| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2151528 |
| Application ID | 52qT/cRaDHz8EUl5s28vAg== |
| Document Description | USERS MANUAL |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 49.39kB (617387 bits) |
| Date Submitted | 2013-12-26 00:00:00 |
| Date Available | 2013-12-26 00:00:00 |
| Creation Date | 2013-12-23 15:11:32 |
| Producing Software | Acrobat Distiller 7.0 (Windows) |
| Document Lastmod | 2013-12-23 15:11:32 |
| Document Title | Microsoft Word - _FCC&IC_Manual.doc |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | Maikou.Zhang |
PERFORMANCE
Wireless Backup Camera System
Model N0.:ACA020&ATBOOO
Owner’s Manual
and Warranty Information
Read these instructions completely before using this product.
Retain this Owner’s Manual for future reference.
SAFETY PRECAUTIONS
AThIs safety alert symbol indicates that a potential personal injury hazard is present. The symbol
is usually used with a signal word (e.g.. WARNING) which designates the degree or level of hazard
seriousness.
The signal word WARNING indicates a hazardous situation which. if not avoided. could result in death
or serious injuw.
The signal word NOTICE indicates a situation which can cause damage to the product, other personal
propeny and/or to the environment. or cause the product to operate improperly.
The combination of the safety alert symbol and signal word is used in safety messages throughout this
manual and on safety labels on this product.
ll safety messages that follow have WARNING level hazards. Failure to
comply could result in death or serious injury.
Back-Up Camera Safety
- Please check with your local and state authorities to confirm what is legal regarding the mounting of
the Back-Up Camera to your vehicle. It is the responsibility of the vehicle owner to understand state
and municipal regulations and ensure compliance.
. When installing the Back-Up Camera, the vehicle must be turned oft with the vehicle in park and the
park brake applied.
- Do not attempt to install the Backap Camera while the engine is operating.
. Do not modify the wiring in any way.
. Only install the Back-Up Camera to a 12-volt DC system. Connecting to anything other than a
12-volt DC system may damage the Back-up Camera components or the vehicle electrical system.
c If you are not confident working with 12-volt DC vehicle wiring. have the BackAUp Camera
professionally installed.
. This device as well as other wireless devices may be subject to interference. Interference may be
caused by cell phones. Bluetooth headsets. Wi-Fi routers. power lines and other various electrical
equipment.
Keep all power cords and wires away from the vehicle's mechanical controls.
Do not mount the monitor where it will interfere with your view of the road.
Do not adjust monitor settings while operating the vehicle.
Do not install the BackeUp Camera to the front of your vehicle.
Do not use in a vehicle which has an alarm or horn when driving in reverse.
Do not paint or spray the camera.
INTRODUCWON
The BackrUp Camera displays images behind the vehicle. and is used when backing up a vehicle.
When the vehicle is driven in reverse. the camera is activated. which sends a signal to the transmitter.
The transmitter sends a video signal to the monitor. which then displays the view captured by the camera.
FEATURES
Color monitor displays View from the rear ol the vehicle
Wireless monitor can be suction-mounted to windshield ordash for easy visibility
Adjustable monitor mounting arm
Adjustable vertical camera angle
Weatherproof camera with 110° viewing angle
Reduces the danger ol harm or damage due to unseen objects
System activates automatically when car is shifted into reverse
Legend
1. Transmitter 8. Hardware Bag
2. Transmitter Power Port 8a) Ties
3. Camera Port 8b) Plastic Grommet
4. Monitor 8c) Vifire Connectors
5. Monitor Power Port 8d) Screws
6. Monitor Arm Be) Locknuts
7. Transmitter Power Cord Bf) Washers
10.
11.
Camera
1A Fuse
Monitor Cigarette Lighter/
Accessory Socket Power
Cord
INST TION
NOTICE Some states or local governments may have regulations or laws that restrict the
use of anything that might impair the clear view of a license plate. Check local laws for
compliance.
NOTICE For the Back-Up Camera to be properly installed, it must be wired into the vehicle's
tallllght harness. If you are not comfortable or knowledgeable with 12-volt DC wiringY have the
system professionally installed.
_These instructions are only meant as a general guide due to the number of
different makes and models of vehicles. For vehicle-specific questions, contact your vehicle's
manufacturer.
4 © 1. Remove the screws that hold the license
,. , plate to the vehicle.
as!!!" 2. Position the camera mounting plate behind
the license plate.
3. Insert the screws through the license plate.
, {0) the camera mounting plate and the
washers. It your hardware is not the correct
length. use the supplied hardware.
Legend
1. Camera
2. Screw Holes
3. Camera Adjusting Screws
_The camera angle should be adjusted to a horizontal position relative to the ground,
so as to provide an optimal view of objects behind the vehicle.
