Procom Blue Flame Vent Free Mn060Hba Users Manual F

MN100HBA to the manual 06b32ddd-a328-48e4-aa02-22f88be1c829

: Procom Procom-Blue-Flame-Vent-Free-Mn060Hba-Users-Manual-520703 procom-blue-flame-vent-free-mn060hba-users-manual-520703 procom pdf

Open the PDF directly: View PDF .
Page Count: 24

Download
Open PDF In Browser	View PDF

BLUE FLAME VENT-FREE
NATURAL GAS
SPACE HEATER

OWNER ’S OPERATION AND INSTALLATION MANUAL

MN060HBA MN100HBA MN100TBA
Table of

Contents

Important Safety Information.................................2
Product Features.....................................................3
Proper Ventilation & Fresh Air...............................4
Installation................................................................6
Operating Your Heater...........................................10
Cleaning & Maintenance.......................................13
Trouble Shooting...................................................14
Specifications..........................................................17
Parts List.................................................................19

WARNI NG: If the information in this
manual is not followed exactly, a f i r e o r
e x p l o s i o n m a y r e s u l t causing property
damage, personal injury, or loss of life.
WARNING: This is an unvented gas-fired
heater. It uses air (oxygen) f r o m t h e r o o m
i n w h i c h i t i s installed. Provisions for
adequate combustion and ventilation air must
b e p r o v i d e d . R e f e r t o A i r F o r Combustion and Ventilation section on page 4 of this
manual.
CONTINENTAL APPLIANCE INC/U.S. OFFICE
5 Musick
Irvine
CA 92618

4600 Highlands Parkway S.E.
Suite # D/E

Do not store, or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
WHAT TO DO IF YOU SMELL GAS
l Do not try to light any appliance.
l Do not touch any electrical switch; do not
use any phone in your building.
l Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
l If you cannot reach your gas supplier, call
the fire department.
Installation and service must be performed by a
qualified installer, service agency or gas
supplier.

WA R N I N G : I m p r o p e r
installation,
adjustment, alteration, service or maintenance can cause injury or property damage.
Refer to this manual for correct installation and
operational procedures. For assistance or
additional information consult a qualified
installer, service agency, or gas supplier.
This appliance may be installed in an aftermarket* permanently located, manufactured
(mobile) home, where not prohibited by local
codes.
This appliance is only for use with the type of
gas indicated on the rating plate. This
appliance is not convertible for use with other
gases.
*Aftermarket: Completion of sale, not for purpose of
resale, from the manufacturer.

WATER VAPOR: A BY-PRODUCT OF UNVENTED
ROOM HEATERS
Water vapor is a by-product of gas combustion. An
unvented room heater produces approximately one
(1) ounce (30ml) of water for every 1,000 BTU’s
(.3KW’s) of gas input per hour. Refer to page 3.

Smyrna, GA 30080

Nanjing PRO-COM Electric Appliance Co.,Ltd.
#6 Chuangye Road,High New Tech.Zone,
Great Bridge Road North,Nanjing,210061,
China.

TOLL FREE NUMBER: 1-877-886-5989

Installer: Please leave these instructions with the
consumer.
Consumer: Please retain these instructions for
future use.
PR-ML062-15-0803

IMPORTANT
SAFETY INFORMATION
WARNINGS
I M P O R TA N T: R e a d t h i s
owner’s manual carefully and
completely before trying to
assemble, operate, or service
this heater. Improper use of
this heater can cause serious
injury or death from burns,
fire,
explosion,
electrical
shock, and carbon monoxide
poisoning.
WARNING: Do not use any
accessory not approved for
use with this heater.
WARNING: Any change to
this heater or its controls can
be dangerous.
Do not place clothing or other
flammable material on or near
the appliance. Never place any
objects on the heater.
Due to high temperatures, heater
should
be
kept
out
of
traffic and away from furniture
and draperies.
Surfa c e o f h e a t e r b e c o me s
very hot when running heater.
Keep children and adults away
from hot surface to avoid burns
or clothing ignition. Heater will
remain hot for a time after shut
down. Allow surface to cool
before touching.

State of Massachusetts: The
installation must be made by a licensed plumber or gas fitter in the
Commonwealth of Massachusetts.
Sellers of unvented propane or natural gas-fired supplemental room heaters shall provide to each purchaser a
copy of 527 CMR 30 upon sale of the
unit.
In the state of Massachusetts,
unvented propane or nature gas-fired
space heaters shall be prohibited in
bedrooms and bathrooms.
1. This appliance is only for use
with the type of gas indicated
on the rating plate. This
appliance is not convertible for
use with other gases.
2. If you smell gas
l Shut off gas supply.
l Do not try to light any appliance.
l Do not touch any electrical switch,
do not use any phone in your
building.
l Immediately call your gas sup
plier from a neighbor’s phone.
Follow the gas supplier’s
instructions.
l If you cannot reach your gas
supplier, call the fire department.

3.

Carefully supervise young
children when they are in the
same room with heater.
Make sure grill guard is
place before running heater.

in

Keep the appliance area clear
and free from combustible
materials, gasoline, and other
flammable vapors and liquids.
WARNING
Modeles MN060HBA, MN100HBA,
MN100TBA are equipped for natural
gas. Field conversion is not
permitted.

4.

5.

6.
l
l

This heater needs fresh,
outside air ventilation to run
properly. This heater has an
Oxygen Depletion Sensor
(ODS) safety shutoff system.
The ODS shuts down the
heater if not enough fresh air
is available. See Fresh Air For
Combustion And Ventilation
pages 4 through 6.
Keep all air openings in the front
and bottom of heater clear
and free of debris. This will
insure enough air for proper
combustion.
If heater shuts off. Do not
relight until you provide fresh
outside air. If heater keeps
shutting off, have it serviced.
Do not operate heater
where flammable liquids or
vapors are used or stored
under dusty conditions

2

7. Turn heater off before using
furniture polish, wax, carpet
cleaner, or similarproducts, If
heated, the vapors from these
products may create a white
powder residue within burner
box or on adjacent walls or
furniture.
8.

Do not use heater if any part
has been
under
water.
Immediately call a qualified
service technician to inspect
the room heater and to
replace any part of the control
system and any gas control
which has been under water.
9. Turn off heater and let cool
before servicing. Only a
qualified service person should
service and repair heater.
10. Operating
heater
above
elevations of 4,500 feet could
cause pilot outage.
11. Do not install in a bathroom
except model MN060HBA.
DANGER: Carbon monoxide
poisoning may lead to death!
Carbon Monoxide Poisoning:
Early signs of carbon monoxide
poisoning resemble the flu with
headaches, dizziness, or nausea.
If you have these signs, the heater
may not be working properly. Get
fresh air at once! Have heater
serviced. Some people are more
affected by carbon monoxide than
others. These include pregnant
women, persons with heart or lung
disease or anemia, those under the
influence of alcohol, and those
at high altitudes.
Natural Gas: Natural gas is odorless.
An odor-making agent is added to
natural gas. The odor helps you detect a natural gas leak . However,
the odor added to natural gas can
fade. Natural gas may be present
even though no odor
exists. Make
certain you read and understand all
warnings. Keep this manual for
reference. It is your guide to safe and
proper operation of this heater.

