Pioneer Vsx 44 Owners Manual

2014-08-26

: Pioneer Pioneer-Vsx-44-Owners-Manual pioneer-vsx-44-owners-manual pioneer pdf

Open the PDF directly: View PDF .
Page Count: 68

http://www.pioneerelectronics.com (US)

http://www.pioneerelectronics.ca (Canada)

•

Protect your new investment

The details of your purchase will be on file for reference in the event of an insurance claim such as loss or theft.

•

Improve product development

Your input helps us continue to design products that meet your needs.

•

Receive a free Pioneer newsletter

Registered customers can opt in to receive a monthly newsletter.

•

Receive free tips, updates and service bulletins on your new product

AV Receiver

VSX-44

Operating Instructions

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

D3-4-2-1-1b_A1_En

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

— Consult the dealer or an experienced radio/TV technician for help.

D8-10-1-2_A1_En

Information to User

Alterations or modifications carried out without appropriate authorization may invalidate the user’s right to operate

the equipment.

D8-10-2_A1_En

WARNING

This equipment is not waterproof. To prevent a fire or

shock hazard, do not place any container filled with

liquid near this equipment (such as a vase or flower

pot) or expose it to dripping, splashing, rain or

moisture.

D3-4-2-1-3_A1_En

WARNING

To prevent a fire hazard, do not place any naked flame

sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A1_En

VENTILATION CAUTION

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat radiation (at

least 40 cm at top, 20 cm at rear, and 20 cm at each side).

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the product,

and to protect it from overheating. To prevent fire hazard,

the openings should never be blocked or covered with

items (such as newspapers, table-cloths, curtains) or by

operating the equipment on thick carpet or a bed.

D3-4-2-1-7b*_A1_En

Caution

To prevent fire hazard, the Class 2 Wiring Cable

should be used for connection with speaker, and

should be routed away from hazards to avoid damage

to the insulation of the cable.

D3-7-13-67*_A1_En

Operating Environment

Operating environment temperature and humidity:

+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in

locations exposed to high humidity or direct sunlight (or

strong artificial light).

D3-4-2-1-7c*_A2_En

These symbols are only valid

in the European Union.

K058c_A1_En

(Symbol examples for batteries)

WARNING

Store small parts out of the reach of children and

infants. If accidentally swallowed, contact a doctor

immediately.

D41-6-4_A1_En

This product is for general household purposes. Any

failure due to use for other than household purposes

(such as long-term use for business purposes in a

restaurant or use in a car or ship) and which requires

repair will be charged for even during the warranty

period.

K041_A1_En

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in

accordance with the manufacturer’s

instructions.

Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce

heat.

Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two

blades with one wider than the other. A

grounding type plug has two blades and a third

grounding prong. The wide blade or the third

prong are provided for your safety. If the provided

plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the point where they exit from

the apparatus.

10)

Only use attachments/accessories specified by

the manufacturer.

Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with

the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to

avoid injury from tip-over.

Unplug this apparatus during lightning storms

or when unused for long periods of time.

Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has

been damaged in any way, such as power-supply

cord or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture,

does not operate normally, or has been dropped.

D3-7-13-69_En

11)

12)

13)

14)

CAUTION

The STANDBY/ON switch on this unit will not

completely shut off all power from the AC outlet.

Since the power cord serves as the main disconnect

device for the unit, you will need to unplug it from the

AC outlet to shut down all power. Therefore, make

sure the unit has been installed so that the power

cord can be easily unplugged from the AC outlet in

case of an accident. To avoid fire hazard, the power

cord should also be unplugged from the AC outlet

when left unused for a long period of time (for

example, when on vacation).

D3-4-2-2-2a*_A1_En

CAUTION

This product satisfies FCC regulations when shielded

cables and connectors are used to connect the unit

to other equipment. To prevent electromagnetic

interference with electric appliances such as radios

and televisions, use shielded cables and connectors

for connections.

D8-10-3a_A1_En

IMPORTANT NOTICE

THE MODEL NUMBER AND SERIAL NUMBER OF

THIS EQUIPMENT ARE ON THE REAR OR BOTTOM.

RECORD THESE NUMBERS ON YOUR ENCLOSED

WARRANTY CARD AND KEEP IN A SAFE PLACE

FOR FUTURE REFERENCE.

D36-AP9-1_A1_En

WARNING: Handling the cord on this product or

cords associated with accessories sold with the

product may expose you to chemicals listed on

proposition 65 known to the State of California and

other governmental entities to cause cancer and

birth defect or other reproductive harm.

D36-P5_B1_En

Thank you for buying this Pioneer product. Please read

through these operating instructions so you will know how to

operate your model properly.

Features

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Before you start

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Checking what’s in the box. . . . . . . . . . . . . . . . . . . . . . . . . 8

Installing the receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Flow of settings on the receiver

. . . . . . . . . . . . . . . 8

01 Controls and displays

Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Loading the batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Operating range of remote control . . . . . . . . . . . . . . . . 13

02 Connecting your equipment

Determining the speakers’ application . . . . . . . . . . . . . . . 14

Some tips for improving sound quality . . . . . . . . . . . . . 15

Connecting the speakers . . . . . . . . . . . . . . . . . . . . . . . . . 15

Connect the surround back or front height speakers. . . 16

Switching the speaker terminal . . . . . . . . . . . . . . . . . . . 18

Making cable connections . . . . . . . . . . . . . . . . . . . . . . . . 18

HDMI cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

About HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Analog audio cables . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Digital audio cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Video cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

About video outputs connection. . . . . . . . . . . . . . . . . . . . 19

Connecting a TV and playback components . . . . . . . . . . . 20

Connecting using HDMI . . . . . . . . . . . . . . . . . . . . . . . . 20

Connecting your TV with no HDMI input . . . . . . . . . . . . 21

Connecting optional Bluetooth® ADAPTER . . . . . . . . . . . 22

Connecting to the network through LAN interface . . . . . . 22

Connecting to a wireless LAN. . . . . . . . . . . . . . . . . . . . . . 22

Connecting antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Using external antennas . . . . . . . . . . . . . . . . . . . . . . . . 23

Connecting an IR receiver . . . . . . . . . . . . . . . . . . . . . . . . 24

Switching components on and off using the

12 volt trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Connecting an iPod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Connecting a USB device. . . . . . . . . . . . . . . . . . . . . . . . . 25

Connecting a MHL-compatible device . . . . . . . . . . . . . . . 25

Enjoy Roku video streaming service. . . . . . . . . . . . . . . . 25

Connecting an HDMI-equipped component to the front

panel input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Plugging in the receiver . . . . . . . . . . . . . . . . . . . . . . . . . . 26

03 Basic Setup

Automatically setting up for surround sound (MCACC) . . 27

Other problems when using the Auto MCACC setup . . . 28

04 Basic playback

Playing a source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Selecting the audio input signal . . . . . . . . . . . . . . . . . . 29

Playing an iPod. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Playing back files stored on an iPod . . . . . . . . . . . . . . . 31

Basic playback controls. . . . . . . . . . . . . . . . . . . . . . . . . 31

Switches between the iPod controls and the receiver

controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Playing a USB device . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Playing back audio files stored on a USB memory

device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Playing back photo files stored on a USB memory

device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

About playable file formats . . . . . . . . . . . . . . . . . . . . . . 32

Playing a MHL-compatible device. . . . . . . . . . . . . . . . . . . 33

Enjoy Roku video streaming service. . . . . . . . . . . . . . . . 33

Bluetooth® ADAPTER for Wireless Enjoyment of

Music . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Wireless music play. . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Pairing the Bluetooth ADAPTER and Bluetooth wireless

technology device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Listening to Music Contents of Bluetooth wireless

technology device with Your System . . . . . . . . . . . . . . . 35

Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Improving FM sound . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Saving station presets . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Listening to station presets . . . . . . . . . . . . . . . . . . . . . . 36

Naming preset stations . . . . . . . . . . . . . . . . . . . . . . . . . 36

05 Listening to your system

Choosing the listening mode . . . . . . . . . . . . . . . . . . . . . . 37

Auto playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Listening in surround sound . . . . . . . . . . . . . . . . . . . . . 37

Using the Advanced surround . . . . . . . . . . . . . . . . . . . 38

Using Stream Direct . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Using the Sound Retriever . . . . . . . . . . . . . . . . . . . . . . . . 38

Listening with Acoustic Calibration EQ. . . . . . . . . . . . . . . 38

Using surround back channel processing. . . . . . . . . . . . . 38

Setting the Up Mix function . . . . . . . . . . . . . . . . . . . . . . . 39

Setting the Audio options . . . . . . . . . . . . . . . . . . . . . . . . . 39

06 Playback with NETWORK features

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

About playable DLNA network devices. . . . . . . . . . . . . . 42

Using AirPlay on iPod touch, iPhone, iPad, and

iTunes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

About the DHCP server function . . . . . . . . . . . . . . . . . . 42

Authorizing this receiver . . . . . . . . . . . . . . . . . . . . . . . . 42

About HTC Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Playback with Network functions . . . . . . . . . . . . . . . . . . . 43

Basic playback controls . . . . . . . . . . . . . . . . . . . . . . . . . 43

Listening to Internet radio stations. . . . . . . . . . . . . . . . . 44

Listening to Pandora Internet Radio. . . . . . . . . . . . . . . . 44

About the Spotify audio stream playback function . . . . . . 45

Preparations (1) Installing the Spotify application

on mobile devices and registering a Spotify Premium

account . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Preparations (2) Connecting this unit to the network . . . 45

In order to use the Spotify audio stream playback

function from the Spotify application . . . . . . . . . . . . . . . 45

Playing back audio files stored on components

on the network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Playing back your favorite songs . . . . . . . . . . . . . . . . . . 45

The Network Setup menu . . . . . . . . . . . . . . . . . . . . . . . . . 46

Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Firmware Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Network setting using Safari browser . . . . . . . . . . . . . . 48

Friendly Name setting using Safari browser. . . . . . . . . . 48

Firmware update using Safari browser. . . . . . . . . . . . . . 48

Factory Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

About network playback . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Content playable over a network . . . . . . . . . . . . . . . . . . 50

About playback behavior over a network . . . . . . . . . . . . 50

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

About playable file formats . . . . . . . . . . . . . . . . . . . . . . . . 51

07 Home Menu

Using the Home Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Manual speaker setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Speaker Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

X.Over . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Contents

Channel Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Speaker Distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

The Input Assign menu . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Analog Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Component Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

The Auto Power Down menu . . . . . . . . . . . . . . . . . . . . . . 56

The Network Standby menu . . . . . . . . . . . . . . . . . . . . . . . 56

The MHL Setup menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Auto Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Setup ROKU standby mode. . . . . . . . . . . . . . . . . . . . . . 56

The Speaker System setting . . . . . . . . . . . . . . . . . . . . . . . 57

The 12 V Trigger Setting . . . . . . . . . . . . . . . . . . . . . . . . . . 57

The OSD Setup menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

08 Using the MULTI-ZONE feature

MULTI-ZONE listening . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Making MULTI-ZONE connections . . . . . . . . . . . . . . . . 58

Using the MULTI-ZONE controls . . . . . . . . . . . . . . . . . . 58

09 Control with HDMI function

Making Control with HDMI connections. . . . . . . . . . . . . . 59

HDMI Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Before using synchronization . . . . . . . . . . . . . . . . . . . . . . 60

About synchronized operations . . . . . . . . . . . . . . . . . . . . 60

Cautions on the Control with HDMI function . . . . . . . . . . 60

10 Additional information

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

NETWORK feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Troubleshooting of wireless LAN . . . . . . . . . . . . . . . . . . 63

HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Important information regarding the HDMI

connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Windows 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

MHL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

HTC Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

About iPod/iPhone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Apple Lossless Audio Codec . . . . . . . . . . . . . . . . . . . . . . 65

About FLAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

About messages displayed when using network

functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Resetting the main unit . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Cleaning the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Audio

Easy setup using MCACC

The MCACC automatically creates the optimum acoustic environment by compensating for

differences in speaker size, level and distance, and equalizing response.

Phase Control

Phase Control effectively eliminates phase lag which makes the sound lack synchronization

and significantly improves the multi-channel sound without any extra operation.

Video

Ultra HD (with 4K/60p video support) - Pass-through -

Up to 4K/60p resolution images can be passed through and displayed as such. A separate

monitor supporting Ultra HD (4K video) is required.

HDMI (3D, Audio Return Channel)

6 in/1 out

A compatible component is required to use the above function.

Connectivity

Easy Network connection with the Wireless LAN converter

With the AS-WL300 wireless LAN converter, you can enjoy using a wireless LAN connection for

the AV receivers. The AS-WL300 works with power supply from the AV receiver’s dedicated USB

terminal, so no AC adapter is required.

Bluetooth

adapter ready

Using the Bluetooth ADAPTER (AS-BT100 or AS-BT200) lets you enjoy music files on an iPhone

or other Bluetooth wireless technology enabled device wirelessly.

MHL

™

(Mobile High-definition Link) - compatible device playback

An incorporates MHL 2 mobile device can be connected to enjoy 3D videos, Full-HD videos,

high quality multi-channel audio, and photos etc., with charge the battery on the receiver.

iPod Playback

Your iPod or iPhone can be connected to the receiver’s USB terminal to play the music files on

the iPod or iPhone. Also, the iPod or iPhone is charged when it is connected to the receiver.

Network

Roku Ready

This receiver is certified Roku Ready®. By just plug the Roku Streaming Stick™ into the MHL

port, you can enjoy the hottest movies, TV shows, music, games and more on your TV by

streaming it directly from the Internet.

Spotify Digital Music-Streaming Service ready

Spotify is a digital music-streaming service that gives you on-demand access to millions of

songs. This receiver is ready for the Connect from Spotify, which lets you select songs on your

Spotify app for listening on your audio system. For service availability in your country check

www.spotify.com.

Compatible with Windows 8.1

This receiver is compatible with Windows 8.1, letting you easily stream music from compatible

PCs on your home network.

Apple AirPlay

With AirPlay you can stream music from iTunes to this receiver and play it through your home

theater system. You can even use the receiver to view metadata including song titles, artist as

well as the album art on a connected display. You can easily enjoy your iTunes music in any

room in the house.

DLNA Certified (1.5)

This receiver is DLNA certified (1.5), enabled to work not only as a DMP (Digital Media Player)

for playing DMS (Digital Media Server) audio files, but also as a DMR (Digital Media Renderer)

to be remote controlled by a device such as a smartphone or PC.

Internet Radio

By connecting this receiver to the network via the LAN terminal, you can listen to internet radio

stations.

Features

Playback / Processing

High Resolution Music Playback

High resolution music files with resolutions of 96 kHz/24 bit to 192 kHz/24 bit can be played.

Playback of AIFF, Apple Lossless, WAV and FLAC files via the front USB port and network is

supported.

Gapless Playback

The silent section between tracks is skipped when playing music files, eliminating the

interruptions that usually occur when playing live or concert contents.

Dolby Pro Logic IIz compatible

Adding a pair of speakers above the front left and right speakers adds expressiveness in the

vertical direction to the previous horizontally-oriented sound field. The height channel

strengthens the sound field’s sense of three-dimensionality and air, producing presence and

expansion.

Advanced Sound Retriever

Advanced Sound Retriever restores the output of compressed audio - such as WMA, AAC and

MP3 - to the level of CD sound by creating new signals to restore the minor details left out

during the compression process.

Installation

iControlAV5 Remote Application

This is an application that allowing intuitive operation of many of the receiver’s functions.

This application is available on the App Store for iPhone, iPod touch and iPad.

And also, you can get it on Google Play for Android smartphones.

The application can be downloaded free of charge.

ZONE Ready

This receiver is equipped with the Multi-zone (ZONE2) function. Multi-Zone enables music

playback from different sources in two zones at the same time.

Energy Saving Design

This AV receiver has an ecological design. In addition to even lower power consumption in

standby, the receiver is equipped with an “eco mode” for low power consumption when playing

contents as well. Furthermore, the eco mode can easily be set with a dedicated button on the

remote control or the iControlAV5.

Features

Before you start

Checking what’s in the box

Please check that you’ve received the following supplied

accessories:

•

Setup microphone

•

Remote control

•

AAA size IEC R03 dry cell batteries (to confirm system

operation) x2

•

AM loop antenna

•

FM wire antenna

•

Warranty card

•

Quick start guide

•

Safety Brochure

•

SPEAKER CAUTION Sheet (English only)

•

These operating instructions (CD-ROM)

Installing the receiver

•

When installing this unit, make sure to put it on a level and

stable surface.

Don’t install it on the following places:

– on a color TV (the screen may distort)

– near a cassette deck (or close to a device that gives off a

magnetic field). This may interfere with the sound.

– in direct sunlight

– in damp or wet areas

– in extremely hot or cold areas

– in places where there is vibration or other movement

– in places that are very dusty

– in places that have hot fumes or oils (such as a kitchen)

Flow of settings on the receiver

The unit is a full-fledged AV receiver equipped with an

abundance of functions and terminals. It can be used easily

after following the procedure below to make the connections

and settings.

The colors of the steps indicate the following:

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Required setting item

Setting to be made as necessary

Connecting the speakers

Where you place the speakers will have a big effect on

the sound.

•

Determining the speakers’ application (page 14)

•

Connecting the speakers (page 15)

•

Switching the speaker terminal (page 18)



Connecting the components

For surround sound, you’ll want to hook up using a

digital connection from the Blu-ray Disc/DVD player to

the receiver.

•

About video outputs connection (page 19)

•

Connecting a TV and playback components (page 20)

•

Connecting antennas (page 23)

•

Plugging in the receiver (page 26)



Power On

Make sure you’ve set the video input on your TV to this

receiver. Check the manual that came with the TV if you

don’t know how to do this.



The Speaker System setting (page 57)

(Specify either using the surround back front height

Speaker Bi-amp ZONE 2 speaker.)

The Input Assign menu (page 55)

(When using connections other than the recommended

connections.)

HDMI Setup (page 59)

(When the connected TV supports the HDMI Audio Return

Channel function.)



Use the on-screen automatic MCACC setup to set up

your system

•

Automatically setting up for surround sound (MCACC)

(page 27)



Basic playback (page 29)

•

Selecting the audio input signal (page 29)

•

Playing an iPod (page 31)

•

Switches between the iPod controls and the receiver

controls (page 31)

•

Choosing the listening mode (page 37)



Adjusting the sound as desired

•

Using the Sound Retriever (page 38)

•

Listening with Acoustic Calibration EQ (page 38)

•

Using surround back channel processing (page 38)

•

Setting the Up Mix function (page 39)

•

Setting the Audio options (page 39)

•

Manual speaker setup (page 53)

Chapter

Controls and displays

Front panel

INPUT SELECTOR

dial

Selects an input source (page 29).

SPEAKERS

See Switching the speaker terminal on page 18.

The Speaker System setting may or may not be displayed,

depending on the input source you have selected.

MCACC indicator

Lights when Acoustic Calibration EQ (page 38) is on (Acoustic

Calibration EQ is automatically set to on after the Auto

MCACC setup (page 27)).

ZONE controls

If you’ve made MULTI-ZONE connections (see Making MULTI-

ZONE connections on page 58) use these controls to control

the sub zone from the main zone (see Using the MULTI-ZONE

controls on page 58).

The Input format may or may not be displayed, depending

on the input source you have selected.

Character display

See Display on page 10.

Tuner control buttons

BAND

– Switches between AM, FM ST (stereo) and FM

MONO radio bands (page 36).

TUNER EDIT

– Use with

TUNE

/

PRESET

/-

and

ENTER

to memorize and name stations for recall

(page 36).

TUNE

/

– Used to find radio frequencies (page 36).

PRESET

/-

– Use to select preset radio stations

(page 36).

HDMI indicator

Blinks when connecting an HDMI-equipped component;

lights when the component is connected (page 20).

iPod iPhone indicator

Lights when an iPod/iPhone is connected and iPod/USB

input is selected (page 31).

Remote sensor

Receives the signals from the remote control (see Operating

range of remote control on page 13).

MASTER VOLUME

dial



STANDBY/ON

PHONES jack

Use to connect headphones. When the headphones are

connected, there is no sound output from the speakers. The

listening mode when the sound is heard from the headphone

can be selected only from PHONES SURR, STEREO or

STEREO ALC mode (S.R AIR mode can be also selected with

ADAPTER input).

MCACC SETUP MIC jack

Use to connect a microphone when performing Auto MCACC

setup (page 27).

Listening mode buttons

AUTO SURROUND/STREAM DIRECT

– Switches between

Auto surround mode (page 37) and Stream Direct

playback (page 38).

ALC/STANDARD SURR

– Press for standard decoding

and to switch between the modes of Pro Logic II,

Pro Logic IIx, Pro Logic IIz and NEO:6, and the Auto

level control stereo mode (page 37).

ADVANCED SURROUND

– Switches between the various

surround modes (page 38).

11 12 1514 17 1813

321 8 1049

19 20 21 23 24 21

27 28 29 30 30 3231

Controls and displays

ECO

Switches between ECO Mode 1/ECO Mode 2. When ECO

Mode is turned ON, the display will go dark (page 38).

iPod iPhone DIRECT CONTROL

Change the receiver’s input to the iPod and enable iPod

operations on the iPod (page 32).

iPod/iPhone terminals

Use to connect your Apple iPod/iPhone or USB mass storage

device as an audio source (page 24).

HDMI INPUT connector

Use for connection to a compatible HDMI device (Video

camera, etc.) (page 25).

Display

PHASE

Lights when the Phase Control is switched on.

AUTO

Lights when the Auto Surround feature is switched on

(page 37).

Tuner indicators

ST – Lights when a stereo FM broadcast is being received

in auto stereo mode (page 36).

TUNE – Lights when a normal broadcast channel.

PRESET – Shows when a preset radio station is registered

or called.

MEM – Blinks when a radio station is registered.

kHz/MHz – Lights when the character display is showing

the currently received AM/FM broadcast frequency.

ZONE

Lights when the MULTI-ZONE feature is active (page 58).

Speaker indicators

Shows if the speaker system is on or not (page 18).

Sleep timer indicator

Lights when the receiver is in sleep mode (page 11).

PRESET information or input signal indicator

Shows the preset number of the tuner or the input signal type,

etc.

Character display

Displays various system information.

DTS indicators

DTS – Lights when a source with DTS encoded audio

signals is detected.

HD – Lights when a source with DTS-EXPRESS or DTS-HD

encoded audio signals is detected.

ES – Lights to indicate DTS-ES decoding.

96/24 – Lights when a source with DTS 96/24 encoded

audio signals is detected.

NEO:6 – When one of the NEO:6 modes of the receiver is

on, this lights to indicate NEO:6 processing (page 37).

Dolby Digital indicators

D – Lights when a Dolby Digital encoded signal is

detected.

D+ – Lights when a source with Dolby Digital Plus

encoded audio signals is detected.

HD – Lights when a source with Dolby TrueHD

encoded audio signals is detected.

EX – Lights to indicate Dolby Digital EX decoding.

PLII(x) – Lights to indicate Pro Logic II decoding.

Light will go off during Pro Logic IIz decoding (see

Listening in surround sound on page 37 for more on this).

ADV.S.

Lights when one of the Advanced Surround modes has been

selected (see Using the Advanced surround on page 38 for

more on this).

SIGNAL SELECT indicators

DIGITAL – Lights when a digital audio signal is selected.

Blinks when a digital audio signal is selected and selected

audio input is not provided.

HDMI – Lights when an HDMI signal is selected. Blinks

when an HDMI signal is selected and selected HDMI input

is not provided.

Up Mix indicator

Lights when the Up Mix function is set to ON (page 39).

DIR.

Lights when the DIRECT or PURE DIRECT mode is switched

on (page 38).

Controls and displays

Remote control

•

The following buttons are not used with this receiver:

PTY

SLEEP

Press to change the amount of time before the receiver

switches into standby (30 min – 60 min – 90 min – Off). You

can check the remaining sleep time at any time by pressing

SLEEP

once.



STANDBY/ON

Switches the receiver between standby and on.

RECEIVER

CTRL

Switches the remote to control the receiver. Also use this

button to set up

HOME MENU

(page 53) or Audio parameters

(page 39).

SIGNAL SEL

S.SEL

Press to select the audio input signal of the component to play

back (page 29).

Input function buttons

Use to select the input source to this receiver (page 29). Also

switch the remote control mode when operating other device

and various inputs (

TUNER

, etc.).

Listening mode buttons

AUTO

– Switches between Auto surround mode (page 37)

and Stream Direct playback (page 38).

SURR

– Press for standard decoding and to switch

between the modes of Pro Logic II, Pro Logic IIx,

Pro Logic IIz and NEO:6, and the Auto level control

stereo mode (page 37).

ADV

– Switches between the various surround modes

(page 38).

