Pioneer K084 Speed & Cadence Sensor User Manual 07 User Manual

Pioneer Corporation Speed & Cadence Sensor 07 User Manual

07_User-Manual

ENENFRSpeed & Cadence SensorSGY-CH500BUser’s ManualManuel de l'utilisateurSGY-CS500
2ENTable of ContentsFeatures ................................................................................................................... 2Important Safety Information ................................................................................... 3Before Use (Important) ............................................................................................ 9Product Conguration .............................................................................................12Part Names and Functions .....................................................................................13Installation on Your Bike .........................................................................................14Installing the Cadence Magnet .............................................................................................14Installing the Speed & Cadence Sensor ..............................................................................15Installing the Speed Magnet .................................................................................................16Fixing the Sensor ..................................................................................................................18Installing and Removing the Battery ......................................................................19Troubleshooting ......................................................................................................21Specications ........................................................................................................ 22FeaturesTrip Data AcquisitionThis device acquires trip data like speed and cadence, and those data are displayed on the cyclocomputer.This product is ANT+™ certied.Visit http://www.thisisant.com/directory/ for a list of compatible products and apps.
3ENImportant Safety InformationPioneer Speed & Cadence Sensor is not a medical device.Important Information About This DeviceThis device helps provide feedback about cycling. It is intended solely for recreational purposes. THE LIMITED WARRANTY PROVIDED WITH THIS DEVICE CONSTITUTES THE EXCLUSIVE WARRANTIES FOR THE PRODUCT AND THE USER’S EXCLUSIVE REMEDIES. TO THE MAXIMUM EXTENT ALLOWED BY APPLICABLE LAW, ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED, OR STATUTORY, INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED. IN NO EVENT WILL PIONEER, ITS AFFILIATES, OR THEIR RESPECTIVE EMPLOYEES, DIRECTORS, OR OFFICERS, BE LIABLE FOR ANY INDIRECT, INCIDENTAL, CONSEQUENTIAL, SPECIAL, PUNITIVE OR EXEMPLARY DAMAGES IN CONNECTION WITH THIS DEVICE, REGARDLESS OF THE THEORY OF LIABILITY AND EVEN IF SUCH DAMAGES ARE FORESEEABLE. BECAUSE SOME STATES OR JURISDICTIONS MAY NOT ALLOW LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, OR LIMITATIONS ON OR EXCLUSIONS OF CONSEQUENTIAL OR INCIDENTAL DAMAGES, SOME OF THE ABOVE LIMITATIONS MAY NOT APPLY TO A USER DEPENDING ON HER, HIS, OR ITS STATE OF RESIDENCE.
4ENImportant Safety Information WARNINGBEFORE BEGINNING OR • MODIFYING ANY EXERCISE ACTIVITY, ALWAYS CONSULT YOUR PHYSICIAN FIRST. IF YOU ARE USING A PACEMAKER OR ANY OTHER IMPLANTED DEVICE, CONSULT YOUR PHYSICIAN BEFORE USING A HEART RATE SENSOR.THIS PRODUCT IS NOT A • MEDICAL DEVICE, AND COULD EXPERIENCE INTERFERENCE FROM EXTERNAL ELECTRICAL SOURCES. WARNINGFollow these guidelines as well to ensure safe Cycling:Always use your best judgement, • and ride in a safe manner. Do not become distracted by this device while riding, and always be fully aware of your surroundings.Secure your bicycle in a safe place • before replacing batteries as the bicycle could fall causing injury.Upon replacing the battery, install • the the battery cover securely to ensure water resistance and prevent potential injury if the cover falls off.Do not leave small parts such as • screws or the battery in an area that infants and small children can reach to prevent accidental swallowing. If you think this may have happened, call 911 for a medical emergency.Before riding, check that the Speed • & Cadence sensor does not contact with a crank or spoke.
5ENImportant Safety InformationBefore riding, check that the sensor • and magnets are installed securely. Also check that the speed detector arm’s screw is not loose, there are no cracks in the band, and the band’s xing tape is not coming off.Do not leave this device in places • that are exposed to direct sunlight, high temperature, high humidity, or a lot of dust as it may cause the device to malfunction.Never dismantle, refurbish, or repair • this device or any attached parts as it could cause electrical shock or the device to malfunction.Do not use this device if any unusual • conditions exist such as penetration by a foreign object, water submersion, smoke is detected, or an unusual odor is detected. Stop using this device immediately and have it repaired.Do not subject this device to • extreme shock by riding on rough roads. Doing so could damage this device or cause it to malfunction.This device communicates using ANT+ • radio communication. Do not use in areas that forbid the use of electronic devices such as hospitals or airplanes as unintended interference from this device could cause serious accidents. CAUTIONDo not wipe this device with • detergents, chemical duster, or volatile compounds such as benzine or thinner as they may cause the device to malfunction.Thoroughly remove any excess • bicycle lubricants or cleaners from this device as it could cause damage.Avoid overly violent impacts on • this device as it may cause it to malfunction.Do not wash this device with a high • pressure water sprayer as water may penetrate into this device causing it to malfunction.Do not touch or deform the battery • contacts. This could cause a faulty connection or short circuit.