PRODUCT FEATURES

Figure1-Vent-Free Natural Gas Heater

SAFETY DEVICE

LOCAL CODES

A standard requirement for all vent-free room
heaters. This heater has a pilot with an Oxygen
Depletion Sensor(ODS) safety shutoff system.
The ODS/pilot shuts off the heater if there is
not enough fresh air.

Install and use heater with care. Follow all local
codes. In the absence of local codes, use the
latest edition of National Fuel Gas Code ANSZ223.1,
also known as NFPA 54*.
*Available from :
American National Standards Institute, Inc.
1430 Broadway
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269

PIEZO IGNITION SYSTEM
This heater is equipped with a piezo ignitor.
This system requires no matches, batteries, or
other sources to light heater.

THERMOSTATIC CONTROL
THERMOSTAT MODEL

UNPACKING

ON

1. Remove heater from carton.
2. Remove all protective packaging applied to
heater for shipment.
3. Check heater for any shipping damage. If heater
is damaged. promptly inform dealer where you
bought heater.

These heaters have a control valve with a
thermostat sensing bulb. This results in the
greatest heater comfort and may result in
lower gas bills.

WAT E R VA P O R : A B Y- P R O D U C T O F U N V E N T E D R O O M H E AT E R S
The following steps will help insure that water vapor
does not become a problem.
1. Be sure the heater is sized properly for the
application, including ample combustion air and
circulation air.
2. If high humidity is experienced, a dehumidifier
may be used to help lower the water vapor content of the air.
3. Do not use an unvented room heater as the primary heat source.

Water vapor is a by-product of gas combustion. An
unvented room heater produces approximately one
(1) ounce (30ml) of water for every 1,000 BTU’s
(.3KW’s) of gas input per hour.
Unvented room heaters are recommended as supplemental heat (a room) rather than a primary heat
source (an entire house). In most supplemental heat
applications, the water vapor does not create a
problem. In most applications, the water vapor enhances the low humidity atmosphere experienced
during cold weather.
3

FRESH AIR FOR
COMBUSTION AND
VENTILATION
WARNING: This heater
shall not be installed in a
confined space or unusually
tight
co n s tr u cti o n
u n l es s
provisions are provided for
adequate
combustion
and
ventilation air. Read the
following instructions to
insure proper fresh air for this
and
other
fuel-burning
appliances in your home.

PROVIDING ADEQUATE
VENTILATION
The following are excerpts from
National Fuel Gas Code. NFPA
54/ANS Z223.1, Section 5.3. Air for
Combustion and Ventilation. All
spaces in homes fall into one of
the three following ventilation
classifications:
1. Unusually Tight Construction
2. Unconfined Space
3. Confined Space
The information on pages 4
through 6 will help you classify
your space and provide adequate
ventilation.

Unusually Tight Construction
The air that leaks around doors and
windows may provide enough fresh
air for combustion and ventilation.
However, in buildings of unusually
tight construction. you must provide
additional fresh air.
Unusually tight construction is
defined as construction where:
a. walls and ceilings exposed to the
outside
atmosphere
have
a
continuous water vapor retarder
with a rating of one perm (6×10-11 kg
per pa-sec-m 2 )
or less with
openings gasketed or sealed and
b. weather stripping has been
added on openable windows and
doors and
c. caulking or sealants are applied to
areas such as joints around
window and door frames, between
sole plates and floors, between
wall-ceiling joints, between wall
panels, at penetrations for plumbing,
electrical, and gas lines, and at
other openings. If your home meets
all of the three criteria above, you
must provide additional fresh air.
See Ventilation Air From Outdoors,
page 6.
If your home does not meet all of
the three criteria above see
Determining Fresh-Air Flow for
Heater Location, page 5.

Confined and
Unconfined Space
The National Fuel Gas Code ANS
Z223.1 defines a confined space as
a space whose volume is less than
50 cubic feet per 1,000 Btu per hour
(4.8 m3 per kw)
of
the
aggregate input rating of all
appliances installed in that space
and an unconfined space as a
space whose volume is not less
than 50 cubic feet per 1,000 Btu per
h o u r ( 4 .8 m 3 p e r k w ) o f th e
aggregate input rating of all
appliances installed in that space.
Rooms communicating directly with
the space in which the
appliances are installed*, through
openings not furnished with doors,
are considered a part of the
unconfined space.
This heater shall not be installed
in a confined space or unusually
tight
construction
unless
provisions are provided for
adequate
combustion
and
ventilation air.
* Adjoining rooms are
communicating only if there are
doorless
passageways
or
ventilation grills between them.

DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION
Determining if you have a Confined or Unconfined Space*
Use this worksheet to determine if you have a confined or unconfined space.
Space: Includes the room in which you will install heater plus any adjoining rooms with doorless passageways
or ventilation grills between the rooms.
1. Determine the volume of the space (length×width×height).
cu.ft. (volume of space)
Length×Width×Height=
Example: Space size 18ft. (length)×16ft.( width)×8ft. (ceiling height)=2304cu. ft. (volume of space)
If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these
rooms to the total volume of the space.
2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.
(volume of space)÷50 cu. ft.=(Maximum Btu/Hr the space can support)
Example: 2304 cu. ft. (volume of space)÷50 cu.ft.=46.1 or 46.100(maximum Btu/Hr the space can support)
WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined
space or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one
of the methods described in the National Fuel Gas Code, ANS Z223.1, Section 5.3
or applicable local codes.

