Planet Technology WNAP6325 802.11n Wireless Outdoor CPE User Manual A9R5F2

Download:
Mirror Download [FCC.gov]
Document ID	2677658
Application ID	oj0yLjo3MaYQfKWpP9SQ7A==
Document Description	Users Manual part 2of5
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	354.02kB (4425274 bits)
Date Submitted	2015-07-13 00:00:00
Date Available	2015-07-13 00:00:00
Creation Date	2015-07-08 11:58:00
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2015-07-08 11:58:17
Document Title	A9R5F2.pdf
Document Creator	PScript5.dll Version 5.2.2
Document Author:	User

User Manual of WNAP—6325
Ethernet Cable
Data
PC
1 24V PoE Injector
POE Port
Ethernet Cable
Data+Power ®
Figure 3-3 Connect the PDE Injemor
Figure 3-4 Pole Mounting
User Manual of WNAP—6325
Chapter 4. Quick Installation Guide
This chapter will show you how to configure the basic functions of your AP within minutes.
4.1 Manual Network Setup - TCPIIP Configuration
The default IP address of the WNAP—6325 is 192.168.1253. And the default Subnet Mask is 255.255.2550.
These values can be changed as you desire. In this guide, we use all the default values for description.
Connect the WNAP-fi325 with your PC via an Ethernet cable which is then plugged into a LAN port of the PoE
injector with one end and into a LAN port Of the PC with the other end. Then power on the WNAP£325 Via POE
injector or PoE switch,
In the following sections, we’ll introduce how to install and configure the TCPIIP correctly in Windows 1. And the
procedures in other operating systems are Similar. First, make sure your Ethernet adapter is working, and refer
to the Ethernet adapter’s manual if needed.
4.1.1 Configuring the IP Address Manually
Summary:
I Set up the TCPIIP Protocol for your PC,
I Configure the network parameters. The IP address is 192.168.1.xxx (”)o Run,
2. Type ‘cmd” in the Search box.
User Manual of WNAP-6325
irng’mii 1
I! and
See more VESU I:
wit Shumawn ‘ u ‘
Figure 4-2 Windows Start Menu
3 Open a command prompt and type ping 192,168,1253, and then press Enterv
If the result displayed is sxmxlar to Flgure 4-3, \t means the connection between your PC and the AP
has been establwshed well,
Figure 4-3 Successful result of Ping command
If the result displayed is stmwlar to Figure 4-4, \t means the connection between your PC and the AP
has failed
User Manual of WNAP-6325
acmwmpmpt ' ' 0'". o O Una-'0 . [a
mu (9 1.-K.(.;!Er!
\‘ t”
r uncd an
I turned mil ,
Figure 4-4 Failed result of Ping command
If the address is 0 0 0 0, check your adapter installation, security settings, and the settings on your AP, Some
firewall software programs may block a DHCF> request on newly installed adapters.
4.2 Starting Setup in the Web UI
It is easy to configure and manage the WNAP-6325 with the web browser.
Step 1. To access the configuration page, open a web browser and enter the default IP address
ht_t2:lI192.168.1.253 in the web address field of the browser.
File Edit View Favorites Tools Help
Figure 4-5 Login by default IP address
Afler a moment, a login window will appear. Enter admin for the User Name and Password, both in lower case
letters. Then click the OK button or press the Enter key.
.24.
User Manual of WNAP—6325
Windows Security a
The server192.168.1‘253 is asking for your user name and password, The
sewer reports that it is from ,"WNAP-63E,
Warning: Vour user name and password will be sent uslng basin
authenticatlun on a connection that lsn‘t secure
‘: admin —‘
D— Remember my credentials
Figure 4-6 Login Window
Default IP Address: 192.1 68.1.253
Default User Name: admin
Default Password: admin
/ 2, If the above screen does not pop up, it may mean that your web browser has been set to a
@J} proxy. Go to Tools menu>lnternet Optlons>Connectlons>LAN Settlngs in the screen
Note that appears, cancel the Using Proxy checkbox, and click OK to finish lt.