6ENImportant Safety Information WARNINGBatteries (batteries installed) must not be exposed to excessive heat such as sunshine, re or the like.“Perchlorate Material - special handling may apply.Seewww.dtsc.ca.gov/hazardouswaste/perchlorate.(Applicable to California, U.S.A.)” WARNINGSTORE SMALL PARTS OUT OF REACH OF CHILDREN AND INFANTS. IF ACCIDENTALLY SWALLOWED, CONTACT A DOCTOR IMMEDIATELY.Radio wave cautionThis unit uses a 2.4 GHz radio wave • frequency, which is a band used by other wireless systems (microwave ovens and cordless phones, etc.).In the event noise appears on your television image, there is the possibility this unit (including products supported by this unit) are causing signal interference with the antenna input connector of your television, video, satellite tuner, etc. In this event, increase the distance between the antenna input connector and this unit (including products supported by this unit).
7ENImportant Safety Information[For American Users]IMPORTANT NOTICEKEEP WARRANTY CARD IN A SAFE PLACE FOR FUTURE REFERENCE.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.WARNING: This product contains chemicals known to the State of California and other governmental entities to cause cancer and birth defects or other reproductive harm.Wash hands after handling.The grantee is not responsible for any changes or modifications not expresslyapproved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment.This equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmfulinterference to radio communications. However, there is no guarantee that interferencewill not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turningthe equipment off and on, the user is encouraged to try to correct the interferenceby one or more of the following measures:—Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver.—Connect the equipment into an outlet on a circuit different from that to whichthe receiver is connected.—Consult the dealer or an experienced radio/TV technician for help.
8ENImportant Safety Information[For Canadian Users]This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accep ter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that are deemed to comply without testing of specic absorption ratio (SAR).Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée conforme sans évaluation du débit d’absorption spécique (DAS).The ANT+ antenna cannot be removed (or replaced) by user.L'antenne ANT+ ne peut pas être supprimé (ou remplacé) par l'utilisateur.Operating EnvironmentOperating environment temperature and humidity:-10 °C to +60 °C (+14 °F to +140 °F); less than 85 %RHDo not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong articial light)
9ENBefore Use (Important)Safety Precautions DANGERAbout this DeviceDo not throw this device, strike it • with a hammer or other object, or pierce this device in any way.Do not use or leave this device in • places where it will be exposed to extremely high temperatures, such as near a stove or re.Always keep this device out of the • reach of infants and small children. WARNINGAbout this DeviceDo not use this device if it emits an • unusual odor, heats up, changes color or shape, or if any other abnormalities occur during use.Do not place this device in a • microwave oven or expose it to high pressure, since the device may overheat, rupture, or ignite.Keep the lithium battery out of the • reach of children. Should the battery be swallowed, immediately consult a doctor.
10ENBefore Use (Important) CAUTIONDo not recharge, disassemble, heat • or dispose of the battery in re.Use a CR2032 (3 V) lithium battery • only. Never use other types of batteries with this unit.Do not handle the battery with • metalic tools.Do not store the battery with metallic • materials.When disposing of used batteries, • please comply with governmental regulations or environmental public institutions rules that apply in your country or area.Always check carefully that you are • loading battery with its (+) and (-) poles facing in the proper directions. CAUTIONAbout Water-resistanceObserve the following precautions in regard to this device’s water-resistant.Do not place the unit in water.• Do not expose the unit to a large • amount of water.Do not expose to rain for long • periods of time.Do not pour or place in warm • water or water containing soap or detergent.Do not use at or near the beach.• This could cause rust. If exposed to seawater, thoroughly wipe off the moisture immediately with a dry cloth.If the rubber packing becomes • soiled, wipe it clean with a dry, clean cloth.Do not open the battery cover • in humid environments in which this device could get exposed to water.
11ENBefore Use (Important)If this device is exposed to a large • amount of water or moisture, immediately wipe it down with a dry cloth.Only open or close the battery cover after having completely wiped off any moisture. Be sure your hands are completely dry and you are in an environment where the unit will not get exposed to moisture again.Over exposure or submersion in • water may require servicing.This device is water resistant to 6 m.Malfunctions due to water damage caused by improper use are not covered by the product warranty, even if they occur within the warranty period.Depending on conditions of use, • the water-resistant features are not necessarily guaranteed even during the warranty period.