4

3. Add the Btu/Hr of all fuel burning appliances in the space.
Vent-free heater
Btu/Hr
Example:
Gas water heater*
Btu/Hr
Gas water heater
44,000
Btu/Hr
Gas furnace
Btu/Hr
Vent free heater +
10,000
Btu/Hr
Vented gas heater
Btu/Hr
Total
= 54,000
Btu/Hr
Gas Fireplace logs
Btu/Hr
Other gas appliances* +
Btu/Hr
Total
=
Btu/Hr
*Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and
vents to the outdoors.
4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.
Btu/Hr (maximum the space can support)
Btu/Hr (actual amount of Btu/Hr used)
Example : 51,200 Btu/Hr(maximum the space can support)
54,000 Btu/Hr(actual amount of Btu/Hr used)
The space in the above example is a confined space because the actual Btu/Hr used is more than the
maximum Btu/Hr the space can support.
You must provide additional fresh are. Your options are as follows:
A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined
space, remove door to adjoining room or add ventilation grills between rooms. See Ventilation Air From
inside Building, page 5.
B. Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 6 .
C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.
If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an
unconfined space. You will need no additional fresh air ventilation.
AIR FOR COMBUSTION AND
VENTILATION
Continued
VENTILATION AIR
Ventilation Air From Inside Building
This fresh air would come from an adjoining
unconfined space. When ventilating to an
adjoining unconfined space, you must
provide two permanent openings: one within
12" of the ceiling and one within 12" of the
floor on the wall connecting the two spaces
(see options 1 and 2, Figure 2). You can also
remove door into adjoining room (see option
3, Figure 2). Follow the National Fuel Gas
Code NFPA 54/ANS Z223.1. Section 5.3, Air
for Combustion and Ventilation for required
size of ventilation grills or ducts
WARNING: Rework worksheet, adding the space of the adjoining
unconfined space. The combined spaces
must have enough fresh air to supply all
appliances in both spaces.
Figure 2 -Ventilation Air from Inside Building

5

VENTILATION AIR
Ventilation Air From Outdoors
Provide extra fresh air by using
ventilation grills or duels: You must
provide two permanent openings: one within
12 " of the ceiling and one within
12" of the floor.
Connect these items directly to the
outdoors or spaces open to the outdoors.
These spaces include attics and crawl
spaces. Follow the National Fuel Gas
Code NFPA 54/ANS Z223.1, Section 5.3.
Air for Combustion and Ventilation for
required size of ventilation grills or ducts.
IMPORTANT: Do not provide openings for
inlet or outlet air into attic if attic has a
thermostat-controlled power vent.
Heated air entering the attic will activate
the power vent.

Figure 3 -Ventilation Air from Outdoors

INSTALLATION
NOTICE: This heater is
intended for use as supplemental
heat. Use this heater along with
your primary heating system. Do
not install this heater as your
primary heat source. If you have
a central heating system, you
may run system’s circulating
blower while using heater. This
will help circulate the heat
throughout the house. In the
event of a power outage, you can
use this heater as your primary
heat source.
WARNING: A qualified
service person must install
heater. Follow all local codes.
CHECK GAS TYPE
Use only natural gas. If your
gas supply is not natural, do not
install heater. Call dealer where you
bought heater for proper type heater.

INSTALLATION NEEDS
Before installing heater, make sure
you have the items listed below:
l piping (check local codes)
l sealant (resistant to natural gas)
l equipment shutoff valve*
l ground joint union
l test gauge connection*
l sediment trap
l tee joint
l pipe wrench
*A CSA/AGA design-certified equipment shutoff valve with 1/8" NPT
tap is an acceptable alternative to
test gauge connection. Purchase
the optional CSA/AGA design certified equipment shutoff valve from
your dealer. See Accessories, page
17.

LOCATING HEATER
This heater is designed to be
mounted
on
a
wall.
For convenience and efficiency,
install heater
l where there is easy access for
operation, inspection, and service

l

in coldest part of room

CAUTION: If you install the
heater in a home garage
l heater pilot and burner must
be at least 18 inches above
floor.
l locate heater where moving
vehicle will not hit it.
6

WARNING: Never install
the heater
l
in a bathroom (Models
MN100HBA and MN100TBA, only
MN060HBA is allowed in bathroom.
Check local codes.)
l in a recreational vehicle.
l
where curtains, furniture,
clothing, or other flammable objects are less than 36 inches
from the front, top, or sides of the
heater.
l as a fireplace insert.
l in high traffic areas.
l in windy or drafty areas.
When the heater is installed in
Bathrooms,do not use flammable
products such as aerosol hair spray,
foot spary or any product that contains
flammable vapors and keep towels
away from heater.(only MN060HBA is
allowed in a bathroom.)
CAUTION: This heater creates warm air currents.These currents move heat to wall surfaces
next to heater. Installing heater
next to vinyl or cloth wall coverings or operating heater where
impurities (such as tobacco
smoke, aromatic candles, cleaning fluids, oil or kerosene lamps,
etc.) in the air exist may discolor
walls.

INSTALLATION
WARNING: Maintain the
minimum clearances shown
in Figure 4. If you can,
provide greater clearances from
floor, ceiling, and joining wall.

FASTENING HEATER TO WALL
Mounting Bracket
The mounting bracket is located
on back panel of heater (see
Figure 6). It has been taped there
for shipping. Remove mounting
bracket from back panel.

Figure 6 -Mounting Bracket
Location

Figure 4 -Mounting clearances As
View From Front of Heater
INSTALLING THERMOSTAT
SENSING BULB
For T-Stat Model Only
1. Pull out the sensing bulb from the
two clips located in the shippng
position according to the direction
as shown by the arrow. There is no
need to take out the two bulb clips.
2. Take out the bulb clip from the
hardware package and insert it into
the square hole and then insert the
sensing bulb into the bulb clip (see
Figure 5).

Figure 5 -Moving Thermostat
Sensing Bulb

Removing Lower Front Panel Of
Heater
1. Remove two Screws near
bottom corners of lower front
panel.
2. Pull bottom of lower front panel
forward, then down (see Figure
7).

Attaching to Wall Anchor: This
method allows you to attach
mounting bracket to hollow walls (wall
areas between studs) or to
solid walls (concrete or masonry).
Decide which method better
suits
your needs. Either method
will
provide a secure hold for the
mounting bracket.
Marking Screw Locations
1. Tape mounting bracket to wall
where heater will be located.
Make sure mounting bracket is
level.
WARNING:
Maintain
minimum clearances shown in
Figure 8. If you can, provide
greater clearances from floor
and joining wall.
2. Mark screw locations on
wall. (see Figure 8)
Note: Only mark last hole on
each end of mounting bracket.
Insert mounting screws through
these holes only.
3. Remove tape and mounting
bracket from wall.

Figure 7 - Removing Lower Front
Panel Of Heater
Methods For Attaching Mounting
Bracket To Wall
Only use last hole on each end of
mounting bracket to attach bracket
to wall. Attach mounting bracket to
wall only in one of two ways:
1. Attaching to wall stud
2. Attaching to wall anchor
Attaching to Wall Stud: This method
provides the strongest hold. Insert
mounting screws through mounting
bracket and into wall studs.

7

Figure 8 - Mounting Bracket
Clearances

INSTALLATION
Attaching Mounting Bracket To
Wall
Note: Wall anchors, mounting
screws, and spacers are in
hardware package. The hardware
package is provided with heater.
Attaching to Wall Stud Method
For attaching mounting bracket to
wall studs
1. Drill holes at marked locations
using 9/64" drill bit.
2. Place mounting bracket onto
wall. Line up last hole on each
end of bracket with holes drilled
in wall.
3. Insert mounting screws through
bracket and into wall studs.
4. Tighten screws until mounting
bracket is firmly fastened to
wall studs.
Attaching to Wall Anchor Method
For attaching mounting bracket to
hollow walls (wall areas between
studs) or solid walls (concrete or
masonry)
1. Drill holes at marked locations
using 5/16" drill bit. For solid
walls (concrete or masonry),
drill at least 1" deep.
2. Fold wall anchor as shown in
Figure 9 below.

