Position Technology POSIPIN User Manual CR R885 A manual

Position Technology Inc CR R885 A manual

Contents

CR R885 A manual

PIN and Proximity ReaderFor Access Control Systems(CR-R885-A)Installation and Operating InstructionsVersion 1.0
PosiPin 1TABLE OF CONTENTSInstallation ............................................................................2Technical Specifications .......................................................3Feedback ..............................................................................5Programming ........................................................................5Card/Code Options ...............................................................6Keypad Communication Format ...........................................6Transfer Limit for 4-bits Buffered Format .............................7Display on Card Read ..........................................................7Keypad Lockout ....................................................................826-bit Wiegand Card Family Code Setting ...........................8Reader’s Interface ................................................................9Check-in Supervision ...........................................................9Buzzer Setting ....................................................................10Face Light Intensity ............................................................10Face Light Operation ..........................................................10Face Light Colour ...............................................................10Changing the Installer Code ...............................................11Panic Alarm ........................................................................11Resetting to Default ............................................................11Card Presentation Test ......................................................12Warranty .............................................................................12
2 Installation and Operating InstructionsINSTALLATIONFor PosiPin to function correctly with the access control system,some programming may be required in the controller or controlpanel of the host system. For further instructions, refer to theappropriate manual. Only explanations directly concerningPosiPin’s programming will be included in this manual. Selecting an Installation Site:• Avoid wiring the PosiPin cables in the same conduit as AC powercables, lock power or signal wiring.• Reader wiring must remain a minimum of 30cm (12in) away fromother wiring, such as wiring for AC power, computer data,telephones, electric locks, etc.• Avoid sites within 1.1m (3.5ft) of computer monitors or CRTs.• Avoid sites near sources of broad spectrum EMI noise, such asmotors, pumps, generators, DC to AC converters, AC switchingrelays, power supplies, and light dimmers.• Avoid sites near potential sources of RF signals, such as cellularphones, two-way radios, etc.Mounting and WiringAfter selecting a site for the PosiPin, use the mounting plate as aguide to drill two holes to secure the mounting plate and a hole forthe cable 0.95cm to 2.54cm (0.375in to 1in) wide. Place a grommetaround the edge of the hole for the cable. Prepare PosiPin’s cableby cutting the cable jacket back 3.175cm (1.25in) and stripping thewires back 0.635cm (0.25in). Splice PosiPin’s wires with arecommended cable wire. Route the cable to the controller andconnect as shown in Figure 1: Connection drawing on page 4.
PosiPin 3Mounting on Metal SurfacesAlthough the read range may slightly decrease, PosiPin can bemounted on metal. However, do not box in or surround the cardreader with any kind of metal. If the reader must be installed in ametal enclosure, ensure that the face of the card reader is notcovered and that at least 1.6" (4cm) remain between the cardreader and the metal on all sides of the card reader.TECHNICAL SPECIFICATIONSInput Voltage: Typical: 13.8Vdc, min.: 11.0Vdc, max: 14.5VdcInput Current: Typical: 65mA @ 12.5Vdc, with card: 105mAConsumption: Typical: 812mW @ 12.5Vdc, with card 1.31mWFrequency: Exciter Field: 125KHz Pulse Modulated, receive low:12.500KHz, Receive high: 15.625KHzOperating Temp: -35°C (-31°F) to +65°C (+149°F)Output formats: Reader: 26- and 37-bit WiegandKeypad: 8-, 26- and 37-bit Wiegand, 4-bit with orwithout parity, and 4 bits buffered with or without parityCable Distance: 152.4m (500ft.)Suggested Cables: 22AWG, 0.8mm, Multi-conductor, Alpha 5196, 519818AWG, 1.2mm, Multi-conductor, Alpha 5386, 5388Belden 9553, 18AWG, 6-conductor, stranded w/overall shieldIndicators: Beeper, red LED, green LED, red or green Face LightWeight: 280g (9.8 oz.)Material: Black, UV resistant, ABS plasticDimensions: 99.5mm (5.75in.) x 118.5mm (2in.) x 19.5mm (1in.)