Afler entering the usemame and password, the Operation Mode page screen appears as in Figure H
0% NET
I cum-muo-
| SySlEmcDHfiaumfiOn | Tools | Devxce Slams \ Logan! |
Mod:
Access Poml
(0)
Guam
WDS AF
was client
AP Rouler
OOOOO
Wire’ess ISP
. Operalion Mode
Li”) W U-AJ‘ :2
User Manual of WNAP—6325
"(NAIL—6325
300Mbps 802.11n Wireless Outdoor CPE
mm; (H ‘EULD‘ mm a E m:r E
Setup
semp
setup
Setup
setup
Setup
Radio
Access Palm
Client
WDS ALzEs Point
WDs CI'Enl
M6955 Palm
Wireiess ISP
Flgure 4-7 WNAP—6325 Web UI Screensth
the omer Operation Modes.
PLHNET
| System Configumfion | Tools | Device Status \ Logan! |
Mod-
L) Access Pom
CI Clienl
(03 WDSAF
c wnscnem
C, AP Router
0 Wiretess ISP
. Operation Mode
Enema Fon
LANrLAN
LAN+LAN
LAN+LAN
LAN+LAN
WAN‘LAN
LANHAN
Sliep 2. You can choose an Operation Mode. Please refer lo the instructions in he next chapter for configuring
300Mbps 802.11n Wireless Outdoor CPE
:2 “mum ,
Setup
SetuD
setup
Setup
Setup
Selup
Figure 4-8 Choose Operation Mode
Save button to make me configuration take elred immediately.
Rad")
Access Point
Client
WDS ALcess F'olnt
WDS Clem
Access Pom!
Mreiess ISF'
imam" For!
LAN+LAN
LAN+LAN
LANv-LAN
LAN¢LAN
WAN+LAN
LAN+LAM
Step 3. Please enter the SSID and configure your Encryption Seflings, Pre-Shaied Key, etc. Then click the
6 mm 192.168.1153'5Hmtu aip
User Manual of WNAP—6325
Security Settings
Select Encryption:
WPA2
Dre-Aulhenti cation:
Encryption Type:
Pre-Snared Key:
Petsonal (Prersnareu Key)
: Enterpnse (RADIUS)
‘ :1 TKIP L . Auto
12345578 x
Save Cancel
Figure 4-9 Configure ereless Settings
User Manual of WNAP—6325
Chapter 5. Configuring the AP
This chapter delivers a detailed presentation of AP’s functionalities and features under 4 main menus
(Operation Mode, System Configuration, Tools and Device Status) below, allowing you to manage the AP
with ease.
”(NAB-6.72 A
mnem- 300Mbps 802.11n Wireless Outdoor CPE
i System Configuration i Tools | Device scams | Lngaut i
Figure 5-1 Main Menu
5.1 Operation Mode
On this page, you can select different operation modes of the WNAP-6325, Including Access Point, Client, WDS
AP, WDS Client, AP Router and Wireless ISP.
WNAE‘EJ 5
300Mbps 802.11n Wireless Outdoor CPE
l SystemConfigumlion | Tools | Dem Status i Logan: |
- Operation Made
9:7 Wr firw'amii.‘ u:- :v. illHlLl‘H‘ir‘ll‘l in“ Hummer“ ,i :g‘rrnr slur-Mt «Mugs
Mode Radio Ememel Fan
[03 Access Poinl Setup Access Point LANv-LAN
0 Client setup Client LAN+LAN
O WDS AP Setup was Access Point LANoLAN
C) WDS Client Setup WDS Cient LANtLAN
0 AP Router Setup Access Point WAN+LAN
O vwrekss ISP Setup Vlflreless ISP LANrLAN
Figure 5-2 Operation Mode
5.1.1 Access Point
Click “Operation Mode" —) “Access Point" and the following page will be displayed. This section allows you to
configure the Access Point mode.
u Operation Mode
User Manual of WNAP—6325
- Operation Mode Settings
Regulatory Domain: Europe v
Network ID (SSID) WNW-6325
Site Survey
2 Enable \Mrsless
3 Disable SSID Broadcasting
1 Enable Isolated
Radio Mane: m
manner: a ~2437MH1 v
Data Rate: Auto v
Security Setting: Setup
Transmit Power: 27 ohm v
Transmit Distance: 1 Km v
TDMA: Disable v
Advanced Setfinus: Setup
Access Cnntrul' Setup
Figure 5-3 Basic Settings -AP
Object l Descr tion
. Regulatory Domain
Select your domain from the list.
0 Network SSID
It is the Wireless network name. The default SSID is
WNAP-6325.
. Slte Survey
Click ”Site Survey’ to check the signal of remote sites.
0 Enable Wireless
Check it to enable Wireless function.
0 Disable SSID Broadcasting
Check it to disable SSID broadcasting.