IMPORTANT: Do not
hammer
key! For thick walls
(over 1/2" thick) or solid walls,
do not pop open wings.

Figure 10 - Popping Open Anchor
Wing For Thin Walls
5. Place mounting bracket onto
wall. Line up last hole on
each end of bracket with wall
anchors.
6. Insert mounting screws through
bracket and into wall anchors.
7. Tighten screws until mounting
bracket is firmly fastened to
wall.
Placing Heater On Mounting
Bracket
1. Locate two horizontal slots on
back panel of heater (see
Figure 11).
2. Place heater onto mounting
bracket. Slide horizontal slots
onto stand-out
tabs
on
mounting bracket.

Figure 9 - Folding Anchor
3.

4.

Insert wall anchor (wings
first) into hole. Tap anchor
flush to wall.
For thin walls (1/2" or less),
insert red key into wall
anchor. Push red key to
"pop" open anchor wings.
(see Figure 10)

Installing Bottom Mounting
Screw
1. Locate bottom mounting
hole. This hole is near bottom
on back
panel of heater
(see Figure 12).

Figure 11 - Mounting Heater Onto
Mounting Mracket

8

Figure 12 - Installing Bottom
Mounting Screw
2. Mark screw locations on wall.
3. Remove
heater
from
mounting bracket.
4. If installing bottom mounting
screw into hollow or solid wall,
install wall anchors. Follow steps
1 through 4 under Attaching To
Wall Anchor Method. If installing
bottom mounting screw into wall
stud, drill
hole at marked
locations using 9/64" drill bit.
5. Replace heater onto mounting
bracket.
6. Place spacer between bottom
mounting holes and wallanchor
or drilled hole.
7. Hold spacer in place with one
hand. With other hand, insert
mounting screw through bottom
mounting hole and spacer. Place
tip of screw in opening of wall
anchor or drilled hole.
8. Tighten screw until heater is firmly
secured to wall. Do not over tighten.
l Note: Do not replace lower front
panel at this time. Replace lower
front panel after making gas
connections and checking for
leaks (see page 9).

INSTALLATION
CONNECTING TO GAS SUPPLY
WARNING: A qualified
service person must connect
heater gas supply. Follow all
local codes.
WARNING: This appliance
requires a 3/8" NPT (National Pipe
Thread) inlet connection
to the pressure regulator.
WARNING: Never connect
heater to private (non-utility) gas
well. This gas is commonly
known as well-head gas.
IMPORTANT: Check your gas line
pressure before connecting heater to
gas line. Gas line pressure must be
no greater than 10.5 inches of water.
If gas line pressure is higher, heater
regulator damage could occur.

CAUTION: Use only new,
black iron or steel pipe.
Internally-tinned copper tubing
may be used in certain areas.
Check your local codes. Use pipe
of large enough diameter to
allow proper gas volume to heater.
If
pipe
is
too
small,
undue loss of pressure will
occur.
Typical Inlet Pipe Diameters
All models up to 20,000 BTU’s use
3/8’’ or greater pipe;
All models 25,000 BTU’s and higher,
use 1/2” or greater pipe.
Installation must include an
equipment shutoff valve, union, and
plugged 1/8" NPT tap. Locate NPT
tap within reach for test gauge hook
up. NPT tap must be up stream from
heater (see Figure 13).

Figure 13 -Gas Connection
*A CSA/AGA design-certified equipment shutoff valve with 1/8" NPT tap is
an acceptable alternative to test gauge connection. Purchase the optional
C S A / A G A d e s i g n - c e r t i f i e d e q u i p m e n t s h u t o ff v a l v e f r o m
your dealer. See Accessories, page 17.
IMPORTANT: Install an equipment
shutoff valve in an accessible
location. The equipment shutoff
valve is for turning on or shutting
off the gas to the appliance.
Apply pipe joint sealant lightly to
male threads. This will prevent
excess sealant from going into
pipe. Excess sealant in pipe could
result in clogged heater valves.
CAUTION: Use pipe joint
sealant that is resistant to
natural gas.

9

Install sediment trap in supply line
as shown in Figure 13. Locate
sediment trap where it is within
reach
for c l e a n i n g . L o c a te
sediment
trap where trapped
matter is not likely to freeze. A
sediment trap traps moisture and
contaminants. This keeps them
from going into heater controls. If
sediment trap is not installed or is
installed wrong, heater may
not run properly.
IMPORTANT:
Hold pressure
regu lator with w rench when
connecting it to gas piping and/or
fittings.

INSTALLATION
CHECKING GAS
CONNECTIONS
WARNING: Test all gas
piping and connections for leaks after
installing or servicing. Correct all
leaks at once.
WARNING: Never use an open
flame to check for a leak. Apply a
mixture of liquid soap and water
to all joints. Bubbles forming
show a leak. Correct all leaks at
once.

Pressure Testing Gas Supply
Piping System
Test Pressures In Excess Of
1/2 PSIG (3.5 K Pa)
1. Disconnect appliance with its
appliance
main
gas valve
(control valve) and equipment
shutoff valve from gas supply
piping system. Pressures in
excess of 1/2 psig will damage
heater regulator.
2. Cap off open end of gas pipe
where equipment shutoff valve
was connected.
3. Pressurize
supply
piping
system by either using
compressed air or opening
main gas valve located on or
near gas meter.
4. Check all joints of gas supply
piping system. Apply mixture of
liquid soap and water to gas
joints. Bubbles forming show
a leak.
5. Correct all leaks at once.
6. Reconnect heater and equipment
shutoff valve to gas supply. Check
reconnected fittings for leaks.

OPERATING YOUR HEATER

Pressure Testing Heater Gas
Connections
1. Open equipment shutoff valve
(see Figure 14).
2. Open main gas valve located on
or near gas meter.
3. Make sure control knob of
heater is in the OFF position.
4. Check all joints from equipment
shutoff valve to control valve
(see Figure 15 ). Apply mixture of
liquid soap and water to gas
joints. Bubbles forming show
a leak.
5. Correct all leaks at once.
6. Light heater (see Operating
Heater, pages 10 and 11 for
non-thermostat models or page
12 for thermostat model).Check
the rest of the internal joints for
leaks.
7. Turn off heater (see To Turn Off
Gas to Appliance, page 11 for
non-thermostat models or page
12 for thermostat model).
8. Replace lower front panel.