4 Installation and Operating InstructionsFigure 1: Connection drawing
PosiPin 5FEEDBACKVisual Feedback: When information is entered on the reader’skeypad, the red and/or green LEDs will flash, remain constant orextinguish depending on the operation.Confirmation Beep: When an operation is successfully entered,the reader emits a rapid series of beep tones (“beep-beep-beep-beep-beep”).Rejection Beep: When the system reverts to a previous status oran operation is incorrectly entered, the reader emits one long beeptone (“beeeeeeeeeep”).PROGRAMMINGEnsure that corresponding programming is completed in thecontrol panel or controller connected to the PosiPin. To program:1. Press and hold the [CLEAR] key for 4 seconds.The reader emits a confirmation beep and the green LED illuminates.2. Enter the [INSTALLER CODE]. Press the [ENTER] key. (default:000000) Reader emits a confirmation beep and the green LEDflashes.3. Enter the 3-digit [SECTION]. Press the [ENTER] key.Reader emits a confirmation beep and the green LED stops flashing.4. Enter the required [DATA]. Press the [ENTER] key.The reader emits a confirmation beep and the green LED flashes.5. To program another section, repeat steps 3 and 4. To exitprogramming mode, press and hold the [CLEAR] key for 4 sec.The reader emits a rejection beep and the green LED extinguishes.
6 Installation and Operating InstructionsCARD/CODE OPTIONSSection [001][001][001][001] - Default: [3][3][3][3]PosiPin can function as a reader, a keypad or as both combined.KEYPAD COMMUNICATION FORMATSection [002][002][002][002] - Default: [1][1][1][1]PosiPin must use the same keypad communication format as thecontroller. Enter Description[0] Keypad and reader disabled. For programming only. [1] Reader only enabled. A user must present a valid card to the reader for Access Granted.[2] Keypad only enabled. A user must enter a valid code on the keypad for Access Granted.[3] Keypad and reader enabled. A user must present a valid card and enter a valid code for Access Granted.Enter Description[0] 8-bit Wiegand [1] 26-bit Wiegand (also see section [006])[2] 37-bit Wiegand[3] 4 bits without parity[4] 4 bits with parity[5] 4 bits buffered without parity(also see section [003])[6] 4 bits buffered with parity (also see section [003])
PosiPin 7TRANSFER LIMIT FOR 4-BITS BUFFERED FORMATSection [003][003][003][003] - Default: [00][00][00][00]This feature sets the number of digits retained in memory beforethe data is sent to the controller. For example, if section [003] is setat 05, PosiPin will transmit once 5 digits are entered on the keypad. This feature only applies when the format programmed inSection [002] is set for Option [5]: 4 bits buffered withoutparity or Option [6]: 4 bits buffered with parity.DISPLAY ON CARD READSection [004][004][004][004] - Default: [3][3][3][3]PosiPin’s response to a card being presented to the reader can beadjusted according to the installation’s requirements. Enter Description[01] to [11] If section [002] is Option [5]: 4 bits buffered without parity[01] to [10] If section [002] is Option [6]: 4 bits buffered with parity.Enter Description[0] Display on Card Read disabled[1] Red Status LED flashes[2] Green Status LED flashes[3] Red and green Status LEDs flash[4] Face Light flashes[5] Face Light and red Status LED flash[6] Face Light and green Status LED flash[7] Face Light and both Status LEDs flash
8 Installation and Operating InstructionsKEYPAD LOCKOUTSection [005][005][005][005] - Default: [0][0][0][0]The PosiPin keypad comes with a feature that will lock the keypadfor 60 seconds when an installer code is entered incorrectly 3consecutive times. 26-BIT WIEGAND CARD FAMILY CODE SETTINGSection [006][006][006][006] - Default: [000][000][000][000]When the keypad is enabled, the card’s family code must beprogrammed in order for the keypad to recognize the user’s PIN.When a user enters a PIN on the keypad, PosiPin will automaticallyadd the family code programmed in section [006] to the beginningof the PIN before transmitting the data to the controller. Therefore,also ensure that all cards to be used with the PosiPin contain thesame family code.This feature only applies when the communication formatprogrammed in Section [002] is set for Option [1]: 26-bitWiegand.Enter Description[0] Keypad Lockout disabled[1] Keypad Lockout enabledEnter Description[0] to [255] Cards’ Family Code
