Pmi Piranha Pro E Users Manual

: Pmi Pmi-Piranha-Pro-E-Users-Manual-804598 pmi-piranha-pro-e-users-manual-804598 pmi pdf

Open the PDF directly: View PDF .
Page Count: 2

Download
Open PDF In Browser	View PDF

®

INSTRUCTIONS FOR USE

PRO-E

The Pro-E grip frame is capable of high rates of fire and an agitating hopper such as a VL Revolution,
Halo, or Evolution 2 is recommended for better performance.
COCK MARKER BEFORE AIRING UP: Due to low pressure valving, you

must cock the marker first or it may leak down the barrel. Simply pull the cocking
rod in the back of the marker and the flush cocking rod will slide back into the
marker after it is cocked.

Cocking Rod

Velocity
Adjustment

The on/off is the blue button located on
the left hand side of the grip frame. Push it once to turn your Pro-E
on. Push it again and the frame will turn off. The frame should be left
off when not using the marker or you will drain the battery.
ON/OFF BUTTON:

Sear Release
Red Button

Read your instruction manual and follow all the rules of marker
safety. Hold the green button down to turn the marker to Semi, Burst or Full
Auto. Lightly pressing the Green Button will cycle through the menus.

SAFETY:

All menus can be accessed in Safe Mode
Burst – 1-5 shot burst (red button)
Count A – 0 to 160 (red button)
ROF – 1-15 (red button) (controls burst and full modes)
ROF MAX – 1-15 (controls semi mode only)
Timer – 60:00 (red button to change) (blue button starts countdown)

Blue Button
On/Off

LCD
(see below)
Charge Port

MODES OF FIRE:

Green Button
Change Modes/
Scroll Menu

Regulator
Adjustment

The sear release slide is located on the left hand
side of the Pro-E grip frame. To reinstall the bolt/block/hammer assembly, push
the sear release slide up before the hammer comes in contact with the sear.
That will allow the bolt/block/hammer assembly to slide easily into the marker.

SEAR RELEASE SLIDE:
LCD DISPLAY
Alarm

Tournament Lock
Battery Indicator

COUNT A B

00:00
Counter/Timer

Fire Modes

SAFE SEMI bur FULL

BURST
TIMER
ROF MAX
Safe Mode
Only Menus

The regulator pressure can be changed with a 1/8” allen
wrench. Screwing the adjustment screw in will lower the pressure. The regulator
should be set near 300 psi to get 300 fps. Lower regulator pressure will lower
velocity, but if the pressure gets too low, the marker might not recock.
REG PRESSURE:

WARNING: Never use water to clean the marker, or
you run the risk of damaging the electronic trigger frame.

The Pro-E comes with a 9 volt rechargeable battery. You must charge it for a full 22 hours before initial use since the it does not come
fully charged. For best long term battery life, repeat this process every time it is drained. You can also use a regular 9 volt battery with this frame if your
rechargeable battery is dead or if you want to play with the frame right away. You will need to remove the right grip panel when you need to replace it.
PRO-E BATTERY:

WARNING: PMI RECOMMENDS USING THE 9V RECHARGEABLE BATTERY PROVIDED FOR OPTIMAL PERFORMANCE. DO NOT
USE THE BATTERY CHARGER WHEN USING ANY NON-RECHARGEABLE BATTERY.
The tournament lock switch enables you to play in a tournament or at a field that does not allow full auto and burst
modes by restricting the marker to semi-automatic only. Pro-E frames come with the tournament lock off so you can immediately put the marker in full auto
or burst mode. The lock is a silver button you can access by removing the right grip panel and lifting out the battery. Simply press it once to turn the lock on.
TOURNAMENT LOCK SWITCH:

8

2

39

3

37

37
1

3B
6
3C
3D

11

10

50

20

37

51

34
52
12

53

9

7

37
28

19

26

18

16

35

32

13

57

67

56

27

33

37
5

30

29

14
15

68
38

25

17

29

69
21

70
30

71

23

54
72

73
74
42

72
72
43
75

42

41

69
82

76

45

81
77
83

78
80
79

1. Vertical Feed Receiver
2. Barrel
3. Ram Air Chamber
3B. Ram Air Spring
3C. Ram Air Piston
3D. Piston O-Ring
4. Sight Rail
5. Field Strip Pin
6. EXT Valve Body
7. Valve Cup Seal Assembly
8. Vertical Top Tube
9. Valve Guide
10. Valve Spring
11. Venturi Bolt
12. Flush Cocking Rear Block w/ Cushion
13. Flush Cocking Rod
14. Hammer
15. Hammer Spring
16. ASA O-Rings
17. Spring Guide
18. Vertical ASA
19. Ball Detent Cap
20. Ball Detent
21. Double Trigger Frame Assembly
22. Sear Release Slide
23. Pro-E Grips
25. Thumb Adjust Velocity Screw
25A. Velocity Lock Screw
26. Valve Set Screw
27. ASA Screw
28. Ball Detent Screw
29. Trigger Frame Screws
30. Grip Screws
32. Bolt Pin
33. Velocity Screw O-Ring
34. Rear Block O-Rings
35. Hammer O-Ring

71505
71563
71545
71599
71579
10608
71570
10021
71663
10127
71515
10520
71597
10209
71661
10201
10310
71598
10608
10301
71525
10101
10160
70155
70128
70100
10482
42029
10514
71580
10180
70537
10782
10291
10460
10260
10129

37.
37.
37.
37.
37.
38.
39.
41.
42.
43.
44.
45.
50.
51.
52.
53.
54.
55.
56.
57.
67.
68.
69.
70.
71.
72.
73.
74.
75.
76.
77.
78.
79.
80.
81.
82.
83.

Bolt O-Ring
Valve O-Ring Front
ASA O-Ring Front
Ram Air body O-Ring
Regulator O-Ring
Pro-E Trigger
Barrel O-Ring
4.4” Hose
Bottom Line SS Screws
10˚ Bottom Line Adapter
Sear
90° Elbow
Flush Cocking Guide O-Ring
C-Clip
Retaining Washer
Flush Spring
Drop Forward
Trigger Spring
Trigger/Sear Pin
Sear Spring Pin
Low Pressure Gauge
Reg NGO Top
Reg Seat Seal
Reg Poppet O-Ring (013-70)
Reg Poppet
Reg Seat Base O-Ring (006-70U)
Reg Spring
Reg Seat Base
Reg Body Mid (black)
Reg Bottom Swivel (black)
Reg Bottom Bolt O-Ring (012-70 Buna)
Reg Bottom Bolt
Reg Adjusting Screw
Reg Adjusting Screw O-Ring
Reg DSR 10-32 Plug
Reg Seal Stop O-Ring (002-70)
Interior Bottom Bolt O-Ring (010-70)

Disassembly of electronic trigger frame will void warranty.

41010
41010
41010
41010
41010
70144
10161
47011
10799
71645
70139
47000
10212
10207
10206
10203
71654
10752
10790
10767
46090
41600
41517
57976
41509
10162
41510
41505
41601
41602
71660
41503
41504
57607
41506
57631
57645

25A



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : Yes
Create Date                     : 2004:10:19 11:16:08
Producer                        : Acrobat Distiller 4.0 for Macintosh
Creator                         : QuarkXPressª: LaserWriter 8 8.7.1
Author                          : 
Title                           : Pro E
Modify Date                     : 2004:10:19 11:16:44-05:00
Page Count                      : 2

EXIF Metadata provided by EXIF.tools