Plantronics Savi 8200 Ug

User Manual: Plantronics Savi 8200 Series Manuals and Guides | Plantronics

Open the PDF directly: View PDF PDF.
Page Count: 21

Savi 8200 Series
Wireless Headset System
User Guide
Contents
DECT Information 3
DECT Enhanced Security 3
Overview 4
Base and Headset Basics 4
Accessories 5
Hook up your system 6
Desk phone setup details 6
Position Your Base 7
Fit and charge 8
Customize Your Headset 8
Charge Your Headset 8
Talk Time 8
Headset Battery Status 8
Pair your headset 9
Auto Connect Feature 9
Load software 10
The basics 11
Headset Controls 11
Power on your headset 11
Make, answer, end calls 11
Change your default phone line 12
Get a dial tone 12
Adjust volume 12
Mute 12
Transfer mobile audio 12
Audio streaming 12
ANC 12
Optimize audio quality 12
Mini conference call 12
Set up a conference call 12
Change voice prompt language 13
More Features 14
Base Subscription Button 14
Troubleshooting 16
Headset 16
Desk Phone 17
Mobile 17
Softphone 17
Appendix 19
Plantronics Hub configurable settings 19
System Requirements 20
Support 21
2
DECT 6.0 products should never be used outside the region in which they were originally
purchased and intended to be used.
The enclosed DECT 6.0 wireless product uses restricted wireless radio frequencies which vary by
country. DECT 6.0 devices are generally authorized for use in The Americas. Use of this DECT 6.0
product in unauthorized countries is a violation of law, may disrupt telecommunications networks
and devices, and can subject you to fines and penalties by regulatory agencies.
Plantronics is a member of the DECT Forum and has fully adopted their recommendations for
enhancements to security within all DECT products.
Plantronics DECT-based products now fully incorporate the latest recommendations on Enhanced
Security from the DECT Forum and ETSI. These improvements cover registration, authentication,
authorization and encryption procedures. Plantronics DECT products are now secure against all
the known vulnerabilities that were highlighted by the public announcements of the Chaos
Council in 2009.
Plantronics Savi 8200 Series DECT products have been tested against and passed the DECT
Forum security certification requirements and consequently have been granted 'DECT Forum
security' logo certification.
Plantronics products using the new enhanced version of DECT that includes these security
improvements are marked on the base with the DECT Forum security logo.
DECT Information
DECT Enhanced Security
3
Base
1 2 3 4
567
8 9 10
11 12 13 14
1Power jack 8Computer button
2Handset lifter jack 9Mobile phone button
3Telephone interface cable jack 10 Desk phone button
4USB port 11 Incoming call ringer
5Desk phone speaking volume 12 Bluetooth pairing button/LED
6Desk phone configuration switch 13 Subscription button/LED
7Desk phone listening volume 14 Charging LED
Headset
12
3
4
5
6
1Volume wheel 4Headset LED
2Call button 5Power button
3Mute 6ANC (Active Noise Canceling)
Be safe
Please read the safety guide for important safety, charging, battery and regulatory information
before using your new headset.
Overview
Base and Headset Basics
4
1Electronic hookswitch cable (EHS cable) Electronically and automatically answers/ends a desk
phone call. Enables remote call control with your headset.
2HL10 lifter Automatically lifts handset and returns it to the cradle. Enables remote call control
with your headset.
Accessories
5
Using the diagram, connect your headset system.
Choose a desk phone setup A, B or C and connect cables.
ADesk phone (standard)
USE
• Connect one end of the telephone interface cable to the back of the base
• Disconnect the handset coil cord from the base of the desk phone and re-connect it to the
telephone interface cable junction box.
• Finally connect the remaining end of the telephone interface cable into the open handset port
on the desk phone.
NOTE If your phone has a built-in headset port, you should only use the headset port if you will
not be using the HL10 lifter. In this configuration, you must press both the headset button on your
phone and the call control button on the headset to answer or end calls.