PosiPin 9READER’S INTERFACESection [007][007][007][007] - Default: [0][0][0][0]The reader component of the PosiPin must be programmed to usethe same reader communication format as the controller. CHECK-IN SUPERVISIONSection [008][008][008][008] - Default: [0][0][0][0]This feature only applies when the communication formatprogrammed in Section [002] is set for Option [1]: 26-bitWiegand or Option [2]: 37-bit Wiegand.When no actions are performed on the PosiPin for a period of time,it will communicate its status to the controller every 30 seconds bysending a code to confirm its presence (26-bit Wiegand =255:65535; 37-bit Wiegand = 65535:65535). If the PosiPin doesnot communicate its status every 30 seconds, the controller can beprogrammed to generate an alarm.Enter Description[0] 26-bit Wiegand[1] 37-bit WiegandEnter Description[0] Check-in Supervision disabled[1] Check-in Supervision enabled
10 Installation and Operating InstructionsBUZZER SETTINGSection [101][101][101][101] - Default: [3][3][3][3]The number of beep tones emitted as a response to a card beingpresented to the reader can be adjusted from 0 (disabled) to 7 (7rapid beep tones).FACE LIGHT INTENSITYSection [102][102][102][102] - Default: [4][4][4][4]The Face Light’s illumination can be adjusted according to theinstallation’s requirements from 0 (extinguished) to 8 (brightest). FACE LIGHT OPERATIONSection [103][103][103][103] - Default: [1[1[1[1]The Face Light can be set to remain illuminated continually or canfollow the Status LEDs’ state. Enter Description[0] to [7] Number of beep tones per responseEnter Description[0] to [8] Face Light’s intensity level Enter Description[0] Face Light constant[1] Face Light follows Status LEDs
PosiPin 11FACE LIGHT COLOURSection [104][104][104][104] - Default: [0][0][0][0]The Face Light’s colour can be red or green as desired.This feature only applies when Face Light Operationprogrammed in Section [103] is set for Option [0]: Face Lightconstant. CHANGING THE INSTALLER CODESection [200][200][200][200] - Default: 000000The Installer Code is used to enter PosiPin’s programming mode.The Installer Code is six digits long where each digit can be anyvalue from 0 to 9.PANIC ALARMA panic code can be generated and transmitted to the controller bypressing and holding the [CLEAR] and [ENTER] keys for 2 seconds(26-bit Wiegand = 255:65534; 37-bit Wiegand = 65535:65534). This feature only applies when the communication formatprogrammed in Section [002] is set for Option [1]: 26-bitWiegand or Option [2]: 37-bit Wiegand.Enter3 Description[0] Red Face Light [1] Green Face Light
12 Installation and Operating InstructionsRESETTING TO DEFAULTTo reset PosiPin to factory defaults, disconnect its power supply.Press and hold the [1] and [2] keys simultaneously while re-connecting its power supply.CARD PRESENTATION TESTPresent the card to the reader as shown in the figure below. Placethe card parallel to the PosiPin reader and move it toward thereader until the card code displays on the controller screen. At thispoint, the card is read, decoded, data transmitted to the controllerand the controller has responded accordingly. To read the cardagain, remove and re-insert the card into the reader's field.
WARRANTYThe Seller warrants its products to be free from defects inmaterials and workmanship under normal use for a period of oneyear. Except as specifically stated herein, all express or impliedwarranties whatsoever, statutory or otherwise, including withoutlimitation, any implied warranty of merchantability and fitness fora particular purpose, are expressly excluded. Because Sellerdoes not install or connect the products and because theproducts may be used in conjunction with products notmanufactured by Seller, Seller cannot guarantee theperformance of the security system. Seller obligation and liabilityunder this warranty is expressly limited to repairing or replacing,at Seller's option, any product not meeting the specifications. Inno event shall the Seller be liable to the buyer or any otherperson for any loss or damages whether direct or indirect,consequential or incidental, including without limitation anydamages for lost profits stolen goods or claims by any otherparty caused by defective goods or otherwise arising from theimproper, incorrect or otherwise faulty installation or use of themerchandise sold.
Printed in Canada 04/2001PPINEI-00

Navigation menu