Pismolabs Technology P1093 Pepwave / Peplink / Pismo Wireless Product User Manual Pepwave MAX
Pismo Labs Technology Limited Pepwave / Peplink / Pismo Wireless Product Pepwave MAX
User Manual rev.pdf
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2655569 |
| Application ID | FrBz4TYJsGkLNHY2atTA9g== |
| Document Description | User Manual rev.pdf |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 416.3kB (5203793 bits) |
| Date Submitted | 2015-06-23 00:00:00 |
| Date Available | 2015-06-23 00:00:00 |
| Creation Date | 2015-06-02 11:14:26 |
| Producing Software | Microsoft® Office Word 2007 |
| Document Lastmod | 2015-06-23 14:21:00 |
| Document Title | Pepwave MAX User Manual |
| Document Creator | Microsoft® Office Word 2007 |
| Document Author: | Peplink Ltd. |
Pepwave MAX and Surf User Manual PepwaveProducts: MAX 700/HD2/HD2 IP67/HD2 mini/HD4/BR1/BR1 ENT/BR1 Slim LTE/BR1 IP55/BR2 IP55/On-The-Go MAX HD2/HD4 with MediaFast Surf SOHO Pepwave Firmware 6.2 June 2015 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. Copyright © 2015 Pepwave Ltd. All Rights Reserved. Pepwave and the Pepwave logo are trademarks of Pepwave Ltd. Other brands or products mentioned may be trademarks or registered trademarks of their respective owners. Pepwave MAX and Surf User Manual Table of Contents INTRODUCTION AND SCOPE .............................................................................................. 5 GLOSSARY .......................................................................................................................... 6 PRODUCT FEATURES .......................................................................................................... 7 3.1 3.2 PEPWAVE MAX MOBILE ROUTER OVERVIEW ................................................................... 10 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 4.10 4.11 MAX 700 ................................................................................................................ 10 MAX HD2 ............................................................................................................... 12 MAX HD2 IP67 ....................................................................................................... 14 MAX HD2 MINI ........................................................................................................ 15 MAX HD4 ............................................................................................................... 17 MAX BR1................................................................................................................ 18 MAX BR1 ENT ........................................................................................................ 20 MAX BR1 SLIM LTE .................................................................................................. 22 MAX BR1/2 IP55 .................................................................................................... 24 MAX ON-THE-GO ..................................................................................................... 26 SURF SOHO ............................................................................................................. 27 INSTALLATION ................................................................................................................. 29 5.1 5.2 5.3 SUPPORTED NETWORK FEATURES .................................................................................... 7 OTHER SUPPORTED FEATURES ........................................................................................ 9 PREPARATION ............................................................................................................ 29 CONSTRUCTING THE NETWORK ..................................................................................... 30 CONFIGURING THE NETWORK ENVIRONMENT .................................................................. 31 MOUNTING THE UNIT ...................................................................................................... 32 6.1 6.2 6.3 WALL MOUNT ........................................................................................................... 32 CAR MOUNT ............................................................................................................. 32 IP67 INSTALLATION GUIDE .......................................................................................... 32 CONNECTING TO THE WEB ADMIN INTERFACE ................................................................ 32 CONFIGURINGTHE LAN INTERFACE(S) .............................................................................. 35 8.1 8.2 BASIC SETTINGS ......................................................................................................... 35 CAPTIVE PORTAL ........................................................................................................ 43 CONFIGURINGTHE WAN INTERFACE(S) ............................................................................ 45 9.1 9.2 9.3 9.4 9.5 ETHERNET WAN ....................................................................................................... 46 CELLULAR WAN ........................................................................................................ 54 WI-FI WAN ............................................................................................................. 59 WAN HEALTH CHECK ................................................................................................. 62 DYNAMIC DNS SETTINGS ............................................................................................ 64 http://www.pepwave.com Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 10 ADVANCED WI-FI SETTINGS ............................................................................................. 66 11 MEDIAFAST CONFIGURATION .......................................................................................... 69 11.1 11.2 11.3 SETTING UP MEDIAFAST CONTENT CACHING................................................................... 69 SCHEDULING CONTENT PREFETCHING............................................................................. 70 VIEWING MEDIAFAST STATISTICS .................................................................................. 71 12 BANDWIDTH BONDING SPEEDFUSIONTM/ PEPVPN .......................................................... 72 12.1 12.2 12.3 PEPVPN .................................................................................................................. 72 THE PEPWAVE ROUTER BEHIND A NAT ROUTER .............................................................. 78 SPEEDFUSIONTM STATUS ............................................................................................. 79 13 IPSEC VPN ........................................................................................................................ 80 13.1 IPSEC VPN SETTINGS .................................................................................................. 80 14 OUTBOUND POLICY MANAGEMENT ................................................................................ 84 14.1 14.2 OUTBOUND POLICY .................................................................................................... 84 CUSTOM RULESFOR OUTBOUND POLICY ......................................................................... 85 15 INBOUND ACCESS ............................................................................................................ 94 15.1 PORT FORWARDING SERVICE ........................................................................................ 94 16 NAT MAPPINGS ............................................................................................................... 97 17 QOS 17.1 17.2 17.3 USER GROUPS ........................................................................................................... 99 BANDWIDTH CONTROL .............................................................................................. 100 APPLICATION ........................................................................................................... 100 18 FIREWALL........................................................................................................................102 18.1 18.2 OUTBOUND AND INBOUND FIREWALL RULES ................................................................. 102 WEB BLOCKING ....................................................................................................... 107 19 MISCELLANEOUS SETTINGS .............................................................................................108 19.1 19.2 19.3 19.4 19.5 19.6 HIGH AVAILABILITY ................................................................................................... 108 PPTP SERVER ......................................................................................................... 111 CERTIFICATE MANAGER ............................................................................................. 113 SERVICE FORWARDING .............................................................................................. 113 SERVICE PASSTHROUGH ............................................................................................. 116 GPS FORWARDING................................................................................................... 117 20 AP CONTROLLER .............................................................................................................118 20.1 20.2 20.3 WIRELESS SSID ....................................................................................................... 118 SETTINGS ................................................................................................................ 122 TOOLBOX................................................................................................................ 126 http://www.pepwave.com Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 21 SYSTEM SETTINGS ...........................................................................................................127 21.1 21.2 21.3 21.4 21.5 21.6 21.7 21.8 21.9 21.10 21.11 21.12 21.13 21.14 ADMIN SECURITY ..................................................................................................... 127 FIRMWARE.............................................................................................................. 131 TIME...................................................................................................................... 132 EMAIL NOTIFICATION ................................................................................................ 132 EVENT LOG ............................................................................................................. 134 SNMP................................................................................................................... 135 INCONTROL ............................................................................................................ 137 CONFIGURATION ...................................................................................................... 138 FEATURE ADD-ONS ................................................................................................... 139 REBOOT ................................................................................................................. 139 PING...................................................................................................................... 140 TRACEROUTE TEST .................................................................................................... 141 PEPVPN TEST ......................................................................................................... 141 CLI (COMMAND LINE INTERFACE SUPPORT) .................................................................. 142 22 STATUS ...........................................................................................................................143 22.1 22.2 22.3 22.4 22.5 22.6 22.7 22.8 DEVICE ................................................................................................................... 143 ACTIVE SESSIONS ..................................................................................................... 145 CLIENT LIST ............................................................................................................. 147 WINS CLIENT ......................................................................................................... 147 UPNP / NAT-PMP ................................................................................................. 148 SPEEDFUSION STATUS ............................................................................................... 148 EVENT LOG ............................................................................................................. 152 BANDWIDTH ........................................................................................................... 152 APPENDIX A. RESTORATION OF FACTORY DEFAULTS .......................................................158 APPENDIX B. DECLARATION ............................................................................................159 http://www.pepwave.com Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Introduction and Scope Pepwave routers provide link aggregation and load balancing acrossmultiple WAN connections, allowing a combination of technologies like 3G HSDPA, EVDO, 4G LTE, Wi-Fi, external WiMAX dongle, and satellite to be utilized to connect to the Internet. This manual covers setting up Pepwave routers and provides an introduction to their features and usage. Tips Want to know more aboutPepwave routers? Visit ourYouTube Channel for a video introduction! http://youtu.be/UCkVQThLKO4 http://www.pepwave.com Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Glossary The following terms, acronyms, and abbreviations are frequently used in this manual: Term Definition 3G 3rd Generation standards for wireless communications 4G 4th Generation standards for wireless communications DHCP DNS EVDO HSDPA Dynamic Host Configuration Protocol Domain Name System Evolution-Data Optimized High-Speed Downlink Packet Access HTTP Hyper-Text Transfer Protocol ICMP Internet Control Message Protocol IP LAN MAC Address Internet Protocol Local Area Network Media Access Control Address MTU Maximum Transmission Unit MSS Maximum Segment Size NAT Network Address Translation PPPoE QoS SNMP Point to Point Protocol over Ethernet Quality of Service Simple Network Management Protocol TCP Transmission Control Protocol UDP User Datagram Protocol VPN Virtual Private Network VRRP Virtual Router Redundancy Protocol WAN Wide Area Network WINS Windows Internet Name Service WLAN Wireless Local Area Network http://www.pepwave.com Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Product Features Pepwaverouters enable all LAN users to share broadband Internet connections, and they provide advanced features to enhance Internet access. Below is a list of supported features on Pepwave routers. Features vary by model. For more information, please seepeplink.com/products. 3.1 Supported Network Features 3.1.1 WAN Ethernet WAN connection in full/half duplex Static IP support for PPPoE Built-in HSPA and EVDO cellular modems USB mobile connection(s) Wi-Fi WAN connection Network address translation (NAT)/port address translation (PAT) Inbound and outbound NATmapping IPsec NAT-T and PPTP packet passthrough MAC address clone and passthrough Customizable MTU and MSS values WAN connection health check Dynamic DNS (supportedservice providers: changeip.com, dyndns.org, no-ip.org, tzo.com and DNS-O-Matic) Ping, DNS lookup,and HTTP-based health check 3.1.2 LAN Wi-Fi AP Ethernet LAN ports DHCP server on LAN Extended DHCP option support Static routing rules VLAN on LAN support 3.1.3 VPN PepVPN with SpeedFusionTM PepVPN performance analyzer X.509 certificate support VPN load balancing and failover among selected WAN connections http://www.pepwave.com Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Bandwidth bonding and failover among selected WAN connections IPsec VPN for network-to-network connections (works with Cisco and Juniper only) Ability to route Internet traffic to a remote VPN peer Optional pre-shared key setting SpeedFusionTMthroughput, ping,and traceroute tests PPTP server PPTP and IPsec passthrough 3.1.4 Firewall Outbound (LAN to WAN) firewall rules Inbound (WAN to LAN) firewall rules per WAN connection Intrusion detection and prevention Specification of NAT mappings Outbound firewall rules can be defined by destination domain name 3.1.5 Captive Portal Splash screen of open networks, login page for secure networks Customizable built-in captive portal Supports linking to outside page for captive portal 3.1.6 Outbound Policy Link load distribution per TCP/UDP service Persistent routing for specified source and/or destination IP addresses per TCP/UDP service Traffic prioritization and DSL optimization Prioritize and route traffic to VPN tunnels with Priority and Enforced algorithms 3.1.7 AP Controller Configure and manage Pepwave AP devices Review the status of connected APs 3.1.8 QoS Quality of service for different applications and custom protocols User group classification for different service levels Bandwidth usage control and monitoring on group- and user-level http://www.pepwave.com Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 3.2 Applicationprioritization for custom protocols and DSL/cable optimization Other Supported Features User-friendly web-based administration interface HTTP and HTTPS support for web admin interface Configurable web administration port and administrator password Firmware upgrades, configuration backups, ping, and traceroute via web admin interface Remote web-based configuration (via WAN and LAN interfaces) Time server synchronization SNMP Email notification Read-only user for web admin SharedIP drop-in mode Authentication and accounting by RADIUS server for web admin Built-in WINS servers* Syslog SIP passthrough PPTP packet passthrough Event log Active sessions Client list WINS client list * UPnP / NAT-PMP Real-time, hourly, daily,and monthly bandwidth usage reports and charts IPv6 support Support USB tethering on Android 2.2+ phones * Not supported on MAX Surf-On-The-Go, Surf SOHO, and BR1 variants http://www.pepwave.com Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Pepwave MAX Mobile Router Overview 4.1 MAX 700 4.1.1 Panel Appearance http://www.pepwave.com 10 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 4.1.2 LED Indicators The statuses indicated by the front panel LEDs are as follows: Status Wi-Fi WAN Wi-Fi AP OFF Red Blinking red Green Status Indicators System initializing Booting up or busy Boot up error Ready Wi-Fi AP and Wi-Fi WAN Indicators OFF Disconnected Blinking slowly Connecting to network Blinking Connected to network with traffic ON Connected to network without traffic OFF Disabled Blinking slowly Enabled but no client connected Blinking Connected to network with traffic ON Client(s) connected to wireless network LAN and Ethernet WAN Ports Green LED Orange LED Port Type ON 10 / 100/ 1000 Mbps Blinking Data is transferring No data is being transferred or port is not connected OFF Auto MDI/MDI-X ports http://www.pepwave.com 11 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 4.2 MAX HD2 4.2.1 Panel Appearance http://www.pepwave.com 12 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 4.2.2 LED Indicators The statuses indicated by the front panel LEDs are as follows: Status Wi-Fi WAN / Cellular 1 / Cellular 2 OFF Red Blinking red Green Status Indicators System initializing Booting up or busy Boot up error Ready Wi-Fi AP and Wi-Fi WAN Indicators OFF Disabled Intermittent Blinking slowly Connecting to wireless network(s) Blinking Connected to wireless network(s) with traffic ON Connected to wireless network(s) without traffic LAN and Ethernet WAN Ports Green LED Orange LED Port Type ON 10 / 100 / 1000 Mbps Blinking Data is transferring No data is being transferred or port is not connected OFF Auto MDI/MDI-X ports http://www.pepwave.com 13 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 4.3 MAX HD2 IP67 4.3.1 Panel Appearance The statuses indicated by the front panel LEDs are as follows: Status OFF Red Blinking red Green http://www.pepwave.com Status Indicators System initializing Booting up or busy Boot up error Ready 14 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 4.4 MAX HD2 mini 4.4.1 Panel Appearance http://www.pepwave.com 15 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 4.4.2 LED Indicators The statuses indicated by the front panel LEDs are as follows: Status Cellular 1 / Cellular 2 OFF Red Blinking red Green Status Indicators System initializing Booting up or busy Boot up error Ready Cellular WAN Indicators OFF Disabled intermittent Blinking slowly Connecting to wireless network(s) Blinking Connected to wireless network(s) with traffic ON Connected to wireless network(s) without traffic LAN and Ethernet WAN Ports Green LED Orange LED Port Type ON 10 / 100 / 1000 Mbps Blinking Data is transferring No data is being transferred or port is not connected OFF Auto MDI/MDI-X ports http://www.pepwave.com 16 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 4.5 MAX HD4 4.5.1 Panel Appearance 4.5.2 LED Indicators The statuses indicated by the front panel LEDs are as follows: Status Wi-Fi WAN / Cellular 1 / Cellular 2 OFF Red Blinking red Green Status Indicators System initializing Booting up or busy Boot up error Ready Wi-Fi AP and Wi-Fi WAN Indicators OFF Disabled Intermittent Blinking slowly Connecting to wireless network(s) Blinking Connected to wireless network(s) with traffic ON Connected to wireless network(s) without traffic LAN and Ethernet WAN Ports Green LED Orange LED Port Type ON 10 / 100 / 1000 Mbps Blinking Data is transferring No data is being transferred or port is not connected OFF Auto MDI/MDI-X ports http://www.pepwave.com 17 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 4.6 MAX BR1 4.6.1 Panel Appearance 4.6.2 LED Indicators The statuses indicated by the front panel LEDs are as follows: Status Wi-Fi OFF Red Blinking red Green OFF Blinking slowly Blinking ON http://www.pepwave.com Status Indicators System initializing Booting up or busy Boot up error Ready Wi-Fi Indicators Disabled intermittent Connecting to wireless network(s) Connected to wireless network(s) with traffic Connected to wireless network(s) without traffic 18 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Cellular Cellular Indicators Disabled or no SIM card inserted Connecting or connected to network(s) OFF ON LAN and Ethernet WAN Ports Green LED Orange LED Port Type ON 100 Mbps OFF 10 Mbps ON Port is connected without traffic Blinking OFF Data is transferring Port is not connected Auto MDI/MDI-X ports http://www.pepwave.com 19 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 4.7 MAX BR1 ENT 4.7.1 Panel Appearance 4.7.2 LED Indicators The statuses indicated by the front panel LEDs are as follows: Status Cellular OFF Red Blinking red Green Status Indicators System initializing Booting up or busy Boot up error Ready Cellular WAN Indicators OFF Disabled intermittent Blinking slowly Connecting to wireless network(s) Blinking Connected to wireless network(s) with traffic ON Connected to wireless network(s) without traffic http://www.pepwave.com 20 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual LAN and Ethernet WAN Ports Green LED Orange LED Port Type ON 10 / 100 / 1000 Mbps Blinking Data is transferring No data is being transferred or port is not connected OFF Auto MDI/MDI-X ports http://www.pepwave.com 21 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 4.8 MAX BR1 Slim LTE 4.8.1 Panel Appearance 4.8.2 LED Indicators The statuses indicated by the front panel LEDs are as follows: Status Wi-Fi Cellular OFF Red Blinking red Green OFF Blinking slowly Blinking ON Status Indicators System initializing Booting up or busy Boot up error Ready Wi-Fi Indicators Disabled intermittent Connecting to wireless network(s) Connected to wireless network(s) with traffic Connected to wireless network(s) without traffic Cellular WAN Indicators OFF Disabled intermittent Blinking slowly Connecting to wireless network(s) Connected to wireless network(s) with traffic Blinking ON Connected to wireless network(s) without traffic http://www.pepwave.com 22 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual LAN and Ethernet WAN Ports Green LED Orange LED Port Type ON 10 / 100 / 1000 Mbps Blinking Data is transferring No data is being transferred or port is not connected OFF Auto MDI/MDI-X ports http://www.pepwave.com 23 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 4.9 MAX BR1/2 IP55 4.9.1 Panel Appearance 4.9.2 LED Indicators The statuses indicated by the front panel LEDs are as follows: Status OFF Red Blinking red Green http://www.pepwave.com Status Indicators System initializing Booting up or busy Boot up error Ready 24 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Wi-Fi Cellular OFF Blinking slowly Blinking ON Wi-Fi Indicators Disabled Intermittent Connecting to wireless network(s) Connected to wireless network(s) with traffic Connected to wireless network(s) without traffic Cellular Indicators Disabled or no SIM card inserted Connecting or connected to network(s) OFF ON LAN and Ethernet WAN Ports Green LED Orange LED Port Type ON 100 Mbps OFF 10 Mbps ON Port is connected without traffic Blinking OFF Data is transferring Port is not connected Auto MDI/MDI-X ports http://www.pepwave.com 25 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 4.10 MAX On-The-Go 4.10.1 Panel Appearance 4.10.2 LED Indicators The statuses indicated by the front panel LEDs are as follows: WAN Wi-Fi Status Cellular Indicators Modem is not attached to the port Modem is attached to the port OFF Green Wi-Fi Indicators Disconnected from AP Connected to AP OFF Green Status Indicators System initializing Booting up or busy Ready OFF Red Green LAN and Ethernet WAN Ports Green LED Orange LED Port Type ON 100 Mbps OFF 10 Mbps ON Port is connected without traffic Blinking Data is transferring Auto MDI/MDI-X ports http://www.pepwave.com 26 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 4.11 Surf SOHO 4.11.1 Panel Appearance 4.11.2 LED Indicators The statuses indicated by the front panel LEDs are as follows: Wi-Fi Status OFF Blinking ON Continuous blinking OFF Red Green Wi-Fi and Status Indicators DisabledIntermittent Enabled but no client connected Client(s) connected to wireless network Transferring data to wireless network System initializing Booting up or busy Ready state LAN and Ethernet WAN Ports Green LED ON http://www.pepwave.com 10 / 100 Mbps 27 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Blinking Orange LED Port type OFF Data is transferring No data is being transferred or port is not connected Auto MDI/MDI-X ports Wi-Fi Signal Off Signal strength No connection Wi-Fi signal strength (low, medium, and high) http://www.pepwave.com 28 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Installation The following section details connecting Pepwave routersto your network. 