Pixel Enterprise EXPERT-402TX Expert User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1638968
Application ID	uFVMZO71MYSdcBjt+y9Y2g==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	59.76kB (747015 bits)
Date Submitted	2012-02-17 00:00:00
Date Available	2012-02-20 00:00:00
Creation Date	2011-10-12 02:45:37
Producing Software	Corel PDF Engine Version 3.0.0.667
Document Lastmod	2011-10-12 02:45:37
Document Title	LV-W2英文文说明书 2011.5.18
Document Creator	CorelDRAW
Document Author:	chenlh

Wireless Live View Remote Control
无线图像可视快门线
261008 V10.01
Contents
Overview
Cautions before use
Features of Expert
Included items
Name of each part
Usage
Battery Installation
Turn power ON and OFF
Sync Code-Matching
Channel adjustment
Holding Expert Transmitter
Connect with the camera
Switching Signal Source
Enlarge and review
Sleep/Wake-up mode
03
04
07
08
09
12
12
13
14
15
16
17
18
19
20
Contents
LCD Brightness adjustment
Volume adjustment
Menu
Remote Shooting
PIXEL Expert Specifications
Overview
20
20
21
23
24
Thank you very much for purchasing PIXEL high-performance product
First of all, thank you for purchasing PIXEL's Expert. This is monitoring the lens view
or the CMOS view on transmitter. Receiver side supports single shooting, [BULB]
shooting and delay shooting. The transmitter supports audio and video inputs, and
CMOS camera lens; the receiver supports audio and video outputs to TV.
Please read this manual and make sure fully understand before using the product. With
this manual, you will easily handle the operation method and the attentive things.
This manual is current update of 1st May, 2011. Please contact to
PIXEL distributor for further information, if interesting of the
combining usage with products released after this day.
Cautions before use
Make sure the camera and Expert are powered off before install device.
As this is an electronic product accessory; some of the environment causes may affect the
working. However this is hardly ever to get this situation.
When connected the remote cable with the device, do not pull the wires.
This product can't be strong vibration, or may lead to product failure.
For a long time non-use, please turned off the view transmitter and the receiver's power and
remove the battery.
Do not put it in high temperature, such as a closed car under direct sunlight, the control panel
and other high-temperature areas.
Keep dry, do not use wet hand contact with the product, the product must not be immersed in
water or exposed to rain, and this may lead to not work properly.
Do not use flammable gases in violation of this warning may cause an explosion or fire.
Because this product include battery, regarding how to use and charge battery, please operate it
strictly according to related rules, otherwise may cause explosion, fire or physical injury.
Cautions before use
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
Cautions before use
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Features of Expert
ISM 2.4GHz frequency channel which qualified CE or FCC standard.
Operating range up to 200M
Real-time monitoring surround environment view from CMOS or camera lens directly
Support single, BULB and delay shooting.
3.5inch TFT screen; resolution of 320 x 240; 10 levels LCD back light brightness adjustments;
sleep mode setting.
Wide choices of power: rechargeable batteries, alkaline batteries, carbon batteries, etc.
Strong compatibility: suitable for different cameras with different connector.
Screen shots function: save display images in receiver for reference; and available for re-view.
Enlarge movement: support enlarges under COMS live-view mode and four-direction moving.
Video output: video and audio output to TV.
Included items
Name of each part
Please check all included items after open the packing, and PIXEL Expert with the following items:
Expert Transmitter
Expert Transmitter
1 Code matching button
2 Power socket
1 pc
Expert Receiver
1pc
Instruction Manual
1 pc
Shutter connecting cable
Video Connecting Cable
Canon
or
Nikon
2 pc
3 pc
2 pc
11
5 6 7
3 Power switch
4 Hot shoe locknut
12
5 Power LED indicator
10
13
6 Status LED indicator
7 Shooting LED indicator
8 Video/Audio signal input
9 Shooting output socket
10 USB socket
FC C ID :X5 SE XP ERT-4 02 TX
Optional Accessories
1 2 3 4
A/V Connecting Cable
11 Antenna
12 CMOS Lens
13 Channel switch
Name of each part
Name of each part
Expert Receiver
12
8 OK
14
9 Screen brightness increase/right shift button
11 Screen brightness reduce/left shift button
14 USB Socket
10
13
AV/Audio
10
11
12 Power switch
MENU Button
CMOS and camera view button
Video enlarge/Review button
Channel switch/sleep and
wake-up button
Status LED indicator
Shutter
Volume up/Up shift button
DC0
DC2
E3
2 Camera connecting side
A side
ST
Video Connecting Cable
10 Volume down/Down shift button
13 Audio output/AV signal output
N3
VC
EG
Shutter connecting cable
B side
A/V input plug 4
DC
11
Usage
Usage
Battery Installation
1. Slide and open battery hatch.
Transmitter uses 4 AA batteries; available to use rechargeable or
alkaline battery.
