Pioneer Audio Video Stereo Receiver Vsx D3S Users Manual ARB7050C

VSX-D3S to the manual 027eb5eb-e67f-45d9-81ba-df907198bf9b

2015-01-26

: Pioneer Pioneer-Audio-Video-Stereo-Receiver-Vsx-D3S-Users-Manual-334911 pioneer-audio-video-stereo-receiver-vsx-d3s-users-manual-334911 pioneer pdf

Open the PDF directly: View PDF .
Page Count: 40

Operating

Instructions

AUDIO/VIDEO STEREO RECEIVER

N∫m¿Û≤∫

DEMO MODE

¶The demonstration mode is activated by turning on the

power switch while holding down the RETURN button

(from power standby condition). The demonstration will

appear on the display.

¶Press any button to cancel the demonstration. Activating

the demonstration mode causes memory contents to return

to their original default condition, except the tuner.

U.S. and Canadian models NTSC

Multi-voltage model NTSC/PAL

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO

NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

RETURN function

This function returns the unit to its initial settings with the

tuner ready to receive a broadcast. This is helpful during

troubleshooting or when no sound is output. For details,

refer to page 13.

RESET function

Set the MASTER VOLUME to minimum before pressing the

RESET button.

Use this function when normal operation is not possible due

to external influences such as static electricity or lightning, or

when operations are not functioning even when the operation

switches are pressed. Press the RESET button to return to

normal operating conditions.

Thank you for buying this Pioneer product.

Please read through these operating instructions so you will

know how to operate your model properly. After you have

finished reading the instructions, put them away in a safe place

for future reference.

In some countries or regions, the shape of the power plug and

power outlet may sometimes differ from that shown in the

explanatory drawings. However, the method of connecting and

operating the unit is the same.

IMPORTANT NOTICE

[For U.S. and Canadian models]

The serial number for this equipment is located on the rear

panel. Please write this serial number on your enclosed warranty

card and keep it in a secure area. This is for your security.

[For Canadian model]

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE

THIS (POLARIZED) PLUG WITH AN EXTENSION CORD,

RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE

FULLY INSERTED TO PREVENT BLADE EXPOSURE.

ATTENTION: POUR PREVENIR LES CHOCS ELECTRIQUES

NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN

PROLONGATEUR, UNE PRISE DE COURANT OU UNE AUTRE

SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE

INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A

DECOUVERT.

AUDIO/VIDEO STEREO RECEIVER

N∫m¿Û≤∫

POWER

STANDBY/ON

RETURN

SPEAKERS

TAPE 2

MONITOR PHONO TUNER

LD CD

SURROUND MODE

MASTER VOLUME

SUPER BASS

TREBLEBASS

MEMORY SELECT

FM/AM MPX MODE

GUI

MODE

AUDIOLR

VIDEO

PHONES

FLAT MAX

VIDEO

INPUT

TV/SAT

VIDEO

VCR 1 VCR 2 TAPE 1

AC-3

STANDBY

RESET

INPUT

ATT

GUI

ENTER

MIN MAX

MULTI-JOG

DSP OFF

TUNING MODE

SLEEP DIRECT

DOLBY SURROUND

Intelligent System Control

DOLBY

PRO-LOGIC

DSP MODE

SUPER

BASS

+–+–

AC-3 PRO • LOGIC

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

The lightning flash with arrowhead, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated "dangerous voltage" within the

product's enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

READ INSTRUCTIONS

—

All the safety and operating

instructions should be read before the appliance is

operated.

RETAIN INSTRUCTIONS

—

The safety and operating

instructions should be retained for future reference.

HEED WARNING

—

All warnings on the appliance and

in the operating instructions should be adhered to.

FOLLOW INSTRUCTIONS

—

All operating and use

instructions should be followed.

WATER AND MOISTURE

—

The appliance should not

be used near water – for example, near a bathtub,

washbowl, kitchen sink, laundry tub, in a wet

basement, or near a swimming pool, etc.

LOCATION

—

The appliance should be installed in a

stable location.

WALL OR CEILING MOUNTING — The appliance

should not be mounted to a wall or ceiling.

VENTILATION

—

The appliance should be situated so

that its location or position does not interfere with its

proper ventilation. For example, the appliance should

not be situated on a bed, sofa, rug, or similar surface

that may block the ventilation openings; or, placed in

a built-in installation, such as a bookcase or cabinet

that may impede the flow of air through the

ventilation openings.

HEAT

—

The appliance should be situated away from

heat sources such as radiators, heat registers, stoves,

or other appliances (including amplifiers) that produce

heat.

POWER SOURCES

—

The appliance should be

connected to a power supply only of the type

described in the operating instructions or as marked

on the appliance.

POWER-CORD PROTECTION

—

Power-supply cords

should be routed so that they are not likely to be

walked on or pinched by items placed upon or

against them. Pay particular attention to cords at

plugs, convenience receptacles, and the point where

they exit from the appliance.

POLARIZATION

—

If your purchased product is

provided with a polarized power plug, please read the

following instructions. This product is equipped with

a polarized alternating current line plug (a plug having

one blade wider than the other). This plug will fit into

the power outlet only one way. This is a safety

feature. If you are unable to insert the plug fully into

the outlet, try reversing the plug. If the plug should

still fail to fit, contact your electrician to replace your

obsolete outlet. Do not defeat the safety purpose of

the polarized plug.

CLEANING

—

The appliance should be cleaned only

with a polishing cloth or a soft dry cloth. Never clean

with furniture wax, benzine, insecticides or other

volatile liquids since they may corrode the cabinet.

POWER LINES

—

An outdoor antenna should be

located away from power lines.

NONUSE PERIODS

—

The power cord of the appliance

should be unplugged from the outlet when left

unused for a long period of time.

OBJECT AND LIQUID ENTRY

—

Care should be taken

so that objects do not fall and liquids are not spilled

into the enclosure through openings.

DAMAGE REQUIRING SERVICE

—

The appliance

should be serviced by a Pioneer authorized service

center or qualified service personnel when:

The power–supply cord or the plug has been

damaged.

• Objects have fallen, or liquid has been spilled into the

appliance.

• The appliance has been exposed to rain.

• The appliance does not appear to operate normally or

exhibits a marked change in performance.

• The appliance has been dropped or the enclosure

damaged.

SERVICING

—

The user should not attempt to service

the appliance beyond that described in the operating

instructions. All other servicing should be referred to

qualified service personnel.

OUTDOOR ANTENNA GROUNDING

—

If an outside

antenna is connected to the antenna terminal, be

sure the antenna system is grounded so as to

provide some protection against voltage surges and

built-up static charges.

In the U.S.A. section 810 of the National Electrical

Code, ANSI/NFPA 70, provides information with

respect to proper grounding of the mast and

supporting structure, grounding of the lead-in wire to

an antenna discharge unit, size of grounding

conductors, location of antenna discharge unit,

connection to grounding electrodes, and

requirements for the grounding electrode. See Fig. A.

CART

—

An appliance and cart combination should be

moved with care. Quick stops, excessive force, and

uneven surfaces may cause the appliance and cart

combination to overturn.

NEC — NATIONAL ELECTRIC CODE

GROUND

CLAMP

SAFETY INSTRUCTIONS

GROUND

CLAMP

GROUND

CLAMP

GROUND

CLAMP

GROUND

CLAMP

•

GROUND

CLAMP

GROUND

CLAMP

ANTENNA

LEAD-IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810

–

20)

GROUNDING CONDUCTORS

(NEC SECTION 810

–

21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

GROUND

CLAMP

ELECTRIC

SERVICE

EQUIPMENT

FIG. A

GROUND

CLAMP

GROUND

CLAMP

GROUND

CLAMP

Note to CATV system installer

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper

grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the

point of cable entry as practical.

Information to User

Alteration or modifications carried out without appropriate authorization may invalidate the user’s right to operate the equipment.

INSPECTION CHECKLIST

The Pioneer Receiver is packaged with the following

items:

If any of these items were not included in the package, contact

the dealer where you purchased the product from to obtain the

missing items or a complete replacement.

CONTENTS

BEFORE OPERATING

INSPECTION CHECKLIST ............................................................ 3

INSTALLATION ............................................................................ 4

SETTING THE SWITCHES

FOR THE MULTI-VOLTAGE MODEL ONLY ...................... 4

INSTALLATION PRECAUTIONS ............................................. 5

CONNECTIONS

ANTENNA CONNECTIONS .................................................... 6

AUDIO SYSTEM CONNECTIONS .......................................... 7

VIDEO SYSTEM CONNECTIONS ........................................... 8

SPEAKER SYSTEM CONNECTIONS ...................................... 9

IR REPEATER CONNECTION ................................................ 10

PANEL FACILITIES

REAR PANEL FACILITES............................................................ 11

FRONT PANEL FACILITIES ........................................................ 13

DISPLAY SECTION ............................................................... 15

OPERATIONS

OPERATING THE TUNER .......................................................... 16

TUNING INTO STATIONS .................................................... 16

FREQUENCY PRESETTING .................................................. 16

LISTENING TO BROADCASTS USING PRESET TUNING ... 16

RECEIVING FM SIMULCAST TV PROGRAMS ..................... 17

OPERATING THE AUDIO/VIDEO COMPONENTS..................... 17

PLAYBACK ............................................................................ 17

RECORDING WITH A CASSETTE DECK.................................... 18

RECORDING WITH TAPE 1 ................................................... 18

RECORDING WITH TAPE 2 ................................................... 18

USING VCR 1, VCR 2 FOR AUDIO RECORDING .................. 18

COPYING TAPES .................................................................. 18

VIDEO RECORDING ................................................................... 19

SURROUND EFFECT.................................................................. 19

REMOTE CONTROL OPERATION

PUTTING BATTERIES INTO THE REMOTE CONTROL UNIT

... 20

REMOTE CONTROL RANGE ................................................ 20

RECEIVER CONTROL BUTTONS .......................................... 21

OPERATING OTHER COMPONENTS ................................... 21

OPERATING USING GUI

RECEIVER CONTROL BUTTONS .......................................... 24

OPERATING THE TUNER .......................................................... 25

MANUAL/AUTO TUNING ..................................................... 25

PRESET TUNING .................................................................. 25

OPERATING OTHER COMPONENTS ........................................ 26

COPY OPERATION ..................................................................... 28

USING THE VIDEO SIGNAL SELECTOR ................................... 28

SOUND EDIT OPERATION ........................................................ 29

SETTING THE SPEAKER MODE ........................................... 29

LEVEL AND BALANCE ADJUSTMENT ................................ 30

REMOTE SET UP........................................................................ 31

ONE TOUCH OPERATION SET UP............................................ 33

TROUBLESHOOTING ................................................................ 34

APPENDICES

APPENDIX A: SPECIFICATIONS ................................................ 36

APPENDIX B: SURROUND EFFECT .......................................... 37

APPENDIX C: DOLBY AC-3 SURROUND .................................. 38

Operating Instructions

Main-Repeater

AM Loop Antenna

FM T-type antenna

Remote control unit

Dry cell batteries

(size “AA” IEC R6P) x 2

Mini-Repeater

Warranty Card

(Not supplied in multi-voltage model.)

INSTALLATION

SETTING THE SWITCHES FOR THE MULTI-VOLTAGE MODEL ONLY

TWO VOLTAGE SELECTOR SWITCHES

(Not available on U.S. and Canadian models)

Only multi-voltage models are provided with these

switches. U.S. and Canadian models are not provided

with these switches. Mains voltages in Saudi Arabia are

127 V and 220 V only. Never use this model with the 110

V setting in Saudi Arabia.

The line voltage selector switches are on the rear panel. Before

your model is shipped from the factory, these switches are set

to the power requirements of the destination. Check that they

are set properly before plugging the power cord into the

household wall socket. If the voltage is not properly set or if you

move to an area where the voltage requirements differ, adjust

the selector switches as follows.

1. Use a medium-size screwdriver.

2. First, insert the screwdriver in the groove of the voltage

selector at the right, and adjust so that the tip of the groove

points to the voltage value of your area.

3. Next, insert the screwdriver in the groove of the voltage

selector at the left and adjust until the voltage is the same as

at the right.

PAL/NTSC SWITCH

(Not available on U.S. and Canadian models)

This unit uses the TV screen to operate the system. Set the rear

panel PAL/NTSC switch to match your TV’s color system. The

screen will be unclear if the color system does not match.

CHANNEL STEP/FM DE-EMPHASIS SWITCH

(Not available on U.S. and Canadian models)

The unit has been factory preset to the channel allocation and

de-emphasis value for the area in which it is to be sold. If these

values are set incorrectly, the tuned in frequency may be wrong,

or sound may be distorted, resulting in an inability to reproduce

reception signals at their proper sound quality. For this reason,

be sure to confirm that the values are set correctly before first

using the unit.

(FM 100 kHz/75 µs, AM 10 kHz) position:

Set to this position for areas with an FM reception step of 100

kHz, de-emphasis 75 µs and AM 10 kHz.

(FM 50 kHz/50 µs, AM 9 kHz) position:

Set to this position, for areas with an FM reception step of 50

kHz, de-emphasis 50 µs and AM 9 kHz.

NOTE:

When unsure about the channel allocation and de-emphasis

values for your area, consult your dealer for correct information.

Medium-size screwdriver

TWO VOLTAGE SELECTORS

110V

120∼127V

220V

240V

220V

110V 120-127V

240V

PAL NTSC

FM 50kHz

/50μS

AM 9kHz

CHANNEL

/FM DE-

100kHz

/75μS

10kHz

STEP

EMPHASIS

INSTALLATION

INSTALLATION PRECAUTIONS

INSTALLING THE RECEIVER

÷Place the unit on a stable platform next to the television and

stereo system to be used with the unit.

÷When using the unit with a stereo system, your speakers

should be placed away from your television (or TV monitor).

÷Do not place heavy objects such as a television or TV monitor

on top of the unit.

÷Do not place the unit on top of your TV set or TV monitor. Also,

keep the unit away from devices such as cassette decks which

are sensitive to magnetic fields.

If the cassette deck is installed in the A positions as shown in

the drawing below, it may be adversely affected during

playback. If possible, it is better to install it in the B position.

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the plug by

tugging the cord and never touch the power cord when your

hands are wet as this could cause a short circuit or electric

shock. Do not place the unit, a piece of furniture, etc., on the

power cord, or pinch the cord. Never make a knot in the cord or

tie it with other cords. The power cords should be routed such

that they are not likely to be stepped on. A damaged power cord

can cause a fire or give you an electrical shock. Check the power

cord once in a while. When you find it damaged, ask your

nearest PIONEER authorized service center or your dealer for a

replacement.

SURROUND SPEAKER INSTALLATION EXAMPLE

To get the best effect out of the surround system, place the

speakers as shown below.

An example for center speaker location

INSTALL THE RECEIVER IN A WELL-VENTILATED

PLACE AWAY FROM HEAT AND HUMIDITY

Do not install the unit in a location subject to direct sunlight, or

near a stove or radiator, etc. This could adversely affect the

cabinet and internal components. Also, avoid installing the unit

in a humid or dusty location. This could result in a malfunction

or accident. Do not install near a cooking stove where the unit

could be affected by smoke, steam, or heat. Avoid placing the

unit on surfaces such as shaggy carpets, beds and sofas which

may block ventilation under the unit and may cause damage.

÷The rear panel vents are designed to disperse heat from the

unit. Be careful that curtains or other items do not block the

vents.