5.1 Preparation Before installingyour Pepwave router, please prepare the following as appropriate for your installation: At least one Internet/WAN access account and/or Wi-Fi access information Depending on network connection type(s), one or more of the following: Ethernet WAN: A 10/100/1000BaseT UTP cable with RJ45 connector USB: A USB modem Embedded modem: A SIM card for GSM/HSPA service Wi-Fi WAN: Wi-Fi antennas PC Card/Express Card WAN:A PC Card/ExpressCard for the corresponding card slot A computer installed with the TCP/IP network protocol and a supported web browser. Supported browsers include Microsoft Internet Explorer 8.0 or above, Mozilla Firefox 10.0 or above, Apple Safari 5.1 or above, and Google Chrome 18 or above. http://www.pepwave.com 29 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 5.2 Constructing the Network At ahigh level, construct the network according to the following steps: 1. 2. 3. With an Ethernet cable, connect a computer to one of the LAN ports on thePepwave router. Repeat with different cables for up to 4 computers to be connected. With another Ethernet cable or a USB modem/Wi-Fi antenna/PC Card/Express Card, connect to one of the WAN ports on the Pepwave router. Repeat the same procedure for other WAN ports. Connect the power adapter to the power connector on the rear panel ofthe Pepwave router, and then plug it into a power outlet. The following figure schematically illustrates the resulting configuration: http://www.pepwave.com 30 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 5.3 Configuring the Network Environment To ensure that the Pepwave routerworks properly in the LAN environment and can access the Internet via WAN connections, please refer to the following setup procedures: LAN configuration For basic configuration, refer to Section7,Connecting to the Web Admin Interface. For advanced configuration, go to Section8, Configuringthe LAN Interface(s). WAN configuration For basic configuration, refer to Section7, Connecting to the Web Admin Interface. For advanced configuration, go to Section 8.2,Captive Portal. http://www.pepwave.com 31 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Mounting the Unit 6.1 Wall Mount The Pepwave MAX 700/HD2/On-The-Go can be wall mounted using screws. After adding the screw on the wall, slide the MAX in the screw hole socket as indicated below.Recommeneded screw specification: M3.5 x 20mm, head diameter 6mm, head thickness 2.4mm. The Pepwave MAX BR1 requires four screws for wall mounting. 6.2 Car Mount The Pepwave MAX700/HD2 can be mounted in a vehicle using the included mounting brackets. Place the mounting brackets by the two sides and screw them onto the device. 6.3 IP67 Installation Guide Installation instructions for IP67 devices can be found here: http://download.peplink.com/manual/IP67_Installation_Guide.pdf Connecting to the Web Admin Interface http://www.pepwave.com 32 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 1. Start a web browser on a computer that is connected with the Pepwave router through theLAN. 2. To connect to the router’s web admin interface, enter the following LAN IP address in the address field of the web browser: http://192.168.50.1 (This is the default LAN IP address forPepwave routers.) 3. Enter the following to access the web admin interface. Username: admin Password: admin (This is the default username and password forPepwave routers. The admin and read-only user passwords can be changed at System>Admin Security.) 4. After successful login, the Dashboard will be displayed. The Dashboard shows current WAN, LAN,and Wi-Fi AP statuses. Here, youcan change WAN connection priorityand switch on/off the Wi-Fi AP. For further information on setting up these connections, please refer to Sections8and9. Device Informationdisplays details about the device, including model name, firmwareversion, and uptime. For further information, please refer to Section 22. http://www.pepwave.com 33 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Important Note Configuration changes (e.g. WAN, LAN, admin settings, etc.) will take effect only after clicking the Save button at the bottom of each page. The Apply Changes button causes the changes to be saved and applied. http://www.pepwave.com 34 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Configuringthe LAN Interface(s) 8.1 Basic SettingsC:\Users\Allen Tam\Documents\LAN_Basic_Settings LAN interface settings are located atNetwork>LAN>Basic Settings. IP Settings IP Address The IP address and subnet mask of thePepwave routeron the LAN. Port Settings Speed This is the port speed of the LAN interface. It should be set to the same speed as the connected device to avoid port negotiation problems.When a static speed is set, you may choose whether to advertise its speed to the peer device. Advertise Speed is selected by default. You can choose not to advertise the port speed if the port has difficulty negotiating with the peer device. http://www.pepwave.com 35 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Drop-in Mode Settings Enable Drop-in mode eases the installation of Peplink routerson a live network between the existing firewall and router, such that no configuration changes are required on existing equipment. Check the box to enable the drop-in mode feature, if available on your model. WAN for DropIn Mode Select the WAN port to be used for drop-in mode. If WAN 1 with LAN Bypass is selected, the high availability feature will be disabled automatically. Share Drop-In IPA Shared IP AddressA WAN Default Gateway WAN DNS Servers When this option is enabled, the passthrough IP address will be used to connect to WAN hosts (email notification, remote syslog, etc.). The Pepwaverouter will listen for this IP address when WAN hosts access services provided by the Pepwaverouter (web admin access from the WAN, DNS server requests, etc.). To connect to hosts on the LAN (email notification, remote syslog, etc.), the default gateway address will be used. The Pepwaverouter will listen for this IP address when LAN hosts access services provided by the Pepwaverouter (web admin access from the WAN, DNS proxy, etc.). Access to this IP address will be passed through to the LAN port if this device is not serving the service being accessed. The shared IP address will be used in connecting to hosts on the WAN (email notification, remote syslog, etc.) The device will also listen on the IP address when hosts on the WAN access services served on this device (web admin access from the WAN, DNS server, etc.) Enter the WAN router's IP address in this field. If there are more hosts in addition to the router on the WAN segment, check the I have other host(s) on WAN segment box and enter the IP address of the hosts that need to access LAN devices or be accessed by others. Enter the selected WAN's corresponding DNS server IP addresses. - Advanced feature, please click the http://www.pepwave.com button on the top right-hand corner to activate. 36 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual DHCP Server Settings DHCP Server When this setting is enabled, the DHCP server automatically assigns an IP address to each computer that is connected via LAN and configured to obtain an IP address via DHCP. The Pepwave router’s DHCP server can prevent IP address collision on the LAN. IP Range & Subnet Mask Thesesettings allocate a range of IP addresses that will be assigned to LAN computers by the Pepwave router’s DHCP server. Lease Time This setting specifies the length of time throughout which an IP address of a DHCP client remains valid. Upon expiration of the lease time, the assigned IP address will no longer be valid and renewal of the IP address assignment will be required. DNS Servers This option allows you to input the DNS server addresses to be offered to DHCP clients. If Assign DNS server automatically is selected, the Pepwave router’s built-in DNS server address (i.e., LAN IP address) will be offered. WINS Server This option allows you to optionally specify aWindows Internet Name Service (WINS) server. You may choose to use the built-in WINS server or external WINS servers. When this unit is connected using SpeedFusionTM, other VPN peers can share this unit's built-in WINS server by entering this unit's LAN IP address in their DHCP WINS Server setting. Afterward, all PC clients in the VPN can resolve the NetBIOS names of other clients in remote peers.If you have enabled this option, a list of WINS clients will be displayed at Status>WINS Clients. BOOTP Extended DHCP Option DHCP Reservation Check this box to enable BOOTP on older networks that still require it. In addition to standard DHCP options (e.g., DNS server address, gateway address, subnet mask), you can specify the value of additional extended DHCP options, as defined in RFC 2132. With these extended options enabled, you can pass additional configuration information to LAN hosts. To define an extended DHCP option, click the Add button, choose the option to define and enter its value. For values that are in IP address list format, you can enter one IP address per line in the provided text area input control. Each option can be defined once only. This setting reserves the assignment of fixed IP addresses for a list of computers on the LAN. The computers to be assigned fixed IP addresses on the LAN are identified by their MAC addresses. The fixed IP address assignment is displayed as a cross-reference list between the computers’ names, MAC addresses, and fixed IP addresses. Name (an optional field) allows you to specify a name to represent the device. MAC addresses should be in the format of 00:AA:BB:CC:DD:EE. Press to create a new record. Press to remove a record. Reserved client information can be imported from the Client List, located atStatus>Client List. For more details, please refer to Section22.3. Static Route Settings Static Route This table is for defining static routing rules for the LAN segment. A static route consists of the network address, subnet mask, and gateway address. The address and subnet mask values are in w.x.y.zformat. The local LAN subnet and subnets behind the LAN will be advertised to the VPN. Remote routes sent over the VPN will also be accepted. Any VPN member will be able to route to http://www.pepwave.com 37 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual the local subnets.Press to create a new route. Press to remove a route. WINS Server Settings Enable Check the box to enable the WINS server. A list of WINS clients will be displayed at Status>WINS Clients. DNS Proxy Settings Enable To enable the DNS proxy feature, check this box, and then set up the feature at Network>LAN>DNS Proxy Settings.A DNS proxy server can be enabled to serve DNS requests originating from LAN/PPTP/SpeedFusionTMpeers. Requests are forwarded to the DNS servers/resolvers defined for each WAN connection. DNS Caching This field is to enable DNS caching on the built-in DNS proxy server. When the option is enabled, queried DNS replies will be cached until the records’ TTL has been reached. This feature can help improve DNS lookup time. However, it cannot return the most up-to-dateresult for those frequently updated DNS records.By default, DNS Caching is disabled. Include Google Public DNS Servers When this option is enabled, the DNS proxy server will also forward DNSrequests to Google's Public DNS Servers, in addition to the DNS servers defined in each WAN. This could increase the DNS service's availability. This setting is disabled by default. Local DNS Records This table is for defining custom local DNS records. A static local DNS record consists of a host name and IP address. When looking up the host name from the LAN to LAN IP of the Pepwave router, the corresponding IP address will be http://www.pepwave.com 38 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual returned.Press DNS Resolvers A to create a new record. Press to remove a record. Check the box to enable the WINS server. A list of WINS clients will be displayed at Network>LAN>DNS Proxy Settings>DNS Resolvers.This field specifies which DNS resolvers will receive forwarded DNS requests. If no WAN/VPN/LAN DNS resolver is selected, all of the WAN’s DNS resolvers will be selected. If a SpeedFusionTMpeer is selected, you may enter the VPN peer’s DNS resolver IP address(es).Queries will be forwarded to the selected connections’ resolvers. If all of the selected connections are down, queries will be forwarded to all resolvers on healthy WAN connections. - Advanced feature, please click the button on the top right hand corner to activate. Finally, if needed, configure Bonjour forwarding, Apple’s zero configuration networking protocol. Once VLAN configuration is complete, click Save to store your changes. Bonjour Forwarding Settings Enable Bonjour Service Check this box to turn on Bonjour forwarding. Choose Service and Client networks from the drop-down menus, and then click add the networks. To delete an existing Bonjour listing, click http://www.pepwave.com 39 to Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual To enable VLAN configuration, click the button in the IP Settings section. To add a new LAN, click the New LAN button. To change LAN settings, click the name of the LAN to change under the LAN heading. The following settings are displayed when creating a new LAN or editing an existing LAN. IP Settings IP Address & Subnet Mask Enter the Pepwave router’s IP address and subnet mask values to be used on the LAN. Network Settings Name VLAN ID Inter-VLAN routing Captive Portal Enter a name for the LAN. Enter a number for your VLAN. Check this box to enable routing between virtual LANs. Check this box to turn on captive portals. http://www.pepwave.com 40 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Layer 2 PepVPN Bridging PepVPN Profiles to Bridge Spanning Tree Protocol Override IP Address when bridge connected The remote network of the selected PepVPN profiles will be bridged with this local LAN, creating a Layer 2 PepVPN, they will be connected and operate like a single LAN, and any broadcast or multicast packets will be sent over the VPN. Click the box will enable STP for this layer 2 profile bridge. Select "Do not override" if the LAN IP address and local DHCP server should remain unchanged after the Layer 2 PepVPN is up. If you choose to override IP address when the VPN is connected, the device will not act as a router, and most Layer 3 routing functions will cease to work. DHCP Server Settings DHCP Server When this setting is enabled, the Pepwave router’s DHCP server automatically assigns an IP address to each computer that is connected via LAN and configured to obtain an IP address via DHCP. The Pepwave router’s DHCP server can prevent IP address collisions on the LAN. To enable DHCP bridge relay, please click the IP Range & Subnet Mask icon on this menu item. These settings allocate a range of IP address that will be assigned to LAN computers by the Pepwave router’s DHCP server. Lease Time This setting specifies the length of time throughout which an IP address of a DHCP client remains valid. Upon expiration of Lease Time, the assigned IP address will no longer be valid and the IP address assignment must be renewed. DNS Servers This option allows you to input the DNS server addresses to be offered to DHCP clients. If Assign DNS server automatically is selected, the Pepwave router’s built-in DNS server address (i.e., LAN IP address) will be offered. http://www.pepwave.com 41 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual WINS Servers BOOTP Extended DHCP Option DHCP Reservation This option allows you to specify the Windows Internet Name Service (WINS) server. You may choose to use the built-in WINS server or external WINS servers. When this unit is connected using SpeedFusionTM, other VPN peers can share this unit's built-in WINS server by entering this unit's LAN IP address in their DHCP WINS Servers setting. Therefore, all PC clients in the VPN can resolve the NetBIOS names of other clients in remote peers.If you have enabled this option, a list of WINS clients will be displayed at Status>WINS Clients. Check this box to enable BOOTP on older networks that still require it. In addition to standard DHCP options (e.g. DNS server address, gateway address, subnet mask), you can specify the value of additional extended DHCP options, as defined in RFC 2132. With these extended options enabled, you can pass additional configuration information to LAN hosts.To define an extended DHCP option, click the Add button, choose the option to define, and then enter its value. For values that are in IP address list format, you can enter one IP address per line in the provided text area input control. Each option can be defined once only. This setting reserves the assignment of fixed IP addresses for a list of computers on the LAN. The computers to be assigned fixed IP addresses on the LAN are identified by their MAC addresses. The fixed IP address assignment is displayed as a cross-reference list between the computers’ names, MAC addresses, and fixed IP addresses. Name (an optional field) allows you to specify a name to represent the device. MAC addresses should be in the format of 00:AA:BB:CC:DD:EE. Press to create a new record. Press to remove a record.Reserved clients information can be imported from the Client List, located atStatus>Client List. For more details, please refer to Section22.3. To configure DHCP relay, first click the to display the settings. button found next to the DHCP Server option DHCP Relay Settings Enable Check this box to turn on DHCP relay. Click the icon to disable DHCP relay. DHCP Server IP Address Enter the IP addresses of one or two DHCP servers in the provided fields. The DHCP servers entered here will receive relayed DHCP requests from the LAN. For active-passive DHCP server configurations, enter active and passive DHCP server relay IP addresses in DHCP Server 1 and DHCP Server 2. DHCP Option 82 DCHP Option 82 includes device information as relay agent for the attached client when forwarding DHCP requests from client to server. This option also embeds the device’s MAC address and network name in circuit and remote IDs. Check this box to enable DHCP Option 82. Once DHCP is set up, configure LAN Physical Settings, Static Route Settings, WINS Server Settings, and DNS Proxy Settings as noted above. http://www.pepwave.com 42 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 8.2 Captive Portal The captive portal serves as gateway that clients have to pass if they wish to access the internet using your router. To configure, navigate to Network>LAN>Captive Portal. Captive Portal Settings Enable Hostname Access Mode Check Enable and then, optionally, select the LANs/VLANs that will use the captive portal. To customize the portal’s form submission and redirection URL, enter a new URL in this field. To reset the URL to factory settings, click Default. Click Open Access to allow clients to freely access your router. Click User Authentication to force your clients to authenticate before accessing your router. This authenticates your clients through a RADIUS server. After selecting this option, you will see the following fields: RADIUS Server Fill in the necessary information to complete your connection to the server and enable authentication. This authenticates your clients through a LDAP server. Upon selecting this option, you will see the following fields: LDAP Server Fill in the necessary information to complete your connection to the server and enable authentication. http://www.pepwave.com 43 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Access Quota Quota Reset Time Allowed Networks Splash Page Set a time and data cap to each user’s Internet usage. This menu determines how your usage quota resets. Setting it to Daily will reset it at a specified time every day. Setting a number of minutes after quota reached establish a timer for each user that begins after the quota has been reached. To whitelist a network, enter the domain name / IP address here and click delete an existing network from the list of allowed networks, click the to the listing. . To button next Here, you can choose between using thePepwave router’s built-in captive portal and redirecting clients to a URL you define. The Portal Customization menu has two options: and . Clicking displays a pop-up previewing the captive portal that your clients will see. Clicking displays the following menu: http://www.pepwave.com 44 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Portal Customization Logo Image Message Terms & Conditions Custom Landing Page Click the Choose File button to select a logo to use for the built-in portal. If you have any additional messages for your users, enter them in this field. If you would like to use your own set of terms and conditions, please enter them