Hook up your system
Desk phone setup details
6
BDesk phone + EHS cable (sold separately)
See the user guide at plantronics.com/accessories for details.
USE
CDesk phone + HL10 lifter (sold separately)
See the user guide at plantronics.com/accessories for details.
USE
The minimum recommended separation between your desk phone and the base is 6 inches.
The minimum recommended separation between the base and computer is 12 inches. Incorrect
position can cause noise and interference problems.
Position Your Base
7
Optimize the comfort and fit of your headset.
Adjust the Headband
1To adjust the headband, lengthen or shorten the band until it fits comfortably. Position the
earcups so that the foam cushions sit comfortably over the center of your ears.
2Position the stabilizer T-bar above your ear, if applicable.
Adjust the Boom
For optimum audio, bend the boom so it is approximately two finger widths from the corner of
your mouth.
NOTE For true stereo listening when wearing the boom on the left, adjust the setting in Plantronics
Hub (plantronics.com/software) by going to Settings > Ringtones and Volumes > Wearing preference
for volume control.
Place the headset in the charge cradle. The headset charging LED flashes green when charging the
headset and turns solid green when the headset is fully charged. Charge for at least 20 minutes
prior to the first use. A full charge takes 3 hours.
With a single full charge, the headset provides up to 13 hours of continual talk time in wideband
mode.
There are 3 ways to determine your headset battery status.
• Listen to the voice prompts after powering on the headset
• Hover over the Plantronics Hub system tray icon
• Press the base subscription button; the base Audio buttons light up (solid green is high battery,
flashing green is medium, flashing yellow is low, flashing red is critical).
Fit and charge
Customize Your Headset
Charge Your Headset
Talk Time
Headset Battery Status
8
1To pair your base and mobile phone, first power on your headset. Press and hold the Bluetooth
pairing button on the base for 4 seconds until the Bluetooth LED flashes red and blue.
NOTE Your base and headset are automatically paired/subscribed.
2Go to Bluetooth settings on your mobile phone and select PLT Savi. Once successfully paired, the
Bluetooth LED on the base turns solid blue.
Once you have paired and connected your mobile phone to the base, the base automatically
connects to it when you are in range of your base.
To manually disconnect/connect your mobile phone from the base, press the base Bluetooth
button.
You may customize this feature in Plantronics Hub Settings > Wireless > Auto Connect to Mobile
Phone.
Pair your headset
Auto Connect Feature
9
Plantronics Hub for Windows/Mac is an invaluable resource to change
settings, update firmware, change your headset language and more.
1Download Plantronics Hub for Windows/Mac by visiting plantronics.com/software.
2Manage your headset settings on your computer with Plantronics Hub:
• Call control for softphones
NOTE Some softphones require the installation of Plantronics Hub for Windows/Mac to enable
headset call control (answer/end and mute) functionality.
• Change headset language
• Update firmware
• Turn features on/off
• View user guide
Load software
10
12
3
4
5
6
1Volume wheel Rotate volume wheel to adjust volume
2Call button Press to place, answer, end a call
3Mute button During a call, press to mute and unmute
4Headset LED Flashes when in use
5Power button Toggle on and off
6ANC (Active Noise Canceling) Toggle on and off
To turn on the headset, slide the Power button on the bottom of the earcup to reveal green.
On the top of the base there are three Audio buttons: computer, mobile, desk phone. These
buttons allow you to switch to a different phone line/audio channel.
Make a call
1Tap an Audio button on the base.
2Deskphone only: Manually remove the handset if you don't have an HL10 lifter or EHS cable. You
should hear a dial tone.
TIP If you do not hear a dial tone, open the base side panel and adjust the middle switch (A--G). “A”
works for the majority of desk phones.
3Dial from your softphone/mobile phone/desk phone.
Answer/end a call
To answer or end a call, tap the Audio button on the base or tap the headset Call button.