÷ To improve heat dispersion, set the unit so that it is at least

20 cm (8 inches) away from the wall.

At least 20 cm (8 inches)

When using a single

center speaker

When using dual center

speakers

NOTE:

To avoid interference with the picture on a nearby TV set, use

magnetically shielded speaker systems. This is particularly

important for the center speaker since it is usually located

closest to the TV.

Position the left and right channel speakers at equal distances

from the TV set and approximately 1.8 m (6 feet) from each

other.

Position the center speaker above, below, or behind the TV set.

Sound may not appear to coincide with the picture if you

position it next to the TV set.

Rear speakers are best positioned slightly above ear level.

You can set this unit to match the requirements and

specifications of your stereo system’s speakers (whether or

not center speaker(s), rear speakers or a sub-woofer are

used, speaker size, etc.) to assure optimum sound quality.

Before using, perform settings in the SPEAKER MODE (refer

to page 29).

NOTE:

This unit does not feature conventional switching between

NORMAL/ WIDE/PHANTOM center modes.

CENTER SPEAKER

FRONT

REAR

RIGHT

FRONT

SPEAKER

RIGHT

SURROUND

SPEAKER

LEFT

FRONT

SPEAKER

LEFT

SURROUND

SPEAKER

Listening Area

A B

Receiver

CONNECTIONS

ANTENNA CONNECTIONS

NOTE FOR FM ANTENNA:

Stretch the antenna out to its full length and affix it to a wall, etc.

NOTE FOR AM LOOP ANTENNA:

The antenna should be placed at a distance from the receiver,

and should not be allowed to touch metallic objects. Avoid

placing it near CD players, personal computers, television sets

and other devices generating radio frequencies.

Setting Up the AM Antenna

÷Insert the claw on the bottom of the antenna into the

groove in the leg.

÷ Place the antenna on a level surface and rotate it to locate

the orientation that yields the best reception.

÷Use the attachment hole in the leg to screw to a wall or

other location, then insert the claw on the bottom of the

antenna into the groove in the leg (affixing the antenna in

the direction that gives the best reception.)

Twist the wire strands together.

Stretch the antenna out

to its full “T” shape and

affix it to a wall, etc.

Accessory FM T-type antenna

Leg

Lead wire

(1-3/16) 15(9/16)

Unit: mm (in)

FM outdoor antenna

300 Ω feeder

GROUND

coaxial 75 Ω cable F-type plug

Indoor AM wire antenna

(Polyvinyl insulated wire)

Outdoor AM antenna

AM loop antenna

GROUND

7OUTDOOR FM ANTENNA

The main advantage of FM over AM is the quality of the

broadcast signal. In order to benefit fully from the high signal

quality of FM broadcasts, it is recommended that a special-

purpose FM antenna be installed. In weak signal areas, a multi-

element (3-, 5-, or 7-element) antenna should be used.

7GROUNDING

Grounding is recommended if reception of FM programs is

impaired by noise. To ground, connect a thick polyvinyl insulated

wire to the GND terminal and attach the other end to a metal

water pipe or grounding bar or wind it around a copper plate

and bury it.

CAUTION:

Never connect a wire to a gas pipe for grounding since sparks may

ignite the gas.

7EXTERNAL AM ANTENNA

If it is not possible to obtain adequate AM reception even by

changing the orientation of the AM loop antenna, a separate

indoor antenna, or an outdoor antenna should be installed.

INDOOR AM ANTENNA

Use a vinyl insulated wire (5 — 6 m, 17 — 20 feet), and connect

one end to the AM antenna terminal and affix the other end to

the wall or ceiling, as high as possible.

OUTDOOR AM ANTENNA

If reception quality is not improved sufficiently even when an

indoor antenna is used, a vinyl insulated wire should be installed

outside and fixed in place.

NOTE:

Do not detach the AM loop antenna when using an indoor or an

outdoor AM antenna.

Illustration shows Multi-voltage model.

Accessory AM

loop antenna

PHONO

TAPE2

MONI-

TOR

TAPE1

OUT

TO MONITOR TV

VIDEO OUT

CONTROL

OUT

GND

REC

PLAY

REC

OUT

VCR2

VCR1

/SAT

SEE INSTRUCTION MANUAL

MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES LICENSING CORPORATION.

"DOLBY","AC-3", "PRO LOGIC" AND THE DOUBLE-D SYMBOL ARE TRADEMARKS OF

DOLBY LABORATORIES LICENSING CORPORATION.

MINI-

REPEATER

MAIN-

REPEATER

VIDEO

ANTENNA

BAL

300Ω

UNBAL

75Ω

GND

LOOP

ANTENA

SYSTEM CONTROL

IR OUT

PAL NTSC

FM 50kHz

/50μS

AM 9kHz

CHANNEL

/FM DE-

100kHz

/75μS

10kHz

STEP

EMPHASIS

OUT

MONITOR

PHONO

TAPE2

MONI-

TOR

TAPE1

OUT

TO MONITOR TV

VIDEO OUT

CONTROL

OUT

PRE

OUT

FRONT

SPEAKERS

SUB WOOFER

AC OUTLETS

CENTER

SPEAKERS

CENTER

SWITCHED

TOTAL 100W MAX

GND

REC

PLAY

PRE

OUT

PLAY

REC

OUT

VCR2

VCR1

/SAT

SEE INSTRUCTION MANUAL

MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES LICENSING CORPORATION.

"DOLBY","AC-3", "PRO LOGIC" AND THE DOUBLE-D SYMBOL ARE TRADEMARKS OF

DOLBY LABORATORIES LICENSING CORPORATION.

MINI-

REPEATER

MAIN-

REPEATER

RVIDEO

ANTENNA

UNSWITCHED

100W MAX

SPEAKER IMPEDANCE

8Ω∼16Ω／SPEAKER

BAL

300Ω

UNBAL

75Ω

GND

LOOP

ANTENA

SYSTEM CONTROL

IR OUT

CAUTION:

THE POWER

SUPPLY CORD SHOULD

BE DISCONNECTED

BEFORE CHANGING

THE VOLTAGE

SELECTOR.

TWO VOLTAGE SELECTORS

110V

120∼127V

220V

240V

CAUTION:

DO NOT CONNECT

TV SET CR MONITOR.

220V

110V 120-127V

240V

PAL NTSC

FM 50kHz

/50μS

AM 9kHz

CHANNEL

/FM DE-

100kHz

/75μS

10kHz

STEP

EMPHASIS

SPEAKER

IMPEDANCE

8Ω∼16Ω

／SPEAKER

OUT

MONITOR

REAR

SPEAKERS

I+II

I ONLY

SEE

INSTRUCTION

MANUAL

SPEAKER

SELECTOR

SPEAKER

IMPEDANCE

8Ω∼16Ω

／SPEAKER

/SAT LD

AC-3 •

DIGITAL IN

AC-3 •

RF IN

OUTPUT

LINE

REC

INPUT

PLAY

OUTPUT

L-AUDIO

(MONO)

AUDIO

LINE

REC

INPUT

PLAY

OUTPUT

REC

(L, R) PLAY

(L, R)

IN OUT

★

CONNECTIONS

AUDIO SYSTEM CONNECTIONS

NOTE:

Dolby Surround will not operate correctly if the signal passes

through a graphic equalizer.

When using Dolby Surround, turn off the TAPE 2 MONITOR

button or set the graphic equalizer for flat response or to its

through (defeat) setting.

To connect the Pioneer

S-W1000 Powered Sub-

woofer, connect from the

receiver’s SUB WOOFER

PRE OUT to the sub-

woofer input.

Cassette deck 2

Built-in amplifier

woofer, monaural

amplifier, etc.

Illustration shows Multi-voltage model.

★Connect when using a PIONEER projection monitor

receiver's built-in speaker as a center speaker.

Refer to the projection monitor's operating

instructions for details concerning connection and

operation.

When using a graphic equalizer

Cassette deck 2

Graphic equalizer

From L and R

REC jacks To L and R

PLAY jacks PIONEER Projection

monitor receiver

AC wall socket

CD playerCassette deck 1

Turntable

NOTE:

Before connecting pin jacks, speaker cables and other jacks and cables, switch power to the unit

OFF, and wait for about one hour. (When power is ON, the rear panel may become very hot.)

PHONO

TAPE2

MONI-

TOR

TAPE1

OUT

TO MONITOR TV

VIDEO OUT

CONTROL

OUT

PRE

OUT

FRONT

SPEAKERS

SUB WOOFER

AC OUTLETS

CENTER

SPEAKERS

CENTER

SWITCHED

TOTAL 100W MAX

GND

REC

PLAY

PRE

OUT

PLAY

REC

OUT

VCR2

VCR1

/SAT

SEE INSTRUCTION MANUAL

MINI-

REPEATER

MAIN-

REPEATER

RVIDEO

ANTENNA

UNSWITCHED

100W MAX

SPEAKER IMPEDANCE

8Ω∼16Ω／SPEAKER

BAL

300Ω

UNBAL

75Ω

GND

LOOP

ANTENA

SYSTEM CONTROL

IR OUT

CAUTION:

THE POWER

SUPPLY CORD SHOULD

BE DISCONNECTED

BEFORE CHANGING

THE VOLTAGE

SELECTOR.

TWO VOLTAGE SELECTORS

110V

120∼127V

220V

240V

CAUTION:

DO NOT CONNECT

TV SET CR MONITOR.

220V

110V 120-127V

240V

PAL NTSC

FM 50kHz

/50μS

AM 9kHz

CHANNEL

/FM DE-

100kHz

/75μS

10kHz

STEP

EMPHASIS

SPEAKER

IMPEDANCE

8Ω∼16Ω

／SPEAKER

OUT

MONITOR

REAR

SPEAKERS

I+II

I ONLY

SEE

INSTRUCTION

MANUAL

SPEAKER

SELECTOR

SPEAKER

IMPEDANCE

8Ω∼16Ω

／SPEAKER

/SAT LD

AC-3 •

DIGITAL IN

AC-3 •

RF IN

VIDEOVIDEO

(PLAY)

OUT

(REC)

AUDIO

VCR

VIDEOVIDEO

(PLAY)

OUT

(REC)

AUDIO

VIDEO

AUDIO

OUT VIDEO

OUT

AUDIO

OUT VIDEO

OUT

OUT IN

OUT

AC-3

RF OUT

VCR

CONNECTIONS

VIDEO SYSTEM CONNECTIONS THE S-VIDEO CONNECTORS

When using the VCR 1, LD and TO MONITOR TV jacks with

components which have S-VIDEO connectors, they can be

connected to the S-VIDEO connectors.

For the operation of components connected to S-VIDEO

connectors, refer to the instruction manuals of the

corresponding components.

NOTE:

In this unit, the S-VIDEO connectors (Y-C separate) and the

regular pin jacks are independent, so any signal input

through a pin jack must be output from the pin jack, and any

signal input through an S-VIDEO connector must be output

through the S-VIDEO connector.

Do not connect a different component to the same function's

S-VIDEO connector and regular pin jacks.

The S-VIDEO connector is for the video portion only, so be

sure to also make the audio connections.

How to use S-VIDEO connectors

AUDIOL R

VIDEO

PHONES

VIDEO

INPUT

SLEEP DIRECT

DOLBY SURROUND

Intelligent System Control

AC-3

PRO • LOGIC

AUDIO

OUT

VIDEO

OUT

FRONT PANEL

VCR (for playback only), or

another component such as a

TV camera.

NOTE:

Before connecting pin jacks, speaker cables and other jacks and cables, switch power to the unit

OFF, and wait for about one hour. (When power is ON, the rear panel may become very hot.)

VCR 2 TV Monitor

Illustration shows Multi-voltage model.

Do not place the AC-3

connection cord near

the antenna wires or

antenna terminals.

LD player TV tuner

VCR 1

AC wall socket

For the method of switching the TV monitor S-VIDEO

connector/VIDEO jack, refer to the TV monitor’s instruction

manual.

S-VIDEO jack

S-VIDEO plug

Check the position of

the holes and insert.

PRE

OUT

FRONT

SPEAKERS

SUB WOOFER

AC OUTLETS

CENTER

SPEAKERS

CENTER

SWITCHED

TOTAL 100W MAX

PRE

OUT

UNSWITCHED

100W MAX

SPEAKER IMPEDANCE

8Ω∼16Ω／SPEAKER

CAUTION:

THE POWER

SUPPLY CORD SHOULD

BE DISCONNECTED

BEFORE CHANGING

THE VOLTAGE

SELECTOR.

TWO VOLTAGE SELECTORS

110V

120∼127V

220V

240V

CAUTION:

DO NOT CONNECT

TV SET CR MONITOR.

220V

110V 120-127V

240V

REAR

SPEAKERS

I+II

I ONLY

SEE

INSTRUCTION

MANUAL

SPEAKER

SELECTOR

SPEAKER

IMPEDANCE

8Ω∼16Ω

／SPEAKER

I+II

I ONLY

–

PRE

OUT

FRONT

SPEAKERS

SUB WOOFER

AC OUTLETS

CENTER

SPEAKERS

CENTER

SWITCHED

TOTAL 100W MAX

PRE

OUT

UNSWITCHED

100W MAX

SPEAKER IMPEDANCE

8Ω∼16Ω／SPEAKER

CAUTION:

THE POWER

SUPPLY CORD SHOULD

BE DISCONNECTED

BEFORE CHANGING

THE VOLTAGE

SELECTOR.

TWO VOLTAGE SELECTORS

110V

120∼127V

220V

240V

CAUTION:

DO NOT CONNECT

TV SET CR MONITOR.

220V

110V 120-127V

240V

REAR

SPEAKERS

I+II

I ONLY

SEE

INSTRUCTION

MANUAL

SPEAKER

SELECTOR

SPEAKER

IMPEDANCE

8Ω∼16Ω

／SPEAKER

I+II

I ONLY

+–

SP-A(L) SP-A(R)

(L) (R)

FRONT

REAR

+–

–

––

–

+–

CENTER

CONNECTIONS

SPEAKER SYSTEM CONNECTIONS

NOTE:

Use speakers with an impedance of 8

Ω

to 16

Ω

When connecting speakers to the FRONT SPEAKERS B terminals,

the procedure is the same as that used for connecting speakers

to the FRONT SPEAKERS A terminals.

NOTE:

Do not allow any of the cord’s conductors to protrude from the

terminals or touch any other conductors. Malfunctioning or

breakdowns may occur when conductors come into contact

with each other.

If you have one pair of speakers only, connect it to front

speaker terminals A or B.

Be sure to connect single rear speaker to the L channel.

You can set this unit to match the requirements and

specifications of your stereo system’s speakers (whether or

not center speaker(s), rear speakers or a sub-woofer are

used, speaker size, etc.) to assure optimum sound quality.

Before using, perform settings in the SPEAKER MODE (refer

to page 29).

NOTE:

This unit does not feature conventional switching between

NORMAL/WIDE/PHANTOM center modes.

10mm (3/8 in)

1Push the lever forward.

2Insert the cord into the hole.

3Pull the lever back.

1Loosen cap.

2Insert wire.

3Tighten cap.

Connecting Two Center Speakers for Dual Center

There are two sets of terminals for center speakers on the main

unit, so you can connect two speakers. When you cannot install

a speaker under or behind your TV, installing speakers either

side of the TV as a center speaker is just as effective.

When the SPEAKER SELECTOR switch is in the “Ι + ΙΙ” position,

be sure to connect two speakers. If only one speaker is connected,

there will be no sound.

