Pismolabs Technology P1AC4 Pepwave / Peplink / Pismo Wireless Product User Manual 1 rev 2

Download:
Mirror Download [FCC.gov]
Document ID	3570572
Application ID	0SXdCC8l6BNbO4x4Z14/6A==
Document Description	Users Manual-1_rev 2.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	443.07kB (5538422 bits)
Date Submitted	2017-09-20 00:00:00
Date Available	2017-09-20 00:00:00
Creation Date	2017-09-18 20:56:09
Producing Software	Microsoft: Print To PDF
Document Lastmod	2017-09-19 17:55:27
Document Title	Microsoft Word - MAX_BR1_MK2_UserManual_Rev1_Sep18_2017_PIsmo_Labs_Technology_Ltd_170918_2032p
Document Author:	victorchu

Pepwave MAX and Surf
User Manual
Pepwave Products:
MAX 700/HD2/HD2 IP67/HD2 mini/HD4/Transit/Hotspot/BR1/BR1 MK2/
BR1 Mini/BR1 Slim/BR1 ENT/BR1 Pro LTE/BR1 IP55/BR2 IP55/On-The-Go/MAX
HD2/HD4 with MediaFast/Device Connector/ Surf SOHO
Pepwave Firmware 6.3
September 2017
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. Copyright © 2017 Pepwave Ltd. All Rights Reserved.
Pepwave and the Pepwave logo are trademarks of Pepwave Ltd. Other brands or products mentioned may
be trademarks or registered trademarks of their respective owners.
Pepwave MAX and Surf User Manual
Table of Contents
INTRODUCTION AND SCOPE ............................................................................................. 6
GLOSSARY........................................................................................................................ 7
PRODUCT FEATURES ........................................................................................................ 8
3.1
3.2
PEPWAVE MAX MOBILE ROUTER OVERVIEW.................................................................. 11
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
4.11
4.12
4.13
4.14
4.15
DROP-IN MODE AND LAN BYPASS: TRANSPARENT DEPLOYMENT ........................................ 34
QOS: CLEARER VOIP .................................................................................................. 34
PER-USER BANDWIDTH CONTROL ................................................................................. 35
HIGH AVAILABILITY VIA VRRP ...................................................................................... 35
USB MODEM AND ANDROID TETHERING........................................................................ 36
BUILT-IN REMOTE USER VPN SUPPORT ......................................................................... 36
SIM-CARD USSD SUPPORT.......................................................................................... 37
INSTALLATION ............................................................................................................... 38
6.1
6.2
6.3
MAX 700 ................................................................................................................ 11
MAX HD2 ............................................................................................................... 13
MAX HD2 IP67 ....................................................................................................... 15
MAX HD2 MINI ........................................................................................................ 16
MAX TRANSIT........................................................................................................... 18
MAX HOTSPOT ......................................................................................................... 19
MAX HD4 ............................................................................................................... 20
MAX BR1 (MK2) ..................................................................................................... 22
MAX BR1 MINI ........................................................................................................ 24
MAX BR1 SLIM ........................................................................................................ 26
MAX BR1 ENT ........................................................................................................ 28
MAX BR1 PRO LTE ................................................................................................... 29
MAX BR1/2 IP55 .................................................................................................... 30
MAX ON-THE-GO ..................................................................................................... 32
SURF SOHO ............................................................................................................. 33
ADVANCED FEATURE SUMMARY .................................................................................... 34
5.1
5.2
5.3
5.4
5.5
5.6
5.7
SUPPORTED NETWORK FEATURES .................................................................................... 8
OTHER SUPPORTED FEATURES ...................................................................................... 10
PREPARATION ............................................................................................................ 38
CONSTRUCTING THE NETWORK ..................................................................................... 39
CONFIGURING THE NETWORK ENVIRONMENT .................................................................. 40
MOUNTING THE UNIT .................................................................................................... 41
7.1
7.2
WALL MOUNT........................................................................................................... 41
CAR MOUNT ............................................................................................................. 41
http://www.pepwave.com
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
7.3
IP67 INSTALLATION GUIDE .......................................................................................... 41
CONNECTING TO THE WEB ADMIN INTERFACE ............................................................... 42
CONFIGURING THE LAN INTERFACE(S) ............................................................................ 44
9.1
9.2
BASIC SETTINGS ......................................................................................................... 44
CAPTIVE PORTAL ........................................................................................................ 54
10 CONFIGURING THE WAN INTERFACE(S) .......................................................................... 56
10.1
10.2
10.3
10.4
10.5
ETHERNET WAN ....................................................................................................... 57
CELLULAR WAN ........................................................................................................ 65
WI-FI WAN ............................................................................................................. 70
WAN HEALTH CHECK ................................................................................................. 76
DYNAMIC DNS SETTINGS ............................................................................................ 78
11 ADVANCED WI-FI SETTINGS............................................................................................ 81
12 MEDIAFAST CONFIGURATION ........................................................................................ 84
12.1
12.2
12.3
SETTING UP MEDIAFAST CONTENT CACHING .................................................................. 84
SCHEDULING CONTENT PREFETCHING............................................................................. 85
VIEWING MEDIAFAST STATISTICS .................................................................................. 86
13 BANDWIDTH BONDING SPEEDFUSIONTM / PEPVPN ......................................................... 88
13.1
13.2
13.3
PEPVPN .................................................................................................................. 89
THE PEPWAVE ROUTER BEHIND A NAT ROUTER .............................................................. 95
SPEEDFUSIONTM STATUS ............................................................................................. 96
14 IPSEC VPN ...................................................................................................................... 97
14.1
IPSEC VPN SETTINGS.................................................................................................. 97
15 OUTBOUND POLICY MANAGEMENT ..............................................................................101
15.1
15.2
OUTBOUND POLICY .................................................................................................. 101
CUSTOM RULES FOR OUTBOUND POLICY ...................................................................... 102
16 INBOUND ACCESS .........................................................................................................111
16.1
PORT FORWARDING SERVICE ...................................................................................... 111
17 NAT MAPPINGS ............................................................................................................114
18 QOS 116
18.1
18.2
18.3
USER GROUPS ......................................................................................................... 116
BANDWIDTH CONTROL .............................................................................................. 117
APPLICATION ........................................................................................................... 117
19 FIREWALL .....................................................................................................................119
19.1
19.2
OUTBOUND AND INBOUND FIREWALL RULES ................................................................. 119
CONTENT BLOCKING ................................................................................................. 124
http://www.pepwave.com
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
19.3
19.4
OSPF & RIPV2 ....................................................................................................... 125
REMOTE USER ACCESS .............................................................................................. 127
MISCELLANEOUS SETTINGS .................................................................................................129
19.5
19.6
19.7
19.8
19.9
19.10
HIGH AVAILABILITY ................................................................................................... 129
PPTP SERVER ......................................................................................................... 132
CERTIFICATE MANAGER ............................................................................................. 133
SERVICE FORWARDING .............................................................................................. 133
SERVICE PASSTHROUGH ............................................................................................. 136
GPS FORWARDING................................................................................................... 137
20 AP CONTROLLER ...........................................................................................................138
20.1
20.2
20.3
WIRELESS SSID ....................................................................................................... 138
SETTINGS ................................................................................................................ 142
TOOLBOX................................................................................................................ 146
21 SYSTEM SETTINGS .........................................................................................................147
21.1
21.2
21.3
21.4
21.5
21.6
21.7
21.8
21.9
21.10
21.11
21.12
21.13
21.14
21.15
21.16
ADMIN SECURITY ..................................................................................................... 147
FIRMWARE.............................................................................................................. 152
TIME...................................................................................................................... 153
SCHEDULE ............................................................................................................... 153
EMAIL NOTIFICATION ................................................................................................ 154
EVENT LOG ............................................................................................................. 156
SNMP................................................................................................................... 158
INCONTROL............................................................................................................. 160
CONFIGURATION ...................................................................................................... 160
FEATURE ADD-ONS ................................................................................................... 162
REBOOT ................................................................................................................. 162
PING...................................................................................................................... 163
TRACEROUTE TEST.................................................................................................... 164
PEPVPN TEST ......................................................................................................... 164
WAKE-ON-LAN ....................................................................................................... 165
CLI (COMMAND LINE INTERFACE SUPPORT) .................................................................. 165
22 STATUS .........................................................................................................................166
22.1
22.2
22.3
22.4
22.5
22.6
22.7
22.8
APPENDIX A.
DEVICE ................................................................................................................... 166
ACTIVE SESSIONS ..................................................................................................... 168
CLIENT LIST ............................................................................................................. 170
WINS CLIENT ......................................................................................................... 170
UPNP / NAT-PMP ................................................................................................. 171
SPEEDFUSION STATUS ............................................................................................... 171
EVENT LOG ............................................................................................................. 175
BANDWIDTH ........................................................................................................... 175
RESTORATION OF FACTORY DEFAULTS......................................................181
http://www.pepwave.com
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
APPENDIX B: DECLARATION ................................................................................................182
http://www.pepwave.com
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Introduction and Scope
Pepwave routers provide link aggregation and load balancing across multiple WAN
connections, allowing a combination of technologies like 3G HSDPA, EVDO, 4G LTE,
Wi-Fi, external WiMAX dongle, and satellite to be utilized to connect to the Internet.
The MAX wireless SD-WAN router series has a wide range of products suitable for
many different deployments and markets. Entry level SD-WAN models such as the MAX
BR1 are suitable for SMEs or branch offices. High-capacity SD-WAN routers such as
the MAX HD2 are suitable for larger organizations and head offices.
This manual covers setting up Pepwave routers and provides an introduction to their
features and usage.
Tips
Want to know more about Pepwave routers? Visit our YouTube Channel for a video introduction!
http://youtu.be/UCkVQThLKO4
http://www.pepwave.com
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Glossary
The following terms, acronyms, and abbreviations are frequently used in this manual:
Term
Definition
3G
3rd Generation standards for wireless communications
4G
4th Generation standards for wireless communications
DHCP
DNS
EVDO
HSDPA
Dynamic Host Configuration Protocol
Domain Name System
Evolution-Data Optimized
High-Speed Downlink Packet Access
HTTP
Hyper-Text Transfer Protocol
ICMP
Internet Control Message Protocol
IP
LAN
MAC Address
Internet Protocol
Local Area Network
Media Access Control Address
MTU
Maximum Transmission Unit
MSS
Maximum Segment Size
NAT
Network Address Translation
PPPoE
QoS
SNMP
Point to Point Protocol over Ethernet
Quality of Service
Simple Network Management Protocol
TCP
Transmission Control Protocol
UDP
User Datagram Protocol
VPN
Virtual Private Network
VRRP
Virtual Router Redundancy Protocol
WAN
Wide Area Network
WINS
Windows Internet Name Service
WLAN
Wireless Local Area Network
http://www.pepwave.com
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Product Features
Pepwave routers enable all LAN users to share broadband Internet connections, and
they provide advanced features to enhance Internet access. Our Max BR wireless
routers support multiple SIM cards. They can be configured to switch from using one
SIM card to another SIM card according to different criteria, including wireless network
reliability and data usage.
Our MAX HD series wireless routers are embedded with multiple 4G LTE modems, and
allow simultaneous wireless Internet connections through multiple wireless networks.
The wireless Internet connections can be bonded together using our SpeedFusion
technology. This allows better reliability, larger bandwidth, and increased wireless
coverage are comparing to use only one 4G LTE modem.
Below is a list of supported features on Pepwave routers. Features vary by model. For
more information, please see peplink.com/products.
3.1
Supported Network Features
3.1.1 WAN













Ethernet WAN connection in full/half duplex
Static IP support for PPPoE
Built-in HSPA and EVDO cellular modems
USB mobile connection(s)
Wi-Fi WAN connection
Network address translation (NAT)/port address translation (PAT)
Inbound and outbound NAT mapping
IPsec NAT-T and PPTP packet passthrough
MAC address clone and passthrough
Customizable MTU and MSS values
WAN connection health check
Dynamic DNS (supported service providers: changeip.com, dyndns.org, noip.org, tzo.com and DNS-O-Matic)
Ping, DNS lookup, and HTTP-based health check
3.1.2 LAN






Wi-Fi AP
Ethernet LAN ports
DHCP server on LAN
Extended DHCP option support
Static routing rules
VLAN on LAN support
http://www.pepwave.com
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
3.1.3 VPN











PepVPN with SpeedFusionTM
PepVPN performance analyzer
X.509 certificate support
VPN load balancing and failover among selected WAN connections
Bandwidth bonding and failover among selected WAN connections
IPsec VPN for network-to-network connections (works with Cisco and Juniper
only)
Ability to route Internet traffic to a remote VPN peer
Optional pre-shared key setting
SpeedFusionTM throughput, ping, and traceroute tests
PPTP server
PPTP and IPsec passthrough
3.1.4 Firewall





Outbound (LAN to WAN) firewall rules
Inbound (WAN to LAN) firewall rules per WAN connection
Intrusion detection and prevention
Specification of NAT mappings
Outbound firewall rules can be defined by destination domain name
3.1.5 Captive Portal



Splash screen of open networks, login page for secure networks
Customizable built-in captive portal
Supports linking to outside page for captive portal
3.1.6 Outbound Policy




Link load distribution per TCP/UDP service
Persistent routing for specified source and/or destination IP addresses per
TCP/UDP service
Traffic prioritization and DSL optimization
Prioritize and route traffic to VPN tunnels with Priority and Enforced algorithms
3.1.7 AP Controller

Configure and manage Pepwave AP devices
http://www.pepwave.com
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual

Review the status of connected APs
3.1.8 QoS




3.2























Quality of service for different applications and custom protocols
User group classification for different service levels
Bandwidth usage control and monitoring on group- and user-level
Application prioritization for custom protocols and DSL/cable optimization
Other Supported Features
User-friendly web-based administration interface
HTTP and HTTPS support for web admin interface
Configurable web administration port and administrator password
Firmware upgrades, configuration backups, ping, and traceroute via web admin
interface
Remote web-based configuration (via WAN and LAN interfaces)
Time server synchronization
SNMP
Email notification
Read-only user for web admin
Shared IP drop-in mode
Authentication and accounting by RADIUS server for web admin
Built-in WINS servers*
Syslog
SIP passthrough
PPTP packet passthrough
Event log
Active sessions
Client list
WINS client list *
UPnP / NAT-PMP
Real-time, hourly, daily, and monthly bandwidth usage reports and charts
IPv6 support
Support USB tethering on Android 2.2+ phones
* Not supported on MAX Surf-On-The-Go, Surf SOHO, and BR1 variants
http://www.pepwave.com
10
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Pepwave MAX Mobile Router Overview
4.1
MAX 700
4.1.1 Panel Appearance
http://www.pepwave.com
11
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
4.1.2 LED Indicators
The statuses indicated by the front panel LEDs are as follows:
Status
Wi-Fi WAN
Wi-Fi AP
OFF
Red
Blinking
red
Green
Status Indicators
System initializing
Booting up or busy
Boot up error
Ready
Wi-Fi AP and Wi-Fi WAN Indicators
OFF
Disconnected
Blinking slowly
Connecting to network
Blinking
ON
OFF
Blinking slowly
Blinking
ON
Connected to network with traffic
Connected to network without traffic
Disabled
Enabled but no client connected
Connected to network with traffic
Client(s) connected to wireless network
LAN and Ethernet WAN Ports
Green LED
Orange LED
Port Type
ON
10 / 100/ 1000 Mbps
Blinking
Data is transferring
No data is being transferred or port is not
connected
OFF
Auto MDI/MDI-X ports
http://www.pepwave.com
12
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
4.2
MAX HD2
4.2.1 Panel Appearance
http://www.pepwave.com
13
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
4.2.2 LED Indicators
The statuses indicated by the front panel LEDs are as follows:
Status
Wi-Fi WAN /
Cellular 1 /
Cellular 2
OFF
Red
Blinking
red
Green
Status Indicators
System initializing
Booting up or busy
Boot up error
Ready
Wi-Fi AP and Wi-Fi WAN Indicators
OFF
Disabled Intermittent
Blinking slowly
Connecting to wireless network(s)
Connected to wireless network(s) with traffic
Blinking
ON
Connected to wireless network(s) without traffic
LAN and Ethernet WAN Ports
Green LED
Orange LED
Port Type
ON
10 / 100 / 1000 Mbps
Blinking
Data is transferring
No data is being transferred or port is not
connected
OFF
Auto MDI/MDI-X ports
http://www.pepwave.com
14
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
4.3
MAX HD2 IP67
4.3.1 Panel Appearance
The statuses indicated by the front panel LEDs are as follows:
Status
OFF
Red
Blinking
red
Green
http://www.pepwave.com
Status Indicators
System initializing
Booting up or busy
Boot up error
Ready
15
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
4.4
MAX HD2 mini
4.4.1 Panel Appearance
http://www.pepwave.com
16
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
4.4.2 LED Indicators
The statuses indicated by the front panel LEDs are as follows:
Status
Cellular 1 /
Cellular 2
OFF
Red
Blinking
red
Green
Status Indicators
System initializing
Booting up or busy
Boot up error
Ready
Cellular WAN Indicators
OFF
Disabled intermittent
Blinking slowly
Connecting to wireless network(s)
Connected to wireless network(s) with traffic
Blinking
ON
Connected to wireless network(s) without traffic
LAN and Ethernet WAN Ports
Green LED
Orange LED
Port Type
ON
10 / 100 / 1000 Mbps
Blinking
Data is transferring
No data is being transferred or port is not
connected
OFF
Auto MDI/MDI-X ports
http://www.pepwave.com
17
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
4.5
MAX Transit
4.5.1 Panel Appearance
4.5.2 LED Indicators
The statuses indicated by the front panel LEDs are as follows:
Status
OFF
Red
Blinking
red
Green
Status Indicators
System initializing
Booting up or busy
Boot up error
Ready
Cellular WAN Indicators
OFF
Disabled intermittent
Blinking slowly
Connecting to wireless network(s)
Cellular 1 /
Cellular 2*
Connected to wireless network(s) with traffic
Blinking
ON
Connected to wireless network(s) without traffic
* For MAX-TST_DUO
LAN and Ethernet WAN Ports
Green LED
Orange LED
Port Type
ON
10 / 100 / 1000 Mbps
Blinking
Data is transferring
No data is being transferred or port is not
connected
OFF
Auto MDI/MDI-X ports
http://www.pepwave.com
18
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
4.6
MAX Hotspot
4.6.1 Panel Appearance
4.6.2 LED Indications
LED Indicators
Status
RED – Access point initializing
GREEN – Access point ready
LAN and Ethernet WAN Ports
Green LED
Orange LED
Port Type
ON
100 Mbps
OFF
10 Mbps
ON
Port is connected without traffic
Blinking
Data is transferring
OFF
Port is not connected
Auto MDI/MDI-X ports
http://www.pepwave.com
19
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
4.7
MAX HD4
4.7.1 Panel Appearance
4.7.2 LED Indicators
The statuses indicated by the front panel LEDs are as follows:
Status
Wi-Fi WAN /
Cellular 1 /
Cellular 2
OFF
Red
Blinking
red
Green
Status Indicators
System initializing
Booting up or busy
Boot up error
Ready
Wi-Fi AP and Wi-Fi WAN Indicators
OFF
Disabled Intermittent
Blinking slowly
Connecting to wireless network(s)
Connected to wireless network(s) with traffic
Blinking
ON
Connected to wireless network(s) without traffic
LAN and Ethernet WAN Ports
Green LED
Orange LED
ON
10 / 100 / 1000 Mbps
Blinking
Data is transferring
No data is being transferred or port is not
connected
OFF
http://www.pepwave.com
20
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Port Type
Auto MDI/MDI-X ports
http://www.pepwave.com
21
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
4.8
MAX BR1 / MAX BR1 MK2
4.8.1 Panel Appearance
MAX BR1 MK2
SMA Cellular
Antenna Connector
SMA Cellular
Antenna Connector
100/1000M
Ethernet LAN
Terminal Block
RP-SMA Wi-Fi
Antenna Connector
http://www.pepwave.com
22
10-30V DC
Terminal Block
100/1000M
Ethernet WAN
Terminal Block
10-30V DC
Connector
RP-SMA Wi-Fi
Antenna Connector
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
4.8.2 LED Indicators
The statuses indicated by the front panel LEDs are as follows:
Status
Wi-Fi
Cellular
OFF
Red
Blinking
red
Green
OFF
Blinking slowly
Blinking
ON
Status Indicators
System initializing
Booting up or busy
Boot up error
Ready
Wi-Fi Indicators
Disabled intermittent
Connecting to wireless network(s)
Connected to wireless network(s) with traffic
Connected to wireless network(s) without traffic
Cellular Indicators
Disabled or no SIM card inserted
Connecting or connected to network(s)
OFF
ON
LAN and Ethernet WAN Ports
Green LED
Orange LED
Port Type
ON
100 Mbps / 1000Mbps (MK2)
OFF
10 Mbps / 100Mbps (MK2)
ON
Port is connected without traffic
Blinking
Data is transferring
OFF
Port is not connected
Auto MDI/MDI-X ports
http://www.pepwave.com
23
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
4.9
MAX BR1 Mini
4.9.1 Panel Appearance
4.9.2 LED Indicators
The statuses indicated by the front panel LEDs are as follows:
Status
Wi-Fi
Cellular
OFF
Red
Blinking
red
Green
OFF
Blinking slowly
Blinking
ON
OFF
ON
http://www.pepwave.com
Status Indicators
System initializing
Booting up or busy
Boot up error
Ready
Wi-Fi Indicators
Disabled intermittent
Connecting to wireless network(s)
Connected to wireless network(s) with traffic
Connected to wireless network(s) without traffic
Cellular Indicators
Disabled or no SIM card inserted
Connecting or connected to network(s)
24
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
A torque requirement of hex connection:
 GPS - Torque requirement is 7.5+/-0.2kg f-cm
 Cellular Main - Torque requirement is 7.5+/-0.2kg f-cm
 Cellular Diversity/AUX - Torque requirement is 7.5+/-0.2kg f-cm
http://www.pepwave.com
25
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
4.10 MAX BR1 Slim
4.10.1 Panel Appearance
4.10.2 LED Indicators
The statuses indicated by the front panel LEDs are as follows:
Status
Wi-Fi
Cellular
OFF
Red
Blinking
red
Green
OFF
Blinking slowly
Blinking
ON
OFF
ON
http://www.pepwave.com
Status Indicators
System initializing
Booting up or busy
Boot up error
Ready
Wi-Fi Indicators
Disabled intermittent
Connecting to wireless network(s)
Connected to wireless network(s) with traffic
Connected to wireless network(s) without traffic
Cellular Indicators
Disabled or no SIM card inserted
Connecting or connected to network(s)
26
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual

LAN and Ethernet WAN Ports
Green LED
Orange LED
Port Type
ON
100 Mbps
OFF
10 Mbps
ON
Port is connected without traffic
Blinking
Data is transferring
OFF
Port is not connected
Auto MDI/MDI-X ports

http://www.pepwave.com
27
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
4.11 MAX BR1 ENT
4.11.1 Panel Appearance
4.11.2 LED Indicators
 The statuses indicated by the front panel LEDs are as follows:
Status
Cellular
OFF
Red
Blinking
red
Green
Status Indicators
System initializing
Booting up or busy
Boot up error
Ready
Cellular Indicators
Disabled or no SIM card inserted
Connecting or connected to network(s)
OFF
ON
LAN and Ethernet WAN Ports
Green LED
Orange LED
Port Type
ON
100 Mbps
OFF
10 Mbps
ON
Port is connected without traffic
Blinking
Data is transferring
OFF
Port is not connected
Auto MDI/MDI-X ports
http://www.pepwave.com
28
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
4.12 MAX BR1 Pro LTE
4.12.1 Panel Appearence
4.12.2 LED Indicators
 The statuses indicated by the front panel LEDs are as follows:
Status
Cellular
OFF
Red
Blinking
red
Green
Status Indicators
System initializing
Booting up or busy
Boot up error
Ready
Cellular Indicators
Disabled or no SIM card inserted
Connecting or connected to network(s)
OFF
ON
LAN and Ethernet WAN Ports
Green LED
Orange LED
Port Type
ON
100 Mbps
OFF
10 Mbps
ON
Port is connected without traffic
Blinking
Data is transferring
OFF
Port is not connected
Auto MDI/MDI-X ports
http://www.pepwave.com
29
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
4.13 MAX BR1/2 IP55
4.13.1 Panel Appearance
4.13.2 LED Indicators
The statuses indicated by the front panel LEDs are as follows:
Status
OFF
Red
Blinking
red
Green
http://www.pepwave.com
Status Indicators
System initializing
Booting up or busy
Boot up error
Ready
30
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Wi-Fi
Cellular
OFF
Blinking slowly
Blinking
ON
Wi-Fi Indicators
Disabled Intermittent
Connecting to wireless network(s)
Connected to wireless network(s) with traffic
Connected to wireless network(s) without traffic
Cellular Indicators
Disabled or no SIM card inserted
Connecting or connected to network(s)
OFF
ON
LAN and Ethernet WAN Ports
Green LED
Orange LED
Port Type
ON
100 Mbps
OFF
10 Mbps
ON
Port is connected without traffic
Blinking
Data is transferring
OFF
Port is not connected
Auto MDI/MDI-X ports
http://www.pepwave.com
31
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
4.14 MAX On-The-Go
4.14.1 Panel Appearance
4.14.2 LED Indicators
The statuses indicated by the front panel LEDs are as follows:
WAN
Wi-Fi
Status
Cellular Indicators
Modem is not attached to the port
Modem is attached to the port
OFF
Green
Wi-Fi Indicators
Disconnected from AP
Connected to AP
OFF
Green
Status Indicators
System initializing
Booting up or busy
Ready
OFF
Red
Green
LAN and Ethernet WAN Ports
Green LED
Orange LED
Port Type
ON
100 Mbps
OFF
10 Mbps
ON
Port is connected without traffic
Blinking
Data is transferring
Auto MDI/MDI-X ports
http://www.pepwave.com
32
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
4.15 Surf SOHO
4.15.1 Panel Appearance
4.15.2 LED Indicators
The statuses indicated by the front panel LEDs are as follows:
Wi-Fi
Status
OFF
Blinking
ON
Continuous
blinking
OFF
Red
Green
Wi-Fi and Status Indicators
Disabled Intermittent
Enabled but no client connected
Client(s) connected to wireless network
Transferring data to wireless network
System initializing
Booting up or busy
Ready state
LAN and Ethernet WAN Ports
Green LED
Orange LED
Port type
ON
100/1000 Mbps
Blinking
Data is transferring
No data is being transferred or port is not
connected
OFF
Auto MDI/MDI-X ports
Wi-Fi Signal
Off
Signal strength
No connection
Wi-Fi signal strength (low, medium, and high)
http://www.pepwave.com
33
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Advanced Feature Summary
5.1
Drop-in Mode and LAN Bypass: Transparent Deployment
As your organization grows, it needs more bandwidth. But modifying your network would require
effort better spent elsewhere. In Drop-in Mode, you can conveniently install your Peplink router
without making any changes to your network. And if the Peplink router loses power for any reason,
LAN Bypass will safely and automatically bypass the Peplink router to resume your original network
connection.
Compatible with: MAX 700, MAX HD2 (All variants), HD4 (All Variants)
5.2
QoS: Clearer VoIP
VoIP and videoconferencing are highly sensitive to latency. With QoS, Peplink routers can detect
VoIP traffic and assign it the highest priority, giving you crystal-clear calls.
http://www.pepwave.com
34
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
5.3
Per-User Bandwidth Control
With per-user bandwidth control, you can define bandwidth control policies for up to 3 groups of
users to prevent network congestion. Define groups by IP address and subnet, and set bandwidth
limits for every user in the group.
5.4
High Availability via VRRP
When your organization has a corporate requirement demanding the highest availability with no
single point of failure, you can deploy two Peplink routers in High Availability mode. With High
Availability mode, the second device will take over when needed.
Compatible with: MAX 700, MAX HD2 (All variants), HD4 (All Variants)
http://www.pepwave.com
35
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
5.5
USB Modem and Android Tethering
For increased WAN diversity, plug in a USB LTE modem as backup. Peplink routers are
compatible with over 200 modem types. You can also tether to smartphones running Android
4.1.X and above.
Compatible with: MAX 700, HD2 (all variants except IP67), HD4 (All variants)
5.6
Built-In Remote User VPN Support
Use L2TP with IPsec to safely and conveniently connect remote clients to your private network.
L2TP with IPsec is supported by most devices, but legacy devices can also connect using PPTP.
Click here for full instructions on setting up L2TP with IPsec.
http://www.pepwave.com
36
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
5.7
SIM-card USSD support
Cellular-enabled routers can now use USSD to check their SIM card’s balance, process pre-paid
cards, and configure carrier-specific services.Click here for full instructions on using USSD.
http://www.pepwave.com
37
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Installation
The following section details connecting Pepwave routers to your network.
6.1
Preparation
Before installing your Pepwave router, please prepare the following as appropriate for
your installation:

At least one Internet/WAN access account and/or Wi-Fi access information

Depending on network connection type(s), one or more of the following:
 Ethernet WAN: A 10/100/1000BaseT UTP cable with RJ45 connector
 USB: A USB modem
 Embedded modem: A SIM card for GSM/HSPA service
 Wi-Fi WAN: Wi-Fi antennas
 PC Card/Express Card WAN: A PC Card/ExpressCard for the
corresponding card slot

A computer installed with the TCP/IP network protocol and a supported web
browser. Supported browsers include Microsoft Internet Explorer 8.0 or above,
Mozilla Firefox 10.0 or above, Apple Safari 5.1 or above, and Google Chrome 18
or above.
http://www.pepwave.com
38
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
6.2
Constructing the Network
At a high level, construct the network according to the following steps:
1.
2.
3.
With an Ethernet cable, connect a computer to one of the LAN ports on the
Pepwave router. Repeat with different cables for up to 4 computers to be
connected.
With another Ethernet cable or a USB modem/Wi-Fi antenna/PC
Card/Express Card, connect to one of the WAN ports on the Pepwave
router. Repeat the same procedure for other WAN ports.
Connect the power adapter to the power connector on the rear panel of the
Pepwave router, and then plug it into a power outlet.
The following figure schematically illustrates the resulting configuration:
http://www.pepwave.com
39
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
6.3
Configuring the Network Environment
To ensure that the Pepwave router works properly in the LAN environment and can
access the Internet via WAN connections, please refer to the following setup
procedures:

LAN configuration
For basic configuration, refer to Section 8, Connecting to the Web Admin
Interface.
For advanced configuration, go to Section 9, Configuring the LAN Interface(s).

