Contents
- 1. User Manual
- 2. Users Manual
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2744284 |
| Application ID | cK/+Abaelf66taPYIJOZbw== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 14.35kB (179338 bits) |
| Date Submitted | 2015-09-11 00:00:00 |
| Date Available | 2015-09-11 00:00:00 |
| Creation Date | 2014-03-27 11:57:06 |
| Producing Software | Acrobat Distiller 11.0 (Windows) |
| Document Lastmod | 2015-09-03 12:47:52 |
| Document Title | Polycom P008 Embedded ISM43341 SIP Application Module for the Polycom RealPresence Trio Solution – User Guide |
| Document Creator | FrameMaker 12.0.4 |
| Document Author: | Polycom, Inc. |
USER GUIDE September 2015 | 3725-20781-001D Polycom® P008 Embedded ISM43341 SIP Application Module for the Polycom RealPresence Trio™ Solution Contents Features Specifications Output Power Levels Circuit Description PCB Integration FCC IC Compliance Statement Safety Information Features The Polycom P008 ISM43341 single-chip quad-radio device provides the highest level of integration for a mobile or handheld wireless system, with integrated dual band (2.4 GHz/ 5 GHz) IEEE 802.11 a/b/g and single-stream IEEE 802.11n MAC/baseband/radio, and Bluetooth 4.0. It integrates a low power NFC controller. The ISM43341 includes integrated power amplifiers, LNAs and T/R switches for the 2.4 GHz and 5 GHz WLAN bands, which greatly reduces the external part count, PCB footprint, and cost of the solution. The Polycom P008 ISM43341 is a fully approved module that complies with the following standards and certifications: ● ETSI EN 300 328 v1.9.1 ● ETSI EN 301 893 v1.7.1 ● ETSI EN 300 330 ● FCC Part 15 Unintentional emissions ● FCC Part 15.247 ● RSS103 I.C ● CISPR 22 ● ETSI EN 301 489-3 ● ETSI EN 301 489-17 ● EN 62311 Polycom P008 Embedded ISM43341 SIP Application Module – User Guide The ISM43341 application module transfers data signals by use of the radio frequency spectrum according to the WiFi, Bluetooth, and NFC standards. It is connected to the Polycom RealPresence Trio solution by a 40-pin flexible cable and is mounted with two machine screws. Specifications For specifications not listed in the following table, refer to the data sheet for the ISM43341 chip device. Radio Frequency Range WiFi 2400MHz to 2483.5MHZ 5150MHz to 5250MHz 5250MHz to 5350MHz 5470MHz to 5725MHz 5725MHz to 5825MHz Bluetooth 2400MHz to 2483.5MHz NFC 13.56MHz 1.8MHz bandwidth Modulation Dynamic Frequency Selection (DFS) OFDM BT FHSS NFC 10% ASK, 100% ASK Power Power over Ethernet (PoE) – also uses PoE+ with external DC-powered Power Injector Temperature Range 0 to 40°C Size 3.3” x 1.1” x 0.25” high Polycom, Inc. Polycom P008 Embedded ISM43341 SIP Application Module – User Guide Output Power Levels Polycom, Inc. Polycom P008 Embedded ISM43341 SIP Application Module – User Guide Circuit Description The Polycom P008 ISM43341 single-chip device provides a small form-factor solution with minimal external components to drive down cost for mass volumes, and allows for handheld device flexibility in size, form, and function. Comprehensive power management circuitry and software ensure the system can meet the needs of high mobile devices that require minimal power consumption and reliable operations. PCB Integration SDIO/I2S/UART Interface/Connection to Motherboard The RealPresence Trio radio module PCB employs a 40-pin flex circuit socket to connect to a motherboard 40-pin flex circuit cable. This interface is for the 3.3 VDC and 1.8Vpower sources and all necessary data lines to communicate with the radio module. Mounting The radio module has two mounting holes. The module should be placed down and fastened onto a motherboard containing two standoffs with metal screws. At the same time, the 40-pin flex cable connector will be engaged by locking the flex connector. Antenna The 2.4GHz/5GHz radio module PCB antennas are mounted permanently for WiFi/BT operation. No external WiFi/BT antennas are allowed. The NFC antenna loop is connected via a two-pin locking connector. Only the Polycom NFC antenna loop or equivalent is allowed. Polycom, Inc. Polycom P008 Embedded ISM43341 SIP Application Module – User Guide FCC IC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: ● This device may not cause harmful interference. ● This device must accept any interference received, including interference that may cause undesired operation. ● Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment User Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, can cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. This module is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring that the end user has no manual instructions to remove or install the module. The module is limited to installation in mobile or fixed applications according to Part 2.1091(b). Separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations. The user’s manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. LE-LAN devices are restricted to indoor operation only in the band 5150MHz to 5250MHz. FCC / IC Canada Labeling of host device The modular transmitter is labeled with its own FCC and IC identification number. If the FCC or IC identification numbers are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label shall use wording as the following: Contains FCC ID: M72-P008 and Contains IC: 1849C-P008. Polycom, Inc. Polycom P008 Embedded ISM43341 SIP Application Module – User Guide FCC RF Exposure requirements The antenna used with this module must be installed to provide a separation distance of at least 20cm from all persons, and must not transmit simultaneously with any other antenna or transmitter. OEM integrators and end users must be provided with transmitter operating conditions for satisfying RF exposure compliance. Antennas The 2.4GHz/5GHz radio module PCB antennas are mounted permanently for WiFi/BT operation. Only the following, or equivalent, are permitted: Unictron Technologies Corp. Chip antenna with 1.4dBi gain at 2.4GHz and 2.3 dBi gain at 5GHz. No external WiFi/BT antennas are allowed. The NFC antenna loop is connected via a two-pin locking connector. Only the Polycom NFC magnetic