here. If left empty, the built-in portal will display the default terms and conditions. Fill in this field to redirect clients to an external URL. Configuringthe WAN Interface(s) WAN Interface settings are located at Network>WAN. To reorder WAN priority, drag on the appropriate WAN by holding the left mouse button, move it to the desired priority (the first one would be the highest priority, the second one would be lower priority, and so on), and drop it by releasing the mouse button. To disable a particular WAN connection, drag on the appropriate WAN by holding the left mouse button, move it the Disabledrow, and drop it by releasing the mouse button. You can also set priorities on the Dashboard.Click the Details button in the corresponding row to modify the connection setting. Important Note Connection details will be changed and become effective immediatelyafterclicking the Save and Apply button. http://www.pepwave.com 45 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 9.1 Ethernet WAN FromNetwork>WAN, choose a WAN connection and then click Details. WAN Port (Section 1) WAN Connection Name Entera name to represent this WAN connection. There are three possible connection methods for Ethernet WAN: Connection Method DHCP Static IP PPPoE The connection method and details are determined by, and can be obtained from, the ISP.See the following sections for details oneach connection method. Routing Mode IP Address/Subnet Mask/Default Gateway Hostname DNS Servers This field shows that NAT (network address translation) will be applied to the traffic routed over this WAN connection. IP Forwarding is available when you click the link in the help text. Enter the WAN IP address and subnet mask, as well as the IP address of the default gateway, in these fields. Enter a hostname for this WAN port if needed. Select a DNS server for this port to use. This port can either be automatically selected or manually designated. http://www.pepwave.com 46 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual WAN Port (Section 2) Standby State This setting specifies the standby state of the WAN connection. The available options are Remain connected and Disconnect.The default state is Remain Connected. Upstream Bandwidth This setting specifies the data bandwidth in the outbound direction from the LAN through the WAN interface. Downstream Bandwidth This setting specifies the data bandwidth in the inbound direction from the WAN interface to the LAN. This value is referenced as the default weight value when using the algorithm Least Used or the algorithm Persistence (Auto) in outbound policy with Managed by Custom Rules chosen (see Section 14.2). Health Check Method This setting specifies the health check method for the WAN connection. The value of method can be configured as Disabled, Ping, DNS Lookup,or HTTP. The default method is Disabled.See Section9.4 for configuration details. These fields are for specifying the target DNS servers where DNS lookups will be sent to for health check. Health Check DNS Servers If the box Use first two DNS servers as Health Check DNS Servers is checked, the first two DNS servers will be the DNS lookup targets for checking the connection healthiness. If the box is not checked, the field Host 1 must be filled and the field Host 2 is optional. The connection is considered to be up if DNS responses are received from any one of the health check DNS servers, regardless of whether the result is positive or negative. Timeout If a health check test cannot be completed within the specified amount of time, the test will be treated as failed. http://www.pepwave.com 47 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Health Check Interval This is the number of consecutive check failures before treating a connection as down. Health Check Retries This is the number of consecutive check failures before treating a connection as down. Recovery Retries This is the number of responses required after a health check failure before treating a connection as up again. WAN Port (Section 3) This setting specifies the dynamic DNS service provider to be used for the WAN based on supported dynamic DNS service providers: Dynamic DNS Service Provider changeip.com dyndns.org no-ip.org tzo.com DNS-O-Matic Select Disabled to disable this feature.See Section9.5 for configuration details. Bandwidth Allowance Monitor This option enables bandwidth usage monitoring on this WAN connection for each billing cycle. When this setting is not enabled, each month’s bandwidth usage is tracked, but no action will be taken. Port Speed This setting specifies port speed and duplex configurations of the WAN port.By default, Auto is selected and the appropriate data speed is automatically detected by the Pepwave router.In the event of negotiation issues, the port speed can be manually specified. You can also choose whether or not to advertise the speed to the peer by selecting the Advertise Speed checkbox. MTU This setting specifies the maximum transmission unit.By default, MTU is set to Custom 1440.You may adjust the MTU value by editing the text field. Click Default to restore the default MTU value. Select Auto and the appropriate MTU value will be automatically detected. Auto-detection will run each time the WAN connection establishes. http://www.pepwave.com 48 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual WAN Port (Section 4) MSS This setting should be configured based on the maximum payload size that the local system can handle. The MSS (maximum segment size) is computed from the MTU minus 40 bytes for TCP over IPv4.If MTU is set to Auto, the MSS will also be set automatically.By default, MSS is set to Auto. MAC Address Clone Some service providers (e.g., cable providers) identify the client’s MAC address and require the client to always use the same MAC address to connect to the network. In such cases, change the WAN interface’s MAC address to the original client PC’s MAC addressvia this field. The default MAC address is a unique value assigned at the factory. In most cases, the default value is sufficient. Clicking Default restores the MAC address to the default value. VLAN Click the square if you wish to enable VLAN functionality and enable multiple broadcast domains. Once you enable VLAN, you will be able to enter a name for your network. Reply to ICMP PING If this field is disabled, the WAN connection will not respond to ICMP ping requests. By default, this is enabled. Additional Public IP Address The IP Addresslist represents the list of fixed Internet IP addresses assigned by the ISP, in the event that more than one Internet IP address is assigned to this WAN connection.Enter the fixed Internet IP addresses and the corresponding subnet mask, and then click the Down Arrow button to populate IP address entries to the IP Address List. http://www.pepwave.com 49 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual IPv6 IPv6 IPv6 support can be enabled on one of the available Ethernet WAN ports. On this screen, you can choose which WAN will support IPv6.To enable IPv6 support on a WAN, the WAN router must respond to stateless address auto configuration advertisements and DHCPv6 requests. IPv6 clients on the LAN will acquire their IPv6, gateway, and DNS server addresses from it. The device will also acquire an IPv6 address for performing ping/traceroute checks and accepting web admin accesses.Note: This feature is only available on the Pepwave MAX 700,HD2, and HD2 IP67. 9.1.1 DHCP Connection There are three possible connection methods: 1. DHCP 2. Static IP 3. PPPoE 4. L2TP The DHCP connection method is suitable if the ISP provides an IP address automatically usingDHCP (e.g.,satellite modem, WiMAX modem, cable, Metro Ethernet, etc.). DHCP Connection Settings Routing Mode IP Address/ Subnet Mask/ Default Gateway NAT allows substituting the real address in a packet with a mapped address that is routable on the destination network. By clicking the help icon in this field, you can display the IP Forwarding option, if your network requires it. This information is obtained from the ISP automatically. http://www.pepwave.com 50 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Hostname (Optional) DNS Servers If your service provider's DHCP server requires you to supply a hostname value upon acquiring an IP address, you may enter the value here. If your service provider does not provide you with the value, you can safely bypass this option. Each ISP may provide a set of DNS servers for DNS lookups. This setting specifies the DNS (Domain Name System) servers to be used when a DNS lookup is routed through this connection. Selecting Obtain DNS server address automatically results in the DNS servers being assigned by the WAN DHCP server to be used for outbound DNS lookups over the connection. (The DNS servers are obtained along with the WAN IP address assigned from the DHCP server.) When Use the following DNS server address(es) is selected, you may enter custom DNS server addresses for this WAN connection into the DNS Server 1 and DNS Server 2 fields. 9.1.2 Static IP Connection Thestatic IP connection method is suitable if your ISP provides a static IP address to connect directly. Static IP Settings Routing Mode NAT allows substituting the real address in a packet with a mapped address that is routable on the destination network. By clicking the help icon in this field, you can display the IP Forwarding option, if your network requires it. IP Address / Subnet Mask / Default Gateway These settings allow you to specify the information required in order tocommunicate on the Internet via a fixed Internet IP address.The information is typically determined by and can be obtained from the ISP. DNS Servers Each ISP may provide a set of DNS servers for DNS lookups. This setting specifies the DNS (Domain Name System) servers to be used when a DNS lookup is routed through this connection. Selecting Obtain DNS server address automatically results in the DNS servers being assigned by the WAN DHCP server to be used for outbound DNS lookups over the connection. (The DNS servers are obtained along with the WAN IP address assigned from the DHCP server.)When Use the following DNS server address(es) is selected, you may enter custom DNS server addresses for this WAN connection into the DNS Server 1 and DNS Server 2 fields. http://www.pepwave.com 51 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 9.1.3 PPPoE Connection This connection method is suitable if your ISP provides a login ID/password to connect via PPPoE. PPPoE Settings Routing Mode IP Address / Subnet Mask / Default Gateway PPPoE User Name / Password Confirm PPPoE Password NAT allows substituting the real address in a packet with a mapped address that is routable on the destination network. By clicking the help icon in this field, you can display the IP Forwarding option, if your network requires it. This information is obtained from the ISP automatically. Enter the required information in these fields in order to connect via PPPoE to the ISP. The parameter values are determined by and can be obtained from the ISP. Verify your password by entering it again in this field. Service Name (Optional) Service name is provided by the ISP. Note: Leave this field blank unless it is provided by your ISP. IP Address (Optional) If your ISP provides a PPPoE IP address, enter it here. Note: Leave this field blank unless it is provided by your ISP. DNS Servers Each ISP may provide a set of DNS servers for DNS lookups. This setting specifies the DNS (Domain Name System) servers to be used when a DNS lookup is routed through this connection. Selecting Obtain DNS server address automatically results in the DNS servers being assigned by the WAN DHCP server to be used for outbound DNS lookups over the connection. (The DNS servers are obtained along with the WAN IP address assigned from the DHCP server.)When Use the following DNS server address(es) is selected, you may enter custom DNS server addresses for this WAN http://www.pepwave.com 52 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual connection into the DNS Server 1 and DNS Server 2 fields. L2TP Settings L2TP User Name / Password Confirm L2TP Password Enter the required information in these fields in order to connect via L2TP to your ISP. The parameter values are determined by and can be obtained from your ISP. Verify your password by entering it again in this field. Server IP Address / Host L2TP server address is a parameter which is provided by your ISP. Note: Leave this field blank unless it is provided by your ISP. Address Type Your ISP will also indicate whether the server IP address is Dynamic or Static. Please click the appropriate value. Each ISP may provide a set of DNS servers for DNS lookups. This setting specifies the DNS (Domain Name System) servers to be used when a DNS lookup is routed through this connection. DNS Servers Selecting Obtain DNS server address automatically results in the DNS servers assigned by the PPPoE server to be used for outbound DNS lookups over the WAN connection. (The DNS servers are obtained along with the WAN IP address assigned from the PPPoE server.) When Use the following DNS server address(es) is selected, you can enter custom DNS server addresses for this WAN connection into the DNS server 1 and DNS server 2 fields. http://www.pepwave.com 53 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 9.2 Cellular WAN To access cellular WAN settings, click Network>WAN>Details. (Available on the Pepwave MAX BR1, HD2, and HD2 IP67 only) Cellular Status IMSI This is the International Mobile Subscriber Identity which uniquely identifies the SIM card. This is applicable to 3G modems only. MEID SomePepwave routerssupport both HSPA and EV-DO. For Sprint or Verizon Wireless EV-DO users, a unique MEID identifier code (in hexadecimal format) is used by the carrier to associate the EV-DO device with the user.This information is presented in hex and decimal format. ESN This serves the same purpose as MEID HEX but uses an older format. IMEI This is the unique ID for identifying the modem in GSM/HSPA mode. http://www.pepwave.com 54 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual WAN Connection Settings WAN Connection Name Enter a name to represent this WAN connection. Network Mode Users have to specify the network they are on accordingly. Routing Mode This option allows you to select the routing method to be used in routing IP frames via the WAN connection. The mode can be either NAT (network address translation) or IP Forwarding. Click the button to enable IP forwarding. Each ISP may provide a set of DNS servers for DNS lookups. This setting specifies the DNS (Domain Name System) servers to be used when a DNS lookup is routed through this connection. DNS Servers Selecting Obtain DNS server address automatically results in the DNS servers assigned by the PPPoE server to be used for outbound DNS lookups over the WAN connection. (The DNS servers are obtained along with the WAN IP address assigned from the PPPoE server.) When Use the following DNS server address(es) is selected, you can enter custom DNS server addresses for this WAN connection into the DNS server 1 and DNS server 2 fields. http://www.pepwave.com 55 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Cellular Settings 1.1.1.1 Network Selection 3G/2G By default, the MAX router will automatically choose a network to connect to. If you wish to use only certain networks, click the button beside the menu item. This drop-down menu allows restricting cellular to particular band. Click the enable the selection of specific bands. button to Authentication Choose from PAP Only or CHAP Only to use those authentication methods exclusively. Select Auto to automatically choose an authentication method. Data Roaming This checkbox enables data roaming on this particular SIM card. Please check your service provider’s data roaming policy before proceeding. Operator Settings This setting applies to 3G/EDGE/GPRS modems only. It does not apply to EVDO/EVDO Rev. A modems.This allows you to configure the APN settings of your connection. If Auto is selected, the mobile operator should be detected automatically. The connected device will be configured and connection will be made automatically. If there is any difficulty in making connection, you may select Custom to enter your carrier’s APN, Login, Password,and Dial Number settings manually. The correct values can be obtained from your carrier. The default http://www.pepwave.com 56 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual and recommended setting isAuto. APN / Login / Password / SIM PIN When Auto is selected, the information in these fields will be filled automatically.Select Customto customize these parameters. The parameter values are determined by and can be obtained from the ISP. Bandwidth Allowance Monitor Check the box Enable to enable bandwidth usage monitoring on this WAN connection for each billing cycle. When this option is not enabled, bandwidth usage of each month is still being tracked but no action will be taken. Action Start Day Monthly Allowance Ifemail notification is enabled, you will be notified by email when usage hits 75% and 95% of the monthly allowance.If Disconnect when usage hits 100% of monthly allowance is checked, this WAN connection will be disconnected automatically when the usage hits the monthly allowance. It will not resume connection unless this option has been turned off or the usage has been reset when a new billing cycle starts. This option allows you to define which day of the month each billing cycle begins. This field is for defining the maximum bandwidth usage allowed for the WAN connection each month. General Settings Standby State This option allows you to choose whether to remain connected or disconnected when this WAN connection is no longer in the highest priority and has entered the standby state. When Remain connected is chosen, bringing up this WAN connection to active makes it immediately available for use. Idle Disconnect When Internet traffic is not detected within the user-specified timeframe, the modem will automatically disconnect. Once the traffic is resumed by the LAN host, the connection will be reactivated. http://www.pepwave.com 57 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Health Check Settings Heath Check Method Timeout This setting allows you to specify the health check method for the cellular connection. Available options are Disabled, Ping, DNS Lookup, HTTP, and SmartCheck. The default method is DNS Lookup.See Section 9.4 for configuration details. If a health check test cannot be completed within the specified amount of time, the test will be treated as failed. Health Check Interval This is the time interval between each health check test. Health Check Retries This is the number of consecutive check failures before treating a connection as down. Recovery Retries This is the number of responses required after a health check failure before treating a connection as up again. Dynamic DNS Settings This setting specifies the dynamic DNS service provider to be used for the WAN based on supported dynamic DNS service providers: Dynamic DNS Service Provider changeip.com dyndns.org no-ip.org tzo.com DNS-O-Matic Select Disabled to disable this feature.See Section 9.5for configuration details. http://www.pepwave.com 58 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 9.3 Wi-Fi WAN To access Wi-Fi WAN settings, click Network>WAN>Details. Wi-Fi WAN Settings WAN Connection Name Standby State Enter a name to represent this WAN connection. This setting specifies the state of the WAN connection while in standby. The available options are Remain Connected (hot standby) and Disconnect (cold standby). http://www.pepwave.com 59 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Health Check Method This setting allows you to specify the health check method for the WAN connection. The available options are Disabled, Ping, DNS Lookup, and HTTP. The default method is Disabled.See Section 9.4 for configuration details. This setting specifies the dynamic DNS service provider to be used for the WAN based on supported dynamic DNS service providers: Dynamic DNS Settings/Dynamic DNS Service Provider changeip.com dyndns.org no-ip.org tzo.com DNS-O-Matic Select Disabled to disable this feature.See Section 9.5for configuration details. Bandwidth Allowance Monitor This option allows you to enable bandwidth usage monitoring on this WAN connection for each billing cycle. When this is not enabled, bandwidth usage each month is still being tracked, but no action will be taken. MTU This setting specifies the maximum transmission unit.By default, MTU is set to Custom 1440.You may adjust the MTU value by editing the text field. Click Default to restore the default MTU value. Select Auto and the appropriate MTU value will be automatically detected. The auto-detection will run each time the WAN connection establishes Roaming Connect to Any Open Mode AP Reply to ICMP PING Checking this box will enable Wi-Fi roaming. Click the icon for additional options. This option is to specify whether the Wi-Fi WAN will connect to any open mode access point it finds. By default, this is disabled. If this settingis disabled, the WAN connection will not respond to ICMP pingrequests. By default, this setting is enabled. 