Receiver and component control buttons

The following button controls can be accessed after you have

selected the corresponding input function button (

DVD

etc.).

Press

RECEIVER

first to access:

AUDIO P.

– Use to access the Audio options (page 39).

HOME MENU

– Press to access the Home Menu

(page 53).

RETURN

– Confirm and exit the current menu screen.

Press

and

DVD

first to access:

TOP MENU

– Displays the disc ‘top’ menu of a Blu-ray

Disc/DVD.

HOME MENU

– Displays the HOME MENU screen.

RETURN

– Confirm and exit the current menu screen.

– Displays the TOOLS menu of Blu-ray Disc player.

Press

TUNER

first to access:

TOOLS

– Memorizes stations for recall (page 36), also

used to change the name (page 36).

BAND

– Switches between AM, FM ST (stereo) and FM

MONO radio bands (page 36).

Press

iPod USB

first to access:

HOME MENU

– Switches between the iPod controls and

the receiver controls (page 31).

///-

ENTER

Use the arrow buttons when setting up your surround sound

system (page 53). Also used to control Blu-ray Disc/DVD

menus/options.

Component control buttons

The main buttons (





, etc.) are used to control a component

after you have selected it using the input function buttons.

The

DVD

, and

operation using the component control

buttons are limited only to Pioneer components.

The controls above these buttons can be accessed after you

have selected the corresponding input function button (

DVD

and

). These buttons also function as described

below.

Press

TUNER

first to access:

Use

TUNE +/–

can be used to find radio frequencies and

PRESET +/–

can be used to select preset radio stations

(page 36).

SUB TITLE

The subtitle will be switched for BD and DVD.

CD, NETWORK, iPod/USB, MHL, and BT

(ADPT) will be

random playback.

POP UP

Popup menu will be displayed for BD.

SLEEP

INPUT

MUTE

CTRL

AUTO SURR ADV

DVD

iPod

TUN

GAME

SAT

HDMI

MHL

NET

S.SEL ECO

STANDBY/ON

ENTER

CLR

SB CH

CH SEL

SP-A/B

Fav

RETURN

AUDIO P.

TOP

HOME

RECEIVER

RECEIVER SIGNAL SEL

SOURCE

TOOLS

SHIFT

BASS BASS

TRE TRE

SHIFT

Controls and displays

CD, NETWORK, iPod/USB, MHL, and BT

(ADPT) will be

repeat playback.

Other component controls

There are other buttons that can be accessed after

RECEIVER

is pressed.

SB CH

– Press to select ON, AUTO or OFF the surround

back channel (page 38).

CH SEL

– Press repeatedly to select a channel, then use

CH LEVEL +/–

to adjust the level (page 54).

CH LEVEL +/–

– Use to adjust the channel level.

BASS +/–

TRE +/–

– Use to adjust Bass or Treble.

• These controls are disabled when the listening mode is

set to DIRECT or PURE DIRECT.

• When the front speaker is set at SMALL in the Speaker

Setting (or automatically via the Auto MCACC setup)

and the X.Over is set above 150 Hz, the subwoofer

channel level will be adjusted by pressing

BASS +/–

(page 54).

DIMMER

– Dims or brightens the display. The

brightness can be controlled in four steps.

During ECO mode, the brightness switches between 2

levels. If the dimmest level is selected, DIMMER will be

shown on the display. (Mode other than ECO: 4 levels, ECO

mode: 2 levels)

SP-A/B

– See Switching the speaker terminal on page 18.

STATUS

– Switches the display of this unit. The

listening mode, input format, sound volume, Speaker

System setting or input name can be checked by selecting

an input source.

The Input format may or may not be displayed, depending

on the input source you have selected.

The Speaker System setting may or may not be displayed,

depending on the input source you have selected.



SOURCE

Press to turn on/off the power to the Pioneer device

connected to the receiver.

ECO

Switches between ECO Mode 1/ECO Mode 2. When ECO

Mode is turned ON, the display will go dark (page 38).

buttons

Operates a TV. When operating other manufacturer’s TV,

setup as follows.



– Use to turn on/off the power of the TV.

INPUT

– Use to select the TV input signal.

CH +/–

– Use to select channels.

VOL +/–

– Use to adjust the volume on your TV.

While holding down



button, press the input function

buttons (listed in the table below) for component you want to

control for about five seconds.

This may not operate depending on the TV.

Default setting: Pioneer

TV preset

MUTE

Mutes/unmutes the sound.

VOLUME +/–

Use to set the listening volume.

+Fav

Press while a song is being played back or stopped. The

selected song is then registered in the Favorites folder

(page 45).

DISP

Each entry source information will be displayed.

AUDIO

CLR

Songs and preset radio stations registered will be deleted

when NETWORK is selected.

Audio will be switched when set to other than NETWORK.

Loading the batteries

The batteries included with the unit are to check initial

operations; they may not last over a long period. We

recommend using alkaline batteries that have a longer life.

WARNING

•

Do not use or store batteries in direct sunlight or other

excessively hot place, such as inside a car or near a heater.

This can cause batteries to leak, overheat, explode or catch

fire. It can also reduce the life or performance of batteries.

CAUTION

•

Incorrect use of batteries may result in such hazards as

leakage and bursting. Observe the following precautions:

Never use new and old batteries together.

Insert the plus and minus sides of the batteries properly

according to the marks in the battery case.

Batteries with the same shape may have different

voltages. Do not use different batteries together.

When disposing of used batteries, please comply with

governmental regulations or environmental public

institution’s rules that apply in your country/area.

When inserting the batteries, make sure not to damage

the springs on the battery’s (–) terminals. This can cause

batteries to leak or overheat.

Input Function

button TV Brand

RECEIVER

CTRL

Pioneer

Panasonic

GAME

Sony

HDMI

Sharp

DVD

Toshiba

SAT

Mitsubishi

MHL

Philips/AOC/TPV

iPod

Vizio

Samsung

ADPT

LG Electric

TUNER

Skyworth

Hisense

NET

TCL

Controls and displays

Operating range of remote control

The remote control may not work properly if:

•

There are obstacles between the remote control and the

receiver’s remote sensor.

•

Direct sunlight or fluorescent light is shining onto the

remote sensor.

•

The receiver is located near a device that is emitting

infrared rays.

•

The receiver is operated simultaneously with another

infrared remote control unit.

30°

7 m (23 ft.)

30°

Chapter

Connecting your equipment

Determining the speakers’ application

The unit permits you to build various surround systems, in

accordance with the number of speakers you have.

If you have two subwoofers, the second subwoofer can be

connected to the SUBWOOFER 2 terminal. Connecting two

subwoofers increases the bass sound to achieve more

powerful sound reproduction.

In this case, the same sound is output from the two

subwoofers.

The 5.1 channel surround system is the most commonly-used

in home theaters. To achieve the best possible surround

sound, install your speakers as shown below.

Important

•

Both the surround back speakers and the front height

speakers can be connected at the same time. In this case,

sound will be output from either the front height speaker or

the surround back speaker depending on which one was

selected in the Speaker System setting (see The Speaker

System setting on page 57).

Speaker B connection

You can use the speakers connected to the B speaker

terminals to listen to stereo playback in another room. See

Switching the speaker terminal on page 18 for the listening

options with this setup.

•

You will not be able to connect the B speakers if you

connect the front height speakers in the main zone.

Further, if you use the B speakers, a 5.1 ch playback will be

the maximum in the main zone. (No sound is output from

the surround back speaker.)

Bi-amping connection

Bi-amping connection of the front speakers for high sound

quality with 5.1-channel surround sound.

•

When using the Front Bi-amping connection, sound will

only be output from the front speakers, the surround

speakers and the subwoofer.

ZONE 2 connection (Multi Zone)

With these connections you can simultaneously enjoy the

surround sound in the main zone with stereo playback on

another component in ZONE 2 (The selection of input devices

is limited). See MULTI-ZONE listening on page 58.

5.1 channel surround

system:

6.1 channel surround

(Surround back) system:

FHL

FHR

SBL

SBR

7.1 channel surround

(Surround back) system:

7.1 channel surround (Front

height) system:

Main zone

Speaker B

Front Bi-Amp

Main zone

Sub zone

Connecting your equipment

Some tips for improving sound quality

Where you put your speakers in the room has a big effect on

the quality of the sound. The following guidelines should help

you to get the best sound from your system.

•

It is best to angle the speakers towards the listening

position. The angle depends on the size of the room. Use

less of an angle for bigger rooms.

•

Refer to the chart below for placement of speakers you

intend to connect.

Place the surround speakers at 120º from the center. If

you, (1) use the surround back speaker, and, (2) don’t use

the front height speakers, we recommend placing the

surround speaker right beside you.

If you intend to connect only one surround back

speakers, place it directly behind you.

If the surround speakers cannot be set directly to the side

of the listening position with a 7.1-channel system, the

surround effect can be enhanced by turning off the Up

Mix function (see Setting the Up Mix function on page 39).

•

For the best stereo effect, place the front speakers 2 m to

3 m apart, at equal distance from the TV.

•

If you’re using a center speaker, place the front speakers at

a wider angle. If not, place them at a narrower angle.

•

Place the center speaker above or below the TV so that the

sound of the center channel is localized at the TV screen.

Also, make sure the center speaker does not cross the line

formed by the leading edge of the front left and right

speakers.

•

Surround and surround back speakers should be

positioned 60 cm to 90 cm higher than your ears and titled

slight downward. Make sure the speakers don’t face each

other. For DVD-Audio, the speakers should be more directly

behind the listener than for home theater playback.

•

Try not to place the surround speakers farther away from

the listening position than the front and center speakers.

Doing so can weaken the surround sound effect.

•

Place the left and right front height speakers at least one

meter directly above the left and right front speakers.

•

If you’re going to place speakers around your CRT TV, use

shielded speakers or place the speakers at a sufficient

distance from your CRT TV.

•

The subwoofer can be placed on the floor. Ideally, the other

speakers should be at about ear-level when you’re listening

to them. Putting the speakers on the floor (except the

subwoofer), or mounting them very high on a wall is not

recommended.

•

When not connecting a subwoofer, connect speakers with

low frequency reproduction capabilities to the front

channel. (The subwoofer’s low frequency component is

played from the front speakers, so the speakers could be

damaged.)

•

After connecting, be sure to conduct the Auto MCACC

(speaker environment setting) procedure.

See Automatically setting up for surround sound (MCACC)

on page 27.

CAUTION

•

Make sure that all speakers are securely installed. This not

only improves sound quality, but also reduces the risk of

damage or injury resulting from speakers being knocked

over or falling in the event of external shocks such as

earthquakes.

Connecting the speakers

The receiver will work with just two stereo speakers (the front

speakers in the diagram) but using at least three speakers is

recommended, and a complete setup is best for surround

sound.

Make sure you connect the speaker on the right to the right (R)

terminal and the speaker on the left to the left (L) terminal.

Also make sure the positive and negative (+/–) terminals on

the receiver match those on the speakers.

You can use speakers with a normal impedance between 6 

and 16 .

Be sure to complete all connections before connecting this unit

to the AC power source.

Bare wire connections

Twist exposed wire strands together.

Loosen terminal and insert exposed wire.

Tighten terminal.

Connect the wires to the B-Speakers terminals as shown below:

Twist exposed wire strands together.

Push open the tabs and insert exposed wire.

Release the tabs.

FHL

SBL SBR

FHR

30 30

120 120

12 3

10 mm

(3/8 in.)

12 3

10 mm

(3/8 in.)

Connecting your equipment

CAUTION

•

These speaker terminals carry HAZARDOUS LIVE voltage. To prevent the risk of electric

shock when connecting or disconnecting the speaker cables, disconnect the power cord

before touching any uninsulated parts.

•

Make sure that all the bare speaker wire is twisted together and inserted fully into the

speaker terminal. If any of the bare speaker wire touches the back panel it may cause the

power to cut off as a safety measure.

Connect the surround back or front height speakers

The Speaker System setting must be set if the above connections are performed. Select

Surr.Back if the surround back speaker is connected and Height if the front height speaker is

connected (If neither the surround back speaker nor the front height speaker is connected,

either setting will suffice) (see The Speaker System setting on page 57).

•

When using only one surround back speaker, connect it to the SURROUND BACK L (Single)

terminals.

Connection diagram

LINE LEVEL

INPUT LINE LEVEL

INPUT

FRONT

R L

SURROUND

R L

FRONT HEIGHT

R L

CENTER

PREOUT

SUBWOOFER

SURROUND BACK

R L

Front height setting

Speaker B setting

Front rightSubwoofer 1

Center

Front left

Surround

right

Surround

left

Surround back right Surround back left

Front height right

Speaker B – right

Front height left

Speaker B – left

The front height terminals can also be used for Speaker B.

The surround back terminals can also be used for ZONE 2.

5.1 ch surround setting

6.1 ch surround setting

7.1 ch surround setting

ZONE 2 setting

Not connected

Surround back

Not connected

ZONE 2 – Right ZONE 2 – Left

Subwoofer 2

Connecting your equipment

Front Bi-Amp connection

Hight

Low

Hight

Low

Center

Surround right

Front right Front left

Subwoofer 2

Surround left

Front height left

Front height

right

Subwoofer 1

Connecting your equipment

Switching the speaker terminal

When the The Speaker System setting on page 57 is set to

SPB, each press of the speaker button will switch the

speaker used for playback: SP, SPA, SPB, SPAB.

When the speaker system is set to SP-B: Each press of the

speaker button will switch the speaker used for playback: OFF,

A, B, AB.

When the speaker system is set to anything other than SP-B:

Each press of the speaker button will switch the speaker used

for playback: OFF, A. For more details on the speaker system

please refer to The Speaker System setting on page 57.

Press repeatedly to choose a speaker terminal option:

•

SPA – Sound is output from the speakers connected to

the A-speaker terminals (multichannel playback is

possible).

•

SPB – Sound is output from the two speakers connected

to the B-speaker terminals (only stereo playback is

possible).

•

SPAB – Sound is output from the A-speaker terminals,

the two speakers in the B-speaker terminals, and the

subwoofer. Multichannel sources are downmixed only

when the STEREO or STEREO ALC mode is selected for

stereo output from A- and B-speaker terminals.

•

SP – No sound is output from the speakers.

Note

•

The subwoofer output depends on the settings you made in

Speaker Setting on page 53. However, if SPB is selected

above, no sound is heard from the subwoofer (the LFE

channel is not downmixed).

•

All speaker terminals are switched off (SP) when

headphones are connected. SPB can be selected even

when headphones are connected.

Making cable connections

Make sure not to bend the cables over the top of this unit (as

shown in the illustration). If this happens, the magnetic field

produced by the transformers in this unit may cause a

humming noise from the speakers.

Important

•

Before making or changing connections, switch off the

power and disconnect the power cord from the AC outlet.

•

Before unplugging the power cord, switch the power into

standby.

HDMI cables

Both video and sound signals can be transmitted

simultaneously with one cable. If connecting the player and

the TV via this receiver, for both connections, use HDMI

cables.

Be careful to connect the terminal in the proper direction.

Note

•

Set the HDMI parameter in Setting the Audio options on

page 39 to THRU (THROUGH) and set the input signal in

Selecting the audio input signal on page 29 to HDMI, if you

want to hear HDMI audio output from your TV (no sound

will be heard from this receiver).

•

If the video signal does not appear on your TV, try adjusting

the resolution settings on your component or display. Note

that some components (such as video game units) have

resolutions that may not be displayed. In this case, use a

(analog) composite connection.

•

When the video signal from the HDMI is 480i, 480p, 576i or

576p, Multi Ch PCM sound and HD sound cannot be

received.

About HDMI

The HDMI connection transfers uncompressed digital video,

as well as almost every kind of digital audio that the

connected component is compatible with, including DVD-

Video, DVD-Audio, SACD, Dolby Digital Plus, Dolby TrueHD,

DTS-HD Master Audio (see below for limitations), Video CD/

Super VCD and CD.

This receiver incorporates High-Definition Multimedia

Interface (HDMI®) technology.

This receiver supports the functions described below through

HDMI connections.

•

Digital transfer of uncompressed video (contents protected

by HDCP (1080p/24, 1080p/60, etc.))

•

3D signal transfer

•

Deep Color signal transfer

•

x.v.Color signal transfer

•

Audio Return Channel

•

Input of multi-channel linear PCM digital audio signals

(192 kHz or less) for up to 8 channels

•

Input of the following digital audio formats:

– Dolby Digital, Dolby Digital Plus, DTS, High bitrate audio

(Dolby TrueHD, DTS-HD Master Audio), DVD-Audio, CD,

SACD (DSD 2 ch only), Video CD, Super VCD

•

Synchronized operation with components using the

Control with HDMI function (see Control with HDMI

function on page 59)

•

4K signal transfer

– This may not operate properly, depending on the

connected equipment.

– 4K 24p, 4K 25p, 4K 30p, 4K 50p and 4K 60p signals are

supported

Note

•

Use a High Speed HDMI®/™ Cable. If HDMI cable other

than a High Speed HDMI®/™ Cable is used, it may not work

properly.

•

When an HDMI cable with a built-in equalizer is connected,

it may not operate properly.

•

3D, Deep Color, x.v.Color, 4K signal transfer and Audio

Return Channel are only possible when connected to a

compatible component.

•

HDMI format digital audio transmissions require a longer

time to be recognized. Due to this, interruption in the audio

may occur when switching between audio formats or

beginning playback.

HDMI

Connecting your equipment

•

Turning on/off the device connected to this unit’s HDMI

OUT terminal during playback, or disconnecting/

connecting the HDMI cable during playback, may cause

noise or interrupted audio.

The terms HDMI and HDMI High-Definition Multimedia

Interface, and the HDMI Logo are trademarks or registered

trademarks of HDMI Licensing, LLC in the United States and

other countries.

“x.v.Color” and are trademarks of Sony

Corporation.

Analog audio cables

Use stereo RCA phono cables to connect analog audio

components. These cables are typically red and white, and

you should connect the red plugs to R (right) terminals and

white plugs to L (left) terminals.

Digital audio cables

Commercially available coaxial digital audio cables or optical

cables should be used to connect digital components to this

receiver.

Note

•

When connecting optical cables, be careful when inserting

the plug not to damage the shutter protecting the optical

socket.

•

When storing optical cable, coil loosely. The cable may be

damaged if bent around sharp corners.

•

You can also use a standard RCA video cable for coaxial

digital connections.

Video cables

Standard RCA video cables

These cables are the most common type of video connection

and are used to connect to the composite video terminals. The

yellow plugs distinguish them from cables for audio.

Component video cables

Use component video cables to get the best possible color

reproduction of your video source. The color signal of the TV is

divided into the luminance (Y) signal and the color (PB and PR)

signals and then output. In this way, interference between the

signals is avoided.

About video outputs connection

This receiver is not loaded with a video converter. When you

use HDMI cables for connecting to the input device, the same

cables should be used for connecting to the TV.

The signals input from the analog (composite) video inputs of

this unit will not be output from the HDMI OUT terminal.

AUDIO

Red (Right)

White (Left)

COAXIAL

OPTICAL

Coaxial digital

audio cable

Optical cable

VIDEO

Yellow

COMPONENT VIDEO

Green (Y)

Red (PR)

Blue (PB)

VIDEO

IN IN

HDMI

MONITOR

OUT

HDMI

OUT

Terminal for connection with

source device

Terminal for connection

with TV monitor

Playback component

The OSD will

not appear.

Video signals can be output.

Connecting your equipment

Connecting a TV and playback components

Connecting using HDMI

If you have an HDMI or DVI (with HDCP) equipped component

(Blu-ray Disc player, etc.), you can connect it to this receiver

using a commercially available HDMI cable.

If the TV and playback components support the Control with

HDMI feature, the convenient Control with HDMI functions

can be used (see Control with HDMI function on page 59).

•

The following connection/setting is required to listen to the

sound of the TV over this receiver.

If the TV does not support the HDMI Audio Return

Channel function, connect the receiver and TV with audio

cables (as shown).

If the TV supports the HDMI Audio Return Channel

function, the sound of the TV can be input to the receiver

via the HDMI terminal, so there is no need to connect an

audio cable. In this case, set ARC at HDMI Setup to ON

(see HDMI Setup on page 59).

Please refer to the TV’s operation manual for directions

on connections and setup for the TV.

Note

•

In order to listen to the audio from the TV that is connected

to this receiver using an analog audio cables, set-up for

analog audio input is required (see The Input Assign menu

on page 55).

On 4K support for HDMI input terminal

Supports the following HDMI input terminals:

•

(BD, GAME, SAT/CBL)- 4K/60p, 4K/50p, 4K/30p, 4K/25p,

4K/24p.

•

(DVD, MHL)- 4K/30p, 4K/25p, 4K/24p.

HDMI

OUT

ANALOG

IN1 (CD)

HDMI OUT

HDMI IN

DIGITAL AUDIO OUT

OPTICAL

HDMI OUT

HDMI IN

ANALOG AUDIO OUT

OPTICAL

IN1 (TV)

Select one

HDMI/DVI-compatible TV

Game console

DVD player Blu-ray Disc player

Set-top box

HDMI/DVI-compatible components

If the TV does not support

the HDMI Audio Return

Channel function, this

connection is required to

listen to the TV sound over

the receiver.

DVD recorder,

Blu-ray Disc recorder

MHL-compatible device

Connecting your equipment

Connecting your TV with no HDMI input

This diagram shows connections of a TV (with no HDMI input)

and DVD player (or other playback component) to the receiver.

•

With these connections, the picture is not output to the TV

even if the DVD player is connected with an HDMI cable.

Connect the DVD player’s video signals using a composite

cable.

•

In order to listening to HD audio with this receiver, connect

an HDMI cable, and use analog video cable for video signal

input.

Depending on the player, it may not be possible to output

video signals to both HDMI and other video output

(composite, etc.) simultaneously, and it may be necessary

to make video output settings. Please refer to the

operating instructions supplied with your player for more

information.

Important

•

When the receiver and TV are connected by composite

cable, the OSD function allowing display of the receiver’s

settings, operations, etc., on the TV’s screen cannot be

used. In this case, watch the receiver’s front panel display

while performing the various operations and making

settings.

Note

•

In order to listen to the audio from the TV that is connected

to this receiver using a analog audio cables, set-up for

analog audio input is required (see The Input Assign menu

on page 55).

•

Only one component can be connected to both the optical

input terminal and coaxial input terminal. If connecting

other devices, please use a different method to connect the

audio.

In order to listen to the audio from the source component

that is connected to this receiver using an optical cable or

a coaxial cable, first, switch to the DVD (DVD player) or

SAT/CBL (set-top box), then use

S. SEL

to choose the

audio signal O1 (OPTICAL1) or C1 (COAXIAL1) (see

Selecting the audio input signal on page 29).

ANALOG

IN1 (CD)

VIDEO IN

DIGITAL AUDIO OUT

OPTICAL

ANALOG AUDIO OUT

OPTICAL

IN1 (TV)

DVD IN

SAT/CBL IN

VIDEO OUT

DIGITAL AUDIO OUT

OPTICALCOAXIAL

ANALOG AUDIO OUT

VIDEO OUT

COAXIAL

IN1 (CD)

MONITOR

OUT

DIGITAL AUDIO OUT

OPTICALCOAXIAL

HDMI OUT

HDMI

DVD IN

Select one Select one

Select one

DVD player Set-top box

This connection is

required in order to

listen to the sound

of the TV over the

receiver.

Connecting your equipment

Connecting optional

Bluetooth

ADAPTER

When the Bluetooth ADAPTER (Pioneer Model No. AS-BT100

or AS-BT200) is connected to this unit, a product equipped

with Bluetooth wireless technology (portable cell phone,

digital music player, etc.) can be used to listen to music

wirelessly.



Connect a

Bluetooth

ADAPTER to the ADAPTER PORT

terminal on the rear panel.

•

For instructions on playing the Bluetooth wireless

technology device, see Pairing the Bluetooth ADAPTER and

Bluetooth wireless technology device on page 34.

Important

•

Do not move the receiver with the Bluetooth ADAPTER

connected. Doing so could cause damage or faulty contact.

Connecting to the network through LAN

interface

By connecting this receiver to the network via the LAN

terminal, you can listen to Internet radio stations. To listen to

Internet radio stations, you must sign a contract with an ISP

(Internet Service Provider) beforehand.

When connected in this way, you can play audio files stored

on the components on the local network, including your

computer.

Connect the LAN terminal on this receiver to the LAN terminal

on your router (with or without the built-in DHCP server

function) with a straight LAN cable (CAT 5 or higher).

Turn on the DHCP server function of your router. In case your

router does not have the built-in DHCP server function, it is

necessary to set up the network manually. For details, see The

Network Setup menu on page 46.

Note

•

Refer to the operation manual of the equipment you have as

the connected equipment and connection method may

differ depending on your Internet environment.

