Porta Phone TD900HDR Full Duplex, High Definition, 900 MHz Transceiver-Remote User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3869546
Application ID	WCkFGfytbWl2fZuD3Ke9oA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	17.36kB (217018 bits)
Date Submitted	2018-05-30 00:00:00
Date Available	2018-05-30 00:00:00
Creation Date	2018-04-28 19:20:04
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2018-05-30 15:40:48
Document Title	C:\Users\Administrator\Desktop\TD900HD User Menu.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Sam

USER MENU
1. Power ON/OFF
Power ON: Press and hold the power button till to BLUE LED light up.
Power OFF: Press and hold the power button till to the RED LED flashing.
2. Pairing/Register mode
a). Press and hold the power button to turn headset power ON, the power LED should
blinking in BLUE color.
b). Press the volume down button
volume up
at 3 times continually, then press and hold the
till to the (REMOTE) RED and Blue LED blinking at alternately or (MASTER)
RED LED blinking.
c). Press the power ON/OFF switch of Master headset to select register to Line(Group) 1,
Line 2 or Line 3.
LINE condition indicate: Line 1: RED LED blinking; Line 2: BLUE LED blinking; Line 3:
ORANGE LED blinking.
d). The LED of Remote headset will turn RED after paired, press the power button to quit
the pairing mode.
e). Repeat the above step “a” to “d” for more Remote headset register on same Master,
press the power
button to finish the register.
(Note: ①. The Master headset can accept maximum 8 remote register in line 1 (Group) and
Line 2 communication in duplex, total register number over 250 headset available on Line
3 but listening only after the 8th headset registered on Line 1 and 2.
②. The the power ON/OFF switch of Master headset for select the Line(GROUP) of the
headset connection. Press power ON/OFF button to select the headset register under the
Line(Group) 1, 2 or Line3 (Line 3 for listening only).
3. Talking and listening
a). The master and remote headset will start to search each other after power ON, the BLUE
LED flash 1 time each 3 seconds. The headset will be link together automatically when the
pairing ID confirmed by master and LED turn ON in blue color.
b). Press the volume up
and down
button to adjust speaker sound volume.
c). The side switch of Master headset for CONFERENCE ON/OFF. Press the switch to
separate the Line (Group) 1, 2 or make all conference.
d). The side switch of Remote headset for select the connection to Line(Group) 1 or
Line(Group) 2.
4. Mic Muted
Swivel up the Mic boom to MUTE the microphone and swivel down to back the normal
talking.
FCC Warning:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
Any Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
Exposure to Radio Frequency (RF) Signals
This is a radio transmitter and receiver. It is designed and manufactured not to exceed the
emission limitsfor exposure to radio frequency (RF) energy set by the Federal
Communications Commission (FCC) of the U.S.Government. These limits are part of
comprehensive guidelines and establish permitted levels of RF energy for the general
population. The guidelines are based on the safety standards previously set by both U.S. and
international standards bodies. These standards include a substantial safety margin designed
to assure the safety of all persons,regardless of age and health. This device and its antenna
must not be co-located or operating in conjunction with any other antenna or transmitter. This
product has been shown to be capable of compliance for localized specific absorption rate
(SAR) for uncontrolled environment/general population exposure limits specified in ANSI/IEEE
Std. C95.1-1992 and had been tested in accordance with the measurement procedures
ISEDC Warning:
This device complies with ISEDC licence-exempt RSS standard(s). Operation is subject to the
following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence.L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
The device has been tested and compliance with SAR limits, users can obtain Canadian
information on RF exposure and compliance
Le présent appareil est conforme Après examen de ce matériel aux conformité aux limites
DAS et/ou aux limites d’intensité de champ RF, les utilisateurs peuvent sur l’exposition aux
radiofréquences et la conformité and compliance d’acquérir
ISEDC Radiation Exposure Statement:
SAR l’utilisation des règles sma l’emplacement Le matériel de transmission et
fonctionnant dans tous les essais à la certification, même si la puissance suprême a
décidé le niveau, utilisation spécifique peut être très en deçà de la valeur de référence
maximale.Types de matériel sont vendus au public un ancien, d’essai et de certification
de l’exposition, limite maximum sma, chaque document et l’emplacement du matériel
d’essai et conformément au document.Le modèle en physique, matériel d’essai et
conforme aux directives d’exposition des radiofréquences sma quand une annexe
désigné pour ce produit lors de leur utilisation ou des pièces de rechange ne contiennent
pas de métal.
ISEDC Specific Absorption Rate (SAR) information
SAR tests are conducted using standard operating positions accepted by the ISEDC
with device transmitting at its highest certified power level in all tested frequency bands,
although the SAR is determined at the highest certified power level, the actual SAR level of the
device while operating can be well below the maximum value. Before a new model device is a
available for sale to the public, it must be tested and certified to the ISEDC that it does not
exceed the exposure limit established by the ISEDC, tests for each device are performed in
positions and locations as required by the ISEDC. this model device has been tested and meet
the ISEDC RF exposure guidelines
To prevent possible hearing damage, do not listen at high volume levels for long periods

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : Sam
Create Date                     : 2018:04:28 19:20:04+08:00
Modify Date                     : 2018:05:30 15:40:48-07:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2018:05:30 15:40:48-07:00
Producer                        : Acrobat Distiller 11.0 (Windows)
Format                          : application/pdf
Title                           : C:\Users\Administrator\Desktop\TD900HD User Menu.doc
Creator                         : Sam
Document ID                     : uuid:7709894f-6349-446b-a613-d0cda1894d75
Instance ID                     : uuid:8114c54f-3927-45c5-89cb-ae02197c9ccf
Page Count                      : 3

EXIF Metadata provided by EXIF.tools