Plantronics CA12CDSX Cordless PTT Base Unit User Manual

Plantronics Inc Cordless PTT Base Unit Users Manual

Users Manual

Download: Plantronics CA12CDSX Cordless PTT Base Unit User Manual
Mirror Download [FCC.gov]Plantronics CA12CDSX Cordless PTT Base Unit User Manual
Document ID2297669
Application IDprRoX4bZ6tyXSFo1bJMFiA==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize69.85kB (873077 bits)
Date Submitted2014-06-17 00:00:00
Date Available2014-06-18 00:00:00
Creation Date2017-10-22 09:13:37
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-10-22 09:13:37
Document TitleUsers Manual
Document CreatorAdobe InDesign CS5 (7.0)

C      C
USER GUIDE
Charging Well for
Spare Battery Pack
M 
P
Audio Link
LED Button
.................................................................
alk Headset Amplifier
Push-toTalk
Button
C 
Console
Interface Cable
AC Adapter
Charging Well for
Remote Unit
Listen
Fine-Adjust
Switch
Remote Unit
Battery Charge LED
(Orange)
SPARE
CHARGE
TALK
VOLUME
BASE
POWER
SPARE
CHARGE
BASE
POWER
TALK
VOLUME
Quick Disconnet™
for Headset
REMOTE
CHARGE
Battery
Pack
See Note 3.1
TALK
Momentary/
locking PTT
Selector
(not shown;
see Fig. 1.7 and
Note 4.1)
Spare
Battery Pack
Charge LED
(Orange)
PTT LED
(Green)
REMOTE
CHARGE
TALK
Talk Volume
Buttons
(fine-adjust)
See Note 4.1
Base Unit
Power LED
(Green)
BOTTOM VIEW
OF BASE UNIT
REMOTE UNIT
Setup and Operation
Pluc AC
Adapter
in here
Plug Console
Interface Cable
in here
Subscription
Button
BACK VIEW OF BASE UNIT 1.1, 1.2
1.1 Plug the modular connector on the Console Interface Cable into
the modular jack on the back of the Base. Plug the other end into
your console.
1.2 Plug the AC adapter into a wall outlet, and plug
the power connector into the back of the Base.
The Base Power LED will turn on.
1.3 Slide the battery pack onto the Remote and snap
it into place without forcing it. The CA12CD-S will
take a few seconds to select the most reliable
radio channel, and then it will start to blink its
Audio Link LED at once per second, to indicate
that it is ready to use.
1.4 For first-time use, press the Audio Link button to
turn the audio link off, and place the Remote into
its charging well to charge the attached battery
pack.
1.5 Place the spare battery pack into its charging well.
1.6 The Charge LEDs will flash until the battery packs
are fully charged, at which time the LEDs will
stop flashing and remain on. (It is okay to use the
Remote after only one hour of charging time if
1.3
desired.)
Installing the Battery Pack
In low-density installations (e.g., 5 units placed 10 feet apart), the
range can be greater than 100 feet. In high-density installations
(e.g., 30 units placed 18 inches apart), the range could decrease
to as little as 10 feet. In general, it is best to place them as far
apart from each other as possible.
2.4 Keep cell phones at least 3 feet from both the Base and the
Remote when the Remote is not near the Base. When the Base
and Remote are near each other, cell phones can be closer than
3 feet, but should never be placed right next to the Base or
Remote.
2.5 Remove the battery pack and power cord from any unused units
to allow more radio spectrum for active units. This is especially
important where large numbers of them are in use.
Battery Charging
and Management
Subscribing Remotes
and Bases
The Base and the Remote are paired with each other at the factory
in a process called subscription. If you replace either one, you can
subscribe them as follows:
4.1 Press and hold the Subscription button on the back of the
Base. (Alternatively, you can hold both of the Talk Volume
buttons on the top of the Base down.)
a. The Base Power LED will begin blinking.
4.2 Hold the Remote’s Listen Volume Control in either the up or
down position.
a. The Remote’s Audio Link LED will turn on steadily (no
flashing). The Remote will subscribe to the Base, after which
the Base Power LED will return to the steadily-on state. The
Remote’s Audio Link LED will go out for a few seconds and
then begin to flash once per second, indicating that your
CA12CD-S is now ready to use.
