Prastel S p A TP2E GARAGE DOOR REMOTE CONTROL User Manual ISMPSTP2E 03 08

Download:
Mirror Download [FCC.gov]
Document ID	928080
Application ID	t8XMwuF5kUyp5M2c/pZS5A==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	4.57kB (57075 bits)
Date Submitted	2008-04-15 00:00:00
Date Available	2008-04-16 00:00:00
Creation Date	2008-03-20 13:58:35
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2008-03-20 13:58:35
Document Title	Microsoft Word - ISMPSTP2E_03_08.DOC
Document Creator	PScript5.dll Version 5.2
Document Author:	alberto.gamberini

MPSPTP2E
CAUTION FOR THE USER
Any change or modification of the product is forbidden if not expressly approved by
the manufacturer
GENERAL INFORMATION The MPSPTP2E 2 channel transmitter transmits the rolling security code at 433 MHz
and is fitted with a remote self-learning function on the receiver. It is powered by a lithium 3V battery (size
CR2032).
Intended use of the equipment: radio transmitter in garage-door systems.
Typical use of the equipment: the equipment is not foreseen for continuous operations
CHANNEL SELECTION
1. For channel 1 press button 1, for channel 2 press button 2 (fig.1)
ENTERING THE TRANSMITTER IN THE MEMORY OF THE RECEIVER
1. Press the programming button on the receiver; the red LED lights up.
2. Press the button corresponding to the transmitter channel to be memorised; the code is set in memory. During
the insertion, the receiver LED flashes for about two seconds, then returns to the steady light state to indicate that
a new transmitter can be entered.
When the operation is completed, press the programming button on the receiver again to exit from the procedure,
the LED goes out. The exit from the procedure is automatic after 10 seconds from the last insertion of a
transmitter.
REMOTE ENTERING OF NEW TRANSMITTERS IN THE MEMORY OF THE RECEIVER (RPA FUNCTION)
1. Approach the receiver (1-2m) with an already programmed transmitter.
2. Press buttons 1 & 2 at the same time then release them; the LED lights up and after about 2 seconds goes out.
3. When the LED lights up again, press buttons 1 & 2 at the same time again and keep them pressed until the LED
starts flashing alternatively red-green.
4. At the end of flashing, the TX sends a transmission which activates the learning function of the receiver
5. The receiver waits 10 seconds for transmissions from new transmitters. Press one of the buttons of the
transmitter to be learned. The receiver stores the new transmitter into its memory.
6. During the learning procedure, the 10 seconds learning timeout is restored at any new transmitter learned.
LOW BATTERY INDICATION
When the battery is running out, it is signalled by a short flash every 5 minutes. It is advisable to replace the
battery before it becomes completely flat.
MPSPTP2E
REPLACEMENT OF THE BATTERIES
Loosen screw A (fig. 3) and open the remote control.
Fit new battery taking care of aligning polarity correctly (fig. 4).
During the operation, handle the battery as shown in fig. 5.
FCC ID: ON3TP2E
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Via del Vetraio, 7
40138 Bologna – ITALIA
Tel. +39 051 6023 311
Fax: +39 051 538 460
http://www.prastel.com
e-mail: info@prastel.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 2
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:5c318cab-daa3-4293-b769-64101ae57d21
Producer                        : Acrobat Distiller 6.0 (Windows)
Create Date                     : 2008:03:20 13:58:35+01:00
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2008:03:20 13:58:35+01:00
Document ID                     : uuid:c1d43243-1e34-4050-985c-9a84f3908d5a
Format                          : application/pdf
Title                           : Microsoft Word - ISMPSTP2E_03_08.DOC
Creator                         : alberto.gamberini
Author                          : alberto.gamberini

EXIF Metadata provided by EXIF.tools