TIP Headset call control for the computer requires Plantronics software and softphone compatibility.
See “Download software.”
Answer a second call
1While on a call, press the headset Call button for 2 seconds to answer the second call.
This will place the first call on hold.
2To switch between the calls, press the headset Call button for 2 seconds.
Reject a Mobile Call
To reject an incoming call, hold the base mobile button down for 3 seconds.
The basics
Headset Controls
Power on your headset
Make, answer, end calls
11
With the system idle, change your default phone line/audio channel by pressing and holding for 4
seconds the desired base Audio button until it flashes green 4 times. Customizable in Plantronics
Hub also.
To open an audio channel or get a dial tone, press the headset Call button for 1 second while the
system is idle; the default base Audio button turns green.
•Headset volume Fine-tune your headset volume by adjusting the volume wheel.
•Desk phone volume When you are on a desk phone call and your voice is too quiet/loud, adjust
the microphone volume on the side of the base, located behind the access panel. If your caller's
voice is too loud/quiet on a desk phone call, adjust the base volume dial.
•Base ringtone volume Adjust the base ringtone volume on the left side of the base. This ringtone
alerts you if you are not wearing your headset and a call comes in.
To mute your headset during on a call, press the headset Mute button. When mute is active, the
base button is red. To unmute, press the headset Call button or the active base Audio button.
When you answer a call, the audio stays with that device (if you answer with the headset, the
audio stays on the headset; answer with your mobile phone, the audio stays on your mobile).
1To transfer a mobile call from your headset to your mobile phone, press the base mobile phone
button for 3 seconds. The green LED turns off.
2To transfer a mobile call from your mobile phone to your headset, press the base mobile phone
once. The green LED turns on.
To stream audio from your computer or mobile device, first press the computer or mobile base
Audio button and then play the audio. When streaming audio, the base Bluetooth button is purple.
Active Noise Canceling (ANC) reduces external noise and enhances your music and sound quality.
Your headset ships with ANC on. To turn ANC off, slide the switch away from "ANC."
There are 3 audio modes: wideband stereo (default), wideband (high quality telephony) and
multimedia (high quality listening).
To optimize your audio quality for your activity, with the system idle, press the headset Mute
button for 4 seconds. The base cycles through the modes with each 4 second press. The base
blinks yellow for wideband stereo, green for wideband and red for multimedia mode.
Simultaneously hold the base buttons of any two of the three base buttons until the LEDs become
solid green to combine the audio of any two devices and create a mini conference call.
You can set up a conference call with 4 additional headsets.
Join similar Savi headsets
1While on a call, place the guest headset into the primary user's charge cradle.
The base subscription LED flashes yellow and green.
2The primary user will hear a request "Conference requested." To accept the request, press the
primary user's headset Call button. The base subscription LED turns solid yellow to indicate
conference call mode. View conference call status by going to Plantronics Hub About >
Connections > Conferenced headsets.
Join different Savi headsets
Change your default
phone line
Get a dial tone
Adjust volume
Mute
Transfer mobile audio
Audio streaming
ANC
Optimize audio quality
Mini conference call
Set up a conference call
12
1While on a call, press the base subscription button.
The base subscription LED flashes yellow and green.
2Next press the guest headset volume up button until the headset LED turns on.
3The primary user will hear a request "Conference requested." To accept the request, press the
primary user's headset Call button. The base subscription LED turns solid yellow to indicate
conference call mode. View conference call status by going to Plantronics Hub About >
Connections > Conferenced headsets.
Exit a conference call
1Guest headsets can remain as guests through multiple calls. To remove a guest headset, either
press the guest headset's Call button or dock the primary user's headset in the charge cradle.
1To change the voice prompt language on your headset, directly connect your headset to your
computer via a USB/USB-C cable (do not dock it in the base cradle).