Note 4.1: Remotes and Bases from different models and product
generations cannot be mixed. Please see Table 4.1.
Table 4.1: Compatibility of Remotes and Bases
Color of
Momentary/
Locking Selector
on Remote (see
Figure 1.7 for
location)
Color of
Talk Volume
Buttons on
Base
Model &
Product
Generation
Primary
Region of Use
Black
Black
CA12CD,
1st Gen.
North
America
White
Black
(check label
on bottom of
base to verify
model)
CA12CD/A,
1st Gen.
Europe
Gray
Gray
CA12CD-S,
2nd Gen.
North
America
Purple
Purple
CA12CD-S/A,
2nd Gen.
Europe
1.7 Press the PTT Button on the Remote to key up your
communications radio. The Talk LED on the Base will turn on
whenever the PTT button is pressed.
1.7 How to set the PTT button for locking or momentary operation
Locking
Momentary
Locking Operation
When the selector’s slot is aligned with the Remote’s centerline, the PTT button can be depressed momentarily or locked
in the ON position by first depressing then sliding the button
down toward the selector until the button locks into place.
Momentary Operation
Turning the selector 90 degrees from the locking position will
set the PTT button for momentary operation.
3.1 A new, fully charged battery pack will last for about 8 hours,
however, we recommend swapping the Remote’s battery pack
with a freshly charged battery pack from the Spare Charger
about every 4 hours. Doing so will help insure that missioncritical communications are not interrupted by low batteries.
Following this recommendation will also maximize the battery’s
service life.
3.2 Between battery swaps, we recommend placing the Remote in
its charging well whenever possible, and, if it is not being used,
turning the audio link off by pressing the Audio Link button.
3.3 If the Remote is left in the charging well with the link up, a new
charging cycle will typically begin about 3 hours after the first
charging cycle. Using the Remote at this time without installing
a freshly charged battery pack could result in reduced talk time.
3.4 A completely depleted battery pack requires about 4 hours to
fully charge.
3.5 The Remote will continue to draw a small amount of power
from the battery even after being turned off. If you need to
store the Remote, remove the battery pack so that it does not
become completely discharged while in storage.
Warning: Touching the battery-charging contacts or placing objects
other than the battery packs and Remote in the charging wells may
adversely affect the operation of the CA12CD-S.
Note 3.1: Rechargeable batteries of all types gradually age and lose
their ability to give and receive charge. Over time, this will result
in gradually decreasing talk times. In a typical 24/7 operation,
where the batteries are regularly being charged and discharged, we
recommend that you monitor their performance and replace them
as needed.
Listen
Coarse-Adjust
Switch
BASE UNIT
Performance Tips
2.1 Careful setting of the audio levels, both in your communications
console and in the CA12CD-S, is essential for getting good audio
quality and avoiding echo. Please see the separate sheet, Audio
Settings Guide for the CA12CD-S, for detailed advice.
2.2 Operating other radio devices, such as DECT cordless handsets,
in the same frequency band as the CA12CD-S will reduce the
number of units that can be operated at one time, along with
reducing their maximum range. In North America, the CA12CD-S
operates in the UPCS frequency band (1.92 to 1.93 GHz). In other
regions (e.g., the European Union), the CA12CD-S operates in the
DECT frequency band (1.88 to 1.90 GHz).
2.3 User density and range can vary widely due to such variables as
building layout and whether other devices are operating in the
same frequency band as the CA12CD-S.
Talk
Coarse-Adjust
Switch
CONTROLS
ERROR CONDITIONS
Name
Location
Function(s)
Push-to-Talk
(PTT) Button
Remote
Keys up the communications radio.
If you hear a…
It means…
Triple beep
Your Remote has lost its audio link with
the Base. Usually, this is due to being too
far away from the Base. (Note that a triple
beep while using the Talk or Listen fine
adjust controls indicates that the level is
at its nominal setting.)
LockingMomentary
Selector
Remote
Enables or disables locking
operation of the PTT Switch
Audio Link LED
Button
Top of
Remote
Turns the audio link between the
Remote and the Base on and off.
Single beep every
10 seconds
Your battery is low and should be
changed or charged.
