Plantronics M70 Bluetooth Headset User Manual Bluetooth Headset 2013 10 15

Plantronics Inc Bluetooth Headset Bluetooth Headset 2013 10 15

Bluetooth Headset - User manual 2013.10.15

Wearing your headset, power it on. The first timeyou do, you will be prompted to select yourlanguage from a set of three options. Whencompleted, you will hear "pairing", go to the"settings" menu on your phone to connect to yourheadset.SELECT LANGUAGE1When the headset indicator lights flashes redand blueactivate Bluetooth® on your phone andset it to search for new devices.•iPhone* Settings > Bluetooth > On•Android™ Smartphones* Settings > Wireless &Networks > Bluetooth: On > Scan for devices2If necessary, enter four zeros (0000) for thepasscode or accept the connection.Once successfully paired, the indicator lights stops flashing.GET PAIRED TAKE CONTROL Answer or end a callTap the Call button .Decline a callPress the Call button for 2 seconds.Adjust the volumeTap the Volume up (+) or down (–) button.Mute onDuring a conversation, simultaneously tap theVolume (+) and (–) buttons. You will hear “muteon”, this voice alert will be repeated once. Afterthat an alert tone repeats every 15 minutes whenmute is on.Activate voice dial (phone feature)Press the Call button for 2 seconds, wait forthe phone prompt and then tell the phone to dialthe name of a stored contact.Change languageReselect the headset language at any time byputting your headset into pair mode.Press the Call button until the indicator lightflashes red and blue and you hear "pairing, pleaseselect a different language."RedialTo call your last number dialed, double tap theCall button .The universal-fit eartip has a thin loop that bendsto gently tuck into the contours of either ear. Toadjust the fit, you can rotate the eartip on theheadset or add the optional clip-on earloop. ADJUST THE FIT For the best voice pickup, always check that theheadset points toward the corner of your mouth. Your new headset has enough power to pair andmake a few calls. It takes 2 hours to fully chargethe headset; the indicator light turns solidblue once charging is complete.CHARGE
FCC statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF exposure warning · The equipment complies with FCC RF exposure limits set forth for anuncontrolled environment. The equipment must not be co-located or operating in conjunction with any other antenna or transmitter. NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
IC Radiation Exposure Statement for Canada This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
If you leave your headset powered on but out ofrange of your paired phone for more than 90minutes, your headset will conserve its batterypower by entering into a DeepSleep™ mode.Once back in range with your phone, tap the Callbutton to exit DeepSleep mode. If your phoneis also ringing, tap the Call button again toanswer your call.SAVE POWERYour headset tells you about status changes inEnglish. For example:“Power on”“Pairing successful”“Talk time (x) hours”“Mute on”"Incoming call""Answering call"“Lost connection”“Recharge headset”HEAR IT WHISPEROnce you have paired your two phones, it's easyto answer calls from either phone.When on a call, you will hear a ringtonenotification of an incoming call from the secondpaired phone. To answer the second call, youmust first end your current call (tap the Call button) so new call automatically answers.To pair a second phone or a new phone see"Change language" in the Take Control section.USE TWO PHONESBluetooth has a working “range” of up to 33 feet(10 meters) between the phone and headsetbefore audio degrades and the connection is lost.If you lose connection your headset will try toreconnect once you move back into range.For best audio reception, keep your phone andheadset on the same side of your body.STAY CONNECTEDIf your headset loses the Bluetooth® connectionwith your phone, it will automatically try toreconnect.If your headset can't reconnect, tap the Callbutton once or manually connect through thephone's Bluetooth device menu.If your headset remains out of range for morethan 90 minutes, the DeepSleep™ mode willactivate.KNOW HOW TO RECONNECTIf your phone also has the Bluetooth A2DP(Advanced Audio Distribution Profile) stereomusic feature, your music, podcasts, navigationand other streaming audio can be heard throughthis headset.Music TrackingWhile in A2DP mode you can adjust the volumeby tapping the Volume up or Volume downbutton. To skip tracks, press and hold the Volumeup or Volume down button until the track skipsforward or backward. To play/pause hold bothsides of the Volume button at the same time.LISTEN TO MUSIC AND MOREGET STARTEDM70 – M90 SERIES™Designed in Santa Cruz, CaliforniaFind a local support numberplantronics.com/supportRead detailed online user guideplantronics.com/documentationNEED MORE HELP?© 2013 Plantronics, Inc. All Rights Reserved. Bluetooth isa registered trademark of Bluetooth SIG, Inc. and any useby Plantronics is under license. All other trademarks arethe property of their respective owners. iPhone is atrademark of Apple, Inc.Patents US 5,712,453; Patents pendingpn200723-XX (08.13) am200274-XX

Navigation menu