Pismolabs Technology SURF400DX PepWave Surf400-DX User Manual PePWave Surf Series
Pismo Labs Technology Limited PepWave Surf400-DX PePWave Surf Series
Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 843327 |
| Application ID | wFf68RomTDAM3LJRuJnwPA== |
| Document Description | Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 157.25kB (1965611 bits) |
| Date Submitted | 2007-09-14 00:00:00 |
| Date Available | 2007-09-14 00:00:00 |
| Creation Date | 2007-09-03 08:22:44 |
| Producing Software | PrimoPDF |
| Document Lastmod | 2007-09-07 12:07:27 |
| Document Title | PePWave Surf Series User Manual |
| Document Creator | PrimoPDF http://www.primopdf.com |
| Document Author: | PePWave |
PePWave Surf Series PePWave Surf Indoor Series: Surf 200, AP 200, AP 400 PePWave Surf Outdoor Series: Surf AP 200/400-X, PolePoint 400-X, Surf 400-DX User Manual Document Rev. 1.2 September 07 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. Copyright © 2007 PePWave Ltd. All Rights Reserved. PePWave and the PePWave logo are trademarks of PePWave Ltd. Other brands or products mentioned may be trademarks or registered trademarks of their respective owners. PePWave Surf Series User Manual Table of Contents COPYRIGHT ..................................................................................................................................... 3 DISCLAIMER..................................................................................................................................... 3 PRODUCT DESCRIPTION ................................................................................................................. 4 3.1 3.2 3.3 FEATURES .....................................................................................................................................4 HARDWARE SETUP ........................................................................................................................5 LED DESCRIPTION ........................................................................................................................5 USING THE PEPWAVE SURF ............................................................................................................. 7 4.1 4.2 4.3 4.4 4.5 4.6 FIRST TIME SETUP ...........................................................................................................................8 SETTINGS DETAILS .......................................................................................................................11 INTEGRATED WI-FI ACCESS POINT CONFIGURATION ....................................................................13 TEST THE SETUP ............................................................................................................................20 FIRMWARE UPGRADE .................................................................................................................21 RESTORE TO DEFAULT SETTINGS ....................................................................................................21 APPENDIX: FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT ............................................... 22 Page 2 PePWave Surf Series User Manual Copyright Copyright © 2007 by PePWave Ltd. The content of this documentation may not be reproduced in any part or as a whole without the prior written permission of PePWave Ltd. Disclaimer PePWave does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any license under its patent right nor the patent rights of others. PePWave further reserves the right to make changes in any products described herein without notice. This documentation is subject to change without notice. Page 3 PePWave Surf Series User Manual Product Description PePWave Surf is a feature-rich Wi-Fi CPE with WPA, WPA2 and 802.1x supplicant support. It is designed to act as a Wireless router and connects LAN users with a Wireless Broadband Internet Service (such as Citywide Wi-Fi). It associates to a service provider and authenticates using 802.1x (if needed) on start up. Upon successful association and authentication, it will acquire an IP address from the service provider using DHCP. A DHCP server is built-in on its LAN port. Network Address Translation is performed for all outbound connections. Thus it supports multiple terminals to access the Internet simultaneously. 