2Open Plantronics Hub and go to Settings > Language
You can choose from: Cantonese, Danish, English (UK, US), French, German, Indonesian, Italian,
Japanese, Korean, Mandarin, Norwegian, Russian, Spanish, Swedish and Thai.
Change voice prompt
language
13
The headset and base that came in the box are subscribed (connected) to each other. However, if
you wish to use a new headset or need to restore subscription to your current headset (base
subscription button is red), the units can be subscribed to each other by the following methods.
The subscription button is below the Bluetooth button on the front of the base.
Base Subscription Button LED
Base Subscription LED Base Status
Flashes green and red Primary headset subscription mode
Solid green Primary headset subscribed to base
Solid yellow Active conference call with guest headsets
Solid red No headset subscribed
Flashes green 3X, the yellow 2X Security level changed from enhanced to standard
Set the Range
Changing the range can help with desk phone/PC audio quality, improve user density or restrict
range of users.
You can change the range using the subscription button on the base. With the system idle, press
the subscription and desk phone buttons for 3 seconds. With each 3 second press the desk phone
button will cycle through ranges: green for high range, yellow for medium and red for low.
Setting Range
High (Default) (green) up to 350 ft.
Medium (yellow) up to 150 ft.
Low (red) up to 50 ft.
You can also adjust the range setting in Plantronics Hub Settings > Wireless. > Range.
Automatic secure subscription
With your system idle, docking a new headset automatically subscribes it to the base, making it
the primary headset. The base subscription LED blinks green/red during subscription mode and
remains green when the new subscription is established.
Manual secure subscription
With your system idle and your headset docked, double press the subscription button on the base.
The subscription light will flash red and green. When the subscription light on the base becomes
solid green, the headset and base are subscribed to one another.
Manual over-the-air subscription
1With your system idle and your headset undocked, double press the subscription button on the
base. The subscription light will flash green and red.
2Press the headset Call button up for 4 seconds; you hear "pairing." Upon release, the headset LED
flashes red/green. When the subscription light on the base remains solid green, the headset and
base are subscribed to one another; you hear "pairing successful. Base connected."
More Features
Base Subscription Button
14
NOTE If the base subscription LED goes solid red, after flashing red/green, the subscription attempt
has failed and should be repeated.
End Subscription
If the base is in subscription mode and you want to stop the base from searching for a headset,
press the subscription button again. The subscription light will be solid red for four seconds and
then go to its previous state.
Disabling Over-the-Air Subscription
The Savi system ships with the over-the-air headset subscription enabled. In a multi-shift
environment, you may want to disable this mode of subscription.
To disable over-the air subscription, while your system is idle, hold the subscription button and the
base computer button down simultaneously until the base computer button LED flashes (green for
enabled, red for disabled).
You can also adjust the over-the-air subscription setting in Plantronics Hub Settings > Wireless. .
Subscription and Security Levels
Your Savi 700 Series headset system (v28 or later) supports DECT Forum recommendations for
"Enhanced Security". Products with Enhanced Security are marked with the DECT Forum security
logo on the base.
Both your headset and headset base are compatible with older (prior to v28) headset bases and
headsets supporting older versions of DECT. Below is helpful information if you plan to use
Enhanced Security and older DECT components together.
If your Enhanced Security headset or headset base is subscribed with an older headset or headset
base, the resulting security level for the mixed headset and base combination will be set to the
level of the older headset for all calls. This is because older system components are not able to
support Enhanced Security.
All subscription details above apply when subscribing an Enhanced Security headset to an older
base, or visa versa, however there are unique system alerts indicating that the system is changing
the security level from Enhanced Security to the older version of security.
If an older headset is subscribed to an Enhanced Security Base:
• The subscription LED (lower left) will flash GREEN 3 times followed by YELLOW 2 times. This flash
pattern repeats 2 times.
If an Enhanced Security headset is subscribed to an older base:
• The Enhanced Security headset will play a security notification tone.