9.3.1 Creating Wi-Fi Connection Profiles You can manually create a profile to connect to a Wi-Fi connection. This is useful for creating a profile for connecting to hidden-SSID access points. Click Network>WAN>Details>Create Profile…to get started. This will open a window similar to the one shown below: http://www.pepwave.com 60 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Wi-Fi Connection Profile Settings Type Network Name (SSID) Select whether the network will connect automatically or manually. Enter a name to represent this Wi-Fi connection. This option allows you to select which security policy is used for this wireless network. Available options: Open WEP WPA/WPA2 – Personal WPA/WPA2 – Enterprise Security http://www.pepwave.com 61 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 9.4 WAN Health Check To ensure traffic is routed to healthy WAN connections only, the Pepwave routercan periodically check the health of each WAN connection.The health check settings for each WAN connection can be independently configured via Network>WAN>Details. Health Check Settings Method This setting specifies the health check method for the WAN connection. This value can be configured as Disabled, PING, DNS Lookup, or HTTP. The default method is DNS Lookup.For mobile Internet connections, the value of Method can be configured as Disabled or SmartCheck. Health Check Disabled When Disabled is chosen in the Method field, the WAN connection will always be considered as up.The connection will NOTbe treated as down in the event of IP routing errors. Health Check Method: PING ICMP ping packets will be issued to test the connectivity with a configurable target IP address or hostname. A WAN connection is considered as up if ping responses are received from either one or both of the ping hosts. PING Hosts This setting specifies IP addresses or hostnames with which connectivity is to be tested via ICMP ping.If Use first two DNS servers as Ping Hosts is checked, the target ping host will be the first DNS server for the corresponding WAN connection.Reliable ping hosts with a high uptime should be considered.By default, the first two DNS servers of the WAN connection are used as the ping hosts. Health Check Method: DNS Lookup DNS lookups will be issued to test connectivity with target DNS servers. The connection will be treated as up if DNS responses are received from one or both of the servers, regardless of whether the result was positive or negative. Health Check DNS Servers This field allows you to specify two DNS hosts’ IP addresses with which connectivity is to be tested via DNS lookup. If Use first two DNS servers as Health Check DNS Servers is checked,the first two DNS servers will be the DNS lookup targets for checking a connection's health. If the box is not checked, Host 1 must be filled, while a value for Host 2 is optional. If Include public DNS servers is selected and no response is received from all specified DNS servers, DNS lookups will also be issued to some public DNS servers. A WAN connection will be treated as down only if there is also no response received from the public DNS servers. Connections will be considered as up if DNS responses are received from any one of the health check DNS servers, regardless of a positive or negative result.By default, the first two DNS servers of the WAN connection are used as the health check DNS servers. http://www.pepwave.com 62 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Health Check Method: HTTP HTTP connections will be issued to test connectivity with configurable URLs and strings to match. URL1 WAN Settings>WAN Edit>Health Check Settings>URL1 The URL will be retrieved when performing an HTTP health check. When String to Match is left blank, a health check will pass if the HTTP return code is between 200 and 299 (Note: HTTP redirection codes 301 or 302 are treated as failures). When String to Match is filled, a health check will pass if the HTTP return code is between 200 and 299 and if the HTTP response content contains the string. URL 2 WAN Settings>WAN Edit>Health Check Settings>URL2 If URL2 is also provided, a health check will pass if either one of the tests passed. Other Health Check Settings This setting specifies the timeoutin secondsfor ping/DNS lookup requests. The default timeout is 5 seconds. Timeout Health Check Interval This setting specifies the time interval in seconds between ping or DNS lookup requests. The default health check interval is 5 seconds. Health Check Retries This setting specifies the number of consecutive ping/DNS lookup timeouts after which thePepwave routerwill treat the corresponding WAN connection as down. Default health retries is set to 3. Using the default Health Retries setting of 3, the corresponding WAN connection will be treated as down after three consecutive timeouts. Recovery Retries This setting specifies the number of consecutive successful ping/DNS lookup responses that must be received before the Pepwave routertreats a previously down WAN connection as up again. By default, Recover Retriesis set to 3. Using the default setting, a WAN connection that is treated as down will be considered as up again upon receiving three consecutive successful ping/DNS lookup responses. Automatic Public DNS Server Check on DNS Test Failure When the health check method is set to DNS Lookup and health checks fail, the Pepwave routerwill automatically perform DNS lookups on public DNS servers. If the tests are successful, the WAN may not be down, but rather the target DNS server malfunctioned. You will see the following warning message on the main page: http://www.pepwave.com 63 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 9.5 Dynamic DNS Settings Pepwave routers are capable of registering the domain name relationships to dynamic DNS service providers. Through registration with dynamic DNS service provider(s), the default public Internet IP address of each WAN connection can be associated with a host name. With dynamic DNS service enabled for a WAN connection, you can connect to your WAN's IP address from the external, even if its IP address is dynamic. You mustregister for an account from the listed dynamic DNS service providers before enabling this option. If the WAN connection's IP address is a reserved private IP address (i.e., behind a NAT router), the public IP of each WAN will be automatically reported to the DNS service provider. Either upon a change in IP addresses or every 23 days without link reconnection, the Pepwave routerwill connect to the dynamic DNS service provider to perform an IP address update within the provider’s records. The settings for dynamic DNS service provider(s) and the association of hostname(s) are configured via Network>WAN>Details>Dynamic DNS Service Provider/Dynamic DNS Settings. Dynamic DNS Settings This setting specifies the dynamic DNS service provider to be used for the WAN based on supported dynamic DNS service providers: Dynamic DNS Account Name / changeip.com dyndns.org no-ip.org tzo.com DNS-O-Matic Select Disabled to disable this feature. This setting specifies the registered user name for the dynamic DNS service. http://www.pepwave.com 64 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Email Address Password / TZO Key This setting specifies the password for the dynamic DNS service. Hosts / Domain This field allows you to specify a list of host names or domains to be associated with the public Internet IP address of the WAN connection.If you need to enter more than one host, use a carriage return to separate them. Important Note In order to use dynamic DNS services, appropriate host name registration(s) and a valid account with a supported dynamic DNS service provider are required.A dynamic DNS update is performed whenever a WAN’s IP address changes (e.g., the IP is changed after a DHCP IP refresh, reconnection, etc.).Due to dynamic DNS service providers’ policy, a dynamic DNS host will automatically expire if the host record has not been updated for a long time. Therefore the Pepwave routerperforms an update every 23 days, even if a WAN’s IP address has not changed. http://www.pepwave.com 65 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 10 Advanced Wi-Fi Settings Wi-Fi settings can be configured at Advanced>Wi-Fi Settings (or AP>Settings on some models). Note that menus displayed can vary by model. Wi-Fi Radio Settings This drop-down menu specifies the national/regional regulations which the Wi-Fi radio should follow. Operating Country If a North American region is selected, RF channels 1 to 11 will be available and the maximum transmission power will be 26 dBm (400 mW). If European region is selected, RF channels 1 to 13 will be available. The maximum transmission power will be 20 dBm (100 mW). NOTE: Users are required to choose an option suitable to local laws and regulations. Important Note Per FCC regulation, the country selection is not available on all models marketed in the US. All US models are fixed to US channels only. Wi-Fi AP Settings Protocol This option allows you to specify whether 802.11b and/or 802.11g client association requests will be accepted. Available options are 802.11ng and 802.11na. By default, 802.11ng is selected. Channel This option allows you to select which 802.11 RF channel will be utilized.Channel 1 (2.412 GHz) is selected by default. Channel Width Available options are20 MHz, 40 MHz, and Auto (20/40 MHz) . Default is Auto (20/40 MHz), which allows both widths to be used simultaneously. Output Power This option is for specifying the transmission output power for the Wi-Fi AP.There are 4 relative power levels available – Max, High, Mid, and Low. The actual output power will be bound by the regulatory limits of the selected country. http://www.pepwave.com 66 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Advanced Wi-Fi AP settings can be displayed by clicking the on the top right-hand corner of the Wi-Fi AP Settingssection, which can be found at AP>Settings. Other models will display a separate section called Wi-Fi AP Advanced Settings, which can be found at Advanced>Wi-Fi Settings. Wi-Fi AP Advanced Settings Beacon Rate Beacon Interval DTIM This option is for setting the transmit bit rate for sending a beacon. By default, 1Mbps is selected. This field allows you to set the frequency for the beacon to include delivery traffic indication messages. The interval is measured in milliseconds. The default value is set to 1 ms. Slot Time This field is for specifying the unit wait time before transmitting a packet. By default, this field is set to 9 µs. ACK Timeout Frame Aggregation Guard Interval This option is for setting the time interval between each beacon. By default, 100ms is selected. This field is for setting the wait time to receive an acknowledgement packet before performing a retransmission.By default, this field is set to 48 µs. This option allows you to enable frame aggregation to increase transmission throughput. This is where you opt for a short or long guard period interval for your transmissions. - Advanced feature, please click the http://www.pepwave.com button on the top right-hand corner to activate. 67 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Wi-Fi WAN settings can be configured at Advanced>Wi-Fi Settings (or Advanced>Wi-Fi WAN or some models). Wi-Fi WAN Settings Channel Width Available options are20/40 MHz and 20 MHz. Default is 20/40 MHz, which allows both widths to be used simultaneously. Bit Rate This option allows you to select a specific bit rate for data transfer over the device’s WiFi network. By default, Auto is selected. Output Power This option is for specifying the transmission output power for the Wi-Fi AP.There are 4 relative power levels available – Max, High, Mid, and Low. The actual output power will be bound by the regulatory limits of the selected country. Note that selecting the Boost option may cause the MAX’s radio output to exceed local regulatory limits. http://www.pepwave.com 68 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 11 MediaFast Configuration MediaFast settings can be configured from the Network menu. 11.1 Setting Up MediaFast Content Caching To access MediaFast content caching settings, select Advanced>Cache Control. Cache Control Settings Domain Choose to Cache on all domains, or enter domain names and then choose either Cache the specified domains only or Do not cache the specified domains. Content Type Check these boxes to cache the listed content types or leave boxes unchecked to disable caching for the listed types. Cache Lifetime Settings Enter a file extension, such as JPG or DOC. Then enter a lifetime in days to specify how long files with that extension will be cached. Add or delete entries using the controls on the right. http://www.pepwave.com 69 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 11.2 Scheduling Content Prefetching Content prefetching allows you to download content on a schedule that you define, which can help to preserve network bandwidth during busy times and keep costs down. To access MediaFast content prefetching settings, select Advanced>Prefetch Schedule. Prefetch Schedule Settings Name This field displays the name given to the scheduled download. Status Check the status of your scheduled download here. Next Run Time/Last Run Time These fields display the date and time of the next and most recent occurrences of the scheduled download. Last Duration Check this field to ensure that the most recent download took as long as expected to complete. A value that is too low might indicate an incomplete download or incorrectly specified download target, while a value that is too long could mean a download with an incorrectly specified target or stop time. Result Last Download This field indicates whether downloads are in progress ( To edit a scheduled download, click To cancel a scheduled download, click To delete a scheduled download, click New Schedule ). Check this field to ensure that the most recent download file size is within the expected range. A value that is too low might indicate an incomplete download or incorrectly specified download target, while a value that is too long could mean a download with an incorrectly specified target or stop time. This field is also useful for quickly seeing which downloads are consuming the most storage space. To begin a scheduled download immediately, click Actions ) or complete ( To begin creating a new scheduled download, click this button. http://www.pepwave.com 70 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Clear Web Cache Clear Statistics To clear all cached content, click this button. Note that this action cannot be undone. To clear all prefetch and status page statistics, click this button. 11.3 Viewing MediaFast Statistics To get details on storage and bandwidth usage, selectStatus>MediaFast. http://www.pepwave.com 71 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 12 Bandwidth Bonding SpeedFusionTM/ PepVPN Pepwave bandwidth bonding SpeedFusionTMfunctionality securely connectsyourPepwaverouter to anotherPepwave or Peplink device (PeplinkBalance210/310/380/580/710/1350only). Data, voice, or video communications between these locations are kept confidential across the public Internet. Bandwidth bonding SpeedFusionTM is specifically designed for multi-WAN environments. Pepwave routerscan aggregate all WAN connections’ bandwidth for routing SpeedFusionTMtraffic. Unless all the WAN connections of one site are down, Pepwave routerscan keep theVPN up and running. VPN bandwidth bonding is supported in Firmware 5.1 or above. All available bandwidth will be utilized to establish the VPN tunnel, and all traffic will be load balanced at packet level across all links.VPN bandwidth bonding is enabled by default. 12.1 PepVPN The local LAN subnet and subnets behind the LAN (defined under Static Route on the LAN settings page) will be advertised to the VPN. All VPN members (branch offices and headquarters) will be able to route to local subnets. http://www.pepwave.com 72 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Note that all LAN subnets and the subnets behind them must be unique. Otherwise, VPN members will not be able to access each other. All data can be routed over the VPN using the 256-bit AES encryption standard.To configure, navigate to Advanced>SpeedFusion™or Advanced>PepVPNand click the New Profile button to create a new VPN profile(you may have to first save the displayed default profile in order to acesss the New Profile button). Each profile specifiesthe settings for making VPN connection with one remote Pepwave or Peplink device. Note that available settings vary by model. A list of defined SpeedFusionconnection profiles and a Link Failure Detection Time option will be shown. Click the New Profile button to create a new VPN connection profile for making a VPN connection to a remote Peplink Balance via the available WAN connections. Each profile is for making a VPN connection with one remote Peplink Balance. PepVPN Profile Settings Name This field is for specifying a name to represent this profile. The name can be any combination of alphanumeric characters (0-9, A-Z, a-z), underscores (_), dashes (-), and/or non-leading/trailing spaces ( ). Active When this box is checked, this VPN connection profile will be enabled. Otherwise, it will be disabled. Encryption Authentication By default, VPN traffic is encrypted with 256-bit AES. If Off is selected on both sides of a VPN connection, no encryption will be applied. Select from By Remote ID Only, Preshared Key, or X.509 to specify the method the Peplink Balance will use to authenticate peers. When selecting By Remote ID Only, be http://www.pepwave.com 73 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual sure to enter a unique peer ID number in the Remote ID field. This optional field becomes available when Remote ID /Pre-shared Key is selected as the Peplink Balance’s VPN Authentication method, as explained above. Pre-shared Key defines the pre-shared key used for this particular VPN connection. While the Remote ID is mandatory for authentication, the Pre-shared Key is optional; providing an extra layer of security. Remote ID / Pre-shared Key The connection will be up only if the pre-shared keys on each side match. When the peer is running firmware 5.0+, this setting will be ignored. Pre-shared keys can be up to 63 characters in length, Enter Remote IDs either by typing out each Remote ID and Pre-shared Key, or by pasting a CSV. If you wish to paste your credentials from an existing CSV file, click the to the “Remote ID / Preshared Key” setting. Remote ID/Remote Certificate icon next These optional fields become available when X.509 is selected as the Peplink Balance’s VPN authentication method, as explained above. To authenticate VPN connections using X.509 certificates, copy and paste certificate details into these fields. To get more information on a listed X.509 certificate, click the Show Details link below the field. Allow Shared Remote ID When this option is enabled, the router will allow multiple peers to run using the same remote ID. NAT Mode When NAT Mode is enabled, all remote traffic over the VPN will be tagged with the IP address assigned by the DHCP server. This prevents address conflicts when multiple remote sites are on the same LAN subnet. Remote IP Address / Host Names (Optional) If NAT Mode is not enabled, you can enter a remote peer’s WAN IP address or hostname(s) here. If the remote uses more than one address, enter only one of them here. Multiple hostnames are allowed and can be separated by a space character or carriage return. Dynamic-DNS host names are also accepted. This field is optional. With this field filled, the Peplink Balance will initiate connection to each of the remote IP addresses until it succeeds in making a connection. If the field is empty, the Peplink Balance will wait for connection from the remote peer. Therefore, at least one of the two VPN peers must specify this value. Otherwise, VPN connections cannot be established. This field is used to specify a UDP port number for transporting outgoing VPN data. If Default is selected, UDP port 4500 will be used. Port 32015 will be used if the remote unit uses Firmware prior to version 5.4 or if port 4500 is unavailable. Data Port If Custom is selected, enter an outgoing port number from 1 to 65535. This is useful for situations where UDP ports 4500 and 32015 are blocked. Port numbers do not need to be the same on both ends of the VPN tunnel. Bandwidth Limit Define maximum download and upload speed to each individual peer. This functionality requiresthe peer to use PepVPN version 4.0.0 or above. WAN Select the degreeto which WAN Smoothing will be implemented across your WAN links. http://www.pepwave.com 74 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual SmoothingA - Advanced feature, please click the button on the top right-hand corner to activate. To enable Layer 2 Bridging between PepVPN profiles, navigate to Network>LAN>Basic Settings>*LAN Profile Name* and refer to instructions in section8.1 WAN Connection Priority WAN Connection Priority If your device supports it, you can specify the priority of WAN connections to be used for making VPN connections. WAN connections set to OFF will never be used. Only available WAN connections with the highest priority will be used. To enable asymmetric connections, connection mapping to remote WANs, cut-off latency, and packet loss suspension time, click the button. Send All Traffic To This feature allows you to redirect all traffic to a specified PepVPN connection. Click the connection and the following menu will appear: button to select your You could also specify a DNS server to resolve incoming DNS requests. Outbound Policy/PepVPN Outbound Custom Rules Some models allow you to set outbound policy and custom outbound rules from Advanced>PepVPN. See Section 14 for more information on outbound policy settings. http://www.pepwave.com 75 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual PepVPN Local ID The local ID is a text string (254 characters maximum length) to identify this local unit when establishing a VPN connection. When creating a profile on a remote unit, this local ID must be entered in the remote unit's Remote ID field. Click the icon to edit Local ID. PepVPN Settings 1.1.1.3 1.1.1.2 Handshake PortA Link Failure Detection Time - Advanced feature, please click the http://www.pepwave.com To designate a custom handshake port (TCP), click the custom radio button and enter the port number you wish to designate. The bonded VPN can detect routing failures on the path between two sites over each WAN connection. Failed WAN connections will not be used to route VPN traffic. Health check packets are sent to the remote unit to detect any failure. The more frequently checks are sent, the shorter the detection time, although more bandwidth will be consumed. When Recommended (default) is selected, a health check packet is sent every five seconds, and the expected detection time is 15 seconds. When Fast is selected, a health check packet is sent every three seconds, and the expected detection time is six seconds. When Faster is selected, a health check packet is sent every second, and the expected detection time is two seconds. When Extreme is selected, a health check packet is sent every 0.1 second, and the expected detection time is less than one second. button on the top right-hand corner to activate. 76 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Important Note Peplink proprietary SpeedFusionTM uses TCP port 32015 and UDP port 4500 for establishing VPN connections. If you have a firewall in front of your Pepwave devices, you will need to add firewall rules for these ports and protocols to allow inbound and outbound traffic to pass through the firewall. Tip Want to know more about VPN sub-second session failover? Visit our YouTube Channel for a video tutorial! http://youtu.be/TLQgdpPSY88 http://www.pepwave.com 77 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 12.2 The Pepwave Router Behind a NAT Router Pepwave routerssupport establishing SpeedFusionTM over WAN connections which are behind a NAT (network address translation) router. To enable a WAN connection behind a NAT router to accept VPN connections, you can configure the NAT router in front of the WAN connection to inbound port-forward TCP port 32015 to the Pepwave router. If one or more WAN connections onUnit A can accept VPN connections (by means of port forwarding or not), while none of the WAN connections on the peer Unit B can do so, you should enter all of Unit A’s public IP addresses or hostnames into Unit B’sRemote IP Addresses / Host Namesfield. Leave the field in Unit A blank. With this setting, a SpeedFusionTMconnection can be set up and all WAN connections on both sides will be utilized. See the following diagram for an example of this setup in use: One of the WANs connected to RouterA is non-NAT’d (212.1.1.1). The rest of the WANs connected to RouterA and all WANs connected to RouterB are NAT’d. In this case, the Peer IP Addresses / Host Names field for RouterB should be filled with all of RouterA’s hostnames or public IP addresses (i.e., 212.1.1.1, 212.2.2.2, and 212.3.3.3), and the field in RouterA can be left blank. The two NAT routers on WAN1 and WAN3 connected to Router A should inbound port-forward TCP port 32015 to Router A so that all WANs will be utilized in establishing the VPN. http://www.pepwave.com 78 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 12.3 SpeedFusionTM Status SpeedFusionTMstatus is shown in the Dashboard. The connection status of each connection profile is shown as below. If a remote IP address has not been specified, the status will be displayed as “Starting”. In this state, it will simply wait for an incoming connection and will consume no resources. After clicking theStatus button at the top right corner of the SpeedFusionTM table, you will be forwarded to Status>SpeedFusionTM, where you can view subnet and WAN connection information for each VPN peer. Please refer to Section22.6for details. IP Subnets Must Be Unique Among VPN Peers The entire interconnected SpeedFusionTM network is a single non-NAT IP network. Avoid duplicating subnets in your sites to prevent connectivity problems when accessing those subnets. http://www.pepwave.com 79 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 13 IPsec VPN IPsec VPN functionality securely connects one or more branch offices to your company's main headquarters or to other branches. Data, voice, and video communications between these locations are kept safe and confidential across the public Internet. IPsecVPN on Pepwave routersis specially designed for multi-WAN environments. For instance, if a user sets up multiple IPsec profiles for a multi-WAN environment and WAN1 is connected and healthy, IPsec traffic will go through this link. However, should unforeseen problems (e.g.,unplugged cables or ISP problems) cause WAN1 to go down, our IPsec implementation will make use of WAN2 and WAN3 for failover. 