Plastoform JB100 JAYBIRD BLUETOOTH STEREO HEADSET User Manual Jaybird Manual 2 indd

Plastoform Industries Ltd. JAYBIRD BLUETOOTH STEREO HEADSET Jaybird Manual 2 indd

USERS MANUAL

JB-100JayBird Bluetooth® Stereo HeadsetFreedom to rock while you playJB-100Federal Communication CommissionThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. IMPORTANT INFORMATION REQUIRED BY THE FCC THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
Warranty 1 Year parts and laborFAQ / TroubleshootingQ: I have trouble getting the headset on in a comfortable, sure fit position.A: Stand in front of a mirror while following the steps in section “Wearing your JayBird Bluetooth Stereo Headset”, making particular care that the in-ear buds are in their default 10 and 2 o’clock positions, and the behind-the-head wire is under your hair and sits against your neck below your hairline.Q: I have trouble knowing when my headset is connected to my device because I can’t see the LED light due to the headset being on my head.A: Always pair your device with the headset in your hand so you can see the LED status lights.Q: The sound quality is poor and sounds distortedA: Adjust the volume control on your device to a lower setting. Find the right balance between both volume controls on the device and headset for optimal sound performance.Q: The sound cuts in and out intermittently.A: While the range of Bluetooth is 10 meters (33 feet), the optimal range is within 2 feet of the device, particularly outdoors when the signal cannot bounce off walls and ceilings. Make sure your device is above your elbow and on your right side for optimal connectivity to your headset while streaming music outdoors.Q: Phone shows Bluetooth connection to headset, but no longer plays music through the headset after a temporary cut in connection.A: Close the streaming music program on your device and launch it again to reestablish the streaming music connection to the headset.Certification and Agency ApprovalsTable of Contents:What’s included in this package? 1Product Features 2Charging your headset 2Wearing the JayBird Bluetooth® Stereo Headset 3Adjusting the in-ear buds for optimum fit 3Pairing the JayBird Bluetooth® Stereo Headset with a Bluetooth® cell phone 4Turning the headset on and off 5Using the headset to listen to music from your cell phone. 5Using the headset to make and answer calls with your cell phone. 5Using your JayBird Bluetooth® Stereo Headset with an iPod® or other MP3 players. 6 Apple iPod® 6 MP3 and other portable audio players 7Specifications 7Warranty 9FAQ / Troubleshooting 9Certification and Agency Approvals 99FCC ID: VL5-JB100
Tx Power Bluetooth Class 2Range 10 meters/33 feetAudio Format 16-bit StereoTalk Time 6.5 Hrs (May vary dependent on usage and cell phone)Music Playing Time 5.5 Hrs (May vary dependent on usage and cell phone)Standby Time 110Hrs (May vary dependent on usage and cell phone)Battery 135 mAh Lithium PolymerCharging AC Charger and USBCharging Time 2 hrsWeight:(Grams) 23.5g (headset) 57.3g (Charger)Microphone type 4mm omni-directionalMicrophone Sensitivity -40 dB +/-3dB (1KHz, 0dB=1V/Pa)speaker sensitivity 114±3dB At 1KHzOperating Temp 14 F to 113 F (-10° C to 45° C) (subject to change)Storage Temp -4 F to 131 F (-20° C to 55° C) (subject to change)AC power supply 5V DC 1A 100-240VAC, 50-60Hz inputNo of Paired Device 2Pairing passkey 0000Features Answer call, end call, reject call, volume controlAgency Approvals FCC, CEIncluded In Box• JayBird Bluetooth Stereo Headset • Charger Dock • AC Power Supply (BSA Style Plug) • USB Charging Cable • Nylon Mesh Carrying Pouch • User ManualCompatibilityA full list of A2DP Cell Phones will be available upon completion of testing (August 2007)What’s included in this package?1. JayBird Bluetooth® Stereo Headset2. Charger Dock3. AC Power Adapter4. USB Charging Cable5. Nylon Mesh Carrying Pouch6. This User Manual18Note: Your AC Power Adapter might appear different than the one shown above (depending on where you purchased this product).1 2 34 5 6
Product Features1. Left Earpiece2. Right Earpiece3. Adjustable In-Ear Buds4. Power/Talk Button5. Volume Down Button6. Volume Up Button7. Rechargeable Lithium Polymer Battery8. Flex-Fit Design9. Rubberized Surfaces for Ultra-Comfort10. Gasket Sealed Construction11. Bluetooth® 2.0 with A2DP Wireless Technology12. Bluetooth(R) Status Indicator13. Battery Charging Status Indicator14. Sweat-proof and Water Resistant Speakers15. Omni-Directional Microphone16. Behind-the-head Back BandCharging your headset Your JayBird Bluetooth® Stereo Headset is powered by a built-in rechargeable battery. Before using your headset for the first time, you should fully charge the battery. 1. Insert the headset into the Charger Dock as shown below making sure that both earpieces are pushed all the way into the charger slots. 