• The mono-colored LED on the headset will flash 3 times, then 2 times. This flash pattern is
repeated 2 times.
15
My headset is unstable. When you wear the headset, the microphone should rest as close
to your cheek as possible without touching. The microphone can
be adjusted inward by the pivoting earpiece to optimize the
position of the headset. See Position Your Headset.
Talk time performance is
significantly degraded even after a
full recharge.
Battery is wearing out. Contact us at plantronics.com/support .
I can’t hear a dial tone in the
headset. Make sure your headset is charged.
Make sure your headset is subscribed to base. See Base
Subscription.
Press the base desk phone button.
Make sure the lifter is lifting the handset high enough to operate
the hookswitch; set to a higher setting if necessary.
Adjust the configuration switch on the base until a dial tone is
heard. The default A works for most phones. See Make a Desk
Phone Call.
Fine tune the listening volume with the headset call control button.
See Adjust Your Headset Volume.
If the volume is still too low, adjust the desk phone listening
volume on the base. See Adjust Your Headset Volume.
I hear static. Make sure there is at least 12 inches between your base and your
computer, and 6 inches between your base and your telephone. If
adjusting the distance doesn’t help, your headset is going out of
range, move closer to the base. See Position Your Base.
The sound is distorted. Lower the desk phone speaking volume and/or desk phone
listening volume on the base. For most telephones the correct
setting is position 3. See Adjust Your Headset Volume.
If your desk phone has a volume control, lower until the distortion
disappears.
If the distortion is still present, adjust the headset volume control
to lower the headset speaker volume. See Adjust Your Headset
Volume.
Make sure there is 12 inches between your base and your
computer, and 6 inches between your base and your telephone.
See Position Your Base.
I hear echo in the headset. Lower the desk phone speaking volume and/or desk phone
listening volume on the base. For most telephones the correct
setting is position 3. See Adjust Your Headset Volume.
If the audio level is too low in this position, increase the headset
volume. See Adjust Your Headset Volume.
If your speaking volume is too low for your listener in this position,
adjust the position of the headset to make sure the microphone is
as close as possible to your mouth.
Adjust the configuration switch on the base until a dial tone is
heard. The default A works for most phones. See Make a Desk
Phone Call.
Troubleshooting
Headset
16
People I talk to can hear a buzz in
the background. Move the base further away from your phone. See Position Your
Base.
If the base power supply is plugged into a power strip, plug it into
the wall directly.
The handset lifter is installed but
does not lift the handset.
Be sure the handset lifter power cord is firmly pushed into the
handset lifter jack on the base.
Pairing problems Ensure the Bluetooth LED on the base flashes red and blue by
pressing the Bluetooth button for four seconds.
Ensure the Bluetooth mobile phone is in search mode.
When an active Bluetooth connection has been made, the base
Bluetooth LED is solid blue.
Why doesn’t the base automatically
reconnect with my mobile phone? Ensure Plantronics Hub software had been installed.
Adjust the "Auto-connect to mobile phone" in Plantronics Hub
Settings > Wireless. Make sure that "Never" is not selected.
When I dial from my softphone
application, nothing happens. Ensure your headset is charged.
Ensure your headset is subscribed to the base. See Subscribing a
Headset.
Ensure that the Plantronics software is installed. To download, visit
plantronics.com/software.
Ensure that you are using a compatible softphone application. For
a list of compatible softphones, visit plantronics.com/software.
If the Plantronics software is not installed and you do not have a
compatible softphone, you must first press the base computer call
button and then use the softphone interface to place/answer/end
calls.
Ensure that the headset is the default sound device by going to
your Sound Control Panel (Windows) or your Sound System
Preferences (Mac).
Restart your computer.
Speaking and/or listening volume is
too low or too high. Adjust headset listening volume with volume button.
Adjust listening/speaking volumes in the computer’s sound control
panel/system preferences.
Adjust listening/speaking volumes in the softphone application.