13.1 IPsec VPN Settings ManyPepwaveproducts can makemultiple IPsec VPN connections with Peplink, Pepwave, Cisco,andJuniper routers.Note that all LAN subnets and the subnets behind them must be unique. Otherwise, VPN members will not be able to access each other.All data can be routed over the VPN with a selection of encryption standards, such as 3DES, AES-128, and AES-256.To configure IPsec VPN on Pepwave devices that support it, navigate to Advanced>IPsec VPN. A NAT-Traversal option and list of definedIPsec VPNprofiles will be shown. NATTraversalshould be enabled if your system is behind a NAT router.Click the New Profile button to create new IPsec VPN profiles that make VPN connections to remote Pepwave, Cisco, or Juniper routers via available WAN connections. To edit any of the profiles, click on its associated connection name in the leftmost column. http://www.pepwave.com 80 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual IPsec VPN Settings Name This field is for specifying a local name to represent this connection profile. Active When this box is checked, this IPsec VPN connection profile will be enabled. Otherwise, it will be disabled. Connect Upon Disconnection of Check this box and select a WAN to connect to this VPN automatically when the specified WAN is disconnected. Remote Gateway IP Address / Host Name Enter the remote peer’s public IP address.For Aggressive Mode, this is optional. Local Networks Enter the local LAN subnets here. If you have defined static routes, they will be shown here. Remote Networks Enter the LAN and subnets that are located at the remote site here. http://www.pepwave.com 81 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Authentication Mode Force UDP Encapsulation To access your VPN, clients will need to authenticate by your choice of methods. Choose between the Preshared Key and X.509 Certificate methods of authentication. Choose Main Mode if both IPsec peers use static IP addresses.Choose Aggressive Mode if one of the IPsec peers uses dynamic IP addresses. For forced UDP encapsulation regardless of NAT-traversal, tick this checkbox. Pre-shared Key This defines the peer authentication pre-shared key used to authenticate this VPN connection. The connection will be up only if the pre-shared keys on each side match. Remote Certificate (pem encoded) Available only when X.509 Certificate is chosen as the Authentication method, this field allows you to paste a valid X.509 certificate. Local ID In Main Mode, this field can be left blank. In Aggressive Mode, if Remote Gateway IP Addressis filled on this end and the peer end, this field can be left blank. Otherwise, this field is typically a U-FQDN. Remote ID In Main Mode, this field can be left blank. In Aggressive Mode, if Remote Gateway IP Addressis filled on this end and the peer end, this field can be left blank. Otherwise, this field is typically a U-FQDN. Phase 1 (IKE) Proposal In Main Mode, this allows setting up to six encryption standards, in descending order of priority, to be used in initial connection key negotiations. In Aggressive Mode, only one selection is permitted. Phase 1 DH Group This is the Diffie-Hellman group used within IKE. This allows two parties to establish a shared secret over an insecure communications channel. The larger the group number, the higher the security. Group 2:1024-bit is the default value. Group 5:1536-bit is the alternative option. Phase 1 SA Lifetime This setting specifies the lifetime limit of this Phase 1 Security Association. By default, it is set at 3600 seconds. Phase 2 (ESP) Proposal In Main Mode, this allows setting up to six encryption standards, in descending order of priority, to be used for the IP data that is being transferred. In Aggressive Mode, only one selection is permitted. Phase 2 PFS Group Perfect forward secrecy (PFS) ensures that if a key was compromised, the attacker will be able to access only the data protected by that key. None - Do not request for PFS when initiating connection. However, since there is no valid reason to refuse PFS, the system will allow the connection to use PFS if requested by the remote peer. This is the default value. Group 2: 1024-bit Diffie-Hellman group. The larger the group number, the higher the security. Group 5:1536-bit is the third option. Phase 2 SA Lifetime This setting specifies the lifetime limit of this Phase 2 Security Association. By default, it is set at 28800 seconds. http://www.pepwave.com 82 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual WAN Connection Priority WAN Connection Select the appropriate WAN connection from the drop-down menu. http://www.pepwave.com 83 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 14 Outbound Policy Management Pepwave routerscan flexibly manage and load balance outbound traffic among WAN connections. Important Note Outbound policy is applied only when more than one WAN connection is active. The settings for managing and load balancing outbound traffic are located at Advanced>Outbound Policy or Advanced>PepVPN, depending on model. Outbound policies for managing and load balancing outbound traffic are located at Network>Outbound Policy> or Advanced>PepVPN>Outbound Policy. 14.1 Outbound Policy There are three main selections for the outbound traffic policy: High Application Compatibility Normal Application Compatibility Custom Note that some Pepwave routers provide only the Send All Traffic To setting here. See Section 12.1 for details. Outbound Policy Settings High Outbound traffic from a source LAN device is routed through the same WAN connection regardless of the destination Internet IP address and protocol. This option provides the http://www.pepwave.com 84 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Application Compatibility highest application compatibility. Normal Application Compatibility Outbound traffic from a source LAN device to the same destination Internet IP address will be routed through the same WAN connection persistently, regardless of protocol. This option provides high compatibility to most applications, and users still benefit from WAN link load balancing when multiple Internet servers are accessed. Custom Outbound traffic behavior can be managed by defining rules in a custom rule table. A default rule can be defined for connections that cannot be matched with any of the rules. The default policy is Normal Application Compatibility. Tip Want to know more about creating outbound rules? Visit our YouTube Channel for a video tutorial! http://youtu.be/rKH4AS_bQnE 14.2 Custom Rulesfor Outbound Policy Click in the Outbound Policy form.Choose Custom and press the Savebutton. http://www.pepwave.com 85 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual The bottom-most rule is Default. Edit this rule to change the device’s default manner of controlling outbound traffic for all connections that do not match any of the rules above it. Under the Service heading, clickDefaultto change these settings. To rearrange the priority of outbound rules, drag and drop them into the desired sequence. By default, Auto is selected as the Default Rule.You can select Custom to change the algorithm to be used. Please refer to the upcoming sections for the details on the available algorithms. To create a custom rule, click Add Rule at the bottom of the table. Note that some http://www.pepwave.com 86 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Pepwave routers display this button at Advanced>PepVPN>PepVPN Outbound Custom Rules. New Custom Rule Settings Service Name This setting specifies the name of the outbound traffic rule. Enable This setting specifies whether the outbound traffic rule takes effect. When Enable is checked, the rule takes effect: traffic is matched and actions are takenby the Pepwave routerbased on the other parameters of the rule. WhenEnableis unchecked, the rule does not take effect: the Pepwave routerdisregards the other parameters of the rule. Source This setting specifies the source IP address, IP network, or MAC address for traffic that matches the rule. This setting specifies the destination IP address, IP network, or domain name for traffic that matches the rule. Destination Protocol and Port If Domain Name is chosen and a domain name, such as foobar.com, is entered, any outgoing accesses to foobar.com and *.foobar.com will match this criterion. You may enter a wildcard (.*) at the end of a domain name to match any host with a name having the domain name in the middle. If you enter foobar.*, for example, www.foobar.com, www.foobar.co.jp, or foobar.co.uk will also match. Placing wildcards in any other position is not supported. NOTE: if a server has one Internet IP address and multiple server names, and if one of the names is defined here, accesses to any one of the server names will also match this rule. This setting specifies the IP protocol and port of traffic that matches this rule. http://www.pepwave.com 87 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual This setting specifies the behavior of the Pepwave routerfor the custom rule. One of the following values can be selected (note that some Pepwave routers provide only some of these options): Algorithm Weighted Balance Persistence Enforced Priority Overflow Least Used Lowest Latency The upcoming sections detail the listed algorithms. Terminate Sessions on Link Recovery This setting specifies whether to terminate existing IP sessions on a less preferred WAN connection in the event that a more preferred WAN connection is recovered. This setting is applicable to the Weighted,Persistence, and Priority algorithms.By default, this setting is disabled. In this case, existing IP sessions will not be terminated or affected when any other WAN connection is recovered. When this setting is enabled, existing IP sessions may be terminated when another WAN connection is recovered, such that only the preferred healthy WAN connection(s) is used at any point in time. http://www.pepwave.com 88 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 14.2.1 Algorithm: Weighted Balance This setting specifies the ratio of WAN connection usage to be applied on the specified IP protocol andport. This setting is applicable only when Algorithm is set to Weighted Balance. The amount of matching traffic that is distributed to a WAN connection is proportional to the weight of the WAN connection relative to the total weight.Use the sliders to change each WAN’s weight. For example, with the following weight settings: Ethernet WAN1: 10 Ethernet WAN2: 10 Wi-Fi WAN: 10 Cellular 1: 10 Cellular 2: 10 USB: 10 Total weight is 60 = (10 +10 + 10 + 10 + 10 + 10). Matching traffic distributed to Ethernet WAN1 is 16.7% = (10 / 60 x 100%. Matching traffic distributed to Ethernet WAN2 is 16.7% = (10 / 60) x 100%. Matching traffic distributed to Wi-Fi WAN is 16.7% = (10 / 60) x 100%. Matching traffic distributed to Cellular 1 is 16.7% = (10 / 60) x 100%. Matching traffic distributed to Cellular 2 is 16.7% = (10 / 60) x 100%. Matching traffic distributed to USB is 16.7% = (10 / 60) x 100%. http://www.pepwave.com 89 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 14.2.2 Algorithm: Persistence The configuration of persistent services is the solution to the few situations where link load distribution for Internet services is undesirable. For example, for security reasons, many e-banking and other secure websitesterminate the session when the client computer’s Internet IP address changes mid-session. In general, different Internet IP addresses represent different computers. The security concern is that an IP address change during a session may be the result of an unauthorized intrusion attempt. Therefore, to prevent damages from the potential intrusion, the session is terminated upon the detection of an IP address change. Pepwaverouterscan be configured to distribute data traffic across multiple WAN connections. Also, the Internet IP depends on the WAN connections over which communication actually takes place. As a result, a LAN client computer behind the Pepwaveroutermay communicate using multiple Internet IP addresses. For example, a LAN client computer behind a Pepwave routerwith three WAN connections may communicate on the Internet using three different IP addresses. With the persistence feature, rules can be configured to enable client computers to persistently utilize the same WAN connections for e-banking and other secure websites. As a result, a client computer will communicate using one IP address, eliminating the issues mentioned above. There are two persistent modes: By Sourceand By Destination. By Source: By Destination: The same WAN connection will be used for traffic matching the rule and originating from the same machine, regardless of its destination. This option will provide the highest level of application compatibility. The same WAN connection will be used for traffic matching the rule, originating from the same machine, and going to the same destination. This option can better distribute loads to WAN connections when there are only a few client machines. The default mode is By Source.When there are multiple client requests, they can be distributed (persistently) to WAN connections with a weight. If you choose AutoinLoad Distribution, the weights will be automatically adjusted according to each WAN’s Downstream Bandwidth which is specified in the WAN settings page). If you choose Custom, you can customize the weight of each WAN manually by using the sliders. http://www.pepwave.com 90 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 14.2.3 Algorithm: Enforced This setting specifies the WAN connection usage to be applied on the specified IP protocol and port. This setting is applicable only whenAlgorithm is set toEnforced. Matching traffic will be routed through the specified WAN connection, regardless of the health check status of the WAN connection.Starting from Firmware 5.2, outbound traffic can be enforced to go through a specified SpeedFusionTM connection. 14.2.4 Algorithm: Priority This setting specifies the priority of the WAN connections used to route the specified network service. The highest priority WAN connection available will always be used for routing the specified type of traffic. A lower priority WAN connection will be used only when all higher priority connections have become unavailable. Starting from Firmware 5.2, outbound traffic can be prioritized to go through SpeedFusionTM connection(s). By default, VPN connections are not included in the priority list. Tip Configure multiple distribution rules to accommodate different kinds of services. 14.2.5 Algorithm: Overflow The traffic matching this rule will be routed through the healthy WAN connection that has the highest priority and is not in full load. When this connection gets saturated, new sessions will be routed to the next healthy WAN connection that is not in full load. http://www.pepwave.com 91 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Drag and drop to specify the order of WAN connections to be used for routing traffic. Only the highest priority healthy connection that is not in full load will be used. 14.2.6 Algorithm: Least Used The traffic matching this rule will be routed through the healthy WAN connection that is selected in Connectionand has the most available download bandwidth. The available download bandwidth of a WAN connection is calculated from the total download bandwidth specified on the WAN settings page and the current download usage. The available bandwidth and WAN selection is determined every time an IP session is made. 14.2.7 Algorithm: Lowest Latency The traffic matching this rule will be routed through the healthy WAN connection that is selected in Connection and has the lowest latency. Latency checking packets are issued periodically to a nearby router of each WAN connection to determine its latency value. The latency of a WAN is the packet round trip time of the WAN connection. Additional network usage may be incurred as a result. Tip The roundtrip time of a 6M down/640k uplinkcan be higher than that of a 2M down/2M up linkbecause the overall round trip time is lengthened by its slowerupload bandwidth, despite its higher downlink speed.Therefore, this algorithm isgood for two scenarios: All WAN connections are symmetric; or A latency sensitive application must be routed through the lowestlatency WAN, regardless of the WAN’s http://www.pepwave.com 92 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual available bandwidth. 14.2.8 Expert Mode Expert Mode is available on some Pepwave routers for use by advanced users. To enable the feature, click on the help icon and click turn on Expert Mode. In Expert Mode, a new special rule, SpeedFusionTM Routes, is displayed in the Custom Rules table. This rule represents all SpeedFusionTM routes learned from remote VPN peers. By default, this bar is on the top of all custom rules. This position means that traffic for remote VPN subnets will be routed to the corresponding VPN peer. You can create custom Priority or Enforced rules and move them above the bar to override the SpeedFusionTM routes. Upon disabling Expert Mode, all rules above the bar will be removed. http://www.pepwave.com 93 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 15 Inbound Access 15.1 Port Forwarding Service Pepwave routers can act as a firewall that blocks, by default, all inbound access from the Internet. By using port forwarding, Internet users can access servers behind the Pepwave router.Inbound port forwarding rules can bedefined at Advanced>Port Forwarding. To define a new service, click Add Service. Port Forwarding Settings Enable This setting specifies whether the inbound service takes effect. When Enable is checked, the inbound service takes effect: traffic is matched and actions are taken by the Pepwave routerbased on the other parameters of the rule. When this setting is disabled, the inbound service does not take effect: the Pepwave routerdisregards the other parameters of the rule. Service Name This setting identifies the service to the system administrator.Valid values for this setting consist of only alphanumeric and underscore “_” characters. IP Protocol The IP Protocol setting, along with the Port setting, specifies the protocol of the service as TCP, UDP, ICMP, or IP.Traffic that is received by the Pepwave routervia the specified protocol at the specified port(s) is forwarded to the LAN hosts specified by the Servers setting. Please see below for details on the Port and Servers settings.Alternatively, the Protocol Selection Tool drop-down menu can be used to automatically fill in the protocol and a single port number of common Internet services (e.g. HTTP, HTTPS, etc.). After selecting an item from the Protocol Selection Tool drop-down menu, the protocol and port number remain manually modifiable. http://www.pepwave.com 94 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual The Port setting specifies the port(s) that correspond to the service, and can be configured to behave in one of the following manners: Any Port, Single Port, Port Range,Port Map,and Range Mapping Any Port: all traffic that is received by the Pepwave routervia the specified protocol is forwarded to the servers specified by the Servers setting. For example, with IP Protocol set to TCP, and Port set to Any Port, all TCP traffic is forwarded to the configured servers. Single Port: traffic that is received by the Pepwave routervia the specified protocol at the specified port is forwarded via the same port to the servers specified by the Servers setting. For example, with IP Protocol set to TCP, and Port set to Single Port and Service Port 80, TCP traffic received on port 80 is forwarded to the configured servers via port 80. Port Port Range: traffic that is received by the Pepwave routervia the specified protocol at the specified port range is forwarded via the same respective ports to the LAN hosts specified by the Servers setting. For example, with IP Protocol set to TCP, and Port set to Port Range and Service Ports 80-88, TCP traffic received on ports 80 through 88 is forwarded to the configured servers via the respective ports. Port Mapping: traffic that is received by Pepwave routervia the specified protocol at the specified port is forwarded via a different port to the servers specified by the Servers setting. For example, with IP Protocol set to TCP, and Port set to Port Mapping, Service Port 80, and Map to Port 88, TCP traffic on port 80 is forwarded to the configured servers via port 88. (Please see below for details on the Servers setting.) Range Mapping: traffic that is received by the Pepwave router via the specified protocol at the specified port range is forwarded via a different port to the servers specified by the Servers setting. Inbound IP Address(es) Server IP Address This setting specifies the WAN connections and Internet IP address(es) from which the service can be accessed. This setting specifies the LAN IP address of the server that handles the requests for the service. http://www.pepwave.com 95 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 15.1.1 UPnP / NAT-PMP Settings UPnP and NAT-PMP are network protocols which allow a computer connected to the LAN port to automatically configure the router to allow parties on the WAN port to connect to itself. That way, the process of inbound port forwarding becomes automated. When a computer creates a rule using these protocols, the specified TCP/UDP port of all WAN connections' default IP address will be forwarded. Check the corresponding box(es) to enable UPnP and/or NAT-PMP. Enable these features only if you trust the computers connected to the LAN ports. When the options are enabled, a table listing all the forwarded ports under these two protocols can be found at Status>UPnP / NAT-PMP. http://www.pepwave.com 96 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 16 NAT Mappings NAT mappingsallow IP address mapping of all inbound and outbound NAT’dtraffic to and from an internal client IP address. Settings to configure NAT mappingsare located at Advanced>NAT Mappings. To add a rule for NAT mappings, click Add NAT Rule. NAT Mapping Settings LAN Client(s) NAT mapping rules can be defined for a single LAN IP Address, an IP Range, or an IP Network. Address This refers to the LAN host’s private IP address.The system maps this address to a number of public IP addresses (specified below) in order to facilitate inbound and outbound traffic.This option is only available when IP Address is selected. Range The IP range is a contiguous group of private IP addresses used by the LAN host. The system maps these addresses to a number of public IP addresses (specified below) to facilitate outbound traffic.This option is only available when IP Range is selected. Network The IP network refers to all private IP addresses and ranges managed by the LAN host. The system maps these addresses to a number of public IP addresses (specified below) to facilitate outbound traffic.This option is only available when IP Network is selected. http://www.pepwave.com 97 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Inbound Mappings This setting specifies the WAN connections and corresponding WAN-specific Internet IP addresses on which the system should bind. Any access to the specified WAN connection(s) and IP address(es) will be forwarded to the LAN host.This option is only available when IP Address is selected in the LAN Client(s) field. Note that inbound mapping is not needed for WAN connections in drop-in mode or IP forwarding mode. Also note that each WAN IP address can be associated to one NAT mapping only. Outbound Mappings This setting specifies the WAN IP addresses that should be used whenanIP connection is made from a LAN host to the Internet.Each LAN host in an IP range or IP network will be evenly mapped to one of each selected WAN's IP addresses (for better IP address utilization) in a persistent manner (for better application compatibility). Note that if you do not want to use a specific WAN for outgoing accesses, you should still choose default here, then customize the outbound access rule in the Outbound Policy section. Also note that WAN connections in drop-in mode or IP forwarding mode are not shown here. Click Save to save the settings when configuration has been completed. Important Note Inbound firewall rules override the Inbound Mappingssettings. http://www.pepwave.com 98 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 17 QoS 17.1 User Groups LAN and PPTP clients can be categorized into three user groups:Manager, Staff, and Guest.This menu allows you to define rules and assign client IP addresses or subnets to a user group. You can apply different bandwidth and traffic prioritization policies on each user group in the Bandwidth Control and Application sections (note that the options available here vary by model). The table is automatically sorted by rule precedence. The smaller and more specific subnets are put towards the top of the table and have higher precedence; larger and less specific subnets are placed towards the bottom. Click the Add button to define clients and their user group. Click the button to remove the defined rule.Two default rules are pre-defined and put at the bottom.They are All DHCP reservation clients and Everyone, and they cannot be removed. The All DHCP reservation client representsthe LAN clients defined in the DHCP Reservation table on the LAN settings page. Everyone represents all clients that are not defined in any rule above. Click on a rule to change its group. Add / Edit User Group Subnet / IP Address Group From the drop-down menu, choose whether you are going to define the client(s) by an IP Address or a Subnet. If IP Address is selected, enter a name defined in DHCP reservation table or a LAN client's IP address. If Subnet is selected, enter a subnet address and specify its subnet mask. This field is to define which User Group the specified subnet / IP address belongs to. Once users have been assigned to a user group, their internet traffic will be restricted by rules defined for that particular group. Please refer to the following two sections for details. http://www.pepwave.com 99 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 17.2 Bandwidth Control You can define a maximum download speed (over all WAN connections) and upload speed (for each WAN connection) that each individual Staff and Guest member can consume. No limit can be imposed on individual Manager members.By default, download and upload bandwidth limits are set to unlimited (set as 0). 