQ
functionality:
Get all paired device list.
11. Initiate Service connection
Name:
BT_GEN_FID_SERVICE_CON_REQ
functionality:
Setup a Bluetooth profile level connection
param 1:
type:
bdaddr
name:
meaning:
The Bluetooth device address to be connected
range:
N/A
remote
param 2:
type:
u8
meaning:
The service to be connected
range:
0x00~0x02, 0x04~0x05
0x00: SPP
0x05:PBAP
0x01: HFP
name:
0x02: AVP
service
0x04:OPPS
param 3:
type:
u8
name:
meaning:
The extended info the target service
range:
0x00~0xFF
extend
As for SPP service, it is the instance id;
As for other services, it is reserved and should be always zero.
12. Release Service connection
Name:
BT_GEN_FID_SERVICE_DISCON_REQ
functionality:
Release an existing profile level connection
param 1:
type:
u8
meaning:
The service to be released
range:
0x00~0x02, 0x05
0x00: SPP
0x01: HFP
name:
0x02: AVP
service
0x05: PBAP
param 2:
type:
u8
name:
meaning:
The extended info.
range:
0x00~0x01 (default is 0)
extend
As for SPP service, it is the instance id; As for AVP, it's the device id.
13. Get Link quality with Remote device
Name:
BT_GEN_FID_GET_LINK_QUALITY_REQ
functionality:
Retrieve link quality of current link
param 1:
type:
bdaddr
name:
meaning:
The Bluetooth device address of remote
range:
N/A
remote
14. Get Attribute of Remote device
Name:
BT_GEN_FID_SEARCH_ATTRIBUTE_REQ
functionality:
Search the attributes for services that supported by Remote device
param 1:
type:
bdaddr
name:
meaning:
The Bluetooth device address of remote
range:
N/A
remote
param 2:
type:
u8
name:
meaning:
The timeout of service search in seconds
range:
0x05~0x3C
timeout
15. Enter Test Mode
Name:
BT_GEN_FID_TEST_MODE_REQ
functionality:
Enable local device under test mode
remark:
Request to place the local module into Device Under Test mode. The module
automatically becomes discoverable, connectable and security is disabled before entering
DUT mode. It is intended that this command be used when connecting the module to a
Bluetooth Tester (e.g. Rhode & Schwartz CMU200). To return to normal operation, the
module should be reset. This message contains no parameters.
16. Enter DFU Mode
Name:
BT_GEN_FID_ENTER_DFU_REQ
functionality:
Make the BT Module to enter Device Firmware Upgrade mode
remark:
As soon as this message is processed, Bluetooth module will be rebooted automatically
and ready for firmware maintenance procedures.
There is no parameter for this message.
17. Audio transfer
Name:
BT_HFP_FID_AUDIO_TRANSFER_REQ
functionality:
By sending this command host can transfer SCO audio out between BT module and
remote connected AG device.
param 1:
type:
u8
meaning:
Which side should output the SCO audio
range:
0x00~0x01
0x00 - BT module side
name:
dir
0x01 - AG side
18. Place an outgoing call by number
Name:
BT_HFP_FID_DIAL_REQ
functionality:
Send a dial request to the remote AG device.
Note that the num parameter is limited to 32 bytes in length.
param 1:
type:
u16
name:
meaning:
The length of the dialing number.
range:
0x0000~0x0020
len
param 2:
type:
str
name:
meaning:
Dialing call number
range:
N/A
num
19. Place an outgoing call to last number
Name:
BT_HFP_FID_LAST_DIAL_REQ
functionality:
Send a last dial request to the remote device.
20. Memory dial
Name:
BT_HFP_FID_MEM_DIAL_REQ
functionality:
Send a memory dial request to the remote device.
param 1:
type:
u16
name:
meaning:
The length of the dialling number.
range:
0x0000~0x0020
len
NA
param 2:
type:
str
name:
meaning:
Dialling call number
range:
N/A
num
21. Accept/Reject incoming call
Name:
BT_HFP_FID_CALL_PROCESS_REQ
functionality:
This command is used to accept/reject incoming calls.
param 1:
type:
u8
meaning:
The action for the incoming call
range:
0x00~0x01
0x00 reject the incoming call
name:
action
0x01 - accept the incoming call
22. End ongoing call
Name:
BT_HFP_FID_TERMINATE_CALL_REQ
functionality:
Issue this command to terminate the ongoing call of the remote connected device.