2. Plug the smaller connector of the USB Cable into the DC-IN port on the back of the Charger Dock.3. Plug the other end of the USB Cable into any open USB port on your computer or into the USB port on the supplied AC power adapter and then plug the AC power adapter into an outlet.The JayBird Bluetooth® Adapter for iPod® can be purchased at stores selling the JayBird Bluetooth® Stereo Headset or you can purchase online at www.jaybirdgear.comComplete instructions are included.MP3 and other portable audio playersThe optional JayBird Bluetooth® Adapter for MP3 (Model number JB-BA-100m) connects directly any 3.5mm stereo headphone jack, making it compatible with many audio devices including:• MP3 players• Portable CD/DVD players• Portable radios including satellite radios.• Laptop ComputersThe JayBird Bluetooth® Adapter for MP3 is rechargeable and docks directly with the Charge Dock included with your JayBird Bluetooth® Stereo Headset for recharging. The JayBird Bluetooth® Adapter for MP3 can be purchased at stores selling the JayBird Bluetooth® Stereo Headset or you can purchase online at www.jaybirdgear.comComplete instructions are included.Specifications Type In-Ear StyleSealing: Water Resistant/Sweat ProofNoise Cancelling Yes - CVC(R) Clear Voice Capture Echo and Noise SuppressionResponse Bandwidth 20-20000HzImpedance: 32 OhmOutput 10mW RMSAudio S/N Ratio -91 dBTotal Harmonic Distorition (THD) <5% (1KHz, 10mW)Protocol Bluetooth 2.0, A2DP, Handsfree, HeadsetFrequency Band 2.4 GHz721 2104567912151683141311Optional Bluetooth® Adaptershown above sold separately.
4. The LED indicator on the right earpiece will glow RED during the charge cycle (about 2 hours to fully charge). The LED will turn OFF when fully charged.5. Remove headset from Charger Dock.Note: When the battery needs to be recharged, the LED indicator will alternate blue and red color every 5 seconds.Wearing the JayBird Bluetooth® Stereo Headset Getting your JayBird headset on for the first time maybe challenging but stick with it, you will get the hang of it after a couple of times. The JayBird headset is designed and built for performance fit under any circumstance so it’s like putting on tight fitting performance clothing. Instructions for first use:1. Stand in front of a mirror2. Make sure the left side ear bung is rotated to the default 2 o’clock position and the right side ear bung is rotated to the default 10 o’clock position (as shown in figure 7)3. SLIGHTLY pull the earpiece open4. Applying your thumb behind your ear, guide your ear through the hole the headset makes, making sure your hair is out of the way5. Move the speaker into place snug into your ear canal6. While grasping the top of your ear with your fingers, pull the head set down to fit7. Adjust the headset and speaker into the most comfortable position8. Take other earpiece around the back of your head making sure that the behind-the-head wire is under your hair and sits against your neck below your hairline.9. Repeat steps 1 through 5 for the other ear.phone ring through the speakers on your JayBird Bluetooth® Stereo Headset. The sensitive microphone on the JayBird Bluetooth® Stereo Headset will pick up your voice when you talk during your phone call. To terminate the call, either press the Power/Talk button on the JayBird headset, use your cell phone dial pad button, or wait for the other party to terminate the call on their end. You can also terminate the call on your cell phone by pressing the end call button on your cell phone dial pad. Refer to your cell phone user manual on how to make and end calls using a wireless headset.2. When a call comes in to your cell phone, you will hear an ascending ring through the JayBird Bluetooth® Stereo Headset speakers. Your cell phone will also ring and/or vibrate (unless you have the ringer and/or vibrate mode turned off). Answer the call by pressing the Power/Talk button on the right hand earpiece. You can also answer the call using your cell phone dial pad button. To terminate the call, either press the Power/Talk button on the JayBird headset, use your cell phone dial pad button, or wait for the other party to terminate the call on their end. Refer to your cell phone user manual on how to answer incoming calls using a wireless headsetNote: You can make and receive calls even when listening to stereo music. The music will be paused during your phone call and will resume upon call termination..Using your JayBird Bluetooth® Stereo Headset with an iPod® or other MP3 players.You can listen to music from any supported Apple iPod® or other MP3 players using the appropriate JayBird Bluetooth® Adapter. Apple iPod® The optional JayBird Bluetooth® Adapter for iPod® (Model number JB-BA-100i) connects directly to the iPod® 30 pin dock connector is compatible with the following Apple iPod® models:• iPod Nano• iPod with video (5G)• iPod mini• iPod (4G, photo)The JayBird Bluetooth® Adapter for iPod® draws its power directly from the iPod® so no battery or charging is required.36CHARGE STATUS INDICATOROptional Bluetooth® adapter and iPod® shown above are sold separately.