17.3 Application 17.3.1 Application Prioritization On many Pepwave routers, you can choose whether to apply the same prioritization settings to all user groups or customize the settings for each group. Three application priority levels can be set: ↑High,━ Normal, and↓Low.Pepwave routers can detectvarious application traffic types by inspecting the packet content. Select an application by choosing a supported application, or by defining a custom application manually. The priority preference of supported applications is placed at the top of the table. Custom applications are at the bottom. http://www.pepwave.com 100 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 17.3.2 Prioritization for Custom Applications Click the Add button to define a custom application. Click the button column to delete the custom application in the corresponding row. in the Action When Supported Applications is selected, the Pepwave routerwill inspect network traffic and prioritize the selected applications. Alternatively, you can select Custom Applicationsand define the application by providing the protocol, scope, port number, and DSCP value. 17.3.3 DSL/Cable Optimization DSL/cable-based WAN connections have lower upload bandwidth and higher download bandwidth. When a DSL/cable circuit's uplink is congested, the download bandwidth will be affected. Users will not be able to download data at full speed until the uplink becomes less congested.DSL/Cable Optimization can relieve such an issue. When it is enabled, the download speed will become less affected by the upload traffic.By default, this feature is enabled. http://www.pepwave.com 101 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 18 Firewall A firewall is a mechanism that selectively filters data traffic between the WAN side (the Internet) and the LAN side of the network. It can protect the local network from potential hacker attacks, access to offensive websites, and/or other inappropriate uses. The firewall functionality of Pepwave routerssupports the selective filtering of data traffic in both directions: Outbound (LAN to WAN) Inbound (WAN to LAN) The firewall also supports the following functionality: Intrusion detection and DoS prevention Web blocking With SpeedFusionTM enabled, the firewall rules also apply to VPN tunneled traffic. 18.1 Outbound and Inbound Firewall Rules 18.1.1 Access Rules The outbound firewall settings are located atAdvanced>Firewall>Access Rules>Outbound Firewall Rules. http://www.pepwave.com 102 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual ClickAdd Ruleto display thefollowing screen: Inbound firewall settings are located atAdvanced>Firewall>Access Rules>Inbound Firewall Rules. Click Add Ruleto display the following screen: Rules are matched from top to bottom.If a connection matches any one of the upper rules, the matching process will stop. If none of the rules match, the Defaultrule will be applied.By default, theDefault rule is set as Allow for both outbound and inbound access. http://www.pepwave.com 103 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Inbound / Outbound Firewall Settings Rule Name Enable WAN Connection (Inbound) This setting specifies a name for the firewall rule. This setting specifies whether the firewall rule should take effect.If the box is checked, the firewall rule takes effect. If the traffic matches the specified protocol/IP/port, actions will be taken by the Pepwave routerbased on the other parameters of the rule.If the box is not checked, the firewall rule does not take effect. The Pepwave routerwill disregard the other parameters of the rule. Select the WAN connection that this firewall rule should apply to. This setting specifies the protocol to be matched.Via a drop-down menu, the following protocols can be specified: TCP Protocol UDP ICMP IP Alternatively, the Protocol Selection Tool drop-down menu can be used to automatically fill in the protocol and port number of common Internet services (e.g., HTTP, HTTPS, etc.) After selecting an item from the Protocol Selection Tool drop-down menu, the protocol and port number remains manually modifiable. This specifies the source IP address(es) and port number(s) to be matched for the firewall rule.A single address, or a network, can be specified as the Source IP & Port setting, as indicated by the following screenshot: Source IP & Port In addition, a single port, or a range of ports, can be specified for the Source IP & Port settings. Destination IP & Port This specifies the destination IP address(es) and port number(s) to be matched for the firewall rule.A single address, or a network, can be specified as the Destination IP & Port setting, as indicated by the following screenshot: In addition, a single port, or a range of ports, can be specified for the Destination IP & Port settings. This setting specifies the action to be taken by the router upon encountering traffic that matches the both of the following: Action Source IP &port Destination IP &port With the value of Allow for the Action setting, the matching traffic passes through the router (to be routed to the destination).If the value of the Action setting is set to Deny, the matching traffic does not pass through the router (and is discarded). Event Logging This setting specifies whether or not to log matched firewall events. The logged messages are shown on the page Status>Event Log.A sample message is as follows: http://www.pepwave.com 104 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Aug 13 23:47:44 Denied CONN=Ethernet WAN SRC=20.3.2.1 DST=192.168.1.20 LEN=48 PROTO=TCP SPT=2260 DPT=80 CONN: The connection where the log entry refers to SRC: Source IP address DST: Destination IP address LEN: Packet length PROTO: Protocol SPT: Source port DPT: Destination port ClickSaveto store your changes. To create an additional firewall rule, click Add Ruleand repeat the above steps. To change a rule’s priority, simply drag and drop the rule: Hold the left mouse button on the rule. Move it to the desired position. Drop it by releasing the mouse button. Tip If the default inbound rule is set to Allow for NAT-enabled WANs, no inbound Allow firewall rules will be required for inbound port forwarding and inbound NAT mapping rules. However, if the default inbound rule is set as Deny, a corresponding Allow firewall rule will be required. http://www.pepwave.com 105 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 18.1.2 Apply Firewall Rules to PepVpn Traffic When this option is enabled, Outbound Firewall Rules will be applied to PepVPN traffic.To turn on this feature, click , check the Enable check box,and press the Save button. 18.1.3 Intrusion Detection and DoS Prevention Pepwave routerscan detect and prevent intrusions and denial-of-service (DoS) attacks from the Internet. To turn on this feature, click , check the Enablecheck box,and press the Savebutton. When this feature is enabled, the Pepwave routerwill detect and prevent the following kinds of intrusions and denial-of-service attacks. Port scan o NMAP FIN/URG/PSH o Xmas tree o Another Xmas tree o Null scan o SYN/RST o SYN/FIN SYN flood prevention Ping flood attack prevention http://www.pepwave.com 106 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 18.2 Web Blocking 18.2.1 Web Blocking Enter an appropriate website address, and the Pepwave router will block and disallow LAN/PPTP/SpeedFusionTM peer clients to access these websites. Exceptions can be added using the instructions in Sections18.2.2 and18.2.3. You may enter awildcard ".*" at the end of a domain name to block any web site with a host name having the domain name in the middle. For example, If you enter foobar.*, www.foobar.com, www.foobar.co.jp, andfoobar.co.uk will be blocked.Placing the wildcard in any other position is not supported.The Pepwave routerwill inspect and look for blocked domain names on all HTTP traffic. Secure web (HTTPS) traffic is not supported. 18.2.2 Exempted User Groups Check and select pre-defined user group(s) who can be exempted from the access blocking rules. User groups can be defined at QoS>User Groups section. Please refer to Section 17.1 for details. 18.2.3 Exempted Subnets With the subnet defined in the field, clients on the particular subnet(s) can be exempted from the access blocking rules. http://www.pepwave.com 107 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 19 Miscellaneous Settings The miscellaneous settings include configuration for high availability, PPTP server, service forwarding, and service passthrough. 19.1 High Availability Many Pepwave routers support high availability (HA) configurations via an open standard virtual router redundancy protocol (VRRP, RFC 3768).In an HA configuration, two Pepwave routers provide redundancy and failover in a master-slave arrangement. In the event that the master unit is down, the slave unit becomes active.High availability will be disabled automatically where there is a drop-in connection configured on a LAN bypass port. In the diagram, the WAN ports of each Pepwave router connect to the router and to the modem. Both Pepwave routers connect to the same LAN switch via a LAN port. An elaboration on the technical details of the implementationof the virtual router redundancy protocol (VRRP, RFC 3768) by Pepwave routers follows: In an HA configuration, the two Pepwave routers communicate with each other using VRRP over the LAN. The two Pepwave routers broadcast heartbeat signals to the LAN at a frequency of one heartbeat signal per second. In the event that no heartbeat signal from the master Pepwave router is received in 3 seconds (or longer) since the last heartbeat signal, the slave Pepwave router becomes active. The slave Pepwave router initiates the WAN connections and binds to a previously configured LAN IP address. At a subsequent point when the master Pepwave router recovers, it will once again become active. http://www.pepwave.com 108 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual You can configure high availability at Advanced>Misc. Settings>High Availability. Interface for Master Router Interface for Slave Router High Availability Enable Checking this box specifies that the Pepwave router is part of a high availability configuration. Group Number This number identifies a pair of Pepwave routers operating in a high availability configuration.The two Pepwave routers in the pair must have the same Group Number value. Preferred Role This setting specifies whether the Pepwave router operates in master or slave mode.Click the corresponding radio button to set the role of the unit. One of the units in the pair must be configured as the master, and the other unit must be configured as the slave. Resume Master Role Upon Recovery This option is displayed when Master mode is selected in Preferred Role.If this option is enabled, once the device has recovered from an outage, it will take over and resume its Master role from the slave unit. Configuration Sync. This option is displayed when Slave mode is selected in Preferred Role.If this option is enabled and the Master Serial Number entered matches with the actual master unit's, the master unit will automatically transfer the configuration to this unit. Please make sure the LAN IP Address and the Subnet Mask fields are set correctly in the LAN settings page.You can refer to the Event Log for the configuration synchronization status. Master Serial Number If Configuration Sync. is checked, the serial number of the master unit is required here for the feature to work properly. Virtual IP The HA pair must share the same Virtual IP. TheVirtual IP and the LAN Administration IP must be under the same network. LAN Administration IP Subnet Mask This setting specifies a LAN IP address to be used for accessing administration functionality.This address should be unique within the LAN. This setting specifies the subnet mask of the LAN. http://www.pepwave.com 109 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Important Note For Pepwave routers in NAT mode, the virtual IP (VIP) should be set as the default gateway for all hosts on the LAN segment. For example, a firewall sitting behind the Pepwave router should set its default gateway as the virtual IP instead of the IP of the master router. In drop-in mode, no other configuration needs to be set. Please note that the drop-in WAN cannot be configured as a LAN bypass port while it is configured for high availability. http://www.pepwave.com 110 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 19.2 PPTP Server Pepwave routersfeature a built-in PPTP server, which enables remote computers to conveniently and securely access the local network.PPTP server settingsare located at Advanced>Misc. Settings>PPTP Server. Check the box to enable PPTP server functionality. All connected PPTP sessions are displayed at Status>Client List. Please refer to Section22.3 for details. Note that available options vary by model. http://www.pepwave.com 111 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual http://www.pepwave.com 112 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual PPTP Server Settings Listen On This setting is for specifying the WAN connection(s) and IP address(es) that the PPTP server should listen on. Authentication This setting is for specifying the user database source for PPTP authentication. Three sources can be selected: Local User Accounts, LDAP Server, or RADIUS Server. Local User Accounts - User accounts are stored in the Pepwave routerlocally. You can add/modify/delete accounts in the User Accounts table. LDAP Server - Authenticate with an external LDAP server. This has been tested with OpenLDAP servers where passwords are NTLM hashed. Active Directory is not supported. (You can choose to use RADIUS to authenticate with a Windows server.) RADIUS Server - Authenticate with an external RADIUS server. This has been tested with Microsoft Windows Internet Authentication Service and FreeRADIUS servers where passwords are NTLM hashed or in plain text. User Accounts This setting allows you to define PPTP user accounts for authentication via local user accounts. Click Add to input username and password to create an account. After adding the user accounts, you can click on a username to edit the account password. Click to delete the account in its corresponding row. 19.3 Certificate Manager This section allows you to assign certificates for local VPN and web admin SSL. The local keys will not be transferred to another device by any means. 19.4 Service Forwarding Service forwarding settings are located at Advanced>Misc. Settings>Service Forwarding. Service Forwarding SMTP Forwarding When this option is enabled, all outgoing SMTP connections destined for any host at TCP port 25 will be intercepted. These connections will be redirected to a specified SMTP server and port number. SMTP server settings for each WAN can be specified http://www.pepwave.com 113 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual after selecting Enable. Web Proxy Forwarding When this option is enabled, all outgoing connections destined for the proxy server specified in Web Proxy Interception Settings will be intercepted. These connections will be redirected to a specified web proxy server and port number. Web proxy interception settings and proxy server settings for each WAN can be specified after selecting Enable. DNS Forwarding When this option is enabled, all outgoing DNS lookups will be intercepted and redirected to the built-in DNS name server.If any LAN device is using the DNS name servers of a WAN connection, you may want to enable this option to enhance the DNS availability without modifying the DNS server setting of the clients. The built-in DNS name server will distribute DNS lookups to corresponding DNS servers of all available WAN connections. In this case, DNS service will not be interrupted, even if any WAN connection is down. Custom Service Forwarding When this option is enabled, incoming connections from specified ports will be intercepted and forwarded to a local server. 19.4.1 SMTP Forwarding Some ISPs require their users to send e-mails via the ISP’s SMTP server. All outgoing SMTP connections are blocked except those connecting to the ISP’s.Pepwave routers support intercepting and redirecting all outgoing SMTP connections (destined for TCP port 25) via a WAN connection to the WAN’s corresponding SMTP server. To enable the feature, select Enable under SMTP Forwarding Setup. Check Enable Forwardingfor the WAN connection(s) that needs forwarding. Under SMTP Server, enter the ISP’s e-mail server host name or IP address.Under SMTP Port, enter the TCP port number for each WAN. The Pepwave routerwill intercept SMTP connections.Choose a WAN port according to the outbound policy, and then forward the connection to the SMTP server if the chosen WAN has enabled forwarding. If the forwarding is disabled for a WAN connection, SMTP connections for the WAN will be simply be forwarded to the connection’s original destination. Note If you want to route all SMTP connections only to particular WAN connection(s), you should create a custom rule in outbound policy (see Section 14.2). http://www.pepwave.com 114 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 19.4.2 Web Proxy Forwarding When this feature is enabled, the Pepwave routerwill intercept all outgoing connections destined for the proxy server specified in Web Proxy Interception Settings, choose a WAN connection with reference to the outbound policy, and then forward them to the specified web proxy server and port number. Redirected server settings for each WAN can be set here.If forwarding is disabled for a WAN, web proxy connections for the WAN will be simply forwarded to the connection’s original destination. 19.4.3 DNS Forwarding When DNS forwarding is enabled, all clients’ outgoing DNS requests will also be intercepted and forwarded to the built-in DNS proxy server. 19.4.4 Custom Service Forwarding After clicking the enable checkbox, enter your TCP port for traffic heading to the router, and then specify the IP Address and Port of the server you wish to forward to the service to. http://www.pepwave.com 115 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 19.5 Service Passthrough Service passthrough settings can be found at Advanced>Misc. Settings>Service Passthrough. Some Internet services need to be specially handled in a multi-WAN environment.Pepwave routerscan handle these services such that Internet applications do not notice being behind a multi-WAN router. Settings for service passthrough support are available here. Service Passthrough Support SIP Session initiation protocol, aka SIP, is a voice-over-IP protocol. The Pepwave routercan act as a SIP application layer gateway (ALG) which binds connections for the same SIP session to the same WAN connection and translate IP address in the SIP packets correctly in NAT mode. Such passthrough support is always enabled, and there are two modes for selection: Standard Mode and Compatibility Mode. If your SIP server’s signal port number is non-standard, you can check the box Define custom signal ports and input the port numbers to the text boxes. H.323 With this option enabled, protocols that provide audio-visual communication sessions will be defined on any packet network and passthrough the Pepwave router. FTP FTP sessions consist of two TCP connections; one for control and one for data. In a multi-WAN situation, they must be routed to the same WAN connection. Otherwise, problems will arise in transferring files. By default, the Pepwave routermonitors TCP control connections on port 21 for any FTP connections and binds TCP connections of the same FTP session to the same WAN. If you have an FTP server listening on a port number other than 21, you can check Define custom control ports and enter the port numbers in the text boxes. TFTP The Pepwave routermonitors outgoing TFTP connections and routes any incoming TFTP data packets back to the client. Select Enable if you want to enable TFTP passthrough support. IPsec NAT-T This field is for enabling the support of IPsec NAT-T passthrough. UDP ports 500, 4500, and 10000 are monitored by default. You may add more custom data ports that your IPsec system usesby checking Define custom ports. If the VPN contains IPsecsite-to- http://www.pepwave.com 116 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual site VPN traffic, check Route IPsecSite-to-Site VPN and choose the WAN connection to route the traffic to. Port numbers do not need to be the same on both ends of the VPN tunnel. 