Plantronics Voyager 5200 Ug
User Manual: Plantronics Voyager-5200-ug Voyager 5200 Series Manuals and Guides | Plantronics
Open the PDF directly: View PDF 
.
Page Count: 18
| Download | |
| Open PDF In Browser | View PDF |
Voyager 5200 Series Wireless Headset System User Guide Contents What's in the box 3 Accessories 4 Headset Overview 5 Charge your headset 6 Check Battery Level 7 Low battery warnings 7 Use charge case Fit 8 9 Pair your phone 10 Pair to mobile device 10 NFC pairing 10 Pair another device 10 The Basics 11 Make/Take/End Calls 11 VPA (Virtual Personal Assistant) 12 Mute 12 Mute on reminder* 12 Adjust the volume 12 Use Sensors 12 Pause or restart streaming audio 13 Advanced features 14 Voice alerts list 14 Adjust voice alert volume Specifications 15 14 Firmware Update 16 Headset recovery 16 Troubleshooting 17 2 What's in the box Headset Micro USB cable Eartips (S, M. L) 3 Accessories Sold separately at plantronics.com/accessories. Vehicle power charger Eartips with foam covers USB Bluetooth adapter Charge case Wall charger 4 Headset Overview C NF Charge port Call button Bluetooth button (use when pairing a device) Virtual Personal Assistant (VPA) button Mute button Volume buttons Indicator light Power button NFC Near Field Communication 5 Charge your headset Your new headset has enough power to pair and make a few calls directly out of the box. It takes approximately 90 minutes to fully charge the headset; the indicator light turns off once charging is complete. A micro USB cable is supplied to allow you to charge the headset with an AC wall charger (not included) or through a PC's USB port. The PC must be powered on to charge via USB 2.0 or higher. NOTE Always charge at near room temperatures; never charge battery at temperatures below 0°C (32°F) or above 40°C (104°F). 6 Check Battery Level There are multiple ways to check the battery level of the headset: • Listen to a voice prompts on the headset. • Check the LED indicators on the headset or charging case. • Use the Plantronics Hub application. Use the Plantronics Hub application for desktop or mobile. You can download the software by visiting plantronics.com/software Headset LED behavior Off Charging complete Battery high Battery medium Battery low Battery critical Low battery warnings Battery Level Voice Prompt 30 minutes of talk time remaining "Battery Low" repeats every 15 minutes 10 minutes of talk time remaining "Recharge Headset" every 5 minutes 7 Use charge case A fully charged case can recharge your headset fully two times for an additional 14 hours of headset talk time. IMPORTANT The charge case is placed in deep sleep mode after manufacturing to save power and protect the battery. To wake-up the charge case, plug it into a power source for a minimum of 1 minute. The LED's flash when charging. Check the charge case battery status by pressing the button on the side. Battery status LEDs for charge case Battery high Battery medium Battery low Battery critical; Recharge case/headset NOTE Charge case is sold separately. Visit plantronics.com/accessories for more information. 8 Fit 1 Slide headset over and behind your ear, then press gently toward your ear. NOTE Remove your eyeglasses before donning the headset for best fit. 2 Rotate microphone boom until it is pointed toward your mouth. 3 Mic boom moves up and down for a better fit. 1 2 3 Change the eartip for a better fit. 1 Push in eartip and rotate to the left to unlock it. 2 1 2 Align new eartip into slot; push, rotate to the right and lock into place. To wear the headset on your other ear, rotate the boom upwards then twist it around so the eartip is on the other side before lowering the mic boom. 1 3 2 9 Pair your phone Pair to mobile device 1 2 The first time you power on the headset it begins the pairing process. Put on your headset and you will hear "pairing" and the headset LEDs flash red and blue. Activate Bluetooth on your phone and set it to search for new devices. • iPhone Settings > Bluetooth > On* • Android Settings > Bluetooth: On > Scan for devices* NOTE *Menus may vary by device. 3 Select “PLT V5200 Series.” If necessary, enter four zeros (0000) for the passcode or accept the connection. Once successfully paired, you hear “pairing successful” and the headset LEDs stop flashing. NOTE Your headset can pair with up to 8 devices but only maintain 2 connections simultaneously; this includes the Bluetooth USB adapter. NFC pairing Pair another device NFC pairing is an option to pair your phone if there are one or less devices already connected. NFC pairing will not work if there are two devices connected already. 1 Ensure NFC is on and your phone’s display is unlocked. (Phones may vary.) 2 With the headset powered on, lay the headset on the back of phone near the NFC tag on phone as shown until NFC pairing completes. If necessary, accept the connection. 1 With the headset powered on press and hold the Call 2 While the headset LEDs are flashing blue and red, activate Bluetooth on your phone and set it to search for new devices. button until you hear "Pairing." 3 Select “PLT V5200 Series.” Once successfully paired, indicator lights stop flashing and you hear "pairing successful." 10 The Basics C NF Make/Take/End Calls • • • Answer a call Put the headset on to answer a call, or Say “answer” after call is announced, or Tap the Call button. • End a call Tap the Call button. • Reject incoming call Press the Call button for 2 seconds. • Redial last outgoing call Double-tap the Call button. 