•

When using a broadband Internet connection, a contract

with an Internet service provider is required. For more

details, contact your nearest Internet service provider.

Connecting to a wireless LAN

Wireless connection to the network is possible through a

wireless LAN connection. Use the separately sold AS-WL300

for connection.

For details, refer to the operating instructions of the wireless

LAN converter.

Bluetooth® ADAPTER

WAN

LAN

to LAN port

LAN cable (sold

separately)

Router

Modem

Internet

DC 5V WPS

Ethernet

WAN

Internet

Modem

Router

Wireless LAN converter (AS-WL300)

Connecting your equipment

Connecting antennas

Connect the AM loop antenna and the FM wire antenna as

shown below. To improve reception and sound quality,

connect external antennas (see Using external antennas

below).

Push open the tabs, then insert one wire fully into each

terminal, then release the tabs to secure the AM

antenna wires.

Fix the AM loop antenna to the attached stand.

To fix the stand to the antenna, bend in the direction

indicated by the arrow (fig. a) then clip the loop onto the

stand (fig. b).

Place the AM antenna on a flat surface and in a

direction giving the best reception.

Connect the FM wire antenna into the FM antenna

socket.

For best results, extend the FM antenna fully and fix to a

wall or door frame. Don’t drape loosely or leave coiled up.

Using external antennas

To improve FM reception

Use an F connector (not supplied) to connect an external FM

antenna.

To improve AM reception

Connect a 5 m to 6 m (16 ft. to 20 ft.) length of vinyl-coated

wire to the AM antenna terminal without disconnecting the

supplied AM loop antenna.

For the best possible reception, suspend horizontally

outdoors.

fig. a fig. b

FM UNBAL

F connector

Outdoor

antenna

5 m to 6 m

(16 ft. to 20 ft.)

Indoor antenna

(vinyl-coated

wire)

Connecting your equipment

Connecting an IR receiver

If you keep your stereo components in a closed cabinet or

shelving unit, or you wish to use the sub zone remote control

in another zone, you can use an optional IR receiver (such as

a Niles or Xantech unit) to control your system instead of the

remote sensor on the front panel of this receiver.

Note

•

Remote operation may not be possible if direct light from a

strong fluorescent lamp is shining on the IR receiver

remote sensor window.

•

Note that other manufacturers may not use the IR terminology.

Refer to the manual that came with your component to check for

IR compatibility.



Connect the IR receiver sensor to the IR IN jack on the

rear of this receiver.

For more information on connecting the IR receiver, see the

Installation Instructions for the IR Receiver.

Switching components on and off using the 12

volt trigger

You can connect components in your system (such as a

screen or projector) to this receiver so that they switch on or

off using 12 volt triggers when you select an input function.

However, you must specify which input functions switch on

the trigger using the The 12 V Trigger Setting on page 57. Note

that this will only work with components that have a standby

mode.



Connect the 12 V TRIGGER jack of this receiver to the 12

V trigger of another component.

Use a cable with a mono mini-plug on each end for the

connection.

After you’ve specified the input functions that will switch on

the trigger, you’ll be able to switch the component on or off

just by pressing the input function(s) you’ve set on page 57.

Connecting an iPod

This receiver has a dedicated iPod/iPhone terminals that will

allow you to control playback of audio content from your iPod

using the controls of this receiver.

Note

•

An iPod/iPhone can be connected to the receiver. For

details on supported models and versions of the respective

products, see Playing an iPod on page 31.



Switch the receiver into standby, and then use the iPod

cable to connect your iPod to the iPod/iPhone terminals

on the front panel of this receiver.

•

For the cable connection, also refer to the operating

instructions for your iPod.

•

When connecting an iPhone to this unit, keep the iPhone

at least 20 cm away from this unit. If the iPhone is kept

closer to this unit and a telephone call is received by the

iPhone, noise may be output from this device.

Other component

Closet or shelving unit

IR receiver

12 V TRIGGER

INPUT

iPod/iPhone

USB cable that

comes with the iPod

Connecting your equipment

•

iPod recharging occurs whenever an iPod is connected to

this unit. (Recharging is enabled only when the unit’s

power is turned on.)

•

For instructions on playing the iPod, see Playing an iPod on

page 31.

Connecting a USB device

It is possible to play audio and photo files by connecting USB

devices to this receiver.



Switch the receiver into standby then connect your USB

device to the iPod/iPhone terminals on the front panel of

this receiver.

•

This receiver does not support a USB hub.

•

For instructions on playing the USB device, see Playing a

USB device on page 31.

Connecting a MHL-compatible device

An MHL-compatible mobile device can be connected to enjoy

full-HD videos, high quality multi-channel audio, and photos

etc., with charge the battery on the receiver. Use the MHL

cable (sold separately) to connect the device.



Switch the receiver into standby then use the MHL cable

(sold separately) to connect your MHL enabled device to

the MHL terminal on the front panel of this receiver.

•

The MHL-compatible device is recharged whenever it is

connected to this unit. (Recharging is enabled only when

the unit’s power is turned on.)

•

For instructions on playing the MHL-compatible device, see

Playing a MHL-compatible device on page 33.

Note

•

Do not place the MHL device on this unit which has the

power turned ON.

Enjoy Roku video streaming service

Connect the Roku Streaming Stick (sold separately) to the

MHL

terminal on the receiver to enjoy video streaming, see

Enjoy Roku video streaming service on page 33.

•

When the Roku Streaming Stick (sold separately) is

connected to the receiver via the MHL terminal, and the

power switched on for the first time, a setup screen will be

displayed. Setup can be changed later on as well, see Setup

ROKU standby mode on page 56.

•

When the Roku Streaming Stick (sold separately) is

inserted, the unit will switch to MHL input.

Connecting an HDMI-equipped component to

the front panel input

USB mass

storage device

MHL-compatible

device

MHL cable (sold

separately)

Video camera (etc.)

Connecting your equipment

Plugging in the receiver

Only plug in after you have connected all your components to

this receiver, including the speakers.



Plug the AC power cord into a convenient AC power

outlet.

CAUTION

•

Handle the power cord by the plug. Do not pull out the plug

by tugging the cord and never touch the power cord when

your hands are wet as this could cause a short circuit or

electric shock. Do not place the unit, a piece of furniture,

etc., on the power cord, or pinch the cord. Never make a

knot in the cord or tie it with other cords. The power cords

should be routed such that they are not likely to be stepped

on. A damaged power cord can cause a fire or give you an

electrical shock. Check the power cord once in a while.

When you find it damaged, ask your nearest PIONEER

authorized service center or your dealer for a replacement.

•

The receiver should be disconnected by removing the

mains plug from the wall socket when not in regular use,

e.g., when on vacation.

Note

•

After this receiver is connected to an AC outlet, a 2 second

to 10 second HDMI initialization process begins. You

cannot carry out any operations during this process. The

HDMI indicator in the front panel display blinks during this

process, and you can turn on this receiver once it has

stopped blinking. When you set the Control with HDMI to

OFF, you can skip this process. For details about the

Control with HDMI feature, see HDMI Setup on page 59.

Chapter

Basic Setup

Automatically setting up for surround sound

(MCACC)

The Auto Multi-Channel ACoustic Calibration (MCACC) setup

measures the acoustic characteristics of your listening area,

taking into account ambient noise, speaker size and distance,

and tests for both channel delay and channel level. After you

have set up the microphone provided with your system, the

receiver uses the information from a series of test tones to

optimize the speaker settings and equalization for your

particular room.

CAUTION

•

The test tones used in the Auto MCACC setup are output at

high volume.

Important

•

The OSD will not appear if you have connected using the

composite output to your TV. Use HDMI connection for

Auto MCACC setup.

•

The Auto MCACC setup will overwrite any existing speaker

settings you’ve made.

•

Before using the Auto MCACC setup, the NETRADIO,

PANDORA, M.SERVER, FAVORITE, iPod/USB or

ADAPTER input should not be selected as an input source.

•

When both the surround back speaker and the front height

speaker are connected, conduct Auto MCACC setup twice:

once with the Speaker System setting is in Surr.Back and

once with the Speaker System setting is in Height. (There

is no need to conduct Auto MCACC setup every time the

Speaker System setting is changed.)

Switch on the receiver and your TV.

Switch the TV input to the input that connects this

receiver to the TV through the corresponding HDMI

cable.

Connect the microphone to the MCACC SETUP MIC jack

on the front panel.

Make sure there are no obstacles between the speakers

and the microphone.

If you have a tripod, use it to place the microphone so that

it’s about ear level at your normal listening position.

Otherwise, place the microphone at ear level using a

table or a chair.

Press BD button on the remote control to switch to BD

entry.

Press

RECEIVER

on the remote control, then press the

HOME MENU

button.

The Home Menu appears on your TV. Use

///-

and

ENTER

on the remote control to navigate through the

screens and select menu items. Press

RETURN

to exit

the current menu.

•

Press

HOME MENU

at any time to exit the Home

Menu. If you cancel the Auto MCACC setup at any

time, the receiver automatically exits and no settings

will be made.

•

The screensaver automatically starts after three

minutes of inactivity.

Select ‘Auto MCACC’ from the Home Menu, then press

ENTER

•

Mic In! blinks when the microphone is not connected

to MCACC SETUP MIC jack.

Try to be as quiet as possible after pressing

ENTER

. The

system outputs a series of test tones to establish the

ambient noise level.

Follow the instructions on-screen.

•

Make sure the microphone is connected.

•

Make sure the subwoofer is on and the volume is

turned up.

•

When using surround back or front height speakers,

turn on the power to the amplifier to which the

surround back or front height speakers are connected,

and adjust the sound level to the desired level.

•

See below for notes regarding background noise and

other possible interference.

SLEEP

INPUTCTRL

BD GAME HDMI

S.SEL ECO

STANDBY/ON

RECEIVER SIGNAL SEL

SOURCE

STANDBY/ON

RECEIVER

CTRL

ENTER

RETURN

AUDIO

TOP

HOME

TOOLS

BAND PTY

ENTER

RETURNHOME

Tripod

Microphone

Home Menu

. Auto MCACC

. Manual SP Setup

. Input Assign

4. Auto Power Down

5. HDMI Setup

6. Network Standby

7. MHL Setup

8. Speaker System

9. 12V Trigger

10. OSD Setup

Basic Setup

Wait for the test tones to finish.

A progress report is displayed on-screen while the

receiver outputs test tones to determine the speakers

present in your setup. Try to be as quiet as possible while

it’s doing this.

•

For correct speaker settings, do not adjust the volume

during the test tones.

Confirm the speaker configuration.

The configuration shown on-screen should reflect the

actual speakers you have.

•

With error messages (such as Too much ambient

noise) select RETRY after checking for ambient noise

(see Other problems when using the Auto MCACC

setup below).

If the speaker configuration displayed isn’t correct, use

/

to select the speaker and

/-

to change the

setting. When you’re finished, go to the next step.

If you see an error message (ERR) in the right side

column, there may be a problem with the speaker

connection. If selecting RETRY doesn’t fix the problem,

turn off the power and check the speaker connections.

Make sure ‘OK’ is selected, then press

ENTER

If the screen in step 9 is left untouched for 10 seconds

and

ENTER

is not pressed in step 10, the Auto MCACC

setup will start automatically as shown.

A progress report is displayed on-screen while the

receiver outputs more test tones to determine the

optimum receiver settings for channel level, speaker

distance, X.Over, and Acoustic Calibration EQ.

Again, try to be as quiet as possible while this is

happening. It may take 1 to 3 minutes.

The Auto MCACC setup has finished! You return to the

Home Menu.

The settings made in the Auto MCACC setup should give

you excellent surround sound from your system, but it is

also possible to adjust these settings manually using the

Home Menu (starting on page 53).

Note

•

Depending on the characteristics of your room, sometimes

identical speakers with cone sizes of around 12 cm

(5 inches) will end up with different size settings. You can

correct the setting manually using the Speaker Setting on

page 53.

•

The subwoofer distance setting may be farther than the

actual distance from the listening position. This setting

should be accurate (taking delay and room characteristics

into account) and generally does not need to be changed.

Other problems when using the Auto MCACC

setup

If the room environment is not optimal for the Auto MCACC

setup (too much background noise, echo off the walls,

obstacles blocking the speakers from the microphone) the

final settings may be incorrect. Check for household

appliances (air conditioner, fridge, fan, etc.), that may be

affecting the environment and switch them off if necessary. If

there are any instructions showing in the front panel display,

please follow them.

•

Some older TVs may interfere with the operation of the

microphone. If this seems to be happening, switch off the

TV when doing the Auto MCACC setup.

. Auto MCACC

Now Analyzing

Environment Check

Ambient Noise

Speaker YES/NO

Return

. Auto MCACC

Check

Return

10:Next

Front

Center

Surr

Surr. Back

Subwoofer

[ YES ]

[YESx2]

[ YES ]

. Auto MCACC

Now Analyzing

Surround Analyzing

Speaker System

X.Over

Speaker Distance

Channel Level

Acoustic Cal EQ

Return

Chapter

Basic playback

Playing a source

Here are the basic instructions for playing a source (such as

a DVD disc) with your home theater system.

Switch on your system components and receiver.

Start by switching on the playback component (for

example a DVD player), your TV and subwoofer (if you

have one), then the receiver (press



STANDBY/ON

•

Make sure the setup microphone is disconnected.

Switch the TV input to the input that connects this

receiver.

For example, if you connected this receiver to the VIDEO

jacks on your TV, make sure that the VIDEO input is now

selected.

Press input function buttons to select the input function

you want to play.

•

The input of the receiver will switch over, and you will

be able to operate other components using the remote

control. To operate the receiver, first press

RECEIVER

on the remote control, then press the appropriate

button to operate.

•

The input source can also be selected by using the

front panel

INPUT SELECTOR

dial. In this case, the

remote control won’t switch operational modes.

If you selected the proper input source and there is still

no sound, select the audio input signal for playback (see

Selecting the audio input signal below).

Press

AUTO

to select ‘AUTO SURROUND’ and start

playback of the source.

If you’re playing a Dolby Digital or DTS surround sound

DVD disc, with a digital audio connection, you should

hear surround sound. If you’re playing a stereo source or

if the connection is an analog audio connection, you will

only hear sound from the front left/right speakers in the

default listening mode.

It is possible to check on the front panel display whether

or not surround sound playback is being performed

properly.

When using a surround back speaker, D+PLIIx and

D+PLII are displayed when playing Dolby Digital 5.1-

channel signals, and DTS+NEO:6 is displayed when

playing DTS 5.1-channel signals.

When not using a surround back speaker, D is

displayed when playing Dolby Digital signals.

If the display does not correspond to the input signal and

listening mode, check the connections and settings.

Note

•

You may need to check the digital audio output settings on

your DVD player or digital satellite receiver. It should be set

to output Dolby Digital, DTS and 88.2 kHz/96 kHz PCM (2

channel) audio, and if there is an MPEG audio option, set

this to convert the MPEG audio to PCM.

•

Depending on your DVD player or source discs, you may

only get digital 2 channel stereo and analog sound. In this

case, the receiver must be set to a multichannel listening

mode if you want multichannel surround sound.

Use

VOLUME +/–

to adjust the volume level.

Turn down the volume of your TV so that all sound is

coming from the speakers connected to this receiver.

Selecting the audio input signal

The audio input signal can be selected for each input source.

Once it is set, the audio input that was selected will be applied

whenever you select the input source using the input function

buttons.



Press

SIGNAL SEL

to select the audio input signal

corresponding to the source component.

Each press cycles through the following:

•

H – Selects an HDMI signal. H can be selected for BD,

DVD, SAT/CBL, MHL or GAME input. For other inputs,

H cannot be selected.

When the HDMI option in Setting the Audio options

on page 39 is set to THRU, the sound will be heard

through your TV, not from this receiver.

•

A – Selects the analog inputs.

•

C1/O1 – Selects the digital input. The coaxial 1 input is

selected for C1, and the optical 1 audio input is

selected for O1.

When H (HDMI) or C1/O1 (digital) is selected and the

selected audio input is not provided, A (analog) is

automatically selected.

Note

•

BD, MHL and GAME inputs are fixed to H (HDMI). It cannot

be changed.

•

For the TV input, only A (analog) or C1/O1 (digital) can be

selected. However, if the ARC at HDMI Setup is set to ON,

the input is fixed to H (HDMI) and cannot be changed.

•

When set to H (HDMI) or C1/O1 (digital), lights when

a Dolby Digital signal is input, and DTS lights when a DTS

signal is input.

•

When the H (HDMI) is selected, the A and DIGITAL

indicators are off (see page 10).

SLEEP

INPUTCTRL

DVD

iPod

TUN

GAME

SAT

HDMI

MHL

NET

S.SEL ECO

STANDBY/ON

RECEIVER SIGNAL SEL

SOURCE

DVD

iPod

TUN

GAME

SAT

HDMI

MHL

NET

STANDBY/ON

MUTE

AUTO SURR ADV

ENTER

Fav

RETURN

AUDIO P.

TOP

HOME

TOOLS

BAND PTY

AUTO SURR ADV

SLEEP

INPUTCTRL S.SEL ECO

STANDBY/ON

RECEIVER SIGNAL SEL

SOURCE

S.SEL

SIGNAL SEL

Basic playback

•

When digital input (optical or coaxial) is selected, this

receiver can only play back Dolby Digital, PCM (32 kHz to

96 kHz) and DTS (including DTS 96 kHz/24 bit) digital signal

formats. The compatible signals via the HDMI terminals

are: Dolby Digital, DTS, SACD (DSD 2 ch only), PCM

(32 kHz to 192 kHz sampling frequencies), Dolby TrueHD,

Dolby Digital Plus, DTS-EXPRESS, DTS-HD Master Audio

and DVD Audio (including 192 kHz). With other digital

signal formats, set to A (analog).

•

You may get digital noise when a LD or CD player

compatible with DTS is playing an analog signal. To prevent

noise, make the proper digital connections (page 19) and

set the signal input to C1/O1 (digital).

•

Some DVD players don’t output DTS signals. For more

details, refer to the instruction manual supplied with your

DVD player.

Tip

•

In order to enjoy the picture and/or sound from devices connected to each terminal, select the input by doing the following.

DVD BD

TUNER

ADAPTER

SAT/CBL

DVD

SAT/CBL

DVD

SAT/CBL

GAME MHL NETWORK

DVD

MHL

CD TV

RECEIVER SIGNAL SEL

S.SELCTRL

RECEIVER SIGNAL SEL

S.SELCTRL

S.SEL

CTRL

S.SELCTRL

Audio

Video/Audio (HDMI)

Video

Other than TV input

(TV input)

Video

Reassignable

(page 55)

ANALOG IN1 audio input terminal is

assigned to CD under factory settings. If

you want to change this to TV input,

please change the settings in the Input

Assign menu (page 55).

Basic playback

Playing an iPod

This receiver has the iPod iPhone USB terminal that will allow

you to control playback of audio content from your iPod using

the controls of this receiver.

Important

•

Pioneer cannot under any circumstances accept

responsibility for any direct or indirect loss arising from any

inconvenience or loss of recorded material resulting from

the iPod failure.

•

About one minute is required between turning the power

on and completion of startup.

•

USB works with iPhone 5s, iPhone 5c, iPhone 5, iPhone 4s,

iPhone 4, iPhone 3GS, iPhone 3G, iPhone, iPod touch (1st

through 5th generation) and iPod nano (3rd through 7th

generation). Howerver, some of the functions may be

restricted for some models.

•

This receiver has been developed and tested for the

software version of iPod/iPhone indicated on the website of

Pioneer (http://pioneer.jp/homeav/support/ios/na/).

•

Installing software versions other than indicated on the

website of Pioneer to your iPod/iPhone may result in

incompatibility with this receiver.

•

iPod and iPhone are licensed for reproduction of non-

copyrighted materials or materials the user is legally

permitted to reproduce.

•

Features such as the equalizer cannot be controlled using

this receiver, and we recommend switching the equalizer

off before connecting.

•

Make sure the receiver is in standby when disconnecting

the iPod/iPhone.

Switch on the receiver and your TV.

See Connecting an iPod on page 24.

Switch the TV input so that it connects to the receiver.

•

Switch the TV input to the input that connects this

receiver to the TV through the corresponding HDMI

cable.

Press

iPod USB

to switch the receiver to the iPod/USB

input.

When the display shows the names of folders and files,

you’re ready to play music from the iPod.

•

If after pressing

iPod USB

the display shows NO

DEVICE, try switching off the receiver and

reconnecting the iPod to the receiver.

•

The controls of your iPod will be inoperable when

connected to this receiver.

Playing back files stored on an iPod

To navigate songs on your iPod, you can take advantage of the

OSD of your TV connected to this receiver.

•

Note that non-roman characters in the title are displayed as

‘#’.

•

This feature is not available for photos or video clips on your

iPod.

Finding what you want to play

When your iPod is connected to this receiver, you can browse

songs stored on your iPod by playlist, artist, album name,

song name, genre or composer, similar to using your iPod

directly.

Use

/

to select a category, then press

ENTER

browse that category.

•

When  or  is pressed at the list screen, the

page switches.

•

To return to the previous level any time, press

RETURN

Use

/

to browse the selected category (e.g.,

albums).

•

Use

/-

to move to previous/next levels.

Continue browsing until you arrive at what you want to

play, then press



to start playback.

Tip

•

If you’re in the song category, you can also press

ENTER

start playback.

•

You can play all of the songs in a particular category by

selecting the All item at the top of each category list. For

example, you can play all the songs by a particular artist.

Basic playback controls

This receiver’s remote control buttons can be used for basic

playback of files stored on an iPod.

•

Press

iPod USB

to switch the remote control to the iPod/

USB operation mode.

Switches between the iPod controls and the

receiver controls

This allows you to switch between performing iPod operations

via the receiver remote control or on the iPod itself.



Press

HOME MENU

to switch to the iPod controls.

•

Press

HOME MENU

again to switch back to the receiver

controls when you’re done.

Tip

•

Change the receiver’s input to the iPod in one action by

pressing

iPod iPhone DIRECT CONTROL

on the front

panel to enable iPod operations on the iPod.

Playing a USB device

It is possible to play files using the USB interface on the front

of this receiver.

Important

•

Pioneer cannot guarantee compatibility (operation and/or

bus power) with all USB mass storage devices and

assumes no responsibility for any loss of data that may

occur when connected to this receiver.

•

About one minute is required between turning the power

on and completion of startup.

MUTE

AUTO SURR ADV

ENTER

RETURN

AUDIO P.

TOP

HOME

TOOLS

BAND PTY

ENTER

RETURN

AUDIO P.

TOP

CLR

SB CH

CH SEL

Fav

RETURNHOME

SHIFT

BASS BASS

TRE TRE

BAND PTY

Basic playback

Note

•

Compatible USB devices include external magnetic hard

drives, portable flash memory (particularly keydrives) and

digital audio players (MP3 players) of format FAT16/32.

•

Copyrighted audio files cannot be played back on this

receiver.

•

With large amounts of data, it may take longer for the

receiver to read the contents of a USB device.

•

If the file selected cannot be played back, this receiver

automatically skips to the next file playable.

•

When the file currently being played back has no title

assigned to it, the file name is displayed in the OSD instead;

when neither the album name nor the artist name is

present, the row is displayed as a blank space.

•

Note that non-roman characters in the playlist are

displayed as ‘#’.

•

Make sure the receiver is in standby when disconnecting

the USB device.

Switch on the receiver and your TV.

See Connecting a USB device on page 25.

Switch the TV input so that it connects to the receiver.

•

Switch the TV input to the input that connects this

receiver to the TV through the corresponding HDMI

cable.

Press

iPod USB

on the remote control to switch the

receiver to the iPod/USB input.

When the display shows the names of folders and files,

you’re ready to play from the USB device.

If a USB Error message lights in the display, try following

the points below:

•

Switch the receiver off, then on again.

•

Reconnect the USB device with the receiver switched

off.

•

Select another input source (like BD), then switch back

to iPod/USB.

•

Use a dedicated AC adapter (supplied with the device)

for USB power.

If this doesn’t remedy the problem, it is likely your USB

device is incompatible.

Playing back audio files stored on a USB memory

device

The maximum number of levels that you can select in Step 1

(below) is 9.

•

Note that non-Roman characters in the playlist are

displayed as ‘#’.

Use

/

to select a folder, then press

ENTER

to browse

that folder.

•

To return to the previous level any time, press

RETURN

Continue browsing until you arrive at what you want to

play, then press



to start playback.

Basic playback controls

This receiver’s remote control buttons can be used for basic

playback of files stored on USB devices.

•

Press

iPod USB

to switch the remote control to the iPod/

USB operation mode.

Playing back photo files stored on a USB memory

device

Use

/

to select a folder, then press

ENTER

to browse

that folder.

