Powertech Co R9P005 Wireless Home Appliance Remote Control Kit User Manual RF Good
Powertech Industrial Co Ltd Wireless Home Appliance Remote Control Kit RF Good
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1258601 |
| Application ID | V/PK8zNrS3Ot9XqWDAeBLg== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 45.26kB (565810 bits) |
| Date Submitted | 2010-03-29 00:00:00 |
| Date Available | 2010-03-29 00:00:00 |
| Creation Date | 2010-01-04 19:21:35 |
| Producing Software | Adobe PDF library 8.00 |
| Document Lastmod | 2010-03-23 17:20:50 |
| Document Title | RF Good |
| Document Creator | Adobe Illustrator CS3 |
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ＊Reorient or relocate the receiving antenna. ＊Increase the separation between the equipment and receiver. ＊Connect the equipment into an outlet on a circuit different from that to which the receiver is needed. ＊Consult the dealer or an experienced radio/TV technician for help. Service Center in USA Company’s name: Haowell Technology & Consulting, Inc. Address: 415 Cloverdale Ln. Walnut, CA 91789-2028 phone no: 909-859-5150 Fax no: 909-468-4660 Contact person: Shannon Chang E-mail: Shannon@HaowellConsultants.com Wireless Home Appliance Remote Control Kit R9P-005 R9P-006 R9P-119 R9P-402 R9P-119 R9P-402 User’s Manual © Copyright 2010 The information contained herein is subject to change without notice. This document contains proprietary information, which is protected by copyright. No part of this document may be photocopied, reproduced, All Versions or translated into another language without the prior written consent. February 2010 INTRODUCTION Operating Instruction - Outlet Adaptor THANK YOU for purchasing Wireless Home Appliance Remote Control Kit, you can remotely control indoor or outdoor fixtures and appliances from up to 100ft away (in open space). 1. Plug the outlet adaptor into a powered 125VAC wall outlet. 2. Plug the fixture / appliances you wish to control into 1 outlet wall tap / wall tap plus or the remote outlet of the yard stake. 3. Turn the mechanical power switch (electrical power switch is not applicable) of the fixture / appliance to the ON position. 4. Use the remote control to turn ON/OFF the fixture/appliance (see the operating instruction – remote control in below). Having your holiday lighting or appliances turned ON & OFF is just as easy as few clicks on the remote control. Our product can conveniently help to change your house into an easy home automation style. OPERATING INSTRUCTIONS NOTE: There are four types of Wireless Home Appliance Remote Control Kit available that best suits your needs. The remote control and outlet adaptor may vary depending on the kit model purchased. Indoor Use R9P-117 Outdoor Use R9P-118 IMPORTANT: ● Outdoor use outlet adaptor is recommended plugged into a GFCI-protected outlet. ● Outdoor use outlet adaptor is suitable for damp locations. Not for water immersion or for use where directly exposed to water. ● Yard stake outlet adaptor should be installed above ground level so it will not fill up with water when raining or snowing. Always unplug and remove the devices from the yard stake when raining or snowing. Indoor & Outdoor Use R9P-402 R9P-109 Operating Instruction – Wireless Remote Control In open space, the remote control has a wireless range up to 100 feet* to control the outlet adaptor. *Actual range may vary depending on environment condition, interference and building materials. To turn ON and OFF the lighting fixture/appliance 1-Outlet Wall Tap with remote control Versions V1.0 1-Outlet Wall Tap Plus with remote control 4-Outlets Yard Stake (2 always on / 2 remote outlets) with remote control 1-Outlet Wall Tap + 1-Outlet Wall Tap Plus with 4 key remote control 1. To turn ON the lighting fixture/appliance, press ON switch on the remote control. The red LED indicator on the remote control will flash and the lighting fixture/appliance on the outlet adaptor will turn ON. Versions V1.0 2. To turn OFF the lighting fixture/appliance, press OFF switch on the remote control. The red LED indicator on the remote control will flash and the lighting fixture/appliance on the outlet adaptor will turn OFF. Remote Control 1. Power on indicator 2. Outlet Adaptor ON