4. Adjust the camera as required:
0 To adjust the camera angle. tilt the camera to one ol the five positions.
0 The camera should be adjusted to a horizontal position relative to the ground, so as to
provide optimal view of objects behind the vehicle.
0 To adjust the camera height. remove the camera adjusting screws. move the camera to line up
with the desired holes and install the camera adjusting screws, Make sure the arrows on the
back of the camera are pointing upward.
5. Install the license plate screws to secure the camera to the vehicle.
6. Determine which are the positive (+) and negative (-) wires for the reverse lights on the vehicle.
You can use either the right- or left-side reverse light wires. For help locating the vehicle‘s reverse
light circuit, contact your vehicle‘s manutacturer tor vehicle-specific wiring diagrams.
Remove the vehicle‘s negative (-) battery cable.
Once the proper wires tor the reverse lights have been determined, the transmitter wires must
be spliced into the vehicle wires using the supplied wire connectors. It you choose to wire
the transmitter using a diflerent method, you must be knowledgeable in 12-volt DC electrical
practices.
5”.“
Legend
Transmitter
Positive (+) Wire from Reverse Light
Wire Connector
Reverse Light
Negative (—) Wire from Reverse Light
Negative (-) Transmitter Power Wire (Black)
Positive (+) Transmitter Power Wire (Red)
Camera
F“>‘975"¥.wl°r‘
9. The red positive (+) wire from the transmitter splices into the positive (+) wire lrom the reverse
lights and the black negative (-) wire lrom the transmitter splices into the negative (-) wire from
the reverse lights.
10. Position the connector around the vehicle wire you are splicing into.
11. Slide the appropriate wire trom the transmitter into the connector.
Legend
1. Wirelrom Vehicle
2. WirelromTransmitter
12. Crimp the metal clamp using a pliers to ensure a good connection and then close the lock of the
wire connector. Do this for both the positive (+) and negative (-) wires trom the reverse light.
13. Mount the transmitter in an area where the wire trom the camera can be plugged into it.
14. Reconnect the vehicle’s negative (-) battery cable.
15. Plug the transmitter power cord plug into the transmitter power port.
Depending on your vehicle type, it may be necessary to drill a hole to route the
camera wire. Betore you drill a hole you MUST CHECK WHAT IS BEHINDTHE DRILLING
LOCATION. It there are any vehicle components, like electrical parts or Iuel system
components, behind the drilling location, you must take precaution not to damage them.
16, Route the wire from the camera to the transmitter. Some vehicles may have a hole to route the
camera wire through; for example. the hole for the wires for the license plate light.
17, It you need to drill a hole, use a 1/2 in. (13 mm) drill to drill the hole. Install the plastic grommet in
the hole. You must use the grommet to prevent the edge of the hole from damaging the camera
wire.
18, Insert the camera wire through the grommet and route it to the transmitter.
19, Plug the camera wire plug into the transmitter camera port and secure the wire with wire ties it
needed.
20, Find a mounting surface inside the vehicle for the monitor where it can be easily seen. but is not
near the rearview mirror assembly or in any other position where it can obstruct your vision when
driving.
NOTE: To maximize the eflectiveness of the suction mount. the mounting location surface
temperature should be between 70° and 100°F (21° and 38°C): avoid application below 50°F
(10°C). Do not perlorm application in direct sunlight.
21. Clean and dry the mounting surface.
22. Press the suction mount against the mounting surtace and push the suction lock lever down.
Make sure it is attached securely.
NOTE: After mounting, protect the mounting suriace lrom direct sunlight for 24 hours.
23. Slide the monitor onto the monitor arm. The monitor angle can be adjusted by loosening the
monitor angle adjustment knobs, tilting the monitor. then tightening the knobs.
24. Plug the monitor cigarette lighter/accessory socket power cord into the monitor power port.
25. Plug the monitor cigarette lighter/accessory socket power cord into a 12
Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.4
Linearized : Yes
XMP Toolkit : 3.1-701
Producer : Acrobat Distiller 7.0 (Windows)
Creator Tool : PScript5.dll Version 5.2.2
Modify Date : 2013:12:23 15:11:32+08:00
Create Date : 2013:12:23 15:11:32+08:00
Format : application/pdf
Title : Microsoft Word - _FCC&IC_Manual.doc
Creator : Maikou.Zhang
Document ID : uuid:00d1826e-193e-4f4a-a52e-5796228cb743
Instance ID : uuid:772b5248-2ad3-4f66-a193-30ce01178a98
Page Count : 8
Author : Maikou.Zhang
EXIF Metadata provided by EXIF.tools