Listen FineAdjust Switch
Remote
1. Adjusts the Listen sensitivity in
2-dB steps.
2. Places the Remote into
Subscription Mode when pressed
and held in either the Up or Down
position.
If you see…
It means…
The Audio Link LED
flashing six times per
second
Your Remote is not subscribed to the
Base. See the instructions in the next
section for subscribing Bases and
Remotes.
Listen CoarseAdjust Switch
Bottom
of Base
A Charge LED flashing
six times per second
Your battery should be replaced, or there
could be an object such as a coin or a
paperclip in the charging well.
Adjusts the Listen sensitivity in 6-dB
steps.
Talk Volume
Buttons
(fine-adjust)
Top of
Base
1. Adjust the Talk sensitivity in 2-dB
steps.
2 Set the Talk sensitivity to
midrange when both are pressed
quickly at the same time.
3. Place the Base into Subscription
Mode when both are pressed and
held at the same time.
Some versions of the CA12CD-S do
not have these buttons.
Talk CoarseAdjust Switch
Bottom
of Base
Adjusts the Talk output for
carbon-, electret-, or dynamic-mic
applications. Carbon (Position 4) is
the factory setting, and is suitable
for most applications.
Subscription
Button
Back of
Base
Places the Base into Subscription
Mode when pressed and held (this
is an alternative to pressing and
holding the Talk Volume buttons).
LEDS
Name
ATTENTION:
Interruption or termination of the communications link between
the Base and the Remote will occur under the following or similar
conditions:
1. Power outage
2. Moving the Remote out of range from the Base
3. Pressing the Audio Link button on the Remote while the audio link
is active
4. Disconnection of the Base’s power supply
5. Removal of the battery pack from the Remote
6. Low battery
7. Operation of other radio devices in the same frequency range
(1.92 to 1.93 GHz for North America and 1.88 to 1.90 GHz for
Europe and some other regions) as the CA12CD-S.
8. Too many CA12CD-Ss in the same location. At least 30 can
typically be operated in the same location. However, this number
can vary depending on such factors as building layout and
materials, physical separation of units, and other radio devices
operating nearby.
FCC PART 15 REQUIREMENTS
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
Location
Function(s)
Top of
Remote;
part
of the
Audio
Link LED
Button
1) Flashes once per second to
indicate an active audio link.
2) Glows steadily (no flashing) when
the Remote is in Subscription Mode.
3) Flashes 6 times per second if the
subscription is lost (see the next
section for more information).
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
Power (green)
Base
1) On continuously when the Base is
powered up
2) Flashes once per second
when the Base is in Subscription
Mode.
Talk (green)
Base
On steadily (no flashing) when PTT
button is depressed.
Base, 1
for each
charging
well
1) Flashes once per second while
the battery is charging.
2) On steadily when the battery is
fully charged.
3) Flashes six times per second to
indicate a fault condition (see the
next section for more information).
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception which can be determined
by turning the radio or television off and on, the user is encouraged
to try to correct interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on another circuit.
4. Consult the dealer or an experienced radio/TV technician for help.
Audio Link
(green)
Charge (orange,
2 ea.)
Exposure to Radio Frequency Radiation
This device and its antenna must not be co-located or operated in
conjunction with any other antenna or transmitter. To comply with
FCC RF exposure requirements, use only the supplied antenna.
The radiated output power of this internal wireless radio is far below
the FCC radio frequency exposure limits. Nevertheless, the wireless
radio shall be used as described in the manual.
The internal wireless radio operates within guidelines found in radio
frequency safety standards and recommendations, which reflect the
consensus of the scientific community.
Plantronics therefore believes the internal wireless radio is safe for
use by consumers. The level of energy emitted is far less than the
electromagnetic energy emitted by wireless devices such as mobile
phones. However, the use of wireless radios may be restricted in
some situations or environments, such as aboard airplanes. If you are
unsure of restrictions, you are encouraged to ask for authorization
before turning on the wireless radio.
In order to comply with FCC and IC RF Exposure requirements,
the base must be installed and operated such that a minimum
separation distance of 20 cm is maintained between the base and
all persons during normal operation. The Remote complies with FCC
radiation limits set forth for an uncontrolled environment.