Both speaker systems should have an impedance of 4 Ω to 16 Ω.

Speaker cord connection

NOTE:

Before connecting pin jacks, speaker cables and other jacks and cables, switch power to the unit

OFF, and wait for about one hour. (When power is ON, the rear panel may become very hot.)

SPEAKER

SELECTOR

SPEAKER

SELECTOR

Illustration shows

Multi-voltage model.

Illustration

shows Multi-

voltage model.

CONNECTIONS

IR REPEATER CONNECTION

Connecting a supplied IR Repeater lets you also control other components with this unit’s remote control.

NOTE:

To operate components not made by Pioneer, perform REMOTE SET UP (page 31) after connecting an IR Repeater.

Remote control signals directed towards this unit or GUI operation signals are transmitted from the repeater as infrared signals, enabling

control of other components.

There are two kinds of infrared repeaters. Connect either or both to match the remote control requirements of different components.

MAIN-REPEATER

Use this to operate other components with this unit’s remote

control or to operate using GUI on-screen indications.

Install on top of this unit as shown in the figure.

MAIN-REPEATER

1Insert the REPEATER’s two

pegs into the holes on the top.

2Install the REPEATER laying

on its side on the top.

The pegs are usually

inserted in the two

rear holes.

Use the two front holes when

there’s another component on

top of this preventing easy

reception of the MAIN

REPEATER’s infrared signals.

VCR

MINI-REPEATER

Use this when a component operates incorrectly after receiving

a signal from this unit’s remote control, or when it is difficult for

a component to receive signals from the Main-Repeater. Stick it

directly on the remote control sensor window.

There are two MINI-REPEATER terminals.

If you need another Mini-Repeater, contact you nearest Pioneer

Service Center.

VCR

MINI-REPEATER

NOTE:

Before connecting the MAIN-REPEATER or MINI-REPEATER, switch power to the unit OFF, and wait

for about one hour. (When power is ON, the rear panel may become very hot.)

Illustration shows Multi-voltage model.

PHONO

TAPE2

MONI-

TOR

TAPE1

OUT

TO MONITOR TV

VIDEO OUT

CONTROL

OUT

GND

REC

PLAY

REC

OUT

VCR2

VCR1

/SAT

SEE INSTRUCTION MANUAL

MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES LICENSING CORPORATION.

"DOLBY","AC-3", "PRO LOGIC" AND THE DOUBLE-D SYMBOL ARE TRADEMARKS OF

DOLBY LABORATORIES LICENSING CORPORATION.

MINI-

REPEATER

MAIN-

REPEATER

RVIDEO

ANTENNA

BAL

300Ω

UNBAL

75Ω

GND

LOOP

ANTENA

SYSTEM CONTROL

IR OUT

PAL NTSC

FM 50kHz

/50μS

AM 9kHz

CHANNEL

/FM DE-

100kHz

/75μS

10kHz

STEP

EMPHASIS

OUT

MONITOR

VCR

1Remove the seal.

2 Stick onto the remote control

sensor window.

Illustration shows Multi-voltage model.

PHONO

TAPE2

MONI-

TOR

TAPE1

OUT

TO MONITOR TV

VIDEO OUT

CONTROL

OUT

GND

REC

PLAY

REC

OUT

VCR2

VCR1

/SAT

SEE INSTRUCTION MANUAL

MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES LICENSING CORPORATION.

"DOLBY","AC-3", "PRO LOGIC" AND THE DOUBLE-D SYMBOL ARE TRADEMARKS OF

DOLBY LABORATORIES LICENSING CORPORATION.

MINI-

REPEATER

MAIN-

REPEATER

RVIDEO

ANTENNA

BAL

300Ω

UNBAL

75Ω

GND

LOOP

ANTENA

SYSTEM CONTROL

IR OUT

PAL NTSC

FM 50kHz

/50μS

AM 9kHz

CHANNEL

/FM DE-

100kHz

/75μS

10kHz

STEP

EMPHASIS

OUT

MONITOR

VSX-D3S

NOTE:

To prevent possible damage, be careful to avoid accidentally

connecting the MINI-REPEATER to the MAIN-REPEATER

terminals.

PHONO

TAPE2

MONI-

TOR

TAPE1

OUT

TO MONITOR TV

VIDEO OUT

CONTROL

OUT

PRE

OUT

FRONT

SPEAKERS

SUB WOOFER

AC OUTLETS

CENTER

SPEAKERS

CENTER

SWITCHED

TOTAL 100W MAX

GND

REC

PLAY

PRE

OUT

PLAY

REC

OUT

VCR2

VCR1

/SAT

SEE INSTRUCTION MANUAL

MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES LICENSING CORPORATION.

"DOLBY","AC-3", "PRO LOGIC" AND THE DOUBLE-D SYMBOL ARE TRADEMARKS OF

DOLBY LABORATORIES LICENSING CORPORATION.

MINI-

REPEATER

MAIN-

REPEATER

RVIDEO

ANTENNA

UNSWITCHED

100W MAX

SPEAKER IMPEDANCE

8Ω∼16Ω／SPEAKER

BAL

300Ω

UNBAL

75Ω

GND

LOOP

ANTENA

SYSTEM CONTROL

IR OUT

CAUTION:

THE POWER

SUPPLY CORD SHOULD

BE DISCONNECTED

BEFORE CHANGING

THE VOLTAGE

SELECTOR.

TWO VOLTAGE SELECTORS

110V

120∼127V

220V

240V

CAUTION:

DO NOT CONNECT

TV SET CR MONITOR.

220V

110V 120-127V

240V

PAL NTSC

FM 50kHz

/50μS

AM 9kHz

CHANNEL

/FM DE-

100kHz

/75μS

10kHz

STEP

EMPHASIS

SPEAKER

IMPEDANCE

8Ω∼16Ω

／SPEAKER

OUT

MONITOR

REAR

SPEAKERS

I+II

I ONLY

SEE

INSTRUCTION

MANUAL

SPEAKER

SELECTOR

SPEAKER

IMPEDANCE

8Ω∼16Ω

／SPEAKER

/SAT LD

AC-3 •

DIGITAL IN

AC-3 •

RF IN

1 2 3 4

7 8 9

10 11 12 13

14 16 17 18 20 21 23 24 25 26 2715 19 22

CONTROL

OUT

CONTROL

REAR PANEL FACILITIES

Illustration shows Multi-voltage model.

1FM/AM ANTENNA terminals

Use these antenna terminals for reception of normal FM and AM

broadcasts.

2CHANNEL STEP switch

(Multi-voltage model only)

See page 4.

3PAL/NTSC switch

(Multi-voltage model only)

See page 4.

4TAPE 2 MONITOR jacks

Connect to audio components such as a second cassette deck or

a graphic equalizer.

5PHONO input jacks

Connect to the output cables from a turntable.

6GND terminal

Connect the turntable ground lead to this terminal.

7VCR 2 jacks

[VIDEO OUT]

Connect to the VCR 2 VIDEO INPUT jack.

[AUDIO OUT (L, R)]

Connect to the VCR 2 AUDIO INPUT jacks.

[VIDEO IN]

Connect to the VCR 2 VIDEO OUTPUT jack.

[AUDIO IN (L, R)]

Connect to the VCR 2 AUDIO OUTPUT jacks.

8VIDEO OUT (TO MONITOR TV) jack

Connect to a monitor TV or to TV sets with video input terminals

to watch program materials from a VCR or LD player connected

to this unit.

9CONTROL IN/OUT jacks

IN : Connect this jack to other Pioneer components when

using those components to control this unit.

OUT : Connect this jack to other Pioneer components when

using the remote control of this unit to control the other

components.

NOTE:

If there is a plug in this unit’s CONTROL IN jack, Intelligent

System Control and GUI operation are not possible.

The receiver’s remote sensor does not function when a plug is

inserted in the IN jack. To operate, point a remote control unit

other than this unit's supplied remote control unit at the

remote sensor on the component to which the receiver’s IN

jack is connected.

You cannot use the supplied remote control unit to operate this

unit via another component’s remote sensor.

To the CONTROL IN jack of

the PIONEER component

bearing the Î mark.

PIONEER component

bearing the Î mark.

Remote

control unit

0SYSTEM CONTROL IR OUT jacks

To operate other components with this unit’s remote control or

with GUI, connect the supplied repeater. (See page 10.)

MINI-REPEATER 1, 2:

Connect the supplied Mini-Repeater.

MAIN-REPEATER:

Connect the supplied Main-Repeater.

-SUB WOOFER PRE OUT jack

When you play back the low frequencies with a sub-woofer,

connect to a powered sub-woofer.

=CENTER PRE OUT jack

Connect when using a PIONEER projection monitor receiver's

built-in speaker as a center speaker.

Refer to the projection monitor's operating instructions for details

concerning connection and operation.

Receiver

REAR PANEL FACILITIES

~TWO VOLTAGE SELECTORS switches

(Multi-voltage model only)

See page 4.

!TAPE 1 jacks

Connect to the first cassette deck.

@CD input jacks

Connect to the output jacks of a compact disc player.

#VCR 1 jacks

[VIDEO OUT]

Connect to the VCR 1 VIDEO INPUT jack.

[AUDIO OUT (L, R)]

Connect to the VCR 1 AUDIO INPUT jacks.

[VIDEO IN]

Connect to the VCR 1 VIDEO OUTPUT jack.

[AUDIO IN (L, R)]

Connect to the VCR 1 AUDIO OUTPUT jacks.

$LD input jacks

Connect to an LD player’s output jacks (audio, video).

%TV/SAT (Satellite) jacks (input)

Use these jacks if you wish to connect a TV tuner with both video

and audio outputs.

^S (connector) video jacks

When used in conjunction with a VCR, LD player or TV monitor

equipped with S video jacks, connect to these jacks. (Refer to

page 8.)

÷TO MONITOR TV jack

This unit uses the TV screen to operate the system. Set the rear

panel PAL/NTSC switch (3) to match your TV's color system

(Multi-voltage model only). The screen will be unclear if the

color system does not match.

&AC-3 • DIGITAL IN (TV/SAT) jack

This jack is ready for future AC-3 system digital TV audio

broadcasts.

NOTE:

Do not connect to a CD or DAT coaxial digital audio output.

*AC-3 • RF IN (LD) jack

Connect to an LD player’s AC-3 • RF OUT jack.

(CENTER SPEAKERS terminals

Connect the center speaker(s) to these terminals.

NOTE:

Do not allow any of the cord’s conductors to protrude from the

terminals or touch any other conductors. Malfunctions or

breakdowns may occur when conductors come into contact

with each other.

Use a center speaker with an impedance of 8

Ω

to 16

Ω

. (If you

connect two center speakers, use speakers with an impedance

of 4

Ω

to 16

Ω

. Refer to

)REAR SPEAKERS terminals

Connect the rear speakers to these terminals.

NOTE:

Do not allow any of the cord’s conductors to protrude from the

terminals or touch any other conductors. Malfunctions or

breakdowns may occur when conductors come into contact

with each other.

Use rear speakers with an impedance of 8

Ω

to 16

Ω

_CENTER SPEAKER SELECTOR switch

This switch changes the speaker impedance when only one

center speaker is connected, or two speakers are connected.

When only one speaker is connected:

Be sure to set the switch to “Ι ONLY” (down side), and always

connect a speaker with an impedance of 8 Ω to 16 Ω to the Ι

terminal.

When two speakers are connected:

Be sure to set the switch to “Ι + ΙΙ” (up side), and always use

speakers with an impedance of 4 Ω to 16 Ω.

NOTE:

Switch the CENTER SPEAKER SELECTOR when the unit power

supply is at STANDBY. Do not switch the selector when the

power supply is at ON.

+FRONT SPEAKERS terminals

A : Connect to the first set of speakers.

B : Connect to the second set of speakers.

NOTE:

Do not allow any of the cord’s conductors to protrude from the

terminals or touch any other conductors. Malfunctions or

breakdowns may occur when conductors come into contact

with each other.

Use front speakers with an impedance of 8

Ω

to 16

Ω

¡AC OUTLETS

(U.S. and Canadian models)

[SWITCHED TOTAL 100 W (0.8 A) MAX]

Power supplied through these outlets is turned on and off by the

receiver’s POWER switch. Total electrical power consumption

of connected equipment should not exceed 100 W (0.8 A).

[UNSWITCHED 100 W (0.8 A) MAX]

Power flows continually to this outlet, regardless of whether the

receiver is switched ON or OFF. Electrical power consumption

of the connected equipment should not exceed 100 W (0.8 A).

(Multi-voltage model)

[SWITCHED TOTAL 100 W MAX]

Power supplied through these outlets is turned on and off by the

receiver’s POWER switch. Total electrical power consumption

of connected equipment should not exceed 100 W.

[UNSWITCHED 100 W MAX]

Power flows continually to this outlet, regardless of whether the

receiver is switched ON or OFF. Electrical power consumption

of the connected equipment should not exceed 100 W.

NOTE:

This unit should be disconnected by removing the power plug

from the wall socket when not in regular use, e.g. when on

vacation.

Do not connect appliances with high power consumption such

as heaters, irons or television sets to these AC OUTLETS in

order to avoid overheating and fire risk. This can cause the

receiver to malfunction.

CAUTION:

DO NOT CONNECT A MONITOR OR TV SET TO THIS UNIT'S AC

OUTLETS.

™Power cord

FRONT PANEL FACILITIES

5RESET button

Use this when normal operation is not possible because of

external influences such as static electricity, lightning or when

operations are not functioning even when operation buttons are

pressed. Press this button to return to normal operating

conditions.

(The input selector automatically switches to TUNER, and

SPEAKERS button A is the only one on.

Also, the tuner station memory, surround settings, and remote

control REMOTE SET UP settings are all returned to their initial

defaults.)

If you press this button when the power is ON, the unit switches

to POWER STANDBY.

6SPEAKERS buttons (A, B)

On/off switches for the A and B speaker systems.

7Input selector buttons

VCR 1 : Press when performing playback on a first VCR unit.

VCR 2 : Press when performing playback on a second VCR

unit.

VIDEO : Press when performing playback on a TV camera or

VCR connected to VIDEO INPUT jack on the front

panel.

TV/SAT : Press to watch TV broadcasts from the TV tuner

connected to the rear panel TV/SAT IN jacks.

LD : Press when performing playback on an LD player.

TAPE 1 : Press when performing playback on a cassette deck.

TAPE 2 MONITOR

:Press when performing playback on a second cassette

deck and when monitoring recording.

PHONO : Press when playing records on a turntable.

TUNER : Press when listening to radio broadcasts.

CD : Press when playing compact discs on a CD player.

8AC-3 button**/indicator

Switches AC-3 (Dolby Surround AC-3) on and off. (When the

input selector is set to a source other than LD or TV/SAT, it does

not operate.)

No sound will be heard if you turn on this switch when playing

an LD that does not use the AC-3 format.

** Setting is memorized separately for each input selector

button.

AUDIO/VIDEO STEREO RECEIVER

N∫m¿Û≤∫

POWER

STANDBY/ON

RETURN

SPEAKERS

TAPE 2

MONITOR PHONO TUNER

LD CD

SURROUND MODE

MASTER VOLUME

SUPER BASS

TREBLEBASS

MEMORY SELECT

FM/AM MPX MODE

GUI

MODE

AUDIOLR

VIDEO

PHONES

FLAT MAX

VIDEO

INPUT

TV/SAT

VIDEO

VCR 1 VCR 2 TAPE 1

AC-3

STANDBY

RESET

INPUT

ATT

GUI

ENTER

MIN MAX

MULTI-JOG

DSP OFF

TUNING MODE

SLEEP DIRECT

DOLBY SURROUND

Intelligent System Control

DOLBY

PRO-LOGIC

DSP MODE

SUPER

BASS

+–+–

AC-3 PRO • LOGIC

1 2

3 5

7 8 9

4 6

1310 12

14 15 16 17 18 24 25 2619 20 21 22 23

1Remote sensor

2POWER STANDBY/ON switch

This is the switch for electric power.