•

For high resolution files, some time may be required

for the photo to appear.

•

To return to the previous level any time, press

RETURN

Continue browsing until you arrive at what you want to

play, then press



to start playback.

The selected content is displayed in full screen and a

slideshow starts.

Basic playback controls

ENTER



– Starts displaying a photo and playing a slideshow.



– Stops the player and returns to the previous menu.

Tip

•

Slideshows of photo files can be played while listening to

music files by returning to the folder/file list display while

playing a music file on a USB device then playing the photo

files.

About playable file formats

The USB function of this receiver supports the following file

formats. Note that some file formats are not available for

playback although they are listed as playable file formats.

With MP3, WAV, AAC, FLAC, AIFF and Apple Lossless files,

when music files with the same format, sampling frequency,

quantization bit number and number of channels are played

successively, they are played with no gap.

Make sure the gap is at the minimum when using MP3 or

AAC. If you are concerned about the gap, please use

WAV or FLAC files.

Music files

MUTE

AUTO SURR ADV

ENTER

RETURN

AUDIO P.

TOP

HOME

TOOLS

BAND PTY

ENTER

RETURN

AUDIO P.

TOP

CLR

SB CH

CH SEL

Fav

RETURNHOME

SHIFT

BASS BASS

TRE TRE

BAND PTY

Extension Stream

MP3 (MPEG-1 Audio Layer 3)

.mp3aSampling frequency 32 kHz, 44.1 kHz, 48 kHz

Quantization bitrate 16 bit

Channel 2 ch

Bitrate 8 kbps to 320 kbps

VBR/CBR Supported/Supported

ENTER

Fav

RETURN

HOME

MENU BAND PTY

ENTER

Basic playback

a. MPEG Layer-3 audio decoding technology licensed from

Fraunhofer IIS and Thomson multimedia.

b. Files encoded using Windows Media Codec 9 may be playable

but some parts of the specification are not supported;

specifically, Pro, Lossless, Voice.

c. Uncompressed FLAC files are not supported. Pioneer does not

guarantee playback.

Photo files

Playing a MHL-compatible device

MHL (Mobile High-definition Link) is an interface standard for

transmitting digital signals with mobile devices. MHL can

carry high quality multi-channel audio data and full-HD video

formats.

The MHL-compatible device’s video signals are output from

the TV connected to the receiver, the audio signals are output

from the speakers connected to the receiver or TV.

Press



STANDBY/ON

to switch on the receiver and

your TV.

See Connecting a MHL-compatible device on page 25.

Press

MHL ROKU

on the remote control to switch the

receiver to the MHL.

Select and play the desired contents on the MHL-

compatible device.

Note

•

MHL-compatible devices can be operated with the

receiver’s remote control by pressing the remote control’s

MHL ROKU

button, but depending on the MHL-compatible

device being used, some buttons may not be operable.

•

To playback from a MHL-compatible device connected to

the receiver on a TV that is also connected to the receiver,

the power to the receiver must be turned on.

Enjoy Roku video streaming service

Connect the Roku Streaming Stick (sold separately) to the

MHL

terminal on the main device to enjoy video streaming.

Press



STANDBY/ON

to switch on the receiver and

your TV.

See Connecting a MHL-compatible device on page 25.

WAV (LPCM)

.wav Sampling frequency 32 kHz, 44.1 kHz, 48 kHz,

88.2 kHz, 96 kHz,

176.4 kHz, 192 kHz

Quantization bitrate 16 bit, 24 bit

Channel 2 ch

WMA (WMA2/7/8/9)

.wmabSampling frequency 32 kHz, 44.1 kHz, 48 kHz

Quantization bitrate 16 bit

Channel 2 ch

Bitrate 5 kbps to 320 kbps

VBR/CBR Supported/Supported

AAC (MPEG-4 AAC LC, MPEG-4 HE AAC)

.m4a

.aac

.3gp

.3g2

Sampling frequency 32 kHz, 44.1 kHz, 48 kHz

Quantization bitrate 16 bit

Channel 2 ch

Bitrate 16 kbps to 320 kbps

VBR/CBR Supported/Supported

FLAC

.flaccSampling frequency 32 kHz, 44.1 kHz, 48 kHz,

88.2 kHz, 96 kHz,

176.4 kHz, 192 kHz

Quantization bitrate 16 bit, 24 bit

Channel 2 ch

AIFF

.aif

.aiff

Sampling frequency 32 kHz, 44.1 kHz, 48 kHz,

88.2 kHz, 96 kHz, 176.4 kHz,

192 kHz

Quantization bitrate 16 bit, 24 bit

Channel 2 ch

Apple Lossless

.m4a

.mp4

Sampling frequency 32 kHz, 44.1 kHz, 48 kHz,

88.2 kHz, 96 kHz

Quantization bitrate 16 bit, 24 bit

Channel 2 ch

Extension Format

JPEG

.jpg Meeting the following conditions:

• Baseline JPEG format

• Y:Cb:Cr – 4:2:2

Basic playback

Press

MHL ROKU

on the remote control to switch the

receiver to the MHL.

Select the contents you want to play and playback.

Note

•

When the Roku Streaming Stick (sold separately) is

connected to the main device via the MHL terminal, and

the power switched on for the first time, a setup screen will

be displayed. Setup can be changed later on as well, see

Setup ROKU standby mode on page 56.

Bluetooth

ADAPTER for Wireless Enjoyment of

Music

Wireless music play

When the Bluetooth ADAPTER (Pioneer Model No. AS-BT100

or AS-BT200) is connected to this unit, a product equipped

with Bluetooth wireless technology (portable cell phone,

digital music player, etc.) can be used to listen to music

wirelessly. Also, by using a commercially available transmitter

supporting Bluetooth wireless technology, you can listen to

music on a device not equipped with Bluetooth wireless

technology. The AS-BT100 and AS-BT200 model supports

SCMS-T contents protection, so music can also be enjoyed on

devices equipped with SCMS-T type Bluetooth wireless

technology.

•

It must be necessary that the Bluetooth wireless technology

enabled device supports A2DP profiles.

Important

•

Pioneer does not guarantee proper connection and

operation of this unit with all Bluetooth wireless technology

enabled devices.

•

About one minute is required between turning the power

on and completion of startup.

Remote control operation

The remote control supplied with this unit allows you to play

and stop media, and perform other operations.

•

It must be necessary that the Bluetooth wireless technology

enabled device supports AVRCP profiles.

•

Remote control operations cannot be guaranteed for all

Bluetooth wireless technology enabled devices.

Pairing the

Bluetooth

ADAPTER and

Bluetooth

wireless technology device

“Pairing” must be done before you start playback of Bluetooth

wireless technology content using Bluetooth ADAPTER. Make

sure to perform pairing first time you operate the system or

any time pairing data is cleared. “Pairing” is the step

necessary to register Bluetooth wireless technology device to

enable Bluetooth communications. For more details, see also

the operating instructions of your Bluetooth wireless

technology device.

•

Pairing is required when you first use Bluetooth wireless

technology device and Bluetooth ADAPTER.

•

To enable Bluetooth communication, pairing should be

done with both of your system and Bluetooth wireless

technology device.

•

If the Bluetooth wireless technology device’s security code

is “0000”, there is no need to make the security code setting

on the receiver. Press

ADPT

to switch the ADAPTER

input, then conduct the pairing operation on the Bluetooth

wireless technology device. If pairing is successful, there is

no need to performing the pairing operation below.

•

When using the AS-BT200 only: This unit complies with

Bluetooth Specifications Ver. 2.1. When this unit and

another device equipped with Bluetooth wireless

technology both comply with Bluetooth Specification Ver.

2.1, pairing of the two may be possible without the need for

inputting a password.

Bluetooth wireless technology enabled device:

cell phone

Bluetooth wireless technology enabled device:

Digital music player

Device not equipped with Bluetooth wireless

technology: Digital music player + Bluetooth

audio transmitter (sold commercially)

Music data

Remote control

operation

Bluetooth®

ADAPTER

This receiver

Basic playback

In this case, a passcode may be displayed on this receiver

and on the device equipped with Bluetooth wireless

technology. If this happens, check that the same passcode

is displayed on this receiver and the device equipped with

Bluetooth wireless technology, then press

ENTER

. After

this, also perform the connection operation on the

Bluetooth device to be connected. If the passcode does not

match the code displayed on the Bluetooth device to be

connected, press

RETURN

to cancel pairing, then try

starting over.

Press

ADPT

to set the ADAPTER input, then conduct

the pairing operation on the Bluetooth wireless technology

device. If pairing is successful, there is no need to

performing the pairing operation below.

•

Pair one unit at a time.

•

When connecting this receiver by Bluetooth connections

with a device equipped with the Bluetooth function to listen

to music, do not connect any devices other than this

receiver by Bluetooth connection to the Bluetooth-equipped

device. If a Bluetooth connection is already established with

a device other than this receiver, disconnect the other

device before connecting this receiver.

Press

ADPT

to switch the receiver to ADAPTER input.

Press

TOP MENU

to select Bluetooth Setup.

Use

/

to select PIN, then press

ENTER

Use

/

to select one of PIN codes 0000, 1234 or 8888,

then press

ENTER

You can use any of 0000/1234/8888 PIN codes.

Bluetooth wireless technology device using any other PIN

code cannot be used with this system.

Switch on the Bluetooth wireless technology device

that you want to make pairing, place it near the system

and set it into the pairing mode.

Check to see that the Bluetooth ADAPTER is detected by

the Bluetooth wireless technology device.

When Bluetooth wireless technology device is connected:

Bluetooth wireless technology device name appears in

the receiver display.

•

The system can display alphanumeric characters only.

Other characters may not be displayed correctly.

When Bluetooth wireless technology device is not

connected:

WAITING appears in the receiver display. In this case,

perform the connection operation from the side of the

Bluetooth wireless technology device.

From the Bluetooth wireless technology device list,

select Bluetooth ADAPTER and enter the PIN code

selected in the step 4.

•

PIN code may in some case be referred to as

PASSKEY.

Listening to Music Contents of

Bluetooth

wireless

technology device with Your System

Press

ADPT

to switch the receiver to ADAPTER input.

Perform the connection operation from the side of the

Bluetooth wireless technology device to the Bluetooth

ADAPTER.

•

When the Bluetooth ADAPTER is not plugged into the

ADAPTER PORT terminal, NO ADP will be displayed if

ADAPTER input is selected.

Start playback of music contents stored in Bluetooth

wireless technology device.

This receiver’s remote control buttons can be used for

basic playback of files stored on the Bluetooth wireless

technology device.

•

Bluetooth wireless technology device should be

compatible with AVRCP profile.

•

Depending on Bluetooth wireless technology device

you use, operation may differ from what is shown in

the remote control buttons.

While listening to a source, press

RECEIVER

then press

ADV

repeatedly to select S.R AIR.

The Bluetooth® word mark and logos are registered

trademarks owned by Bluetooth SIG, Inc. and any use of such

marks by PIONEER HOME ELECTRONICS CORPORATION is

under license. Other trademarks and trade names are those

of their respective owners.

Note

•

With this receiver, when an iPod is connected or

disconnected while the music of a Bluetooth wireless

technology device is playing, the connection with the

Bluetooth wireless technology device may be canceled.

Fav

RETURN

HOME

MENU BAND PTY

Basic playback

Listening to the radio

The following steps show you how to tune in to FM and AM

radio broadcasts using the automatic (search) and manual

(step) tuning functions. Once you are tuned to a station you

can memorize the frequency for recall later—see Saving

station presets below for more on how to do this.

Press

TUNER

to select the tuner.

Use

BAND

to change the band (FM or AM), if necessary.

Each press switches the band between FM (stereo or

mono) and AM.

Tune to a station.

There are three ways to do this:

 Automatic tuning

To search for stations in the currently selected band,

press and hold

TUNE +/–

for about a second. The receiver

will start searching for the next station, stopping when it

has found one. Repeat to search for other stations.

 Manual tuning

To change the frequency one step at a time, press

TUNE +/–

 High speed tuning

Press and hold

TUNE +/–

for high speed tuning.

Improving FM sound

If the TUNE or ST indicators don’t light when tuning to an FM

station because the signal is weak, set the receiver to the

mono reception mode.



Press

BAND

to select FM MONO.

This should improve the sound quality and allow you to

enjoy the broadcast.

Saving station presets

If you often listen to a particular radio station, it’s convenient

to have the receiver store the frequency for easy recall

whenever you want to listen to that station. This saves the

effort of manually tuning in each time. This unit can memorize

up to 30 stations.

Tune to a station you want to memorize.

See Listening to the radio above for more on this.

Press

TOOLS

The display shows PRESET, then a blinking MEM and

station preset.

Press

PRESET +/–

to select the station preset you want.

You can also use the number buttons.

Press

ENTER

The preset number stop blinking and the receiver stores

the station.

Note

•

If the receiver is left disconnected from the AC power outlet

for over a month, the station memories will be lost and will

have to be reprogrammed.

•

Stations are stored in stereo. When the station is stored in

the FM MONO mode, it shows as ST when recalled.

Listening to station presets

You will need to have some presets stored to do this. See

Saving station presets above if you haven’t done this already.



Press

PRESET +/–

to select the station preset you want.

•

You can also use the number buttons on the remote

control to recall the station preset.

Naming preset stations

For easier identification, you can name all of your preset

stations.

Choose the station preset you want to name.

See Listening to station presets above for how to do this.

Press

TOOLS

twice.

The cursor at the first character position is blinking on

the display.

Input the name you want.

Choose a name up to eight characters long.

•

Use

/-

to select character position.

•

Use

/

to select characters.

•

The name is stored when

ENTER

is pressed.

Tip

•

To erase a station name, follow steps 1 and 2, and press

ENTER

while the display is blank. Press

TOOLS

while the

display is blank, to keep the previous name.

•

Once you have named a station preset, Press

DISP

to show

the name. When you want to return to the frequency

display, press

DISP

several times to show the frequency.

MUTE

AUTO SURR ADV

DVD

iPod

TUN

GAME

SAT

HDMI

MHL

NET

TUN

ENTER

Fav

RETURN

HOME

MENU BAND PTY

SLEEP

INPUTCTRL

DVD

iPod

TUN

GAME

SAT

HDMI

MHL

NET

S.SEL ECO

STANDBY/ON

RECEIVER SIGNAL SEL

SOURCE

TUN

ENTER

CLR

Fav

RETURN

AUDIO P.

TOP

HOME

TOOLS

BAND PTY

TOOLS

ENTER

Chapter

Listening to your system

Choosing the listening mode

This receiver offers a variety of listening modes to

accommodate playback of various audio formats. Choose one

according to your speaker environment or the source.



While listening to a source, press the listening mode

button repeatedly to select a listening mode you want.

•

The listening mode is shown on the display on the front

panel.

Important

•

The listening modes and many features described in this

section may not be available depending on the current

source, settings and status of the receiver.

Auto playback

The simplest, most direct listening option is the AUTO

SURROUND feature. With this, the receiver automatically

detects what kind of source you’re playing and selects

multichannel or stereo playback as necessary.

•

Press

AUTO

repeatedly until AUTO SURROUND shows

briefly in the display (it will then show the decoding or

playback format). Check the digital format indicators in the

display to see how the source is being processed.

Note

•

Stereo surround (matrix) formats are decoded accordingly

using NEO:6 CINEMA or DOLBY PLIIx MUSIC (see

Listening in surround sound below for more on these

decoding formats).

•

When listening to the ADAPTER input, the S.R AIR feature

is selected automatically (see Using the Advanced surround

on page 38 for more on this).

Listening in surround sound

Using this receiver, you can listen to any source in surround

sound. However, the options available will depend on your

speaker setup and the type of source you’re listening to.

•

If the source is Dolby Digital, DTS, or Dolby Surround

encoded, the proper decoding format will automatically be

selected and shows in the display.

When you select STEREO ALC (Auto Level Control stereo

mode), this unit equalizes playback sound levels if each sound

level varies with the music source recorded in a portable

audio player.

When you select STEREO, you will hear the source through

just the front left and right speakers (and possibly your

subwoofer depending on your speaker settings). Dolby Digital

and DTS multichannel sources are downmixed to stereo.

The following modes provide basic surround sound for stereo

and multichannel sources.

Explanatory notes

No: No connected / Yes: Connected / Two: Two speakers are

connected / –: Whether connected or no

MUTE

AUTO SURR ADV

TUN TV NET

AUDIO P.

TOP

TOOLS

AUTO SURR ADV

AUTO SURROUND

STREAM DIRECT

AUTO

ALC/

STANDARD SURR

SURR

Type of surround

modes Suitable sources

Surround back speaker(s)

Front height speakers

Two channel sources

STEREO ALC See above. – –

DOLBY PLIIx MOVIE Movie YesaNo

DOLBY PLII MOVIE No –

DOLBY PLIIx MUSICbMusic YesaNo

DOLBY PLII MUSICbNo –

DOLBY PLIIx GAME Video games YesaNo

DOLBY PLII GAME No –

DOLBY PLIIz HEIGHT

cMovie/Music No Yes

NEO:6 CINEMAdMovie – –

NEO:6 MUSICdMusic – –

DOLBY PRO LOGIC Old movies – –

Straight DecodeeNo additional effects No –

STEREOfSee above. – –

Multichannel sources

STEREO ALC See above. – –

DOLBY PLIIx MOVIE Movie Two No

DOLBY PLIIx MUSICbMusic Yes No

DOLBY DIGITAL EX Movie/Music Yes No

DTS-ES Movie/Music Yes No

DTS NEO:6 Movie/Music Yes No

DOLBY PLIIz HEIGHT Movie/Music No Yes

Straight DecodeeNo additional effects – –

STEREOfSee above. – –

Listening to your system

a. If surround back channel processing (Using surround back

channel processing below) is switched off, or the surround back

speakers are set to NO, DOLBY PLIIx becomes DOLBY PLII (5.1

channel sound).

b. You can also adjust the C.WIDTH, DIMEN., and PNRM. effect

(see Setting the Audio options on page 39).

c. You can also adjust the H.GAIN effect (see Setting the Audio

options on page 39).

d. You can also adjust the C.IMG effect (see Setting the Audio

options on page 39).

e. Cannot be selected when the Speaker System is set to Surr.

Back (see The Speaker System setting on page 57).

f. The audio is heard with your surround settings and you can still

use the Midnight, Loudness, Phase Control, Sound Retriever

and Tone functions.

Note

•

In modes that give 6.1 channel sound, the same signal is

heard from both surround back speakers.

Using the Advanced surround

The Advanced surround feature creates a variety of surround

effects. Try different modes with various soundtracks to see

which you like.

Note

•

During ECO mode, the brightness switches between 2

levels. If the dimmest level is selected, DIMMER will be

shown on the display. (Mode other than ECO: 4 levels, ECO

mode: 2 levels)

•

ECO MODE will switch OFF automatically when switched

to other listening modes (Advanced surround mode and

Auto surround mode).

Using Stream Direct

Use the Stream Direct modes when you want to hear the

truest possible reproduction of a source. All unnecessary

signal processing is bypassed.

Using the Sound Retriever

When audio data is removed during the compression

process, sound quality often suffers from an uneven sound

image. The Sound Retriever feature employs new DSP

technology that helps bring CD quality sound back to

compressed 2-channel audio by restoring sound pressure

and smoothing jagged artifacts left over after compression.

(see Setting the Audio options on page 39).

Listening with Acoustic Calibration EQ

You can listen to sources using the Acoustic Calibration

Equalization set in Automatically setting up for surround

sound (MCACC) on page 27. Refer to these pages for more on

Acoustic Calibration Equalization.

(see Setting the Audio options on page 39).

Using surround back channel processing

You can have the receiver automatically use 6.1 or 7.1

decoding for 6.1 encoded sources (for example, Dolby Digital

EX or DTS-ES), or you can choose to always use 6.1 or 7.1

decoding (for example, with 5.1 encoded material). With 5.1

encoded sources, a surround back channel will be generated,

but the material may sound better in the 5.1 format for which

it was originally encoded (in which case, you can simply

switch surround back channel processing off).

ACTION Designed for action movies with dynamic

soundtracks.

DRAMA Designed for movies with lots of dialog.

ADVANCED GAME Suitable for video games.

SPORTS Suitable for sports programs.

CLASSICAL Gives a large concert hall-type sound.

ROCK/POP Creates a live concert sound for rock and/or

pop music.

EXT.STEREO Gives multichannel sound to a stereo

source, using all of your speakers.

ECO MODE 1 Cut back on power consumption. Suitable

for contents that are mainly high level

(mainly music).

ECO MODE 2 Cut back on even more power consumption

than ECO MODE 1. Suitable for contents

with wider dynamic range (mainly movies).

ADVANCED

SURROUND

ADV

F.S.S.ADVANCE

(Front Stage

Surround

ADVANCE)

Allows you to create natural surround

sound effects using just the front speakers

and the subwoofer.

Use to provide a rich surround sound effect

directed to the center of where the front left

and right speakers sound projection area

converges.

S.R AIR (Sound

Retriever AIR)

Suitable for listening to the sound from a

Bluetooth wireless technology device.

The S.R AIR listening mode can only

selected when the ADAPTER input.

PHONES SURR When listening through headphones, you

can still get the effect of overall surround.

AUTO SURROUND See Auto playback on page 37.

Front left

speaker

Front right

speaker

AUTO SURROUND

STREAM DIRECT

AUTO

DIRECT Sources are heard according to the settings

made in the Manual SP Setup (speaker

setting, channel level, speaker distance), as

well as with dual mono settings. You will

hear sources according to the number of

channels in the signal.

Phase Control, Acoustic Calibration EQ,

Sound Delay, Auto Delay, LFE Attenuate

and Center image functions are available.

PURE DIRECT Analog and PCM sources are heard without

any digital processing.

Listening to your system

•

With a 7.1-channel surround system, audio signals that

have undergone matrix decoding processing through

surround back channel processing to which the Up Mix

function is added are output from the surround back

speakers.



Press

SB CH

repeatedly to cycle the surround back

channel options.

Each press cycles through the options as follows:

•

SB ON – Matrix decoding processing for generating

the surround back component from the surround

component is turned on.

•

SB AUTO – Matrix decoding processing for generating

the surround back component from the surround

component is switched automatically. Matrix

decoding processing is only performed when surround

back channel signals are detected in the input signals.

•

SB OFF – Matrix decoding processing for generating

the surround back component from the surround

component is turned off.

Setting the Up Mix function

In a 7.1-channel surround system with surround speakers

placed directly at the sides of the listening position, the

surround sound of 5.1-channel sources is heard from the side.

The Up Mix function mixes the sound of the surround

speakers with the surround back speakers so that the

surround sound is heard from diagonally to the rear as it

should be.

•

Using the Up Mix function is effective when the speakers in

the 7.1-channel surround system are set up as

recommended in the example on page 14.

•

Depending on the positions of the speakers and the sound

source, in some cases it may not be possible to achieve

good results. In this case, set the setting to OFF.

Switch the receiver into standby.

While holding down

PRESET

on the front panel, and

hold the



STANDBY/ON

for about two seconds.

UP MIX: OFF appears and the Up Mix function turns off.

If you want to turn this function on, perform steps 1 and

2 again.

•

When set to ON, the (Up Mix) indicator on the front

panel lights.

Note

•

Set to ON regardless of this setting when playing DTS-HD

signals.

•

May automatically be set to OFF even when set to ON,

depending on the input signal and listening mode.

•

If the Network Standby is set to ON or Standby Through

is not set to OFF, you may not be able to set the Up Mix

function.

•

HDMI Control should also be set to OFF, not ON.

Setting the Audio options

There are a number of additional sound settings you can

make using the AUDIO PARAMETER menu. The defaults, if

not stated, are listed in bold.

Important

•

Note that if a setting doesn’t appear in the AUDIO

PARAMETER menu, it is unavailable due to the current

source, settings and status of the receiver.

Press

RECEIVER

, then press

AUDIO P.

Use

/

to select the setting you want to adjust.

Depending on the current status/mode of the receiver,

certain options may not be able to be selected. Check the

table below for notes on this.

Use

/-

to set it as necessary.

See the table below for the options available for each

setting.

Press

RETURN

to confirm and exit the menu.

CLR

SB CH

CH SEL

SP-A/B

RECEIVER

SHIFT

BASS BASS

TRE TRE

SB CH

L R

SL SR

SBL SBR SBL SBR

L R

SL SR

UP MIX OFF UP MIX ON

SLEEP

INPUTCTRL

DVD

iPod

GAME

SAT

HDMI

MHL

S.SEL ECO

STANDBY/ON

RECEIVER SIGNAL SEL

SOURCE

RECEIVER

CTRL

MUTE

AUTO SURR ADV

ENTER

Fav

RETURN

AUDIO P.

TOP

HOME

TOOLS

BAND PTY

ENTER

RETURN

AUDIO P.