NOTE: Modifications not expressly approved by Plantronics, Inc.
could void the user’s authority to operate the equipment.
INDUSTRY CANADA REGULATORY INFORMATION
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation est
autorisĂŠe aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
www.plantronics.com
2014 Plantronics, Inc. All rights reserved
Plantronics, the logo design, and Sound Innovations
are trademarks or registered trademarks of Plantronics, Inc.
This equipment complies with IC radiation exposure limits set forth
for an uncontrolled environment.
Printed in U.S.A.
201528-01 (05.14)
Cet équipement est conforme aux limites d’exposition de radiation
IC ĂŠnoncĂŠs pour un environnement non contrĂ´lĂŠ.
CAN ICES-3 (B)/NMB-3(B)
LIMITED WARRANTY
• This warranty covers defects in materials and workmanship of
products manufactured, sold or certified by Plantronics that were
purchased and used in the United States.
• The warranty lasts for one year from the date of purchase of the
products.
• This warranty extends to you only if you are the end user with the
original purchase receipt.
• We will, at our option, repair or replace the products that do not
conform to the specification. We may use functionally equivalent
reconditioned, refurbished, remanufactured, pre-owned or new
products or parts.
• To obtain service in the U.S., contact Plantronics at 800-544-4660.
• THIS IS THE COMPLETE PLANTRONICS WARRANTY FOR THE
PRODUCTS.
• This warranty gives you speciic legal rights, and you may also have
other rights that vary from state to state. Please contact your dealer or
our service center for the full details of our limited warranty, including
items not covered by this limited warranty.
TECHNICAL ASSISTANCE
Visit our Web site at www.plantronics.com/support for technical support
including frequently asked questions, compatibility and accessibility
information. The Plantronics Technical Assistance Center (TAC) is also
ready to assist you on 800-544-4660.
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock, and injury to
persons, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product. The
symbol identifies and alerts the user to the presence of important
operating and service instructions.
3. Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not locate Base Unit near water, for example, near a bathtub or
sink, in a wet basement, or near a swimming pool.
5. This product should never be placed near or over a radiator or heat
register. This product should not be placed in a built-in installation
unless proper ventilation is provided.
6. This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of
power supply to your home, consult your dealer or local power
company.
7. Do not locate this product in an area where the power cord is likely
to be damaged by furniture or foot traffic.
8. Do not overload outlets and extension cords as this can result in the
risk of fire or electric shock.
9. Never push objects of any kind into this product through Base Unit
slots as they may touch dangerous voltage points or short out parts
that could result in a risk of fire or electric shock. Never spill liquid of
any kind on the product.
10. To reduce the risk of electric shock, do not disassemble this product,
but take it to qualified service personnel when service or repair
work is required. Opening or removing covers may expose you to
dangerous voltages or other risks. Incorrect reassembly can cause
electric shock when the product is subsequently used.
11. Avoid using telephone equipment during an electrical storm. There
may be a remote risk of electric shock from lightning.
12. Do not use the telephone equipment to report a gas leak in the
vicinity of the leak.
13. Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a) When the power supply cord or plug is damaged or frayed.
b) If the product has been exposed to liquid.
c) If the product does not operate normally by following the
operating instructions. Adjust only those controls that are covered
by the operating instructions because improper adjustments of
other controls may result in damage and will often require extensive
work by a qualified technician to restore the product to normal
operation.
d) If the product has been dropped or the Base Unit has been
damaged.
e) If the product exhibits a distinct change in performance.
14. Never install telephone wiring during a lightning storm.
15. Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.
16. Never touch uninsulated telephone wires or terminals unless the
telephone line has been disconnected at the network interface.
17. Use caution when installing or modifying telephone lines.
18. This product is intended to be supplied by a Listed Class 2 Direct
Plug-In Power Unit, rated at an output voltage of 9 VDC at 500mA.
19. This product requires AC power in order to operate. In order to
have phone service during a power outage, have another headset
available that is powered only by the communications equipment.
20. Keep all product cords and cables away from operating machinery.
BATTERY PACK PRECAUTIONS
CAUTION: To reduce the risk of fire or injury to persons, read and follow
these instructions.