ON : When set to the ON position, power is supplied and

the unit becomes operational.

STANDBY : When set to the STANDBY position, the main power

flow is cut and the unit is no longer fully operational.

A minute flow of power feeds the unit to maintain

operation readiness.

(Timer ON/OFF possible)

When the unit is switched ON, ON/OFF control can be performed

by means of the optional timer.

NOTE:

When the power is initially turned ON, muting will be applied to

prevent sound from being output for about 5 seconds.

If the unit is on and you switch power off and then on again, it

takes about three seconds for operation to resume. This is not

a malfunction.

3STANDBY indicator

The STANDBY indicator lights when the power is set to STANDBY,

and goes out when set to ON.

4RETURN button

Press this button to return the receiver to its initial state. TUNER is

selected at this initial state. Adjust the sound level by using the

MASTER VOLUME control.

TAPE 2 MONITOR ...... OFF

DSP ............................. OFF

SUPER BASS .............. OFF

MUTING ....................... OFF

FUNCTION ............ TUNER

After pressing

And SPEAKERS buttons switch as follows.

Before pressing

the RETURN button

Both A and B are off Only A is on

Only A is on No change

Only B is on Both A and B are on

Both A and B are on No change

NOTE:

Press the RETURN button, and the frequency last selected is

received. If reception of the frequency last selected is not possible,

the mode automatically switches to AUTO TUNING.

360 30

0 (off) 2

FRONT PANEL FACILITIES

Auto stereo mode

Normally, leave in this mode for reception. When a stereo FM

broadcast is received, it will be automatically reproduced in

stereo.

Monaural mode

When receiving distant stations or stations with weak broadcast

signals, the input signal may be weak, thus resulting in increased

noise during FM stereo broadcasts. In this event, setting the

receiver to the monaural mode will reduce the noise. In this

case, however, FM stereo broadcasts will be reproduced in

monaural sound.

NOTE:

This button has no effect on reception of AM broadcasts.

MEMORY button:

Press this button to switch to the frequency preset mode.

SELECT button:

Press this button to switch to the station mode. Then you can

turn the multi-jog to select a station.

&DSP OFF button**

Switches DSP (( DSP MODE, * DOLBY PRO-LOGIC, 8 AC-3)

off.

*DOLBY* PRO-LOGIC button**

Switches DOLBY PRO-LOGIC SURROUND on and off.

(DSP MODE button**

Each time you press it, the mode and the display indications

change as follows:

)SUPER BASS button**

Press this button when you want to boost the bass.

_BASS control

Use to adjust the low-frequency level. Turn clockwise to boost

bass, and counterclockwise to attenuate bass.

+TREBLE control

Use to adjust the high-frequency level. Turn clockwise to boost

treble, and counterclockwise to attenuate treble.

¡SUPER BASS control

Use to adjust the bass boost level when the SUPER BASS button

is set to on.

** Setting is memorized separately for each input selector

button.

Manufactured under license from Dolby Laboratories Licensing

Corporation. Additionally licensed under Canadian patent number

1,037,877. “Dolby”, “AC-3”, “Pro Logic” and the double-D symbol

are trademarks of Dolby Laboratories Licensing Corporation.

Fabriqué sous licence de Dolby Laboratories Licensing Corporation

et sous le brevet suivant: Canada 1,037,877. DOLBY, AC-3, PRO

LOGIC et le symbole double-D, sont des marques de Dolby

Laboratories Licensing Corporation.

9MULTI-JOG

Use during tuner operation to select frequencies and station

numbers. During GUI operation, use to move the on-screen

cursor.

0GUI ENTER button (GUI operation)

Press to execute an operation selected with the MULTI-JOG.

-INPUT ATT button

Press on, and audio input sensitivity is attenuated (–10 dB) to

prevent clipping due to excessively high input levels. Switch

this on if the overload indicator in the display section lights

during playback. When you switch it on, the ATT indicator

lights.

NOTE:

Operates only when a DSP mode other than AC-3 is on.

=GUI MODE button

Switches GUI MODE on and off.

~MASTER VOLUME control

Use it to simultaneously adjust the sound volume from the

front, center, and rear speakers.

!SLEEP button/indicator

Activates the SLEEP timer. The length changes in the following

manner each time the button is pressed:

Unit: minutes

@PHONES jack

Connect the plug on your headphones to this jack. Set SPEAKERS

A and B switches to off if you want to cut the sound from the

speakers and listen to it only through the headphones.

#VIDEO INPUT jacks

VIDEO components such as a VCR or TV camera, etc. can be

connected.

$DIRECT button**/indicator

Press this to listen to source sound without passing the audio

signal through sound quality and balance adjusting circuitry.

DSP, super bass, INPUT ATT, rear and center speakers are

automatically switched off.

%Display section

See page 15.

^TUNING MODE buttons

FM/AM button:

Use this to switch between FM and AM frequency band reception.

MPX MODE button:

Use to select the auto stereo mode or monaural mode when

listening to FM broadcasts. The monaural mode has been

selected when the MONO indicator in the display section is lit.

JAZZ

3DANCE HALL

SIMULATED

SURROUND

THEATER

off

FRONT PANEL FACILITIES

DISPLAY SECTION

ALFE indicator

During Dolby AC-3 mode operation, if the LFE (Low Frequency

Effect) channel is set in the program source, “LFE” lights, and if

there is an LFE signal, a frame “ ” lights.

BDolby AC-3 channel indicator

During Dolby AC-3 mode operation, the channel set in the

program source is indicated.

CDOLBY SURROUND AC-3 indicator

DDOLBY PRO LOGIC indicator

EDSP MODE indicators

FSP (SPEAKERS) A, B indicators

Shows which speaker system (or systems) are switched on.

GOverload indicator

This lights when input signal level is excessive.

If it lights during playback, press the INPUT ATT button on, and

the ATT indicator lights.

Operates only when a DSP mode other than AC-3 is on.

HATT indicator

This lights when the INPUT ATT button is on.

ISUPER BASS indicator

This lights when the SUPER BASS button is on.

JTuning indicators

ST (STATION) CALL

:Press the SELECT button to switch to the station

mode and this indicator lights.

MONO : Lights up when the FM MONO mode is selected

with the MPX MODE button.

TUNED : Lights up when a station is tuned.

STEREO : Lights up when a stereo FM broadcast is being

received.

KTAPE 2 indicator

Lights up when the input selector is set to TAPE 2 MONITOR on.

LCharacter display

ST CALL

MONO

TUNED

STEREO

kHz

MHz

DSP MODE

JAZZ DANCE HALL

SIM SURR THEATER

DOLBY

PRO LOGIC

TAPE 2

LFE

DOLBY

SURROUND

AC-3 SUPER BASS

ATT

SP AB

A B C D E F G H I

J K L

OPERATING THE TUNER

Press the POWER switch to the ON position.

Select TUNER with the input selector button.

Be sure to turn the TAPE 2 MONITOR button off when listening to

AM or FM broadcasts.

Switch on the SPEAKERS button corresponding to the speakers

you wish to use.

FM auto stereo reception and monaural reception

Each time you press the MPX MODE button, the MONO indicator

in the display section lights or goes out.

÷If an FM stereo broadcast is received when the MONO indicator

is out, the STEREO indicator lights and sound is in stereo.

÷If an FM stereo broadcast is received when the MONO indicator

is lit, the sound will be monaural. If there is interference during

stereo mode reception, switch to mono. The sound will become

monaural but interference will be reduced.

TUNING INTO STATIONS

Turn the MULTI-JOG and the tuning frequency changes.

(Switch off when the GUI MODE button is on.)

Turning in a clockwise direction raises the frequency, while

turning in a counterclockwise direction lowers the frequency.

FREQUENCY PRESETTING

Switch off when the GUI MODE button is on.

1. Tune into the desired station.

See the section “TUNING INTO STATIONS”.

In addition to station frequencies, the MPX MODE (auto

stereo mode or monaural mode) can also be preset (FM

only).

2. Press the MEMORY button.

The station (channel) number flashes in the display. (Memory

mode.)

3. Turn the MULTI-JOG to select the station (channel) you

want to memorize.

4. Press the MEMORY button.

÷The station (channel) number lights in the display, indicating

that it has been memorized.

÷If you do not press the MEMORY button within about five

seconds after selecting a station, the memory mode is

canceled.

5. Repeat steps 1 to 4 to preset additional stations.

A total of 30 AM and FM stations may be preset. When you

store a new preset, it takes the place of the previously stored

station (if any).

You can also preset using GUI. (Refer to page 25.)

LISTENING TO BROADCASTS USING

PRESET TUNING

1. Use the FM/AM button to select either FM or AM.

When the “ST CALL” indicator is lit in the display, press the

SELECT button to switch it off.

2. Turn the MULTI-JOG until you reach the frequency of a

desired station.

When a station is received, the TUNED indicator will light up.

NOTE:

The TUNED indicator may not light with broadcasts received

over long distances, or when the broadcast signals are extremely

weak.

3. Adjust the volume and tone as desired.

Auto tuning

Auto tuning is convenient when you do not remember the

frequency of a desired station, or when you wish to find stations

that you do not normally listen to.

Operate by remote control. (Refer to page 23.)

You can also perform Auto Tuning using GUI. (Refer to page 25.)

Switch off when the GUI MODE button is on.

1. Press the SELECT button.

The “ST CALL” indicator lights in the display and the mode

switches to station call.

2. Turn the MULTI-JOG to select a station.

3. Adjust the volume and tone as desired.

When operating by remote control, press the ST +/– buttons to

select a memorized station. (Refer to page 23.)

With GUI, you can also select preset channels. (Refer to page 25.)

GUI MODE

SELECT

GUI MODE

2, 4

GUI MODE

MPX MODE

OPERATING THE TUNER

NOTE:

Even if the receiver’s power cord is unplugged, data remains in

memory for several days. If the contents of the memory are

erased, preset once more.

Last station memory

When the POWER switch is pressed to turn the power on, the

last station received before the power was previously turned off

will be tuned in again. When the power is ON, if the FM/AM

button is pressed, the last station received before the FM/AM

button was previously pressed will be tuned in again.

RECEIVING FM SIMULCAST TV PROGRAMS

By combining a TV set with this receiver, you can receive FM

simulcast TV programs (stereo TV sound transmitted from an

FM radio station) while viewing the video portion on your TV.

1. Select the desired TV program with the TV set.

2. Tune in the desired FM simulcast TV program on the receiver.

3. Adjust the volume and tone controls as desired.

OPERATING THE AUDIO/VIDEO COMPONENTS

Press the power switch to the ON position, and turn on the power

to the other components you wish to use (for example, TV, VCR,

cassette deck, etc.).

PLAYBACK

1. Use the input selector buttons to select the desired program

source.

If you select a music source other than TAPE 2, switch off the

TAPE 2 MONITOR.

2. Operate the appropriate audio/video component to playback

the program source.

For a video source, switch the TV connected to this unit to the

video input mode.

3. Adjust the volume and tone controls as desired.

Refer to page 19 for details concerning surround operation.

(Surround operation is also possible with GUI. Refer to page

24.)

Input selector

VCR 1

VCR 2

VIDEO

TV/SAT

TAPE 1

TAPE 2 MONITOR

PHONO

Program Source

To watch a video cassette tape on

the VCR connected to VCR 1 jacks.

To watch a video cassette tape on

the VCR connected to VCR 2 jacks.

To watch a VCR connected to

VIDEO INPUT jacks on front panel.

To watch the TV picture from a TV

tuner connected to the TV/SAT

jacks.

To watch a LaserDisc.

To listen to a tape on the cassette

deck connected to TAPE 1 jacks.

To listen to a tape on the cassette

deck connected to TAPE 2

MONITOR jacks.

To listen to a record.

To listen to a compact disc.

TAPE 2 MONITOR

RECORDING WITH A CASSETTE DECK

RECORDING WITH TAPE 1

If the TAPE 2 MONITOR button is on, press to turn off.

USING VCR 1, VCR 2 FOR AUDIO RECORDING

The audio signal output from the VCR 1 and VCR 2 AUDIO OUT

jacks is the same as that output from the TAPE 1 REC jacks, so

you can record using the same procedure as for recording with

TAPE 1.

COPYING TAPES

The following operations concern TAPE 1 to TAPE 2 copying.

1. Press the TAPE 1 input selector button.

2. Load the TAPE 1 cassette deck with a tape to playback.

3. Load the TAPE 2 cassette deck with a tape to record to.

4. Start recording on the TAPE 2 cassette deck.

5. Start playback on the TAPE 1 cassette deck.

The following operations concern TAPE 2 to TAPE 1 copying.

1. Select a source other than TAPE 1 with the input selector

buttons.

2. Press the TAPE 2 MONITOR button to turn it on.

3. Load the TAPE 2 cassette deck with a tape to playback.

4. Load the TAPE 1 cassette deck with a tape to record to.

5. Start recording on the TAPE 1 cassette deck.

6. Start playback on the TAPE 2 cassette deck.

Tape monitoring

When recording is performed on a cassette deck equipped with

a monitoring function, the recorded sound can be monitored

through the speaker system by pressing the TAPE 2 MONITOR

button to ON.

1. Select the source you want to record from with the input

selector buttons.

When recording AM or FM broadcasts, select a preset station

using the MULTI-JOG. If the desired station has not been

preset, tune in the station.

2. Start recording on TAPE 1 cassette deck.

3. Play the desired program source (record, compact disc, etc.).

The volume, balance and tone controls have no effect on the

recording.

RECORDING WITH TAPE 2

1. Select the source you want to record from with the input

selector buttons.

2. Start recording on the TAPE 2 cassette deck.

3. Play the desired program source (record, compact disc, etc.).

The volume, balance and tone controls have no effect on the

recording.

TAPE 2 MONITOR

VIDEO RECORDING

Refer to the connection procedures on pages 8 to 10 and refer

to the VCR’s Operating Instructions regarding proper operation

procedures. Recording can be performed on both VCR 1 and

VCR 2.

1. Select the source you want to record from with the input

selector buttons.

÷When recording from a LaserDisc on VCR 1 or VCR 2 = LD

÷When recording from the TV tuner on VCR 1 or VCR 2

= TV/SAT

÷When recording from VCR 1 on VCR 2 = VCR 1

÷When recording from VCR 2 on VCR 1 = VCR 2

÷When recording on VCR 1 or VCR 2 from a component

connected to the front panel VIDEO INPUT jacks = VIDEO

2. Start recording on the VCR.

For VCR, select a line input (external input).

3. Start playback on the component selected with the input

selector buttons.

The volume, balance and tone controls have no effect on the

recording.

NOTE:

When recording with VCR 1, be sure the input selector is set to

a position other than VCR 1. When recording with VCR 2, be sure

the input selector is set to a position other than VCR 2.

GUI operation enables easy copying from a LaserDisc to VCR 1

(or 2), and copying between VCR 1 and VCR 2. (Refer to page 28.)