11 Caller Announcement (mobile phone only) When wearing your headset, you will hear the name of a contact calling so you can decide whether to answer or ignore the call without having to check the phone screen. An incoming caller name is announced: • if your phone supports Phone Book Access Profile (PBAP) • if you granted access to your contacts during pairing process (for many mobile phones, this is preset out-of-the box and may not be necessary) • if the caller is stored in the phone's contacts list An incoming caller name is not announced: if the caller is unknown, unlisted, blocked, or the language is not supported. VPA (Virtual Personal Assistant) • Voice control (Siri, Google Now, Cortana) Press and hold the red button for voice control. You will hear your smartphone voice engine when it is ready. Android mobile devices may require additional configuration for virtual personal assistant features. Please reference your carrier and device manufacturers's instructions to successfully utilize voice. Mute Mute on reminder* During a conversation, press the Mute button . You hear “mute on” or “mute off." An alert repeats every 15 minutes when mute is on. * Plantronics Hub for Mac/Win or Plantronics Hub for iOS/Android required to enable. (plantronics.com/software) You can add a mute alert notification by managing your mute feature with Plantronics Hub. If this setting is enabled and you have muted an active call and you start to speak, an alert will remind you that you are still on mute. Adjust the volume Use Sensors Press the Volume buttons up (+) or down (–) during a call or while streaming audio. While not on a call or streaming audio you can press the Volume buttons to adjust the volume level for Caller Announce and other voice prompts. Smart sensors in this headset recognize if the headset is being worn and can automatically perform time-saving functions. Putting on your headset will: • Answer an incoming call • Transfer an active call from your phone • Resume streaming audio Taking off your headset will: • Transfer an active call to your phone • Pause streaming audio 12 Reset Sensors You may need to reset the sensors if they are not working as expected. • • • • Pause or restart streaming audio • Wearing the headset, tap the Call button to test sensors. A talk time voice alert means sensors are working. A tone or lack of voice prompts means sensors need to be reset. To reset the sensors, power on headset, connect the headset to a charger or directly to your computer's USB port and place it on a flat, non-metallic surface for more than 10 seconds. If you don't have your charging cable available you can also reset your sensors by first turning off the headset, then pressing and holding the Call and Mute buttons simultaneously until the LED turns off. Then put on your headset and turn it on. Disable sensors You can disable your headset smart sensors through Plantronics Hub software under the Settings menu or in an idle state, simultaneously press and hold the call and mute buttons for 5 seconds and a voice prompt will inform you of smart sensors status. Press and hold the Call button for 2 seconds to either pause or restart playback. 13 Advanced features Voice alerts list Following is a list of common voice alerts, you can use Plantronics Hub to customize the alerts. Download Plantronics Hub at plantronics.com/software • "Answering call" • "Battery low" • "Redialing last outgoing call" • "Incoming call" • "Mute on/off/muted" • "No phone is connected" • "Pairing" • "Pairing incomplete, restart headset" • "Pairing successful" • "Power on/off" • "Phone X connected/disconnected" • "Recharge headset" • "Smart sensors on/off" • "Talk time X hours" • "Volume maximum/minimum" Adjust voice alert volume Toggle the volume button when the headset is powered on and idle (not on a call or streaming music) to adjust the volume of the headset's voice alerts. 14 Specifications Talk time Up to 7 hours talk time without using case; Up to 14 hours additional talk time using fully-charged case. NOTE Charge case is sold separately. Visit plantronics.com/accessories for more information. Bluetooth Version 4.1 Standby time Up to 9 days Weight 20 grams Smart sensor technology Dual capacitive sensors wearing status Noise cancelling • Four-mic active Digital Signal Processing (DSP) • Acoustic echo cancellation • Sidetone detection Water resistance P2i nano-coating on headset to repel moisture NFC pairing` Touch headset to NFC-enabled phones to complete pairing process Operating distance (range) 98 feet, 30 meters Bluetooth profiles Advanced Audio Distribution Profile (A2DP),Phone Book Access Profile (PBAP), Audio/Video Remote Control Profile (AVRCP), Wideband Hands-free (HFP) Profile 1.6 and Headset (HSP) Profile 1.2 Mulltipoint technology Connect two Bluetooth devices and answer calls or stream media from either device Battery type Rechargeable, non-replaceable lithium-ion polymer Charge connector Micro USB charging on headset Headset battery meter Automatically shows on-screen for iPhone and iPad. With Plantronics Hub for iOS/Android this shows on your smartphone screen Charge time (maximum) 90 minutes for full charge Operating and storage temperature 32°F – 104°F (0 – 40°C) NOTE * Performance is dependent upon battery and may vary by device. 