TOP

Listening to your system

a. The default setting when the iPod/USB, ADAPTER,

NETRADIO, PANDORA, M.SERVER or FAVORITE input is

selected is ON.

b. This setting works only with dual mono encoded Dolby Digital

and DTS soundtracks.

c. The initial set AUTO is only available for Dolby TrueHD signals.

Select MAX or MID for signals other than Dolby TrueHD.

d. You shouldn’t have any problems using this with most SACD

discs, but if the sound distorts, it is best to switch the gain

setting back to 0 dB.

e. This feature is only available when the connected display

supports the automatic audio/video synchronizing capability

(‘lip-sync’) for HDMI. If you find the automatically set delay time

unsuitable, set A.DLY to OFF and adjust the delay time

manually. For more details about the lip-sync feature of your

display, contact the manufacturer directly.

Setting/What it does Option(s)

EQ (Acoustic Calibration EQ)

Switches on/off the effect of Acoustic

Calibration EQ.

OFF

S.DELAY (Sound Delay)

Some monitors have a slight delay when

showing video, so the soundtrack will be

slightly out of sync with the picture. By adding

a bit of delay, you can adjust the sound to

match the presentation of the video.

0 to 500 ms (1

step : 5 ms)

Default: 0

MIDNIGHT/LOUDNESS

The MIDNIGHT allows you to hear effective

surround sound of movies at low volumes.

The LOUDNESS is used to get good bass and

treble from music sources at low volumes.

M/L OFF

MIDNIGHT

LOUDNESS

S.RTV (Sound Retriever)

Switches ON/OFF the effect of Sound

Retriever.

OFFa

DUAL MONOb

Specifies how dual mono encoded Dolby

Digital soundtracks should be played.

CH1 – Channel 1

is heard only

CH2 – Channel 2

is heard only

CH1 CH2 – Both

channels heard

from front

speakers

F.PCM (Fixed PCM)

This is useful if you find there is a slight delay

before OFF recognizes the PCM signal on a

CD, for instance.

When ON is selected, noise may be output

during playback of non-PCM sources. Please

select another input signal if this is a problem.

OFF

DRC (Dynamic Range Control)

Adjusts the level of dynamic range for movie

soundtracks optimized for Dolby Digital, DTS,

Dolby Digital Plus, Dolby TrueHD, DTS-HD

and DTS-HD Master Audio (you may need to

use this feature when listening to surround

sound at low volumes).

AUTOc

MAX

MID

OFF

LFE ATT (LFE Attenuate)

Some Dolby Digital and DTS audio sources

include ultra-low bass tones. Set the LFE

attenuator as necessary to prevent the ultra-

low bass tones from distorting the sound from

the speakers.

The LFE is not limited when set to 0 dB, which

is the recommended value. When set to –15

dB, the LFE is limited by the respective

degree. When OFF is selected, no sound is

output from the LFE channel.

0 (0 dB)

5 (–5 dB)

10 (–10 dB)

15 (–15 dB)

20 (–20 dB)

** (OFF)

SACD G. (SACD Gain)d

Brings out detail in SACDs by maximizing the

dynamic range (during digital processing).

0 (0 dB)

+6 (+6 dB)

HDMI (HDMI Audio)

Specifies the routing of the HDMI audio signal

out of this receiver (AMP) or through to a TV

(THRU). When THRU is selected, no sound is

output from this receiver.

The HDMI Audio setting cannot be switched

while performing synchronized amp mode

operations (page 59).

AMP

THRU

A.DLY (Auto Delay)e

This feature automatically corrects the audio-

to-video delay between components

connected with an HDMI cable. The audio

delay time is set depending on the operational

status of the display connected with an HDMI

cable. The video delay time is automatically

adjusted according to the audio delay time.

OFF

PHASE CTRL (Phase Control)f

Phase Control feature uses phase correction

measures to make sure your sound source

arrives at the listening position in phase,

preventing unwanted distortion and/or

coloring of the sound.

Phase Control technology provides coherent

sound reproduction through the use of phase

matching for an optimal sound image at your

listening position. The default setting is on

and we recommend leaving Phase Control

switched on for all sound sources.

OFF

Setting/What it does Option(s)

C.WIDTH (Center Width)g

(Applicable only when using a center speaker)

Spreads the center channel between the front

right and left speakers, making it sound wider

(higher settings) or narrower (lower settings).

0 to 7

Default: 3

DIMEN (Dimension)g

Adjusts the surround sound balance from

front to back, making the sound more distant

(minus settings), or more forward (positive

settings).

–3 to +3

Default: 0

PNRM. (Panorama)g

Extends the front stereo image to include

surround speakers for a ‘wraparound’ effect.

OFF

C.IMG (Center Image)h

(Applicable only when using a center speaker)

Adjust the center image to create a wider

stereo effect with vocals. Adjust the effect

from 0 (all center channel sent to front right

and left speakers) to 10 (center channel sent

to the center speaker only).

0 to 10 Default: 3

(NEO:6 MUSIC),

10 (NEO:6

CINEMA)

H.GAIN (Height Gain)

Adjusts the output from the front height

speaker when listening in DOLBY PLIIz

HEIGHT mode. If set to H, the sound from the

top will be more emphasized.

L (Low)

M (Mid)

H (High)

Setting/What it does Option(s)

Listening to your system

f. Phase matching is a very important factor in achieving proper

sound reproduction. If two waveforms are ‘in phase’, they crest

and trough together, resulting in increased amplitude, clarity

and presence of the sound signal. If a crest of a wave meets a

trough, then the sound will be ‘out of phase’ and an unreliable

sound image will be produced.

If your subwoofer has a phase control switch, set it to the plus

(+) sign (or 0°). However, the effect you can actually feel when

Phase Control is set to ON on this receiver depends on the type

of your subwoofer. Set your subwoofer to maximize the effect.

It is also recommended you try changing the orientation or the

place of your subwoofer.

Set the built-in lowpass filter switch of your subwoofer to OFF.

If this cannot be done on your subwoofer, set the cutoff

frequency to a higher value.

If the speaker distance is not properly set, you may not have a

maximized Phase Control effect.

The Phase Control mode cannot be set to ON in the following

cases:

– When the PURE DIRECT mode is switched on.

– When the headphones are connected.

g. Only available with 2-channel sources in DOLBY PLII MUSIC

mode.

h. Only when listening to 2-channel sources in NEO:6 CINEMA

and NEO:6 MUSIC mode.

Chapter

Playback with NETWORK features

Introduction

This receiver is equipped with the LAN terminal and you can

enjoy the following features by connecting your components

to these terminals.

Listening to Internet radio stations

You can select and listen to your favorite Internet radio station

from the list of Internet radio stations created, edited, and

managed by the vTuner database service exclusively for use

with the Pioneer products.

See Playback with Network functions on page 43 and Listening

to Internet radio stations on page 44.

Playback the music files stored in PCs

You can playback a lot of musics stored in your PCs using this

unit.

•

Besides a PC, you can also play back audio files stored on

your other components with the built-in media server

function based on DLNA 1.0 or DLNA 1.5 framework and

protocols (i.e. network-capable hard disks and audio

systems).

See Playback with Network functions on page 43 and Playing

back audio files stored on components on the network on

page 45.

Listening to Pandora

See Listening to Pandora Internet Radio on page 44.

Using the Spotify audio stream playback function

See About the Spotify audio stream playback function on

page 45.

Note

•

To listen to Internet radio stations, you must sign a contract

with an ISP (Internet Service Provider) beforehand.

•

Photo or video files cannot be played back.

•

With Windows Media Player 11 or Windows Media Player

12, you cannot play back copyrighted audio files on this

receiver.

About playable DLNA network devices

This unit allows you to play music on media servers connected

on an identical Local Area Network (LAN) as the receiver. This

unit allows for the playing of files stored on the following

devices:

•

PCs running Microsoft Windows Vista or XP with Windows

Media Player 11 installed

•

PCs running Microsoft Windows 7 or 8 with Windows

Media Player 12 installed

•

DLNA-compatible digital media servers (on PCs or other

components)

Files stored in a PC or DMS (Digital Media Server) as

described above can be played via command from an external

Digital Media Controller (DMC). Devices controlled by this

DMC to play files are called DMRs (Digital Media Renderers).

This receiver supports this DMR function. When in the DMR

mode, such operations as playing and stopping files can be

performed from the external controller. Volume adjustment

and the muting control are also possible.

•

Depending on the external controller being used, playback

may be interrupted when the volume is adjusted from the

controller. In this case, adjust the volume from the receiver

or remote control.

Using AirPlay on iPod touch, iPhone, iPad, and

iTunes

AirPlay works with iPhone, iPad, and iPod touch with iOS

4.3.3 or later, Mac with OS X Mountain Lion, and Mac and PC

with iTunes 10.2.2 or later.

To use AirPlay, select your receiver on your iPod touch,

iPhone, iPad or in iTunes. *1

The receiver’s input will switch automatically to AirPlay when

AirPlay is in use. *2

The following operations can be performed when in AirPlay

mode:

•

Adjustment of the receiver’s volume from iPod touch,

iPhone, iPad or iTunes.

•

Pause/resume, next/previous track, and shuffle/repeat

from the remote control of the receiver. (Press

NET

switch the remote control to the network operation mode.)

*1: For more information, see the Apple website (http://

www.apple.com).

*2: The receiver’s power automatically turns on when

Network Standby is set to ON (page 56).

Note

•

A network environment is required to use AirPlay.

•

AirPlay provided on this receiver has been developed and

tested based on the software versions for the iPod, iPhone,

iPad and the software versions for iTunes that are indicated

on the Pioneer website. AirPlay may not be compatible with

iPod, iPhone, iPad or iTunes software versions other than

those indicated on the Pioneer website.

About the DHCP server function

To play back audio files stored on components on the network

or listen to Internet radio stations, you must turn on the DHCP

server function of your router. In case your router does not

have the built-in DHCP server function, it is necessary to set

up the network manually. Otherwise, you cannot play back

audio files stored on components on the network or listen to

Internet radio stations. See The Network Setup menu on

page 46 for more on this.

Authorizing this receiver

This receiver must be authorized to enable playback. This

happens automatically when the receiver makes a connection

over the network to the PC. If not, please authorize this

receiver manually on the PC. The authorization (or

permission) method for access varies depending on the type

of server currently being connected. For more information on

authorizing this receiver, refer to the instruction manual of

your server.

Playback with NETWORK features

About HTC Connect

This receiver features “HTC Connect”, a simple way to enjoy

music content from your HTC Connect certified smart phone.

HTC Connect music streaming provided on this product

has been developed based on interoperability testing as

defined by the HTC Connect Certification program with

the HTC Connect-compatible smartphones.

Music Navigation via the music progress bar is not

currently supported with HTC Connect.

Third party music applications (those other than HTC’s

pre-installed “Music” app) have not been tested for

compatibility and may not work. HTC Connect has been

tested with MP3, AAC, WMA and WAV encoding

formats. Other formats may not be compatible.

High network congestion may interfere with the

operation of HTC Connect.

HTC Connect Certified Smartphones

The HTC Connect-compatible smartphones, Please check

Pioneer website for up to date information about compatible

devices and audio format support.

http://www.pioneerelectronics.com/htc (for USA)

http://www.pioneerelectronics.ca/htc (for Canada)

Specifications and design subject to modification without

notice.

HTC, HTC Connect and the HTC Connect logo are trademarks

of HTC Corporation.

Playback with Network functions

Important

•

In case a domain is configured in a Windows network

environment, you cannot access a PC on the network while

you are logged onto the domain. Instead of logging onto the

domain, log onto the local machine.

•

There are cases where the time elapsed may not be

correctly displayed.

•

About one minute is required between turning the power

on and completion of startup.

Press

NET

repeatedly to select the category you want to

play back.

It may take several seconds for this receiver to access the

network.

Select a category from the following list:

•

NETRADIO – Internet radio

When NETRADIO is selected, the radio station that

was playing last time is played.

•

PANDORA – Internet radio that supports Pandora

•

M.SERVER – Server components on the network

(Media server)

•

FAVORITE – Favorite songs currently being registered

Depending on the selected category, the names of

folders, files, and Internet radio stations are displayed.

Use

/

to select the folder, music files or Internet

radio station to play back, and then press

ENTER

Press

/

to scroll up and down the list and select the

desired item. When you press

ENTER

, playback starts

with the playback screen being displayed for the selected

item. To return to the list screen, press

RETURN

When the list screen is displayed from the playback

screen, the playback screen reappears automatically if

no operation is performed for 180 seconds while the list

screen is displayed. Will return to playback screen even if

DISP

button is pressed.

Only audio files with the mark can be played. In case

of the folders with the mark, use

/

and

ENTER

select the desired folder and audio files.

•

When  or  is pressed at the list screen, the

page switches.

Repeat step 2 to play back the desired song.

For detailed operating instructions, refer to the section

shown below.

•

Internet radio stations – See Listening to Internet radio

stations on page 44.

•

Pandora – See Listening to Pandora Internet Radio on

page 44.

•

Media server – See Playing back audio files stored on

components on the network on page 45.

•

Favorites – See Playing back your favorite songs on

page 45.

Basic playback controls

You can perform the following operations with the remote

control of this receiver. Note that some buttons are not

available for operation depending on the category currently

being played back.



Press

NET

to switch the remote control to the

NETRADIO, PANDORA, M.SERVER or FAVORITE

operation mode.

Note

•

When selecting input for M.SERVER and FAVORITE,

depending on the server or file:

the  button will not operate.

the   button will not operate or will act identical to

the   button.

MUTE

AUTO SURR ADV

TUN TV NET

ENTER

RETURN

AUDIO P.

TOP

HOME

TOOLS

BAND PTY

AUDIO P.

TOP

TOOLS

ENTER

RETURN

CLR

SB CH

CH SEL

SP-A/B

Fav

RETURN

HOME

SHIFT

BASS BASS

TRE TRE

BAND PTY

Fav

CLR

Playback with NETWORK features

•

If the

TOOLS

button is pressed for the list displayed screen

when selecting input for M.SERVER, one can realign the

displayed title alphabetically or the track No.

Listening to Internet radio stations

Internet radio is an audio broadcasting service transmitted via

the Internet. There are a large number of Internet radio

stations broadcasting a variety of services from every corner

of the world. Some are hosted, managed, and broadcast by

private individuals while others are by the corresponding

traditional terrestrial radio stations or radio networks.

Whereas terrestrial, or OTA (over-the-air), radio stations are

geographically restricted on the range of radio waves

broadcast from a transmitter through the air, Internet radio

stations are accessible from anywhere in the world, as long as

there is a connection to the Internet, as services are not

transmitted through the air but are delivered over the World

Wide Web. On this receiver you can select Internet radio

stations by genre as well as by region.

Depending on the Internet line conditions, the sound may not

be smooth when playing Internet radio.

About list of Internet radio

The list of Internet radio stations on this receiver is created,

edited, and managed by the vTuner database service

exclusively for use with this receiver. For details about vTuner,

see vTuner on page 51.

Saving and retrieving Internet radio stations

You can easily save and retrieve saved Internet radio stations.

See Playing back your favorite songs on page 45 for more on

this.

•

To listen to Internet radio stations, you must have high-

speed broadband Internet access. With a 56 K or ISDN

modem, you may not enjoy the full benefits of Internet

radio.

•

The port number varies depending on the Internet radio

station. Check the firewall settings.

•

A list of Internet radio stations provided by the vTuner

database service is subject to change or deletion without

notice due to various reasons.

•

Broadcasts may be stopped or interrupted depending on

the Internet radio station. In this case, you cannot listen to

a radio station selected from the list of Internet radio

stations.

Registering broadcast stations not on the vTuner list

from the special Pioneer site

With the receiver, broadcast stations not included on the list

of station distributed by vTuner can be registered and played.

Check the access code required for registration on the

receiver, use this access code to access the special Pioneer

Internet radio site and register the desired broadcast stations

in your favorites. The address of the special Pioneer Internet

radio site is:

http://www.radio-pioneer.com

Display the Internet Radio list screen.

To display the Internet Radio list screen, perform step 1 at

Playback with Network functions on page 43.

Use

/

to select ‘Help’, then press

ENTER

Use

/

to select ‘Get access code’, then press

ENTER

The access code required for registration on the special

Pioneer Internet radio site is displayed. Make a memo of

this address.

The following can be checked on the Help screen:

•

Get access code – The access code required for

registration on the special Pioneer Internet radio site is

displayed.

•

Show Your WebID/PW – After registering on the

special Pioneer Internet radio site, the registered ID

and password are displayed.

•

Reset Your WebID/PW – Resets all the information

registered on the special Pioneer Internet radio site.

When reset, all the registered broadcast stations are

also cleared. If you want to listen to the same stations,

re-register after resetting.

Access the special Pioneer Internet radio site from your

computer and perform the registration process.

http://www.radio-pioneer.com

Access the above site and use the access code in step 3

to perform user registration, following the instructions on

the screen.

favorites, following the instructions on the computer’s

screen.

Both broadcast stations not on the vTuner list and

stations on the vTuner list can be registered. In this case

they are registered on the receiver as favorite broadcast

stations and can be played.

Listening to Pandora Internet Radio

Pandora is personalized internet radio that is designed to help

you discover new music you’ll love mixed in with music you

already know.

For details, check the website: http://www.pandora.com

•

You must have a registered account in order to listen to

songs using Pandora Internet Radio.

Select PANDORA, then follow the instructions on the

screen to make the account settings.

•

As of December 2012, the Pandora service is only offered in

the United States.

•

Some functions may be changed at Pandora’s discretion.

Note

•

When disposing of the product, we recommend you reset it

to delete the data. See Resetting the main unit on page 66.

Pandora®, the leading internet radio service, gives people

music they love anytime, anywhere, through personalized radio

stations.

Character entry operation using the virtual keyboard

Press

TOOLS

to switch to virtual keyboard operation

mode.

Use the directional keys

///-

to select the

character/symbols and press

ENTER

Repeat 2 above until character entry is finished and

select OK from the virtual keyboard and press

ENTER

•

To exit character entry using the virtual keyboard,

press

TOOLS

Playback with NETWORK features

About the Spotify audio stream playback

function

Spotify is a music streaming distribution service managed

and operated by Spotify Ltd. and distributing music over the

Internet.

Spotify audio streams can be enjoyed using this unit and your

smartphone or other mobile device.

Preparations (1) Installing the Spotify application

on mobile devices and registering a Spotify

Premium account

Important

•

The Spotify application must be installed on mobile devices

and you must have registered a Spotify Premium account

(for a charge) in order to use the Spotify audio stream

playback function on this unit.

For registration procedures, see the Spotify website.

http://www.spotify.com/

http://www.spotify.com/connect

For information on the countries and regions where Spotify

services can be used, see the website below.

http://www.spotify.com/

Spotify functions may be changed without notice.

An Internet connection is required on the mobile device in

order to use the Spotify application. Using the mobile

telephone line for the Internet connection tends to lead to

high packet communication charges, so we recommend

subscribing to a fixed packet rate plan. For details, contact

your mobile telephone operator.

Preparations (2) Connecting this unit to the

network

•

Connect this unit to the network and also to the Internet.

For instructions on connecting, see this unit’s operating

instructions.

•

Connect the mobile device by Wi-Fi to the wireless LAN

router of the same network as the one to which this unit is

connected. For instructions on connecting, see the

operating instructions of the mobile device and the

wireless LAN router.

In order to use the Spotify audio stream playback

function from the Spotify application

To use the Spotify audio stream playback function, select this

unit on the Spotify application.

When Spotify audio streaming starts, this unit’s input

automatically switches to Spotify.

CAUTION

•

Even if you are away from home, if you start Spotify audio

streaming to play music on your mobile device and this unit

is selected, the sound will be output from this unit.

Depending on the volume level, the output may be loud, so

be sure to check the audio output selection carefully before

starting audio streaming. In addition, if you accidentally

select this unit and play the sound on it, switch the audio

output selection to the mobile device.

Note

•

A separate contract with/payment to an Internet service

provider is required to use the Spotify audio stream

playback function.

•

This unit’s name is displayed as the playback device on the

Spotify application. Also, this unit’s name can be changed

at “Friendly Name” in the network settings.

•

When this unit is selected with the Spotify application, the

account information is registered on this unit as well.

When disposing of this unit, reset this unit’s settings in

order to delete the account information registered on this

unit. For instructions on resetting, see this unit’s operating

instructions.

Playing back audio files stored on components on

the network

This unit allows you to play music on media servers connected

on an identical Local Area Network (LAN) as the receiver. This

unit allows for the playing of files stored on the following

devices:

•

PCs running Microsoft Windows Vista or XP with Windows

Media Player 11 installed

•

PCs running Microsoft Windows 7 or 8 with Windows

Media Player 12 installed

•

DLNA-compatible digital media servers (on PCs or other

components)

Playing back your favorite songs

Up to 64 favorite tracks on the media server and/or Internet

radio stations can be registered in the Favorites folder. Note

that only the audio files stored on components on the network

can be registered.

Registering and deleting audio files and Internet

radio stations in and from the Favorites folder

Press

NET

to switch the remote control to the M.SERVER

or NETRADIO operation mode.

With the track or Internet radio station you want to

+Fav

The selected song or Internet radio station is then

registered in the Favorite.

Note

•

To delete a registered song, select the Favorites folder,

select the song you want to delete from the folder, and

press

CLR

. The selected song is then deleted from the

Favorites folder.

Playback with NETWORK features

The Network Setup menu

Setting up the network to listen to Internet radio on this

receiver.

Press

NET

Press

HOME MENU

Network Setup menu appears on your TV. Use

///

and

ENTER

on the remote control to navigate through

the screens and select menu items. Press

RETURN

exit the current menu.

•

Press

HOME MENU

at any time to exit the Network

Setup menu.

Select the setting you want to adjust.

•

Network Configuration

IP Address, Proxy – Sets up the IP address/Proxy of

this receiver (see below).

Friendly Name – The name of the receiver displayed

on a computer or other device connected to the

network can be changed (see below).

Parental Lock – Restricts usage of network

functions (page 47).

•

Language – Language can be set the NETWORK

function OSD screen (page 47).

•

Firmware Update – Use to update the receiver’s

firmware and check the version (page 47).

•

Factory Reset – Use to reset all network connection

settings to their initial, factory-setting condition

(page 49).

•

System Info – You can check the network settings of

this receiver (page 49).

Network Configuration

IP address/Proxy setting

In case the router connected to the LAN terminal on this

receiver is a broadband router (with a built-in DHCP server

function), simply turn on the DHCP server function, and you

will not need to set up the network manually. You must set up

the network as described below only when you have

connected this receiver to a broadband router without a

DHCP server function. Before you set up the network, consult

with your ISP or the network manager for the required

settings. It is advised that you also refer to the operation

manual supplied with your network component.

•

IP Address

The IP address to be entered must be defined within the

following ranges. If the IP address defined is beyond the

following ranges, you cannot play back audio files stored on

components on the network or listen to Internet radio

stations.

Class A: 10.0.0.1 to 10.255.255.254

Class B: 172.16.0.1 to 172.31.255.254

Class C: 192.168.0.1 to 192.168.255.254

•

Subnet Mask

In case an xDSL modem or a terminal adapter is directly

connected to this receiver, enter the subnet mask provided

by your ISP on paper. In most cases, enter 255.255.255.0.

•

Default Gateway

In case a gateway (router) is connected to this receiver,

enter the corresponding IP address.

•

Primary DNS Server/Secondary DNS Server

In case there is only one DNS server address provided by

your ISP on paper, enter it in the “Primary DNS Server”

field. In case there are more than two DNS server

addresses, enter “Secondary DNS Server” in the other

DNS server address field.

•

Proxy Hostname/Proxy Port

This setting is required when you connect this receiver to

the Internet via a proxy server. Enter the IP address of your

proxy server in the “Proxy Hostname” field. Also, enter the

port number of your proxy server in the “Proxy Port” field.

Select ‘Network Configuration’ from the Network

Setup menu.

Select ‘IP Address, Proxy’ from the Network

Configuration menu.

Select the DHCP setting you want.

When you select ON, the network is automatically set up,

and you do not need to follow Steps 4. Proceed with Step

If there is no DHCP server on the network and you select

ON, this receiver will use its own Auto IP function to

determine the IP address.

•

The IP address determined by the Auto IP function is

169.254.X.X. You cannot listen to an Internet radio

station if the IP address is set for the Auto IP function.

Enter the IP Address, Subnet Mask, Default Gateway,

Primary DNS Server and Secondary DNS Server.

Press

/

to select a number and

/-

to move the

cursor.

Select ‘OFF’ or ‘ON’ for the Enable Proxy Server setting

to deactivate or activate the proxy server.

In case you select OFF, proceed with Step 8. In case you

select ON, on the other hand, proceed with Step 6.