Figure 14 -Equipment Shutoff Valve

Test Pressures Equal To or
Less Than 1/2 PSIG (3.5 K Pa)
1.

Close equipment shutoff valve
(see Figure 14).
2. Pressurize supply piping system
by either using compressed air
or opening main gas valve
located on or near gas meter.
3. Check all joints from gas meter to
equipment shutoff valve (see
Figure 15).Apply mixture of liquid
soap and water to gas joints.
Bubbles forming show a leak.
4. Correct all leaks at once.

Figure 15 -Checking Gas Joints
WARING:Do not over tighten gas
connections.

1 0

NON-THERMOSTAT MODEL

nFOR YOUR SAFETYn
READ BEFORE LIGHTING
WARNING: If you do not
fo llo w
these
in str uctio ns
exactly, a fire or explosion may
result
causing
property
damage, personal injury or
loss of life.
A. When lighting the pilot, follow ,
these instructions exactly.
B. BEFORE LIGHTING smell all
around the appliance area for
gas. Be sure to smell next to
the floor because some gas is
heavier than air and will settle
on the floor .
WHAT TO DO IF YOU SMELL GAS
l Do not try to light any appliance.
l Do not touch any electric switch;
do not use any phone in your
building.
l Immediately
call
your gas
supplier from a neighbor’s
phone. Follow
the
gas
supplier’s instructions.
l If you cannot reach your
gas supplier, call the fire
department.
C. Use only your hand to push in
or turn the gas control knob.
Never use tools. If the knob
will not push in or turn by
hand, don’t try to repair it, call
a qualified service technician or
gas supplier. Force or attempted
repair may result in a fire or
explosion.
D. Do not use this appliance if any
p ar t h a s b ee n u n d e r wa t e r .
Immediately call a qualified
service technician to inspect
the appliance and to replace
any part of the control system
and any gas control which has
been under water.

OPERATING
Manual Control Models
nLIGHTINGn
INSTRUCTIONS
1.

2.
3.

4.

5.

STOP! Read
the safety
information on the side of
heater.
Check that gas supply to
heater is on.
Push in gas control knob
slightly and turn clockwise
to
the OFF position.
Wait five (5) minutes to clear
out any air. Then smell for
gas, including near the floor.
If
you
smell gas, STOP!
Follow “B”
in
the
safety
information on the side of the
heater. If you do not smell
gas, go to the next step.
Push
in gas control knob
slightly
and
turn
counterclockwise
to
“PILOT/IGN” and depress for
five(5) seconds

NOTE: The first time that the
heater
is operated after
connecting the gas supply , the
control knob should be depressed
for about thirty (30) seconds. This
will allow air to bleed from the gas
system.
6. With control knob pressed in,
push down and release the
ignitor button. This will light
pilot. If needed, keep pressing
ignitor button until pilot lights.
7. Keep control knob depressed
for ten (10) seconds after
lighting pilot. If pilot goes out,
repeat steps 5,6 and 7.
8. To select the desired heating
level, partially press down the
control knob slightly and rotate
counterclockwise
. Release the
downward pressure on the knob
while continuing to turn until the
knob locks at the desired setting
position. Do not operate
between locked positions.

l

YOUR

HEATER

Set control knob to desired
heating position.
NOTE: Both HIGH and LOW
are locked positions. You
must press in control knob
before turning it from these
positions.

nTO TURN OFFn
GAS TO APPLIANCE
Shutting Off Heater
1. Turn control knob clockwise
to the OFF position.
2. Turn off all electric power to
the appliance if service is to
be performed.
Shutting Off Burner Only
(Pilot Stays Lit)
Turn control knob clockwise
to the PILOT/IGN position.

Figure 16 -1- Control Knob In
The OFF Position (MN060HBA)

nMANUAL LIGHTINGn
PROCEDURE
1.
2.
3.

4.
Figure 16-2 - Control Knob in The
OFF Position
(MN100HBA&MN100TBA)
5.

Figure 17 - Pilot

CAUTION: Do not try to
adjust heating levels by using
the equipment shutoff valve.

1 1

Remove lower front panel(see
Figure 7 page 7).
Follow steps 1 through 5
under Lighting Instructions.
With control knob pressed in,
strike match. Hold match to
pilot until pilot lights.
Keep control knob pressed in
for 30 seconds after lighting
pilot. After 30 seconds, release
control knob. Follow step 8
under Lighting Instructions.
Replace lower front panel.

OPERATING
THERMOSTAT MODEL

nFOR YOUR SAFETYn
READ BEFORE LIGHTING
WARNING: If you do not follow
these instructions exactly, a fire or
explosion may result causing
property damage, personal injury
or loss of life.

A.
When lighting the pilot, follow
these instructions exactly.
B.
BEFORE LIGHTING smell all
around the appliance area for gas.
Be sure to smell next to the floor
because some gas is heavier than
air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
l Do not try to light any appliance.
l
Do not touch any electric
switch, do not use any phone
in your building.
l
Immediately call your gas
supplier from a neighbor’s
phone. Follow the gas
supplier’s instructions.
l If you cannot reach your gas
supplier, call the fire department.
C.
Use only your hand to push
in or turn the gas control knob.
Never use tools. If the knob will
not push in or turn by hand, don’t
try to repair it , call a qualified
service technician or gas supplier.
Force or attempted repair may
result in a fire or explosion.
D. Do not use this appliance if
any part has been under water.
Immediately call a qualified service
technician to inspect the appliance
and to replace any part of the control
system and any gas control which
has been under water.

nLIGHTINGn
INSTRUCTIONS
1.
2.
3.

STOP!
Read
the
safety
information on the side of heater.
Make sure equipment shutoff
valve is fully open.
Turn control knob clockwise
to the OFF position.

YOUR

4.

HEATER

Wait five(5) minutes to clear
out any gas. Then smell for gas,
including near the floor. If you
smell gas, STOP! Follow “B” in the
safety information on the side of
heater. If you don’t smell
gas, go to the next step.
5. Turn control knob counterclockwise
to the PILOT position.
Press in control knob for five(5)
seconds. (see Figure18).
Note: You may be running
this heater for the first time
after hooking up to gas supply.
If so, the control knob may
need to be pressed in for 30
seconds. This will allow air to
bleed from the gas system.
l If control knob does not pop
up when released, contact a
qualified service person or
gas supplier for repairs.
6. With control knob pressed in,
push down and release ignitor
button. This will light pilot. The
pilot is attached to the front of
burner. The pilot can be seen
through the glass panel. If
needed, keep pressing ignitor
button until pilot lights.
Note: If pilot does not stay lit, refer
to Troubleshooting, pages 14 through
16. Also contact a qualified service
person or gas supplier for repairs.
Until repairs are made, light pilot with
match.To light pilot with match, see
Manual Lighting Procedure.
7.
Keep control
knob pressed
in for 30 seconds after lighting
pilot. After 30 seconds, release
control knob.
l If control knob does not pop
up when released, contact a qualified service person or gas
supplier for repairs.
Note: If pilot goes out,repeat steps 3
through 7.This heater has a safety
interlock system. Wait one(1)
minute before lighting pilot again.
8. Turn control knob counterclockwise
to desired heating
level. The main burner should
light. Set control knob to any
heat level between HI and LO.