The sound is distorted or I hear an
echo in the headset. Reduce speaking and/or listening volume on the computer using
your softphone application.
Point microphone towards your chin.
If the distortion is still present, lower the volume on the headset.
I can no longer hear any audio
through my PC Speakers.
For Windows XP systems
Desk Phone
Mobile
Softphone
17
• Go to Start > Control Panel > Sounds and Audio Devices > Audio >
Sound Playback and change the default setting from your Savi
headset to your PC speakers. Click “OK” to confirm your change.
For Windows Vista and Windows 7 systems
• Go to Start > Control Panel > Sounds > Playback and change the
default setting from your Savi headset to your PC speakers. Click
“OK” to confirm your change.
For Mac OS X
• Choose Apple menu > System Preferences and click Sound.
• Click Output, and then select “Internal Speakers” or your speaker
choice.
No audio connection to PC. Unplug USB and power cables from base. Reconnect power cable
first. Wait for power LED to illuminate, then re-connect USB cable.
Quit and then re-start your PC audio or softphone application.
18
Feature Location
Answering Call Alert General
Audio channel tone General
Audio sensing General
Close conversation limiting General
Default phone line General
Online indicator General
Second incoming call General
Headset to PC radio link General
Plantronics product improvement program General
Software log level General
Change language
Brazilian Portugese, Cantonese, Danish, English (UK, US), French, German, Indonesian,
Italian, Japanese, Korean, Mandarin, Norwegian, Russian, Spanish, Swedish and Thai.
Answering call Base connected/
disconnected/not connected
Battery high/
medium/low
Call ignored Connection failed Conference requested/
failed
Guest exited
conference
Mute on/off/Muted No number available
Pairing/Pairing
incomplete
Phone connected/
disconnected
Power on/off
Recharge headset Volume maximum/minimum
Language
Desk phone ringtone Ringtone and Volume
PC ringtone Ringtone and Volume
Mobile phone ringtone Ringtone and Volume
Volume level tones Ringtone and Volume
Wearing preference for volume control (stereo audio) Ringtone and Volume
Ring location Ringtone and Volume
Dial tone Softphones
Target softphone Softphones
Media player action on incoming call Softphones
Softphones and media players (PLT enabled) Softphones
Software settings (Aware for Microsoft) Sensors and Presence
Audio quality Wireless
Auto connect to mobile phone Wireless
Bluetooth Wireless
Mobile voice commands Wireless
Over-the-air subscription Wireless
Range Wireless
Anti-startle Advanced
Noise exposure Advanced
Appendix
Plantronics Hub
configurable settings
19
Computer
• Supported Operating Systems: Windows® 7, Windows® 8, 8.1 and Windows 10; Mac OS X El
Capitan, Mac OS X Sierra, Mac OS X High Serra, Mac OS X 10.11 and Mac OS X 10.13, Mac OS X
Mojave
• Processor: 400 MHz Pentium® processor or equivalent (Minimum); 1 GHz Pentium processor or
equivalent (Recommended)
• RAM: 96 MB (Minimum); 256 MB (Recommended)
• Hard Disk: 280 MB (Minimum); 500 MB or more (Recommended)
Display
• At least 800 x 600, 256 colors
• 1024 x 768 high color, 32-bit (Recommended)
Browser
• Internet Explorer® V10 or better must be on the user’s system (Required)
Google Chrome™
System Requirements
20
Support
NEED MORE HELP?
plantronics.com/support
habitatsoundscaping@plantronics.com
Plantronics, Inc. Plantronics B.V.
345 Encinal Street
Santa Cruz, CA 95060
United States
Scorpius 171
2132 LR Hoofddorp
Netherlands
© 2018 Plantronics, Inc. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth, SIG, Inc. and any use of such marks by
Plantronics, Inc. is under license. All other trademarks are the property of their respective owners.
Patents pending.
212206-06 (09.18)

Navigation menu