• Use only the battery pack supplied with this product.
• Do not dispose of battery pack in a ire. The cells may explode. Check
with local codes for possible disposal instructions.
• Do not open or mutilate battery pack. Released electrolyte is corrosive
and may cause damage to eyes or skin and may be toxic if swallowed.
• Exercise care in handling the battery pack in order not to “short” the
battery contacts with conducting materials such as rings, bracelets,
and keys. The battery or conductor may overheat and cause burns.
• Charge the battery pack in accordance with instructions supplied with
this unit.
• Observe proper orientation between battery pack and charger contacts.
SUPPLIES & ACCESSORIES
N !"# $%&!'() *+# ,-./
E0!2-'"&1&)-2-'
3U'-43 %/-)-3
$0+"!)A')/5567897:
AC Adapters
64401-03
38640-01 (not shown)
(not shown)
N !"# $%&!'()
2;<=
Remote
201059-01
(DECT 6.0)
Countries outside
of North America
201059-02 (DECT)
Console Interface Cable 68331-01
6 wire, modular-to-PJ7 cable assembly
Please note that the older spare
Remotes (PNs 80323-01 and
80323-02) will not work with the
CA12CD-S
Connectors other than the PJ7 are
available upon request
Battery Pack
80322-01
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Create Date                     : 2014:06:10 16:37:50-07:00
Creator                         : Adobe InDesign CS5 (7.0)
Modify Date                     : 2014:06:17 13:00:11-04:00
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Instance ID                     : uuid:6879c56b-d513-4307-9421-32f81af602b1
Document ID                     : xmp.did:17D99B2BDF2068118C14D4ECE836782D
Original Document ID            : adobe:docid:indd:6003702c-15c9-11dc-abfb-e42676339c84
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:E31CB625DF2068118C14D4ECE836782D
Derived From Document ID        : xmp.did:1761A8E6742168118C14B79D8E0619BE
Derived From Original Document ID: adobe:docid:indd:6003702c-15c9-11dc-abfb-e42676339c84
Derived From Rendition Class    : default
History Action                  : saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved
History Instance ID             : xmp.iid:B3CDA95336226811871FED22071CA812, xmp.iid:B4CDA95336226811871FED22071CA812, xmp.iid:C937565638226811871FED22071CA812, xmp.iid:F796B2E03C226811871FED22071CA812, xmp.iid:C161350F3D226811871FED22071CA812, xmp.iid:5D8E7FC186226811871FED22071CA812, xmp.iid:AE8B5018422068118C14A368ED42ABEB, xmp.iid:30085CCC422068118C14A368ED42ABEB, xmp.iid:42703733452068118C14A368ED42ABEB, xmp.iid:EA69CD3C452068118C14A368ED42ABEB, xmp.iid:1294D03C452068118C14A368ED42ABEB, xmp.iid:1C94D03C452068118C14A368ED42ABEB, xmp.iid:C99800EF502068118C14A368ED42ABEB, xmp.iid:D46CA64D532068118C14A368ED42ABEB, xmp.iid:614465B8552068118C14A368ED42ABEB, xmp.iid:AA9F16B7642068118C14A368ED42ABEB, xmp.iid:AB9F16B7642068118C14A368ED42ABEB, xmp.iid:023AC815452068118C14DFC2C8B028B3, xmp.iid:9073507BFD2168118C1481E882F918F4, xmp.iid:5725D194FD2168118C1481E882F918F4, xmp.iid