WAN configuration
For basic configuration, refer to Section 8, Connecting to the Web Admin
Interface.
For advanced configuration, go to Section 9.2, Captive Portal.
http://www.pepwave.com
40
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Mounting the Unit
7.1
Wall Mount
The Pepwave MAX 700/HD2/On-The-Go can be wall mounted using screws. After
adding the screw on the wall, slide the MAX in the screw hole socket as indicated
below. Recommeneded screw specification: M3.5 x 20mm, head diameter 6mm, head
thickness 2.4mm.
The Pepwave MAX BR1 requires four screws for wall mounting.
7.2
Car Mount
The Pepwave MAX700/HD2 can be mounted in a vehicle using the included mounting
brackets. Place the mounting brackets by the two sides and screw them onto the
device.
7.3
IP67 Installation Guide
Installation instructions for IP67 devices can be found here:
http://download.peplink.com/manual/IP67_Installation_Guide.pdf
http://www.pepwave.com
41
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Connecting to the Web Admin Interface
1. Start a web browser on a computer that is connected with the Pepwave router
through the LAN.
2. To connect to the router’s web admin interface, enter the following LAN IP address
in the address field of the web browser:
http://192.168.50.1
(This is the default LAN IP address for Pepwave routers.)
3. Enter the following to access the web
admin interface.
Username: admin
Password: admin
(This is the default username and
password for Pepwave routers. The
admin and read-only user passwords
can be changed at System>Admin
Security.)
4. After successful login, the Dashboard will be displayed.
The Dashboard shows current WAN, LAN, and Wi-Fi AP statuses. Here, you can
change WAN connection priority and switch on/off the Wi-Fi AP. For further information
on setting up these connections, please refer to Sections 8 and 9.
http://www.pepwave.com
42
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Device Information displays details about the device, including model name, firmware
version, and uptime. For further information, please refer to Section 22.
Important Note
Configuration changes (e.g. WAN, LAN, admin settings, etc.) will take effect only after clicking the Save button at
the bottom of each page. The Apply Changes button causes the changes to be saved and applied.
http://www.pepwave.com
43
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Configuring the LAN Interface(s)
9.1
Basic Settings
LAN interface settings are located at Network>LAN>Basic Settings. Navigating to that
page will result in the following dashboard:
This represents the LAN interfaces that are active on your router (including VLAN). A
grey “X” means that the VLAN is used in other settings and cannot be deleted. You can
find which settings are using the VLAN by hovering over the grey “X”.
Alternatively, a red “X” means that there are no settings using the VLAN. You can delete
that VLAN by clicking the red “X”
Clicking any of the existing LAN interfaces (or creating a new one) will result in the
following
IP Settings
IP Address
The IP address and subnet mask of the Pepwave router on the LAN.
Network Settings
Name
VLAN ID
Inter-VLAN
routing
Enter a name for the LAN.
Enter a number for your VLAN.
Check this box to enable routing between virtual LANs.
http://www.pepwave.com
44
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Captive Portal
Check this box to turn on captive portals.
http://www.pepwave.com
45
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Drop-in Mode Settings
Enable
Drop-in mode eases the installation of Peplink routers on a live network between the
existing firewall and router, such that no configuration changes are required on existing
equipment. Check the box to enable the drop-in mode feature, if available on your model.
WAN for DropIn Mode
Select the WAN port to be used for drop-in mode. If WAN 1 with LAN Bypass is selected,
the high availability feature will be disabled automatically.
Share Drop-In
IPA
Shared IP
AddressA
WAN Default
Gateway
WAN DNS
Servers
When this option is enabled, the passthrough IP address will be used to connect to WAN
hosts (email notification, remote syslog, etc.). The Pepwave router will listen for this IP
address when WAN hosts access services provided by the Pepwave router (web admin
access from the WAN, DNS server requests, etc.).
To connect to hosts on the LAN (email notification, remote syslog, etc.), the default gateway
address will be used. The Pepwave router will listen for this IP address when LAN hosts
access services provided by the Pepwave router (web admin access from the WAN, DNS
proxy, etc.).
Access to this IP address will be passed through to the LAN port if this device is not serving
the service being accessed. The shared IP address will be used in connecting to hosts on
the WAN (email notification, remote syslog, etc.) The device will also listen on the IP
address when hosts on the WAN access services served on this device (web admin access
from the WAN, DNS server, etc.)
Enter the WAN router's IP address in this field. If there are more hosts in addition to the
router on the WAN segment, check the I have other host(s) on WAN segment box and
enter the IP address of the hosts that need to access LAN devices or be accessed by
others.
Enter the selected WAN's corresponding DNS server IP addresses.
- Advanced feature, please click the
button on the top right-hand corner to activate.
Layer 2 PepVPN Bridging
PepVPN
Profiles to
Bridge
Spanning Tree
Protocol
Override IP
The remote network of the selected PepVPN profiles will be bridged with this local LAN,
creating a Layer 2 PepVPN, they will be connected and operate like a single LAN, and any
broadcast or multicast packets will be sent over the VPN.
Click the box will enable STP for this layer 2 profile bridge.
Select "Do not override" if the LAN IP address and local DHCP server should remain
unchanged after the Layer 2 PepVPN is up.
http://www.pepwave.com
46
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Address when
bridge
connected
If you choose to override IP address when the VPN is connected, the device will not act as a
router, and most Layer 3 routing functions will cease to work.
DHCP Server Settings
DHCP Server
When this setting is enabled, the DHCP server automatically assigns an IP address to
each computer that is connected via LAN and configured to obtain an IP address via
DHCP. The Pepwave router’s DHCP server can prevent IP address collision on the LAN.
IP Range &
Subnet Mask
These settings allocate a range of IP addresses that will be assigned to LAN computers by
the Pepwave router’s DHCP server.
Lease Time
This setting specifies the length of time throughout which an IP address of a DHCP client
remains valid. Upon expiration of the lease time, the assigned IP address will no longer be
valid and renewal of the IP address assignment will be required.
DNS Servers
This option allows you to input the DNS server addresses to be offered to DHCP clients. If
Assign DNS server automatically is selected, the Pepwave router’s built-in DNS server
address (i.e., LAN IP address) will be offered.
This option allows you to optionally specify a Windows Internet Name Service (WINS)
server. You may choose to use the built-in WINS server or external WINS servers.
WINS Server
BOOTP
Extended
DHCP Option
When this unit is connected using SpeedFusionTM, other VPN peers can share this unit's
built-in WINS server by entering this unit's LAN IP address in their DHCP WINS Server
setting. Afterward, all PC clients in the VPN can resolve the NetBIOS names of other
clients in remote peers. If you have enabled this option, a list of WINS clients will be
displayed at Status>WINS Clients.
Check this box to enable BOOTP on older networks that still require it.
In addition to standard DHCP options (e.g., DNS server address, gateway address, subnet
mask), you can specify the value of additional extended DHCP options, as defined in RFC
2132. With these extended options enabled, you can pass additional configuration
information to LAN hosts.
To define an extended DHCP option, click the Add button, choose the option to define and
http://www.pepwave.com
47
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
enter its value. For values that are in IP address list format, you can enter one IP address
per line in the provided text area input control. Each option can be defined once only.
DHCP
Reservation
This setting reserves the assignment of fixed IP addresses for a list of computers on the
LAN. The computers to be assigned fixed IP addresses on the LAN are identified by their
MAC addresses. The fixed IP address assignment is displayed as a cross-reference list
between the computers’ names, MAC addresses, and fixed IP addresses.
Name (an optional field) allows you to specify a name to represent the device. MAC
addresses should be in the format of 00:AA:BB:CC:DD:EE. Press
to create a new
record. Press
to remove a record. Reserved client information can be imported from
the Client List, located at Status>Client List. For more details, please refer to Section
22.3.
LAN Physical Settings
Speed
This is the port speed of the LAN interface. It should be set to the same speed as the
connected device to avoid port negotiation problems. When a static speed is set, you may
choose whether to advertise its speed to the peer device. Auto is selected by default. You
can choose not to advertise the port speed if the port has difficulty negotiating with the
peer device.
Static Route Settings
Static Route
This table is for defining static routing rules for the LAN segment. A static route consists of
the network address, subnet mask, and gateway address. The address and subnet mask
values are in w.x.y.z format.
The local LAN subnet and subnets behind the LAN will be advertised to the VPN. Remote
routes sent over the VPN will also be accepted. Any VPN member will be able to route to
the local subnets. Press
to create a new route. Press
to remove a route.
WINS Server Settings
Enable
Check the box to enable the WINS server. A list of WINS clients will be displayed at
Status>WINS Clients.
http://www.pepwave.com
48
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
DNS Proxy Settings
To enable the DNS proxy feature, check this box, and then set up the feature at
Network>LAN>DNS Proxy Settings. A DNS proxy server can be enabled to
serve DNS requests originating from LAN/PPTP/SpeedFusion TM peers. Requests
are forwarded to the DNS servers/resolvers defined for each WAN connection.
Enable
DNS Caching
This field is to enable DNS caching on the built-in DNS proxy server. When the
option is enabled, queried DNS replies will be cached until the records’ TTL has
been reached. This feature can help improve DNS lookup time. However, it
cannot return the most up-to-date result for those frequently updated DNS
records. By default, DNS Caching is disabled.
Include Google Public
DNS Servers
When this option is enabled, the DNS proxy server will also forward DNS
requests to Google's Public DNS Servers, in addition to the DNS servers defined
in each WAN. This could increase the DNS service's availability. This setting is
disabled by default.
Local DNS Records
This table is for defining custom local DNS records. A static local DNS record
consists of a host name and IP address. When looking up the host name from the
LAN to LAN IP of the Pepwave router, the corresponding IP address will be
returned. Press
DNS Resolvers
to create a new record. Press
to remove a record.
Check the box to enable the WINS server. A list of WINS clients will be displayed
at Network>LAN>DNS Proxy Settings>DNS Resolvers. This field specifies
which DNS resolvers will receive forwarded DNS requests. If no WAN/VPN/LAN
DNS resolver is selected, all of the WAN’s DNS resolvers will be selected.
If a SpeedFusionTM peer is selected, you may enter the VPN peer’s DNS resolver
IP address(es). Queries will be forwarded to the selected connections’ resolvers. If
all of the selected connections are down, queries will be forwarded to all resolvers
on healthy WAN connections.
- Advanced feature, please click the
button on the top right hand corner to activate.
Finally, if needed, configure Bonjour forwarding, Apple’s zero configuration networking
http://www.pepwave.com
49
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
protocol. Once VLAN configuration is complete, click Save to store your changes.
Bonjour Forwarding Settings
Enable
Bonjour
Service
Check this box to turn on Bonjour forwarding.
Choose Service and Client networks from the drop-down menus, and then click
add the networks. To delete an existing Bonjour listing, click
http://www.pepwave.com
50
to
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
To enable VLAN configuration, click the
button in the IP Settings section.
To add a new LAN, click the New LAN button. To change LAN settings, click the name
of the LAN to change under the LAN heading.
The following settings are displayed when creating a new LAN or editing an existing
LAN.
IP Settings
IP Address &
Subnet Mask
Enter the Pepwave router’s IP address and subnet mask values to be used on the LAN.
Network Settings
Name
VLAN ID
Inter-VLAN
routing
Captive Portal
Enter a name for the LAN.
Enter a number for your VLAN.
Check this box to enable routing between virtual LANs.
Check this box to turn on captive portals.
http://www.pepwave.com
51
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
DHCP Server Settings
DHCP Server
When this setting is enabled, the Pepwave router’s DHCP server automatically assigns an
IP address to each computer that is connected via LAN and configured to obtain an IP
address via DHCP. The Pepwave router’s DHCP server can prevent IP address collisions
on the LAN.
To enable DHCP bridge relay, please click the
IP Range &
Subnet Mask
icon on this menu item.
These settings allocate a range of IP address that will be assigned to LAN computers by the
Pepwave router’s DHCP server.
Lease Time
This setting specifies the length of time throughout which an IP address of a DHCP client
remains valid. Upon expiration of Lease Time, the assigned IP address will no longer be
valid and the IP address assignment must be renewed.
DNS Servers
This option allows you to input the DNS server addresses to be offered to DHCP clients. If
Assign DNS server automatically is selected, the Pepwave router’s built-in DNS server
address (i.e., LAN IP address) will be offered.
WINS Servers
BOOTP
Extended
DHCP Option
DHCP
Reservation
This option allows you to specify the Windows Internet Name Service (WINS) server. You
may choose to use the built-in WINS server or external WINS servers. When this unit is
connected using SpeedFusionTM, other VPN peers can share this unit's built-in WINS server
by entering this unit's LAN IP address in their DHCP WINS Servers setting. Therefore, all
PC clients in the VPN can resolve the NetBIOS names of other clients in remote peers. If
you have enabled this option, a list of WINS clients will be displayed at Status>WINS
Clients.
Check this box to enable BOOTP on older networks that still require it.
In addition to standard DHCP options (e.g. DNS server address, gateway address, subnet
mask), you can specify the value of additional extended DHCP options, as defined in RFC
2132. With these extended options enabled, you can pass additional configuration
information to LAN hosts. To define an extended DHCP option, click the Add button, choose
the option to define, and then enter its value. For values that are in IP address list format,
you can enter one IP address per line in the provided text area input control. Each option
can be defined once only.
This setting reserves the assignment of fixed IP addresses for a list of computers on the
LAN. The computers to be assigned fixed IP addresses on the LAN are identified by their
MAC addresses. The fixed IP address assignment is displayed as a cross-reference list
between the computers’ names, MAC addresses, and fixed IP addresses.
Name (an optional field) allows you to specify a name to represent the device. MAC
addresses should be in the format of 00:AA:BB:CC:DD:EE. Press
to create a new
record. Press
to remove a record. Reserved clients information can be imported from
the Client List, located at Status>Client List. For more details, please refer to Section
http://www.pepwave.com
52
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
22.3.
To configure DHCP relay, first click the
to display the settings.
button found next to the DHCP Server option
DHCP Relay Settings
Enable
Check this box to turn on DHCP relay. Click the
icon to disable DHCP relay.
DHCP Server IP
Address
Enter the IP addresses of one or two DHCP servers in the provided fields. The DHCP
servers entered here will receive relayed DHCP requests from the LAN. For active-passive
DHCP server configurations, enter active and passive DHCP server relay IP addresses in
DHCP Server 1 and DHCP Server 2.
DHCP Option
82
DCHP Option 82 includes device information as relay agent for the attached client when
forwarding DHCP requests from client to server. This option also embeds the device’s MAC
address and network name in circuit and remote IDs. Check this box to enable DHCP
Option 82.
Once DHCP is set up, configure LAN Physical Settings, Static Route Settings, WINS
Server Settings, and DNS Proxy Settings as noted above.
http://www.pepwave.com
53
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
9.2
Captive Portal
The captive portal serves as gateway that clients have to pass if they wish to access the
internet using your router. To configure, navigate to Network>LAN>Captive Portal.
Captive Portal Settings
Enable
Hostname
Access Mode
Check Enable and then, optionally, select the LANs/VLANs that will use the captive
portal.
To customize the portal’s form submission and redirection URL, enter a new URL in this
field. To reset the URL to factory settings, click Default.
Click Open Access to allow clients to freely access your router. Click User
Authentication to force your clients to authenticate before accessing your router.
This authenticates your clients through a RADIUS server. After selecting this option, you
will see the following fields:
RADIUS Server
Fill in the necessary information to complete your connection to the server and enable
authentication.
This authenticates your clients through a LDAP server. Upon selecting this option, you
will see the following fields:
LDAP Server
Fill in the necessary information to complete your connection to the server and enable
authentication.
http://www.pepwave.com
54
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Access
Quota
Quota Reset
Time
Allowed
Networks
Splash Page
Set a time and data cap to each user’s Internet usage.
This menu determines how your usage quota resets. Setting it to Daily will reset it at a
specified time every day. Setting a number of minutes after quota reached establish a
timer for each user that begins after the quota has been reached.
To whitelist a network, enter the domain name / IP address here and click
delete an existing network from the list of allowed networks, click the
to the listing.
. To
button next
Here, you can choose between using the Pepwave router’s built-in captive portal and
redirecting clients to a URL you define.
The Portal Customization menu has two options:
and
. Clicking
displays a pop-up previewing the captive portal that your clients will see. Clicking
displays the following menu:
http://www.pepwave.com
55
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Portal Customization
Logo
Image
Message
Terms &
Conditions
Custom
Landing
Page
Click the Choose File button to select a logo to use for the built-in portal.
If you have any additional messages for your users, enter them in this field.
If you would like to use your own set of terms and conditions, please enter them here. If
left empty, the built-in portal will display the default terms and conditions.
Fill in this field to redirect clients to an external URL.
10 Configuring the WAN Interface(s)
WAN Interface settings are located at Network>WAN. To reorder WAN priority, drag on
the appropriate WAN by holding the left mouse button, move it to the desired priority
(the first one would be the highest priority, the second one would be lower priority, and
so on), and drop it by releasing the mouse button.
To disable a particular WAN connection, drag on the appropriate WAN by holding the
left mouse button, move it the Disabled row, and drop it by releasing the mouse button.
You can also set priorities on the Dashboard. Click the Details button in the
corresponding row to modify the connection setting.
Important Note
Connection details will be changed and become effective immediately after clicking the Save and Apply button.
http://www.pepwave.com
56
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
10.1 Ethernet WAN
From Network>WAN, choose a WAN connection and then click Details.
WAN Port (Section 1)
WAN
Connection
Name
Schedule
Enter a name to represent this WAN connection.
Click the drop-down menu to apply a time schedule to this interface
There are three possible connection methods for Ethernet WAN:
Connection
Method



