Power Idea Technology RG850 LTE Smartphone User Manual

Download:
Mirror Download [FCC.gov]
Document ID	4029035
Application ID	eMy18N52HhgMiRz0qFYrUA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	128.56kB (1607020 bits)
Date Submitted	2018-10-08 00:00:00
Date Available	2018-10-08 00:00:00
Creation Date	2018-09-25 16:00:48
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2018-10-08 15:08:39
Document Title	RG850全球通用版英文版FCC说明书（料号：24016602）2018-07-16.indd
Document Creator	Adobe InDesign CC 13.0 (Windows)

2
10
11
SIM/MICRO SD
1.
2.
3.
4.
SIM
icro
SD
ENGLISH
KEYS AND SPECIAL FEATURES (see illustration on page 2)
1_EARPHONE JACK
2_SECONDARY MIC
3_VOLUME UP/DOWN
4_POWER KEY: Long press to power ON/OFF the device.
Short press to power ON/OFF the screen.
5_MAIN MICROPHONE
6_USB-C 2.0 PORT: For charging the phone and to connect to
other devices with the included USB cable.
7_FRONT CAMERA
8_FRONT SPEAKER
9_SIM CARD TRAY
10_MAIN CAMERA
11_CAMERA FLASH / TORCH
1. INTRODUCTION
This document contains information and safety regulations which are to be
observed without fail for safe operation of the device RG850 under the described
conditions. Non-observance of this information and instructions can have serious
consequences and/or may violate regulations.
Please read the manual and these safety instructions before using the device. In
case of any doubt, the English version shall apply.
The current EU-declaration of conformity, safety instructions and manuals can
be found at www.ruggear.com, or requested from Power Idea Technology
(Shenzhen) Co., Ltd.
2. RESERVATION
The content of this document is presented as it currently exists. Power Idea
Technology (Shenzhen) Co., Ltd. does not provide any explicit or tacit guarantee
for the accuracy or completeness of the content of this document, including, but
not restricted to, the tacit guarantee of market suitability or fitness for a specific
purpose unless applicable laws or court decisions make liability mandatory.
Power Idea Technology (Shenzhen) Co., Ltd. reserves the right to make
changes to this document or to withdraw it any time without prior notice.
Changes, errors and misprints may not be used as a basis for any claim for
damages. All rights reserved.
Power Idea Technology (Shenzhen) Co., Ltd. cannot be held responsible for
any data or other loss and direct or indirect damages caused by any improper
use of this device.
3. EU-DECLARATION OF CONFORMITY
The EU-declaration of conformity can be found at the end of this manual.
4. FAULTS AND DAMAGES
If there is any reason to suspect that the safety of the device has been
compromised, it must be withdrawn from use immediately. Measures must be
taken to prevent any accidental restarting of the device. The safety of the device
may be compromised, if, for example:
• Malfunctions occur.
• The housing of the device shows damage.
• The device has been exposed to excessive loads.
• The device has been stored improperly.
• Markings or labels on the device are illegible.
We recommend that a device displaying errors or in which an error is suspected
be sent back to Power Idea Technology (Shenzhen) Co., Ltd. to be checked.
5. FURTHER SAFETY ADVICE
• Do not touch the screen of the device with sharp objects. Dust particles and
nails may scratch the screen. Please maintain the screen clean. Remove dust on
the screen with a soft cloth gently, and do not scratch the screen.
• Do not put the device in environments with excessive temperatures, as this
• Do not charge the device in environments with much dust or humidity.
• Do not use the device in areas where regulations or legislatives prohibit the use.
• Do not expose the device or charger to strong magnetic fields, such as are
emitted from induction ovens or microwaves.
• Do not attempt to open or repair the device. Improper repair or opening can
lead to the destruction of the device, fire or explosion. Only authorized
personnel are allowed to repair the device.
• Only use accessories approved by Power Idea Technology (Shenzhen) Co.,
Ltd.