Enter the address of your proxy server or the domain

name.

Use

/

to select a character,

/-

to set the position,

and

ENTER

to confirm your selection.

Enter the port number of your proxy server.

Use

/

to select a character,

/-

to set the position,

and

ENTER

to confirm your selection.

Select ‘OK’ to confirm the IP Address/Proxy setup.

Playback with NETWORK features

Friendly Name

Select ‘Network Configuration’ from the Network

Setup menu.

Select ‘Friendly Name’ from the Network Configuration

menu.

Select ‘Edit Name’ then select ‘Rename’.

If after changing the name you want to restore the name

to the default, select Default.

Input the name you want.

Use

/

to select a character,

/-

to set the position,

and

ENTER

to confirm your selection.

Parental Lock

Set restrictions for using Internet services. Also set the

password accompanying the usage restrictions.

•

Upon shipment from the factory, the password is set to

“0000”.

Select ‘Network Configuration’ from the Network

Setup menu.

Select ‘Parental Lock’ from the Network Configuration

menu.

Input the password.

Use

/

to select a character,

/-

to set the position,

and

ENTER

to confirm your selection.

Specify whether to turn Parental Lock on or off.

•

OFF – Internet services are not restricted.

•

ON – Internet services are restricted.

If you want to change the password, select ‘Change

Password’.

In this case, the procedure returns to step 3.

Language

Language can be set on the NETWORK function OSD screen.

Select ‘Language’ from the Network Setup menu.

Select the language you want.

When you’re finished, press

RETURN

You return to the Network Setup menu.

Firmware Update

Use this procedure to update the receiver’s firmware.

If an update file does not exist in the Pioneer’s website,

updating the firmware for the receiver is not necessary.

Updating via a USB memory device is performed by

downloading the update file from a computer, reading this file

onto a USB memory device then inserting this USB memory

device into the USB port on the receiver’s front panel. With

this procedure, the USB memory device containing the

update file must first be inserted into the USB port on the

receiver’s front panel.

•

If an update file is provided on the Pioneer website,

download it onto your computer. When downloading an

update file from the Pioneer website onto your computer,

the file will be in ZIP format. Unzip the ZIP file before saving

it on the USB memory device. If there are any old

downloaded files or downloaded files for other models on

the USB memory device, delete them.

Important

•

DO NOT unplug the power cord during updating.

•

Do not disconnect the USB memory device during

updating.

•

Verify the firmware version of the receiver in the System

Info menu before updating and confirm that the firmware

in the USB memory device is a newer version.

•

Updating may reset the receiver’s settings to the initial,

factory-setting condition. Whether this is applicable to your

receiver can be confirmed at our Pioneer website.

Select ‘Firmware Update’ from the Network Setup

menu.

The receiver checks whether the USB memory device

inserted into the USB port on the receiver’s front panel

contains updatable firmware.

To update, select ‘Start’.

When ‘Updating in progress, don’t unplug!’ is

displayed, select ‘Start’.

•

If ‘File Not Found’ is displayed, try the following:

No update file was found on the USB memory

device. Store the file in the USB memory device’s

root directory.

Try disconnecting then reconnecting the USB device

or storing the update file again. If the error still

occurs, try using a different USB memory device.

The firmware update will start. Please wait.

The OSD display will turn off during update and the words

‘UPDATE’ will flash on the front panel.

Will automatically restart after update is completed.

The screen will return automatically to the last selected

function.

•

If ‘FAIL’ or ‘SUB FAIL’ is displayed on the front panel

display, updating has failed. Try the following:

If ‘SUB FAIL’ is displayed, please wait for a while.

Update will start automatically. If update does not

resume or if ‘SUB FAIL’ is displayed again, try the

following.

Turn the receiver’s power off, then turn it back on

and try updating the firmware again.

Try disconnecting then reconnecting the USB device

or storing the update file again. If the error still

occurs, try using a different USB memory device.

Playback with NETWORK features

Network setting using Safari browser

Launch Safari on your computer.

Press Bookmark icon. Click Bonjour list (a), and then

select this receiver’s name (Friendly Name) (b) in

Bookmark.

If Bonjour list is not displayed, access the IP address

“http://(the receiver's IP address)” from Safari.

Select ‘Network Setup’.

Click IP, Proxy Setting.

Setup the network settings manually and then press

Apply.

Note

•

This setting for the network has been confirmed for Mac OS

X 10.7 and Safari 5.1.

Friendly Name setting using Safari browser

Launch Safari on your computer.

Press Bookmark icon. Click Bonjour list (a), and then

select this receiver’s name (Friendly Name) (b) in

Bookmark.

Select ‘Network Setup’.

Click Friendly Name.

Enter friendly name and then press Apply.

Note

•

This setting for the network has been confirmed for Mac OS

X 10.7 and Safari 5.1.

Firmware update using Safari browser

Launch Safari on your computer.

Press Bookmark icon. Click Bonjour list (a), and then

select this receiver’s name (Friendly Name) (b) in

Bookmark.

Select ‘Network Setup’.

VSX-44

Network Setup

VSX-44

Network Setup

Playback with NETWORK features

Click Firmware Update.

Press Start.

The firmware update prepare screen is displayed. If the

screen does not switch automatically, click Click here.

Browse the latest firmware on your computer (a) and

then press Upload (b).

The extension of the firmware is fw. Please select a file

that has the fw extension.

The confirmation screen is displayed. If you continue the

firmware update, press OK. Once the firmware update

process starts, you can't stop it. Wait until the file is

uploaded (about one minute may be required depending

on your LAN connection environment).

The firmware upload status screen is displayed.

“The upload process finished successfully.” will be shown

when the update is completed.

Unplug the power cord from the AC outlet after the

update is completed.

Factory Reset

Use to reset all network connection settings to their initial,

factory-setting condition.

Select ‘Factory Reset’ from the Network Setup menu.

Select ‘Start’.

Select ‘OK’ to confirm.

The screen will return automatically to the play screen.

System Information

The setting status of the following network-related items can

be checked.

•

IP Address – Check the IP address of this receiver.

•

MAC Address – Check the MAC address of this receiver.

•

Ver – Check the firmware version of this receiver.

Select ‘System Info’ from the Network Setup menu.

Display the setting status of the network-related items.

When you’re finished, press

RETURN

You return to the Network Setup menu.

Network Setup

Playback with NETWORK features

About network playback

The network playback function of this unit uses the following

technologies:

Windows Media Player

See Windows Media Player 11/Windows Media Player 12 on

page 51 for more on this.

DLNA

DLNA CERTIFIED™ Audio Player

The Digital Living Network Alliance (DLNA) is a cross-industry

organization of consumer electronics, computing industry

and mobile device companies. Digital Living provides

consumers with easy sharing of digital media through a wired

or wireless network in the home.

The DLNA certification logo makes it easy to find products

that comply with the DLNA Interoperability Guidelines. This

unit complies with DLNA Interoperability Guidelines v1.5.

When a PC running DLNA server software or other DLNA

compatible device is connected to this player, some setting

changes of software or other devices may be required. Please

refer to the operating instructions for the software or device

for more information.

DLNA™, the DLNA Logo and DLNA CERTIFIED™ are

trademarks, service marks, or certification marks of the Digital

Living Network Alliance.

Content playable over a network

•

Even when encoded in a compatible format, some files may

not play correctly.

•

Movie or Photo files cannot be played back.

•

There are cases where you cannot listen to an Internet radio

station even if the station can be selected from a list of

radio stations.

•

Some functions may not be supported depending on the

server type or version used.

•

Supported file formats vary by server. As such, files not

supported by your server are not displayed on this unit. For

more information check with the manufacturer of your

server.

Disclaimer for Third Party Content

ACCESS TO THIRD PARTY CONTENT SERVICES, INCLUDING

ALL ASSOCIATED FEATURES AND FUNCTIONALITIES, IS

PROVIDED “AS IS,” “AS AVAILABLE” AND AT THE USER’S

OWN RISK, WITHOUT WARRANTY OF ANY KIND. PIONEER

DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, IN

CONNECTION WITH ACCESS TO AND USE OF CONTENT

SERVICES THROUGH THIS DEVICE, INCLUDING WITHOUT

LIMITATION WARRANTIES OF MERCHANTABILITY,

SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR

PURPOSE, AND NON-INFRINGEMENT. PIONEER DOES NOT

GUARANTEE, REPRESENT, OR WARRANT THAT CONTENT

SERVICES WILL BE FREE FROM ERRORS, INTERRUPTION,

LOSS, CORRUPTION, ATTACK, VIRUSES, INTERFERENCE,

HACKING, OR OTHER SECURITY INTRUSION, AND PIONEER

DISCLAIMS ANY LIABILITY IN CONNECTION WITH THE

FOREGOING. PIONEER IS NOT LIABLE OR RESPONSIBLE

FOR ANY LOSS OR DAMAGE ARISING FROM ACCESS TO OR

USE OF CONTENT. NO ORAL OR WRITTEN INFORMATION

OR ADVICE GIVEN BY PIONEER OR ITS CUSTOMER

SERVICES REPRESENTATIVES WILL CREATE ANY SUCH

WARRANTY.

IN NO EVENT WILL PIONEER, ITS AFFILIATES, OR THEIR

RESPECTIVE OFFICERS, DIRECTORS, OR EMPLOYEES BE

LIABLE IN CONNECTION WITH YOUR USE OF THIRD PARTY

CONTENT SERVICES THROUGH THIS DEVICE FOR

PERSONAL INJURY OR SPECIAL, INCIDENTAL, INDIRECT

OR CONSEQUENTIAL DAMAGES OF ANY KIND, INCLUDING

WITHOUT LIMITATION DAMAGES FOR ATTORNEY’S FEES,

LOST DATA OR LOST PROFITS, REGARDLESS OF THE

THEORY OF LIABILITY AND WHETHER OR NOT ADVISED OF

THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL

PIONEER’S TOTAL LIABILITY TO YOU FOR ALL DAMAGES

ARISING FROM THE USE OR INABILITY TO USE THIRD

PARTY CONTENT SERVICES (OTHER THAN AS MAY BE

REQUIRED BY LAW IN CASES INVOLVING PERSONAL

INJURY) EXCEED $10.00. THE FOREGOING LIMITATIONS

WILL APPLY EVEN IF THE ABOVE REMEDY FAILS OF ITS

ESSENTIAL PURPOSE. IF ANY APPLICABLE AUTHORITY

HOLDS ANY PORTION OF THIS SECTION TO BE

UNENFORCEABLE, THEN LIABILITY WILL BE LIMITED TO

THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW.

About playback behavior over a network

•

Playback may stall when the PC is switched off or any

media files stored on it are deleted while playing content.

•

If there are problems within the network environment

(heavy network traffic, etc.) content may not be displayed or

played properly (playback may be interrupted or stalled).

For best performance, a 100BASE-TX connection between

player and PC is recommended.

•

If several clients are playing simultaneously, as the case

may be, playback is interrupted or stalled.

•

Depending on the security software installed on a

connected PC and the setting of such software, network

connection may be blocked.

Pioneer is not responsible for any malfunction of the player

and/or the NETWORK features due to communication error/

malfunctions associated with your network connection and/

or your PC, or other connected equipment. Please contact

your PC manufacturer or Internet service provider.

This product includes technology owned by Microsoft

Corporation and cannot be used or distributed without a license

from Microsoft Licensing, Inc.

Microsoft, Windows, Windows Media and Windows Vista are

either registered trademarks or trademarks of Microsoft

Corporation in the United States and/or other countries.

Playback with NETWORK features

Glossary

FLAC

FLAC (Free Lossless Audio Codec) is an audio format allows

lossless codec. Audio is compressed in FLAC without any loss

in quality. For more details about FLAC, visit the following

website: http://flac.sourceforge.net/

vTuner

vTuner is a paid online database service that allows you to

listen to radio and TV broadcasts on the Internet. vTuner lists

thousands of stations from over 100 different countries

around the globe. For more detail about vTuner, visit the

following website:

http://www.radio-pioneer.com

“This product is protected by certain intellectual property rights

of NEMS and BridgeCo. Use or distribution of such technology

outside of this product is prohibited without a license from

NEMS and BridgeCo or an authorized subsidiary.”

Windows Media

Windows Media is a multimedia framework for media

creation and distribution for Microsoft Windows. Windows

Media is either a registered trademark or trademark of

Microsoft Corporation in the U.S. and/or other countries. Use

an application licensed by Microsoft Corporation to author,

distribute, or play Windows Media formatted content. Using

an application unauthorized by Microsoft Corporation is

subject to malfunction.

Windows Media Player 11/Windows Media Player 12

Windows Media Player is software to deliver music, photos

and movies from a Microsoft Windows computer to home

stereo systems and TVs.

With this software, you can play back files stored on the PC

through various devices wherever you like in your home.

This software can be downloaded from Microsoft’s website.

•

Windows Media Player 11 (for Windows XP or Windows

Vista)

•

Windows Media Player 12 (for Windows 7 or 8)

For more information check the official Microsoft website.

About playable file formats

The NETWORK feature of this receiver supports the following

file formats. Note that some file formats are not available for

playback although they are listed as playable file formats.

Also, the compatibility of file formats varies depending on the

type of server. Check with your server to ensure the

compatibility of file formats supported by your server.

•

Internet radio playback may be affected by the Internet

communications environment, and in this case playback

may not be possible even with the file formats listed here.

•

With MP3, WAV, AAC, FLAC, AIFF and Apple Lossless files,

when music files with the same format, sampling

frequency, quantization bit number and number of

channels are played successively, they are played with no

gap.

Make sure the gap is at the minimum when using MP3 or

AAC. If you are concerned about the gap, please use

WAV or FLAC files.

Gapless playback is not possible when the format is

being converted (transcoded) by the server.

Gapless playback is not possible in the DMR mode.

Playback with NETWORK features

Music files

a. MPEG Layer-3 audio decoding technology licensed from

Fraunhofer IIS and Thomson multimedia.

b. Files encoded using Windows Media Codec 9 may be playable

but some parts of the specification are not supported;

specifically, Pro, Lossless, Voice.

c. Uncompressed FLAC files are not supported. Pioneer does not

guarantee playback.

Extension Stream

MP3 (MPEG-1 Audio Layer 3)

.mp3aSampling frequency 32 kHz, 44.1 kHz, 48 kHz

Quantization bitrate 16 bit

Channel 2 ch

Bitrate 8 kbps to 320 kbps

VBR/CBR Supported/Supported

WAV (LPCM)

.wav Sampling frequency 32 kHz, 44.1 kHz, 48 kHz,

88.2 kHz, 96 kHz,

176.4 kHz, 192 kHz

Quantization bitrate 16 bit, 24 bit

Channel 2 ch

WMA (WMA2/7/8/9)

.wmabSampling frequency 32 kHz, 44.1 kHz, 48 kHz

Quantization bitrate 16 bit

Channel 2 ch

Bitrate 5 kbps to 320 kbps

VBR/CBR Supported/Supported

AAC (MPEG-4 AAC LC, MPEG-4 HE AAC)

.m4a

.aac

.3gp

.3g2

Sampling frequency 32 kHz, 44.1 kHz, 48 kHz

Quantization bitrate 16 bit

Channel 2 ch

Bitrate 16 kbps to 320 kbps

VBR/CBR Supported/Supported

FLAC

.flaccSampling frequency 32 kHz, 44.1 kHz, 48 kHz,

88.2 kHz, 96 kHz,

176.4 kHz, 192 kHz

Quantization bitrate 16 bit, 24 bit

Channel 2 ch

AIFF

.aif

.aiff

Sampling frequency 32 kHz, 44.1 kHz, 48 kHz,

88.2 kHz, 96 kHz, 176.4 kHz,

192 kHz

Quantization bitrate 16 bit, 24 bit

Channel 2 ch

Apple Lossless

.m4a

.mp4

Sampling frequency 32 kHz, 44.1 kHz, 48 kHz,

88.2 kHz, 96 kHz

Quantization bitrate 16 bit, 24 bit

Channel 2 ch

Chapter

Home Menu

Using the Home Menu

The following section shows you how to make detailed

settings to specify how you’re using the receiver, and also

explains how to fine-tune individual speaker system settings

to your liking.

Important

•

The OSD will not appear if you have connected using the

composite output to your TV. Use HDMI connection for

Home Menu.

•

If headphones are connected to the receiver, disconnect

them.

•

You can’t use the Home Menu when the NETRADIO,

PANDORA, M.SERVER, FAVORITE, iPod/USB or

ADAPTER input is selected.

Switch on the receiver and your TV.

Press



STANDBY/ON

to switch on.

Switch the TV input to the input that connects this

receiver to the TV through the corresponding HDMI

cable.

Press

RECEIVER

, then press

HOME MENU

The Home Menu appears on your TV. Use

///-

and

ENTER

on the remote control to navigate through the

screens and select menu items. Press

RETURN

to exit

the current menu.

•

Press

HOME MENU

at any time to exit the Home

Menu.

Select the setting you want to adjust.

•

Auto MCACC – This is a quick and effective automatic

surround setup (see Automatically setting up for surround

sound (MCACC) on page 27).

•

Manual SP Setup

Speaker Setting – Specify the size and number of

speakers you’ve connected (see below).

X.Over – Specify which frequencies will be sent to the

subwoofer (page 54).

Channel Level – Adjust the overall balance of your

speaker system (page 54).

Speaker Distance – Specify the distance of your

speakers from the listening position (page 55).

•

Input Assign

Analog Input – Specify what you’ve connected to the

ANALOG IN1 audio input (page 55).

Component Input – Specify what you’ve connected to

the component video inputs (page 55).

•

Auto Power Down – Sets to automatically turn off the

power when the receiver has not operated for several hours

(see The Auto Power Down menu on page 56).

•

HDMI Setup – Set the audio return channel function or set

the HDMI input signal to Standby Through output or not

during standby (see HDMI Setup on page 59).

•

Network Standby – Allows the AirPlay function to be used

even when the receiver is in the standby mode (see The

Network Standby menu on page 56).

•

MHL Setup – Changes the settings related to MHL

(page 56).

•

Speaker System – Specifies how you are using the speaker

terminals (page 57).

•

OSD Setup – Sets the overlay function ON/OFF.

Manual speaker setup

This receiver allows you to make detailed settings to optimize

the surround sound performance. You only need to make

these settings once (unless you change the placement of your

current speaker system or add new speakers).

These settings are designed to fine-tune your system, but if

you’re satisfied with the settings made in Automatically

setting up for surround sound (MCACC) on page 27, it isn’t

necessary to make all of these settings.

Important

•

Depending on the Speaker System setting, there will be

differences in the speaker items that can be adjusted. The

OSD display for these operating instructions is an example

of when the Speaker System setting is set to Surr. Back.

Speaker Setting

Use this setting to specify your speaker configuration (size,

number of speakers). It is a good idea to make sure that the

settings made in Automatically setting up for surround sound

(MCACC) on page 27 are correct.

Select ‘Manual SP Setup’ from the Home Menu.

Select ‘Speaker Setting’ from the Manual SP Setup

menu.

Choose the set of speakers that you want to set then

select a speaker size.

Use

/-

to select the size (and number) of each of the

following speakers:

•

Front – Select LARGE if your front speakers reproduce bass

frequencies effectively, or if you didn’t connect a

subwoofer. Select SMALL to send the bass frequencies to

the subwoofer.

SLEEP

INPUTCTRL

BD GAME HDMI

S.SEL ECO

STANDBY/ON

RECEIVER SIGNAL SEL

SOURCE

STANDBY/ON

RECEIVER

CTRL

ENTER

RETURN

AUDIO P.

TOP

HOME

TOOLS

BAND PTY

ENTER

RETURNHOME

Home Menu

. Auto MCACC

. Manual SP Setup

. Input Assign

4. Auto Power Down

5. HDMI Setup

6. Network Standby

7. MHL Setup

8. Speaker System

9. 12V Trigger

10. OSD Setup

. Manual SP Setup

Return

. Speaker Setting

. X.Over

. Channel Level

. Speaker Distance

. Speaker Setting

Front

Center

Surr

Surr. Back

Subwoofer:

Return

[ SMALL ]

[ NO

]

YES

SMALL

Home Menu

•

Center – Select LARGE if your center speaker reproduces

bass frequencies effectively, or select SMALL to send bass

frequencies to the other speakers or subwoofer. If you

didn’t connect a center speaker, choose NO (the center

channel is sent to the other speakers).

•

Front Height – Select LARGE if your front height speakers

reproduce bass frequencies effectively. Select SMALL to

send bass frequencies to the other speakers or subwoofer.

If you didn’t connect front height speakers choose NO.

You can only adjust the Front Height setting when Pre

Out Setting is set to Height.

•

Surr – Select LARGE if your surround speakers reproduce

bass frequencies effectively. Select SMALL to send bass

frequencies to the other speakers or subwoofer. If you

didn’t connect surround speakers choose NO (the sound of

the surround channels is sent to the other speakers).

•

Surr. Back – Select the number of surround back speakers

you have (one, two or none). Select LARGE if your surround

back speakers reproduce bass frequencies effectively.

Select SMALL to send bass frequencies to the other

speakers or subwoofer. If you didn’t connect surround back

speakers choose NO.

When using only one surround back speaker, connect it

to the SURROUND BACK L (Single) terminals.

•

Subwoofer – LFE signals and bass frequencies of

channels set to SMALL are output from the subwoofer

when YES is selected (see notes below). Choose the PLUS

setting if you want the subwoofer to output bass sound

continuously or you want deeper bass (the bass

frequencies that would normally come out the front and

center speakers are also routed to the subwoofer). If you did

not connect a subwoofer choose NO (the bass frequencies

are output from other speakers).

When you’re finished, press

RETURN

You return to the Manual SP Setup menu.

Note

•

If you select SMALL for the front speakers, the subwoofer

will automatically be fixed to YES. Also, the center,

surround, surround back and front height speakers can’t

be set to LARGE if the front speakers are set to SMALL. In

this case, all bass frequencies are sent to the subwoofer.

•

If the surround speakers are set to NO, the surround back

speakers will automatically be set to NO.

•

If you have a subwoofer and like lots of bass, it may seem

logical to select LARGE for your front speakers and PLUS

for the subwoofer. This may not, however, yield the best

bass results. Depending on the speaker placement of your

room you may actually experience a decrease in the

amount of bass due to low frequency cancellations. In this

case, try changing the position or direction of speakers. If

you can’t get good results, listen to the bass response with

it set to PLUS and YES or the front speakers set to LARGE

and SMALL alternatively and let your ears judge which

sounds best. If you’re having problems, the easiest option

is to route all the bass sounds to the subwoofer by selecting

SMALL for the front speakers.

X.Over

•

Default setting: 100Hz

This setting decides the cutoff between bass sounds playing

back from the speakers selected as LARGE, or the subwoofer,

and bass sounds playing back from those selected as SMALL.

It also decides where the cutoff will be for bass sounds in the

LFE channel.

•

For more on selecting the speaker sizes, see Speaker Setting

on page 53.

Select ‘Manual SP Setup’ from the Home Menu.

Select ‘X.Over’ from the Manual SP Setup menu.

Choose the frequency cutoff point.

Frequencies below the cutoff point will be sent to the

subwoofer (or LARGE speakers).

When you’re finished, press

RETURN

You return to the Manual SP Setup menu.

Channel Level

Using the channel level settings, you can adjust the overall

balance of your speaker system, an important factor when

setting up a home theater system.

CAUTION

•

The test tones used in the Channel Level settings are output

at high volume.

Select ‘Manual SP Setup’ from the Home Menu.

Select ‘Channel Level’ from the Manual SP Setup menu.

Select a setup option.

•

Manual – Move the test tone manually from speaker to

speaker and adjust individual channel levels.

•

Auto – Adjust channel levels as the test tone moves

from speaker to speaker automatically.

Confirm your selected setup option.

The test tones will start after you press

ENTER

. After the

volume increases to the reference level, test tones will be

output.

. Manual SP Setup

Return

. Speaker Setting

. X.Over

. Channel Level

. Speaker Distance

. X.Over

Return

Frequency 100Hz

. Manual SP Setup

Return

. Speaker Setting

. X.Over

. Channel Level

. Speaker Distance

. Channel Level

ENTER:Next Return

Test Tone Manual

. Channel Level

Please Wait . . .20

Caution

Loud test tones

will be output.

Return

Test Tone [ Manual ]

Home Menu

Adjust the level of each channel using

/-

If you selected Manual, use

/

to switch speakers. The

Auto setup will output test tones in the order shown on-

screen:

Adjust the level of each speaker as the test tone is

emitted.

Note

•

If you are using a Sound Pressure Level (SPL) meter, take

the readings from your main listening position and adjust

the level of each speaker to 75 dB SPL (C-weighting/slow

reading).