23. Get current call information
Name:
BT_HFP_FID_GET_CURRENT_CALL_LIST_REQ
functionality:
Issue this command to get current call detail information of connected remote device.
24. Voice Recognition
Name:
BT_HFP_FID_VOICE_RECOGNIZE_REQ
functionality:
Issue this command BT Module can activate/deactivate voice recognize in Remote
device.
param 1:
type:
u8
name:
meaning:
Enable/disable the function of voice recognize function.
range:
0x00~0x01
0x00 deactivate (default)
operation
0x01 activate
25. Transmit DTMF code
Name:
BT_HFP_FID_DTMF_CODE_REQ
functionality:
Transmit a DTMF code to the remote device. DTMF codes other than those specified
below will be rejected as per the Bluetooth specification.
param 1:
type:
u8
name:
meaning:
DTMF code
range:
0x30 - 0x39, 'A' - 'D', '#', '*'
code
0x00 means no error, other values please refer to corresponding spec.
26. 3-way call control
Name:
BT_HFP_FID_CALL_HOLD_REQ
functionality:
Issue this command to send call held command to connected remote device.
param 1:
type:
u8
name:
meaning:
The action of call hold command
range:
0x00 - 0x04
action
0x00
0x01
0x02
0x03
0x04
Release all hold call and reject the waiting calls
Release active call and accept the waiting calls
Put active call on hold and accept other waiting/hold calls
Adds a held call to the conversation
Connects the two calls and disconnects the subscriber from both calls
param 2:
type:
u8
name:
meaning:
The index of the speciated call
range:
0x00 - 0x02
index
[action = 0x01]
0x00 Release all active calls
0x01- 0x02 Release the speciated call
[action = 0x02]
0x00 Put all active calls on hold 0x01-0x02 Put all call on hold except the speciated
call.
27. Subscribe number
Name:
BT_HFP_FID_SUBSCRIBER_NUM_REQ
functionality:
Issue this command to query AG subscriber number, if subscriber is available then AG
will return subscriber number by using the indication of subscriber number event, if
multiple subscriber numbers are available then AG will return the result by many use the
event of subscriber number indication.
28. Get network operator of Remote device
Name:
BT_HFP_FID_NETWORK_OPERATOR_REQ
functionality:
Issue this command to get the network operator of remote device. This command not has
any parameters.
29. Start Audio Streaming
Name:
BT_AVP_FID_MEDIA_START_REQ
functionality:
Send a request to start A2DP audio streaming.
param 1:
type:
u8
name:
meaning:
The current used device id
range:
0x00~0x01
device_id
30. Pause Audio Streaming
Name:
functionality:
BT_AVP_FID_MEDIA_PAUSE_REQ
Suspend an ongoing A2DP audio streaming.
param 1:
type:
u8
name:
meaning:
The current used device id
range:
0x00~0x01
device_id
31. Get current Audio Streaming status
Name:
BT_AVP_FID_GET_PLAY_STATUS_REQ
functionality:
This command is used to request the status of the currently playing media at the TG.
param 1:
type:
u8
name:
meaning:
The current used device id
range:
0x00~0x01
device_id
32. Get current media information
Name:
BT_AVP_FID_GET_ELEMENT_ATTRIBUTES_REQ
functionality:
This command is used to request the attributes of the element specified in the parameter.
param 1:
type:
u8
name:
meaning:
The current used device id
range:
0x00~0x01
device_id
param 2:
type:
u8
meaning:
The attributes to be retrieved by setting attribute ID bit mask.
range:
0x00 – 0x7F
Bit0 - Title of the media
Bit2 - Name of the album
Bit4 - Total number of the media
Bit6 - Playing time in millisecond
Get the attribute content by set the
attributes.
name:
attributes
Bit1 - Name of the artist
Bit3 - Number of the media
Bit5 - Genre
Bit7 - Reserved
bit mask to 1, or 0 not. None mask set means get all
33. Phonebook synchronization configure
Name:
functionality:
BT_PBDL_FID_CONFIGURE_REQ
This message used to configure PBDL service before used it. Host must use this interface
to register the wanted service, the service priority and other parameters etc.
param 1:
type:
u8
meaning:
Set the priority of the available service to pull phonebook.
range:
0~1
name:
0 – Priority to use AT+PBDL (default)
srv_ priority
1- Priority to use PBAPC
param 2:
type:
u8
meaning:
The service registered to use PBDL.