• Power off the device in hospitals or other places where the use of mobile
phones is prohibited. This device may affect proper work of medical equipment,
such as pacemakers. Always keep a distance of at least 15 cm between the
device and these devices.
• Make sure the volume level is not set too high when plugging
earphones and headphones to protect your hearing.
• Observe all corresponding laws that are in force in the respective countries
regarding the use of devices while operating a vehicle.
• Please power off the device and disconnect the charging cable before cleaning
the device.
• Do not use any chemical cleaning agents to clean the device or the charger. Use
a damp and anti-static soft cloth for cleaning.
• Adapter shall be installed near the equipment and shall be easily accessible.
• The product shall only be connected to a USB interface of version USB2.0.
• Do not discard old and abandoned lithium batteries into the trash, send them
to designated waste disposal locations.
• The user alone is responsible for any and all damages and liabilities caused by
malware down-loaded when using the network or other data-exchange
functions of the device. Power Idea Technology (Shenzhen) Co., Ltd. cannot
be held responsible for any of those claims.
Warning
Power Idea Technology (Shenzhen) Co., Ltd. will not assume any liability for
damages caused by disregarding any of these advices or by any inappropriate
use of the device.
6. MAINTENANCE/REPAIR
Please note any legal requirements for periodic inspection. The device itself has
no user-serviceable parts. It is recommended to perform inspections according
to the safety regulations and advises. If there is a problem with the device, please
contact your vendor or consult the service center. If your device is in need of
repair, you can either contact the service center or your vendor.
7. BATTERY
The battery is not fully charged when the device is purchased, but it contains
enough energy to power on the device. To obtain best battery performance and
battery life, let the battery discharge completely before charging it completely for
the first three charging cycles.
The device may only be charged at ambient temperatures in a range from +5°C
... +35°C. The phone's normal operating temperature is -20 °C to +55 °C. In
order to ensure the normal phone functions, do not use this phone outside the
temperature range.
Caution:
Risk of explosion if battery is replaced by an incorrect type. Dispose used
batteries according to the instructions.
RG850 supports 5V/2A charging, using any higher charging current may damage
your phone.
8. INSTALLATION OF THE NANO SIM CARD (see illustration on page 2)
The device has two slots for nano SIM cards. This is located on the left side of the
unit. Use the ejector pin to access the SIM card slot until the SIM card tray ejects.
Warning
Do only change the SIM card when the device is switched off. Do not try to insert
or remove the SIM card when any external power supply is connected, otherwise
the SIM card may be damaged.
9. INSTALLATION OF THE MICROSD CARD (see illustration on page 2)
The device supports microSD card (up to 128GB). It located in the SIM card tray.
SIM slot 2 can support either a microSD card or an additional SIM card. Example:
one SIM card and microSD, or two SIM cards and no microSD.
EN
Warning
Do only change the microSD card when the device is switched off. Do not try to
insert or remove the microSD card when any external power supply is connected,
otherwise the microSD card may be damaged.
10. RECYCLING
The crossed-out wheeled-bin symbol on your product, battery, literature, or
packaging reminds you that all electrical and electronic products, batteries, and
accumulators must be taken to separate collection at the end of their working
life. This requirement applies in the European Union. Do not dispose of these
products as unsorted municipal waste.
Always return your used electronic products, batteries, and packaging materials
to dedicated collection points. This way you help prevent uncontrolled waste
disposal and promote the recycling of materials.
More detailed information is available from the product retailer,
local waste authorities, national producer responsibility
organisations, or your local Power Idea Technology
(Shenzhen) Co., Ltd. representative.
11. INFORMATION CONCERNING CE SAR CERTIFICATION
(Specific Absorption Rate)
The SAR limit of Europe is 2.0 W/kg. The device has also been tested against this
SAR limit. The highest SAR value reported under this standard during product
certification for use at the ear is 0.762 W/kg and when properly worn on the
body is 1.027 W/kg. This device was tested for typical body-worn operations with
the back of the handset kept 5mm from the body. The device complies with RF
specifications when the device used at 5mm from your body. The use of belt
clips, holsters and similar accessories should not contain metallic components in
its assembly. The use of accessories that do not satisfy these requirements may
not comply with RF exposure require- ments, and should be avoided.