and OFF indicator - the red LED Replace battery in the remote control indicator will show when you turn ON the device, and disappear when you turn OFF the device One A23 12V Alkaline battery is included and pre-installed in the remote control. Replace the battery when the red LED light on the remote control goes very dim or does not illuminate while operating. OFF the device 4. OFF Switch Model No. R9P005 Remove the battery compartment cover on the back of the remote control, take out the old battery and insert one A23 12V Alkaline battery in the proper orientation, and re-install the battery compartment cover. Wall mount for remote control 1. Select a spot within the wireless range to mount the supplied wall bracket for remote control. 2. The ideal locations for wall mount are entrance of a room or location where remote control wall mount can be easily seen and accessed. 3. Use adhesive tape or supplied screws to securely attach the supplied wall bracket to a wall. 3. ON Switch Battery Type Use ONLY A23 12V Alkaline Battery Life 3-6 months Power on indicator Red LED Wireless Range Up to 100ft (Open Space) 4 Key Remote Control 1. Power on indicator 2. Outdoor use outlet adaptor ON and OFF indicator 3. ON Switch for outdoor use outlet adaptor 4. OFF Switch for outdoor use outlet adaptor SPECIFICATIONS 5. Indoor use outlet adaptor ON and OFF indicator 6. ON Switch for indoor use outlet adaptor 7. OFF Switch for indoor use outlet adaptor Model No. R9P006 Battery Type Use ONLY A23 12V Alkaline Battery Life 3-6 months Power on indicator Red LED Wireless Range Up to 100ft (Open Space) Versions V1.0 Versions V1.0 Indoor Use - Wall Tap 1. Power on indicator 2. Remote Outlet Outdoor Use – 4-outlet Yard Stake 1. Power on indicator 2. Remote outlets on both side Model No. R9P115R0 3. Always On outlets on both side Electrical Rating 15A / 125V, 60Hz Resistive Load 1875W Remote Outlet Power on indicator Red LED Stand-by power <1W Model No. R9P401R0 Outdoor Use - Wall Tap Plus 1. Power on indicator 2. Remote Outlet Electrical Rating 15A / 125V, 60Hz Resistive Load 1875W Remote Outlet Always On outlet Power on indicator Red LED Stand-by power <1W Model No. R9P116R0 Electrical Rating 13A / 125V, 60Hz Resistive Load 1625W Remote Outlet Power on indicator Red LED Stand-by power <1W Versions V1.0 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Versions V1.0
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.1-c036 46.277092, Fri Feb 23 2007 14:16:18 Format : application/pdf Title : RF Good Creator Tool : Adobe Illustrator CS3 Create Date : 2010:01:04 19:21:35+08:00 Modify Date : 2010:03:23 17:20:50+08:00 Metadata Date : 2010:03:23 17:20:50+08:00 Thumbnail Width : 184 Thumbnail Height : 256 Thumbnail Format : JPEG Thumbnail Image : (Binary data 16042 bytes, use -b option to extract) Document ID : uuid:51255F04F8FADE1198A1A6BBB6A9972E Instance ID : uuid:7d291e4f-d8fe-c54d-9b5c-1b1fe17313bf Derived From Instance ID : uuid:50255F04F8FADE1198A1A6BBB6A9972E Derived From Document ID : uuid:0898544419F6DE11813884E08B4FFA82 Startup Profile : Basic CMYK N Pages : 1 Has Visible Transparency : True Has Visible Overprint : False Max Page Size W : 210.000145 Max Page Size H : 297.000089 Max Page Size Unit : Millimeters Font Name : DINOT-Bold, DIN-Regular, DIN-Black, DIN-Bold, LiGothicMed, AdobeMingStd-Light Font Family : DINOT, DIN, DIN, DIN, 蘋果儷中黑, Adobe 明體 Std Font Face : Bold, Regular, Black, Bold, 中黑, L Font Type : Open Type, Type 1, Type 1, Type 1, TrueType, Open Type Font Version : Version 7.460;PS 7.046;hotconv 1.0.38, 001.000, 001.000, 001.000, 6.0d1e1, Version 5.003;PS 5;hotconv 1.0.49;makeotf.lib2.0.14802 Font Composite : False, False, False, False, False, False Font File Name : DINOT Bold.otf, DINReg; DIN-Regular, DINBla; DIN-Black, DINBol; DIN-Bold, Apple LiGothic Medium.dfont, AdobeMingStd-Light.otf Plate Names : Cyan, Magenta, Yellow, Black Swatch Group Name : Default Swatch Group Swatch Group Type : 0 Producer : Adobe PDF library 8.00 Has XFA : No Page Count : 2 Creator Version : 13 Container Version : 11 Creator : Adobe Illustrator(R) 13.0 For : olivea, Bounding Box : 0 0 596 842 Image Height : 842 Image Width : 596 Image Size : 596x842 Megapixels : 0.502EXIF Metadata provided by EXIF.tools