Enable Isolated
Check it to isolate each connected wireless clients so that they
cannot access each other.
Select the channel Width to "Auto Select', ‘2G 11 MG HT20" or
Radio Mode
"26 11 MG HTM)”
Select the operating channel you would like to use. The channel
. Channel _ . _ _
range will be changed by selecting a different domain.
Select MCSO~15 or Auto from the pull-down menu. The default is
. Data Rate
"Auto'.
. Security Setting
Press “Setup“ for more configurations. Please refer to 5.1.7
Security Setting for more information.
. Transmit Power
The range of transmit power is ‘12~27 dbm". In case of
shortening the distance and the coverage of the wireless
User Manual of WNAP—6325
network, input a smaller value to reduce the radio transmission
power.
Transmit Distance
Select a spectied distance of the two nodes.
. TDMA Displays the System Time.
Press “Setup" for more configurations. Please refer to 5.1.8
Advanced Settings
Advanced Settings for more information.
Press “Setup" for more configurations. Please refer to 5.1.9
Access Control
ACCESS Control for more information.
5.1 .2 Client
Click ”Operation Mode” -) “Client” and the following page will be displayed. This section allows you to
configure the Client mode.
> Operation Mode Settings
, Dpernt'innM tie
0 Regulatory Domain
Regulatory Domain: Eu rope v
Renate AP SSID: WNW—6325 Site Survey
R Enanle ereless
: Disable 35 ID Bruadi: 351ng
# Enable lsdaled
Luck to AP MAC: 00:00 DD 0000:00
Radiu Mode: 3m
cnannei: mm
Data Rate: 1% 7v
Securiiy Setting: Setup
Transmit Power. 27 film v
Transmit Distance: 1 Km v
TDMA: Disable u
Advanced settings: setup
Access Cnntrol' Setup
Figure 5-4 Basic Settings - Client
Select your domain from the list.
- Network SSID
MAP—6325.
It is the wireless network name The default SSID
is
0 Site Survey
Click ‘Site Survey" to find the remote sites to associate
0 Enable Vlfireless
Check it to enable Wireless function.
User Manual of WNAP—6325
- Disable SSID Broadcasting Check it to disable SSID broadcasting
Check it to isolate each connected wireless clients so that they
Enable Isolated
cannot access each other
Look to AP MAC Enter the Mac address of the remote AP.
Select the channel width to "Auto Select”, ‘2G 11 MG HTZD' or
Radio Mode
“26 11NG HT4-0”
Select MCSO~15 or Auto from the pull-down menu. The default
a Data Rate
is “Auto”.
Press “Setup" for more configurations. Please refer to 5.1.7
o Securl Settln
ty 9 Security Setting for more information.
The range 01 Transmit power is “12~21 dbm'. In case of
shortening the distance and the coverage of the wireless
0 Transmit Power _ _ _ _
network, Input a smaller value to reduce the radlo transmissmn
power.
0 Transmlt Distance Select a specified distance of the two nodes.
0 TDMA Displays the System Time.
Press "Setup' for more configurations. Please refer to 5.1 8
. Advanced Settings
Advanced Settings for more information.
Press "Setup' for more configurations. Please refer to 5.1 9
0 Access Control _ _
Access Control for more Information.
5.1 .3 WDS AP
Click ‘Operation Mode" -) “WDS AP" and the following page will be displayed. This section allows you to
configure the WDS AP mode. For eadl wireless parameter, please refer to section 5.1.1 AP for more
information .
.31 _
User Manual of WNAP—6325
> Operation Mode Settings
. Operation Mode
Requamry Domain: Europe v
Network iD [SSID) WNAF'5325 312 Survey i
E Enauie Wneiess
Dsabie SSID Broadcastlng
Enable Isoaiea
Radio Mode: 26 4b
manual: 6 -2A37MHZ v
Data Kala: Aum v
security 59mm}: Setup
"ans"!!! Powen 27 dbm v
Transmit Distance: 1 Km v
IDMA: Disable v
Advanced Settings: Setup
Access Control: Setup
Figure 5-5 Basic Settings — WDS AP
5.1 .4 WDS Client
Click “Operation Mode” -) ‘WDS Client" and the following page will be displayed. This section allows you to
configure the WDS Client mode. For each wireless parameter, please refer to section 5.1.2 Client for more
information.