SURROUND EFFECT

1. Select the desired mode with the DOLBY PRO-LOGIC button,

DSP MODE button and AC-3 button.

The DSP MODE changes in sequence each time the DSP

MODE button is pressed. (The DSP MODE indicator lights.)

÷Press the DSP OFF button to switch the DSP off.

÷If rear speakers are not selected during SPEAKER MODE

setting (page 29), pressing the DOLBY PRO-LOGIC button

selects DOLBY 3CH LOGIC.

2. Adjust levels to achieve a correct surround sound

reproduction.

This is done using GUI (page 24). For details concerning how

to perform level adjustment, refer to page 30.

JAZZ

3DANCE HALL

SIMULATED

SURROUND

THEATER

off

You can set this unit to match the requirements and

specifications of your stereo system’s speakers (whether or

not center speaker(s), rear speakers or a sub-woofer are

used, speaker size, etc.) to assure optimum sound quality.

Before using, perform settings in the SPEAKER MODE (refer

to page 29).

NOTE:

This unit does not feature conventional switching between

NORMAL/WIDE/PHANTOM center modes.

REMOTE CONTROL OPERATION

PUTTING BATTERIES INTO THE REMOTE

CONTROL UNIT

REMOTE CONTROL RANGE

1. Open the battery compartment cover on the rear of the

remote control unit. The cover should open easily if you slide

it in the direction of the arrow while pressing on it with your

thumb.

2. Press the RESET button in the center hole of the battery

compartment.

3. Take out the two supplied batteries size “AA” (IEC R6P), and

insert them into the battery compartment in accordance

with the indications in the compartment.

4. Close the cover of the battery compartment.

Incorrect use of batteries may lead to leakage or

rupture. Always be sure to follow these guidelines:

Always insert batteries into the battery compartment correctly

matching the positive ª and negative · polarities, as indicated

inside the compartment.

Never mix new and used batteries.

Batteries of the same size may have different voltages, depending

on their type. Do not mix different types of batteries.

When operating the remote control unit, point the front of the

unit at the front panel of the receiver. The remote control unit

may be used within a range of about 7 meters (23 feet) from the

remote sensor, within angles of up to about 30 degrees.

Performance of the remote control unit is adversely affected in

the presence of a strong fluorescent light. Keep such lights

away, especially from the sensor window.

Battery Replacement

As battery power runs down, the range over which the remote

control unit can operate decreases. Also, ONE TOUCH

OPERATION and other buttons light less brightly.

When the range becomes too short, change the batteries.

–+

–

30°

7m (23 feet)

30°

REMOTE CONTROL OPERATION

RECEIVER CONTROL BUTTONS 4ONE TOUCH OPERATION buttons

VCR 1/2, CD, LD, TAPE:

Pressing these buttons automatically calls up “ONE TOUCH

OPERATION SET UP” settings, made using GUI (page 33).

TUNER:

This switches power to the TUNER ON and starts reception of the

last memorized station.

Also, if power to this unit is OFF, it is switched ON and operation

automatically switches to the selected function. When you press

any of the ONE TOUCH OPERATION buttons, the GUI MODE

switches off.

5FUNC. (function) button

Press to select the receiver input.

6TAPE 2 (TAPE 2 MONITOR) button

Switches TAPE 2 MONITOR on and off.

7GUI button

Switches GUI MODE on and off.

When the GUI mode is on, the 9 Select/Adjust buttons (%, #, ﬁ,

@) light.

8M.CHECK (Mode check) button

Indicates whether the GUI MODE is on or off.

When it is on, %, #, ﬁ, @ light. When it is off, a 4 ONE TOUCH

OPERATION button lights to indicate the current function.

If you press the button again while it is lit, remote control

functions change. When the remote control is in the GUI mode,

the 9 Select/Adjust buttons (%, #, ﬁ, @) light.

9Select/Adjust buttons (%, #, ﬁ, @)

When the GUI mode is on, %, #, ﬁ and @ light.

When using the GUI function with the on-screen display, use for

such operations as selection and adjustments (by moving the

cursor).

When the GUI mode is off, use to operate other components.

0MUTE button

Used to temporarily mute the sound. When it’s in the on position,

the indicator on the MASTER VOLUME knob flashes. The volume

is restored when pressed again.

OPERATING OTHER COMPONENTS

REMOTE CONTROLLING OF ANY OTHER OF YOUR

AUDIO-VISUAL COMPONENTS VIA THIS UNIT

REQUIRES:

All components must be remote controllable (have a sensor

window on the front panel) to receive a direct command from

this unit, upon successful learning of those commands by

this programmable unit.

When operating components other than the receiver:

1. Press the ONE TOUCH OPERATION button for the component

you want to operate.

2. Press the operation button.

NOTE:

Components that could not originally be operated by remote

control cannot be controlled by this unit’s remote control.

VCR 1

3VCR 2 VIDEO TV/SAT LD

CD TUNER PHONO TAPE 1

333 3

222

1RECEIVER POWER button

Switches the receiver power between ON and STANDBY.

2ENTER button

When GUI is on, press to execute an operation selected with the

Select/Adjust buttons.

3VOLUME +, – buttons

Adjusts the overall volume.

TV FUNC.

TV VOL.

TV CH

TV POWER

CDVCR 1

TUNER

FUNC. TAPE2 MUTE

RECEIVER

POWER

ST+ST–

ENTER

＋

−

＋

−

ONE TOUCH OPERATION

VCR 2 TAPE

FOR AV RECEIVER

FQ +

FQ -

REMOTE CONTROL OPERATION

VCR 1/VCR 2 operation

1POWER button:

Switches VCR power ON/OFF.

21 (REW) button:

Rewinds the tape and allows picture search.

37 (STOP) button:

Stops the tape transport.

48 (PAUSE/STILL) button:

Sets pause and still picture.

5¡ (FF) button:

Rapidly advances the tape and allows picture search.

63 (PLAY) button:

Selects playback.

LD player operation

1POWER button:

Switches LD player power ON/OFF.

21 (SCAN/CHAPTER SEARCH) button:

Pressing quickly once takes you to the start of the chapter

currently playing. Each time you press it, you move back to

the start of the previous chapter. Continue pressing for fast

reverse.

37 (STOP) button:

Playback is stopped when pressed once.

With some LD players, pressing the button twice may open

the disc tray.

48 (PAUSE) button:

Video and audio are stopped and playback is paused.

5¡ (SCAN/CHAPTER SEARCH) button:

Pressing quickly once takes you to the start of the next

chapter. Each time you press it, you move ahead to the start

of the next chapter. Continue pressing for fast forward.

63 (PLAY) button:

Selects playback.

CD player operation

1POWER button:

Switches CD player power ON/OFF.

21 (MANUAL/TRACK SEARCH) button:

Pressing quickly once takes you to the start of the track

currently playing. Each time you press it, you move back to

the start of the previous track. Continue pressing for reverse

search.

Pressing the 1 button while pressing the 7 button takes

you to the previous disc. (With a file-type CD player.)

37 (STOP) button:

Stops playback.

48 (PAUSE) button:

Pauses playback.

5¡ (MANUAL/TRACK SEARCH) button:

Pressing quickly once takes you to the start of the next track.

Each time you press it, you move ahead to the start of the

next track. Continue pressing for forward search.

Pressing the ¡ button while pressing the 7 button takes

you to the next disc. (With a file-type CD player.)

63 (PLAY) button:

Selects playback.

ONE TOUCH OPERATION buttons

switch between each of the functions.

TV operation

7TV POWER button:

Switches the power of the TV ON/OFF.

8TV CH (channel) +, – button:

Switches TV channels in order.

9TV VOL (volume) +, – button:

Raises (+) and lowers (–) the volume.

0TV FUNC. (function) button:

Used to change the TV FUNCTION.

TV FUNC. button cannot be used with some PIONEER TVs.

TV FUNC.

TV VOL.

TV CH

TV POWER

CDVCR 1

TUNER

FUNC.

TAPE2 MUTE

RECEIVER

POWER

ST+ST–

ENTER

＋

−

＋

−

ONE TOUCH OPERATION

VCR 2 TAPE

FOR AV RECEIVER

FQ +

FQ -

REMOTE CONTROL OPERATION

TAPE operation

1POWER button:

Switches cassette deck power ON/OFF.

21 (FF) button:

Rapidly advances the tape in the direction of the arrow.

37 (STOP) button:

Stops the tape transport.

48 (PAUSE) button:

Temporarily stops tape transport. Press again to resume

tape transport.

5¡ (FF) button:

Rapidly advances the tape in the direction of the arrow.

63 (PLAY) button:

Selects playback.

NOTE:

On a Pioneer double deck, you can operate Deck II.

Tuner operation

2ST – (Station Down) button:

Used for recalling memorized stations.

3FQ – (Frequency Down) button:

Shifts the frequency down.

4FQ + (Frequency Up) button:

Shifts the frequency up.

5ST + (Station Up) button:

Used for recalling memorized stations.

6Band button:

Switches the FM and AM bands in turn.

Auto tuning:

Press FQ + (up) or – (down) button until the frequency starts to

change, then release it. The tuner will automatically search for

a broadcasting station and stops when one is found, and the

TUNED indicator lights up. To search for another station, press

again.

Manual tuning:

Press FQ + (up) or – (down) button and release quickly. The

tuning frequency will change by one step each time the button

is pressed. Press as many times as necessary to tune in the

desired station. The TUNED indicator lights up when the station

is tuned in best.

÷If you keep the FQ (up/down) button depressed after the

frequency has began to change, the reception frequency

changes continuously, and stops when the button is released.

NOTE:

When AUTO TUNING is in use, reception may not be possible

over long distances or when signals are weak. At these times

MANUAL TUNING is recommended.

SET

SOUND

ED I T

SUPER

BASS

DSP

MODE

DOLBY

PROLOGIC

DIRECT

DOLBY

PROLOGIC

SUPER

BASS

THEATER

DOLBY

PROLOGIC

SUPER

BASS

A B DISPLAY

D/A/CX AUDIO

min

＋

1 2 3 4 510

6 7 8 9 0

VCR 1

THEATER

1 2 3 4 5 6 7 8 9

10 11 12

SYSTEM

OFF

SLEEP

SEL

COPY

AC-3

SET

SOUND

ED I T

SUPER

BASS

DSP

MODE

DOLBY

PROLOGIC

DIRECT

AC-3

OPERATING USING GUI

GUI

GUI (Graphic User Interface) lets you use the TV screen to

operate the system.

÷Press the GUI MODE button on this unit or the GUI button on

the remote control and operation indications for the currently

selected function are displayed on the TV screen.

÷To operate, use the %, #, ﬁ, @ buttons on the remote control

(they light up when the GUI mode is on) or the MULTI-JOG on

this unit to move the cursor (the hand shaped mark) displayed

on the TV screen. When the cursor is on the button you want

to operate, press the GUI ENTER button.

(Figure 1: Main Menu display)

1AC-3:

Switches DOLBY SURROUND AC-3 on/off.

When on, “AC-3” is displayed on the right of the function

indications. (When the input selector is set to a source other

than LD or TV/SAT, it does not operate. Also, when TAPE 2 is on,

it does not operate.)

2DOLBY PRO-LOGIC:

Switches DOLBY PRO-LOGIC on/off.

When on, “DOLBY PRO-LOGIC” is displayed to the right of the

function indications.

3DSP MODE:

Switches between the five DSP modes as follows:

The selected mode is displayed to the right of the function

indications.

4SUPER BASS:

Switches SUPER BASS on/off.

When on, “SUPER BASS” is displayed on the right of the

function indications.

5DIRECT:

Press this to listen to source sound without passing the audio

signal through sound quality and balance adjusting circuitry.

The surround mode, rear and center speakers are automatically

switched off.

6SOUND EDIT:

Press to make adjustments such as level setting for the currently

selected DSP mode, DOLBY SURROUND AC-3 or DOLBY PRO-

LOGIC.

When you press this button, the display changes to SOUND

EDIT indications. (Refer to page 30.)

7SET UP:

Press this button and the display changes to the SET UP MENU.

(Refer to pages 31

–

33.)

8Display change button:

Switches between Main Menu display (Figure 1) and Sub Menu

display (Figure 2).

9COPY:

Press to copy from a LaserDisc to a VCR, or to copy between VCR

1 and VCR 2.

When you press this button, the display changes to COPY

indications. (This button is displayed only when the function is

LD, VCR 1 or VCR 2. Refer to page 28.)

0V.SEL (VIDEO SIGNAL SELECTOR):

This switches only the video signal in sequence, leaving the

sound unchanged. (Refer to page 28.)

-SLEEP:

This operates the sleep timer. Move the cursor to this button,

and each time you press the GUI ENTER button, timer settings

change as follows:

=SYSTEM OFF:

Switches power to this unit, the TV and the currently selected

function off.

NOTE:

When you press the SYSTEM OFF button, power to components

not made by Pioneer switches on if power to these components

was already switched off.

÷When the operating instructions say “Press the button”, this

means move the cursor to the desired button and press the

GUI ENTER button.

NOTE:

If you do not perform any of the operations above within 10 ~ 30

seconds, the GUI display is canceled.

<Multi-voltage model only>

Set the rear panel PAL/NTSC switch to match your TV’s color

system. The screen will be unclear if the color system does not

match.

RECEIVER CONTROL BUTTONS

÷The buttons in the following explanation are the receiver operation button indications common to all function displays. (The illustration

shows LD operation indications.)

(Figure 2: Sub Menu display)

JAZZ

DANCE HALL

SIM.SURR

(SIMULATED SURROUND)

THEATER

off

VCR 1

3VCR 2 VIDEO TV/SAT LD

off

333 3

90 min

60 min 30 min

0 min (off)

MEMORY

TUNER

87.50

MHz

SUPER

BASS

DOLBY

PROLOGIC

+–

BAND

SET

SOUND

ED I T

SUPER

BASS

DSP

MODE

DOLBY

PROLOGIC

DIRECT

AC-3

21 43

BAND

TUNER

87.50

MHz

DOLBY

PROLOGIC

SYSTEM

OFF

SLEEP

min

87.50

98.00

106.70

530

100.00

89.50

1440

620

108.00

MHz

KHz

MHz

KHz

MHz

SEL

VCR 1

+–

SUPER

BASS

MEMORY

SET

SOUND

ED I T

SUPER

BASS

DSP

MODE

DOLBY

PROLOGIC

DIRECT

AC-3

OPERATING THE TUNER (GUI OPERATION)

Calling up the tuner display.

1. Press the TUNER button of the input selector.

2. Press the GUI MODE button on this unit or the GUI button on

the remote control.

TUNER operation indications are displayed.

(Main Menu display) (Sub Menu display)

1Channel indication:

Indicates the current channel.

2–, + buttons:

Use to raise or lower the frequency.

3Frequency indication:

Indicates the current frequency.

4BAND button:

Switches between FM/AM. The band changes each time you press

this button and is displayed next to the frequency indication.

5NEXT button:

Switches between channel lists. There are a total of thirty channels,

from 1 to 30, displayed 10 at a time on three lists which change each

time you press the button as follows.

6Channel list:

Frequencies memorized in each channel are displayed. Press a

number button and that channel’s frequency is received.

7MEMORY button:

Use to memorize stations.

You can only press this button when a channel list is displayed

(Sub Menu display).

1~10

311~20 21~30

PRESET TUNING

You can preset up to 30 FM/AM stations for easy recall.

FREQUENCY PRESETTING

1. Press to switch to the Sub Menu display.

(The channel list is displayed.)