Adjusting the in-ear pieces for optimum fitYou can rotate the adjustable in-ear buds 360 degrees to achieve a different fit of the earpiece to the ear. The default positions as shown in figure 7 are strongly recommended.Pairing the JayBird Bluetooth® Stereo Headset with a Bluetooth® cell phone If your cell phone supports the Bluetooth® A2DP protocol and if it can stream stereo music, you can use your JayBird Bluetooth® Stereo Headset to listen to music in addition to making and receiving phone calls. If your Bluetooth® cell phone does not support A2DP and streaming music, you can still use it make and receive phone calls, but you will need an alternate device such as an iPod® or other MP3 player and an optional JayBird Bluetooth® Adapter to listen to music on the JayBird Bluetooth® Stereo Headset. The first step is to pair your phone with the JayBird Bluetooth® Stereo Headset:1. Make sure that Bluetooth® mode is enabled on your cell phone (refer to your cell phone user manual).2. Press and hold the Power/Talk button on your JayBird Bluetooth® Stereo Headset. After a few moments, you will see quick blue flashes followed by alternating blue and red blinks. The headset is now in pairing mode.3. From your cell phone, perform a discovery/search (refer to your cell phone user manual). 4. The cell phone will list all devices found within range.5. Select JayBird JB-100 Headset6. Select OK or YES to pair your JayBird Bluetooth® Stereo Headset with your cell phone.7. You will be asked for a passkey. Enter 0000 8. Once paired, the LED on the JayBird Bluetooth® Stereo Headset will blink blue every 6 seconds.Note: The pairing method described above is for most common Bluetooth® enabled cell phones. Refer to your cell phone user manual for detailed pairing instructions.9. To verify that your JayBird Bluetooth® Stereo Headset has established a handsfree calling connection, dial a call using your cell phone. If the call completes correctly (if you hear ringing on the JayBird Bluetooth® Stereo Headset), you have succeeded in establishing a handsfree calling connection. 10. To verify that your JayBird Bluetooth® Stereo Headset has established an A2DP (streaming music) connection, play music on your cell phone. If you hear stereo music on your JayBird Bluetooth® Stereo Headset, you have succeeded in establishing an A2DP (streaming music) connection.Turning the headset on and offAfter successful paring of the headset to your cell phone, you can simply turn the headset on when you wish to use it and off when you are through using it.1. To turn on the headset, press the Power/Talk button for a moment. The LED indicator on the right hand earpiece will blink in rapid succession. Release the button. The LED indicator will blink once very 6 seconds indicating that it is on and connected to the cell phone.2. To turn the headset off, press the Power/Talk button for a moment. The LED indicator will blink in rapid succession. Release the button. The headset is now off (and the LED indicator should not be blinking).Using the headset to listen to music from your cell phone.1. Upon successful paring to your A2DP (music streaming) capable cell phone, use the music player feature to listen to stereo music on your JayBird Bluetooth® Stereo Headset. Refer to your cell phone user manual for detailed instructions on how to play music on your cell phone.2. Adjust the volume on both the cell phone and/or music player and on the JayBird Bluetooth® Stereo Headset so that there is no distortion. It’s a good idea to not use maximum volume on the cell phone and/or cell phone music player. Refer to your cell phone user manual for detailed instructions on how to adjust the music volume on your cell phone.Using the headset to make and answer calls with your cell phone. 1. To make calls, simply dial the call on your cell phone. You will hear the 54

Navigation menu