1 2

CAUTION: Do not try to adjust heating levels by using the
equipment shutoff valve.

Figure 18 - Control Knob in The
OFF Position

Figure 19 - Pilot
nTHERMOSTAT CONTROL OPERATIONn

The thermostatic control used on this
model differs from standard
thermostats.Standard thermostats
simply turn on and off the burner. The
thermostat used on this heater senses
the room temperature. At times the
room may exceed the set temperature.
If so,the burner will shut off. The burner
will cycle back on when room temperature drops below the set temperature.
The control knob can be set to any comfort level between HI and LO.
Note: The thermostat sensing bulb measures the temperature of air near the
heater cabinet.This may not always agree
with room temperature(depending on
housing construction, installation location,
room size, open air temperatures,etc.)
Frequent use of your heater will let you
determine your own comfort levels.

nTO TURN OFF GASn
TO APPLIANCE
Shutting Off Heater
1. Turn control knob clockwise
to the OFF position.
2. Turn off all electric power to the
appliance if service is to
be performed.
Shutting Off Burner Only (pilot
stays lit )
Turn control knob clockwise
to
the PILOT position.

OPERATING HEATER
Continued

nMANUAL LIGHTINGn
PROCEDURE
1.
2.
3.

4.

5.

Remove lower front panel (see
Figure 7 page 7).
Follow steps through 5 under
Lighting Instructions on page12.
With control knob pressed in,
strike match. Hold match to pilot
until pilot lights.
Keep control knob pressed in for
30 seconds after lighting pilot. After
30 seconds, release control knob.
Follow step 8 under Lighting
Instuctions on page 12.
Replace lower front panel.

nINSPECTING BURNERn
Check pilot flame pattern and
burner flame pattern often.
PILOT FLAME PATTERN
Figure 20 shows a correct pilot
flame pattern. Figure 21 shows an
incorrect pilot flame pattern. The
incorrect pilot flame is not touching
thermocouple. This will cause the
thermocouple to cool. When the
thermocouple cools, the heater will
shut down. If pilot flame pattern is
incorrect, as shown in Figure 21.
l turn heater off (see To Turn
Off
Gas to Appliance on page 11
for non-thermostat models or
page 12 for thermostat models.)
l see Troubleshooting. pages 14
through 16.

BURNER FLAME PATTERN
Figure 22 shows a correct burner
flame pattern. Figure 23 shows an
incorrect burner flame pattern. If
pilot flame pattern is incorrect, as
shown in Figure 23.
WARNING: If yellow tipping
occurs, your heater could produce
increased levels of carbon
monoxide. If burner flame pattern
shows yellow tipping, follow instructions at bottom of this page.
Notice: Do not mistake orange
flames with yellow tipping. Dirt or
other fine particles enter the heater
and burn causing brief
patches of orange flame.
l

l

turn heater off (see To Turn Off
Gas to Appliance pages10 & 11
for non-thermostat models and
page 12 for thermostat models)
see Troubleshooting. pages 14
through 16

Figure 22 - Correct Burner Flame
Pattern

Figure 23 - Incorrect Burner
Flame Pattern

ODS/PILOT AND BURNER
l Use a vacuum cleaner, pressurized air or a small, soft
bristled brush to clean.
CLEANING BURNER
PILOT AIR INLET HOLE
We recommend that you clean the
unit every 2,500 hours of operation or
every three months. We also
recommend that you keep the burner
tube and pilot assembly clean and free
of dust and dirt. To clean these parts
we recommend using compressed
air no greater than 30 PSl. Your local
computer store, hardware store, or
home center may carry compressed
air in a can. You can use a vacuum
cleaner in the blow position. If using
compressed air in a can, please follow
the directions on the can. If you don’t
follow directions on the can, you could
damage the pilot assembly.
1.
Shut off the unit, including the
pilot. Allow the unit to cool for
at least thirty minutes.
2. Inspect burner and pilot for dust
and dirt.
3.
Blow air through the ports/slots
and holes in the burner.
Also clean the pilot assembly. A
yellow tip on the pilot flame indicates dust and dirt in the pilot
assembly. There is a small pilot air
inlet hole about two inches from
where the pilot flame comes out of
the pilot assembly (see Figure 24).
With the unit off , lightly blow air through
the air inlet hole. You may blow through
a drinking straw if
compressed air is
not available.

CLEANING AND
MAINTENANCE
Figure 20 - Correct Pilot Flame
Pattern

Figure 21 - Incorrect Pilot Flame
Pattern

WARNING: Turn off heater
and let cool before servicing.

Figure 24 - Pilot Inlet Air Hole

CAUTION: You must keep control areas, burner, and circulating
air passageways of heater clean.
Inspect these areas of heater
before each use. Have heater
inspected yearly by a qualified
service person. Heater may need
more frequent cleaning due to
excessive lint from carpeting,
bedding material, pet hair, etc.

CABINET
Air Passageways
l Use a vacuum cleaner or
pressurized air to clean.
Exterior
l Use a soft cloth dampened with
a mild soap and water mixture.
Wipe the cabinet to remove dust.

1 3

TROUBLESHOOTING
Note :
All
troubleshooting
items are listed in order of
operation.

WARNING: Only a qualified
service person should service and
repair heater.

CAUTION: Never use a wire,
needle, or similar object to clean
ODS/pilot. This can damage
ODS/pilot unit.

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

When ignitor button is pressed in,
there is no spark at ODS/pilot.

1. Ignitor electrode is positioned
wrong.
2. Ignitor electrode is broken.
3. Ignitor electrode is not connected
to ignitor cable.
4. Ignitor cable is pinched or wet.

5. Broken ignitor cable.
6. Bad piezo ignitor.
When ignitor button is pressed in,
there is a spark at ODS/pilot but no
ignition.

1.Gas supply turned off or
equipment shutoff valve is closed.
2. Control knob not fully pressed in
while pressing ignitor button.
3. Air in gas lines when installed.

4.

ODS/pilot is clogged.

5. Gas regulator setting is not correct
6. Control knob not in PILOT position.

ODS/pilot lights but flame goes out
when control knob is released.