2. Tune in the desired station.

Refer to “MANUAL/AUTO TUNING” procedures.

In addition to station frequencies, the MPX MODE can also be

preset (FM only).

Switch to the MPX MODE using the MPX MODE button on this

unit. (No indications are displayed.)

3. Press the MEMORY button.

Channel indications “– –” flash.

4. Select the channel you want to memorize from the channel

list and press the GUI ENTER button.

This memorizes the frequency.

To memorize other stations, repeat steps 2 through 4.

MANUAL/AUTO TUNING

1. Move the cursor to BAND, and select FM or AM.

The band changes each time you press the GUI ENTER button.

2. Move the cursor to + or – and press the GUI ENTER button

to raise or lower the frequency as desired.

÷One Step Tuning:

Press the GUI ENTER button and release quickly. The frequency

will change by one step each time the button is pressed. Press as

many times as necessary to tune in the desired station.

÷Auto Tuning:

Press the GUI ENTER button until the frequency starts to change

(about 1 sec.), then release it. The tuner automatically searches for

a broadcasting station and stops when one is found.

NOTE:

When the signal level is too weak for reception, the unit cannot

perform Auto tuning. In this case, change to Manual tuning.

÷High Speed Manual Tuning:

Keep the GUI ENTER button pressed. The frequency changes

continuously and stops when the button is released.

DOLBY

PROLOGIC

CH −CH ＋MTS ANT

SYSTEM

OFF

SLEEP

min

SEL

VCR 1

1 2 3 4 5 6 7 8 9 0

SUPER

BASS

SET

SOUND

ED I T

SUPER

BASS

DSP

MODE

DOLBY

PROLOGIC

DIRECT

AC-3

DOLBY

PROLOGIC

SUPER

BASS

CH −CH ＋MTS ANT

SET

SOUND

ED I T

SUPER

BASS

DSP

MODE

DOLBY

PROLOGIC

DIRECT

AC-3

DOLBY

PROLOGIC

SUPER

BASS

TAPE 1

DECK

ΙΙ

TAPE 2

SET

SOUND

ED I T

SUPER

BASS

DSP

MODE

DOLBY

PROLOGIC

DIRECT

AC-3

DOLBY

PROLOGIC

SUPER

BASS

VCR1

CH＋MTS

SYSTEM

OFF

SLEEP

min

CH−

TV/

VCR

FUNC

0 1 2 3 4

5 6 7 8 9

SEL

VCR 1

SET

SOUND

ED I T

SUPER

BASS

DSP

MODE

DOLBY

PROLOGIC

DIRECT

AC-3

COPY

DOLBY

PROLOGIC

SUPER

BASS

VCR1

SET

SOUND

ED I T

SUPER

BASS

DSP

MODE

DOLBY

PROLOGIC

DIRECT

AC-3

OPERATING OTHER COMPONENTS (GUI OPERATION)

7:Stops tape transport.

8:Sets pause and still picture.

¶:Selects the recording mode.

3:Starts playback.

1:Rewinds the tape.

¡:Rapidly advances the tape.

NOTE:

Fast-forwarding or rewinding during playback may interfere with

GUI display.

0 ~ 9 : Use to call up channels.

CH + : Shifts channels in ascending order.

CH – : Shifts channels in descending order.

TV/VCR : This button can be used only for VCRs with a TV/VCR

selector.

Toggles the antenna output between TV and VCR.

FUNC : Switches the input selector functions.

MTS : Selects the reception mode for multi-channel TV sound.

Ι / ΙΙ / ΙΙΙ:Using the REMOTE SET UP learning function (page 32),

use to memorize commands.

<TAPE>

[DECK ΙΙ ]

7:Stops playback.

8:Temporarily stops tape transport.

3:Selects playback.

1:Rapidly advances the tape in the direction of the arrow.

¡:Rapidly advances the tape in the direction of the arrow.

TAPE 2 : Displayed when TAPE 2 MONITOR is on.

When using a single cassette deck, select DECK ΙΙ.

<TV>

CHANNEL 1 ~ 9, 0

:Used to call up channels.

For example, to receive channel “23”, press 2 and

then 3.

For channels 1 through 9, press the number and wait

for about 2 seconds.

[DECK Ι ]

7:Stops playback.

8:Temporarily stops tape transport.

3:Selects playback.

1:Rapidly advances the tape in the direction of the arrow.

¡:Rapidly advances the tape in the direction of the arrow.

1 ~ 6 : Selects the cassette No. (1 to 6) for multi-cassette

changer.

TAPE 2 MONITOR indicator

CH – : Shifts channels in descending order.

CH + : Shifts channels in ascending order.

MTS : Selects the reception mode for multi-channel TV sound.

ANT : Press to switch between ANTENNA-A and ANTENNA-

B when you wish to watch TV.

TAPE 1

SYSTEM

OFF

SLEEP

min

1 2 3 4 5 6

SEL

VCR 1

DECK ΙΙ

DECK

DOLBY

PROLOGIC

SUPER

BASS

SET

SOUND

ED I T

SUPER

BASS

DSP

MODE

DOLBY

PROLOGIC

DIRECT

AC-3

TRACK DISC＋

SYSTEM

OFF

SLEEP

DISC−

MODE

＋

DISC

min

1 2 3 4 5

6 7 8 91010

SEL

VCR 1

DOLBY

PROLOGIC

SUPER

BASS

THEATER

DOLBY

PROLOGIC

SUPER

BASS

THEATER

SET

SOUND

ED I T

SUPER

BASS

DSP

MODE

DOLBY

PROLOGIC

DIRECT

AC-3 SET

SOUND

ED I T

SUPER

BASS

DSP

MODE

DOLBY

PROLOGIC

DIRECT

AC-3

OPERATING OTHER COMPONENTS (GUI OPERATION)

<CD>

7:Stops playback.

8:Pauses playback.

3:Selects playback.

1:Selects fast backward.

¡:Selects fast forward.

4:Returns to the beginning of the track currently playing.

¢:Advances to the next track.

<LD>

7:Playback is stopped when selected once.

With some LD players, pressing the button twice may

open the disc tray.

8:Video and audio are stopped and playback is paused.

3:Selects playback.

1:Selects fast backward.

¡:Selects fast forward.

4:Searches for the start of the chapter currently playing.

¢:Searches for the start of the next chapter.

1 ~ 10 : For direct selection of a chapter.

+10 : Use to input such information as chapter numbers

higher than 10.

D/A/CX : Use to switch between LD digital/analog sound and

the CX system.

A:Selects playback of LD disc to side A.

B:Selects playback of LD disc to side B.

AUDIO : Switches speakers between STEREO, L and R.

DISPLAY : Switches TV screen display of chapter, frame/time

number on/off.

Ι / ΙΙ / ΙΙΙ :Using the REMOTE SET UP learning function (p. 32),

use to memorize commands.

1 ~ 10 : For direct selection of a track or programming of

tracks.

+10 : Use when selecting a track number higher than 10.

For example, to select 21, press the +10 button twice

and then the 1 button.

This button cannot be used with some CD players.

DISC : Before selecting a disc number button, select this

button first.

TRACK : Before selecting a track number button, select this

button first.

MODE : Use this button to switch between SINGLE and ALL

modes when using a File-type CD player.

To play only a single disc select SINGLE.

For search and continuous play of all discs select ALL.

DISC + : Use to select a disc number.

DISC – : Use to select a disc of the file-type CD player.

Ι / ΙΙ / ΙΙΙ :Using the REMOTE SET UP learning function (p. 32),

use to memorize commands.

DOLBY

PROLOGIC

SUPER

BASS

THEATER

DOLBY

PROLOGIC

SUPER

BASS

A B DISPLAY

D/A/CX AUDIO

min

＋

1 2 3 4 510

6 7 8 9 0

VCR 1

THEATER

SYSTEM

OFF

SLEEP

SEL

COPY

SET

SOUND

ED I T

SUPER

BASS

DSP

MODE

DOLBY

PROLOGIC

DIRECT

AC-3 SET

SOUND

ED I T

SUPER

BASS

DSP

MODE

DOLBY

PROLOGIC

DIRECT

AC-3

DOLBY

PROLOGIC

SUPER

BASS

VCR1

CH＋MTS

SYSTEM

OFF

SLEEP 90

min

CH−

TV/

VCR

FUNC

0 1 2 3 4

5 6 7 8 9

SEL VCR 1

SET

SOUND

ED I T

SUPER

BASS

DSP

MODE

DOLBY

PROLOGIC

DIRECT

AC-3

COPY

DOLBY

PROLOGIC

SUPER

BASS

A B DISPLAY

D/A/CX AUDIO

min

＋

1 2 3 4 510

6 7 8 9 0

VCR 1

THEATER

SYSTEM

OFF

SLEEP

SEL

COPY

SET

SOUND

ED I T

SUPER

BASS

DSP

MODE

DOLBY

PROLOGIC

DIRECT

AC-3

COPY

EXIT

START STOP

LD to VCR1

START STOP

LD to VCR2

COPY

EXIT

START STOP

VCR1 to VCR2

VCR 1 = VCR 2 or VCR 2 = VCR 1 Copying

(Example: VCR 1 =VCR 2)

1. Select VCR 1 with the FUNC. button and press to

switch to the Sub Menu display.

VCR 1 function indications are displayed.

COPY OPERATION (GUI OPERATION)

÷LD = VCR 1/2 and VCR 1 ÔVCR 2 copying is possible.

÷For VCR, select a line input (external input).

LD = VCR 1 (VCR 2) Copying

1. Select LD with the FUNC. button and press to switch

to the Sub Menu display.

LD function indications are displayed.

USING THE VIDEO SIGNAL SELECTOR (GUI OPERATION)

This function can be used to allow you to listen to the playback

sound while changing the video image only, thus allowing you

to playback and record video images different from the playback

sound source.

1. Select the component you want to listen to with the FUNC.

button.

When listening to (or recording) AM or FM broadcasts, select a

preset station. If the desired station has not been preset, tune in

the station.

2. Press the GUI button to switch the GUI mode ON.

GUI indications for the selected function are displayed.

3. Press to switch to the Sub Menu display.

(Example: TUNER)

4. Select the video component you want to watch with the

V.SEL (VIDEO SIGNAL SELECTOR) button.

5. Start playback of the component selected with the FUNC.

button and the component selected with the V.SEL button.

CAUTION:

If you must operate the V.SEL button during recording, do so

after setting the recording VCR to the pause mode. If the button

is operated when the tape is traveling during recording, the

recorded image and sound may be disrupted at the point at

which the button is operated.

2. Press the COPY button.

COPY indications are displayed.

2. Press the COPY button.

COPY indications are displayed.

3. Select the component you are using to copy (VCR 1 or VCR 2),

and press START.

The LD player starts playing and recording begins on the

VCR. To stop, press the STOP button.

3. Press START.

VCR 1 starts playing back and recording starts on VCR 2. To

stop, press the STOP button.

BAND

TUNER

87.50

MHz

DOLBY

PROLOGIC

SYSTEM

OFF

SLEEP 90

min

87.50

98.00

106.70

530

100.00

89.50

1440

620

108.00

MHz

KHz

MHz

KHz

MHz

SEL VCR 1

+–

SUPER

BASS

MEMORY

SET

SOUND

ED I T

SUPER

BASS

DSP

MODE

DOLBY

PROLOGIC

DIRECT

AC-3

÷If you press the SOUND EDIT button on a function operation

display, display switches to “SOUND EDIT” indications for the

currently selected surround mode. (Press the EXIT button to

return to the original function operation display.)

÷On the SOUND EDIT display, you can adjust levels and balances

set to the speaker mode, etc.

(When using PRO-LOGIC THEATER)

SOUND EDIT OPERATION (GUI OPERATION)

SETTING THE SPEAKER MODE

You can set this unit to match the requirements and specifications

of your stereo system’s speakers (whether or not center

speaker(s), rear speakers or a sub-woofer are used, speaker

size, etc.) to assure optimum sound quality.

÷Pressing the SPEAKER MODE button on the “SOUND EDIT”

display takes you to the “SPEAKER MODE” display.

LARGE SMALL NONE

333

LARGE x 2 SMALL x 2

NONE

333LARGE

SMALL 22

÷Set the SPEAKER MODE using the different buttons.

Selects the size of the front L, R speakers.

LARGE Ô SMALL

Selects center speaker size, or NONE if no center

speaker is used.

Selects the size and number (1 or 2) of rear speakers,

or NONE if no rear speakers are used.

During Pro-Logic reproduction, this unit does not let you

switch between NORMAL, WIDE, and PHANTOM center

mode settings. However, setting the SPEAKER MODE as

follows provides the same effects as these modes.

Front Center

LARGE SMALL \NORMAL

LARGE LARGE \WIDE

LARGE NONE \PHANTOM

Set the rear speaker to NONE for conventional 3CH Logic

reproduction.

Selects whether there is a sub-woofer or not.

USE ÔNONE

LFE MODE

÷Attenuate LFE (Low Frequency Effect = ultra-low bass effect for

more powerful movie sound or music) level. It changes in

sequence each time the button is pressed.

NOTE:

If you set to “+10 dB”, front three channel (L + R + C) output

power is required for the sub-woofer. If this is more power than

the sub-woofer can handle, clipping may occur resulting in

distortion.

LOW CUT FIL.

÷Switch ON if the sub-woofer does not have high power handling

capabilities. (This enables bass boosting while reducing the

possibility of the sub-woofer clipping.)

ON ÔOFF

CROSSOVER

– +

÷Set sub-woofer crossover frequency (highest frequency it can

reproduce). Press

–

to lower the crossover frequency and

press

to raise it. (100 Hz/150 Hz/200 Hz)

CENTER DELAY

S L

÷Sets center channel delay time. Press

for shorter delay,

press

for longer delay.

÷This is possible only when the AC-3 is selected.

REAR DELAY

S L

÷Set rear (surround) channel delay time. Press

for shorter

delay, press

for longer delay.

÷This is possible only when the AC-3 or PRO-LOGIC is selected.

Pressing

EXIT

returns you to SOUND EDIT display.

SUB

WOOFER

CENTER

SPEAKER

FRONT

SPEAKER

REAR

SPEAKER

MODE

TEST

TONE

CENTER LEVEL

REAR LEVEL

SUB WF LEVEL

EFFECT LEVEL

–

+10

–10

EXIT

SOUND EDIT

PRO-LOGIC THEATER

F - L

MASTER BALANCE

REAR BALANCE

+10 dB 0 dB OFF

333

FRONT

SPEAKER

LARGE

SMALL × 2

REAR

SPEAKER

CENTER

SPEAKER

SMALL

USE

SUB

WOOFER

LFE MODE

LOW CUT FIL.

CROSS OVER

CENTER DELAY

REAR DELAY

–

+10dB

100Hz

EXIT

SPEAKER MODE

SOUND EDIT OPERATION (GUI OPERATION)

LEVEL AND BALANCE ADJUSTMENT

÷First, perform settings in the “SETTING THE SPEAKER MODE”.

(Refer to page 29.)

÷If you press the SOUND EDIT button on a function operation

display, display switches to “SOUND EDIT” indications for the

currently selected surround mode.

(When using PRO-LOGIC THEATER)

NOTE:

If you adjust the level to match a program source with little bass,

clipping may occur with a program source that has a lot of bass,

resulting in distortion from the sub-woofer. Pay careful attention

to sub-woofer channel output, making sure the level is not too

high.