DHCP
Static IP
PPPoE
The connection method and details are determined by, and can be obtained from, the ISP.
See the following sections for details on each connection method.
Routing Mode
IP
Address/Subnet
Mask/Default
Gateway
This field shows that NAT (network address translation) will be applied to the traffic routed
over this WAN connection. IP Forwarding is available when you click the link in the help
text.
Enter the WAN IP address and subnet mask, as well as the IP address of the default
gateway, in these fields.
http://www.pepwave.com
57
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Hostname
DNS Servers
Enter a hostname for this WAN port if needed.
Select a DNS server for this port to use. This port can either be automatically selected or
manually designated.
WAN Port (Section 2)
Standby State
This setting specifies the standby state of the WAN connection. The available options are
Remain connected and Disconnect. The default state is Remain Connected.
Upstream
Bandwidth
This setting specifies the data bandwidth in the outbound direction from the LAN through the
WAN interface.
Downstream
Bandwidth
This setting specifies the data bandwidth in the inbound direction from the WAN interface to
the LAN. This value is referenced as the default weight value when using the algorithm
Least Used or the algorithm Persistence (Auto) in outbound policy with Managed by
Custom Rules chosen (see Section 15.2).
Health Check
Method
This setting specifies the health check method for the WAN connection. The value of method
can be configured as Disabled, Ping, DNS Lookup, or HTTP. The default method is
Disabled. See Section 10.4 for configuration details.
These fields are for specifying the target DNS servers where DNS lookups will be sent to for
health check.
PING Hosts
If the box Use first two DNS servers as Health Check DNS Servers is checked, the first two
DNS servers will be the DNS lookup targets for checking the connection healthiness. If the
box is not checked, the field Host 1 must be filled and the field Host 2 is optional.
The connection is considered to be up if DNS responses are received from any one of the
http://www.pepwave.com
58
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
health check DNS servers, regardless of whether the result is positive or negative.
Timeout
If a health check test cannot be completed within the specified amount of time, the test will
be treated as failed.
Health Check
Interval
This is the number of consecutive check failures before treating a connection as down.
Health Check
Retries
This is the number of consecutive check failures before treating a connection as down.
Recovery
Retries
This is the number of responses required after a health check failure before treating a
connection as up again.
WAN Port (Section 3)
This setting specifies the dynamic DNS service provider to be used for the WAN based on
supported dynamic DNS service providers:
Dynamic DNS
Service
Provider

changeip.com

dyndns.org

no-ip.org

tzo.com

DNS-O-Matic
Select Disabled to disable this feature. See Section 9.5 for configuration details.
Bandwidth
Allowance
Monitor
This option enables bandwidth usage monitoring on this WAN connection for each billing
cycle. When this setting is not enabled, each month’s bandwidth usage is tracked, but no
action will be taken.
Port Speed
This setting specifies port speed and duplex configurations of the WAN port. By default,
Auto is selected and the appropriate data speed is automatically detected by the Pepwave
router. In the event of negotiation issues, the port speed can be manually specified. You can
also choose whether or not to advertise the speed to the peer by selecting the Advertise
Speed checkbox.
MTU
This setting specifies the maximum transmission unit. By default, MTU is set to Custom
1440. You may adjust the MTU value by editing the text field. Click Default to restore the
http://www.pepwave.com
59
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
default MTU value. Select Auto and the appropriate MTU value will be automatically
detected. Auto-detection will run each time the WAN connection establishes.
WAN Port (Section 4)
MSS
This setting should be configured based on the maximum payload size that the local system
can handle. The MSS (maximum segment size) is computed from the MTU minus 40 bytes
for TCP over IPv4. If MTU is set to Auto, the MSS will also be set automatically. By default,
MSS is set to Auto.
MAC Address
Clone
Some service providers (e.g., cable providers) identify the client’s MAC address and require
the client to always use the same MAC address to connect to the network. In such cases,
change the WAN interface’s MAC address to the original client PC’s MAC address via this
field. The default MAC address is a unique value assigned at the factory. In most cases, the
default value is sufficient. Clicking Default restores the MAC address to the default value.
VLAN
Click the square if you wish to enable VLAN functionality and enable multiple broadcast
domains. Once you enable VLAN, you will be able to enter a name for your network.
Reply to ICMP
PING
If this field is disabled, the WAN connection will not respond to ICMP ping requests. By
default, this is enabled.
Additional
Public IP
Address
The IP Address list represents the list of fixed Internet IP addresses assigned by the ISP, in
the event that more than one Internet IP address is assigned to this WAN connection. Enter
the fixed Internet IP addresses and the corresponding subnet mask, and then click the
Down Arrow button to populate IP address entries to the IP Address List.
http://www.pepwave.com
60
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
IPv6
IPv6
IPv6 support can be enabled on one of the available Ethernet WAN ports. On this screen, you
can choose which WAN will support IPv6. To enable IPv6 support on a WAN, the WAN router
must respond to stateless address auto configuration advertisements and DHCPv6 requests.
IPv6 clients on the LAN will acquire their IPv6, gateway, and DNS server addresses from it.
The device will also acquire an IPv6 address for performing ping/traceroute checks and
accepting web admin accesses. Note: This feature is only available on the Pepwave MAX 700,
HD2, and HD2 IP67.
10.1.1 DHCP Connection
There are four possible connection methods:
1.
DHCP
2.
Static IP
3.
PPPoE
4.
L2TP
The DHCP connection method is suitable if the ISP provides an IP address
automatically using DHCP (e.g., satellite modem, WiMAX modem, cable, Metro
Ethernet, etc.).
DHCP Connection Settings
Routing Mode
NAT allows substituting the real address in a packet with a mapped address that is
routable on the destination network. By clicking the help icon in this field, you can
display the IP Forwarding option, if your network requires it.
http://www.pepwave.com
61
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
IP Address/
Subnet Mask/
Default Gateway
Hostname
(Optional)
DNS Servers
This information is obtained from the ISP automatically.
If your service provider's DHCP server requires you to supply a hostname value
upon acquiring an IP address, you may enter the value here. If your service
provider does not provide you with the value, you can safely bypass this option.
Each ISP may provide a set of DNS servers for DNS lookups. This setting
specifies the DNS (Domain Name System) servers to be used when a DNS lookup
is routed through this connection.
Selecting Obtain DNS server address automatically results in the DNS servers
being assigned by the WAN DHCP server to be used for outbound DNS lookups
over the connection. (The DNS servers are obtained along with the WAN IP
address assigned from the DHCP server.)
When Use the following DNS server address(es) is selected, you may enter
custom DNS server addresses for this WAN connection into the DNS Server 1
and DNS Server 2 fields.
10.1.2 Static IP Connection
The static IP connection method is suitable if your ISP provides a static IP address to
connect directly.
Static IP Settings
Routing Mode
NAT allows substituting the real address in a packet with a mapped address that is
routable on the destination network. By clicking the help icon in this field, you can display
the IP Forwarding option, if your network requires it.
IP Address /
Subnet Mask /
Default
Gateway
These settings allow you to specify the information required in order to communicate on
the Internet via a fixed Internet IP address. The information is typically determined by and
can be obtained from the ISP.
DNS Servers
Each ISP may provide a set of DNS servers for DNS lookups. This setting specifies the
DNS (Domain Name System) servers to be used when a DNS lookup is routed through
this connection. Selecting Obtain DNS server address automatically results in the DNS
servers being assigned by the WAN DHCP server to be used for outbound DNS lookups
over the connection. (The DNS servers are obtained along with the WAN IP address
assigned from the DHCP server.) When Use the following DNS server address(es) is
http://www.pepwave.com
62
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
selected, you may enter custom DNS server addresses for this WAN connection into the
DNS Server 1 and DNS Server 2 fields.
10.1.3 PPPoE Connection
This connection method is suitable if your ISP provides a login ID/password to connect
via PPPoE.
PPPoE Settings
Routing Mode
IP Address /
Subnet Mask /
Default Gateway
PPPoE User
Name / Password
Confirm PPPoE
Password
NAT allows substituting the real address in a packet with a mapped address that is
routable on the destination network. By clicking the help icon in this field, you can
display the IP Forwarding option, if your network requires it.
This information is obtained from the ISP automatically.
Enter the required information in these fields in order to connect via PPPoE to the ISP.
The parameter values are determined by and can be obtained from the ISP.
Verify your password by entering it again in this field.
Service Name
(Optional)
Service name is provided by the ISP.
Note: Leave this field blank unless it is provided by your ISP.
IP Address
(Optional)
If your ISP provides a PPPoE IP address, enter it here.
Note: Leave this field blank unless it is provided by your ISP.
DNS Servers
Each ISP may provide a set of DNS servers for DNS lookups. This setting specifies
the DNS (Domain Name System) servers to be used when a DNS lookup is routed
through this connection. Selecting Obtain DNS server address automatically results
http://www.pepwave.com
63
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
in the DNS servers being assigned by the WAN DHCP server to be used for outbound
DNS lookups over the connection. (The DNS servers are obtained along with the WAN
IP address assigned from the DHCP server.) When Use the following DNS server
address(es) is selected, you may enter custom DNS server addresses for this WAN
connection into the DNS Server 1 and DNS Server 2 fields.
10.1.4 L2TP Connection
L2TP has all the compatibility and convenience of PPTP with greater security. Combine
this with IPsec for a good balance between ease of use and security.
L2TP Settings
L2TP User
Name /
Password
Confirm L2TP
Password
Enter the required information in these fields in order to connect via L2TP to your ISP.
The parameter values are determined by and can be obtained from your ISP.
Verify your password by entering it again in this field.
Server IP
Address / Host
L2TP server address is a parameter which is provided by your ISP.
Note: Leave this field blank unless it is provided by your ISP.
Address Type
Your ISP will also indicate whether the server IP address is Dynamic or Static. Please click
the appropriate value.
Each ISP may provide a set of DNS servers for DNS lookups. This setting specifies the
DNS (Domain Name System) servers to be used when a DNS lookup is routed through this
connection.
DNS Servers
Selecting Obtain DNS server address automatically results in the DNS servers assigned
by the PPPoE server to be used for outbound DNS lookups over the WAN connection.
(The DNS servers are obtained along with the WAN IP address assigned from the PPPoE
server.)
http://www.pepwave.com
64
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
When Use the following DNS server address(es) is selected, you can enter custom DNS
server addresses for this WAN connection into the DNS server 1 and DNS server 2 fields.
10.2 Cellular WAN
To access cellular WAN settings, click Network>WAN>Details.
(Available on the Pepwave MAX BR1, HD2, and HD2 IP67 only)
Cellular Status
IMSI
This is the International Mobile Subscriber Identity which uniquely identifies the SIM card. This
is applicable to 3G modems only.
MEID
Some Pepwave routers support both HSPA and EV-DO. For Sprint or Verizon Wireless EV-DO
users, a unique MEID identifier code (in hexadecimal format) is used by the carrier to associate
the EV-DO device with the user. This information is presented in hex and decimal format.
ESN
This serves the same purpose as MEID HEX but uses an older format.
IMEI
This is the unique ID for identifying the modem in GSM/HSPA mode.
http://www.pepwave.com
65
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
WAN Connection Settings
WAN
Connection
Name
Schedule
Network Mode
Enter a name to represent this WAN connection.
Click the drop-down menu to apply a time schedule to this interface if needed.
Users have to specify the network they are on accordingly.
Auto: The subnet mask will be set automatically.
Subnet
Selection
Routing Mode
Force /31 Subnet: The subnet mask will be set as 255.255.255.254(/31), and the gateway IP
address will be recalculated.
This option allows you to select the routing method to be used in routing IP frames via the
WAN connection. The mode can be either NAT (network address translation) or IP
Forwarding. Click the
button to enable IP forwarding.
Each ISP may provide a set of DNS servers for DNS lookups. This setting specifies the
DNS (Domain Name System) servers to be used when a DNS lookup is routed through this
connection.
DNS Servers
Selecting Obtain DNS server address automatically results in the DNS servers assigned
by the PPPoE server to be used for outbound DNS lookups over the WAN connection.
(The DNS servers are obtained along with the WAN IP address assigned from the PPPoE
server.)
When Use the following DNS server address(es) is selected, you can enter custom DNS
server addresses for this WAN connection into the DNS server 1 and DNS server 2 fields.
http://www.pepwave.com
66
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Cellular Settings
Network
Selection
3G/2G
By default, the MAX router will automatically choose a network to connect to. If you wish to
use only certain networks, click the
button beside the menu item.
This drop-down menu allows restricting cellular to particular band. Click the
enable the selection of specific bands.
button to
Authentication
Choose from PAP Only or CHAP Only to use those authentication methods exclusively.
Select Auto to automatically choose an authentication method.
Data Roaming
This checkbox enables data roaming on this particular SIM card. Please check your service
provider’s data roaming policy before proceeding.
http://www.pepwave.com
67
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
This setting applies to 3G/EDGE/GPRS modems only. It does not apply to EVDO/EVDO Rev.
A modems. This allows you to configure the APN settings of your connection. If Auto is
selected, the mobile operator should be detected automatically. The connected device will be
configured and connection will be made automatically. If there is any difficulty in making
connection, you may select Custom to enter your carrier’s APN, Login, Password, and Dial
Number settings manually. The correct values can be obtained from your carrier. The default
and recommended setting is Auto.
Operator
Settings
APN / Login /
Password /
SIM PIN
When Auto is selected, the information in these fields will be filled automatically. Select
Custom to customize these parameters. The parameter values are determined by and can be
obtained from the ISP.
Bandwidth
Allowance
Monitor
Check the box Enable to enable bandwidth usage monitoring on this WAN connection for each
billing cycle. When this option is not enabled, bandwidth usage of each month is still being
tracked but no action will be taken.
Action
Start Day
Monthly
Allowance
If email notification is enabled, you will be notified by email when usage hits 75% and 95% of
the monthly allowance. If Disconnect when usage hits 100% of monthly allowance is
checked, this WAN connection will be disconnected automatically when the usage hits the
monthly allowance. It will not resume connection unless this option has been turned off or the
usage has been reset when a new billing cycle starts.
This option allows you to define which day of the month each billing cycle begins.
This field is for defining the maximum bandwidth usage allowed for the WAN connection each
month.
General Settings
Standby State
This option allows you to choose whether to remain connected or disconnected when this WAN
connection is no longer in the highest priority and has entered the standby state. When Remain
connected is chosen, bringing up this WAN connection to active makes it immediately available
for use.
Idle
Disconnect
When Internet traffic is not detected within the user-specified timeframe, the modem will
automatically disconnect. Once the traffic is resumed by the LAN host, the connection will be reactivated.
http://www.pepwave.com
68
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Health Check Settings
Heath Check
Method
Timeout
This setting allows you to specify the health check method for the cellular connection. Available
options are Disabled, Ping, DNS Lookup, HTTP, and SmartCheck. The default method is
DNS Lookup. See Section 10.4 for configuration details.
If a health check test cannot be completed within the specified amount of time, the test will be
treated as failed.
Health Check
Interval
This is the time interval between each health check test.
Health Check
Retries
This is the number of consecutive check failures before treating a connection as down.
Recovery
Retries
This is the number of responses required after a health check failure before treating a
connection as up again.
Dynamic DNS Settings
This setting specifies the dynamic DNS service provider to be used for the WAN based on
supported dynamic DNS service providers:
Dynamic DNS
Service
Provider