1. Replace ignitor.
2. Replace ignitor.
3. Reconnect ignitor cable.
4. Free ignitor cable if pinched by
any
metal or tubing. Keep
ignitor cable dry.
5. Replace ignitor cable.
6. Replace piezo ignitor.
1. Turn on gas supply or open
equipment shutoff valve.
2. Fully press in control knob
while pressing ignitor button.
3. Continue holding down control
knob. Repeat igniting operation
until air is removed.
4. Clean ODS/pilot (see Cleaning
and Maintenance Page 13) or
replace ODS/pilot assembly.
5. Replace gas regulator.
6. Turn control knob
position.

to

PILOT

1. Control knob is not fully pressed
in.
2. Control knob is not pressed in
long enough.
3. Equipment shutoff valve is not
fully open.
4. Thermocouple connection is
loose at control valve.

1. Press in control knob fully.

5. Thermocouple damaged.
6. Control valve damaged.

5. Replace thermocouple.
6. Contact Dealer or PRO-COM.

1 4

2. After ODS/pilot lights, keep control
knob pressed in 30 seconds.
3. Fully open equipment shutoff valve.
4. Hand tighten until snug, then
tighten 1/4 turn more.

TROUBLESHOOTING
Continued

POSSIBLE CAUSE

OBSERVED PROBLEM
Burner(s ) d o e s n o t l i g h t a f t e r
ODS/pilot is lit.

REMEDY

1. Burner orifice is clogged.

2. Burner orifice diameter is too small.
3. Inlet gas pressure is too low.
Delayed ignition of burner(s).

1. Manifold pressure is too low.
2. Burner orifice is clogged.

Burner backfiring during combustion.

1. Burner orifice
damaged.

is clogged

1. Contact local natural gas company.
2. Clean burner (see Cleaning and
Maintenance Page 13) or replace
burner orifice.
or

2. Burner is damaged.
3. Gas regulator is defective.
1. Not enough air.

Yellow flame during burner
combustion.

2. Gas regulator is defective.
3. Inlet gas pressure is too low .

Slight smoke or
initial operation.

odor

during

Heater produces a whistling noise
when burner is lit.

1. Clean burner orifice (see Cleaning
and Maintenance Page 13) or
replace burner orifice.
2. Replace burner orifice.
3. Contact local natural gas company.

1. Residues from manufacturing
processes
.
1. Turning control knob to HI position
when burner is cold.
2. Air in gas line.

3. Air passageways on heater
blocked.
4. Dirty or partially clogged burner
orifice.

1. Clean burner orifice (see Cleaning
and Maintenance Page 13) or
replace.
2. Contact Dealer or PRO-COM.
3. Replace gas regulator.
1. Check burner for dirt and debris.
If found, clean burner(see Cleaning
And Maintenance Page 13).
2. Replace gas regulator.
3. Contact local natural gas company.

1. Problem will stop after a few hours
of operation.
1. Turn control knob to LO position
and let warm up for a minute.
2. Operate burner until air is removed
from line. Have gas line checked
by local natural gas company.
3. Observe
minimum installation
clearances (see Figure 4, Page 7).
4. Clean burner (see Cleaning and
Maintenance Page 13) or replace
burner orifice.

Heater produces a clicking/ticking
noise just after burner is lit or
shut off.

1. Metal is expanding while heating
or contracting while cooling.

1. This is common with most
heaters. if noise is excessive,
contact qualified service person.

White powder residue forming within
burner box or on adjacent
walls or furniture.

1. When heated the vapors from
furniture polish, wax, carpet
cleaners, etc. turn into white
powder residue.

1. Turn heater off when using
furniture polish, wax, carpet
cleaner or similar products.

1 5

TROUBLESHOOTING
Continued
WARNING: If you smell gas
l
l
l
l
l

Shut off gas supply.
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbor’s phone. Follow the gas
supplier’s instructions.
If you cannot reach your gas supplier, call the fire department.

IMPORTANT: Operating beater where impurities in air exist may create odors. Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or
textiles, etc., create fumes. These fumes may mix with combustion air and create odors.

Heater produces unwanted odors.

Heater shuts off in use (ODS operates).

1. Heater is burning vapors from
paint, hair spray, glues, etc.
(See IMPORTANT statement
above).
2 . G a s l e a k . S e e Wa r n i n g
Statement at top of page.

1.

Ventilate room. Stop using odor
causing products while heater
is running.

2.

Locate and correct all leaks(see
Checking Gas Connections,
page 10).

1.

Not enough fresh air is available.

1.

2.

Low line pressure.

3. ODS/pilot is partially clogged.

Gas odor exists even when control
knob is in OFF position.

Gas odor during combustion.

Moisture/condensation
windows.

noticed

REMEDY

POSSIBLE CAUSE

OBSERVED PROBLEM

on

Open window and/or door for
ventilation.
2. Contact local natural gas
company.
3. Clean ODS/pilot (see Cleaning
page 12).

2. Control valve is defective.

Locate and correct all leaks(see
Checking Gas Connections,
page 10).
2. Replace control valve.

1.

Foreign matter between control
valve and burner.
2. Gas
leak.
See Warning
Statement at top of page.

1.

1.

1.

1. Gas leak. See Warning
Statement at top of page.

Not enough combustion/ventilation
air.

1 6

1.

Take apart gas tubing and
remove foreign matter.
2. Locate and correct all leaks
(see Checking Gas Connections,
page 10).

Refer to Air for Combustion and
Ventilation requirements, page
4.

SPECIFICATIONS
MN060HBA
MN100HBA
Btu(available)
6,000
6,000/10,000
Gas Type
Natural Only
Natural Only
Ignition
Piezo
Piezo
Pressure Regulator setting
3"W.C
3"W.C
Inlet Gas Pressure* (inches of water)
Maximum
10.5"
10.5"
Minimum
4"
4"
Dimensions, Inches (HxWxD)
Heater
19-1/8×14-1/8×6-3/8 19-1/8×14-1/8×6-3/8
Carton
22×16-3/4×8-1/8
22×16-3/4×8-1/8
Weight (pounds)
Heater
12
13
Shipping
15
16

MN100TBA
10,000
Natural Only
Piezo
3"W.C
10.5"
4"
19-1/8×14-1/8×6-3/8
22×16-3/4×8-1/8
14
17

Note: Dimensions listed are outer most points on the heater (includes control knobs and grill).
* For purposes of input adjustment.

TECHNICAL SERVICE

REPLACEMENT PARTS

You may have further questions
about installation, operation, or
troubleshooting. If so, contact
PRO-COM through the phone number 1-877-886-5989.The information
is listed on the front of manual.

Note: Use only original replacement
parts. This will protect your warranty
coverage for parts replaced under
warranty.
PARTS UNDER WARRANTY
Contact authorized dealer from
whom you purchased this product.
If they are unable to supply original
replacement part(s), call the number on the front of this manual. When
contacting your dealer or PRO-COM,
have ready:
l your name
l your address
l model and serial numbers of
your heater
l how heater was malfunctioning
l type of gas used (propane/LP or
natural gas)
l purchase date
l warranty card
Usually, we will ask you to return the
defective part to the factory.