12ENProduct CongurationThis product contains the following parts.Speed & Cadence sensor • (main unit, mounting holder)Cadence magnet • Speed magnet • (magnet, holder, sheet)Sensor mounting band• Fixing tape for the sensor • mounting bandUser’s Manual (this manual)• Warranty Card•
13ENPart Names and FunctionsFront View Cadence sensorDetects the cadence magnet installed on the crank. LED for cadence magnet detectionBlinks green when it detects the magnet just after the sensor is activated. LED for speed magnet detectionBlinks red when it detects the magnet just after the sensor is activated. Speed detector armAdjust the angle by turning the hex screw (2 mm) ( ).Back View Speed sensorDetects the speed magnet installed on the spoke. Hex screw for adjusting the angle of the arm Battery cover Mounting holder
14ENInstallation on Your BikeMount the Speed & Cadence sensor, cadence magnet, and speed magnet on your bike.Pairing with the cyclocomputer may not be possible due to the inuence of the ●2.4 GHz frequency band. If pairing fails, try again someplace where there is no interference from microwaves, radio waves, or wireless equipment.Do not use magnets other than the enclosed ones. ●Installing the Cadence Magnet1. Remove the pedal from the crank.2. Install the cadence magnet to the crank.Install it so the magnet part is facing to the chain stay side.Chain stayMagnetThe magnet can be installed to a • crank that is from about 90 mm up to 100 mm in circumference.Be careful not to get injured when • installing the cadence magnet.After installing the cadence magnet, • conrm that it is not cracked. If it is cracked, do not use it.
15ENInstallation on Your BikeInstalling the Speed & Cadence Sensor1. Temporarily mount the Speed & Cadence sensor on the chain stay.Hook the band on the hook located on the back side of the sensor, and then put the band in the groove on the front side to temporarily mount the sensor on the chain stay.The sensor can be installed to a • chain stay that is from about 100 mm up to 120 mm in circumference.The sensor cannot be installed • securely on some chain stays’ shapes. Conrm the chain stay’s shape when installing it.Do not pull the band too strongly. • Doing so may break the band.2. Adjust the location of the Speed & Cadence sensor.Adjust the sensor by tilting it so the center of the cadence magnet passes about 3 mm from the sensor part (concave part) of the Speed & Cadence sensor when the crank is rotated.3 mmWhen the sensor detects the cadence magnet as the cranks are rotated, the LED blinks green every time it is detected, up to 10 times.
16ENInstallation on Your BikeAfter blinking 10 times, the LED will • not light even though the sensor detects the magnet. The LED starts blinking again if you re-install the sensor’s battery or wait at least 20 minutes after the last time the sensor detects the magnet.Installing the Speed Magnet1. Loosen the screw of the speed magnet and remove the magnet part.2. Install the speed magnet to the spoke of the back wheel.
17ENInstallation on Your BikeThe magnet can be installed on a • spoke that is from about 1.5 mm up to 2.5 mm in diameter.The magnet cannot be installed securely • on some spokes’ shapes. Conrm the spoke’s shape when installing it.Installing the magnet may damage • the spoke. Protect the spoke if you do not want to damage it.Be careful not to lose the sheet and • so on, when installing the magnet.After installing the magnet, check • that its screw has not been screwed in at an angle.3. Adjust the angle of the speed detector arm.Adjust the angle of the arm by turning the hex screw so the center of the speed magnet passes about 3 mm from the sensor part (concave part) of the arm when the wheel is rotated.3 mmWhen the sensor detects the speed magnet as the wheel rotates, the LED blinks red up to 10 times each time it is detected.Install the sensor so the arm does • not interfere with the spokes.Do not move the arm beyond its • range of motion (60°).60°After blinking 10 times, the LED will • not light even though the sensor detects the magnet. The LED starts blinking again if you re-install the sensor’s battery or wait at least 20 minutes after the last time the sensor detects the magnet.Speed is not detected until you • tighten the angle adjustment screw of the arm.