3.1 Features 10/100 Ethernet interface with auto-crossover detection Reset button for restoring settings to factory defaults Signal strength LED for showing the current signal strength (PePWave indoor serials only) WPA/WPA2-Personal and WPA/WPA2-Enterprise support Network Address Translation (NAT) routing Built-in DHCP server Inbound port range forwarding Integrated Wi-Fi Access Point (Surf AP indoor and outdoor only) Surf 200, AP 200, AP 400 Surf AP 200/400-X, PolePoint 400-X Page 4 Surf 400-DX PePWave Surf Series User Manual 3.2 Hardware Setup 3.2.1 Surf Indoor Series 1. Attach the provided antenna to the left most antenna connector 2. Connect the LAN port to the computer’s Ethernet port with an Ethernet cable. 3. Connect the end of the included power adapter to the power socket (labeled “DC 5V”) on PePWave Surf. 4. Power on the power adaptor. 3.2.1 Surf Outdoor Series Please follow the installation guide to set up AP 200/400-X, PolePoint 400-X, Surf 400-DX 3.3 LED Description 3.3.1 Surf Indoor Series LED Power Status LAN Color Green Status Description On Power is on Off Power is off Green Solid Received signal is Excellent, Very Good and Good Green Blinking Received signal is Low Amber Blinking Received signal is Very Low Amber Solid No wireless signal is detected Off Booting up / Upgrading firmware Green On Ethernet is connected Green Blinking Sending/Receiving data Off Ethernet is not connected Page 5 PePWave Surf Series User Manual LED Wi-Fi Signal Bars Color Status Description Green On Associated with an access point Green Blinking Sending/Receiving data Off Not associated with any access point N/A The number of lit signal bars depends on the strength of the received signal. A larger number of lit signal bars indicate stronger signals. Green 3.3.2 Surf DX Series LED Description LED PWR LAN Wi-Fi Color Green Green Green Status Description On Power is on Off Power is off On Ethernet is connected Off Ethernet is not connected On Associated with an access point. The number of LED lights from “MIN” to “MAX” indicates the received signal strength level. Off Not associated with any access point Page 6 PePWave Surf Series User Manual Using the PePWave Surf You should set up your computer’s LAN interface to obtain an IP address automatically. If you do so, you should have set it up correctly. In order to do so, select the “Start” menu, “Control Panel” and then “Network Connections”. Right click on the “Local Area Connection” icon, choose “Properties”, double-click on the item “Internet Protocol (TCP/IP)” from the list. On the screen, just set it as follows: Click the “OK” button to confirm the change. Page 7 PePWave Surf Series User Manual 4.1 First Time Setup On your PC, start a web browser, e.g. Internet Explorer, Mozilla Firefox, etc. Visit an Internet web site. If you are not associated to an access point, you should be redirected to a logon page. Or you can go also go to this URL http://192.168.20.1/ The page will look like this. Page 8 PePWave Surf Series User Manual Click the “Advanced Config” button to enter the parameters of the access point to associate to. You should see this screen: In the field “SSID” under Wireless Settings, input the access point’s SSID (sometimes it is called the “network name”). According to the setting of the Access Point you are associating to, you may choose a different “Authentication setting”. If “Static WEP key” or “WPA/WPA2-Personal” is selected for Authentication, input the Encryption Key field as well. (There are also options of “802.1x with dynamic WEP key” and “WPA/WPA2-Enterprise”. You do not need to use these settings unless instructed to do so by your ISP.) Click the “Save” button at the bottom to complete. You can now click the “Connect” link on the top bar and then click the “Connect” button to associate with the access point. Page 9 PePWave Surf Series User Manual At this point, you are associated with the access point. You may now close the web browser and open a new one to start web browsing. Page 10 PePWave Surf Series User Manual 4.2 Settings Details LAN Interface: To configure the LAN interface’s IP address and subnet mask. DHCP Server: To configure and enable the built-in DHCP server or not. If enabled, the IP address range can be configured. Wireless Settings: SSID: To configure the SSID / ESSID / Network Name of the wireless network to associate to. Radio Mode: It allows the user to choose between radio modulations support. E.g. 802.11b/g, 802.11g only, 802.11b, etc. The available settings