Profile Cd Player Am Fm High Power Detachable Face Users Manual Graphic2

CD8200 to the manual facabd0d-8df9-4fb5-bb5b-34fae913797c

: Profile Profile-Cd-Player-Am-Fm-High-Power-Detachable-Face-Cd-Player-Users-Manual-520794 profile-cd-player-am-fm-high-power-detachable-face-cd-player-users-manual-520794 profile pdf

Open the PDF directly: View PDF .
Page Count: 20

AM/FM HIGH POWER DETACHABLE FACE

CD PLAYER

CD8200

INSTALLATION INSTRUCTIONS / OWNER S MANUAL

,

1

Serial # Purchase Date

INTRODUCTION

Congratulations on your purchase of a Profile state-of-the-art single disc CD

player. Your selection of a Profile car audio product indicates a true appreciation

of fine musical reproduction. Whether adding to an existing system or including

your Profile CD player in a new system, you are certain to notice immediate

performance benefits.

FEATURES

35W x 4 Power Output Loud Function

Auxiliary RCA Line Input ISO/DIN Mounting

Clock Blinking Security L.E.D.

30 Station Memory Full Electronic Function Controls

4 Band Preset Equalizer Disc Scan, Random & Repeat Play

KEEP YOUR SALES RECEIPT

Take this time to attach your sales receipt to the manual and put in a safe place.

In case of any reason this product may need warranty service, your receipt will

be necessary to establish purchase date.

IMPORTANT! Before making any connections, disconnect the car s battery

until the installation is completed to avoid possible damage to the electrical

system.

Serial # Purchase Date

,

Dual RCA Line Output(Front & Rear) Power Level Meter

2CD8200

SAFETY PRECAUTIONS

Secure the CD player

When installing your CD player in the vehicle, make sure it is mounted properly in the dash,

using an after market installation kit if needed. When using the supplied mounting sleeve,

it is a must that you also use the supplied back brace to support the back of the CD

player.

Use caution when mounting the CD player.

Remember there are many electrical wires, vacuum lines, brake lines and air bag deployment

wires. Make sure you know where they are when mounting the CD player to avoid puncturing

lines, and shorting wires.

Use high grade wire connectors.

To ensure maximum power transfer and secure safe connections, it is recommended to use

high grade barrel or crimp cap connectors.

Do not run any wires underneath the vehicle.

Exposed wires can be cut or damaged. It is best to run all wires through the vehicle under the

carpet and/or side panels. This enables to a cleaner installation and less risk of damage.

Run signal wires away from electrical wires

To avoid possibility of induced noise from the car's electrical system (i.e. popping noises or

engine noise), run signal wires away from the car's electrical wiring.

Make all ground wires as short as possible and terminated at the same point.

In order to reduce the chance of ground loops (i.e. engine noise), make the grounded wire as

short as possible to reduce the wire's resistance. Also, when using multiple components, make

sure all units are grounded at the same point.

Avoid sharp edges when running the wires.

To avoid the possibility of power, signal or speaker shorts, be careful not to allow the amplifier

wires to come in contact with sharp edges. Use a grommet to protect the wire when running

through the fire wall .

.

3

CARE AND MAINTENANCE

PROTECTIVE CASE

( FIG.2)

Press the OPEN button to detach the face plate, then take the face plate away

from the head unit (Fig.1) and put it in the protective case (Fig.2) for safe keeping.

FACE PLATE

OPEN BUTTON

( FIG.1)

Cleaning the CD player

When cleaning the vehicle, be sure not to get any water in or on the CD player. Clean only

the exterior surface of the unit with a dry, clean soft towel using no chemical solvents.

Operating in extreme temperatures

Sometimes the unit will not operate in extreme, hot or cold temperatures. If this is the case,

wait until the temperature in the vehicle is normal, then resume operation.

Protect your CDs.

When not using the disc player, it is recommended that you remove the CD.

Do not leave an ejected disc sitting on the edge of the disc player for long periods of time.

The disc will warp under direct sunlight. Always put each disc in its case to protect them

during times of non-use.

CD operation.

Never attempt to force anything other than a compact disc in the disc slot. This disc player

is a precision instrument that could be damaged by a foreign object.

Disc skip

When driving down a very rough road, the disc may skip. This will not scratch or damage the disc.

Removing and protecting detachable face plate.

The face plate of the radio may be removed as a theft deterrent. After removing the face

plate, use the case provided to keep the face plate from getting damaged.

FACE PLATE

4CD8200

DISC CARE AND PLAY:

Before playing, clean the disc with a clean, lint-free cloth.

Wipe the disc in the direction of the arrow.

Do not use solvents such as benzine or thinners. Commercially available

cleaners or anti static spray will damage the unit.

Insert a disc with the labeled surface up.

Do not try to insert another disc when one has already been inserted.

Doing so may damage the unit.

Label

surface up

Handle the disc by its edge to keep the disc clean and do not touch

the surface.

Do not stick paper or tape on the disc.

Do not expose the disc to direct sunlight which can cause the disc to warp.

Always store the disc in its case for protection. Scratched up discs will

produce poor sound performance and cause CD player to skip.

5

ELECTRICAL AND SIGNAL CONNECTIONS

FOUR SPEAKER SYSTEM

! Connect Black wire to chassis ground.

! Connect the Yellow memory backup wire to a Constant +12 Volt power source wire.

! Connect the Red ignition wire to a switched +12 Volt power source wire. (The power

wire that is energized when the key is in the accessory position).

! The blue wire is connected only if a power antenna or an amplifier is used in the

system. This wire supplies +12 Volt output when the CD Player is turned on,

which activates most power antenna relays or amplifier turn on circuits.