changeip.com

dyndns.org

no-ip.org

tzo.com

DNS-O-Matic
Select Disabled to disable this feature. See Section 9.5 for configuration details.
http://www.pepwave.com
69
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
10.3 Wi-Fi WAN
To access Wi-Fi WAN settings, click Network>WAN>Details.
Wi-Fi Connection Settings
WAN Connection
Name
Schedule
Standby State
Enter a name to represent this WAN connection.
Click the drop-down menu to apply a time schedule to this interface.
This setting specifies the state of the WAN connection while in standby. The available
options are Remain Connected (hot standby) and Disconnect (cold standby).
MTU
This setting specifies the maximum transmission unit. By default, MTU is set to Custom
1440. You may adjust the MTU value by editing the text field. Click Default to restore the
default MTU value. Select Auto and the appropriate MTU value will be automatically
detected. The auto-detection will run each time the WAN connection establishes
Reply to ICMP
PING
If this setting is disabled, the WAN connection will not respond to ICMP ping requests. By
default, this setting is enabled.
Wi-Fi WAN Settings
Channel
Selection
Determine whether the channel will be automatically selected. If you select custom, the
following table will appear:
http://www.pepwave.com
70
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Roaming
Connect to
Any Open
Mode AP
Checking this box will enable Wi-Fi roaming. Click the
icon for additional options.
This option is to specify whether the Wi-Fi WAN will connect to any open mode access
points it finds.
Bandwidth Allowance Monitor
If Error! Reference source not found. is enabled, you will be notified by email
when usage hits 75% and 95% of the monthly allowance.
Action
Start Day
Monthly
Allowance
If Disconnect when usage hits 100% of monthly allowance is checked, this WAN
connection will be disconnected automatically when the usage hits the monthly allowance.
It will not resume connection unless this option has been turned off or the usage has been
reset when a new billing cycle starts.
This option allows you to define which day of the month each billing cycle begins.
This field is for defining the maximum bandwidth usage allowed for the WAN connection
each month.
http://www.pepwave.com
71
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Health Check Settings
Method
This setting specifies the health check method for the WAN connection. This value can be
configured as Disabled, PING, DNS Lookup, or HTTP. The default method is DNS
Lookup. For mobile Internet connections, the value of Method can be configured as
Disabled or SmartCheck.
Health Check Disabled
When Disabled is chosen in the Method field, the WAN connection will always be considered as up. The
connection will NOT be treated as down in the event of IP routing errors.
Health Check Method: PING
ICMP ping packets will be issued to test the connectivity with a configurable target IP address or hostname. A WAN
connection is considered as up if ping responses are received from either one or both of the ping hosts.
PING Hosts
This setting specifies IP addresses or hostnames with which connectivity is to be tested via
ICMP ping. If Use first two DNS servers as Ping Hosts is checked, the target ping host
will be the first DNS server for the corresponding WAN connection. Reliable ping hosts with
a high uptime should be considered. By default, the first two DNS servers of the WAN
connection are used as the ping hosts.
Health Check Method: DNS Lookup
DNS lookups will be issued to test connectivity with target DNS servers. The connection will be treated as up if DNS
responses are received from one or both of the servers, regardless of whether the result was positive or negative.
http://www.pepwave.com
72
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Health Check
DNS Servers
This field allows you to specify two DNS hosts’ IP addresses with which connectivity is to be
tested via DNS Lookup.
If Use first two DNS servers as Health Check DNS Servers is checked, the first two DNS
servers will be the DNS lookup targets for checking a connection's health. If the box is not
checked, Host 1 must be filled, while a value for Host 2 is optional.
If Include public DNS servers is selected and no response is received from all specified
DNS servers, DNS lookups will also be issued to some public DNS servers. A WAN
connection will be treated as down only if there is also no response received from the public
DNS servers.
Connections will be considered as up if DNS responses are received from any one of the
health check DNS servers, regardless of a positive or negative result. By default, the first
two DNS servers of the WAN connection are used as the health check DNS servers.
Health Check Method: HTTP
HTTP connections will be issued to test connectivity with configurable URLs and strings to match.
URL1
WAN Settings>WAN Edit>Health Check Settings>URL1
The URL will be retrieved when performing an HTTP health check. When String to Match
is left blank, a health check will pass if the HTTP return code is between 200 and 299
(Note: HTTP redirection codes 301 or 302 are treated as failures). When String to Match is
filled, a health check will pass if the HTTP return code is between 200 and 299 and if the
HTTP response content contains the string.
URL 2
WAN Settings>WAN Edit>Health Check Settings>URL2
If URL2 is also provided, a health check will pass if either one of the tests passed.
http://www.pepwave.com
73
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Other Health Check Settings
Timeout
This setting specifies the timeout in seconds for ping/DNS lookup requests. The default
timeout is 5 seconds.
Health Check
Interval
This setting specifies the time interval in seconds between ping or DNS lookup requests.
The default health check interval is 5 seconds.
Health Check
Retries
This setting specifies the number of consecutive ping/DNS lookup timeouts after which the
Peplink Balance will treat the corresponding WAN connection as down. Default health
retries is set to 3. Using the default Health Retries setting of 3, the corresponding WAN
connection will be treated as down after three consecutive timeouts.
Recovery
Retries
This setting specifies the number of consecutive successful ping/DNS lookup responses
that must be received before the Peplink Balance treats a previously down WAN connection
as up again. By default, Recover Retries is set to 3. Using the default setting, a WAN
connection that is treated as down will be considered as up again upon receiving three
consecutive successful ping/DNS lookup responses.
Dynamic DNS Settings
This setting specifies the dynamic DNS service provider to be used for the WAN.
Supported providers are:
Service Provider

changeip.com

dyndns.org

no-ip.org

tzo.com

DNS-O-Matic
Select Disabled to disable this feature.
User ID / User /
Email
Password / Pass /
This setting specifies the registered user name for the dynamic DNS service.
This setting specifies the password for the dynamic DNS service.
http://www.pepwave.com
74
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
TZO Key
Update All Hosts
Hosts / Domain
Check this box to automatically update all hosts.
This setting specifies a list of hostnames or domains to be associated with the public
Internet IP address of the WAN connection.
Important Note
In order to use dynamic DNS services, appropriate hostname registration(s), as well as a valid account with a
supported dynamic DNS service provider, are required.
A dynamic DNS update is performed whenever a WAN’s IP address is changed, such as when an IP is changed
after a DHCP IP refresh or reconnection.
Due to dynamic DNS service providers’ policies, a dynamic DNS host expires automatically when the host record
has not been not updated for a long time. Therefore, the Peplink Balance performs an update every 23 days, even if
a WAN’s IP address did not change.
10.3.1 Creating Wi-Fi Connection Profiles
You can manually create a profile to connect to a Wi-Fi connection. This is useful for
creating a profile for connecting to hidden-SSID access points. Click
Network>WAN>Details>Create Profile… to get started.
This will open a window similar to the one shown below:
http://www.pepwave.com
75
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Wi-Fi Connection Profile Settings
Type
Network Name
(SSID)
Select whether the network will connect automatically or manually.
Enter a name to represent this Wi-Fi connection.
This option allows you to select which security policy is used for this wireless network.
Available options:

Open

WEP

WPA/WPA2 – Personal

WPA/WPA2 – Enterprise
Security
10.4 WAN Health Check
To ensure traffic is routed to healthy WAN connections only, the Pepwave router can
periodically check the health of each WAN connection. The health check settings for
each WAN connection can be independently configured via Network>WAN>Details.
Health Check Settings
Method
This setting specifies the health check method for the WAN connection. This value can be
configured as Disabled, PING, DNS Lookup, or HTTP. The default method is DNS
Lookup. For mobile Internet connections, the value of Method can be configured as
Disabled or SmartCheck.
Health Check Disabled
http://www.pepwave.com
76
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
When Disabled is chosen in the Method field, the WAN connection will always be considered as up. The
connection will NOT be treated as down in the event of IP routing errors.
Health Check Method: PING
ICMP ping packets will be issued to test the connectivity with a configurable target IP address or hostname. A WAN
connection is considered as up if ping responses are received from either one or both of the ping hosts.
PING Hosts
This setting specifies IP addresses or hostnames with which connectivity is to be tested via
ICMP ping. If Use first two DNS servers as Ping Hosts is checked, the target ping host
will be the first DNS server for the corresponding WAN connection. Reliable ping hosts with
a high uptime should be considered. By default, the first two DNS servers of the WAN
connection are used as the ping hosts.
Health Check Method: DNS Lookup
DNS lookups will be issued to test connectivity with target DNS servers. The connection will be treated as up if DNS
responses are received from one or both of the servers, regardless of whether the result was positive or negative.
Health Check
DNS Servers
This field allows you to specify two DNS hosts’ IP addresses with which connectivity is to be
tested via DNS lookup.
If Use first two DNS servers as Health Check DNS Servers is checked, the first two DNS
servers will be the DNS lookup targets for checking a connection's health. If the box is not
checked, Host 1 must be filled, while a value for Host 2 is optional.
If Include public DNS servers is selected and no response is received from all specified
DNS servers, DNS lookups will also be issued to some public DNS servers. A WAN
connection will be treated as down only if there is also no response received from the public
DNS servers.
Connections will be considered as up if DNS responses are received from any one of the
health check DNS servers, regardless of a positive or negative result. By default, the first
two DNS servers of the WAN connection are used as the health check DNS servers.
Health Check Method: HTTP
HTTP connections will be issued to test connectivity with configurable URLs and strings to match.
URL1
WAN Settings>WAN Edit>Health Check Settings>URL1
The URL will be retrieved when performing an HTTP health check. When String to Match
is left blank, a health check will pass if the HTTP return code is between 200 and 299
(Note: HTTP redirection codes 301 or 302 are treated as failures). When String to Match is
http://www.pepwave.com
77
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
filled, a health check will pass if the HTTP return code is between 200 and 299 and if the
HTTP response content contains the string.
WAN Settings>WAN Edit>Health Check Settings>URL2
If URL2 is also provided, a health check will pass if either one of the tests passed.
URL 2
Other Health Check Settings
Timeout
This setting specifies the timeout in seconds for ping/DNS lookup requests. The default
timeout is 5 seconds.
Health Check
Interval
This setting specifies the time interval in seconds between ping or DNS lookup requests.
The default health check interval is 5 seconds.
Health Check
Retries
This setting specifies the number of consecutive ping/DNS lookup timeouts after which the
Pepwave router will treat the corresponding WAN connection as down. Default health
retries is set to 3. Using the default Health Retries setting of 3, the corresponding WAN
connection will be treated as down after three consecutive timeouts.
Recovery
Retries
This setting specifies the number of consecutive successful ping/DNS lookup responses
that must be received before the Pepwave router treats a previously down WAN connection
as up again. By default, Recover Retries is set to 3. Using the default setting, a WAN
connection that is treated as down will be considered as up again upon receiving three
consecutive successful ping/DNS lookup responses.
Automatic Public DNS Server Check on DNS Test Failure
When the health check method is set to DNS Lookup and health checks fail, the Pepwave router will automatically
perform DNS lookups on public DNS servers. If the tests are successful, the WAN may not be down, but rather the
target DNS server malfunctioned. You will see the following warning message on the main page:
10.5 Dynamic DNS Settings
Pepwave routers are capable of registering the domain name relationships to dynamic
DNS service providers. Through registration with dynamic DNS service provider(s), the
default public Internet IP address of each WAN connection can be associated with a
host name. With dynamic DNS service enabled for a WAN connection, you can connect
to your WAN's IP address from the external, even if its IP address is dynamic. You must
register for an account from the listed dynamic DNS service providers before enabling
this option.
If the WAN connection's IP address is a reserved private IP address (i.e., behind a NAT
http://www.pepwave.com
78
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
router), the public IP of each WAN will be automatically reported to the DNS service
provider.
Either upon a change in IP addresses or every 23 days without link reconnection, the
Pepwave router will connect to the dynamic DNS service provider to perform an IP
address update within the provider’s records.
The settings for dynamic DNS service provider(s) and the association of hostname(s)
are configured via Network>WAN>Details>Dynamic DNS Service Provider/Dynamic
DNS Settings.
Dynamic DNS Settings
This setting specifies the dynamic DNS service provider to be used for the WAN based
on supported dynamic DNS service providers:
Dynamic DNS