19.6 GPS Forwarding Using the GPS forwarding feature, some Pepwave routers can automatically send GPS reports to a specified server. To set up GPS forwarding, navigate to Advanced>GPS Forwarding. GPS Forwarding Enable Check this box to turn on GPS forwarding. Server Enter the name/IP address of the server that will receive GPS data. Also specify a port number, protocol (UDP or TCP), and a report interval of between 1 and 10 seconds. Click GPS Report Format NMEA Sentence Type TAIP Sentence Type/TAIP ID (optional) to save these settings. Choose from NMEA or TAIP format for sending GPS reports. If you’ve chosen to send GPS reports in NMEA format, select one or more sentence types for sending the data (GPRMC, GPGGA, GPVTG, GPGSA, and GPGSV). If you’ve chosen to send GPS reports in TAIP format, select one or more sentence types for sending the data (PV—Position / Velocity Solution and CP—Compact Velocity Solution). You can also optionally include an ID number in the TAIP ID field. http://www.pepwave.com 117 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 20 AP Controller The AP controller acts as a centralized controller of Pepwave AP devices. With this feature, users can customize and manage multiple APs from a single Pepwave routerinterface. Special Note Each Pepwaverouter can control a limited number of routers without additional cost. To manage more, a Full Edition license is required. Please contact your Authorized Reseller or the Peplink Sales Team for more information and pricing details. To configure, navigate to the AP tab. 20.1 Wireless SSID This menu is the first one that appears after clicking the AP tab. This screen can also be reached by clicking AP>Wireless SSID. Note the appearance of this screen varies by model. AP Controller AP Management The AP controller for managing Pepwave APs can be enabled by checking this box. When this option is enabled, the AP controller will wait for management connections originating from APs over the LAN on TCP and UDP port 11753. It will also wait for captive portal connections on TCP port 443. An extended DHCP option, CAPWAP Access Controller addresses (field 138), will be added to the DHCP server. A local DNS record, AP Controller, will be added to the local DNS proxy. Permitted AP Access points to manage can be specified here. If Any is selected, the AP controller will manage any AP that reports to it. If Approved List is selected, only APs with serial numbers listed in the provided text box will be managed. http://www.pepwave.com 118 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Current SSID information appears in the SSID section. To edit an existing SSID, click its name in the list. To add a new SSID, click Add. Note that the following settings vary by model. SSID Settings SSID Enable This setting specifies the SSID of the virtual AP to be scanned by Wi-Fi clients. Select Yes to enable the virtual AP. VLAN ID This setting specifies the VLAN ID to be tagged on all outgoing packets generated from this wireless network (i.e., packets that travel from the Wi-Fi segment through the Pepwave AP One unit to the Ethernet segment via the LAN port). The default value of this setting is 0, which means VLAN tagging is disabled (instead of tagged with zero). Broadcast SSID This setting specifies whether or not Wi-Fi clients can scan the SSID of this wireless network. Broadcast SSID is enabled by default. Data Rate A Select Auto to allow the Pepwave routerto set the data rate automatically, or select Fixed and choose a rate from the displayed drop-down menu. Multicast FilterA This setting enables the filtering of multicast network traffic to the wireless SSID. Multicast RateA This setting specifies the transmit rate to be used for sending multicast network traffic. The selected Protocol and Channel Bonding settings will affect the rate http://www.pepwave.com 119 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual options and values available here. IGMP Snooping A To allow the Pepwave routerto listen to internet group management protocol (IGMP) network traffic, select this option. DHCP Option 82 A If you use a distributed DHCP server/relay environment, you can enable this option to provide additional information on the manner in which clients are physically connected to the network. Network Priority (QoS) A Layer 2 Isolation A Band Steering Select from Gold, Silver, and Bronze to control the QoS priority of this wireless network’s traffic. Layer 2 refers to the second layer in the ISO Open System Interconnect model. When this option is enabled, clients on the same VLAN, SSID, or subnet are isolated to that VLAN, SSID, or subnet, which can enhance security. Traffic is passed to upper communication layer(s). By default, the setting is disabled. Band steering allows the Pepwave routerto steer AP clients from the 2.4GHz band to the 5GHz band for better usage of bandwidth. To make steering mandatory, select Enforce. To cause the Pepwave routerto preferentially choose steering, select Prefer. The default for this setting is Disable. - Advanced feature.Click the button on the top right-hand corner to activate. Security Settings Security Policy This setting configures the wireless authentication and encryption methods. Available options areOpen (No Encryption), WPA/WPA2 - Personal, WPA/WPA2 – Enterpriseand Static WEP. Access Control The settings allow administrator to control access usingMACaddress filtering. Available options areNone, Deny all except listed, Accept all except listed, and RADIUS MAC Authentication. Restricted Mode When WPA/WPA2 - Enterprise is configured, RADIUS-based 802.1 x authentication is enabled. Under this configuration, the Shared Key option should be disabled. When using this method, select the appropriate version using the V1/V2 controls. The security level of this method is known to be very high. http://www.pepwave.com 120 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual When WPA/WPA2- Personal is configured, a shared key is used for data encryption and authentication. When using this configuration, the Shared Key option should be enabled. Key length must be between eight and 63 characters (inclusive). The security level of this method is known to be high. The configuration of Static WEP parameters enables pre-shared WEP key encryption. Authentication is not supported by this method. The security level of this method is known to be weak. MAC Address List Connection coming from the MAC addresses in this list will be either denied or accepted based the option selected in the previous field. Please separate each byte with colons (e.g. 11:22:33:44:55:66) RADIUS Server Settings Host Enter the IP address of the primary RADIUS server and, if applicable, the secondary RADIUS server. Secret Enter the RADIUS shared secret for the primary server and, if applicable, the secondary RADIUS server. Authentication Port In field, enter the UDP authentication port(s) used by your RADIUS server(s) or click the Default button to enter 1812. Accounting Port In field, enter the UDP accounting port(s) used by your RADIUS server(s) or click the Default button to enter 1813. http://www.pepwave.com 121 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 20.2 Settings On many Pepwave models, the AP settings screen (AP>Settings) looks similar to the example below: AP Settings SSID These buttons specify which wireless networks will use this AP profile. You can also select the frequencies at which each network will transmit. Please note that the Pepwave routerdoes not detect whether the AP is capable of transmitting at both frequencies. Instructions to transmit at unsupported frequencies will be ignored by the AP. Operating Country This drop-down menu specifies the national/regional regulations which the AP should follow. If a North American region is selected, RF channels 1 to 11 will be available and the maximum transmission power will be 26 dBm (400 mW). If European region is selected, RF channels 1 to 13 will be available. The maximum transmission power will be 20 dBm (100 mW). NOTE: Users are required to choose an option suitable to local laws and regulations. Per FCC regulation, the country selection is not available on all models marketed in US. All US models are fixed to US channels only. Preferred Frequency These buttons determine the frequency at which access points will attempt to broadcast. This feature will only work for APs that can transmit at both 2.4GHz and 5GHz frequencies. 5 GHz Protocol This section displays the 5 GHz protocols your APs are using. 5GHz Channel Bonding There are three options: 20 MHz, 20/40 MHz, and 40 MHz. With this feature enabled, the Wi-Fi system can use two channels at once. Using two channels improves the performance of the Wi-Fi connection. http://www.pepwave.com 122 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 5 GHz Channel This drop-down menu selects the 5 GHz 802.11 channel to be utilized. If Auto is set, the system will perform channel scanning based on the scheduled time set and choose the most suitable channel automatically. 2.4 GHz Protocol This section displays the 2.4GHz protocols your APs are using. 2.4 GHz Channel Bonding There are three options: 20 MHz, 20/40 MHz, and 40 MHz. With this feature enabled, the Wi-Fi system can use two channels at once. Using two channels improves the performance of the Wi-Fi connection. 2.4 GHz Channel This drop-down menu selects the 802.11 channel to be utilized. Available options are from 1 to 11 and from 1 to 13 for the North America region and Europe region, respectively. (Channel 14 is only available when the country is selected as Japan with protocol 802.11b.)If Auto is set, the system will perform channel scanning based on the scheduled time set and choose the most suitable channel automatically. Management VLAN ID This field specifies the VLAN ID to tag to management traffic, such as AP to APcontroller communication traffic. The value is 0 by default, meaning that no VLAN tagging will be applied. NOTE: change this value with caution as alterations may result in loss of connection to the AP controller. Power BoostA Output PowerA With this option enabled, the AP under this profile will transmit using additional power. Please note that using this option with several APs in close proximity will lead to increased interference. This drop-down menu determines the power at which the AP under this profile will broadcast. When fixed settings are selected, the AP will broadcast at the specified power level, regardless of context. When Dynamic settings are selected, the AP will adjust its power level based on its surrounding APs in order to maximize performance. The Dynamic: Auto setting will set the AP to do this automatically. Otherwise, the Dynamic: Manual setting will set the AP to dynamically adjust only of instructed to do so. If you have set Dynamic:Manual, you can go to AP>Toolbox>Auto Power Adj. to give your AP further instructions. Beacon RateA This drop-down menu provides the option to send beacons in different transmit bit rates.The bit rates are 1Mbps, 2Mbps, 5.5Mbps, 6Mbps, and 11Mbps. Beacon IntervalA This drop-down menu provides the option to set the time between each beacon send. Available options are100ms, 250ms, and 500ms. DTIMA This field provides the option to set the frequency for beacon to include delivery traffic indication messages (DTIM). The interval unit is measured in milliseconds. Slot TimeA ACK TimeoutA This field provides the option to modify the unit wait time before it transmits. The default value is 9μs. This field provides the option to set the wait time to receive acknowledgement packet before doing retransmission. The default value is 48μs. Frame With this feature enabled, throughput will be increased by sending two or more data frames in a single transmission. AggregationA - Advanced feature.Click the button on the top right-hand corner to activate. http://www.pepwave.com 123 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Web Administration Settings Enable Check the box to allow thePepwave routerto manage the web admin access information of the AP. Web Access Protocol These buttons specify the web access protocol used for accessing the web admin of the AP. The two available options are HTTP and HTTPS. Management Port This field specifies the management port used for accessing the device. HTTP to HTTPS Redirection This option will be available if you have chosen HTTPS as the Web Access Protocol. With this enabled, any HTTP access to the web admin will redirect to HTTPS automatically. Admin User Name This field specifies the administrator username of the web admin. It is set as admin by default. Admin Password This field allows you to specify a new administrator password. You may also click the Generate button and let the system generate a random password automatically. http://www.pepwave.com 124 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Navigating to AP>Settings on some Pepwave models displays a screen similar to the one shown below: Wi-Fi Radio Settings Operating Country Wi-Fi Antenna This option sets the country whose regulations the Pepwave router follows. Choose from the router's internal or optional external antennas, if so equipped. Important Note Per FCC regulations, the country selection is not available on all models marketed in the US. All US models are fixed to US channels only. Wi-Fi AP Settings Protocol This option allows you to specify whether 802.11b and/or 802.11g client association requests will be accepted. Available options are 802.11ng and 802.11na. By default, 802.11ng is selected. Channel This option allows you to select which 802.11 RF channel will be used.Channel 1 (2.412 GHz) is selected by default. Channel Width Auto (20/40 MHz) and 20 MHz are available. The default setting is Auto (20/40 MHz), which allows both widths to be used simultaneously. Output Power This option is for specifying the transmission output power for the Wi-Fi AP.There are 4 relative power levels available – Max, High, Mid, and Low. The actual output power will be bound by the regulatory limits of the selected country. Beacon RateA This option is for setting the transmit bit rate for sending a beacon. By default, 1Mbps is http://www.pepwave.com 125 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual selected. Beacon IntervalA DTIMA Slot TimeA ACK TimeoutA Frame AggregationA Guard IntervalA This option is for setting the time interval between each beacon. By default, 100ms is selected. This field allows you to set the frequency for the beacon to include a delivery traffic indication message. The interval is measured in milliseconds. The default value is set to 1 ms. This field is for specifying the wait time before the Surf SOHO transmits a packet. By default, this field is set to 9 µs. This field is for setting the wait time to receive an acknowledgement packet before performing a retransmission.By default, this field is set to 48 µs. This option allows you to enable frame aggregation to increase transmission throughput. This setting allows choosing a short or long guard period interval for your transmissions. - Advanced feature, please click the button on the top right-hand corner to activate. 20.3 Toolbox Tools for managing firmware packs can be found atAP>Toolbox. Firmware Packs Here, you can manage the firmware of your AP. Clicking on will result in information regarding each firmware pack. To receive new firmware packs, you can clickCheck for Updates to download new packs, or you can click Manual Upload to manually upload a firmware pack. Click Default to define which firmware pack is default. http://www.pepwave.com 126 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 21 System Settings 21.1 Admin Security There are two types of user accounts available for accessing the web admin: admin and user. They represent two user levels: the admin level has full administration access, while the user level is read-only. The user level can access only the device's status information; users cannot make any changes on the device. Admin account UI User account UI A web login session will be logged out automatically when it has been idle longer than the Web Session Timeout. Before the session expires, you may click the Logout button in the web admin to exit the session. 0 hours 0 minutes signifies an unlimited session time. This setting should be used only in special situations, as it will lower the system security level if users do not logout before closing the browser.The default is 4 hours, 0 minutes. For security reasons, after logging in to the web admin Interface for the first time, it is recommended to change the administrator password. Configuring the administration interface to be accessible only from the LAN can further improve system security.Administrative settings configuration is located atSystem>Admin Security. http://www.pepwave.com 127 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Admin Settings Router Name Admin User Name Admin Password This field allows you to define a name for this Pepwave router.By default, Router Name is set as MAX_XXXX or Surf_SOHO_XXXX, where XXXX refers to the last 4 digits of the unit’s serial number. Admin User Name is set as admin by default,but can be changed, if desired. This field allows you to specify a new administrator password. Confirm Admin Password This field allows you to verify and confirm the new administrator password. Read-only User Name Read-only User Name is set as user by default, but can be changed, if desired. User Password This field allows you to specify a new user password. Once the user password is set, the read-only user feature will be enabled. Confirm User Password This field allows you to verify and confirm the new user password. Web Session Timeout This field specifies the number of hours and minutes that a web session can remain idle before the Pepwave routerterminatesits access to the web admin interface.By default, it is set to 4 hours. http://www.pepwave.com 128 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Authentication by RADIUS With this box is checked, the web admin will authenticate using an external RADIUS server. Authenticated users are treated as either "admin" with full read-write permission or “user” with read-only access.Local admin and user accounts will be disabled. When the device is not able to communicate with the external RADIUS server, local accounts will be enabled again for emergency access. Additional authentication options will be available once this box is checked. Auth Protocol This specifies the authentication protocol used. Available options are MS-CHAP v2 and PAP. Auth Server This specifies the access address and port of the external RADIUS server. Auth Server Secret This field is for entering the secret key for accessing the RADIUS server. Auth Timeout Accounting Server Accounting Server Secret Network Connection CLI SSH CLI SSH Port CLI SSH Access This option specifies the time value for authentication timeout. This specifies the access address and port of the external accounting server. This field is for entering the secret key for accessing the accounting server. This option is for specifying the network connection to be used for authentication. Users can choose from LAN, WAN, and VPN connections. The CLI (command line interface) can be accessed via SSH. This field enables CLI support. For additional information regarding CLI, please refer to Section21.14. This field determines the port on which clients can access CLI SSH. This menu allows you to choose between granting access to LAN and WAN clients, or to LAN clients only. This option is for specifying the protocol(s) through which the web admin interface can be accessed: Security Web Admin Port HTTP HTTPS HTTP/HTTPS This field is for specifying the port number on which the web admin interface can be accessed. This option is for specifying the network interfaces through which the web admin interface can be accessed: Web Admin Access LAN only LAN/WAN If LAN/WAN is chosen, theWAN Connection Access Settings form will be displayed. http://www.pepwave.com 129 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual WAN Connection Access Settings This field allows you to restrict web admin access only from defined IP subnets. Allowed Source IP Subnets Allow access from the following IP subnets only - Restrict web admin access only from the defined IP subnets. When this is chosen, a text input area will be displayed beneath: The allowed IP subnet addresses should be entered into this text area. Each IP subnet must be in form of w.x.y.z/m, where w.x.y.z is an IP address (e.g.,192.168.0.0), andm is the subnet mask in CIDR format, which is between 0 and 32 inclusively (For example,192.168.0.0/24). To define multiple subnets, separate each IP subnet one in a line. For example: Allowed WAN IP Address(es) Any - Allow web admin accesses to be from anywhere, without IP address restriction. 192.168.0.0/24 10.8.0.0/16 This is to choose which WAN IP address(es) the web server should listen on. http://www.pepwave.com 130 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 21.2 Firmware Pepwave routerfirmware is upgradeable through the web admin interface. Firmware upgrade functionality is located atSystem>Firmware. There are two ways to upgrade the unit.The first method is through an online download.The second method is to upload a firmware file manually. To perform an online download, click on the Check for Firmware button. The Pepwave routerwill check online for new firmware. If new firmware is available, the Pepwave routerwill automatically download the firmware.The rest of the upgrade process will be automatically initiated. You may also download a firmware image from the Peplink website and update the unit manually. To update using a firmware image, click Choose File to select the firmware file from the local computer, and thenclick Manual Upgradeto send the firmware to the Pepwave router. It will then automatically initiate the firmware upgrade process. Please note that all Peplink devices can store two different firmware versions in two different partitions. A firmware upgrade will always replace the inactive partition. If you want to keep the inactive firmware, you can simply reboot your device with the inactive firmware and then perform the firmware upgrade. Important Note The firmware upgrade process may not necessarily preserve the previous configuration, and the behavior varies on a case-by-case basis. Consult the release notes for the particular firmware version before installing.Do not disconnect the power during firmware upgrade process.Do not attempt to upload a non-firmware file or a firmware file that is not supported by Peplink.Upgrading the Pepwave routerwith an invalid firmware file will damage the unit and may void the warranty. Important Note If the firmware is rolled back from 5.x to 4.x, the configurations will be lost. http://www.pepwave.com 131 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 21.3 Time Time Settings enables the system clock of the Pepwave routerto be synchronized with a specified time server. Time settings are located atSystem>Time. Time Settings Time Zone Time Server This specifies the time zone (along with the corresponding Daylight Savings Time scheme).The Time Zone value affects the time stamps in the Pepwave router’s event log and e-mail notifications. CheckShow all to show all time zone options. This setting specifies the NTP network time server to be utilized by the Pepwave router. 