Pro Nets Technology WA41R Wireless ADSL 2+ ROUTER User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1293401
Application ID	eS96Zs6SbFYX2/Rv8i8HLA==
Document Description	user manual 4
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	110.49kB (1381150 bits)
Date Submitted	2010-06-09 00:00:00
Date Available	2010-06-10 00:00:00
Creation Date	2010-06-01 15:37:38
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2010-06-01 15:37:38
Document Title	untitled

Outbound Priority -- The priority level for the traffic that matches this classification rule. The
possible selections are (in the descending priority): p0, p1, p2, p3.
Precedence -- Select this field to mark the IP precedence bits in the packet that match this
classification rule.
TOS (Type of Service) -- Select this field to mark the IP TOS bits in the packet that match this
classification rule.
802.1p -- Select this field to mark the 3-bit user-priority field in the 802.1p header of the packet
that match this classification rule. Note that this 802.1p marking is workable on a given PVC
channel only if the VLAN tag is enabled in this PVC channel.
[QoS Quese]
This page displays the list of QoS Queue Configuration.
4.7.7 Remote Access
The Remote Access function can secure remote host access to your DSL device from LAN
and WLAN interfaces for some services provided by the DSL device.
59
LAN -- Check/un-check the services on the LAN column to allow/un-allow the services
access from LAN side; and “WAN”.
WAN -- Check/un-check the services on the WAN column to allow/un-allow the services
access from WAN side.
WAN Port -- This field allows the user to specify the port of the corresponding service. Take
the HTTP service for example; when it is changed to 8080, the HTTP server address for the
WAN side is http://dsl_addr:8080, where the dsl_addr is the WAN side IP address of the DSL
device.
4.7.8 Others
Here you can set some other advanced settings
60
IP Pass through -- The available interfaces are listed. You have to select one for advanced
configuration.
Lease Time -- The Lease Time is the amount of time that a network user is allowed to
maintain a network connection to the device using the current IP address.
Allow LAN access – Check this option to enable the LAN access
4.8 Diagnostic
The DSL device supports some useful diagnostic tools.
4.8.1 Ping
Once you have your DSL device configured, it is a good idea to make sure you can ping the
network. A ping command sends a message to the host you specify. If the host receives the
message, it sends messages in reply. To use it, you must know the IP address of the host you
are trying to communicate with and enter the IP address in the Host Address field. Click Go! To
start the ping command, the ping result will then be shown in this page
61
Host Address -- The IP address you want to ping.
4.8.2 ATM Loopback
In order to isolate the ATM interface problems, you can use ATM OAM loopback cells to verify
connectivity between VP/VC endpoints, as well as segment endpoints within the VP/VC. ATM
uses F4 and F5 cell flows as follows:
í F4: used in VPs
í F5: used in VCs
An ATM connection consists of a group of points. This OAM implementation provides
management for the following points:
í Connection endpoint: the end of a VP/VC connection where the ATM cell are
terminated
í Segment endpoint: the end of a connection segment.
This page allows you to use ATM ping, which generates F5 segment and end-to-end
loop-back cells to test the reach-ability of a segment endpoint or a connection endpoint.
62
Select PVC -- Select the PVC channel you want to do the loop-back diagnostic.
Flow Type -- The ATM OAM flow type. The selection can be F5 Segment or F5 End-to-End.
Loopback Location ID -- The loopback location ID is the field for the loop-back cell. The
default value is all Fs to indicate the endpoint of the segment or connection.
4.8.3 ADSL
This page shows the ADSL diagnostic result. Click Start button to start the ADSL diagnostic.
63
4.8.4 Diagnostic Test
The Diagnostic Test page shows the test results for the connectivity of the physical layer and
protocol layer for both LAN and WAN sides.
64
Select the Internet Connection -- The available WAN side interfaces are listed. You have to
select one for the WAN side diagnostic.
4.9 Admin
4.9.1 Commit/Reboot
Whenever you use the Web configuration to change system settings, the changes are initially
placed in temporary storage. These changes will be lost if the device is reset or turn off. To
save your change for future use, you can use the commit function
65
Commit and Reboot -- Whenever you use the web console to change system settings, the
changes are initially placed in temporary storage. To save your changes for future use, you
can use the Commit/Reboot function. This function saves your changes from RAM to flash
memory and reboot the system.
IMPORTANT! Do not turn off your modem or press the Reset button while this procedure is in
progress.
4.9.2 Backup/Restore
This page allows you to backup and restore your configuration into and from file in your host.
66
4.9.3 Password
The first time you log into the system, you use the default password. There are two-level logins:
admin and user. The admin and user password configuration allows you to change the