changeip.com
dyndns.org
no-ip.org
tzo.com
DNS-O-Matic
Others…
Support custom Dynamic DNS servers by entering its URL. Works with
any service compatible with DynDNS API.
Select Disabled to disable this feature.
Account Name /
Email Address
This setting specifies the registered user name for the dynamic DNS service.
Password / TZO
Key
This setting specifies the password for the dynamic DNS service.
Hosts / Domain
This field allows you to specify a list of host names or domains to be associated with
the public Internet IP address of the WAN connection. If you need to enter more than
one host, use a carriage return to separate them.
Important Note
In order to use dynamic DNS services, appropriate host name registration(s) and a valid account with a supported
dynamic DNS service provider are required. A dynamic DNS update is performed whenever a WAN’s IP address
changes (e.g., the IP is changed after a DHCP IP refresh, reconnection, etc.). Due to dynamic DNS service
http://www.pepwave.com
79
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
providers’ policy, a dynamic DNS host will automatically expire if the host record has not been updated for a long
time. Therefore the Pepwave router performs an update every 23 days, even if a WAN’s IP address has not
changed.
http://www.pepwave.com
80
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
11 Advanced Wi-Fi Settings
Wi-Fi settings can be configured at Advanced>Wi-Fi Settings (or AP>Settings on
some models). Note that menus displayed can vary by model.
Wi-Fi Radio Settings
This drop-down menu specifies the national/regional regulations which the Wi-Fi radio
should follow.
Operating
Country

If a North American region is selected, RF channels 1 to 11 will be available
and the maximum transmission power will be 26 dBm (400 mW).

If European region is selected, RF channels 1 to 13 will be available. The
maximum transmission power will be 20 dBm (100 mW).
NOTE: Users are required to choose an option suitable to local laws and regulations.
Important Note
Per FCC regulation, the country selection is not available on all models marketed in
the US. All US models are fixed to US channels only.
Wi-Fi AP Settings
Protocol
This option allows you to specify whether 802.11b and/or 802.11g client association
requests will be accepted. Available options are 802.11ng and 802.11na. By default,
802.11ng is selected.
Channel
This option allows you to select which 802.11 RF channel will be utilized. Channel 1
(2.412 GHz) is selected by default.
Channel Width
Available options are 20 MHz, 40 MHz, and Auto (20/40 MHz) . Default is Auto (20/40
MHz), which allows both widths to be used simultaneously.
Output Power
This option is for specifying the transmission output power for the Wi-Fi AP. There are 4
relative power levels available – Max, High, Mid, and Low. The actual output power
will be bound by the regulatory limits of the selected country.
http://www.pepwave.com
81
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Advanced Wi-Fi AP settings can be displayed by clicking the
on the top right-hand
corner of the Wi-Fi AP Settings section, which can be found at AP>Settings. Other
models will display a separate section called Wi-Fi AP Advanced Settings, which can
be found at Advanced>Wi-Fi Settings.
Wi-Fi AP Advanced Settings
This option is for setting the transmit bit rate for sending a beacon. By default, 1Mbps is
selected.
Beacon Rate A
Beacon Interval
A This option is for setting the time interval between each beacon. By default, 100ms is
DTIM A
Slot Time A
This field allows you to set the frequency for the beacon to include delivery traffic
indication messages. The interval is measured in milliseconds. The default value is set to
1 ms.
This field is for specifying the unit wait time before transmitting a packet. By default, this
field is set to 9 µs.
ACK Timeout A
This field is for setting the wait time to receive an acknowledgement packet before
performing a retransmission. By default, this field is set to 48 µs.
Frame
Aggregation A
This option allows you to enable frame aggregation to increase transmission throughput.
Guard Interval A
selected.
This is where you opt for a short or long guard period interval for your transmissions.
- Advanced feature, please click the
http://www.pepwave.com
button on the top right-hand corner to activate.
82
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Wi-Fi WAN settings can be configured at Advanced>Wi-Fi Settings (or
Advanced>Wi-Fi WAN or some models).
Wi-Fi WAN Settings
Channel Width
Available options are 20/40 MHz and 20 MHz. Default is 20/40 MHz, which allows both
widths to be used simultaneously.
Bit Rate
This option allows you to select a specific bit rate for data transfer over the device’s WiFi network. By default, Auto is selected.
Output Power
This option is for specifying the transmission output power for the Wi-Fi AP. There are 4
relative power levels available – Max, High, Mid, and Low. The actual output power
will be bound by the regulatory limits of the selected country. Note that selecting the
Boost option may cause the MAX’s radio output to exceed local regulatory limits.
http://www.pepwave.com
83
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
12 MediaFast Configuration
MediaFast settings can be configured from the Network menu.
12.1 Setting Up MediaFast Content Caching
To access MediaFast content caching settings, select Advanced>Cache Control.
Cache Control Settings
Domain
Source IP
Subnet
Choose to Cache on all domains, or enter domain names and then choose either Cache
the specified domains only or Do not cache the specified domains.
This setting allows caching to be applied to the user-specified IP subnets. If "Any" is
selected, then caching will apply to all subnets.
Content Type
Check these boxes to cache the listed content types or leave boxes unchecked to disable
caching for the listed types.
Cache Lifetime
Settings
Enter a file extension, such as JPG or DOC. Then enter a lifetime in days to specify how
long files with that extension will be cached. Add or delete entries using the controls on the
right.
http://www.pepwave.com
84
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
12.2 Scheduling Content Prefetching
Content prefetching allows you to download content on a schedule that you define,
which can help to preserve network bandwidth during busy times and keep costs down.
To access MediaFast content prefetching settings, select Advanced >Prefetch
Schedule.
Prefetch Schedule Settings
Name
This field displays the name given to the scheduled download.
Status
Check the status of your scheduled download here.
Next Run
Time/Last Run
Time
These fields display the date and time of the next and most recent occurrences of the
scheduled download.
Last Duration
Check this field to ensure that the most recent download took as long as expected to
complete. A value that is too low might indicate an incomplete download or incorrectly
specified download target, while a value that is too long could mean a download with an
incorrectly specified target or stop time.
Result
Last Download
This field indicates whether downloads are in progress (
) or complete (
).
Check this field to ensure that the most recent download file size is within the expected
range. A value that is too low might indicate an incomplete download or incorrectly specified
download target, while a value that is too long could mean a download with an incorrectly
specified target or stop time. This field is also useful for quickly seeing which downloads are
consuming the most storage space.
http://www.pepwave.com
85
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
To begin a scheduled download immediately, click
Actions
To cancel a scheduled download, click
To edit a scheduled download, click
To delete a scheduled download, click
Click to begin creating a new scheduled download. Clicking the button will cause the
following screen to appear:
New Schedule
Simply provide the requested information to create your schedule.
Clear Web
Cache
Clear Statistics
To clear all cached content, click this button. Note that this action cannot be undone.
To clear all prefetch and status page statistics, click this button.
12.3 Viewing MediaFast Statistics
To get details on storage and bandwidth usage, select Status>MediaFast.
http://www.pepwave.com
86
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
http://www.pepwave.com
87
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
13
Bandwidth Bonding SpeedFusionTM / PepVPN
Pepwave bandwidth bonding SpeedFusionTM is our patented technology that enables
our SD-WAN routers to bond multiple Internet connections to increase site-to-site
bandwidth and reliability. SpeedFusion functionality securely connects your Pepwave
router
to
another
Pepwave
or
Peplink
device
(Peplink
Balance
210/310/380/580/710/1350 only). Data, voice, or video communications between these
locations are kept confidential across the public Internet.
Bandwidth bonding SpeedFusionTM is specifically designed for multi-WAN environments.
In case of failures and network congestion at one or more WANs, other WANs can be
used to continue carrying the network traffic.
Different models of our SD-WAN routers have different numbers of site-to-site
connections allowed. End-users who need to have more site-to-site connections can
purchase a SpeedFusion license to increase the number of site-to-site connections
allowed.
Pepwave routers can aggregate all WAN connections’ bandwidth for routing
SpeedFusionTM traffic. Unless all the WAN connections of one site are down, Pepwave
routers can keep the VPN up and running.
VPN bandwidth bonding is supported in Firmware 5.1 or above. All available bandwidth
will be utilized to establish the VPN tunnel, and all traffic will be load balanced at packet
level across all links. VPN bandwidth bonding is enabled by default.
http://www.pepwave.com
88
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
13.1 PepVPN
To configure PepVPN and SpeedFusion, navigate to Advanced>SpeedFusion™ or
Advanced>PepVPN.
The local LAN subnet and subnets behind the LAN (defined under Static Route on the
LAN settings page) will be advertised to the VPN. All VPN members (branch offices and
headquarters) will be able to route to local subnets.
Note that all LAN subnets and the subnets behind them must be unique. Otherwise,
VPN members will not be able to access each other.
All data can be routed over the VPN using the 256-bit AES encryption standard. To
configure, navigate to Advanced>SpeedFusion™ or Advanced>PepVPN and click
the New Profile button to create a new VPN profile (you may have to first save the
displayed default profile in order to acesss the New Profile button). Each profile
specifies the settings for making VPN connection with one remote Pepwave or Peplink
device. Note that available settings vary by model.
http://www.pepwave.com
89
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
A list of defined SpeedFusion connection profiles and a Link Failure Detection Time
option will be shown. Click the New Profile button to create a new VPN connection
profile for making a VPN connection to a remote Peplink Balance via the available WAN
connections. Each profile is for making a VPN connection with one remote Peplink
Balance.
PepVPN Profile Settings
Name
This field is for specifying a name to represent this profile. The name can be any
combination of alphanumeric characters (0-9, A-Z, a-z), underscores (_), dashes (-), and/or
non-leading/trailing spaces ( ).
Active
When this box is checked, this VPN connection profile will be enabled. Otherwise, it will be
disabled.
Encryption
By default, VPN traffic is encrypted with 256-bit AES. If Off is selected on both sides of a
VPN connection, no encryption will be applied.
Authentication
Remote ID /
Pre-shared Key
Select from By Remote ID Only, Preshared Key, or X.509 to specify the method the
Peplink Balance will use to authenticate peers. When selecting By Remote ID Only, be
sure to enter a unique peer ID number in the Remote ID field.
This optional field becomes available when Remote ID / Pre-shared Key is selected as the
Peplink Balance’s VPN Authentication method, as explained above. Pre-shared Key
defines the pre-shared key used for this particular VPN connection. The VPN connection's
session key will be further protected by the pre-shared key. The connection will be up only if
the pre-shared keys on each side match. When the peer is running firmware 5.0+, this
setting will be ignored.
http://www.pepwave.com
90
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Enter Remote IDs either by typing out each Remote ID and Pre-shared Key, or by pasting a
CSV. If you wish to paste a CSV, click the
setting.
Remote
ID/Remote
Certificate
Allow Shared
Remote ID
NAT Mode
Remote IP
Address / Host
Names
(Optional)
Data Port
Bandwidth
Limit
Cost
icon next to the “Remote ID / Preshared Key”
These optional fields become available when X.509 is selected as the Peplink Balance’s
VPN authentication method, as explained above. To authenticate VPN connections using
X.509 certificates, copy and paste certificate details into these fields. To get more
information on a listed X.509 certificate, click the Show Details link below the field.
When this option is enabled, the router will allow multiple peers to run using the same
remote ID.
Check this box to allow the local DHCP server to assign an IP address to the remote peer.
When NAT Mode is enabled, all remote traffic over the VPN will be tagged with the
assigned IP address using network address translation.
If NAT Mode is not enabled, you can enter a remote peer’s WAN IP address or
hostname(s) here. If the remote uses more than one address, enter only one of them here.
Multiple hostnames are allowed and can be separated by a space character or carriage
return. Dynamic-DNS host names are also accepted.
This field is optional. With this field filled, the Peplink Balance will initiate connection to each
of the remote IP addresses until it succeeds in making a connection. If the field is empty,
the Peplink Balance will wait for connection from the remote peer. Therefore, at least one of
the two VPN peers must specify this value. Otherwise, VPN connections cannot be
established.
This field is used to specify a UDP port number for transporting outgoing VPN data. If
Default is selected, UDP port 4500 will be used. Port 32015 will be used if the remote unit
uses Firmware prior to version 5.4 or if port 4500 is unavailable. If Custom is selected,
enter an outgoing port number from 1 to 65535.
Define maximum download and upload speed to each individual peer. This functionality
requires the peer to use PepVPN version 4.0.0 or above.
Define path cost for this profile.
OSPF will determine the best route through the network using the assigned cost.
Default: 10
WAN
SmoothingA
Select the degree to which WAN Smoothing will be implemented across your WAN links.
- Advanced feature, please click the
button on the top right-hand corner to activate.
To enable Layer 2 Bridging between PepVPN profiles, navigate to
Network>LAN>Basic Settings>*LAN Profile Name* and refer to instructions in
section 9.1
http://www.pepwave.com
91
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
8.41
WAN Connection Priority
WAN
Connection
Priority
If your device supports it, you can specify the priority of WAN connections to be used for
making VPN connections. WAN connections set to OFF will never be used. Only available
WAN connections with the highest priority will be used.
To enable asymmetric connections, connection mapping to remote WANs, cut-off latency,
and packet loss suspension time, click the
button.
Send All Traffic To
This feature allows you to redirect all traffic to a specified PepVPN connection. Click the
connection and the following menu will appear:
button to select your
You could also specify a DNS server to resolve incoming DNS requests. Click the checkbox next to Backup Site to