:76261F689221681192B0B19EA112EC17, xmp.iid:7BA0C9E8AF21681192B0B19EA112EC17, xmp.iid:26910F4CB021681192B0B19EA112EC17, xmp.iid:A716185EB121681192B0B19EA112EC17, xmp.iid:04A9837AB121681192B0B19EA112EC17, xmp.iid:05A9837AB121681192B0B19EA112EC17, xmp.iid:06A9837AB121681192B0B19EA112EC17, xmp.iid:CF192A540422681192B0B19EA112EC17, xmp.iid:881A4B780422681192B0B19EA112EC17, xmp.iid:FE6B9B12052768118C148EB47BA1D911, xmp.iid:75EBCB91302768118C148EB47BA1D911, xmp.iid:35196EC1322768118C148EB47BA1D911, xmp.iid:07B0B69E382768118C148EB47BA1D911, xmp.iid:19CD79B4382768118C148EB47BA1D911, xmp.iid:22CD79B4382768118C148EB47BA1D911, xmp.iid:B8AD883B392768118C148EB47BA1D911, xmp.iid:2ECB016D862768118C148EB47BA1D911, xmp.iid:E8CFADE98D2768118C148EB47BA1D911, xmp.iid:E9CFADE98D2768118C148EB47BA1D911, xmp.iid:F2CFADE98D2768118C148EB47BA1D911, xmp.iid:4D7DCE6F912768118C148EB47BA1D911, xmp.iid:BF9EBC950B2068118083A6BF97E4CF27, xmp.iid:D3F4C3EA152068118083A6BF97E4CF27, xmp.iid:FF7F11740720681192B0CD0D4803F969, xmp.iid:1E3526290B20681192B0CD0D4803F969, xmp.iid:88083BCD0D20681192B0CD0D4803F969, xmp.iid:6FC59A777A22681192B0CD0D4803F969, xmp.iid:59561B137D22681192B0CD0D4803F969, xmp.iid:57CFE8AA8022681192B0CD0D4803F969, xmp.iid:CF42B16B8222681192B0CD0D4803F969, xmp.iid:ADD887F59123681192B0CD0D4803F969, xmp.iid:A357BF929623681192B0CD0D4803F969, xmp.iid:E960D3FE9C23681192B0CD0D4803F969, xmp.iid:16022F7F712168118C14B79D8E0619BE, xmp.iid:1761A8E6742168118C14B79D8E0619BE, xmp.iid:63DAF40C752168118C14B79D8E0619BE, xmp.iid:27DB8BBD782168118C14B79D8E0619BE, xmp.iid:20260F32792168118C14B79D8E0619BE, xmp.iid:486580F07E2168118C14B79D8E0619BE, xmp.iid:8FC0E26D7F2168118C14B79D8E0619BE, xmp.iid:0E0AC8E6802168118C14B79D8E0619BE, xmp.iid:FEB8338C812168118C14B79D8E0619BE, xmp.iid:295EDABA812168118C14B79D8E0619BE, xmp.iid:BB94D2F5812168118C14B79D8E0619BE, xmp.iid:04BB00A0852168118C14B79D8E0619BE, xmp.iid:CA020B8C872168118C14B79D8E0619BE, xmp.iid:C5E7C3CF872168118C14B79D8E0619BE, xmp.iid:FF93F71A882168118C14B79D8E0619BE, xmp.iid:E4F01CDF8E2168118C14B79D8E0619BE, xmp.iid:46D18D638F2168118C14B79D8E0619BE, xmp.iid:8DADE66E8F2168118C14B79D8E0619BE, xmp.iid:1047AB798F2168118C14B79D8E0619BE, xmp.iid:D9F61674072068118C14D4ECE836782D, xmp.iid:C4D179AE082068118C14D4ECE836782D, xmp.iid:ACBE416F0E2068118C14D4ECE836782D, xmp.iid:95A0427C3F2068118C14D4ECE836782D, xmp.iid:971525863F2068118C14D4ECE836782D, xmp.iid:F845BEBA442068118C14D4ECE836782D, xmp.iid:4661BA0D6F2068118C14D4ECE836782D, xmp.iid:256F27E7762068118C14D4ECE836782D, xmp.iid:D9207B62B52068118C14D4ECE836782D, xmp.iid:FCA9C494B52068118C14D4ECE836782D, xmp.iid:E21CB625DF2068118C14D4ECE836782D, xmp.iid:E31CB625DF2068118C14D4ECE836782D, xmp.iid:17D99B2BDF2068118C14D4ECE836782D
