Pmi Piranha Gsx Users Manual

2015-09-01

: Pmi Pmi-Piranha-Gsx-Users-Manual-804595 pmi-piranha-gsx-users-manual-804595 pmi pdf

Open the PDF directly: View PDF PDF.
Page Count: 2

The GSX eForce grip frame is capable of high rates of fire and an agitating hopper such as an
Extreme Rage Overdrive, VL Revolution, Halo, or Evolution 2 is recommended for better performance.
SEAR RELEASE SLIDE:The sear release slide is located on the left
hand side of the eForce grip frame. To reinstall the bolt/block/hammer
assembly, push the sear release slide up before the hammer comes in
contact with the sear. That will allow the bolt/block/hammer assembly
to slide easily into the marker.
INSTRUCTIONS FOR USE
ON/OFF BUTTON: The on/off is the silver button located on
the left hand side of the gripframe. Push it once and the red on/off
indicator will then light up. Push the on/off button again to turn it
off. The frame should be left offwhen not using the marker or you
will drain the battery.
WARNING: Never use water to clean the marker, or you run the risk of damaging the electronic trigger frame.
Cocking Rod
Velocity
Adjustment
Screw
On/Off Button
Sear Release
Charge Port
Gas Thru Grip
Drop Forward
High Performance 2-Piece Barrel
10º Bottom Line
Adapter
GSX BATTERY: The GSX comes with a 9 volt rechargeable battery. You must charge it for a full 22 hours before initial use since the it does not come fully
charged. For best long term battery life, repeat this process every time it is drained. You can also use a regular 9 volt battery with this frame if your rechargeable
battery is dead or if you want to play with the frame right away. You will need to remove the right grip panel when you need to replace it.
On/OffIndicator
WARNING: PMI RECOMMENDS USING THE 9V RECHARGEABLE BATTERY PROVIDED FOR OPTIMAL PERFORMANCE. DO NOT
USE THE BATTERY CHARGER WHEN USING ANY NON-RECHARGEABLE BATTERY.
GSX
BURST BUTTON Press the Burst Button once to turn the marker on 3
Shot Burst. Press the Burst Button again to turnthe frame to 6 Shot Burst.
Press the Burst Button again to turnthe frame to 9 Shot Burst. Press the
Burst Button again to turnit back to semi-auto.
FULL AUTO BUTTON Press the Full Button once to turn the frame to
Full Auto. Press the Full Button again to turn it back to semi-auto.
eFORCE BATTERY The eForce frame comes with a 9 volt
rechargeable battery. You must charge it for a full 22 hours with the
marker turned off before initial use since it does not come fully
charged. For best long termbatterylife, repeat this process every
time it is drained. You can also use a regular 9 volt battery with this
frame if your rechargeable batteryis dead or if you want to play
with the frame right away. You will need to remove the right grip
panel when you need to replace it. A blinking on/offindicator light
means your eForce frame needs to be charged right away. Always
charge with the marker turned off.
TOURNAMENT LOCK SWITCH The Tournament Lock Switch
enables you to play in a tournament or at a field that does not allow full
auto and burst modes by restricting the marker to semi-automatic only. All
eForce frames come with the Tournament Lock off so you can immediately
put the marker in full auto or burst mode. See Piranha manual (5.3) page
32 or Piranha manual (5.1) page 28.
1. Vertical Feed Receiver N/A
2. Barrel N/A
3. Optimized Pressure Chamber N/A
4. Sight Rail N/A
5. Field Strip Pin Assembly 10021
6. Valve Body 71663
7. Valve Cup Seal Assembly 10127
8. Vertical Top Tube N/A
9. Valve Guide 10520
10. Valve Spring 71597
11. Minlon Bolt 71668
12. Rear Block w/Cushion 71662
13. Minlon Cocking Rod 71669
14. Hammer Assembly 10024
15. White Hammer Spring 71598
16. ASA O-Ring 10608
17. Spring Guide 10301
18. Vertical ASA Adapter 71520
19. Flat Ball Detent Cap 71489
20. Ball Detent 10160
25. Velocity Screw 10026
26. Valve Set Screw 10514
27. ASA Screw 71580
28. Ball Detent Screw 10180
31. Sight Rail Screws 71581
32. Bolt Pin 10291
33. Velocity Screw O-Ring 10460
34. Rear Block O-Rings 10260
35. Blue Hammer O-Ring 10129
36. Screen Filter 71667
37. Bolt O-Rings 41010
37. Valve O-Rings 41010
37. Gas Thru Grip O-Ring 41010
37. Optimized Pressure Chamber O-Ring 41010
39. Barrel O-Ring 10161
40. Gas Thru Foregrip N/A
41. 7" SS hose 47015
42. Bottom line SS screw 42016
43. 10˚ Bottom Line Adapter 42013
45. 90° Elbows 47000
59. Front Bolt O-Ring 57738
60. Standard Cocking B/B/H Assembly 71297
61. eForce Polymer Double Trigger Frame Assembly 59093
62. eForce Sear Release Slide 71585
63. Grip 70105
64. Rear Trigger Frame Screw 71583
65. Front eForce Trigger Frame Screw 71582
66. Grip Screws 10782
67. eForce Trigger 71586
68. eForce Sear 71591
69. eForce Trigger Spring 71587
70. eForce Sear/Trigger Pin 71588
71. eForce Trigger/Spring Pin 71589
72. eForce Sear Spring 71590
73. eForce Board Screws 71592
74. eForce Board Cover 71593
75. eForce Electronic Board 71594
76. eForce Solenoid 71595
77. eForce Charge Port Cover 71596
78. 8.4V Rechargeable Battery 70181
25
N/A
39
N/A 37
11
12
13
17
15
42
45
41
26
N/A
33
32
N/A
10 37
96
28
19
20
N/A
31
34
14
35
5
16
18
27
45
37
7
37
37
36
59
60
65
62
66
68
72
71
63
67
61
66
70
69
77
73
75
74
76
64
70
78
N/A
42
31 N/A
EXCLUSIVE!

Navigation menu