Powerkiss WCT12W Wire-free charging solutions User Manual positioning guide

Powerkiss Oy Wire-free charging solutions positioning guide

Contents

positioning guide

PowerKissWire-freeCharging
2PowerKiss Hotspot Positioning Guide© PowerKiss 2011
3ContentsPowerKiss wire-free charging 4 Ring 4 Heart 4Processing 5Technical requirements 6 I Furniture material 6 II Distance from the user 7 III Space required by PowerKiss Heart 8 IV Distance between two Hearts 9Fine tuning the place for the Hotspot 10 I Optimal place for the Hotspot 10 II Taking adjacent seats into account 11 III The Edges 12Examples of positioning the PowerKiss Hotspots 13 Round table 13 Conference table 14 A single-user worktable 15Summary of the requirements 16
4HeartTo turn a surface into a wire-free charging platform it first needs to be given a Heart. Like most, this Heart is also hidden except for a small LED light to indicate that it is ready to charge a mobile device wearing a Ring. The LED is also the center point of the charging area, called PowerKiss Hotspot. Whenever the device with Ring is on this Hotspot, the wire-free charging begins. PowerKiss wire-free chargingThe essence of wire-free charging is the pairing of Heart and Ring. The Heart is the transmitter and the Ring is the receiver and together they enable wire-free charging on almost any surface.RingThe Ring is a small accessory that is plugged into handheld devices, such as mobile phones or mp3-players. As soon as the Ring is plugged in, the device is ready to be a part of a wire-free energy transaction. I.T.E.Wire-free Charging TransmitterIn put: 12 ± 0. 2 V D C / 1 .0 A / 12 WIn doo r use on lyVersion: 2.1 S/N : A00500Heart+-FCC ID: ZMI-WCT12WUse only with power supplies listed in the manual
Processing As was mentioned in the foreword, the Heart is installed to a piece of furniture. There is a special milling that needs to be done in order to use the Heart properly. Drawings of the milling are presented in pictures below.34±168±1A A4±0,53,5+0,1SECTION A-ARout out dimensionstable_samplePowerKiss Oy12.1.2011talWEIGHT: A4SHEET 1 OF 1SCALE:1:2FILE NAME:PART NUMBER/DESCRIPTION:REVISIONDO NOT SCALE DRAWINGMATERIAL:DATESIGNATURENAMEDEBUR AND BREAK SHARP EDGESFINISH:UNLESS OTHERWISE SPECIFIED:DIMENSIONS ARE IN MILLIMETERSSURFACE FINISH:TOLERANCES: LINEAR: ANGULAR:Q.AMFGAPPV'DCHK'DDRAWN
6Technical requirementsI Furniture materialDue to the characteristics of electromagnetic fields,PowerKiss wire-free charging equipment should not be inserted into metal surfaces, or other conductive or highly magnetic materials. Also, because of the heating of the PowerKiss Heart and Ring, the material in which the equipment is inserted, should be heat tolerant at 80°C. This applies also for the coating material of the surface. The PowerKiss Heart is designed to be installed into a piece of furniture with surface thickness of 15-50mm.• Heat tolerant at 80°C• Target surface thickness of 15-50 mm• Not containing metal or conductive materialFurniture material should be
7This matter of attention applies to such special cases as special structures of pieces of furniture and solutions designed to be positioned to the immediate vicinity of the user.Technical requirementsII Distance from the userDue to the characteristics of electromagnetic fields, PowerKiss Hotspot must not be positioned so that the center of the charging area is continuously closer than 250mm from the user's body in vertical direction and 200mm in horizontal direction.• 250mm in vertical direction • 200mm in horizontal direction Required distance between user and Hotspot
8One should also remember that Heart must finally be plugged into a power supply, which means that there must also be space for a power cable.Technical requirementsIII Space required by PowerKiss HeartThe installation of PowerKiss Heart requires a certain amount of space, which should be taken into account before the actual processing of the table. HotspotØ 68 mmHeart dimensions• Width: 132mm• Length: 162mm• Height: 24mm• Weight: 135gPower supply port
9Technical requirementsIV Distance between two HeartsIf the plan is to install several Hearts into a single surface, attention must be paid to their distance from each other. The distance between two Hearts must be at least 300mm. The distances should be measured from the center of the Hotspots.Min. 300mm
10400mm200mmFine tuning the place for the HotspotI Optimal place for the HotspotWhen it comes to tables, users usually place their small devices, such as mobile phones, to the right and front. The recommended centre position of the PowerKiss Hotspot is 400mm to the right of the sitting position and 200mm from the edge of the piece of furniture, as presented in image below.The goal is to place the Hotspot in a position where the user can easily reach while also making sure that the area does not disturb the primary use of the table (such as eating or work).Optimal place for the Hotspot
11Fine tuning the place for the HotspotII Taking adjacent seats into accountEnsure that the Hotspots do not cross to the working areas of another users (in the area of another seating position), If needed, change the distance so that the area will be closer to the centre of the seating position of the user for whom the area is being established. 300mm200mm400mm200mmOK!300mm200mm
12Fine tuning the place for the HotspotIII The Edges The centre of the Hotspot should be positioned so that there would be 200mm minimum distance from the egdes, in order to avoid dropping the devices being charged and to ensure distance between the user and the Hotspot (see page 7).OK!400mm200mm400mm200mm
13There are a few examples below of tables of different shapes and types and related examples of Hotspot positioning..Examples of positioning the PowerKiss HotspotsThere are various matters that affect the design of a Hotspot positioning. These include aesthetics, materials, usage and manufacturing procedures. One should always remember that without a proper positioning, the piece of furniture fails to provide its feature of wire-free charging. A completely round table with a diameter of 1,250mm.OK!400mm200mm400mm200mm
14OK!300mm200mm300mm200mm530mm450mm300mm200mm150mm400mmA 2,600mm x 1,060mm conference table
15A single-user worktable with one Hotspot, dimensions: 2,000mm x 2,500cmOK!400mm200mm
16Summary of the requirements1. Furniture material requirements Target surface thickness of 15-50 mm Heat tolerant at 80°C Not containing metal or other conductive material2. Required distances (from center of the Hotspot) From the user's body - vertically 250mm From the user's body - horizontally 200mm To another Hotspot 300mm3. Reserve an area for the installation of the Heart around the Hotspot4. Place the Hotspot so that it is in front and right of the user. Recommended: 400mm to the right of the center of the sitting position and 200mm from the edge of the piece of furniture5. Do not place the Hotspot in an area meant for another user or near the edges of the surface
17
www.powerkiss.cominfo@powerkiss.com© PowerKiss 2011

Navigation menu