12. FCC CAUTION
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
SPECIFIC ABSORPTION RATE (SAR) INFORMATION
SAR tests are conducted using standard operating positions accepted by the
FCC with the phone transmitting at its highest certified power level in all tested
frequency bands, although the SAR is determined at the highest certified power
level, the actual SAR level of the phone while operating can be well below the
maximum value. Before a new model phone is a available for sale to the public,
it must be tested and certified to the FCC that it does not exceed the exposure
limit established by the FCC, tests for each phone are performed in positions and
locations as required by the FCC.
For body worn operation, this model phone has been tested and meets the FCC
RF exposure guidelines when used with an accessory designated for this product
or when used with an accessory that contains no metal and that positions the
handset a minimum of 1.0cm from the body. Non-compliance with the above
restrictions may result in violation of RF exposure guidelines
ISEDC WARNING
This device complies with ISEDC license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'ISEDC applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes :
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
SAR tests are conducted using standard operating positions accepted by the
ISEDC with the phone transmitting at its highest certified power level in all tested
frequency bands, although the SAR is determined at the highest certified power
level, the actual SAR level of the phone while operating can be well below the
maximum value. Before a new model phone is a available for sale to the public,
it must be tested and certified to the ISEDC that it does not exceed the exposure
limit established by the ISEDC, tests for each phone are performed in positions
and locations as required by the ISEDC.
For body worn operation, this model phone has been tested and meets the ISEDC
RF exposure guidelines when used with an accessory designated for this product
or when used with an accessory that contains no metal and that positions the
handset a minimum of 1.0cm from the body. Non-compliance with the above
restrictions may result in violation of RF exposure guidelines
Le présent appareil est conforme
Après examen de ce matériel aux conformité aux limites DAS et/ou aux
limites d’intensité de champ RF, les utilisateurs peuvent sur l’exposition aux
radiofréquences et la conformité and compliance d’acquérir les informations
correspondantes.
13. TRADEMARKS
• Google™, Google Play and Android are trademarks of Google Inc.
• All other trademarks and copyrights are the properties of their respective
owners.
EN
Power Idea Technology (Shenzhen) Co., Ltd.
4th Floor, A Section, Languang Science&technology
Building, No.7 Xinxi RD, Hi-Tech Industrial Park North,
Nanshan District, ShenZhen, P.R.C.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Create Date                     : 2018:09:25 16:00:48+08:00
Creator                         : Adobe InDesign CC 13.0 (Windows)
GTS PDFX Conformance            : PDF/X-3:2002
GTS PDFX Version                : PDF/X-3:2002
Modify Date                     : 2018:10:08 15:08:39-07:00
Language                        : zh-CN
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2018:10:08 15:08:39-07:00
Creator Tool                    : Adobe InDesign CC 13.0 (Windows)
Instance ID                     : uuid:221935cc-d7a4-4d81-9546-6d619e9cf2ed
Original Document ID            : xmp.did:141af377-b7e6-f74d-8572-fa4283027a3e
Document ID                     : xmp.id:2320ddd5-d21d-044f-ad33-e189d284058e
Rendition Class                 : proof:pdf
Version ID                      : 1
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 13.0 (Windows)
History Changed                 : /
History When                    : 2018:09:25 16:00:48+08:00
Derived From Instance ID        : xmp.iid:ac73aa3d-4051-6047-8c3a-e7ab3f3fc157
Derived From Document ID        : xmp.did:141af377-b7e6-f74d-8572-fa4283027a3e
Derived From Original Document ID: xmp.did:141af377-b7e6-f74d-8572-fa4283027a3e
Derived From Rendition Class    : default
Format                          : application/pdf
Title                           : RG850全球通用版英文版FCC说明书（料号：24016602）2018-07-16.indd
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 7

EXIF Metadata provided by EXIF.tools