Powerwave Technologies 5JS0055 PCS 1900 MHz Single Channel Power Amplifier User Manual Yosemite PCS manual

Download:
Mirror Download [FCC.gov]
Document ID	162377
Application ID	CmAqye++KM+KTnb5wNsGJg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	0.59kB (7427 bits)
Date Submitted	2001-07-31 00:00:00
Date Available	2001-07-31 00:00:00
Creation Date	2001-07-20 15:32:44
Producing Software	Acrobat PDFWriter 4.05 for Windows
Document Lastmod	0000-00-00 00:00:00
Document Title	Yosemite_PCS_manual.PDF
Document Creator	Microsoft Word
Document Author:	cperez

OPERATING INSTRUCTIONS
NTQA50GA
Note: These operating instructions describe the procedure for turning on and off the amplifier
output power using signal generators. This amplifier will be used with transmitters which have been
or will be certified separately. The specific transmitter instruction book should be consulted for the
correct method to use this amplifier with transmitters.
1.
The input voltage range, applied to pin A1 of the DC input connector, should be between –36VDC and
–57 VDC. Pin A2 and A3 of the connector should be grounded.
2.
Pin 5 of the Data I/O connector should be grounded to enable operation of the amplifier without the
data interface. Pins 1, 2, 11, and 12 on the Data I/O connector are connected to ground. Operation
with the Data I/O interface can only be performed using the transmitter software. See the transmitter
manual for instructions.
3.
Connect the RF signal generator to the RF input port.
4.
Connect the RF output port to the measurement equipment. Make sure the measurement equipment is
capable of handling 33 watts, or use a power attenuator or directional coupler to attenuate the signal to
a level the equipment can handle.
5.
To turn on the amplifier, first apply the DC voltage with the specified range (-48 VDC nominal).
6.
Apply RF power from the signal generator. Adjust the RF input power until the desired RF output
power is achieved. The amplifier’s maximum RF output power rating is 33 watts (+45.2 dBm)
7.
The gain may change up to 0.5 dB as the amplifier temperature stabilizes after turn-on. Let the
amplifier warm up for 10-30 minutes, then re-adjust the power to compensate for the gain change.
8.
The amplifier is now operational.
SPECIFICATIONS
Parameter
Specification
Operating Frequency
Rated Output Power
Gain at Full Power
Input Voltage Range
Maximum DC Power Consumption
Channeling
Modes of Transmission
Type of Modulation
1930 to 1990 MHz
+45.2 dBm (33 Watts)
48 +/- 1 dB
-36 to –57 VDC
230 Watts
Controlled by transmitter
GSM or EDGE
Not applicable (performed by transmitter)
Occupied Bandwidth and Emissions Designators
Emissions Type
Amplitude
GSM (300KGXW)
-30 dBc
-33 dBc
-60 dBc
-70 dBc
-73 dBc
-75 dBc
-80 dBc
Frequency Removed from Carrier
200 kHz
250 kHz
400 kHz
600 kHz
1200 kHz
1800 kHz
6000 kHz
EDGE (300KG7W)
-30 dBc
-33 dBc
-56 dBc
-70 dBc
-73 dBc
-75 dBc
-80 dBc
200 kHz
250 kHz
400 kHz
600 kHz
1200 kHz
1800 kHz
6000 kHz

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 2
Creator                         : Microsoft Word
Create Date                     : 2001:07:20 15:32:44
Title                           : Yosemite_PCS_manual.PDF
Author                          : cperez
Producer                        : Acrobat PDFWriter 4.05 for Windows

EXIF Metadata provided by EXIF.tools