wire loop antenna with 0db gain or equivalent is allowed Antenna information The module has been tested and approved for use with only the permanently mounted chip antennas on the radio PCB. This radio module is not approved for use with external WiFi/BT antennas. The radio module is approved for NFC use with the plug-in Polycom NFC antenna 2457-69045-003 or equivalent, typically 1.85uHy for a peak field of 1.85A/m or less at 5mm. Antenna types ● The onboard WiFi/BT antennas are a dual-band ceramic chip type AA077 from Unictron Technologies. ● The plug-in NFC antenna is a thin multi-turn loop flex circuit. Antenna gain ● The WiFi/BT antenna gain varies from 1.4dBi, typical for the 2.4GHz band, and 2.3dBi, typical for the 5GHz band (WiFi only). ● The NFC antenna is a magnetic loop that does not radiate and thus has no gain. Note: Obtain authorization for use with unlisted antennas The use of this module in combination with an antenna that is not listed must be authorized with respective regulatory agencies. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication. Safety Information Canada - Industry Canada (IC) Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. Polycom, Inc. Polycom P008 Embedded ISM43341 SIP Application Module – User Guide L‘utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’ utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Caution: Exposure to radio frequency radiation To comply with RSS 102 RF exposure compliance requirements for mobile configurations, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter. Informations sur l'exposition RF Les antennes internes utilisées pour ce transmetteur mobile doivent offrir une distance de séparation d'au moins 20 cm de toute personne. Les conditions de fonctionnement d'émetteur offertes aux intégrateurs OEM et aux utilisateurs finaux doivent satisfaire les normes d'exposition RF. Polycom, Inc. Polycom P008 Embedded ISM43341 SIP Application Module – User Guide Copyright© 2015, Polycom, Inc. All rights reserved. No part of this document may be reproduced, translated into another language or format, or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Polycom, Inc. 6001 America Center Drive San Jose, CA 95002 USA Trademarks Polycom®, the Polycom logo and the names and marks associated with Polycom products are trademarks and/or service marks of Polycom, Inc. and are registered and/or common law marks in the United States and various other countries. All other trademarks are property of their respective owners. No portion hereof may be reproduced or transmitted in any form or by any means, for any purpose other than the recipient's personal use, without the express written permission of Polycom. Disclaimer While Polycom uses reasonable efforts to include accurate and up-to-date information in this document, Polycom makes no warranties or representations as to its accuracy. Polycom assumes no liability or responsibility for any typographical or other errors or omissions in the content of this document. Limitation of Liability Polycom and/or its respective suppliers make no representations about the suitability of the information contained in this document for any purpose. Information is provided "as is" without warranty of any kind and is subject to change without notice. The entire risk arising out of its use remains with the recipient. In no event shall Polycom and/or its respective suppliers be liable for any direct, consequential, incidental, special, punitive or other damages whatsoever (including without limitation, damages for loss of business profits, business interruption, or loss of business information), even if Polycom has been advised of the possibility of such damages. End User License Agreement By installing, copying, or otherwise using this product, you acknowledge that you have read, understand and agree to be bound by the terms and conditions of the End User License Agreement for this product. The EULA for this product is available on the Polycom Support page for the product. Patent Information The accompanying product may be protected by one or more U.S. and foreign patents and/or pending patent applications held by Polycom, Inc. Open Source Software Used in this Product This product may contain open source software. You may receive the open source software from Polycom up to three (3) years after the distribution date of the applicable product or software at a charge not greater than the cost to Polycom of shipping or distributing the software to you. To receive software information, as well as the open source software code used in this product, contact Polycom by email at OpenSourceVideo@polycom.com. Polycom Support Visit the Polycom Support Center for End User License Agreements, software downloads, product documents, product licenses, troubleshooting tips, service requests, and more. Polycom, Inc.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : Polycom, Inc. Create Date : 2014:03:27 11:57:06Z Keywords : Inventek, ISM43341, FCC, RealPresence Trio, Polycom P008 Modify Date : 2015:09:03 12:47:52-05:00 Subject : This document describes features and specifications for using the Polycom P008 ISM43341 module with the Polycom RealPresence Trio Solution. Has XFA : No Language : en XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Creator Tool : FrameMaker 12.0.4 Metadata Date : 2015:09:03 12:47:52-05:00 Format : application/pdf Description : This document describes features and specifications for using the Polycom P008 ISM43341 module with the Polycom RealPresence Trio Solution. Title : Polycom P008 Embedded ISM43341 SIP Application Module for the Polycom RealPresence Trio Solution – User Guide Creator : Polycom, Inc. Producer : Acrobat Distiller 11.0 (Windows) Copyright : © 2015 Polycom, Inc. All rights reserved. Document ID : uuid:319d32f2-021e-4d62-858b-4fca381f07c2 Instance ID : uuid:35c072c1-3870-43ef-bf5a-471402a9e380 Page Mode : UseNone Page Count : 8 Signing Date : 2015:09:03 12:47:52-05:00 Signing Authority : ARE Acrobat Product v8.0 P23 0002337 Annotation Usage Rights : Create, Delete, Modify, Copy, Import, ExportEXIF Metadata provided by EXIF.tools