depend on the Wi-Fi module installed on the device. Bit Rate: To fix the 802.11 transmit bit rate. Available options depend on the Radio Mode chosen. If “auto” is chosen, the device will choose the best bit rate dynamically and automatically. Authentication: Available options are Open, Static WEP Key, 802.1x with dynamic WEP key, WPA/WPA2-Enterprise and WPA/WPA2-Personal. The selection should be according to the setting of the access point you are associating to. Data transferred are encrypted under all modes except in Open mode. When Static WEP Key or WPA/WPA2-Personal is chosen, you should enter an encryption key in the Encryption Key field. (You do not need to use 802.1x and WPA/WPA2-Enterprise unless instructed to do so by your ISP.) Preferred AP: The MAC address of a preferred access point can be entered here. When the preferred access point is found and its signal strength is higher than the “Min Signal Strength”, it will connect to this preferred access point, no matter the other access points are found even they have higher signal strength or the same SSID. Page 11 PePWave Surf Series User Manual IP Settings: The IP address can be obtained automatically or configured manually. If you choose to manually configure the IP address for your unit, enter the fields “IP Address”, “Subnet Mask”, “Default Gateway”, “Preferred DNS Server” and “Alternate DNS Server”. MTU Size: You may also set the MTU Size to increase the data packet size your Surf can handle at one time. AP Settings: These settings apply only to the PePWave Surf AP model, and configure the properties of the Integrated Wi-Fi Access Point. The AP Settings will be covered in detail in the subsequent section Integrated Wi-Fi Access Point Configuration. WAI redirection: If the device is not connected to an access point, and the user is accessing an Internet web site, the settings control whether to redirect the web access to the web admin interface page or not. If this is disabled and the device is not connected, the browser will show a web access error message. The user can still access the web admin interface by accessing to the device’s LAN IP address. By default, the LAN IP address is set as http://192.168.20.1 . Web Password Protection: Sets the password to protect the web user interface. Restore default settings: To restore the device to default settings. When this option is clicked, default settings will be restored and the unit will be restarted. Reboot: To restart the device. Page 12 PePWave Surf Series User Manual 4.3 Integrated Wi-Fi Access Point Configuration Integrated Wi-Fi Access Point is configured via the CPE Setup tab. The following sections will provide information as a guide through the configuration. This session is not applicable for PePWave Surf DX series. 4.3.1 Available Access Point Settings The available Access Point (AP) settings for the Integrated Wi-Fi Access Point functionality are as follows: Disable Integrated Home Wi-Fi Access Point functionality is disabled Configure Manually Manual configuration of the SSID, Authentication, and Encryption Key values corresponding to the Access Point. Configure Automatically The SSID, Authentication, and Encryption Key values corresponding to the Access Point are automatically configured to be the same as the respective values that correspond to Citywide Wi-Fi. Page 13 PePWave Surf Series User Manual 4.3.2 Access Point Disabled Access Point Disabled, as shown with the red marker box Page 14 PePWave Surf Series User Manual 4.3.3 Manual Access Point configuration Manual Access Point Configuration, as shown with the red marker box Page 15 PePWave Surf Series User Manual In Manual Configuration mode, the SSID is manually entered. Authentication can be one of three configurable values: Open For Open Authentication Mode, no Encryption Key is necessary. Static WEP Key For Static WEP Key Authentication Mode, a 64- or 128-bit Encryption Key is required, and can be entered in either an ASCII or HEX representation. Static WEP Key Authentication Configuration WPA/WPA2-Personal For WPA/WPA2-Personal Authentication Mode, an Encryption Key, of at least 8 characters, is required. WPA/WPA2-Personal Authentication Configuration Broadcast SSID can be one of two configurable values: Enable The configured SSID will be broadcast such that it can be detected by an SSID scan. Disable The configured SSID will not be broadcast such that it cannot be detected