SERVICE HINTS
When Gas Pressure Is Too
Low
lPilot will not stay lit
l Burner will have delayed ignition
lHeater will not produce specified
heat

EQUIPMENT SHUTOFF VALVE
For all models. Equipment shutoff
valve with 1/8" NPT tap.

When Gas Quality Is Bad
l
l
l

Pilot will not stay lit
Burner will produce flames and
soot
Heater will backfire when lit

You may feel your gas pressure is
too low or the gas quality is poor. If
so, contact your local natural gas
supplier.

ACCESSORIES
Purchase these heater accessories from your local dealer. If they
can not supply these accessories,
contact PRO-COM for information.
You can also write to the address
listed on the front of this manual.

PARTS NOT UNDER
WARRANTY
FLOOR MOUNTING STAND
Models MN060HBA,MN100HBA,
MN100TBA
For locating heater on the floor away
from a wall. Complete installation
instructions provided with floor
mounting stand.

1 7

Contact authorized dealers of this
product. If they can’t supply original
replacement part(s), contact PRPCOM through the phone number 1877-886-5989.

ILLUSTRATED PARTS
BREAKDOWN
MN060HBA

1 8

PARTS LIST

This list contains replaceable parts for your heater. When ordering replacement
parts, follow the instructions listed under Replacement Parts on page17 of this
manual.

MN060HBA
KEY
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
23-1
23-2
24
25
26
27
28
29

QTY.

PART NO.

DESCRIPTION

MB10008
MB09003
MB11005
ML086-03
ML087-03
ML088-03
ML069-02
NV2020-12
ML073-01
ML029-01
MB16002
NRV81FI-3
ML079-01
ML119-01
MB40033
MB40045
MB40043
ML101-02
ML091-06
ML103-02
ML129-02
ND1103x600x9
ND0803-6
ND0807
ML105-01
6170-5Z
MB29003
ML084-03
ML060-02
ML083-03

Cabinet Assembly
Lower Front Panel Assembly
Reflector Unit
Glass
Upper Glass Retainer
Lower Glass Retainer
Self Tapping Screw
Control Valve
Ignitor Line
Control Valve Fixed Nut
Control Knob Assembly
Pressure Regulator
Self Locking Screw
Pressure Tap
Main Inlet Tube Assembly
ODS Line Assembly
Gas Outlet Tube Assembly
Burner
Burner Connector
Injector
Left Burner Support Bracket
Regulator Mounting Bracket
ODS/Pilot Assembly
Thermocouple
Ignitor Electrode
ODS Deflector
Nut
Grill Guard
Middle Panel
Mounting Bracket
Ignitor Assembly

1
1
1
1
1
1
12
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1

MB28001
ML070-11
ML071-01

Assembly Hardware
CSA/AGA Label
Gas Instruction Decal

1
1
1

NBB10-000M1

1 9

ILLUSTRATED
PARTS BREAKDOWN
MN100HBA

2 0

PARTS LIST

This list contains replaceable parts for your heater. When ordering replacement
parts, follow the instructions listed under Replacement Parts on page17 of this
manual.

MN100HBA
KEY
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
22-1
22-2
23
24
25
26
27
28

QTY.

PART NO.

DESCRIPTION

MB10008
MB09003
MB11005
ML086-03
ML087-03
ML088-03
ML069-02
NV2020-1213
ML073-01
ML029-01
MB16002
NRV81FI-3
ML079-01
MB40034
MB40056
MB40054
ML101-01
ML091-05
ML103-02
ML129-02
ND1103x600x9
ND0803-6
ND0807-B2
ML105-01
6170-5Z
MB29003
ML084-03
ML060-02
ML083-03

Cabinet Assembly
Lower Front Panel Assembly
Reflector Unit
Glass
Upper Glass Retainer
Lower Glass Retainer
Self Tapping Screw
Control Valve
Ignitor Line
Control Valve Fixed Nut
Control Knob Assembly
Pressure Regulator
Self Locking Screw
Main Inlet Tube Assembly
ODS Line Assembly
Gas Outlet Tube Assembly
Burner
Burner Connector
Injector
Left Burner Support Bracket
Regulator Mounting Bracket
ODS/Pilot Assembly
Thermocouple
Ignitor Electrode
ODS Deflector
Nut
Grill Guard
Middle Panel
Mounting Bracket
Ignitor Assembly

1
1
1
1
1
1
12
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1

MB28001
ML070-13
ML071-01

Assembly Hardware
CSA/AGA Label
Gas Instruction Decal

1
1
1

NBB10-000M1

2 1

ILLUSTRATED PARTS
BREAKDOWN
MN100TBA

2 2

PARTS LIST

This list contains replaceable parts for your heater. When ordering repalcement
parts, follow the instructions listed under Replacement Parts on page17 of this
manual.

MN100TBA

KEY
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
26-1
26-2
27
28

QTY

PART NO.

DESCRIPTION

MB10007
MB09003
MB11005
ML086-03
ML087-03
ML088-03
ML069-02
SIT544-130
ML111-02
6170-5Z
845-4.8x60Z
MB29003
ML079-01
ML084-03
NRV81FI-3
ML073-01
ML060-02
MB40048
MB40049
MB40050
NBB10-000M1
ML101-01
ML091-05
ML103-02
ML129-02
ND1103x800x9
ND0803-8
ND0807-B2
ML105-01
ML083-03

Cabinet Assembly
Lower Front Panel Assembly
Reflector Unit
Glass
Upper Glass Retainer
Lower Glass Retainer
Self Tapping Screw
SIT Thermostat Valve Assembly
Thermostat Valve Base/Bracket
NUT
Screws
Grill
Self Locking Screw
Middle Panel
Pressure Regulator
Ignitor Line
Mounting Bracket
Main Inlet Tube Assembly
ODS Line Assembly
Burner Inlet Tube Assembly
Burner
Burner Connector
Injector
Left Burner Support Bracket
Regulator Mounting Bracket
ODS/Pilot Assembly
Thermocouple
Ignitor Electrode
ODS Upper Deflector
Ignitor Assembly

1
1
1
1
1
1
12
1
1
2
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1

MB28001
ML160-19
ML071-01
ML065-01

Assembly Hardware
CSA/AGA Label
Gas Instruction Decal
Thermostat Sensing Bulb Clip

1
1
1
1

2 3



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Title                           : F:\manual\2005年~1\PRO-CO~1\PR7
Author                          : lenovo
Creator                         : pdfFactory Pro www.fineprint.com.cn
Producer                        : pdfFactory Pro 2.10 (Windows XP Chinese)
Create Date                     : 2008:03:07 14:13:53
Page Count                      : 24

EXIF Metadata provided by EXIF.tools