designate a backup SpeedFusion profile that will take over, should the main PepVPN connection fail.
Outbound Policy/PepVPN Outbound Custom Rules
Some models allow you to set outbound policy and custom outbound rules from Advanced>PepVPN. See Section
14 for more information on outbound policy settings.
http://www.pepwave.com
92
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
PepVPN Local ID
The local ID is a text string to identify this local unit when establishing a VPN connection. When creating a profile on
a remote unit, this local ID must be entered in the remote unit's Remote ID field. Click the
ID.
icon to edit Local
PepVPN Settings
Handshake
PortA
To designate a custom handshake port (TCP), click the custom radio button and enter the
port number you wish to designate.
Backward
Compatibility
Determine the level of backward compatibility needed for PepVPN tunnels. The use of the
Latest setting is recommended as it will improve the performance and resilience of
SpeedFusion connections.
Link Failure
Detection Time
The bonded VPN can detect routing failures on the path between two sites over each WAN
connection. Failed WAN connections will not be used to route VPN traffic. Health check
packets are sent to the remote unit to detect any failure. The more frequently checks are
sent, the shorter the detection time, although more bandwidth will be consumed.
When Recommended (default) is selected, a health check packet is sent every five
seconds, and the expected detection time is 15 seconds.
When Fast is selected, a health check packet is sent every three seconds, and the
expected detection time is six seconds.
When Faster is selected, a health check packet is sent every second, and the expected
detection time is two seconds.
When Extreme is selected, a health check packet is sent every 0.1 second, and the
expected detection time is less than one second.
- Advanced feature, please click the
button on the top right-hand corner to activate.
Important Note
Peplink proprietary SpeedFusionTM uses TCP port 32015 and UDP port 4500 for establishing VPN connections. If
you have a firewall in front of your Pepwave devices, you will need to add firewall rules for these ports and protocols
to allow inbound and outbound traffic to pass through the firewall.
http://www.pepwave.com
93
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Tip
Want to know more about VPN sub-second session failover? Visit our YouTube Channel for a video tutorial!
http://youtu.be/TLQgdpPSY88
http://www.pepwave.com
94
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
13.2 The Pepwave Router Behind a NAT Router
Pepwave routers support establishing SpeedFusion TM over WAN connections which are
behind a NAT (network address translation) router.
To enable a WAN connection behind a NAT router to accept VPN connections, you can
configure the NAT router in front of the WAN connection to inbound port-forward TCP
port 32015 to the Pepwave router.
If one or more WAN connections on Unit A can accept VPN connections (by means of
port forwarding or not), while none of the WAN connections on the peer Unit B can do
so, you should enter all of Unit A’s public IP addresses or hostnames into Unit B’s
Remote IP Addresses / Host Names field. Leave the field in Unit A blank. With this
setting, a SpeedFusionTM connection can be set up and all WAN connections on both
sides will be utilized.
See the following diagram for an example of this setup in use:
One of the WANs connected to Router A is non-NAT’d (212.1.1.1). The rest of the
WANs connected to Router A and all WANs connected to Router B are NAT’d. In this
case, the Peer IP Addresses / Host Names field for Router B should be filled with all of
Router A’s hostnames or public IP addresses (i.e., 212.1.1.1, 212.2.2.2, and 212.3.3.3),
and the field in Router A can be left blank. The two NAT routers on WAN1 and WAN3
connected to Router A should inbound port-forward TCP port 32015 to Router A so that
all WANs will be utilized in establishing the VPN.
http://www.pepwave.com
95
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
13.3 SpeedFusionTM Status
SpeedFusionTM status is shown in the Dashboard. The connection status of each
connection profile is shown as below.
After clicking the Status button at the top right corner of the SpeedFusion TM table, you
will be forwarded to Status>SpeedFusionTM, where you can view subnet and WAN
connection information for each VPN peer. Please refer to Section 22.6 for details.
IP Subnets Must Be Unique Among VPN Peers
The entire interconnected SpeedFusionTM network is a single non-NAT IP network. Avoid duplicating subnets in
your sites to prevent connectivity problems when accessing those subnets.
http://www.pepwave.com
96
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
14 IPsec VPN
IPsec VPN functionality securely connects one or more branch offices to your
company's main headquarters or to other branches. Data, voice, and video
communications between these locations are kept safe and confidential across the
public Internet.
IPsec VPN on Pepwave routers is specially designed for multi-WAN environments. For
instance, if a user sets up multiple IPsec profiles for a multi-WAN environment and
WAN1 is connected and healthy, IPsec traffic will go through this link. However, should
unforeseen problems (e.g., unplugged cables or ISP problems) cause WAN1 to go
down, our IPsec implementation will make use of WAN2 and WAN3 for failover.
14.1 IPsec VPN Settings
Many Pepwave products can make multiple IPsec VPN connections with Peplink,
Pepwave, Cisco, and Juniper routers. Note that all LAN subnets and the subnets behind
them must be unique. Otherwise, VPN members will not be able to access each other.
All data can be routed over the VPN with a selection of encryption standards, such as
3DES, AES-128, and AES-256. To configure IPsec VPN on Pepwave devices that
support it, navigate to Advanced>IPsec VPN.
A NAT-Traversal option and list of defined IPsec VPN profiles will be shown. NATTraversal should be enabled if your system is behind a NAT router. Click the New
Profile button to create new IPsec VPN profiles that make VPN connections to remote
Pepwave, Cisco, or Juniper routers via available WAN connections. To edit any of the
profiles, click on its associated connection name in the leftmost column.
http://www.pepwave.com
97
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
IPsec VPN Settings
Name
This field is for specifying a local name to represent this connection profile.
Active
When this box is checked, this IPsec VPN connection profile will be enabled. Otherwise, it
http://www.pepwave.com
98
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
will be disabled.
Connect Upon
Disconnection
of
Remote
Gateway IP
Address /
Host Name
Check this box and select a WAN to connect to this VPN automatically when the specified
WAN is disconnected.
Enter the remote peer’s public IP address. For Aggressive Mode, this is optional.
Enter the local LAN subnets here. If you have defined static routes, they will be shown
here.
Using NAT, you can map a specific local network / IP address to another, and the packets
received by remote gateway will appear to be coming from the mapped network / IP
address. This allow you to establish IPsec connection to a remote site that has one or
more subnets overlapped with local site.
Two types of NAT policies can be defined:
Local
Networks
One-to-One NAT policy: if the defined subnet in Local Network and NAT Network has the
same size, for example, policy "192.168.50.0/24 > 172.16.1.0/24" will translate the local
IP address 192.168.50.10 to 172.16.1.10 and 192.168.50.20 to 172.16.1.20. This is a
bidirectional mapping which means clients in remote site can initiate connection to the
local clients using the mapped address too.
Many-to-One NAT policy: if the defined NAT Network on the right hand side is an IP
address (or having a network prefix /32), for example, policy "192.168.1.0/24 >
172.168.50.1/32" will translate all clients in 192.168.1.0/24 network to 172.168.50.1. This
is a unidirectional mapping which means clients in remote site will not be able to initiate
connection to the local clients.
Remote
Networks
Authentication
Mode
Force UDP
Encapsulation
Enter the LAN and subnets that are located at the remote site here.
To access your VPN, clients will need to authenticate by your choice of methods. Choose
between the Preshared Key and X.509 Certificate methods of authentication.
Choose Main Mode if both IPsec peers use static IP addresses. Choose Aggressive
Mode if one of the IPsec peers uses dynamic IP addresses.
For forced UDP encapsulation regardless of NAT-traversal, tick this checkbox.
Pre-shared
Key
This defines the peer authentication pre-shared key used to authenticate this VPN
connection. The connection will be up only if the pre-shared keys on each side match.
Remote
Certificate
(pem
encoded)
Available only when X.509 Certificate is chosen as the Authentication method, this field
allows you to paste a valid X.509 certificate.
Local ID
In Main Mode, this field can be left blank. In Aggressive Mode, if Remote Gateway IP
Address is filled on this end and the peer end, this field can be left blank. Otherwise, this
http://www.pepwave.com
99
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
field is typically a U-FQDN.
Remote ID
In Main Mode, this field can be left blank. In Aggressive Mode, if Remote Gateway IP
Address is filled on this end and the peer end, this field can be left blank. Otherwise, this
field is typically a U-FQDN.
Phase 1 (IKE)
Proposal
In Main Mode, this allows setting up to six encryption standards, in descending order of
priority, to be used in initial connection key negotiations. In Aggressive Mode, only one
selection is permitted.
Phase 1 DH
Group
This is the Diffie-Hellman group used within IKE. This allows two parties to establish a
shared secret over an insecure communications channel. The larger the group number,
the higher the security.
Group 2: 1024-bit is the default value.
Group 5: 1536-bit is the alternative option.
Phase 1 SA
Lifetime
This setting specifies the lifetime limit of this Phase 1 Security Association. By default, it is
set at 3600 seconds.
Phase 2 (ESP)
Proposal
In Main Mode, this allows setting up to six encryption standards, in descending order of
priority, to be used for the IP data that is being transferred. In Aggressive Mode, only
one selection is permitted.
Phase 2 PFS
Group
Perfect forward secrecy (PFS) ensures that if a key was compromised, the attacker will be
able to access only the data protected by that key.
None - Do not request for PFS when initiating connection. However, since there is no
valid reason to refuse PFS, the system will allow the connection to use PFS if requested
by the remote peer. This is the default value.
Group 2: 1024-bit Diffie-Hellman group. The larger the group number, the higher the
security.
Group 5: 1536-bit is the third option.
Phase 2 SA
Lifetime
This setting specifies the lifetime limit of this Phase 2 Security Association. By default, it is
set at 28800 seconds.
WAN Connection Priority
WAN Connection
Select the appropriate WAN connection from the drop-down menu.
http://www.pepwave.com
100
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
15 Outbound Policy Management
Pepwave routers can flexibly manage and load balance outbound traffic among WAN
connections.
Important Note
Outbound policy is applied only when more than one WAN connection is active .
The settings for managing and load balancing outbound traffic are located at
Advanced>Outbound Policy or Advanced>PepVPN, depending on the model.
15.1 Outbound Policy
Outbound policies for managing and load balancing outbound traffic are located at
Network>Outbound Policy>
or Advanced>PepVPN>Outbound Policy.
There are three main selections for the outbound traffic policy:
 High Application Compatibility
 Normal Application Compatibility
 Custom
Note that some Pepwave routers provide only the Send All Traffic To setting here. See
Section 12.1 for details.
Outbound Policy Settings
High
Outbound traffic from a source LAN device is routed through the same WAN connection
regardless of the destination Internet IP address and protocol. This option provides the
http://www.pepwave.com
101
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Application
Compatibility
highest application compatibility.
Normal
Application
Compatibility
Outbound traffic from a source LAN device to the same destination Internet IP address will
be routed through the same WAN connection persistently, regardless of protocol. This
option provides high compatibility to most applications, and users still benefit from WAN link
load balancing when multiple Internet servers are accessed.
Custom
Outbound traffic behavior can be managed by defining rules in a custom rule table. A
default rule can be defined for connections that cannot be matched with any of the rules.
The default policy is Normal Application Compatibility.
Tip
Want to know more about creating outbound rules? Visit our YouTube Channel for a video tutorial!
http://youtu.be/rKH4AS_bQnE
15.2 Custom Rules for Outbound Policy
Click
in the Outbound Policy form. Choose Custom and press the Save button.
http://www.pepwave.com
102
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
The bottom-most rule is Default. Edit this rule to change the device’s default manner of
controlling outbound traffic for all connections that do not match any of the rules above
it. Under the Service heading, click Default to change these settings.
To rearrange the priority of outbound rules, drag and drop them into the desired
sequence.
By default, Auto is selected as the Default Rule. You can select Custom to change the
algorithm to be used. Please refer to the upcoming sections for the details on the
available algorithms.
To create a custom rule, click Add Rule at the bottom of the table. Note that some
Pepwave routers display this button at Advanced>PepVPN>PepVPN Outbound
Custom Rules.
http://www.pepwave.com
103
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
New Custom Rule Settings
Service Name
Enable
This setting specifies the name of the outbound traffic rule.
This setting specifies whether the outbound traffic rule takes effect. When Enable is
checked, the rule takes effect: traffic is matched and actions are taken by the Pepwave
router based on the other parameters of the rule. When Enable is unchecked, the rule does
not take effect: the Pepwave router disregards the other parameters of the rule.
Click the drop-down menu next to the checkbox to apply a time schedule to this custom
rule.
Source
This setting specifies the source IP address, IP network, or MAC address for traffic that
matches the rule.
This setting specifies the destination IP address, IP network, or domain name for traffic that
matches the rule.
Destination
If Domain Name is chosen and a domain name, such as foobar.com, is entered, any
outgoing accesses to foobar.com and *.foobar.com will match this criterion. You may enter
a wildcard (.*) at the end of a domain name to match any host with a name having the
domain name in the middle. If you enter foobar.*, for example, www.foobar.com,
www.foobar.co.jp, or foobar.co.uk will also match. Placing wildcards in any other position is
not supported.
NOTE: if a server has one Internet IP address and multiple server names, and if one of the
names is defined here, accesses to any one of the server names will also match this rule.
http://www.pepwave.com
104
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Protocol and Port
This setting specifies the IP protocol and port of traffic that matches this rule.
This setting specifies the behavior of the Pepwave router for the custom rule.
One of the following values can be selected (note that some Pepwave routers provide only
some of these options):
Algorithm