15 Firmware Update Firmware updates are designed to keep your headset current with the latest technology. Update your firmware to: • Change voice alert/command languages • Improve performance • Add new features to your device You can update your headset wirelessly using either your smartphone or your desktop PC with Plantronics Hub. Download at plantronics.com/software With Plantronics Hub for Android/iOS installed on your smartphone, check Settings to see if an update is available. With Plantronics Hub for Windows/Mac installed on your computer, check Updates to see if a new version of firmware is available for your device. Tips • If you are preforming an update using Plantronics Hub from your phone: • Remove your headset from your ear. Do not use your headset or smartphone until the update is complete. • Disconnect your headset from other devices such as phones, tablets and computers. • Do not start a second update from a second phone. • Do not play music on your phone during the update. • Do not answer or place a call during the update. NOTE If you receive a lot of calls, emails or texts that interrupt your update, try turning on the Do Not Disturb feature in your phone's setting while you update. • If you are preforming an update using Plantronics Hub for [Windows] from your computer using your wireless Bluetooth adapter: • Remove your headset from your ear. Do not use your headset or computer until the update is complete. • Disconnect your headset from other devices such as phones, tablets and computers. • Do not start a second update from another device such as a phone or another computer. • Disconnect other Bluetooth headsets from your computer. • Do not answer or place a call during the update. Headset recovery If you receive an over the air update failure message, or experience an update failure, take the following steps: • Connect your headset to your computer. • Download and install Plantronics Hub for Windows/Mac at plantronics.com/product/plantronicshub-desktop • Open Plantronics Hub, go to Help > Support > Firmware Updates & Recovery and enter your Product ID (PID) to complete the recovery. 16 Troubleshooting Callers can't hear me. Solutions: • Ensure headset is paired and connected to your phone. • Reposition headset on your ear as the sensors may not detecting it is on. • Reset your sensors (following above instructions) as they may need recalibrating. • Disable your sensors as they may be incompatible with your specific ear shape. • Disable HD Voice (Wideband Audio) via Plantronics Hub application as this setting may be incompatible with your phone. I can't hear callers or music. Solutions: • Ensure headset is paired and connected to your phone. • Reposition headset on your ear as the sensors may not detecting it is on. • Reset your sensors (following above instructions) as they may need recalibrating. • Disable your sensors as they may be incompatible with your specific ear shape. My headset will not report 7 hours Solutions: of talk time after it is fully charged. • Ensure headset is paired and connected to your phone. • Disable HD Voice (Wideband Audio) which uses more power. • Completely discharge your headset's battery then give it a full charge. • Some phones have less efficient Bluetooth connections and thus will not allow for an optimal talk time of 7 hours. The talk time remaining estimate is partly calculated by your historical use so inconstancies in an estimate may occur based on your particular use patterns. 17 NEED MORE HELP? plantronics.com/support Plantronics, Inc. Plantronics BV 345 Encinal Street South Point Building C Santa Cruz, CA 95060 Scorpius 140 United States 2132 LR Hoofddorp, Netherlands © 2016 Plantronics, Inc. Plantronics and Voyager are trademarks of Plantronics, Inc. registered in the US and other countries, and Plantronics Hub and PLT are trademarks of Plantronics, Inc. Bluetooth is a registered trademark of Bluetooth SIG, Inc. and any use by Plantronics, Inc. is under license. The Apple logo and iPhone are trademarks of Apple, Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc. The trademark "iPhone" is used with license from Aiphone K.K. in Japan. Android, Google Now, Google Play and the Google Play logo are trademarks of Google Inc. All other trademarks are the property of their respective owners. Patents: US 8,208,673; 8,504,629; 8,805,992 patents pending 207276-06 (04.16) MODEL ID: POTE16
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Create Date : 2016:04:15 16:27:22-04:00 Creator : AH XSL Formatter V6.2 MR4 for Windows (x64) : 6.2.6.18551 (2014/09/24 15:00JST) Modify Date : 2017:11:16 16:22:26Z Language : EN XMP Toolkit : Adobe XMP Core 5.6-c137 1.000000, 0000/00/00-00:00:00 Physicalheightininches : 11.0 Physicalwidthininches : 8.5 Product ID : prod8080003 Num Pages : 18 Extracted : 2017:10:18 14:09:51.067-04:00 Sha 1 : 3d552afaa6c528bb22d9dab65ab5f48d82527caa Size : 1501067 Creator Tool : AH XSL Formatter V6.2 MR4 for Windows (x64) : 6.2.6.18551 (2014/09/24 15:00JST) Metadata Date : 2016:04:15 12:36:46.000-07:00 Format : application/pdf Modified : 2017:11:01 11:56:41.185-04:00 Document ID : uuid:7a20c75e-f727-4b09-8bbf-65a1fbfaa059 Instance ID : uuid:04294159-6103-4482-9430-b524460f64f6 Producer : Antenna House PDF Output Library 6.2.609 (Windows (x64)) Trapped : Unknown (false) Product Reference : /etc/commerce/products/plantronics/voyager/voyager-5200 Page Mode : UseOutlines Page Count : 18EXIF Metadata provided by EXIF.tools