2. Install the battery according to the signs on the battery hatch.
When using 1.2V 2400mA battery, standby for 100 hours, working
time over 10 hours.
When the battery is low, POWER LED INDICATOR would flash as red.
The battery should be replaced or recharged immediately.
12
Turn power ON and OFF
Transmitter and receiver both have a power switch. Move it to ［
move it to ［ ］ turn off.
］ turn on;
Expert Transmitter:
When power on, the POWER LED continuously bright as red. When the power
supply voltage is not able to maintain equipment working, the POWER LED would
flash quickly.
Expert Transmitter Expert Receiver:
When turn on the power, the STATUS LED shows the receiver is on; the STATUS
LED off after starting up, and the screen shows [PIXEL Expert] and begins to
search signal of transmitter; LCD screen shows the image after received the signal.
* If fail to search out signals under the same channel, the screen would shows
[Disconnected], until it gets the same channel.
* If fail to search out signals under the same channel, switch receiver channel to
Expert Receiver
search other channels signal.
* When the power supply voltage is not able to maintain equipment working, the screen would shows
image of power low, and then the STATUS LED would quickly flash red.
13
Usage
Sync Code-Matching
1. Press [MENU] enters to the menu.
2. Press the right or left button move to [SYNC] page.
3. Press the up or down button move to [YES].
4. Press [OK], the STATUS LED flash as red, the screen shows [Syncing…], and then receiver gets
into Sync Code-Matching.
5. Press and hold [Code] on transmitter for two sec, the STATUS LED flash red, and the transmitter
gets into Sync Code-Matching.
6. Finishing Sync Code-Matching, the STATUS LED of transmitter and receiver off to exit the Sync
Code-Matching status. If transmitter and receiver are in the same channel, receiver would receive
images sent by transmitter.
* If transmitter and receiver fail to sync code with each other within 15 sec, both will exit Sync CodeMatching.
* Products without code-matching are originally under no code state, can receive signals regardless
channels.
14
Usage
Channel adjustment
Expert Transmitter:
Directly slide the Channel Switch to the channel you need. When power on, the times STATUS LED
blink shows the channel at present.
Expert Receiver:
When power on, the current channel would be shown on the top left corner of the screen. Slightly
press [CHANNEL SWITCH/WAKE UP] to change the channel.
Switching the channels of receiver can monitor the image from different channels.
[CHANNEL SWITCH/WAKE UP] button has the function of sleep and wake-up mode. Hold and press
it to get into the sleep or wake-up mode.
15
Usage
Usage
Connect with the camera
Holding Expert Transmitter
Available to hold the transmitter on hot shoe, rack or tripod.
1. Insert
1.Hold the transmitter on the hot shoe of camera.
Lock the hot shoe locknuts.
Loosen the hot shoe locknut first when you remove
the transmitter. Do not forcibly pull out it, in order to
avoid damage to the transmitter and camera.
* The shutter cable has various models to match with different
camera .
2. Insert video cable B side to transmitter A/V socket, insert another
(Picture1)
side to camera A/V output.
*The video cable has various models to match with different camera.
2.Fix the transmitter on the rack of camera accessory.
3.Fix the transmitter on the tripod.
Make sure the transmitter is held firmly so that will
not fall down.
(Picture2)
16
shutter release cable A side to transmitter shutter release
socket, another side insert to camera shutter release socket .
AN OUT
HDMI OUT
MI C
(Picture3)
17
Usage
Switching Signal Source
Receiver directs to convert the input signal source of transmitter.
Press [CCTV/AV] when camera's LV mode is on and AV signal has connected to transmitter, the input
signal source of transmitter will convert between AV and CCTV.
Usage
Enlarge and review
1. Under the CMOS mode, slightly press the Enlarge and Check button [
] to enlarge display
function, and the Screen display effect will be magnified one times. Press [up/down]/[right/left]
to move the displaying scope. Press [
] again to exit enlarge display function.