History When                    : 2011:10:07 16:26:15-07:00, 2011:10:07 16:26:15-07:00, 2011:10:07 16:40:39-07:00, 2011:10:07 17:13:09-07:00, 2011:10:07 17:14:27-07:00, 2011:10:08 11:36:55-07:00, 2013:06:24 18:00:26-07:00, 2013:06:24 18:05:28-07:00, 2013:06:24 18:22:39-07:00, 2013:06:24 18:22:55-07:00, 2013:06:24 18:22:55-07:00, 2013:06:25 16:40:24-07:00, 2013:06:25 16:53:49-07:00, 2013:06:25 17:10:46-07:00, 2013:06:25 17:28:04-07:00, 2013:06:26 11:30:47-07:00, 2013:06:26 11:33-07:00, 2013:07:10 10:06:39-07:00, 2013:08:12 18:09:10-07:00, 2013:08:12 18:09:52-07:00, 2013:11:22 11:19:49-08:00, 2013:11:22 15:23:24-08:00, 2013:11:22 15:26:10-08:00, 2013:11:22 15:33:50-08:00, 2013:11:22 15:34:37-08:00, 2013:11:22 15:37:07-08:00, 2013:11:22 15:40:51-08:00, 2013:11:25 10:55:36-08:00, 2013:11:25 10:56:36-08:00, 2014:05:06 11:29:50-07:00, 2014:05:06 11:29:51-07:00, 2014:05:06 11:45:29-07:00, 2014:05:06 12:27:26-07:00, 2014:05:06 12:28:03-07:00, 2014:05:06 12:28:10-07:00, 2014:05:06 12:31:49-07:00, 2014:05:09 11:41:21-07:00, 2014:05:09 11:41:21-07:00, 2014:05:09 11:45:56-07:00, 2014:05:09 11:47:01-07:00, 2014:05:09 12:06:34-07:00, 2014:05:12 11:05:05-07:00, 2014:05:12 11:05:05-07:00, 2014:05:16 12:14:54-07:00, 2014:05:16 12:58:08-07:00, 2014:05:16 13:00:20-07:00, 2014:05:20 14:17:11-07:00, 2014:05:20 14:17:11-07:00, 2014:05:20 14:42:53-07:00, 2014:05:20 14:55:26-07:00, 2014:05:22 17:43:46-07:00, 2014:05:22 17:43:46-07:00, 2014:05:22 18:29:43-07:00, 2014:06:03 15:43:32-07:00, 2014:06:03 15:43:32-07:00, 2014:06:03 15:52:18-07:00, 2014:06:03 16:11-07:00, 2014:06:03 16:14:15-07:00, 2014:06:03 16:55:21-07:00, 2014:06:03 16:58:51-07:00, 2014:06:03 17:09:23-07:00, 2014:06:03 17:14:01-07:00, 2014:06:03 17:15:19-07:00, 2014:06:03 17:16:58-07:00, 2014:06:03 17:43:11-07:00, 2014:06:03 17:56:56-07:00, 2014:06:03 17:58:50-07:00, 2014:06:03 18:00:56-07:00, 2014:06:04 09:57:59-07:00, 2014:06:04 10:01:41-07:00, 2014:06:04 10:02-07:00, 2014:06:04 10:02:18-07:00, 2014:06:04 10:09:48-07:00, 2014:06:04 10:18:35-07:00, 2014:06:04 10:59:45-07:00, 2014:06:05 10:51:29-07:00, 2014:06:05 10:51:46-07:00, 2014:06:05 11:29:01-07:00, 2014:06:05 16:31:50-07:00, 2014:06:06 09:44:29-07:00, 2014:06:10 11:38:41-07:00, 2014:06:10 11:40:05-07:00, 2014:06:10 16:37:29-07:00, 2014:06:10 16:37:38-07:00, 2014:06:10 16:37:39-07:00
History Software Agent          : Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0
History Changed                 : /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata
Metadata Date                   : 2014:06:17 13:00:11-04:00
Creator Tool                    : Adobe InDesign CS5 (7.0)
Page Image Page Number          : 1, 2
Page Image Format               : JPEG, JPEG
Page Image Width                : 256, 256
Page Image Height               : 256, 256
Page Image                      : (Binary data 11414 bytes, use -b option to extract), (Binary data 12421 bytes, use -b option to extract)
Doc Change Count                : 1907
Format                          : application/pdf
Producer                        : Adobe PDF Library 9.9
Trapped                         : False
Page Count                      : 2
EXIF Metadata provided by EXIF.tools
FCC ID Filing: AL8-CA12CDSX

Navigation menu