•

The subwoofer test tone is output at low volumes. You may

need to adjust the level after testing with an actual

soundtrack.

When you’re finished, press

RETURN

You return to the Manual SP Setup menu.

Tip

•

You can change the channel levels at any time by press

SEL

and

CH LEVEL +/–

on the remote control. You can also

press

RECEIVER

, then press

CH SEL

and use

/

to select

the channel, and then use

/-

to adjust the channel

levels.

Speaker Distance

For good sound depth and separation from your system, you

need to specify the distance of your speakers from the

listening position. The receiver can then add the proper delay

needed for effective surround sound.

Select ‘Manual SP Setup’ from the Home Menu.

Select ‘Speaker Distance’ from the Manual SP Setup

menu.

Adjust the distance of each speaker using

/-

You can adjust the distance of each speaker in 0.1 feet

increments.

When you’re finished, press

RETURN

You return to the Manual SP Setup menu.

The Input Assign menu

Assigns input function for analog audio input terminal and

component video input terminal and component video input

terminal.

•

For the assignment of the digital signal inputs, see

Selecting the audio input signal on page 29.

Analog Input

ANALOG IN1 audio input terminal is assigned to CD under

factory settings, but this can be changed to TV input.

Select ‘Input Assign’ from the Home Menu.

Select ‘Analog Input’ from the Input Assign menu.

Select the desired input option for the ANALOG IN1

audio input terminal.

When you’re finished, press

RETURN

You return to the Input Assign menu.

Note

•

When playing analog input audio, switch to the CD or TV

input menu, press

RECEIVER

and press

SIGNAL SEL

several times to choose A (Analog). (see Selecting the audio

input signal on page 29)

Component Input

COMPONENT VIDEO IN1 input terminal is assigned to DVD

under factory settings, but this can be changed to SAT/CBL

input.

Select ‘Input Assign’ from the Home Menu.

. Channel Level

Front L

Center

Front R

Surround R

Surr. Back R

Surr. Back L

Surround L

Subwoofer

Return

[ 0dB ]

[

–

– ]

[

–

– ]

[ 0dB ]

0dB

. Manual SP Setup

Return

. Speaker Setting

. X.Over

. Channel Level

. Speaker Distance

Front L

Center

Front R

Surround R

Surr. Back R

Surr. Back L

Surround L

Subwoofer

Return

[ 10.0 ft ]

[ –

–

– ]

[ –

–

– ]

[ 10.0 ft ]

10.0 ft

. Input Assign

Return

. Analog Input

. Component Input

. Analog Input

Return

Analog CD

Home Menu

Select ‘Component Input’ from the Input Assign menu.

Select the desired input option for the COMPONENT

VIDEO IN1 input terminal.

Select between DVD, SAT/CBL or OFF.

When you’re finished, press

RETURN

You return to the Input Assign menu.

•

Make sure you have connected the audio from the

component to the corresponding inputs on the rear of

the receiver.

The Auto Power Down menu

Set to automatically turn off the receiver after a specified time

has passed (when the power has been on with no operation

and no audio signal).

•

Default setting: OFF

Select ‘Auto Power Down’ from the Home Menu.

Specify the amount of time to allow before the power

is turned off (when there has been no operation).

•

Select 15 minutes or 30 minutes, 60 minutes or OFF.

Important

•

Auto power down will occur if the HDMI AUDIO

PARAMETER is set to THRU and there is no operation.

•

Even if images are being output, if the input volume level is

exceptionally low, it will automatically turn OFF.

•

Depending on the connected device, the static caused by

the device may prevent the auto power down function from

activating.

•

If the input volume level is exceptionally low, in some cases

the auto power down function may be activated.

•

During photo viewer playback, continuing playback without

performing any control operations will activate auto power

down.

When you’re finished, press

RETURN

You return to the Home Menu.

The Network Standby menu

This setting allows the AirPlay function for operating the

receiver from a computer connected on the same LAN as the

receiver to be used even when the receiver is in the standby

mode.

Select ‘Network Standby’ from the Home Menu.

Choose ON or OFF for the Network Standby.

•

ON – The AirPlay function can be used even when the

receiver is in the standby mode.

•

OFF – The AirPlay function cannot be used when the

receiver is in the standby mode (This lets you reduce

power consumption in the standby mode).

If the Network Standby setting is set to ON, the

power consumption during standby will increase.

When you’re finished, press

RETURN

You return to the Home Menu.

The MHL Setup menu

Auto Switching

Select whether or not to switch the input automatically to the

MHL input when an MHL-compatible device is connected.

Note

•

This is only valid for MHL-compatible devices supporting

this function.

Select ‘MHL Setup’ from the Home Menu.

Select ‘Auto Switching’ from the MHL Setup menu.

Choose ON or OFF for the MHL Setup.

When you’re finished, press

RETURN

You return to the Home Menu.

Setup ROKU standby mode

Select ‘MHL Setup’ from the Home Menu.

Select ‘ROKU Standby’ from the MHL Setup menu.

Use

/-

to select the setting

•

OFF - When the receiver is in the standby mode, power is

not provided to the Roku Streaming Stick. Energy

consumption will decrease but it will take approximately 90

seconds for the images to be played back.

•

ON - Will provide power to the Roku Streaming Stick even

if the receiver is in the standby mode. Energy consumption

will increase but will be able to immediately playback

images.

Note

•

Power will be supplied even if a MHL device is connected.

. Input Assign

Return

. Analog Input

. Component Input

Return

Component DVD

Home Menu

. Auto MCACC

. Manual SP Setup

. Input Assign

4. Auto Power Down

5. HDMI Setup

6. Network Standby

7. MHL Setup

8. Speaker System

9. 12V Trigger

10. OSD Setup

. Auto Power Down

Return

Auto Power Down

OFF

. Network Standby

Return

Network Standby

OFF

Home Menu

. Auto MCACC

. Manual SP Setup

. Input Assign

4. Auto Power Down

5. HDMI Setup

6. Network Standby

7. MHL Setup

8. Speaker System

9. 12V Trigger

10. OSD Setup

. MHL Setup

Return

Auto Switching

ROKU Standby

[ OFF ]

Home Menu

. Auto MCACC

. Manual SP Setup

. Input Assign

4. Auto Power Down

5. HDMI Setup

6. Network Standby

7. MHL Setup

8. Speaker System

9. 12V Trigger

10. OSD Setup

Home Menu

When you’re finished, press

RETURN

You return to the Home Menu.

The Speaker System setting

Specify either using the surround back speaker (or the

speaker B), or the front height speaker connection with the B-

speaker terminals.

•

Default setting: Surr. Back

Select ‘Speaker System’ from the Home Menu.

Select the speaker system setting using

/-

•

Surr. Back – Sound is output from the surround back

speaker.

•

Height – Sound is output from front height speaker.

•

SP-B – Enables Speaker B to be installed in another

room so that the sound of the stereo can be enjoyed

elsewhere.

•

Bi-Amp – Enables higher quality playback sound

through the front speakers with the connection of bi-

amp speakers.

•

ZONE 2 – In a separate room (subzone) from which the

receiver is located (main zone), one can enjoy playback

of a device connected to the receiver (multi-zone

function).

When you’re finished, press

RETURN

You return to the Home Menu.

The 12 V Trigger Setting

If the input switches over to the input function set here, a

control signal is output from the receiver’s 12 V trigger

terminal, and operations such as power coupling with other

devices and equipment can be achieved.

Select ‘12V Trigger’ from the Home Menu.

Select the input function that triggers simultaneous

operation of 12 V trigger output.

Choose ON or OFF for the 12V Trigger.

When you’re finished, press

RETURN

You return to the Home Menu.

The OSD Setup menu

Sets the overlay function ON/OFF.

Select ‘OSD Setup’ from the Home Menu.

Choose ON or OFF for the OSD Setup.

When you’re finished, press

RETURN

You return to the Home Menu.

Home Menu

. Auto MCACC

. Manual SP Setup

. Input Assign

4. Auto Power Down

5. HDMI Setup

6. Network Standby

7. MHL Setup

8. Speaker System

9. 12V Trigger

10. OSD Setup

. Speaker System

Return

SP System Surr. Back

Home Menu

. Auto MCACC

. Manual SP Setup

. Input Assign

4. Auto Power Down

5. HDMI Setup

6. Network Standby

7. MHL Setup

8. Speaker System

9. 12V Trigger

10. OSD Setup

. OSD Setup

Return

OSD

Home Menu

. Auto MCACC

. Manual SP Setup

. Input Assign

4. Auto Power Down

5. HDMI Setup

6. Network Standby

7. MHL Setup

8. Speaker System

9. 12V Trigger

10. OSD Setup

Chapter

Using the MULTI-ZONE feature

MULTI-ZONE listening

This receiver can power up to two independent systems in

separate rooms after you have made the proper MULTI-ZONE

connections.

Different sources can be playing in two zones at the same

time or, depending on your needs, the same source can also

be used. The main and sub zones have independent power

(the main zone power can be off while the sub zone is on) and

the sub zone can be controlled by the remote or front panel

controls.

Making MULTI-ZONE connections

It is possible to make these connections if you have a separate

speakers for your sub zone.

Note

•

You can listen to the built-in tuner and other analog audio

sources in the sub zone.

•

You can’t use sound controls (such as the bass/treble

controls or Midnight listening) or any surround modes with

a separate amplifier in the sub zone. You can, however, use

the features available with your sub zone amplifier.

•

Use this after selecting ZONE 2 for The Speaker System

setting on page 57 on the Home Menu.



Connect a speaker to the SURROUND BACK/ZONE2

terminal on the rear of this receiver.

For details, see connection diagram on page 14.

You should have a pair of speakers attached to the sub

zone amplifier as shown.

Using the MULTI-ZONE controls

The following steps use the front panel controls to select

sources. See MULTI-ZONE remote controls below.

Press

CONTROL MULTI-ZONE ON/OFF

button on the

front panel.

The ZONE indicator lights when the MULTI-ZONE control

has been switched ON.

•

When the receiver is on, make sure that any operations

for the sub zone are done while ZONE lights in the

display. If this is not showing, the front panel controls

affect the main zone only. If the receiver is in standby,

the display is dimmed, and ZONE continues to light in

the display.

Press

CONTROL MULTI-ZONE ON/OFF

button on the

front panel.

Each press will switch between main zone and sub zone

control.

•

If no operation is performed for a few seconds, MULTI-

ZONE CONTROL mode will automatically end.

Press

INPUT SELECTOR

dial to select the source for the

zone you have selected.

For example, Z2: DVD sends the source connected to the

DVD inputs to the sub room (ZONE 2).

•

If you select TUNER, you can use the tuner controls to

select a preset station (see Saving station presets on

page 36 if you’re unsure how to do this). The tuner

cannot be tuned to more than one station at a time.

Therefore, changing the station in one zone also

changes the station in the other zone. Please be

careful not to change stations when recording a radio

broadcast.

Use

MASTER VOLUME

dial to adjust the volume for the

sub zone.

When you’re finished, press

CONTROL MULTI-ZONE

ON/OFF

again to return to the main zone controls.

You can also press

CONTROL MULTI-ZONE ON/OFF

button on the front panel to switch off all output to the

sub zone.

Note

•

You won’t be able to switch the main zone off completely

unless you’ve switched off the MULTI-ZONE control first.

•

If you don’t plan to use the MULTI-ZONE feature for a while,

turn off the power in both the sub and main rooms so that

this receiver is in standby.

MULTI-ZONE remote controls

With button pressed, press the buttons below to

operate the corresponding zone.

The following table shows the possible MULTI-ZONE remote

controls:

SPEAKERS BAND

CONTROL

MULTI-ZONE

ON/OFF

Button What it does



STANDBY/

Switches on/off power in the sub zone.

Input function

buttons

Use to select the input source directly in the

sub zone.

VOLUME +/–

Use to set the listening volume in the sub zone.

MUTE

Mutes the sound or restores the sound if it has

been muted (adjusting the volume also

restores the sound).

SHIFT

Chapter

Control with HDMI function

Synchronized operations below with a Control with HDMI-

compatible Pioneer TV or Blu-ray Disc player are possible

when the component is connected to the receiver using an

HDMI cable.

•

Synchronized amp mode

The receiver’s volume can be set and the sound can be

muted using the TV’s remote control.

•

Power synchronization with TV

•

Automatic switching of inputs

The receiver’s input switches over automatically when the

TV’s input is changed or a Control with HDMI-compatible

component is played.

Important

•

With Pioneer devices, the Control with HDMI functions are

referred to as “KURO LINK”.

•

You cannot use this function with components that do not

support Control with HDMI.

•

We only guarantee this receiver will work with Pioneer

made Control with HDMI-compatible components.

However, we do not guarantee that all synchronized

operations will work with components that support the

Control with HDMI function.

•

Use a High Speed HDMI®/™ Cable when you want to use

the Control with HDMI function. The Control with HDMI

function may not work properly if a different type of HDMI

cable is used.

•

For details about concrete operations, settings, etc., refer to

also the operating instructions for each component.

Making Control with HDMI connections

You can use synchronized operation for a connected TV and

other components.

•

Be sure to connect the TV’s audio cable to the audio input

of this unit. When the TV and receiver are connected by

HDMI connections, if the TV supports the HDMI Audio

Return Channel function, the sound of the TV is input to the

receiver via the HDMI terminal, so there is no need to

connect an audio cable. In this case, set ARC at HDMI

Setup to ON (see HDMI Setup below).

For details, see Connecting using HDMI on page 20.

Important

•

When connecting this system or changing connections, be

sure to switch the power off and disconnect the power cord

from the wall socket.

After completing all connections, connect the power cords

to the wall socket.

•

After this receiver is connected to an AC outlet, a 2 second

to 10 second HDMI initialization process begins. You

cannot carry out any operations during initialization. The

HDMI indicator on the display unit blinks during

initialization, and you can turn this receiver on once it has

stopped blinking.

•

To get the most out of this function, we recommend that

you connect your HDMI component not to a TV but rather

directly to the HDMI terminal on this receiver.

HDMI Setup

You must adjust the settings of this receiver as well as the

connected Control with HDMI-compatible components in

order to make use of the Control with HDMI function. For

more information see the operating instructions for each

component.

Switch on the receiver and your TV.

Press



STANDBY/ON

to switch on.

Switch the TV input to the input that connects this

receiver to the TV through the corresponding HDMI

cable.

Press

RECEIVER

, then press

HOME MENU

The Home Menu appears on your TV. Use

///-

and

ENTER

on the remote control to navigate through the

screens and select menu items. Press

RETURN

to exit

the current menu.

•

Press

HOME MENU

at any time to exit the Home

Menu.

Select ‘HDMI Setup’ from the Home Menu.

Select the ‘Control’ setting you want.

Choose whether to set this unit’s Control with HDMI

function ON or OFF. You will need to set it to ON to use

the Control with HDMI function.

When using a component that does not support the

Control with HDMI function, set this to OFF.

•

ON – Enables the Control with HDMI function. When

this unit’s power is turned off and you have a

supported source begin playback while using the

Control with HDMI function, the audio and video

outputs from the HDMI connection are output from the

TV.

•

OFF – The Control with HDMI is disabled.

Synchronized operations cannot be used. When this

unit’s power is turned off, audio and video of sources

connected via HDMI are not output.

If the Control setting is not set to OFF, the power

consumption during standby will increase.

Select the ‘ARC’ setting you want.

When a TV supporting the HDMI Audio Return Channel

function is connected to the receiver, the sound of the TV

can be input via the HDMI terminal.

•

ON – The TV’s sound is input via the HDMI terminal.

This can only be selected when Control is set to ON.

•

OFF – The TV’s sound is input from the audio input

terminals other than HDMI inputs.

Choose the ‘Standby Through’ setting you want.

When the receiver is in standby, the HDMI input signal

selected here will be output to the TV by HDMI.

•

LAST – The HDMI input signal selected previously will

be output.

Home Menu

. Auto MCACC

. Manual SP Setup

. Input Assign

4. Auto Power Down

5. HDMI Setup

6. Network Standby

7. MHL Setup

8. Speaker System

9. 12V Trigger

10. OSD Setup

. HDMI Setup

Return

Control

OFF

ARC

[

OFF

]

Standby Through

[

OFF

]

Control with HDMI function

•

BD, DVD, SAT/CBL, MHL, HDMI, GAME – The HDMI

input signal selected here will be output.

•

OFF – Signal will not be output during standby.

(However, when Control is set to ON, the HDMI signal

is transferred through by the Control with HDMI

function even when in the standby mode.)

If the Standby Through setting is not set to OFF, the

power consumption during standby will increase.

This setting can be used even with devices that are

not compatible with the Control with HDMI

function.

The Standby Through function cannot be used with

MHL-compatible devices.

When you’re finished, press

RETURN

You return to the Home Menu.

Before using synchronization

Once you have finished all connections and settings, you

must:

Put all components into standby mode.

Turn the power on for all components, with the power

for the TV being turned on last.

Choose the HDMI input to which the TV is connected to

this receiver, and see if video output from connected

components displays properly on the screen or not.

Check whether the components connected to all HDMI

inputs are properly displayed.

About synchronized operations

The Control with HDMI-compatible component connected to

the receiver operates in sync as described below.

•

Synchronized amp mode

From the menu screen of the Control with HDMI-

compatible TV, set audio to be played through this

receiver, and the receiver will switch to the synchronized

amp mode.

When in the synchronized amp mode, the synchronized

amp mode is canceled when the receiver’s power is

turned off. To turn the synchronized amp mode back on,

set audio to be played through the receiver from the TV’s

menu screen, etc. This receiver will power up and switch

to the synchronized amp mode.

When in the synchronized amp mode, the synchronized

amp mode is canceled if an operation that produces

sound from the TV is performed from the TV’s menu

screen, etc.

When the synchronized amp mode is canceled, the

receiver’s power turns off if you were viewing an HDMI

input or a TV program on the TV.

•

Power synchronization with TV

When the TV’s power is set to standby, the receiver’s

power is also set to standby. (Only when the input for a

component connected to the receiver by HDMI

connection is selected or when watching the TV.)

•

Automatic switching of inputs

The receiver’s input switches automatically when the

Control with HDMI-compatible component is played.

The receiver’s input switches automatically when the

TV’s input is switched.

The synchronized amp mode remains in effect even if the

receiver’s input is switched to a component other than

one connected by HDMI.

Cautions on the Control with HDMI function

•

Connect the TV and components (Blu-ray Disc player, etc.)

directly to this receiver. Interrupting a direct connection

with other amps or an AV converter (such as an HDMI

switch) can cause operational errors.

•

When the receiver’s Control is turned ON, even if the

receiver’s power is in the standby mode, it is possible to

output the audio and video signals from a player via HDMI

to the TV without producing sound from the receiver, but

only when a Control with HDMI-compatible component

(Blu-ray Disc player, etc.) and compatible TV are

connected. In this case, the receiver’s power turns on and

the power and HDMI indicators light.

Chapter

Additional information

Troubleshooting

Incorrect operations are often mistaken for trouble and

malfunctions. If you think that there is something wrong with

this component, check the points below. Take a look at the

other components and electrical appliances being used,

because sometimes the problem may lie there. If the trouble

isn’t sorted out even after going through the checks below,

ask your nearest Pioneer authorized independent service

company to carry out repair work.

•

If the unit does not operate normally due to external effects

such as static electricity disconnect the power plug from

the outlet and insert again to return to normal operating

conditions.

General

The power does not turn on.

Disconnect the power plug from the outlet, and insert again.

Make sure there are no loose strands of speaker wire touching

the rear panel. This could cause the receiver to shut off

automatically.

The receiver suddenly switches off.

When the Auto Power Down function is working, the power will

automatically turn off if the receiver has not operated for

several hours. Check the setting for the Auto Power Down

function (see The Auto Power Down menu on page 56).

After about a minute (you won’t be able to switch the unit on

during this time), switch the receiver back on. If the message

persists, call a Pioneer authorized independent service

company.

If there is very little low frequency information in the source

material, change your speaker settings to Front: SMALL /

Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS (page 53).

The HDMI indicator blinks and the power does not turn

on.

The receiver may have a serious problem. Do not try switching

the receiver on. Unplug the receiver from the wall and call a

Pioneer authorized independent service company.

The power suddenly turns on or off, or the input suddenly

changes (When the Control with HDMI is ON).

This happens because of the synchronized operation due to

the Control with HDMI function. If synchronized operations

are not needed, set the Control with HDMI to OFF (see HDMI

Setup on page 59).

OVERHEAT shows in the display and the power turns off.

The temperature within the unit has exceeded the allowable

value. Try moving the unit for better ventilation (page 2).

Lower the volume level.

TEMP shows in the display and the volume level drops.

The temperature within the unit has exceeded the allowable

value. Try moving the unit for better ventilation (page 2).

Lower the volume level.

No sound is output when an input function is selected.

Use

VOLUME +/–

to turn up the volume.

Press

MUTE

on the remote control to turn muting off.

Press

SP-A/B

to select the proper speaker set (see Switching

the speaker terminal on page 18).

Set the

SIGNAL SEL

to H (HDMI), C1/O1 (digital) or A (analog)

according to the type of connections made (page 29).

Make sure the component is connected correctly (refer to

Connecting your equipment on page 14).

Check the audio output settings of the source component.

Refer to the instruction manual supplied with the source

component.

No image is output when an input function is selected.

Make sure the component is connected correctly (refer to

Connecting your equipment on page 14).

Use the same type of video cables for the source component

and TV to connect to this receiver (see About video outputs

connection on page 19).

Check The Input Assign menu on page 55 to make sure you’re

assigned the correct input.

The video input selected on the TV monitor is incorrect. Refer

to the instruction manual supplied with the TV.

No sound from subwoofer.

Make sure the subwoofer is switched on.

If the subwoofer has a volume knob, make sure it’s turned up.

The Dolby Digital or DTS source you are listening to may not

have an LFE channel.

Switch the subwoofer setting in Speaker Setting on page 53 to

YES or PLUS.

Switch the LFE ATT (LFE Attenuate) on page 40 to LFEATT 0 or

LFEATT 5.

No sound from surround or center speakers.

Connect the speakers properly (page 15).

Refer to Speaker Setting on page 53 to check the speaker

settings.

Refer to Channel Level on page 54 to check the speaker levels.

The OSD screen (Home Menu, etc.) isn’t displayed.

The OSD will not appear if you have connected using the

composite output to your TV. Use HDMI connection when

setting up the system.

The Phase Control feature doesn’t seem to have an

audible effect.

If applicable, check that the lowpass filter switch on your

subwoofer is off, or the lowpass cutoff is set to the highest

frequency setting. If there is a PHASE setting on your

subwoofer, set it to 0º (or depending on the subwoofer, the

setting where you think it has the best overall effect on the

sound).

Make sure the speaker distance setting is correct for all

speakers (see Speaker Distance on page 55).

Considerable noise in radio broadcasts.

Connect the antenna (page 23) and adjust the position for best

reception.

Route any loose cables away from the antenna terminals and

wires.

Fully extend the FM wire antenna, position for best reception,

and secure to a wall (or connect an outdoor FM antenna).

Connect an additional internal or external AM antenna

(page 23).

Turn off equipment causing interference or move it away from

the receiver (or move antennas farther away from equipment

causing noise).

Broadcast stations cannot be selected automatically.

Connect an outdoor antenna (page 23).

Noise during playback of a cassette deck.

Move the cassette deck away from your receiver, until the noise

disappears.

No sound is output or a noise is output when software

with DTS is played back.

Make sure the player’s settings are correct and/or the DTS

signal out is on. Refer to the instruction manual supplied with

the DVD player.

There seems to be a time lag between the speakers and

the output of the subwoofer.

See Automatically setting up for surround sound (MCACC) on

page 27 to set up your system again using MCACC (this will

automatically compensate for a delay in the subwoofer output).

After using the Auto MCACC setup, the speaker size

setting (LARGE or SMALL) is incorrect.

Low-frequency noise could have been caused by an air

conditioner or motor. Switch off all appliances in the room and

rerun the Auto MCACC setup.

Additional information

Can’t operate the remote control.

Replace the batteries (page 12).

Operate within 7 m (23 ft.), 30º of the remote sensor (page 13).

Remove the obstacle or operate from another position.

Avoid exposing the remote sensor on the front panel to direct

light.

Press the remote control’s

RECEIVER

button and switch to

receiver control mode.

The display is dark.

Press

DIMMER

on the remote control repeatedly to return to

the default.

During ECO mode, the brightness switches between 2 levels. If

the dimmest level is selected, DIMMER will be shown on the

display. (Mode other than ECO: 4 levels, ECO mode: 2 levels)

Display blinks 12V ERR.

An error has arisen in the 12 V trigger jack. Reconnect

accurately then turn the power back on.

The receiver doesn’t recognize iPod touch/iPhone.

Try the following.