2. Press [
Press [
] for two sec to get in Review mode; LCD shows the saved picture in the receiver.
] again to exit Review mode.
3. In review mode, available to paging-through, delete or delete all images in receiver.
4. Press [right/left] to page through the saved image.
5. Press [OK] to exit delete menu, press [up/down] to select the choice, press [OK] to confirm the
choice.
Available to delete one or delete all images.
18
19
Usage
Usage
Sleep/Wake-up mode
Under operation status, hold [CHANNEL SWITCH/WAKE UP] for two sec, and the screen will get into
sleeping mode.
Under sleeping mode, hold [CHANNEL SWITCH/WAKE UP] for two sec, and the screen will get into
monitor mode.
*Setting sleep mode in menu.
Menu
1. Press [MENU] to enter the menu.
2. Press [right/left] to select submenu. Press [up/down] to select items in submenu.
3. Press [OK] to execute the selected item.
SYNC
LCD Brightness adjustment
SLEEP：
SLEEP
Sleeping mode setting: No Sleep (OFF), One minute into Sleep(1 MIN), Three
minutes into Sleep(3 MIN), Five minutes into Sleep(5 MIN), Seven minutes
into Sleep(7 MIN).
OFF
1 MIN
Under operation status, press [right/left] to adjust the screen brightness. The LCD brightness is
divided into ten grades; the current grade is shown on the right bottom corner when adjusting.
3 MIN
Volume adjustment
Under operation status, press [up/down] to adjust the volume. The volume is divided into ten grades;
the current grade is shown on the right bottom corner when adjusting.
*Receiver would have the audio output when transmitter has audio input.
20
SAVE
SYNC
YES
NO
SLEEP
SYNC：
Sync code-matching setting: enter code-matching mode (YES), exit codematching mode (NO).
21
Usage
DRIVE
SAVE
Usage
SYNC
BEFORE
AFTER
SAVE： Screen shot saving setting: Save before taking the shot (BEFORE),
Save 1.8 sec after taking the shot (AFTER), No saving (OFF).
OFF
AVOUT
DRIVE
SAVE
SINGLE
CONTINU
DELAY 2 S
VER
AVOUT
DRIVE
TV
TFT LCD
VER
AVOUT: Video output setting: External AV video interface (TV), LCD display
screen (TFT LCD).
*With connected external monitor, randomly to switch between the external
monitor and the LCD display.
AVOUT
TX 000.000
RX 015.013
22
DRIVE： Shutter function setting: Single shooting (SINGLE), Continuous
shooting (CONTINU), 2sec Delay shooting (DELAY 2S), 5sec Delay shooting
(DELAY 5S), 10sec Delay shooting (DELAY 10S).
VER： Version checking function: to check the version of transmitter and
receiver.
Remote Shooting
Single Shooting:
Set the receiver shutter function as single shooting (SINGLE), and set the camera shutter function as
single shooting.
Continuous shooting:
Set the receiver shutter function as continuous shooting (CONTINU), and set the camera shutter
function as continuous shooting.
BULB:
Set the receiver shutter function as continuous shooting (CONTINU), and set the camera shutter
function as BULB.
Delay shooting:
Set the receiver shutter function as two sec delay shooting (DELAY 2S), and set the camera shutter
function as single shooting.
Half press receiver shutter release button to focus; full press the receiver shutter release button to
shoot after two sec.
*Three grades of delay time: 2 sec, 5 sec, and 10 sec.
23
PIXEL Expert Specifications
Type:
Distance:
Transmitter:
Receiver:
Dimensions:
(W×H×D)
Weight:
ISM 2.4GHz frequency channel which qualified CE or FCC standard.
200 meters
Standby time:
100 hours
Working time:
1 0 hours
Standby time:
500 hours
Working time:
12 hours
Transmitter:
62.6mm×39.2mm×166mm
Receiver:
12 2mm×27.9mm×73.4mm
Transmitter:
88.5(without battery)
Receiver:
128(without battery)
Now you can start to use unique high-performance PIXEL product
Expert. If you have any questions, you can contact the local
distributor. Or visit the website http://www.pixelhk.com.
24

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 14
Create Date                     : D:20111012024537
Modify Date                     : D:20111012024537
Producer                        : Corel PDF Engine Version 3.0.0.667
Author                          : chenlh
Creator                         : CorelDRAW
Title                           : LV-W2英文文说明书 2011.5.18

EXIF Metadata provided by EXIF.tools