18ENInstallation on Your BikeFixing the SensorAfter installing the Speed & Cadence sensor, cadence magnet, and speed magnet, pair the sensor with the Cyclocomputer SGX-CA500 or other cyclocomputer, and conrm that the cadence is displayed with the rotation of the crank, and the speed is displayed with the rotation of the wheel. Refer to the Quick Start Guide of the Cyclocomputer SGX-CA500 or your cyclocomputer’s owner manual for sensor pairing.After conrming that the information from the Speed & Cadence sensor is displayed correctly, x the band with the xing tape for the sensor’s band.After xing the Speed & Cadence sensor, install the pedal to the crank.Be sure to use the xing tape. If • you do not use the xing tape, the sensor’s band may slip off and the sensor may fall off during a ride.Do not re-use the xing tape. The • used xing tape may come off during a ride because its adhesion has decreased.Securely x the Speed & Cadence • sensor to the chain stay so it does not fall towards the crank or spokes while riding.Before riding, check that the sensor • and magnets are installed securely. Also check that the speed detector arm’s screw is not loose, there are no cracks in the band, and the band’s xing tape is not coming off.When the sensor or magnets • become soiled with mud or anything else, wipe them off.
19EN1. Remove the battery cover of the Speed & Cadence sensor.Turn the cover counterclockwise with a tool such as a coin or screwdriver, until it stops turning.2. Remove the old battery.Installing and Removing the BatteryThe battery is pre-installed to this product. If the battery is almost empty (see page 21), replace the battery with new one.3. Install the new battery (CR2032) and close the battery cover.Insert the battery with its (-) side facing up and wait more than 3 seconds to remove it. Then insert it with its (+) side facing up. Doing this resets the sensor so it operates reliably.Then turn the battery cover clockwise until it stops and is closed tightly.Be careful not to lose the rubber • gaskets when removing the battery cover.Rubber gaskets
20ENInstalling and Removing the BatteryBe careful not to drop or lose the • battery when installing it.Do not use batteries other than CR2032.Install the cover rmly to ensure • water resistant performance.If a mud or water is on the battery • cover, wipe it off with a dry cloth before removing the cover. Do not touch the cover with wet hands.When disposing of used batteries, • please comply with governmental regulations or environmental public institutions rules that apply in your country or area.Keep coin batteries out of reach of • children.
21ENTroubleshootingIf you have problems with your device, check the following items.If a solution to your problem cannot be found here, contact your dealer.Speed & Cadence sensor information is not displayed on the cyclocomputer. / ■I cannot pair the sensor with the cyclocomputer.Cause SolutionSensitivity of the sensor has become low due to dirt such as mud on the sensor or magnets.Wipe off dirt from the sensor or magnets.The battery is almost empty. Replace the battery with a new one (see page 19). (+) or (-) side of the battery is installed in the opposite side.Install the battery in the proper side (see page 19).The battery is not installed correctly. Install the battery again (see page 19).The sensor is not mounted correctly. Conrm the position of the sensor and magnets, and the distance between them (see page 15, 16).Pairing between the sensor and the cyclocomputer has not been done.Check if the sensor is paired with the cyclocomputer. If not, pair them. Refer to the Quick Start Guide of the Cyclocomputer SGX-CA500 or your cyclocomputer’s owner manual for sensor pairing.Sensor has not been reset. Install the battery with its (+) side down and wait more than 3 seconds, then remove the battery. The sensor is reset in this way.Connection is not possible due to the inuence of the 2.4 GHz frequency band. Try pairing again someplace where there is no interference from microwaves, Wi-Fi such as a wireless LAN, or other wireless ANT equipment.Speed is not displayed. ■Cause SolutionThe screw of the speed detector arm is loose.Tighten the screw of the speed detector arm so it is not loose. Speed is not detected if the screw is loose.
22ENSpecicationsWeight: Sensor:About 24 gDimensions: Sensor:36 mm(W) x 42 mm (H) x 16.5 mm(D)Water resistant: This device is water resistant to 6 m.Communications method (sensors): ANT+ wirelessBattery: CR2032Operation temperature: -10 to 60°CEstimated usable period: About 3 years (at one hour per day of use)ANT+ is a Wireless Personal Network protocol with very low power • requirements using 2.4GHz frequency band.For more information, visit http://www.thisisant.com/Specications and design are subject to change without notice.• Illustrations used in this manual may be different from actual appearance.•
©2014 PIONEER CORPORATION.All rights reserved.5615N4630006R00http://www.pioneerelectronics.comhttp://www.pioneerelectronics.caVisit www.pioneer.eu to register your product.Visitez www.pioneer.eu pour enregistrer votre appareil.PIONEER CORPORATION1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, JAPANPIONEER ELECTRONICS (USA) INC.P.O. Box 1540, Long Beach, California, 90801-1540, U.S.A.TEL: (800) 421-1404PIONEER ELECTRONICS OF CANADA INC.340 Ferrier Street, Unit 2, Markham, Ontario, L3R 2Z5, CanadaTEL: 1-877-283-5901TEL: 905-479-4411

Navigation menu