User Manual of WNAP—6325
- Opernlion Mode Settings
, Operation Mode
Regulatory Dom-in: Eu rage v
Remote AP ssro: WNW-6325 sne Survey
l2 Enable \Mreless
3 Disable SSID Broadcasung
3 Enable Isolated
Lock Lo AP MAC: mono» 00.00.09
Rama Mode: 25 11m; HTM] v
Channel: W.
Data Rate: Auto v
Security Semi rm: Setup
Transmit Power. 27 film v
Tranmil Distance: ’m
mum: 053le v
Advancsd Sailings: setup
Amen cmtmr: setup
Flgul'e 5-6 Basic Settings 7 WDS Client
5.1.5 AP Router
Click ‘Opelalion Mode" -) “AP Router" and the following page will be displayed. This sedion allows you 10
configure the AP Router mode.
User Manual of WNAP—6325
- Openbm Mode Serums
Regulatniy Domain: Eumpe v
"mink ID (5 SD) WIMP-€325 SIB Sum!
EnableMeless
El Disable 5519 Wasting
El inane ljnlaied
than was 25 ”N5 rmu v
Channel: 5 72l37MH: V
Dill flair: v
35
Searrity smug:
Transmit PM 27' Gram V
Transmit Distance I Km v
TWA: Disable V
Advanced seams.
Ami: cml:
WAN Pun Selfinuaz
Dynamic nus SIIIIIDE:
Ran-me "filament
DHCP Server Settings:
wz Settings:
Virtual Server swings:
IF Filtering Minus:
Pan airman Senings:
um: Filtering mums:
Bandwidth Cordial:
§§§§§§§§§E§l§§
Figure 5-1 Basic Semngs iAP Router
5.1 .6 Wireless ISP
Click “Operation Mode‘ 9 “Wireless ISP" and lhe following page will be displayed. This sedion allows you lo
configure the Wireless ISP mode.
User Manual of WNAP—6325
. Dpelafion Made smngs
Regulatory Domain: Europe v
Ran-009A? 55m: MAP-6325 smear-way
El Enable “was
El Diana 5le Emadoamng
El Enable Isnlm
Loeklo AP MAC: uuw-un-muuw
Rania Made 26 “NE Hm: v
Channel:
um an: Auto v
mmy Sm": Sump
Transmit Power: 27 am v
Transmit Drstznoe 1 Km v
TDMA: Disable v
Ammced seams: Saw
Access Comml: Setup
WAN Port Settings: Sen-p
Dynamic nus Smngs: sump
Remote Managemmt Setup
DHCP Server Sailings: Setup
DMZ mulls: Setup
lam-3| Sena Settings, Set-w
IF Finenng mugs: setup
Port Filming Settings: Setup
MM: Filtering saunas: Sen-p
Bandwidth Comm: Sump
sum: Sena
Figure 5-8 Basic Settings — WISP
5.1 .7 Security Setting
Choose the operation mode you required, and then enter "Security Setting” by clicking the Setup button next to
it and the following page will be displayed This section allows you to configure the wireless security settings.
Security Settings
Select Encryption: l None v]
Saws Cancel
Figure 5-9 Security Settings
User Manual of WNAP—6325
Object Description
Select the encryption that you need
None: No security required
WEP: Input 5, 13 (ASCII) or 10, 26 (HEX) character for WEP
key.
WPA: Enter ASCII characters between 8 and 63 character or 8
. Select Encryption to 64 hexadecimal characters.
WPAZ: Enter ASCII characters between 8 and 63 character or
8 to 64 hexadecimal characters.
WPA-Mixed: Enter ASCII characters between 8 and 63
character Of 8 to 64 hexadecimal characters.
l None
Authentication is disabled and no password/key is required to connect to the access point.
I WEP
WEP (Wired Equwalent Privacy) is a basnc encryption For a higher level of security consider usmg the WPA
encryption.
Security Settings
Seiecl Encryption: J
Authentication: 6) Open System <3 Shared K2; 0 Auto
Key Length: (-3- 64-bit O 1 28-bit.
Key Format: Aswa’c’naranere: vi
Encrypuun Key:
Figure 5-10 Security Settings — WEP
Object ‘ Description
. Authentication I You can select Open System, Shared Key or Auto.
0 Key Length ‘ Choose the WEP key length. You can choose 64-bit or 128-bit.
0 Key Format ‘ You can choose ASCII or Hex,
o Encryption Key Enter the keys in the fields.