1. Simultaneously keep pressing the sleep button and home

button on the iPod touch or iPhone for over 10 seconds to

restart.

2. Turn on the receiver.

3. Connect the iPod touch/iPhone to the receiver.

The Bluetooth wireless technology device cannot be

connected or operated. Sound from the Bluetooth

wireless technology device is not emitted or the sound is

interrupted.

Check that no object that emits electromagnetic waves in the

2.4 GHz band (microwave oven, wireless LAN device or

Bluetooth wireless technology apparatus) is near the unit. If

such an object is near the unit, set the unit far from it. Or, stop

using the object emitting the electromagnetic waves.

Check that the Bluetooth wireless technology device is not too

far from the unit and that obstructions are not set between the

Bluetooth wireless technology device and the unit. Set the

Bluetooth wireless technology device and the unit so that the

distance between them is less than about 10 m and no

obstructions exist between them.

Check that the Bluetooth ADAPTER and the ADAPTER PORT

terminal of the unit are correctly connected.

The Bluetooth wireless technology device may not be set to the

communication mode supporting the Bluetooth wireless

technology. Check the setting of the Bluetooth wireless

technology device.

Check that pairing is correct. The pairing setting was deleted

from this unit or the Bluetooth wireless technology device.

Reset the pairing.

Check that the profile is correct. Use a Bluetooth wireless

technology device that supports A2DP profile and AVRCP

profile.

Display flashes and cannot be operated.

Depending on the input signal or listening mode, there may be

functions that cannot be selected.

NETWORK feature

Cannot access the network.

The LAN cable is not firmly connected. Firmly connect the LAN

cable (page 22).

The router is not switched on. Switch on the router.

Internet security software is currently installed in the

connected component. There are cases where a component

with Internet security software installed cannot be accessed.

The audio component on the network which has been

switched off is switched on. Switch on the audio component

on the network before switching on this receiver.

Playback does not start while ‘Connecting Wired...’

continues to be displayed.

The component is currently disconnected from this receiver or

the power supply. Check whether the component is properly

connected to this receiver or the power supply.

The PC or Internet radio is not properly operated.

The corresponding IP address is not properly set. Switch on the

built-in DHCP server function of your router, or set up the

network manually according to your network environment

(page 56).

The IP address is being automatically configured. The

automatic configuration process takes time. Please wait.

The audio files stored on components on the network,

such as a PC, cannot be played back.

Windows Media Player 11 or Windows Media Player 12 is not

currently installed on your PC. Install Windows Media Player 11

or Windows Media Player 12 on your PC.

Audio files recorded in MPEG-4 AAC or FLAC are being played

back on Windows Media Player 11 or Windows Media Player

12. Audio files recorded in MPEG-4 AAC or FLAC cannot be

played back on Windows Media Player 11 or Windows Media

Player 12. Try using another server. Refer to the operation

manual supplied with your server.

The component connected to the network is not properly

operated.

Check whether the component is affected by special

circumstances or is in the sleep mode.

Try rebooting the component if necessary.

The component connected to the network does not permit file

sharing. Try changing the settings for the component

connected to the network.

The folder stored on the component connected to the network

has been deleted or damaged. Check the folder stored on the

component connected to the network.

Network connections could be restricted due to the

computer’s network settings, security settings, etc. Check the

computer’s network settings, security settings, etc.

The audio files are copyrighted. DRM-protected audio files

cannot be played back on this receiver.

Cannot access the component connected to the network.

The component connected to the network is not properly set. If

the client is automatically authorized, you need to enter the

corresponding information again. Check whether the

connection status is set to “Do not authorize”.

There are no playable audio files on the component connected

to the network. Check the audio files stored on the component

connected to the network.

Audio playback is undesirably stopped or disturbed.

The audio file currently being played back was not recorded in

a format playable on this receiver.

Check whether the audio file was recorded in a format

supported by this receiver.

Check whether the folder has been damaged or corrupted.

Note that there are cases where even the audio files listed as

playable on this receiver cannot be played back or displayed

(page 51).

The LAN cable is currently disconnected. Connect the LAN

cable properly (page 22).

There is heavy traffic on the network with the Internet being

accessed on the same network. Use 100BASE-TX to access the

components on the network.

When in the DMR mode, depending on the external controller

being used, playback may be interrupted when a volume

operation is performed from the controller. In this case, adjust

the volume from the receiver or remote control.

There is a connection routed through a wireless LAN on

the same network.

There may be a shortage of bandwidth on the 2.4 GHz band

used by the wireless LAN. Make wired LAN connections not

routed through a wireless LAN.

Install away from any devices emitting electromagnetic waves

on the 2.4 GHz band (microwave ovens, game consoles, etc.). If

Additional information

this does not solve the problem, stop using other devices that

emit electromagnetic waves.

Cannot access Windows Media Player 11 or Windows

Media Player 12.

In case of Windows Media Player 11: You are currently logged

onto the domain through your PC with Windows XP or

Windows Vista installed. Instead of logging onto the domain,

log onto the local machine (page 43).

In case of Windows Media Player 12: You are currently logged

onto the domain through your PC with Windows 7 or 8

installed. Instead of logging onto the domain, log onto the local

machine (page 43).

Cannot listen to Internet radio stations.

The firewall settings for components on the network are

currently in operation. Check the firewall settings for

components on the network.

You are currently disconnected from the Internet. Check the

connection settings for components on the network, and

consult with your network service provider if necessary

(page 46).

The broadcasts from an Internet radio station are stopped or

interrupted. There are cases where you cannot listen to some

Internet radio stations even when they are listed in the list of

Internet radio stations on this receiver (page 44).

The NETWORK function cannot be operated with the

buttons on the remote control.

The remote control is not currently set to the NETWORK mode.

Press

NET

to set the remote control to the NETWORK mode

(page 50).

This unit cannot be selected from the Spotify application.

An Internet connection is required for both the mobile device

and this unit.

Connect the mobile device by Wi-Fi to the wireless LAN router

of the same network as the one to which this unit is connected.

A Spotify Premium account (for a charge) must be registered

on the Spotify application.

When this unit is in standby, it cannot be selected from the

Spotify application.

The sound of the Spotify audio stream is not produced.

Check whether this unit is selected on the Spotify application.

Check that contents are playing on the Spotify application.

If the above does not solve the problem, turn this unit’s power

off then back on.

This unit’s volume does not increase when the volume

slider in the Spotify application is raised.

On some models, there is an upper limit to the volume to

prevent the volume from being too high accidentally. To raise

the volume higher in this case, do so by operating the remote

control. When using an application such as iControlAV, the

volume can also be increased from the application.

Playback continues on this unit when the Spotify

application is quit.

The Spotify audio stream continues from this unit, even when

the Spotify application is quit. To operate again, relaunch the

Spotify application.

Troubleshooting of wireless LAN

WLAN ERR shows in the display.

There might be an irregularity with the WLAN adaptor

connected to the DC OUTPUT for WIRELESS LAN on the rear

panel.

If WLAN ERR shows in the display when Network Standby is

ON, please pull out the AC power cord. When the AC power

cord is reconnected after 10 seconds, the WLAN ERR will be

canceled.

Network cannot be accessed via wireless LAN.

Wireless LAN converter’s power is not on (Wireless LAN

converter’s “Power”, “WPS” and “Wireless” indicators are not

all lit). Check that the USB cable connecting the wireless LAN

converter to the receiver’s DC OUTPUT for WIRELESS LAN

terminal is properly connected.

The LAN cable is not firmly connected. Firmly connect the LAN

cable (page 22).

Wireless LAN converter and base unit (wireless LAN router,

etc.) are too far apart or there is an obstacle between them.

Improve the wireless LAN environment by moving the wireless

LAN converter and base unit closer together, etc.

There is a microwave oven or other device generating

electromagnetic waves near the wireless LAN environment.

Use the system in a place away from microwave ovens or

others device generating electromagnetic waves.

Avoid using devices generating electromagnetic waves as

much as possible when using the system with the wireless

LAN.

Multiple wireless LAN converters are connected to the wireless

LAN router. When connecting multiple wireless LAN

converters, their IP addresses must be changed. For example,

if the wireless LAN router’s IP address is “192.168.1.1”, set the

first wireless LAN converter’s IP address to “192.168.1.249”,

the second wireless LAN converter’s IP address to

“192.168.1.248”, using values between 2 and 249 (such as “249”

and “248”) that are not assigned to other wireless LAN

converters or to other devices.

Wireless LAN connections cannot be established between the

wireless LAN converter and base unit (wireless LAN router,

etc.).

With the wireless LAN converter connected to the receiver,

turn the receiver’s power off, unplug the power cord from the

power outlet, then plug the power cord back in and turn the

receiver’s power on.

The wireless LAN converter must be set in order to establish

wireless LAN connections. For details, refer to the operating

instructions of the wireless LAN converter.

The wireless LAN converter is properly connected to the

receiver and the wireless LAN converter’s indicators are lit, but

the wireless LAN converter cannot be set from the receiver (the

settings screen cannot be displayed).

If Network Modes in the receiver’s Network Settings is set

to STATIC and the IP address has been set manually, the IP

address set in the wireless LAN converter may not match. In

the receivers Network Settings, set Network Modes to

DHCP. After the setting is completed, turn the receiver’s power

off. Next, turn the receiver’s power back on and check whether

the wireless LAN converter’s settings can be displayed with

the receiver.

If the settings can be displayed, change the IP address settings

of the receiver and wireless LAN converter as necessary.

The IP address settings of the receiver and wireless LAN

converter do not match the settings of the wireless LAN router,

etc.

Check the IP address settings of the receiver and wireless LAN

converter (including the Network Modes).

If the receiver’s Network Modes is DHCP, turn the receiver’s

power off, then turn the power back on.

Check that the IP addresses of the receiver and wireless LAN

converter match the settings of the wireless LAN router, etc. If

the receiver’s Network Modes is STATIC, set an IP address

matching the network of the base unit (wireless LAN router,

etc.).

For example, if the wireless LAN router’s IP address is

“192.168.1.1”, set the receiver’s IP address to “192.168.1.XXX”

(*1), the subnet mask to “255.255.255.0”, the gateway and DNS

to “192.168.1.1”.

Next, set the wireless LAN converter’s IP address to

“192.168.1.249” (*2).

Additional information

(*1) Set the “XXX” in “192.168.1.XXX” to a number between 2

and 248 that is not assigned to other devices.

(*2) Set the “249” in “192.168.1.249” to a number between 2

and 249 that is not assigned to other devices.

Try making the wireless LAN converter’s advanced settings.

The wireless LAN converter can be connected to a computer to

make the advanced wireless LAN settings. For details, see the

CD-ROM included for the wireless LAN converter. Check the

settings of the wireless LAN router, etc., then change the

settings of the wireless LAN converter.

Note, however, that making the advanced wireless LAN

settings will not necessarily improve the wireless LAN

environment. Be careful when changing the settings.

The access point is set to conceal the SSID. In this case, the

SSID may not be displayed on the access point list screen. If

not, set the SSID, etc., by making the wireless LAN converter

settings on the receiver manually.

The access point’s security settings use WEP 152-bit length

code key or shared key authentication. The receiver does not

support WEP 152-bit length code key or shared key

authentication.

Network connections cannot be established even when the

above measures are taken. Reset the wireless LAN converter.

After this, redo the wireless LAN converter’s settings.

About resetting

1. Check that the wireless LAN converter’s power is on.

2. Press the wireless LAN converter’s reset button for at least

3 seconds.

3. Release the reset button.

When the wireless LAN converter is restarted, the resetting

procedure is completed.

HDMI

No picture or sound.

If the problem still persists when connecting your HDMI

component directly to your monitor, please consult the

component or monitor manual or contact the manufacturer for

support.

No picture.

Video signals that are input from the analog video terminal will

not output from the HDMI terminal. Signals that are input from

the HDMI terminal will not output from the analog video

terminal. Be consistent with the type of cable between input

and output.

Depending in the output settings of the source component, it

may be outputting a video format that can’t be displayed.

Change the output settings of the source, or connect using the

composite video jacks.

This receiver is HDCP-compatible. Check that the components

you are connecting are also HDCP-compatible. If they are not,

please connect them using the composite video jacks.

Depending on the connected source component, it’s possible

that it will not work with this receiver (even if it is HDCP-

compatible). In this case, connect using the composite video

jacks between source and receiver.

If video images do not appear on your TV, try adjusting the

resolution, Deep Color or other setting for your component.

To output signals in Deep Color, use an HDMI cable (High

Speed HDMI®/™ Cable) to connect this receiver to a

component or TV with the Deep Color feature.

No sound, or sound suddenly ceases.

Check that the HDMI setting is set to AMP (page 39).

If the component is a DVI device, use a separate connection for

the audio.

HDMI format digital audio transmissions require a longer time

to be recognized. Due to this, interruption in the audio may

occur when switching between audio formats or beginning

playback.

Turning on/off the device connected to this unit’s HDMI OUT

terminal during playback, or disconnecting/connecting the

HDMI cable during playback, may cause noise or interrupted

audio.

Synchronized operation not possible using Control with

HDMI function.

Check the HDMI connections.

The cable may be damaged.

Select ON for the Control with HDMI setting (see HDMI Setup

on page 59).

Turn the TV’s power on before turning on this receiver’s power.

Set the TV side Control with HDMI setting to on (see TV’s

operating instructions).

Important information regarding the HDMI

connection

There are cases where you may not be able to route HDMI

signals through this receiver (this depends on the HDMI

equipped component you are connecting-check with the

manufacturer for HDMI compatibility information).

If you aren’t receiving HDMI signals properly through this

receiver (from your component), please try the following

configuration when connecting up.

Configuration

Connect your HDMI-equipped component directly to the

display using an HDMI cable. Then use the most convenient

connection (digital is recommended) for sending audio to the

receiver. See the operating instructions for more on audio

connections. Set the display volume to minimum when using

this configuration.

Note

•

Depending on the component, audio output may be limited

to the number of channels available from the connected

display unit (for example audio output is reduced to 2

channels for a monitor with stereo audio limitations).

•

If you want to switch the input source, you’ll have to switch

functions on both the receiver and your display unit.

•

Since the sound is muted on the display when using the

HDMI connection, you must adjust the volume on the

display every time you switch input sources.

Windows 8

This product is Windows 8.1 Compatible and Windows 8

Compatible.

Windows® and the Windows logo are trademarks of the

Microsoft group of companies.

MHL

Additional information

MHL, the MHL Logo, and Mobile High-Definition Link are

trademarks or registered trademarks of MHL, LLC in the United

States and other countries.

This receiver incorporates MHL 2.

HTC Connect

HTC, HTC Connect and the HTC Connect logo are trademarks

of HTC Corporation.

About iPod/iPhone

AirPlay works with iPhone, iPad, and iPod touch with iOS

4.3.3 or later, Mac with OS X Mountain Lion, and Mac and PC

with iTunes 10.2.2 or later.

USB works with iPhone 5s, iPhone 5c, iPhone 5, iPhone 4s,

iPhone 4, iPhone 3GS, iPhone 3G, iPhone, iPod touch (1st

through 5th generation) and iPod nano (3rd through 7th

generation).

“Made for iPod” and “Made for iPhone” mean that an

electronic accessory has been designed to connect

specifically to iPod or iPhone, respectively, and has been

certified by the developer to meet Apple performance

standards. Apple is not responsible for the operation of this

device or its compliance with safety and regulatory standards.

Please note that the use of this accessory with iPod or iPhone

may affect wireless performance.

Apple, AirPlay, iPad, iPhone, iPod, iPod nano, iPod touch,

iTunes, Safari, Bonjour and Mac are trademarks of Apple Inc.,

registered in the U.S. and other countries. The AirPlay logo is a

trademark of Apple Inc.

App Store is a service mark of Apple Inc.

Apple Lossless Audio Codec

Licensed under the Apache License, Version 2.0. You may

obtain a copy of the License at

http://www.apache.org/licenses/LICENSE-2.0.

About FLAC

FLAC Decoder

2008, 2009 Josh Coalson

Redistribution and use in source and binary forms, with or

without modification, are permitted provided that the

following conditions are met:

•

Redistributions of source code must retain the above

disclaimer.

•

Redistributions in binary form must reproduce the above

disclaimer in the documentation and/or other materials

provided with the distribution.

•

Neither the name of the Xiph.org Foundation nor the

names of its contributors may be used to endorse or

promote products derived from this software without

specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS

AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED

WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO

EVENT SHALL THE FOUNDATION OR CONTRIBUTORS BE

LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,

EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,

BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE

GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR

BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY

THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT

LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR

OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS

SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH

DAMAGE.

Additional information

About messages displayed when using

network functions

Refer to the following information when you come up with a

status message while operating the Network functions.

Resetting the main unit

Use this procedure to reset all the receiver’s settings to the

factory default. Use the front panel controls to do this.

•

For instructions on resetting the network connection

settings, see Factory Reset on page 49.

Switch the receiver into standby.

While holding down

BAND

, press and hold



STANDBY/ON

for about two seconds.

When you see RESET? appear in the display, press

AUTO SURROUND/STREAM DIRECT

OK? shows in the display.

Press

ALC/STANDARD SURR

to confirm.

OK appears in the display to indicate that the receiver

has been reset to the factory default settings.

Important

•

If the Control with HDMI function is set to ON, the HDMI

function’s Standby Through is set to anything other than

OFF, or the Network Standby is set to ON, you may not be

able to reset the unit. In this case, reset either by turning

OFF the Control with HDMI function, or by putting the unit

into standby mode by turning off the power of all the

connected devices, and resetting after the HDMI indicator

on the front panel turns off.

Cleaning the unit

•

Use a polishing cloth or dry cloth to wipe off dust and dirt.

•

When the surface is dirty, wipe with a soft cloth dipped in

some neutral cleanser diluted five or six times with water,

and wrung out well, and then wipe again with a dry cloth.

Do not use furniture wax or cleansers.

•

Never use thinners, benzine, insecticide sprays or other

chemicals on or near this unit, since these will corrode the

surface.

Status messages Descriptions

Connection Down The selected category or Internet radio

station cannot be accessed.

File Format Error Cannot be played back for some

reasons.

Track Not Found The selected song has not been found

anywhere on the network.

Server Error The selected server cannot be accessed.

Server Disconnected The server has been disconnected.

Empty There are no files stored in the selected

folder.

License Error The license for the contents to be played

back is invalid.

Item Already Exists This is displayed when the file you have

attempted to register in the Favorites

folder has already been registered.

Favorite List Full This is displayed when you have

attempted to register a file in the

Favorites folder but the Favorites folder is

already full.

Manufactured under license from Dolby Laboratories. Dolby,

Pro Logic, Surround EX, and the double-D symbol are

trademarks of Dolby Laboratories.

For DTS patents, see http://patents.dts.com. Manufactured

under license from DTS Licensing Limited. DTS, DTS-HD, the

Symbol, & DTS and the Symbol together are registered

trademarks, and DTS-HD Master Audio is a trademark of DTS,

Additional information

Specifications

Amplifier section

Continuous average power output of 80 watts* per

channel, min., at 8 ohms, from 20 Hz to 20 000 Hz with no

more than 0.08 %** total harmonic distortion.

Front (stereo) . . . . . . . . . . . . . . . . . . . . . . . . . . 80 W + 80 W

Guaranteed speaker impedance . . . . . . . . . . . . . . . 6  to 16 

* Measured pursuant to the Federal Trade Commission’s Trade

Regulation rule on Power Output Claims for Amplifiers

** Measured by Audio Spectrum Analyzer

Audio Section

Input (Sensitivity/Impedance)

LINE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200 mV/47 k

Signal-to-Noise Ratio (IHF, short circuited, A network)

LINE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98 dB

Signal-to-Noise Ratio [EIA, at 1 W (1 kHz)]

LINE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 dB

Video Section

Signal level

Composite. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Vp-p (75 )

Signal Level

Component Video

. . . . . . . . . . . . . . . Y: 1.0 Vp-p (75 ), PB/PR: 0.7 Vp-p (75 )

Corresponding maximum resolution

Component Video. . . . . . . . . . . . . . . . . . . . . . . . .1080p (1125p)

Tuner Section

Frequency Range (FM). . . . . . . . . . . . . . 87.5 MHz to 108 MHz

Antenna Input (FM) . . . . . . . . . . . . . . . . . . . . 75  unbalanced

Frequency Range (AM) . . . . . . . . . . . . . . 530 kHz to 1 700 kHz

Antenna (AM) . . . . . . . . . . . . . . . . . . . . . . . . . . . .Loop antenna

Digital In/Out Section

HDMI terminal . . . . . . . . . . . . . . . . . . . . . . . . . . Type A (19-pin)

HDMI output type. . . . . . . . . . . . . . . . . . . . . . . . . . 5 V, 100 mA

HDMI input/MHL terminal. . . . . . . . . . . . . . . . . . . 5 V, 900 mA

USB terminal . . . . . . . . USB2.0 High Speed (Type A) 5 V, 1 A

iPod terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .USB

ADAPTER PORT terminal . . . . . . . . . . . . . . . . . . . 5 V, 100 mA

Network Section

LAN terminal . . . . . . . . . . . . . . . . . . . 10 BASE-T/100 BASE-TX

Integrated control section

Control (IR) terminal . . . . . . . . . . . . . Ø 3.5 Mini-jack (MONO)

IR signal . . . . . . . . . . . . . . . . . . High Active (High Level: 2.0 V)

12 V Trigger terminal . . . . . . . . . . . . . Ø 3.5 Mini-jack (MONO)

12 V Trigger output type . . . . . . . . . . . . . . . . . . . . 12 V, 150 mA

Miscellaneous

Power Requirements. . . . . . . . . . . . . . . . . . . . AC 120 V, 60 Hz

Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . .520 W

In standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.1 W

Dimensions . . . . . 435 mm (W) x 168 mm (H) x 342.5 mm (D)

171/8 in. (W) x 65/8 in. (H) x 131/2 in. (D)

Weight (without package). . . . . . . . . . . . . . . 9.2 kg (20 lb 5 oz)

Furnished Parts

Microphone (for Auto MCACC setup) . . . . . . . . . . . . . . . . . . . 1

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Dry cell batteries (AAA size IEC R03). . . . . . . . . . . . . . . . . . . . 2

AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

FM wire antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Warranty card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Quick start guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safety Brochure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

SPEAKER CAUTION Sheet (English only). . . . . . . . . . . . . . . . 1

These operating instructions (CD-ROM)

Note

•

Specifications and the design are subject to possible

modifications without notice, due to improvements.

•

This product includes FontAvenue® fonts licensed by NEC

Corporation. FontAvenue is a registered trademark of NEC

Corporation.

•

Android and Google Play are trademarks of Google Inc.

The Safety of Your Ears is in Your Hands

Get the most out of your equipment by playing it at a

safe level – a level that lets the sound come through

clearly without annoying blaring or distortion and, most

importantly, without affecting your sensitive hearing.

Sound can be deceiving. Over time, your hearing

“comfort level” adapts to higher volumes of sound, so

what sounds “normal” can actually be loud and

harmful to your hearing. Guard against this by setting

your equipment at a safe level BEFORE your hearing

adapts.

ESTABLISH A SAFE LEVEL:

• Set your volume control at a low setting.

• Slowly increase the sound until you can hear it

comfortably and clearly, without distortion.

• Once you have established a comfortable sound

level, set the dial and leave it there.

BE SURE TO OBSERVE THE FOLLOWING

GUIDELINES:

• Do not turn up the volume so high that you can’t

hear what’s around you.

• Use caution or temporarily discontinue use in

potentially hazardous situations.

• Do not use headphones while operating a motorized

vehicle; the use of headphones may create a traffic

hazard and is illegal in many areas.

S001a_A1_En

<ARB7541-A>

To register your product, find the nearest authorized service location, to purchase replacement parts,

operating instructions, or accessories, please go to one of following URLs :

Pour enregistrer votre produit, trouver le service après-vente agréé le plus proche et pour acheter des

pièces de rechange, des modes d’emploi ou des accessoires, reportez-vous aux URL suivantes :

In the USA/Aux Etats-Unis http://www.pioneerelectronics.com

In Canada/Aux Canada http://www.pioneerelectronics.ca

S018_B1_EnFr

PIONEER HOME ELECTRONICS CORPORATION

1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan

PIONEER ELECTRONICS (USA) INC.

P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404

PIONEER ELECTRONICS OF CANADA, INC.

340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada TEL: 1-877-283-5901, 905-479-4411

PIONEER EUROPE NV

Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.

253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

5 Arco Lane, Heatherton, Victoria, 3202, Australia, TEL: (03) 9586-6300

PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.

Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico, D.F. 11000 TEL: 55-9178-4270

K002_B3_En

Pioneer Vsx 44 Owners Manual

Navigation menu

Versions of this User Manual:

Views

Navigation