password for administrator and user.
67
User Name -- Selection of user levels are: admin and user.
Old Password -- Enter the old password for this selected login.
New Password -- Enter the new password here.
Confirmed Password -- Enter the new password here again to confirm.
4.9.4 Upgrade Firmware
To upgrade the firmware for the DSL device:
í Click the Browse button to select the firmware file.
í Confirm your selection.
í Click the Upload button to start upgrading.
IMPORTANT! Do not turn off your DSL device or press the Reset button while this procedure
is in progress.
68
4.9.5 ACL Configuration
The Access Control List (ACL) is a list of permissions attached to the DSL device. The list
specifies who is allowed to access this device. If ACL is enabled, all hosts cannot access this
device except for the hosts with IP address in the ACL table.
69
ACL Capability -- Enable/disable the ACL function
Enable -- Check to enable this ACL entry
Interface -- Select the interface domain: LAN or WAN
IP Address -- Enter the IP address that allows access to this device.
Subnet Mask -- Enter the Subnet Mask that allows access to this device.
4.9.6 Time Zone
Simple Network Timing Protocol (SNTP) is a protocol used to synchronize the system time
to the public SNTP servers. The DSL device supports SNTP client functionality in compliance
with IETF RFC2030. SNTP client functioning in daemon mode which issues sending client
requests to the configured SNTP server addresses periodically can configure the system clock
in the DSL device.
70
Current Time -- The current time of the specified time zone. You can set the current time by
yourself or configured by SNTP.
Time Zone -- Select time zone in which the DSL device resides.
Enable SNTP client update -- Enable the SNTP client to update the system clock.
SNTP server -- The IP address or the host name of the SNTP server. You can select from the
list or set it manually.
4.9.7 TR-069 Configuration
TR-069 is CPE Management Protocol from WAN side [CPE WAN Management Protocol
(CWMP)], intended for communication between a CPE and Auto-Configuration Server (ACS).
The CPE WAN Management Protocol defines a mechanism that encompasses secure
auto-configuration of a CPE, and also incorporates other CPE management functions into a
common framework.
71
[ACS]
URL -- URL of the auto configuration server (ACS) provided by the ISP
User Name -- Entry the User name for ACS which is provided by ISP.
Password -- Entry the password for ACS which is provided by ISP.
Periodic Inform Enable -- Enable/disables the RG to connect to the ACS periodically. If you
enable this feature, you should enter a value in the Periodic Inform Interval field.
Periodic Inform Interval -- This field is enabled only when the Periodic Inform Enabled field is
checked. It defines the amount of time (in seconds) between a successful connection with an
ACS server and a new attempt to connect to an ACS server. A recommended value is 86400
seconds (1 day).
72
[Connection Request]
User Name -- Key in the User name for ADSL router.
Password -- Key in the password for ADSL router.
Path -- The path for connection request. Default is “/tr069”.
Port -- The port for connection request. Default is “7547”.
[Debug]
ACS Certificates CPE -- The ACS URL is used by the CPE for validating the certificate from
the ACS when using certificate-based authentication.
Show Message -- Enable/Disable Show message feature.
CPE Sends GetRPC -- Enable/Disable CPE sends GetRPC function.
Skip MReboot -- Enable/Disable Skip MRboot feature.
Delay -- Enable/Disable Delay feature.
Auto-Execution -- Enable/Disable Auto-Execution feature.
CT Inform Extension -- Enable/Disable Ct Inform Execution feature.
[Certificate Management]
CPE Certificate Password -- The password is for CPE certificate.
CPE Certificate -- Browse CPE certificate which is provided by ISP server. The CPE may use
online certificate enrollment with the CA associated with the ACS. The CPE must be provided
with the information needed to contact this CA.
CA Certificate -- Browse CA certificate which is provided by ISP server.
4.10 Statistics
The DSL device shows the different layer of network statistics information
4.10.1 Interface
You can view statistics on the processing of IP packets on the networking interfaces. You will
not typically need to view this data, but you may find it helpful when working with your ISP to
diagnose network and Internet data transmission problems.
To display updated statistics showing any new data since you opened this page, click
Refresh.
73
4.10.2 ADSL
This page shows the ADSL line statistic information.
74
75

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Page Count                      : 17
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:5d4d47c8-e9b9-4361-a1cc-48beec40e05f
Producer                        : Acrobat Distiller 6.0 (Windows)
Modify Date                     : 2010:06:01 15:37:38+08:00
Create Date                     : 2010:06:01 15:37:38+08:00
Document ID                     : uuid:db251717-d882-4395-8590-7939e6de1a5f
Format                          : application/pdf
Title                           : untitled

EXIF Metadata provided by EXIF.tools