Prime Wire and Cable 002 Remote Control Transmitter User Manual Full page photo

Download:
Mirror Download [FCC.gov]
Document ID	1938714
Application ID	I7/H3bSsbk4CXSxiw3AugQ==
Document Description	QJX-002_user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	26.17kB (327147 bits)
Date Submitted	2013-04-15 00:00:00
Date Available	2013-04-16 00:00:00
Creation Date	2013-03-20 15:53:45
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2013-03-20 15:53:45
Document Title	Full page photo
Document Creator	PScript5.dll Version 5.2.2
Document Author:	wakeyouw

Indoor
Multi-Effects
Light Show
Power
Stand
Model: RCSTM|3
INSTALLATION .
INSTRUCTIONS
I. Connect the two pieces of
the stand together using
the 2 screws (E) to secure
the bracket (c) to the
base to) as shown
2. Mount the Power Center
(B) to the stand With the
outlets racing fronti
aligning the hole in the
bottom of the Power
center to the peg on the
oase. Push the power
Ccntcr into the bracket 50
that it “snaps“ into place.
rr
3%
3. Make sure there is power to the outlet then
plug the fully assembled Power Stand into a
3-er9 grounded indoor outlet Then plug
light strings into each outlet on the Power
StandrThe LED indicator light on the
wireless remote control (A) is lit when the
Power stand is powered on.
PROGRAMMING INSTRUCTIONS
Program the desired lighting effect from the
Wireless remote control or from the push-
outtori on the unit. By activating one of the
following commands on the unit or from the
Wireless remote control. the lights erl do one of
the following:
- Flash : all light strings flash ori/orf rapidly
and simultaneously
- Dim = all light strings dim then brighten
Simultaneously
- Chase = light strings flash on/orf in sequence
by light string
- Fade = light strings dim then brighten in
sequence by light string
- Random Mode 2 light strings run through all
4 basic effects randomly
- on : all lights are on
For full benefit or the effects plugging light
strings into all three outlets is recommended.
lr there are any problems in getting the remote
control to work properly, stop and read the
helprul tips section or these instructions
lf you continue to experience any problems,
please Contact Technical Support toll free at
1755574458955.
BATTERY REPLACEMENT
Use a Phillips Head screw driver to remove the
screw on the battery compartment Pull out the
battery holder to replace one CRZOEZ 3V
Button Cell Battery. Insert CR2032 3V Button
Cell Battery with the "0“ side up. and then
re-insert the battery holder and reinstall the
screw. Dispose of the old battery in compliance
With all applicable laws. Contact your local solid
waste authority ior detailed information
WARNING: Do NOT DISPOSE oF BATTERIES
IN FIRE. BATYERIES MAV EXPLODE OR LEAK.
HELPFUL TIPS
. Make sure the receiver is plugged mm a
working AC outlet.
- Make sure the receiver and connected
equipment are on.
~ Make sure the remote control ON button is
pushed.
- Make sure the (312032. 3v battery in the
remote control is still functioning.
USE I CARE INSTRUCTIONS
- no not mount or place near gas or electric
heaters. fireplaces. candles or other similar
sources or heat,
- Do not secure the Wiring of the product With
staples or nails. or place on Sharp hooks or
nails
- Do not let lamps rest on the power supply
cord or on any Wire
- unplug the product when not in use
- To avoid rlsk of fire, burns or electric shock. it
should not be played With or placed where
small children can reach it.
' Do not use this product for other than its
intended use.
- Do not hang ornaments or other obiects rronri
cord. Wire. or light strings
- Do not close doors or Windows on the
product or extension cords as this may
damage the wire insulation.
- Do not cover the product With cloth. paper or
any material not part of the product when in
use.
- Before using or reusing. inspect product
carefully, Discard any products that have cut.
damaged. or frayed Wire insulation or cords.
cracks in the lampholders or enclosures.
loose connections. or exposed copper ere
- When storing the product. carefully remove
the product from wherever it is placed to
avord any undue strain or stress on the
product conductors, connections. and wires.
- When not in use. store neatly in a cool. dry
location protected from sunlight
- Read and Follow all instructions on the
product or proVided With the product
SAFETY INFORMATION A
SPECIFICATIONS
This isa "GROUNDED device The male plug
contains a ground pin and is only intended lo
use With a three-pronged grounded outlet.
This device is for use With a izoVAC power source.
izvac / son
Do not attach a device that exceeds the unit ratings:
aA/ iooow Tungsten (Maximum total load)
2.67A / 313w Tungsten (Each outlet)
#1“ i6/3 AWG SJ‘I' Vinyl Power cord
WARNING: CHOKING HAZARD - Small
Parts. Not for children under 3 years.
FCC REGULATORY STATEMENT
WARNIN hangesormodtficatipnstothisunitnot
expressly approved by the party responsible for
compliance could void the user authority to operate
the equipment.
Thls device complies With part is oi the Fcc rules
Operation is subleci to the followmg two conditrorls
l, This device may not cause harmful interference.
and
1 This deVice must accept any interference
recerved. including interference that may cause
undesrred operation.
Notes this Equlpment has been tested and found to
comply With the limits ior a Class is digital device.
pursuant to Part is of the FCC Rules. These limits
are designed to provide reasonable protection
against harmrui interference in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and. rf not installed
and used In accordance with the instructions. may
cause harmrul interference to radio
communications However. there is no guarantee
that inteirerenca wtll not occur in a partrcular
installation. it thrs equipment does cause harmrul
interference to radio or television reception. which
can be determined by turning the aaurpmeht ofl and
on. the user is encouraged to try to correct the
interference by one or more of the foliowmg
measures
i Raorient or relocate the receiving antenna
2 Increase the separation between the equipment
and receiver.
3. Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
4. Consult the dealer or an expertenced rodlo/TV
technician lor help.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : wakeyouw
Create Date                     : 2013:03:20 15:53:45+08:00
Modify Date                     : 2013:03:20 15:53:45+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Creator                         : wakeyouw
Title                           : Full page photo
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:3156e0ff-d328-42c7-a996-4f6754b95fd0
Instance ID                     : uuid:4eea4fca-edcc-453a-8fa0-838d6e76407e
Page Count                      : 1

EXIF Metadata provided by EXIF.tools