WPA
Pre-Authentlcatlon
User Manual of WNAP—6325
Security Settings
Select Encryption: [WPA v ‘
Pre-Aumenijcalmli: @‘Fersonal iPre~Shared K2 : OEnterprise (RADIUS)
Encryption Type: Om? Q A53 (-3 Auto
Fre-Shured Key: l i
cm:
Figure 5-11 Security Settings — WPA Personal
preAumenircauon: 0 Personal [Freesnarea Keri ('3‘ Enterprise (RADIUS:
Encryption Type: C- TKIP O AES (0 Auto
RADIU ServerlP Address: ‘
RADIU Server Part: ‘
RADIU Server Password: ‘
EAP Reamhonzation Period: ‘Setunds i300 - 36m Secnnds:
RSN Reamhonzatlom Disable v
WPA Group RBKEY lmeWfl'? Seconds i300 ~ 3600 Seconds:
Save Ca ncEl
Figure 5-12 Security Settings 7 WPA Enterprise
Select “Personal (Pro-Shared Key)" or "Enterprise (RADIUS)"
encryption type.
. Encryption Type Set the WPAto be TKIP, AES or Auto.
o Pre—Sl’lared Key Enter the keys in the fields.
o RADIU Sewer IP
Address
Enter the RADIUS sewer host IP address.
- RADIU Sewer Port
Set the UDP port used in the authentication protocol of the RADIUS
sewer. Value must be between 1 and 65535.
o RADIU
Password
Server
Enter a shared secret/password between 1 and 99 characters in length.
User Manual of WNAP—6325
o EAP
Reauthorization Set duration Of SESSION timeout In seconds between 300 and 3600‘
Period
0 RSN
Enable or disable RSN reaulhorizaiion.
Reauthorization
o WPA Group Rekey
Set duration of session timeout in seconds between 300 and 3600.
Interval
l WPA2
Please refer to WPA for more infomialion.
Security Settings
Select Encryption:
Warflumemiwlioni (9 Personai iFrerSnared K9,: 0 Enterprise iR~.DiUS.
Encryption Type: O TKIP 0 RES (0) :uto
Pre-shared Key:
Figure 5-13 Security Settings , WPA2 Personal
WGAUmeillcallmi O Personai iF‘re-Snarea K9,: 6) Enterprise iReDIUS‘
Encryption Type: O TKIP C) aES ® min
RADIU Sewer IP Address:
RADIU Sewer Port:
RADIU Sewer Password:
EAP Reaulnonzanm Period: iSenands i300 \ 35m Secondsi
RSN Reaulhorilaliun: Disable?
WPA Group Rakey Interval: iSecunus r330 ‘ 3500 Seconds:
Figure 5-14 Security Settings — WPA2 Enierprise
User Manual of WNAP—6325
I WPA-Mixed
Please reier i0 WF’A fOI more information.
Security Settings
Select Encryption: lXed v
PFE-Aulhenl-icafioni @Fersdnal xFrerShared Ke»: OEnlerpnse IRLDIUS:
Encrypuon Type: O TKlP O AES (9 min
Prersnared Key:
cm
Figure 5-15 Security Settings — WPA»MiXed Personal
PreAmhenlIcatinn: QPersohal Mare—Shared K2,: @Enlerprlse lRADiUS
Encryption Ty pa: 0 TKIP O alas (9 auto
RADIU Server IF Address:
RADIU Server Pun:
RADIU Sewer Password:
EAP Realllflorllallm Period: Seconds i330 \ 3500 Seconds:
RSN Reaulhorilation: Disable v
WPA GTOUP Rakey Imen'fil: Seconds [500 \ 3500 Seconds:
Figure 5-18 Security Settings — WPA—Mixed Enterprise
5.1 .8 Advanced Settings
Choose the operation mode you require, and then enter “Advanced Settings" by clicking Setup button nexl lo it
and the following page will be displayed. This section allows you to configure the wireless advanced settings.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : User
Create Date                     : 2015:07:08 11:58:00+08:00
Modify Date                     : 2015:07:08 11:58:17+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2015:07:08 11:58:17+08:00
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : A9R5F2.pdf
Creator                         : User
Document ID                     : uuid:ddfe104d-700d-47d4-8b86-d737427e7e0c
Instance ID                     : uuid:430f51d9-a069-4e2b-a1ae-9674b5fbf31e
Producer                        : Acrobat Distiller 11.0 (Windows)
Page Count                      : 20

EXIF Metadata provided by EXIF.tools