by an SSID scan. In order to connect with the access point, the SSID needs to be known by the client. Page 16 PePWave Surf Series User Manual A.1.1 Automatic Access Point Configuration Auto. Access Point Configuration, as shown with the red marker box With the Access Point Configuration set to Configure Automatically, the SSID, Authentication, and Encryption Key values of the Integrated Home Wi-Fi Access Point will be configured to be the same as in the Wireless Settings section. This configuration mode is effectively equivalent to directly connecting 802.1b/g devices on the customers’ premises with Citywide Wi-Fi. Page 17 PePWave Surf Series User Manual Important Note: In the Wireless Settings section, if Authentication is set to either 802.1x with dynamic WEP key or WPA/WPA2-Enterprise, then the Configure Automatically option of the Access Point Configuration becomes unavailable, because the Integrated Home Wi-Fi Access Point functionality currently does not support authentication via the 802.1x with dynamic WEP key and WPA/WPA2-Enterprise methods. Automatic Access Point Configuration is unavailable with 802.1 with Dynamic WEP Key Authentication Page 18 PePWave Surf Series User Manual Automatic Access Point Configuration is unavailable with WPA/WPA1-Enterprise Authentication Page 19 PePWave Surf Series User Manual 4.4 Test the Setup To test to setup, you can now go to the PePWave Surf’s Main page, enter the user name and password. The realm (the text box next to the “@” sign) value can be left empty. Then click the Connect button. After connected, you should see: Page 20 PePWave Surf Series User Manual 4.5 Firmware Upgrade The PePWave Surf is able to check whether a newer firmware (the software running on the PePWave Surf) is available. This can be done in the Firmware Upgrade section. However, it is recommended that you do not update the firmware unless specifically instructed by your ISP to do so. When a firmware upgrade is needed, your ISP will either give you instructions or upgrade the firmware remotely. 4.6 Restore to Default Settings 4.6.1 Surf Indoor Series There are two ways to restore the PePWave Surf to default settings. If you are able to access the web admin interface, go to the “CPE Setup” page, and click the “Restore and Reboot” button. Otherwise, you can also power up the unit and wait for about 1 min. Then press the Reset button at the rear side of the unit using a pin and then hold it for 5 seconds. The unit will restore the settings to factory default and reboot. 4.6.2 Surf DX Series There are two ways to restore the PePWave Surf DX to default settings. If you are able to access the web admin interface, go to the “CPE Setup” page, and click the “Restore and Reboot” button. Otherwise, you can also power up the Surf DX unit and wait for about 1 min. Then push the Reset button at the bottom side of the unit and then hold it for 5 seconds. The unit will restore the settings to factory default and reboot. Page 21 PePWave Surf Series User Manual Appendix: Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4) Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Page 22 PePWave Surf Series User Manual SUPPORT Email: support@pepwave.com SALES Email: sales@pepwave.com BUSINESS DEVELOPMENT AND PARTNERS Email: partners@pepwave.com CORPORATE ADDRESS & PHONE www.pepwave.com US Address: PePWave Ltd. 800 West El Camino Real Mountain View CA 94040 United States Tel: Fax: +1-650-331-0641 +1-866-625-4664 Hong Kong Address: PePWave Ltd. 17/F, Park Building 476 Castle Peak Road Cheung Sha Wan Hong Kong Tel: Fax: +852-2786-9228 +852-3007-0588 h t t p : / / w w w . p e p w a v e . c o m Copyright © 2007 PePWave Ltd. All Rights Reserved.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Encryption : Standard V2.3 (128-bit) User Access : Print, Copy, Extract, Print high-res XMP Toolkit : 3.1-701 About : 59404f4d-5c52-11dc-0000-90a827d3375d Producer : PrimoPDF Modify Date : 2007:09:07 12:07:27+08:00 Create Date : 2007:09:03 08:22:44Z Creator Tool : PrimoPDF http://www.primopdf.com Metadata Date : 2007:09:07 12:07:27+08:00 Document ID : 59404f4d-5c52-11dc-0000-90a827d3375d Instance ID : uuid:87aa2af5-5be5-4361-834b-744457949324 Format : application/pdf Title : PePWave Surf Series User Manual Creator : PePWave Description : PePWave Surf Series User Manual Page Count : 23 Subject : PePWave Surf Series User Manual Author : PePWaveEXIF Metadata provided by EXIF.tools