EFFECT LEVEL

– +

÷Adjust surround effect level. (10 – 80)

÷Press

–

to reduce the surround effect, press

to increase it.

Press

EXIT

to return to the original function display.

7Adjustment using the TEST TONE

1. Press the TEST TONE button to switch ON.

÷The test tone is output from channels set in the “SETTING

THE SPEAKER MODE”.

2. Use the

, and

–

buttons to adjust channel

volume level balance.

÷Adjust so that the volume level of each channel is the same.

3. Press the TEST TONE button to switch OFF.

4. Press the EXIT button.

÷Adjust level and balance settings with the buttons.

÷In the “SETTING THE SPEAKER MODE”, parameters for

channels set to “NONE” cannot be adjusted.

Switches to the SPEAKER MODE display. (Refer

to page 29.)

This switches the test tone signal used for

adjustment ON/OFF. When ON, the test tone is

output through each channel in turn. The display

below the TEST TONE button indicates the

channel through which the test tone is being

output.

(Example) F-L : Front Left channel

MASTER BALANCE

L R

÷Adjust the system’s overall left/right volume level balance.

÷Press

and the right channel’s volume level decreases.

÷Press

and the left channel’s volume level decreases.

REAR BALANCE

L R

÷Adjust rear channel left/right volume level balance.

÷Press

and the right rear channel’s volume level decreases.

÷Press

and the left rear channel’s volume level decreases.

CENTER LEVEL

– +

÷Adjust center channel volume level. (±10 dB)

÷Press

–

to lower volume, press

to raise volume.

REAR LEVEL

– +

÷Adjust rear channel volume level. (±10 dB)

÷Press

–

to lower volume, press

to raise volume.

SUB WF LEVEL

– +

÷Adjust sub-woofer channel volume level. (±10 dB)

÷Press

–

to lower the volume, press

to raise volume.

SPEAKER

MODE

TEST

TONE

SPEAKER

MODE

TEST

TONE

CENTER LEVEL

REAR LEVEL

SUB WF LEVEL

EFFECT LEVEL

–

+10

–10

EXIT

SOUND EDIT

PRO-LOGIC THEATER

F - L

MASTER BALANCE

REAR BALANCE

REMOTE SET UP

VCR 1

0 1 2 3 4

5 6 7 8 9

POWER

CH＋

CH−

TV/

VCR

FUNC

MTS

CLEAR

R C A

SHARP

ZENITH

S O N Y

TOSHIBA

HITACHI

J V C

PANASONIC

EXIT

REMOTE SET UP (GUI OPERATION)

Even if your audio/video components are not made by Pioneer,

performing the following procedures will enable you to operate

them with this unit’s remote control and GUI. (If you do not

perform the following procedures, you will not be able to

operate other manufacturers’ components with this unit’s remote

control.)

When operating, be sure to connect an IR repeater (page 10).

Calling up and setting up presets

This unit is already preset with the remote control signals of

other manufacturers’ components. The following procedures

show you how to call up and set up these presets.

1. Press the SET UP button that is indicated on all the function

operation displays.

Display switches to the SET UP MENU.

4. The selected manufacturers’ name and preset operation

buttons are indicated in black.

This calls up the preset.

To finish remote set up operation, press the EXIT button.

NOTE:

To return preset buttons to their original settings, press the

CLEAR button. The original settings are Pioneer remote control

commands.

Even if a button is preset, it may not operate. If this happens,

learn the command using the learning function (page 32).

REMOTE SET UP

VCR 1

0 1 2 3 4

5 6 7 8 9

POWER

CH＋

CH−

TV/

VCR

FUNC

MTS

CLEAR

R C A

SHARP

ZENITH

S O N Y

TOSHIBA

HITACHI

J V C

PANASONIC

EXIT

3. Select the manufacturer of your component.

÷For VCRs, CD players and TVs, press the NEXT button and

another manufacturers’ list is displayed.

÷For TVs, there’s also a display of CATV terminal

manufacturers you can select from. (However, if you select

a CATV manufacturer, a TV cannot be operated. In this case,

learn the TV operation signals, see page 32.)

SET UP MENU

ONE TOUCH

OPERATION SET UP

L D C D

REMOTE SET UP

EXIT

VCR 1 VCR 2 TAPE 1

L D C D

VCR 1 VCR 2 TAPE 1 T V

2. Select one of the six REMOTE SET UP functions.

The display switches to REMOTE SET UP indications. The

name of preset manufacturers are indicated in white in the

lower half of the screen.

(Example: VCR)

REMOTE SET UP (GUI OPERATION)

÷If “OK” is displayed, learning has been completed. If you want

to use another button for learning, repeat steps 2 and 3.

NOTE:

To return the buttons you used for learning to their original

settings, press the CLEAR button. This returns them to the

original Pioneer remote control commands.

There are no signals in buttons

ΙΙ

, and

ΙΙΙ

, so you can use

them for learning.

Even when “OK” is displayed during learning, operation may

still not be possible. If this happens, repeat the learning

procedures. With some manufacturers’ components, learning

may be difficult to perform. Learning may also not be possible

if the remote control’s batteries are run down. If this is the

case, load the remote control with new batteries and repeat

the learning procedures.

Even black preset buttons can be used for learning other

commands.

Learning a command may not be possible if many commands

requiring a large amount of memory have already been learned

resulting in insufficient memory remaining.

3. Point your component’s remote control at this unit’s remote

sensor window and press the selected button.

− ＋

Press, holding the remote control

unit within 50 cm (20 inches) of

this unit’s sensor window.

VSX-D3S

÷If “NG” is displayed, repeat steps 2 and 3.

÷When you have completed learning, press the EXIT button.

REMOTE SET UP

VCR 1

0 1 2 3 4

5 6 7 8 9

POWER

CH＋

CH−

TV/

VCR

FUNC

MTS

CLEAR

R C A

SHARP

ZENITH

S O N Y

TOSHIBA

HITACHI

J V C

PANASONIC

EXIT

STANDBY

Learning

Pioneer remote control commands are in the non-preset gray

buttons, but you can use them to learn remote control signals from

your component’s remote control.

1. Perform the first three steps of “Calling up and setting up

presets”.

2. Select the gray button you want to use for learning and

press.

The “STANDBY” indication flashes. (If you remain in STANDBY

for about 1 minute, it is canceled.)

(Example: Using the 0 button for learning)

REMOTE SET UP

VCR 1

POWER

CH＋

CH−

TV/

VCR

FUNC

MTS

CLEAR

R C A

SHARP

ZENITH

S O N Y

TOSHIBA

HITACHI

J V C

PANASONIC

EXIT

0 1 2 3 4

5 6 7 8 9

ONE TOUCH OPERATION SET UP (GUI OPERATION)

÷Sets the operation signal that is transmitted when a remote

control ONE TOUCH OPERATION button is pressed.

÷Initially, Pioneer remote control signals are transmitted.

(Figure 1)

(Figure 1: Initial settings for LD)

To operate other manufacturers’ components, first complete

REMOTE SET UP procedures (page 31).

Example : When you want to change LD ONE TOUCH

OPERATION commands.

1. Press the SET UP button for display of the operation buttons

of each function.

The SET UP MENU is displayed.

2. Select LD from the five ONE TOUCH OPERATION SET UP

function buttons.

ONE TOUCH OPERATION SET UP indications are displayed.

(Example: LD)

LD TUNER

VCR 1

VCR 2 TAPE

Press the

LD button.

1~ 4

:You can select which operation buttons will transmit operation

signals and those which will not.

When the operation button’s character is black, a signal will be

transmitted. If it is gray, it will not be transmitted. The button’s

character color changes each time it is pressed.

÷With other manufacturers’ components, if power is on when the

POWER signal is transmitted, power is switched off.

When the TV “FUNC” signal is transmitted, the TV function may

not become the function connected to the receiver.

For this reason, when other manufacturers’ presets are called up

with REMOTE SET UP, commands are not automatically

transmitted.

5, 6

:TV and LD manufacturers settings are displayed.

÷If you use REMOTE SET UP (page 31) to call up another

manufacturers’ presets, that manufacturers’ name is displayed.

÷When you use the REMOTE SET UP learning function (page

32), the “PIONEER” indication becomes gray. Remote control

signals set with REMOTE SET UP are transmitted.

To return to the original Pioneer remote control commands,

press the ON/OFF button (on the left of “PIONEER”) to turn the

“PIONEER” indication black.

(If they are not the original Pioneer remote control commands,

even Pioneer components may switch OFF when the POWER

command is transmitted, or there may be some other incorrect

operation.)

3. After completing the settings, press the EXIT button.

NOTE:

With original Pioneer remote control commands, the TV function

always becomes “LD”, so connect the receiver’s VIDEO OUT

(TO MONITOR TV) terminal to the TV’s LD video input terminal.

The transmitted signal is .....

manufacturer ..... PIONEER

TV .................. POWER ON

TV ...................... FUNC. LD

LD .................. POWER ON

LD ............................. PLAY

SET UP MENU

ONE TOUCH

OPERATION SET UP

L D C D

REMOTE SET UP

EXIT

VCR 1 VCR 2 TAPE 1

L D C D

VCR 1 VCR 2 TAPE 1 T V

ONE TOUCH

OPERATION SET UP

FUNC

EXIT

LD LD

LD PIONEER

POWER POWER

PIONEER

1 2 3 4

TROUBLESHOOTING

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component,

check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical

appliances being used.

If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest PIONEER authorized service center or

your dealer to carry out repair work.

Symptom

Power does not come on even

when the POWER switch is

pressed.

Control is not possible

regardless of what operation

button is pressed.

No sound is produced, even

when the input selector button

is selected.

No picture is produced, even

when the input selector button

is selected.

High noise level.

Remedy

÷Connect cord securely.

÷Unplug the power cord of the unit from the AC

wall outlet, then plug it in again.

÷Unplug the power cord of the unit from the AC

wall outlet, then plug it in again.

÷Press the RESET button.

÷If static electricity is pronounced, it is

recommended that you operate the unit using

the remote control unit.

÷Consult pages 6 — 10 and perform connections

correctly.

÷Press the MUTE button to cancel the MUTING

effect.

÷Raise volume.

÷Connect wires to terminals securely.

÷Connect input cords securely.

÷Press the button again to the OFF position.

÷Switch the SPEAKERS button ON.

÷Consult pages 6 — 10 and perform connections

correctly.

÷Press the correct button.

÷Tune the station in correctly.

÷Connect the antenna securely.

÷Stretch both ends of antenna taut and locate

direction yielding optimum reception.

÷Replace accessory FM antenna with an outdoor

FM antenna.

÷Change the direction of the AM loop antenna and

find a position where reception is improved.

÷Erect an outdoor AM antenna or connect a ground

wire.

÷Turn off the appliances generating noise or

remove them from the vicinity of the stereo

equipment.

÷Separate the antenna from the unit by some

distance.

Cause

÷Power cord is disconnected.

÷Instances are rare, but the problem may be

due to the operation of the protector circuit.

÷Static electricity affects the unit when the air

is dry, such as in winter.

÷Connections are incorrect.

÷The MUTE button is pressed.

÷VOLUME is turned down.

÷Speaker connecting wires are disconnected

from speaker terminals.

÷One or both of the input cords are

disconnected.

÷TAPE 2 MONITOR button is in the ON position.

÷The SPEAKERS button is OFF.

÷Connections are incorrect.

÷The selected input selector button is not

correct.

÷Station has not been tuned in to correct

frequency.

÷Antenna has not been connected or has

become disconnected.

FM reception

÷Accessory FM antenna remains bundled up

or it is not pointing in the right direction.

÷Weak broadcasting station signals.

AM reception

÷AM loop antenna is not pointing in the right

direction.

÷Weak broadcasting station signals.

÷Noise is being picked up by this unit from

other equipment (especially electrical

appliances using motors or fluorescent

lights).

TROUBLESHOOTING

Symptom

No auto stop.

TV source cannot be seen when

the VCR’s TV tuner is used.

No rear sound is produced.

Remote control does not work.

Cause

÷Input signals are not strong enough.

÷TV antenna is not connected to the VCR, or

connections are faulty.

÷The VCR’s input switch is set to line input.

÷The SPEAKER MODE is set incorrectly.

÷The REAR LEVEL is turned down.

÷Speaker connecting wires are disconnected

from the REAR SPEAKERS terminals.

÷Batteries are dead or missing in remote

control unit.

÷Poor angle or too great a distance from the

remote sensor window.

÷There is an obstacle between you and the

remote sensor window.

÷A fluorescent light is shining on the remote

sensor window.

÷The Main-repeater signal does not reach

other components.

Remedy

÷(FM) If the supplied simple antenna is being

used, change to an outdoor antenna.

÷Consult the VCR’s operating instructions, and

connect the antenna correctly.

÷Set the VCR’s input switch to built-in tuner.

÷Set correctly.

÷Refer to page 30 and adjust the rear level.

÷Connect wires to the terminals securely.

÷Insert new batteries.

÷Use within 7 meters and within a 30 degree angle

of the remote sensor window.

÷Change your position or move the obstacle.

÷Move the receiver so fluorescent light does not

shine directly on the receiver’s front panel remote

sensor window.

÷Try changing the position of this unit or other

units. If the signal still does not reach other

components, use a supplied Mini-repeater.

Abnormal functioning of this unit may be caused by static electricity or other external interference. To restore normal operation, turn

the power off and then on again, or unplug the AC power cord and then plug it in again.

APPENDIX A: SPECIFICATIONS

Amplifier Section

<2-channel mode>

Continuous average power output of 130 watts* per

channel, min., at 8 ohms, from 20 Hz to 20,000 Hz with

no more than 0.05 %** total harmonic distortion.

<5-channel mode>

Continuous average power output of 100 watts* per

channel, min., at 8 ohms, from 20 Hz to 20,000 Hz with

no more than 0.8 %** total harmonic distortion.

*Measured pursuant to the Federal Trade Commission’s Trade

Regulation rule on Power Output Claims for Amplifiers.