21.4 Email Notification Email notification functionality provides a system administrator with up-to-date information on network status. The settings for configuring email notifications are found at System>Email Notification. Email Notification Settings Email Notification This setting specifies whether or not to enable email notification.If Enable is checked, the Pepwave routerwill send email messages to system administrators when the WAN status changesor when new firmware is available.If Enable is not checked, email notification is disabled and the Pepwave routerwill not send email messages. http://www.pepwave.com 132 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual SMTP Server SSL Encryption This setting specifies the SMTP server to be used for sending email. If the server requires authentication, check Require authentication. Check the box to enable SMTPS. When the box is checked, SMTP Port will be changed to 465 automatically. SMTP Port This field is for specifying the SMTP port number. By default, this is set to 25; when SSL Encryption is checked, the default port number will be set to 465. You may customize the port number by editing this field. Click Default to restore the number to its default setting. SMTP User Name / Password This setting specifies the SMTP username and password while sending email. These options are shown only ifRequire authentication is checked in the SMTP Server setting. Confirm SMTP Password This field allows you to verify and confirm the new administrator password. Sender’s Email Address This setting specifies the email address the Pepwave router will use to send reports. Recipient’s Email Address This setting specifies the email address(es) to which the Pepwave routerwill send email notifications. For multiple recipients, separate each email addresses using the enter key. After you have finished setting up email notifications, you can click the Test Email Notificationbutton to test the settings before saving. After Test Email Notification is clicked, you will see this screen to confirm the settings: ClickSend Test Notification to confirm. In a few seconds, you will see a message with detailed test results. http://www.pepwave.com 133 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 21.5 Event Log Event log functionality enables event logging at a specified remote syslog server.The settings for configuring the remote system log can be found at System>Event Log. Event Log Settings Remote Syslog This setting specifies whether or not to log events at the specified remote syslog server. Remote Syslog Host This setting specifies the IP address or hostname of the remote syslog server. The Pepwave router can also send push notifications to mobile devices that have our Mobile Router Utility installed. Check the box to activate this feature. Push Events For more information on the Router Utility, go to: www.peplink.com/products/router-utility http://www.pepwave.com 134 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 21.6 SNMP SNMPor simple network management protocol is an open standard that can be used to collect information about the Pepwave router.SNMP configuration is located atSystem>SNMP. SNMP Settings SNMP Device Name SNMP Port This field shows the router name defined atSystem>Admin Security. This option specifies the port which SNMP will use. The default port is 161. SNMPv1 This option allows you to enable SNMP version 1. SNMPv2 This option allows you to enable SNMP version 2. SNMPv3 This option allows you to enable SNMP version 3. To add a community for either SNMPv1 or SNMPv2, click theAdd SNMP Communitybutton in the Community Nametable, upon which the following screen is displayed: http://www.pepwave.com 135 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual SNMP Community Settings Community Name Allowed Source Subnet Address This setting specifies the SNMP community name. This setting specifies a subnet from which access to the SNMP server is allowed.Enter subnet address here (e.g.,192.168.1.0) and select the appropriate subnet mask. To define a user name for SNMPv3, click Add SNMP User in the SNMPv3 User Name table, upon which the following screen is displayed: SNMPv3 User Settings User Name This setting specifies a user name to be used in SNMPv3. This setting specifies via a drop-down menu one of the following valid authentication protocols: Authentication Protocol NONE MD5 SHA When MD5 or SHA is selected, an entry field will appear for the password. This setting specifies via a drop-down menu one of the following valid privacy protocols: Privacy Protocol NONE DES When DES is selected, an entry field will appear for the password. http://www.pepwave.com 136 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 21.7 InControl InControl is a cloud-based service which allows you to manage all of your Peplink and Pepwave devices with one unified system. With it, you can generate reports, gather statistics, and configure your devices automatically. All of this is now possible with InControl. When this check box is checked, the device's status information will be sent to the Peplink InControl system. This device's usage data and configuration will be sent to the system if you enable the features in the system. Alternately, you could also privately host InControl. Simply check the box beside the “Privately Host InControl” open, and enter the IP Address of your InControl Host. You can sign up for an InControl account at https://incontrol2.peplink.com/. You can register your devices under the account, monitor their status, see their usage reports, and receive offline notifications. http://www.pepwave.com 137 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 21.8 Configuration Backing up Pepwave router settings immediately after successful completion of initial setup is strongly recommended.The functionality to download and upload Pepwave routersettings is found atSystem>Configuration. Note that available options vary by model. Configuration Restore Configuration to Factory Settings The Restore Factory Settings button is to reset the configuration to factory default settings. After clicking the button, you will need to click the Apply Changes button on the top right corner to make the settings effective. Download Active Configurations Click Download to backup the current active settings. Upload Configurations To restore or change settings based on a configuration file, click Choose File to locate the configuration file on the local computer, and then click Upload. The new settings can then be applied by clicking the Apply Changes button on the page header, or you can cancel the procedure by pressing discard on the main page of the web admin interface. Upload Configurations from High Availability Pair In a high availability (HA) configuration, aPepwave router can quickly load the configuration of its HA counterpart. To do so, click the Upload button.After loading the settings, configure the LAN IP address of the Pepwve routerso that it is different from the HA counterpart. http://www.pepwave.com 138 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 21.9 Feature Add-ons Some Pepwave routershave features that can be activated upon purchase. Once the purchase is complete, you will receive an activation key. Enter the key in the Activation Key field, click Activate, and then click Apply Changes. 21.10 Reboot This page provides a reboot button for restarting the system. For maximum reliability, the Pepwave router can equip with two copies of firmware.Each copy can be a different version. You can select the firmware version you would like to reboot the device with. The firmware marked with (Running) is the current system boot up firmware. Please note that a firmware upgrade will always replace the inactive firmware partition. http://www.pepwave.com 139 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 21.11 Ping The ping test tool sendspings through a specified Ethernet interface or a SpeedFusionTM VPN connection. You can specify the number of pings in the field Number of times,to a maximum number of 10 times. Packet Size can be set to a maximum of 1472 bytes.The ping utility is located at System>Tools>Ping, illustrated below: Tip A system administrator can use theping utility to manually check the connectivity of a particular LAN/WAN connection. http://www.pepwave.com 140 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 21.12 Traceroute Test The traceroute test tool traces the routing path to the destination through a particular Ethernet interface or a SpeedFusionTM connection.The traceroute test utility is located at System>Tools>Traceroute. Tip A system administrator can use the traceroute utility to analyze the connection path of a LAN/WAN connection. 21.13 PepVPN Test The PepVPN Test tool can help to test the throughput between different VPN peers. You can define the Test Type,Direction, and Duration of the test, and press Go!to perform the throughput test. The VPN test utility is located at System>Tools>PepVPN Test, illustrated as follows: http://www.pepwave.com 141 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 21.14 CLI (Command Line Interface Support) The CLI (command line interface) can be accessed via SSH. This field enables CLI support.The below settings specify which TCP port and which interface(s) should accept remote SSH CLI access. The user name and password used for remote SSH CLI access are the same as those used for web admin access. http://www.pepwave.com 142 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 22 Status 22.1 Device System information is located at Status>Device. System Information Router Name Model Product Code Hardware Revision Serial Number Firmware This is the name specified in the Router Name field located atSystem>Admin Security. This shows the model name and number of this device. If your model uses a product code, it will appear here. This shows the hardware version of this device. This shows the serial number of this device. This shows the firmware version this device is currently running. PepVPN Version This shows the current PepVPN version. Modem Support Version This shows the modem support version. For a list of supported modems, click Modem Support List. Host Name Uptime System Time Diagnostic Report The host name assigned to the Pepwave router appears here. This shows the length of time since the device has been rebooted. This shows the current system time. The Downloadlink is for exporting a diagnostic report file required for system investigation. http://www.pepwave.com 143 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Remote Assistance Click Turn on to enable remote assistance. The second table shows the MAC address of each LAN/WAN interface connected.To view your device’s End User License Agreement (EULA), click . Important Note If you encounter issues and would like to contact the PepwaveSupport Team (http://www.pepwave.com/contact/), please download the diagnostic report file and attach it along with a description of your issue. In Firmware 5.1 or before, the diagnostic report file can be obtained at System>Reboot. 22.1.1 GPS Data The MAX HD2and HD2 IP67automatically store up to seven days of GPS location data in GPS eXchange format (GPX). To review this data using third-party applications, click Status>Deviceand then download your GPX file. The Pepwave MAX BR1, HD2,and HD2 IP67 export real-time location data in NMEA format through the LAN IP address at TCP port 60660. It is accessible from the LAN or over a SpeedFusion connection. To access the data via a virtual serial port, install a virtual serial port driver.Visit http://www.peplink.com/index.php?view=faq&id=294 to download the driver. http://www.pepwave.com 144 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 22.2 Active Sessions Information on active sessions can be found at Status>Active Sessions>Overview. This screen displays the number of sessions initiated by each application. Click on each service listing for additional information. This screen also indicates the number of sessions initiated by each WAN port. In addition, you can see which clients are initiating the most sessions. http://www.pepwave.com 145 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual You can also perform a filtered search for specific sessions. You can filter by subnet, port, protocol, and interface. To perform a search, navigate to Status>Active Sessions>Search. This Active Sessions section displays the active inbound/outbound sessions of each WAN connection on the Pepwave router.A filter is available to sort active session information.Enter a keyword in the field or check one of the WAN connection boxes for filtering. http://www.pepwave.com 146 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 22.3 Client List The client list table is located at Status>Client List. It lists DHCP and online client IP addresses, names (retrieved from the DHCP reservation table or defined by users), current download and upload rate, and MAC address. Clients can be imported into the DHCP reservation table by clicking the button on the right. You can update the record after import by going to Network>LAN. If the PPTP server (see Section 19.2), SpeedFusionTM (see Section 12.1), or AP controller (see Section 20) is enabled, you may see the corresponding connection name listed in the Namefield. 22.4 WINS Client The WINS client list table is located at Status>WINS Client. The WINS client table lists the IP addresses and names of WINS clients. This option will only be available when you have enabled the WINS server (navigation: Network>Interfaces>LAN). The names of clients retrieved will be automatically matched into the Client List (see previous section). Click Flush All to flush all WINS client records. http://www.pepwave.com 147 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 22.5 UPnP / NAT-PMP The table that shows the forwarded ports under UPnP and NAT-PMP protocols is located at Status>UPnP/NAT-PMP. This section appears only if you have enabled UPnP / NAT-PMP as mentioned in Section 15.1.1. Click to delete a single UPnP / NAT-PMP record in its corresponding row. To delete all records, click Delete All on the right-hand side below the table. Important Note UPnP / NAT-PMP records will be deleted immediately after clicking the button need to click Save or Confirm. or Delete All, without the 22.6 SpeedFusion Status Current SpeedFusionTM status information is located at Status>SpeedFusionTM. Details about SpeedFusionTM connection peers appears as below: Click on the corresponding peer name to explore the WAN connection(s) status and subnet information of each VPN peer. http://www.pepwave.com 148 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Click the button for a chart displaying real-time throughput, latency, and droprate information for each WAN connection. When pressing the button, the following menu will appear: http://www.pepwave.com 149 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual After clicking the icon, the following menu appears: Select the L2 protocol (TCP/UDP), direction, and duration and click the Start button to begin the general throughput test. http://www.pepwave.com 150 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual The bandwidth bonding feature of PepVPN occurs when multiple WAN lines from one end merge with multiple WAN lines from the other end. For this to happen, each WAN line needs to form a connection with all the WAN lines on the opposite end. The function of the PepVPN analyzer is to report the throughput, packet loss, and latency of all possible combinations of connections. Please note that the PepVPN Analyzer will temporarily interrupt VPN connectivity and will restore after test. After clicking the icon, the analyzer will require several minutes to perform its analysis depending the number of WAN links in the SpeedFusionTM Tunnel. Once the test the complete, the report will appear: "O" indicates that specific WAN / Tunnel is active for that particular test. "Tx Avg." is the averaged throughput across the full 10 seconds time, while "Tx Max." is the averaged throughput of the fastest 30% of time. http://www.pepwave.com 151 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 22.7 Event Log Event log information is located at Status>Event Log. The log section displays a list of events that has taken place on the Pepwave router. CheckAutoRefresh to refresh log entries automatically. Click the Clear Log button to clear the log. Bandwidth This section shows bandwidth usage statistics and is located at Status>Bandwidth. Bandwidth usage at the LAN while the device is switched off (e.g., LAN bypass) is neither recorded nor shown. http://www.pepwave.com 152 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 22.8.1 Real-Time The Data transferred since installationtable indicates how much network traffic has been processed by the device since the first bootup. The Data transferred since last reboot table indicates how much network traffic has been processed by the device since the last bootup. http://www.pepwave.com 153 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 22.8.2 Hourly This page shows the hourly bandwidth usage for all WAN connections, with the option of viewing each individual connection. Select the desired connection to check from the drop-down menu. http://www.pepwave.com 154 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 22.8.3 Daily This page shows the daily bandwidth usage for all WAN connections, with the option of viewing each individual connection. Select the connection to check from the drop-down menu. If you have enabled the Bandwidth Monitoringfeature, the Current Billing Cycletable for that WAN connection will be displayed. Click on a date to view the client bandwidth usage of that specific date. This feature is not available if you have selected to view the bandwidth usage of only a particular WAN connection. The scale of the graph can be set to display megabytes(MB) or gigabytes(GB). All WAN Daily Bandwidth Usage http://www.pepwave.com 155 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual 22.8.4 Monthly This page shows the monthly bandwidth usage for each WAN connection. If you have enabled theBandwidth Monitoringfeature, you can check the usage of each particular connection and view the information by Billing Cycle or by Calendar Month. Click the first two rows to view the client bandwidth usage in the last two months. This feature is not available if you have chosen to view the bandwidth of an individual WAN connection. The scale of the graph can be set to display megabytes(MB)or gigabytes(GB). All WAN Monthly Bandwidth Usage http://www.pepwave.com 156 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Ethernet WAN Monthly Bandwidth Usage Tip By default, the scale of data size is in MB. 1GB equals 1024MB. http://www.pepwave.com 157 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Appendix A. Restoration of Factory Defaults To restore the factory default settings on a Pepwave router, follow the steps below: 1. Locate the reset button on the front or back panel of the Pepwave router. 2. With a paper clip, press the reset button and hold it for at least 10 seconds, until the unit reboots itself. Afterthe Pepwave router finishes rebooting, the factory default settings will be restored. Important Note All previous configurations and bandwidth usage data will be lost after restoring factory default settings. Regular backup of configuration settings is strongly recommended. http://www.pepwave.com 158 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Appendix B. Declaration 1. The device supports time division technology 2. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from thatto which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. IMPORTANT NOTE FCC Radiation Exposure Statement (for MAX700/ HD2/ HD2 IP67/ BR1/ BR1 Slim LTE) This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. FCC Radiation Exposure Statement (for MAX On-The-Go) http://www.pepwave.com 159 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. 1. 20cm minimum when the product is operated alone without co-transmitting with a plug-in 3G USB dongle device. 2. 65cm minimum when the product is operated with a plug-in 3G USB device which has maximum of 7W ERP output power. 3. For co-transmission scenario which is not covered above, please consult the RF technician or device supplier. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. 3. CE Statement for Pepwave Routers Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: EN 60950-1: 2006 + A11 : 2009+A1 : 2010+ A12: 2011 Safety of Information Technology Equipment EN50385 : 2002 / Article 3(1)(a) Product standard to demonstrate the compliance of radio base stations and fixed terminal stations for wireless telecommunication systems with the basic restrictions or the reference levels related to human exposure to radio frequency electromagnetic fields (110MHz - 40 GHz) - General public EN 300 328 V1.7.1: 2006 Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive EN 301 908-1 V5.2.1: 2011 Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks; Part 1: Harmonized EN for IMT-2000, introduction and common requirements, covering essential requirements of article 3.2 of the R&TTE Directive http://www.pepwave.com 160 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual EN 301 511 V9.0.2: 2003 Global System for Mobile communications (GSM); Harmonized standard for mobile stations in the GSM 900 and DCS 1800 bands covering essential requirements under article 3.2 of the R&TTE directive (1999/5/EC) EN 301 489-1 V1.9.2: 2008 Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements EN 301 489-7 V1.3.1: 2005 ElectroMagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment ad services; Part 7: Specific conditions for mobile and portable radio and ancillary equipment of digital cellular radio telecommunications systems (GSM and DCS) EN 301 489-17 V2.2.1: 2012 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment EN 301 489-24 V1.5.1: 2010 Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 24: Specific conditions for IMT-2000 CDMA Direct Spread (UTRA) for Mobile and portable (UE) radio and ancillary equipment Česky [Czech] Dansk [Danish] Deutsch [German] Eesti [Estonian] English 0081 [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Undertegnede [fabrikantens navn] erklæ rer herved, at fø lgende udstyr [udstyrets typebetegnelse] overholder de væ sentlige krav og ø vrige relevante krav i direktiv 1999/5/EF. Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in Ü bereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. http://www.pepwave.com 161 Copyright @ 2015 Pepwave Pepwave MAX and Surf User Manual Español [Spanish] Ελληνική [Greek] Français [French] Italiano [Italian] Latviski [Latvian] Lietuvių [Lithuanian] Nederlands [Dutch] Malti [Maltese] Magyar [Hungarian] Polski [Polish] Português [Portuguese] Slovensko [Slovenian] Slovensky [Slovak] Suomi [Finnish] Svenska [Swedish] Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ΔΗΛΩΝΕΙ ΟΤΙ [type of equipment] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ. Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of equipment / iekārtas tips] atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem. Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus]megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. [Nome do fabricante] declara que este [tipo de equipamento] está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. [Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. [Meno výrobcu] týmto vyhlasuje, že [typ zariadenia]spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES. [Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. http://www.pepwave.com 162 Copyright @ 2015 Pepwave What are we doing at the moment? Follow us on Twitter! http://twitter.com/Peplink Want to know more about us? Add us on Facebook! http://www.facebook.com/p eplink Difficulties when configuring the device? Visit Our YouTube Channel! http://www.youtube.com/PeplinkC hannel Contact Us: Address: Sales United States Office 800 West El Camino Real, Mountain View CA 94040 United States Tel: +1 (650) 450 9669 Fax: +1 (866) 625 4664 http://www.pepwave.com/contact/sales/ Support http://www.pepwave.com/contact/ Business Development and Partnerships http://www.pepwave.com/partners/channelpartner-program/ Hong Kong Office A5, 5/F, HK Spinners Industrial Building, Phase 6, 481 Castle Peak Road, Cheung Sha Wan, Hong Kong Tel: +852 2990 7600 Fax: +852 3007 0588
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Create Date : 2015:06:02 11:14:26+08:00 Creator Tool : Microsoft® Office Word 2007 Modify Date : 2015:06:23 14:21+08:00 Metadata Date : 2015:06:23 14:21+08:00 Format : application/pdf Creator : Peplink Ltd. Title : Pepwave MAX User Manual Producer : Microsoft® Office Word 2007 Document ID : uuid:66bf48c3-d800-45e0-ac4c-5a37d03dc7f6 Instance ID : uuid:1ce3a8f1-a484-49d6-9845-c2b31463ccf4 Page Count : 163 Language : zh-TW Author : Peplink Ltd.EXIF Metadata provided by EXIF.tools