Weighted Balance

Persistence

Enforced

Priority

Overflow

Least Used

Lowest Latency
The upcoming sections detail the listed algorithms.
Terminate
Sessions on Link
Recovery
This setting specifies whether to terminate existing IP sessions on a less preferred WAN
connection in the event that a more preferred WAN connection is recovered. This setting is
applicable to the Weighted, Persistence, and Priority algorithms. By default, this setting is
disabled. In this case, existing IP sessions will not be terminated or affected when any other
WAN connection is recovered. When this setting is enabled, existing IP sessions may be
terminated when another WAN connection is recovered, such that only the preferred
healthy WAN connection(s) is used at any point in time.
http://www.pepwave.com
105
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
15.2.1 Algorithm: Weighted Balance
This setting specifies the ratio of WAN connection usage to be applied on the specified
IP protocol and port. This setting is applicable only when Algorithm is set to Weighted
Balance.
The amount of matching traffic that is distributed to a WAN connection is proportional to
the weight of the WAN connection relative to the total weight. Use the sliders to change
each WAN’s weight.
For example, with the following weight settings:

Ethernet WAN1: 10

Ethernet WAN2: 10

Wi-Fi WAN: 10

Cellular 1: 10

Cellular 2: 10

USB: 10
Total weight is 60 = (10 +10 + 10 + 10 + 10 + 10).
Matching traffic distributed to Ethernet WAN1 is 16.7% = (10 / 60 x 100%.
Matching traffic distributed to Ethernet WAN2 is 16.7% = (10 / 60) x 100%.
Matching traffic distributed to Wi-Fi WAN is 16.7% = (10 / 60) x 100%.
Matching traffic distributed to Cellular 1 is 16.7% = (10 / 60) x 100%.
Matching traffic distributed to Cellular 2 is 16.7% = (10 / 60) x 100%.
Matching traffic distributed to USB is 16.7% = (10 / 60) x 100%.
http://www.pepwave.com
106
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
15.2.2 Algorithm: Persistence
The configuration of persistent services is the solution to the few situations where link
load distribution for Internet services is undesirable. For example, for security reasons,
many e-banking and other secure websites terminate the session when the client
computer’s Internet IP address changes mid-session.
In general, different Internet IP addresses represent different computers. The security
concern is that an IP address change during a session may be the result of an
unauthorized intrusion attempt. Therefore, to prevent damages from the potential
intrusion, the session is terminated upon the detection of an IP address change.
Pepwave routers can be configured to distribute data traffic across multiple WAN
connections. Also, the Internet IP depends on the WAN connections over which
communication actually takes place. As a result, a LAN client computer behind the
Pepwave router may communicate using multiple Internet IP addresses. For example, a
LAN client computer behind a Pepwave router with three WAN connections may
communicate on the Internet using three different IP addresses.
With the persistence feature, rules can be configured to enable client computers to
persistently utilize the same WAN connections for e-banking and other secure websites.
As a result, a client computer will communicate using one IP address, eliminating the
issues mentioned above.
There are two persistent modes: By Source and By Destination.
By Source:
By Destination:
The same WAN connection will be used for traffic matching the rule and originating from
the same machine, regardless of its destination. This option will provide the highest level
of application compatibility.
The same WAN connection will be used for traffic matching the rule, originating from the
same machine, and going to the same destination. This option can better distribute loads
to WAN connections when there are only a few client machines.
The default mode is By Source. When there are multiple client requests, they can be
distributed (persistently) to WAN connections with a weight. If you choose Auto in Load
Distribution, the weights will be automatically adjusted according to each WAN’s
Downstream Bandwidth which is specified in the WAN settings page). If you choose
Custom, you can customize the weight of each WAN manually by using the sliders.
http://www.pepwave.com
107
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
15.2.3 Algorithm: Enforced
This setting specifies the WAN connection usage to be applied on the specified IP
protocol and port. This setting is applicable only when Algorithm is set to Enforced.
Matching traffic will be routed through the specified WAN connection, regardless of the
health check status of the WAN connection. Starting from Firmware 5.2, outbound traffic
can be enforced to go through a specified SpeedFusion TM connection.
15.2.4 Algorithm: Priority
This setting specifies the priority of the WAN connections used to route the specified
network service. The highest priority WAN connection available will always be used for
routing the specified type of traffic. A lower priority WAN connection will be used only
when all higher priority connections have become unavailable.
Starting from Firmware 5.2, outbound traffic can be prioritized to go through
SpeedFusionTM connection(s). By default, VPN connections are not included in the
priority list.
Tip
Configure multiple distribution rules to accommodate different kinds of services.
15.2.5 Algorithm: Overflow
The traffic matching this rule will be routed through the healthy WAN connection that
has the highest priority and is not in full load. When this connection gets saturated, new
sessions will be routed to the next healthy WAN connection that is not in full load.
http://www.pepwave.com
108
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Drag and drop to specify the order of WAN connections to be used for routing traffic.
Only the highest priority healthy connection that is not in full load will be used.
15.2.6 Algorithm: Least Used
The traffic matching this rule will be routed through the healthy WAN connection that is
selected in Connection and has the most available download bandwidth. The available
download bandwidth of a WAN connection is calculated from the total download
bandwidth specified on the WAN settings page and the current download usage. The
available bandwidth and WAN selection is determined every time an IP session is
made.
15.2.7 Algorithm: Lowest Latency
The traffic matching this rule will be routed through the healthy WAN connection that is
selected in Connection and has the lowest latency. Latency checking packets are
issued periodically to a nearby router of each WAN connection to determine its latency
value. The latency of a WAN is the packet round trip time of the WAN connection.
Additional network usage may be incurred as a result.
Tip
The roundtrip time of a 6M down/640k uplink can be higher than that of a 2M down/2M up link because the overall
round trip time is lengthened by its slower upload bandwidth, despite its higher downlink speed. Therefore, this
algorithm is good for two scenarios:

All WAN connections are symmetric; or
http://www.pepwave.com
109
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual

A latency sensitive application must be routed through the lowest latency WAN, regardless of the WAN’s
available bandwidth.
15.2.8 Expert Mode
Expert Mode is available on some Pepwave routers for use
by advanced users. To enable the feature, click on the help
icon and click turn on Expert Mode.
In Expert Mode, a new special rule, SpeedFusionTM
Routes, is displayed in the Custom Rules table. This rule
represents all SpeedFusionTM routes learned from remote
VPN peers. By default, this bar is on the top of all custom
rules. This position means that traffic for remote VPN
subnets will be routed to the corresponding VPN peer. You
can create custom Priority or Enforced rules and move them
above the bar to override the SpeedFusionTM routes.
Upon disabling Expert Mode, all rules above the bar will be removed.
http://www.pepwave.com
110
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
16 Inbound Access
16.1 Port Forwarding Service
Pepwave routers can act as a firewall that blocks, by default, all inbound access from
the Internet. By using port forwarding, Internet users can access servers behind the
Pepwave router. Inbound port forwarding rules can be defined at Advanced>Port
Forwarding.
To define a new service, click Add Service.
Port Forwarding Settings
Enable
This setting specifies whether the inbound service takes effect. When Enable is checked, the
inbound service takes effect: traffic is matched and actions are taken by the Pepwave router
based on the other parameters of the rule. When this setting is disabled, the inbound service
does not take effect: the Pepwave router disregards the other parameters of the rule.
Service
Name
This setting identifies the service to the system administrator. Valid values for this setting
consist of only alphanumeric and underscore “_” characters.
IP Protocol
The IP Protocol setting, along with the Port setting, specifies the protocol of the service as
TCP, UDP, ICMP, or IP. Traffic that is received by the Pepwave router via the specified protocol
at the specified port(s) is forwarded to the LAN hosts specified by the Servers setting. Please
see below for details on the Port and Servers settings. Alternatively, the Protocol Selection
Tool drop-down menu can be used to automatically fill in the protocol and a single port number
of common Internet services (e.g. HTTP, HTTPS, etc.). After selecting an item from the
Protocol Selection Tool drop-down menu, the protocol and port number remain manually
modifiable.
http://www.pepwave.com
111
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
The Port setting specifies the port(s) that correspond to the service, and can be configured to
behave in one of the following manners:
Any Port, Single Port, Port Range, Port Map, and Range Mapping
Any Port: all traffic that is received by the Pepwave router via the specified protocol is
forwarded to the servers specified by the Servers setting. For example, with IP Protocol set to
TCP, and Port set to Any Port, all TCP traffic is forwarded to the configured servers.
Single Port: traffic that is received by the Pepwave router via the specified protocol at the
specified port is forwarded via the same port to the servers specified by the Servers setting.
For example, with IP Protocol set to TCP, and Port set to Single Port and Service Port 80,
TCP traffic received on port 80 is forwarded to the configured servers via port 80.
Port
Port Range: traffic that is received by the Pepwave router via the specified protocol at the
specified port range is forwarded via the same respective ports to the LAN hosts specified by
the Servers setting. For example, with IP Protocol set to TCP, and Port set to Port Range and
Service Ports 80-88, TCP traffic received on ports 80 through 88 is forwarded to the configured
servers via the respective ports.
Port Mapping: traffic that is received by Pepwave router via the specified protocol at the
specified port is forwarded via a different port to the servers specified by the Servers setting.
For example, with IP Protocol set to TCP, and Port set to Port Mapping, Service Port 80, and
Map to Port 88, TCP traffic on port 80 is forwarded to the configured servers via port 88.
(Please see below for details on the Servers setting.)
Range Mapping: traffic that is received by the Pepwave router via the specified protocol at the
specified port range is forwarded via a different port to the servers specified by the Servers
setting.
Inbound IP
Address(es)
Server IP
Address
This setting specifies the WAN connections and Internet IP address(es) from which the service
can be accessed.
This setting specifies the LAN IP address of the server that handles the requests for the
service.
http://www.pepwave.com
112
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
16.1.1 UPnP / NAT-PMP Settings
UPnP and NAT-PMP are network protocols which allow a computer connected to the
LAN port to automatically configure the router to allow parties on the WAN port to
connect to itself. That way, the process of inbound port forwarding becomes
automated.
When a computer creates a rule using these protocols, the specified TCP/UDP port of
all WAN connections' default IP address will be forwarded.
Check the corresponding box(es) to enable UPnP and/or NAT-PMP. Enable these
features only if you trust the computers connected to the LAN ports.
When the options are enabled, a table listing all the forwarded ports under these two
protocols can be found at Status>UPnP / NAT-PMP.
http://www.pepwave.com
113
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
17 NAT Mappings
NAT mappings allow IP address mapping of all inbound and outbound NAT’dt raffic to
and from an internal client IP address. Settings to configure NAT mappings are located
at Advanced>NAT Mappings.
To add a rule for NAT mappings, click Add NAT Rule.
NAT Mapping Settings
LAN
Client(s)
NAT mapping rules can be defined for a single LAN IP Address, an IP Range, or an IP
Network.
Address
This refers to the LAN host’s private IP address. The system maps this address to a
number of public IP addresses (specified below) in order to facilitate inbound and
outbound traffic. This option is only available when IP Address is selected.
Range
The IP range is a contiguous group of private IP addresses used by the LAN host. The
system maps these addresses to a number of public IP addresses (specified below) to
facilitate outbound traffic. This option is only available when IP Range is selected.
Network
The IP network refers to all private IP addresses and ranges managed by the LAN host.
The system maps these addresses to a number of public IP addresses (specified below)
to facilitate outbound traffic. This option is only available when IP Network is selected.
http://www.pepwave.com
114
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Inbound
Mappings
Outbound
Mappings
This setting specifies the WAN connections and corresponding WAN-specific Internet IP
addresses on which the system should bind. Any access to the specified WAN
connection(s) and IP address(es) will be forwarded to the LAN host. This option is only
available when IP Address is selected in the LAN Client(s) field.
Note that inbound mapping is not needed for WAN connections in drop-in mode or IP
forwarding mode. Also note that each WAN IP address can be associated to one NAT
mapping only.
This setting specifies the WAN IP addresses that should be used when an IP connection
is made from a LAN host to the Internet. Each LAN host in an IP range or IP network will
be evenly mapped to one of each selected WAN's IP addresses (for better IP address
utilization) in a persistent manner (for better application compatibility).
Note that if you do not want to use a specific WAN for outgoing accesses, you should still
choose default here, then customize the outbound access rule in the Outbound Policy
section. Also note that WAN connections in drop-in mode or IP forwarding mode are not
shown here.
Click Save to save the settings when configuration has been completed.
Important Note
Inbound firewall rules override the Inbound Mappings settings.
http://www.pepwave.com
115
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
18 QoS
18.1 User Groups
LAN and PPTP clients can be categorized into three user groups: Manager, Staff, and
Guest. This menu allows you to define rules and assign client IP addresses or subnets
to a user group. You can apply different bandwidth and traffic prioritization policies on
each user group in the Bandwidth Control and Application sections (note that the
options available here vary by model).
The table is automatically sorted by rule precedence. The smaller and more specific
subnets are put towards the top of the table and have higher precedence; larger and
less specific subnets are placed towards the bottom.
Click the Add button to define clients and their user group. Click the
button to
remove the defined rule. Two default rules are pre-defined and put at the bottom. They
are All DHCP reservation clients and Everyone, and they cannot be removed. The
All DHCP reservation client represents the LAN clients defined in the DHCP
Reservation table on the LAN settings page. Everyone represents all clients that are
not defined in any rule above. Click on a rule to change its group.
Add / Edit User Group
Subnet / IP
Address
From the drop-down menu, choose whether you are going to define the client(s) by
an IP Address or a Subnet. If IP Address is selected, enter a name defined in DHCP
reservation table or a LAN client's IP address. If Subnet is selected, enter a subnet
address and specify its subnet mask.
Group
This field is to define which User Group the specified subnet / IP address belongs to.
Once users have been assigned to a user group, their internet traffic will be restricted by
rules defined for that particular group. Please refer to the following two sections for
details.
http://www.pepwave.com
116
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
18.2 Bandwidth Control
You can define a maximum download speed (over all WAN connections) and upload
speed (for each WAN connection) that each individual Staff and Guest member can
consume. No limit can be imposed on individual Manager members. By default,
download and upload bandwidth limits are set to unlimited (set as 0).
18.3 Application
18.3.1 Application Prioritization
On many Pepwave routers, you can choose whether to apply the same prioritization
settings to all user groups or customize the settings for each group.
Three application priority levels can be set: ↑High,━ Normal, and↓Low. Pepwave
routers can detect various application traffic types by inspecting the packet content.
Select an application by choosing a supported application, or by defining a custom
application manually. The priority preference of supported applications is placed at the
top of the table. Custom applications are at the bottom.
http://www.pepwave.com
117
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
18.3.2 Prioritization for Custom Applications
Click the Add button to define a custom application. Click the button
column to delete the custom application in the corresponding row.
in the Action
When Supported Applications is selected, the Pepwave router will inspect network
traffic and prioritize the selected applications. Alternatively, you can select Custom
Applications and define the application by providing the protocol, scope, port number,
and DSCP value.
18.3.3 DSL/Cable Optimization
DSL/cable-based WAN connections have lower upload bandwidth and higher
download bandwidth. When a DSL/cable circuit's uplink is congested,
the download bandwidth will be affected. Users will not be able to download data at full
speed until the uplink becomes less congested. DSL/Cable Optimization can relieve
such an issue. When it is enabled, the download speed will become less affected by the
upload traffic. By default, this feature is enabled.
http://www.pepwave.com
118
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
19 Firewall
A firewall is a mechanism that selectively filters data traffic between the WAN side (the
Internet) and the LAN side of the network. It can protect the local network from potential
hacker attacks, access to offensive websites, and/or other inappropriate uses.
The firewall functionality of Pepwave routers supports the selective filtering of data
traffic in both directions:


Outbound (LAN to WAN)
Inbound (WAN to LAN)
The firewall also supports the following functionality:
 Intrusion detection and DoS prevention
 Web blocking
With SpeedFusionTM enabled, the firewall rules also apply to VPN tunneled traffic.
19.1 Outbound and Inbound Firewall Rules
19.1.1 Access Rules
The outbound firewall settings are located at Advanced>Firewall>Access
Rules>Outbound Firewall Rules.
http://www.pepwave.com
119
Copyright @ 2017 Pepwave
Pepwave MAX and Surf User Manual
Click Add Rule to display the following screen:
Inbound firewall settings are located at Advanced>Firewall>Access Rules>Inbound
Firewall Rules.
Click Add Rule to display the following screen:
Rules are matched from top to bottom. If a connection matches any one of the upper
rules, the matching process will stop. If none of the rules match, the Default rule will be
applied. By default, the Default rule is set as Allow for both outbound and inbound
access.
http://www.pepwave.com
120
Copyright @ 2017 Pepwave

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2017:09:18 20:56:09+08:00
Modify Date                     : 2017:09:19 17:55:27+08:00
Metadata Date                   : 2017:09:19 17:55:27+08:00
Format                          : application/pdf
Creator                         : victorchu
Title                           : Microsoft Word - MAX_BR1_MK2_UserManual_Rev1_Sep18_2017_PIsmo_Labs_Technology_Ltd_170918_2032p
Producer                        : Microsoft: Print To PDF
Document ID                     : uuid:6b1e89d0-c54d-40f0-923b-f4d0e350f454
Instance ID                     : uuid:0359b7d4-a139-4cf5-bc87-98d0c9bb2719
Has XFA                         : No
Page Count                      : 120
Author                          : victorchu

EXIF Metadata provided by EXIF.tools