** Measured by Audio Spectrum Analyzer.

Continuous Power Output

Front ...................................... 100 W + 100 W (1 kHz, 0.8 %, 8 Ω)

Center ................................................. 100 W (1 kHz, 0.8 %, 8 Ω)

Rear ....................................... 100 W + 100 W (1 kHz, 0.8 %, 8 Ω)

[Multi-voltage model]

Continuous Power Output (DIN)

Front (1 kHz, T.H.D. 1 %, 8 Ω)............................. 150 W + 150 W

Dynamic Power (2 Ω/4 Ω)........................................ 275 W/220 W

Input (Sensitivity/Impedance)

PHONO MM ........................................................... 2.8 mV/47 kΩ

CD, TAPE 1, TAPE 2, LD,

VCR 1, VCR 2, VIDEO, TV/SAT ............................. 200 mV/47 kΩ

Phono Overload Level (T.H.D. 0.1%, 1 kHz)

PHONO MM ...................................................................... 80 mV

Frequency Response

PHONO MM ..................................... 20 Hz to 20,000 Hz ±0.3 dB

CD, TAPE 1, TAPE 2, LD, VCR 1,

VCR 2, VIDEO, TV/SAT ......................... 5 Hz to 100,000 Hz

–3

Output (Level/Impedance)

TAPE 1 REC, TAPE 2 REC .................................... 200 mV/2.2 kΩ

VCR 1 OUT, VCR 2 OUT ...................................... 200 mV/2.2 kΩ

Tone Control

BASS .................................................................... ±8 dB (150 Hz)

TREBLE ................................................................ ±8 dB (10 kHz)

SUPER BASS .................................... 0 ~ +8 dB (80 Hz, variable)

Signal-to-Noise Ratio (IHF, short circuited, A network)

PHONO MM ........................................................................ 76 dB

CD, TAPE 1, TAPE 2, LD,

VCR 1, VCR 2, VIDEO, TV/SAT ........................................... 98 dB

Signal-to-Noise Ratio [EIA, at 1 W (1 kHz)]

PHONO MM ........................................................................ 77 dB

CD, TAPE 1, TAPE 2, LD,

VCR 1, VCR 2, VIDEO, TV/SAT ........................................... 80 dB

VIDEO Section

Input (Sensitivity/Impedance)

VCR 1, VCR 2, LD, VIDEO, TV/SAT ........................... 1 Vp-p/75 Ω

Output (Level/Impedance)

VCR 1, VCR 2, MONITOR ......................................... 1 Vp-p/75 Ω

Frequency Response

VCR 1, VCR 2,

LD, VIDEO = MONITOR ............................ 5 Hz to 10 MHz

–3

Signal-to-Noise Ratio............................................................ 55 dB

Cross Talk .............................................................................. 55 dB

AC-3 Input Section

AC-3 • RF (LD) ................................................................................ 1

AC-3 • DIGITAL (TV/SAT) .............................................................. 1

FM Tuner Section

Frequency Range ........................................ 87.5 MHz to 108 MHz

Usable Sensitivity ................... Mono: 11.2 dBf, IHF (1.0 µV/75 Ω)

50 dB Quieting Sensitivity .................................... Mono: 16.8 dBf

Stereo: 38.6 dBf

Signal-to-Noise Ratio.............................. Mono: 80 dB (at 65 dBf)

Stereo: 76 dB (at 85 dBf)

Distortion ...................................................... Stereo: 0.3 % (1 kHz)

Alternate Channel Selectivity ............................... 65 dB (400 kHz)

Stereo Separation ..................................................... 45 dB (1 kHz)

Frequency Response ............................... 30 Hz to 15 kHz (

+0.5

–2.0

) dB

Antenna Input ...................................................... 300 Ω balanced

75 Ω unbalanced

AM Tuner Section

Frequency Range ..................... 531 kHz to 1,602 kHz (9 kHz step)

530 kHz to 1,700 kHz (10 kHz step)

Sensitivity (IHF, Loop antenna) ..................................... 300 µV/m

Selectivity .............................................................................. 25 dB

Signal-to-Noise Ratio............................................................ 50 dB

Antenna ................................................................... Loop antenna

Miscellaneous

Power Requirements

U.S. and Canadian models ............................... AC 120 V, 60 Hz

Multi-voltage model ............... AC 110 V/120-127 V/220 V/240 V

(Switchable), 50/60 Hz

Power Consumption

U.S. and Canadian models ................................. 455 W, 700 VA

Multi-voltage model ........................................................ 1175 W

In Standby Condition ............................................................... 5 W

AC Outlets

U.S. and Canadian models

SWITCHED x 2 .............................. TOTAL 100 W (0.8 A) MAX

UNSWITCHED x 1 ..................................... 100 W (0.8 A) MAX

Multi-voltage model

SWITCHED x 2 .......................................... TOTAL 100 W MAX

UNSWITCHED x 1 ................................................. 100 W MAX

Dimensions ................................ 420 (W) x 162 (H) x 425 (D) mm

16-9/16 (W) x 6-3/8 (H) x 16-3/4 (D) in

Weight (without package)

U.S. and Canadian models .......................... 15.0 kg (33 lb 1 oz)

Multi-voltage model ..................................... 15.2 kg (33 lb 8 oz)

Furnished Parts

FM T-type Antenna ...................................................................... 1

AM Loop Antenna........................................................................ 1

Dry Cell Batteries (size “AA” IEC R6P) ........................................ 2

Remote Control Unit .................................................................... 1

Main-Repeater ............................................................................. 1

Mini-Repeater .............................................................................. 1

Operating Instructions ................................................................. 1

NOTE:

Specifications and the design are subject to possible

modifications without notice, due to improvements.

APPENDIX B: SURROUND EFFECT

This unit has a built-in surround processor for adding presence

and an expansive effect to the sound.

5 Mode Selection with DSP (Digital Signal Processor):

JAZZ:

This gives you the sound field of a jazz club.

DANCE:

A “hot” high-energy sound, with extra reverb for greater

ambience.

SIMULATED SURROUND:

The “SIMULATED SURROUND” creates the effects of

reverberated and reflected sound from the walls and ceiling

similar to a concert hall. These sound-effects added to the actual

sound from the source make you feel as if you were in a more

expanded space. The different ranges of the expanded space

can be set by the REAR DELAY TIME button.

The “SIMULATED SURROUND” also gives effects on monaural

sources by outputting the added reverberated sound from the

rear speakers while outputting the actual source sound from the

front speakers. Turn on the “SIMULATED SURROUND” for a

monaural source to gain effective surround playback.

HALL:

You can enjoy a convincing hall sound.

THEATER:

This gives you the sound field of an atmosphere of a movie

theater.

÷You can use these five modes in combination with AC-3 and

PRO-LOGIC.

DOLBY PRO-LOGIC SURROUND:

Choose this setting for movies and music (especially Video

Discs and video tapes bearing the

DOLBY SURROUND

mark)

playback.

DOLBY PRO-LOGIC SURROUND continuously detects the size

and direction of the dominant signal and cancels undesirable

crosstalk, thereby providing signal emphasis.

It makes you clearly perceive the directional source of the

music. Real flow of sound also can be re-created naturally using

this feature. You can feel as if being in an outstanding and

expansive sound field.

Even if the video recordings do not bear the

DOLBY SURROUND

mark, some of them may be Dolby Surround encoded.

Choose the SIMULATED SURROUND mode if the source sound

signal is mono. Little or no sound will be heard from the

surround speakers if the DOLBY PRO-LOGIC SURROUND mode

is selected.

DOLBY 3CH LOGIC:

Select “NONE” with the SPEAKER MODE REAR SPEAKER button,

press the DOLBY PRO-LOGIC button ON and DOLBY 3CH LOGIC

is selected.

Combining the rear speaker signal with that of the front speakers

results in your being able to enjoy a regenerated sound field

which has comparatively more presence and a more expansive

feeling from the front 3 channels (front L, front R, and center

speakers) than that of ordinary stereo regeneration. DOLBY 3CH

LOGIC can be used with stereo sources not encoded with

DOLBY SURROUND.

DOLBY AC-3:

Choose this setting for movies and music (especially video

discs bearing the

AC–3 D I G I T A L

DOLBY SURROUND

mark) playback. The

LaserDisc player’s AC-3 RF OUT jack must be connected to

this unit’s AC-3 RF IN jack.

AC-3 is the compression format used when recording 6-channel

audio onto the digital track of film for the SR D (Surround

Digital) movie theater surround system. To enable AC-3 to

reproduce the same multi-track audio in the home on laserdisc,

the six independent audio channels compressed by the AC-3

system are recorded on the right analog stereo channel. Among

these six channels, the sub-woofer signal (SW) is exclusively for

low-range reproduction. Since this SW signal is not really

necessary as far as the total system is concerned, the number of

channels is expressed as 5.1.

APPENDIX C: DOLBY AC-3 SURROUND

Dolby Laboratories spearheaded home theater with the introduction of Dolby Surround, and then defined it with the follow-up format

Dolby Pro-Logic Surround. They have continued the evolution of home theater with the introduction of Dolby AC-3 Pro-Logic, a Multi-

Channel Digital delivery system. Just as Dolby Surround found it’s beginnings in the cinema, so does AC-3. This advanced multi-channel

digital sound, although originally conceived for and later chosen for HDTV, made it practical to implement in the cinema because it

enabled the film to retain the analog soundtrack. With backwards compatibility a priority so the film could be played in any cinema, it

was decided to place the new digital optical track between the sprocket holes, which was a key factor in defining its maximum practical

bit rate (see illustration).

In 1992 Dolby Surround Digital, the film sound format with AC-3 as its keystone, made its debut in the cinema. In less than three years,

more than 300 feature films had been released in this new format, and nearly 1,500 cinemas had been equipped for playback of the digital

soundtrack. Furthermore, AC-3 can now be brought to the consumer’s home today via the LaserDisc.

Traditional Pulse Code Modulation (PCM), which is utilized on compact discs and LD’s 4-channel matrixed digital audio tracks, uses a

16-bit word to “describe” the sampled point in the original analog wave. By sampling this analog wave 44,100 times per second for each

channel, the system will yield a dynamic range of 96 dB from the loudest sound to the noise floor. However, this process creates an

immense amount of data which is too large for multi-channel systems. Thus, a form of data reduction must be employed to reduce the

total amount of information without serious degradation of the sound quality — hence the introduction of AC-3.

The premise of AC-3 is simple, it reproduces the full bit resolution (16-bit) when a lower resolution will not result in the same sound

quality. However, when a lower resolution is acceptable, it will utilize this lower resolution opting instead for psychoacoustical theories

and digital noise filtering technologies to help insure acceptable sound quality.

AC-3

ENCODING

5.1 – Channel

Digital Soundtrack 4 – Channel Analog

Soundtrack (Matrixed)

AC-3 IN THE CINEMA

APPENDIX C: DOLBY AC-3 SURROUND

THE LASER DISC FORMAT

The one major concern when the idea of incluiding another form of audio on a laser disc was .... Backwards Compatibility. It would not

do the laser disc format any justice, especially in a time of growing acceptability, to change the audio system without considering those

consumers that had already purchased a laser disc player. Thus to maintain backward compatibility, the AC-3 encoding was deemed

to be stored in one of the existing analog tracks.

The above diagram shows the format of the AC-3 Pro-Logic laser disc. The PCM audio track, containing the 4-channel matrixed digital

soundtrack, was fully maintained for continued use in laser disc players with digital capabilities. As mentioned above, one of the analog

channels will now contain the AC-3 encoding, while the other analog channel will contain a mono analog soundtrack, which still provides

backwards compatibility with those pre-1984 laser disc players (1984 was the year we introduced an LD player with digital capabilities).

THE ADVANTAGES OF AC-3 OVER PRO-LOGIC

AC-3 is called a 5.1-channel system because it provides 5 independent channels (left, right, center, left surround, and right surround),

all reproducing a 20 – 20,000 Hz range. In addition, the system provides for an independent sub-woofer channel, which is called a low

frequency effects channel. Use of the low frequency effect channel is optional, since the 5 channels provide a full frequency bandwidth,

but available for those consumer wishing to include a sub-woofer for thunderous bass reproduction. Furthermore, AC-3 provides

improved channels separation, multi-directional discrete capability, and increased sound-design creative flexibility (for the movie

makers). Below highlights some of the other advantages of Dolby AC-3:

Available Channels on Disc

Playback Channels

Description of Playback Channels

Sound Processing

Surround Channel Maximum

Frequency Response

Other Information

DOLBY SURROUND DIGITAL (AC-3)

5.1 Channels

Left, Right, Center, Left Surround, Right

Surround, and Sub-woofer

Discrete Digital AC-3

Encoding & Decoding

20,000 Hz

-5 Discrete Channels

-Fully Backward Compatible with

Dolby Surround

-High Dynamic Range

-Extremely Accurate and Natural

Sound for Vocals and Effects Imaging

DOLBY SURROUND PRO-LOGIC

2 channels

4 channels

Left, Right, Center, and Surround

Analog Matrix Processing for Dolby Surround

7,000 Hz

2 4 6 8 10 12 14 MHz

Digital (PCM)

Audio

Dolby AC-3

Digital Audio

Analog Mono

Audio

Analog Video

Dolby AC-3

Digital Audio

Analog Mono

Audio

Digital (PCM)

Audio

Analog Video

<95E00FF0H01> Printed in Japan <ARB7050-C>

Published by Pioneer Electronic Corporation.

All ri

hts reserved.

MAINTENANCE OF EXTERNAL SURFACES

÷Use a polishing cloth or dry cloth to wipe off dust and dirt.

÷When the surfaces are dirty, wipe with a soft cloth dipped

in some neutral cleanser diluted five or six times with

water, and wrung out well, and then wipe again with a dry

cloth. Do not use furniture wax or cleaners.

÷Never use thinners, benzine, insecticide sprays or other

chemicals on or near this unit, since these will corrode the

surfaces.

Selecting fine audio equipment such as the unit you’ve just

purchased is only the start of your musical enjoyment. Now it’s

time to consider how you can maximize the fun and excitement

your equipment offers. This manufacturer and the Electronic

Industries Association’s Consumer Electronics Group want you

to get the most out of your equipment by playing it at a safe

level. One that lets the sound come through loud and clear

without annoying blaring or distortion—and, most importantly,

without affecting your sensitive hearing.

Sound can be deceiving. Over time your hearing “comfort

level” adapts to higher volumes of sound. So what sounds

“normal” can actually be loud and harmful to your hearing.

Guard against this by setting your equipment at a safe level

BEFORE your hearing adapts.

To establish a safe level:

÷Start your volume control at a low setting.

÷Slowly increase the sound until you can hear it comfortably

and clearly, and without distortion.

Once you have established a comfortable sound level:

÷Set the dial and leave it there.

Taking a minute to do this now will help to prevent hearing

damage or loss in the future. After all, we want you listening for

a lifetime.

Want You

LISTENING

For A Lifetime

We Want You Listening For A Lifetime

Used wisely, your new sound equipment will provide a

lifetime of fun and enjoyment. Since hearing damage from loud

noise is often undetectable until it is too late, this manufacturer

and the Electronic Industries Association’s Consumer Electronics

Group recommend you avoid prolonged exposure to excessive

noise. This list of sound levels is included for your protection.

Decibel

Level Example

30 Quiet library, soft whispers

40 Living room, refrigerator, bedroom away from traffic

50 Light traffic, normal conversation, quiet office

60 Air conditioner at 20 feet, sewing machine

70 Vacuum cleaner, hair dryer, noisy restaurant

80 Average city traffic, garbage disposals, alarm clock

at two feet.

THE FOLLOWING NOISES CAN BE DANGEROUS

UNDER CONSTANT EXPOSURE

90 Subway, motorcycle, truck traffic, lawn mower

100 Garbage truck, chain saw, pneumatic drill

120 Rock band concert in front of speakers, thunderclap

140 Gunshot blast, jet plane

180 Rocket launching pad

Information courtesy of the Deafness Research Foundation.

Want You

LISTENING

For A Lifetime

EST 1924

EIA

•

EST 1924

EIA

•

PIONEER ELECTRONIC CORPORATION

4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153, Japan

PIONEER ELECTRONICS [USA] INC.

P.O. BOX 1540, Long Beach, California 90801-1540

PIONEER ELECTRONICS OF CANADA, INC.

300 Allstate Parkway, Markham, Ontario L3R 0P2, Canada

PIONEER ELECTRONIC [EUROPE] N.V.

Haven 1087 Keetberglaan 1, 9120 Melsele, Belgium, TEL: 03/570.05.11

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: [03] 580-9911

PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.

Augusto Rodin No. 128 PB Col. San Juan Mixcoac Mexico D.F. CP.03730 TEL: 52-5-598-3950

Pioneer Audio Video Stereo Receiver Vsx D3S Users Manual ARB7050C

VSX-D3S to the manual 027eb5eb-e67f-45d9-81ba-df907198bf9b

Navigation menu

Versions of this User Manual:

Views

Navigation