Porta Phone ULR2015 DUPLEX WIRELESS SYSTEMS User Manual Ultralite M MDuserManual
Porta Phone Company Inc DUPLEX WIRELESS SYSTEMS Ultralite M MDuserManual
Users Manual
Page 1
DUPLEX WIRELESS SYSTEMS
user manual
Introduction
Thank you for your choice of DUPLEX WIRELESS SYSTEMS.
This is a DECT (Digital Enhanced Cordless Telecommunications) duplex wireless system. To the quality of
audio and to the safety offered from the digital technology, The offers manifold and useful features including
Full duplex system, LED In use illumination, multi-headset capabilities and multi-volume select. Please read this
instruction carefully before using your new system for the first time.
A glance guide for the headset
A glance guide for the base unit
Installation
Please check your package the following items(options):
-Base Unit
-Wireless Headset
-Wire Headset (Ultra 3G-S/ Ultra 3G-D)
- Packing batterie(800mAH/3.7V)
Mic
Vol down
Power on/off
3.7v battery pack
Vol up
Receiver
SUB key
Vol up
Vol down
Mic
battery pack
battery pack
Vol up
Vol down
Power on/off
EarJack
Receiver
ComStar Ultralite-R(ULR2015)
ComStar Ultralite-RD(ULRD2015)
ComStar Clip(CLIP 2015)
Ultralite M(ULM2015) Ultralite MD(ULMD2015)
(Ultralite M(ULM2015)/Ultralite MD(ULMD2015))
(ComStar Ultralite-R(ULR2015)/ComStar Ultralite-RD(ULRD2015)/ComStar Clip(CLIP2015))
Page 2
The pack rechargeable batteries come with your charger.
-Insert the rechargeable battery into the headset and base as the above figure indicated, matching correct polarity.
-Fit the battery compartment cover by sliding it down so that it clicks firmly into place.
NOTE: Reversing the orientation may damage the headset and base. Please use the battery type supplied or recommended
equivalents. A different battery could cause an explosion or damage of your headset.
Low battery indicator
Whenever you see the low battery indicator LED flash on the headset, or you have heard the low battery warning
tone during a call conversation, please:
-End the call as soon as possible.
-Change the headset battery.
To charge the battery, put the battery into the charger cradle. The charging LED on charger unit will come on to
indicated that the battery is in charging.
Basic Functions
Make a talk
-Power up the headset to search registered of base, the “In use” LED is ON.
During a talk conversation, you can adjust the talk volume (1 ~ 5 levels) by simply pressing • or ‚ key.
Mute
-During a call conversation, you can mute your voice by rise up microphone arm.
-Deactivate the mute function, go down the microphone arm again.
Headset Power On / Off
To power Off the headset
- Press and hold “power on/off” key about 3 seconds, the headset will switch off which can prolong the use
time of headset.
To power On the headset
-Press “power on/off” key
The headset will power on with the “In use” LED light, the headset to search registered of base.
Out of range indication
Wire Headset
Ultra 3G-D
Ultra 3G-S
Wireless Headset
Ultralite M(ULM2015)/Ultralite MD(ULMD2015)
ComStar Ultralite-R(ULR2015)
ComStar Ultralite-RD(ULRD2015)
ComStar CLIP(CLIP2015)
Page 3
If your headset has registered and is in located range, the “In use” LED will blanking steadily, when your
headset goes out of range, the communication link will be lose temporarily, the “In use” LED will blink.
If you go back to the located range again, the communication link will restore, also the “In use” LED will
blanking steadily.
Note: your talk will be cut without any audible warning tone if you are in a talk and out of the located range.
Registration
The headset and base shall be factory pre-registered with the identification digital security codes, which are
stored into the non-volatile memory, so that your headset shall be ready for working after out-of-box. However,
your headset shall also has a procedure to allow you to re-do the registration operation in case of the link is lost
accidentally.
-press ‚ key 3 times, Press and hold • key for 3 seconds on the headset “In use” LED is ON, your headset
entered the registration mode
-Press and hold SUB key for 3 seconds on the base until “SUB” LED is flashlight, the base also entered the
registration mode.
-About 5-10 seconds the headset “In use” LED is OFF and following to ON, that means the headset has located
the base, and the base until “SUB” LED is OFF and following to ON.
-If the headset does not locate the base, the headset “In use” LED will be blink after 15 seconds and it will
return to the non-located mode. Try again and check that you are not in the interference environment
Note: your base can register up to three headsets.
Unsubscribe headset registered
-At standby mode
-Press and hold SUB key enter the base’s registration mode with the “SUB” LED is flashlight
-Press SUB key 7 times again the “SUB” LED is quick flash
-All headsets registered to this part are cleared
LIMITED WARRANTY
This limited warranty only applies to the use of this device with a communications service for which it
is designed. This device alone does not provide the customer with any communications service and
requires a separate subscription to a communications service from a service provider. Altering
service provider-specific settings may void the warranty. This limited warranty does not warrant that
the device will be free of any limitations of voice quality or service caused by (1) the services provided
by the customer’s underlying communications service provider; or (2) interference from other radio
frequencies or transmissions, static electricity, and other electronic devices.
Exposure to Radio Frequency (RF) Signals
This wireless headset is a radio transmitter and receiver. It is designed and manufactured not to exceed the
emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission
(FCC) of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted
levels of RF energy for the general population. The guidelines are based on the safety standards previously set
by both U.S. and international standards bodies. These standards include a substantial safety margin designed to
assure the safety of all persons, regardless of age and health. This device and its antenna must not be co-located
or operating in conjunction with any other antenna or transmitter.
This product has been shown to be capable of compliance for localized specific absorption rate (SAR) for
uncontrolled environment/general population exposure limits specified in ANSI/IEEE Std. C95.1-1992 and had
Page 4
been tested in accordance with the measurement procedures specified in FCC/OET Bulletin 65 Supplement C
(2001) and IEEE 1528.
FCC information
Any Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
l Reorient or relocate the receiving antenna.
l Increase the separation between the equipment and receiver.
l Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
l Consult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by PortaPhone could void the user's authority to operate the equipment.
Privacy of communications may not be ensured when using this equipment.
Privacy of communications may not be ensured when using this phone.”
IC Information
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
The device been tested is compliance with RF field strength limits, users can obtain Canadian information on
RF exposure and compliance.
Le présent appareil est conforme .Après examen de ce matériel aux conformité ou aux limites d’intensité de
champ RF,les utilisateurs peuvent sur l’exposition aux radiofréquences et la conformité and compliance
d’acquérir.les informations correspondantes.