range:
0x00 ~ 0xFF (default is 0x00)
bit1: HFP_HF
reserved.
name:
register_srv
bit4: OPP_SERVER
bit5: PBAP_PCE
bit0 and others
param 3:
type:
u8
meaning:
Wanted VCARD version.
range:
0x00, 0x01, 0x02 (default is 0x00)
0x00 – Vcard 2.1
name:
0x01 – Vcard 3.0
vcard_type
0x02 – Vcard Default
param 4:
type:
u8
name:
meaning:
Wanted char set type.
range:
0x00~0x0A
charset_type
0x00: GSM (default)
0x01: ASCII
0x02: UTF-8
0x03: HEX
0x04: IRA
0x05:UCS2
0x0006:PCCP437
0x0007:PCDN
0x0008:8859-1
0x0009:UCS-2
0x000A:UTF8
34. Phonebook synchronization
Name:
BT_PBDL_FID_SYNC_PB_REQ
functionality:
This message used to sync phonebook from remote phone. Firmware will use the available
service as its priority setting by the last configure interface.
param 1:
type:
u8
name:
meaning:
The request device id.
range:
0x00~0x02
devId
param 2:
type:
u8
name:
meaning:
The request phonebook type
range:
0x00~0x01
0x00: Phonebook(SIM, ME) (default)
pbType
0x01:CallHistory(DC, MC, RC)
35. Abort Phonebook synchronization
Name:
BT_PBDL_FID_SYNC_ABORT_REQ
functionality:
This message used to abort the PBDL sync operation.
36. Get phonebook information after synchronization
Name:
BT_PBDL_FID_GET_PB_BY_INDEX_REQ
functionality:
This message used to get the earlier sync phonebook record stored on local flash by its
number.
param 1:
type:
u8
name:
meaning:
The request device id.
range:
0x00~0x02
devId
param 2:
type:
u16
name:
meaning:
The index of the record.
range:
0x0000~0x03E8
index
37. Search phonebook by number after synchronization
Name:
BT_PBDL_FID_SEARCH_PB_BY_NUMBER_REQ
functionality:
This message used to search the phonebook record by number.
param 1:
type:
u8
name:
meaning:
The request device id.
range:
0x00~0x02
devId
param 2:
type:
u16
name:
meaning:
The got number length
range:
0x0000~0x001F
numberLen
param 3:
type:
str
name:
meaning:
The number string.
range:
N/A
number
38. Search phonebook by key word after synchronization
Name:
BT_PBDL_FID_SEARCH_PB_BY_KEY_REQ
functionality:
This message used to search the phonebook record by its key word of name.
param 1:
type:
u8
name:
meaning:
The request device id.
range:
0x00~0x02
devId
param 2:
type:
u24
meaning:
3 bytes UTF-8 Unicode encoding code.
range:
N/A
E.g: A : 0x000041
name:
key
Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or relocate the
receiving antenna; Increase the separation between the equipment and receiver;
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected; Consult the dealer or an experienced radio/TV technician for
help.
In accordance with FCC Part 15C and RSS-210, this module is listed as a Modular
Transmitter device.
1 Changes or modifications not expressly approved by the manufacturer could void
the user’s authority to operate the equipment.
2 The antenna of this transmitter must not be co-located or operating in conjunction
with any other antenna or transmitters within a host device, except in accordance
with FCC multitransmitter product procedures.
FCC Label Instructions
The outside of final products that contains this module device must display a label
referring to the enclosed module. This exterior label can use wording such as the
following: “Contains Transmitter Module FCC ID: [AJDK071]” or “Contains FCC ID:
[AJDK071].” Any similar wording that expresses the same meaning may be used.
If the product is to be sold in Canada, then this exterior label should use wording
such as the following: “Contains Transmitter Module IC: [775E-K071]”
To satisfy FCC RF Exposure requirements for mobile and base station transmission
devices, a separation distance of 20 cm or more should be maintained between the
antenna of this device and persons during operation. To ensure compliance,
operation at closer than this distance is not recommended. The antenna(s) used for
this transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 21
Language                        : zh-CN
Tagged PDF                      : Yes
Author                          : ZhangLi
Creator                         : Microsoft® Word 2010
Create Date                     : 2013:04:25 19:25:51+08:00
Modify Date                     : 2013:04:25 19:25:51+08:00
Producer                        : Microsoft® Word 2010

EXIF Metadata provided by EXIF.tools