++

++++

++

YELLOW

ANTENNA CONNECTOR

MEMORY +12V

BLACK(GND)

RED (B+)

FRONT RIGHT

SPEAKER

BLUE AUTO ANTENNA

WHITE

WHITE/BLACK

GREEN/BLACK VIOLET/BLACK

GRAY/BLACK

GRAY

VIOLET

GREEN

1OA Fuse

FILTER

BOX

0.5A Fuse

BATTERY

+12V

+-

SWITCHED +12V

(ON WITH IGNITION)

Low level signal output for

connection to amplifier or

signal processors.

R

L

R

L

R CH RED

L CH WHITE

R CH RED

L CH WHITE

BLACK

GRAY

FRONT RCA OUTPUT

REAR RCA OUTPUT

REAR RIGHT

SPEAKER

FRONT LEFT

SPEAKER

REAR LEFT

SPEAKER

FUSE

0.5 A

R

L

R CH RED

L CH WHITE BROWN

AUX RCA INPUT

Before making the following connections, take time to look over the vehicle's wiring and

determine the location and wires you will be connecting to. If you do not wish to cut or tap

into the vehicles existing factory wiring, there are wiring kits available at your car audio

retailer that will allow you to plug directly into the factory wiring harness. Make sure to

test all wires before connecting to the CD Player.

6

CAUTION! Tape unused wires so they do not short against other wires or

chassis ground.

TWO SPEAKER SYSTEM

CD8200

NOT USED

NOT USED

NOT USED

NOT USED

++++

YELLOW

ANTENNA CONNECTOR

MEMORY +12V

BLACK(GND)

RED (B+)

FRONT RIGHT

SPEAKER

BLUE AUTO ANTENNA

WHITE

WHITE/BLACK GRAY/BLACK

GRAY

BATTERY

+12V

+-

SWITCHED +12V

(ON WITH IGNITION)

Low level signal output for

connection to amplifier or

signal processors.

R

L

R

L

R CH RED

L CH WHITE

R CH RED

L CH WHITE

BLACK

GRAY

FRONT RCA OUTPUT

REAR RCA OUTPUT

FRONT LEFT

SPEAKER

FUSE

0.5 A

10A Fuse

FILTER

BOX

0.5A Fuse

R

L

R CH RED

L CH WHITE BROWN

AUX RCA INPUT

7

MOUNTING THE CD PLAYER

DIN SLEEVE MOUNTING

Insert the mounting sleeve into a

standard DIN cutout in the dash

kit, dashboard or Console.

Bend the mounting tabs of the sleeve

with a screwdriver to secure the bracket

firmly in place.

Insert the CD Player in the

mounting sleeve until it locks.

There are two different ways to mount the CD Player. In most Japanese vehicles you can

use the factory mounting brackets, taking advantage of the ISO/DIN opening. If your vehicle

does not have ISO/DIN opening, you can mount the CD Player using the supplied DIN sleeve

and rear support bracket. When considering your mounting location, make sure the unit will

be leveled. If you cannot mount the CD Player level, due to your vehicles design, make sure

there is no more than a 30 degree tilt. Keeping this in mind will assure proper CD play and

overall reliability.

8CD8200

Attach the back brace to the CD

player using the supplied hardware.

Then attach the other end of the

brace to a firm mounting surface

(i.e. Dash brace, fire wall, e.t.c.)

This will brace the back of the CD

player to ensure solid mounting to

prevent theft and provide optimal

CD play.

To Attach the Face Plate:

1 Insert the face plate with the right side first.

Angle in the right side of the plate to the unit.

2 Then push in the left side of the face plate

until it snaps in place.

Once the CD player is secured, fit the trim

ring over outside edge of the radio until it

snaps into place.

FACE PLATE

9

REMOVING THE CD PLAYER

Remove the rectangular trim ring by

applying pressure with your finger

tips, then gently pull out away from

the dash.

PLACE FINGER TIPS HERE

ISO/DIN MOUNTING

If you own a Japanese vehicle, you can use the standard ISO/DIN mounting screw holes on

the side of the CD player to attach to the existing factory mounting bracket, without using

the provided DIN sleeve.

Remove the factory ISO/DIN mounting bracket from the car along with the factory radio.

Remove the factory radio from the bracket by unscrewing the two Phillips screws on each

side of the radio paying close attention to their screw positions and saving the screws to

mount the CD player.

Remove the two spring clips from each side of the CD player by removing the screws.

These clips are not used in ISO/DIN mounting method and must be removed to expose the

ISO/DIN mounting holes.

Also remove the detachable face and rectangular trim ring from the CD player and mount

the CD player to the factory ISO/DIN bracket using the screws that you removed from

the factory radio.

Connect the wire harness and antenna plug to the back of the CD player. Then mount the

factory ISO-DIN bracket to the car.

Note: It is not necessary to attach the outer rectangular trim ring for ISO/DIN mounting

method.

!

!

!

!

!

To remove the CD player from an ISO/DIN mount, follow the above mounting procedure

in reverse order.

To remove the CD player from a sleeve mount, use the pair of keys provided.

!

!

Insert the provided removal key into the opening on each side of the CD player.

Push the keys inward until they snap in place. Firmly grab the keys and slowly

pull the CD player out away from the dash.

10 CD8200

LOCATION AND FUNCTION OF CONTROLS

11

1 POWER

To turnONthe unit, press any button except the and button.

To turnOFFthe unit, press the button for more than 2 seconds.

2 DETACH FACE PLATE

Press the button to detach the face plate. This will allow you to remove

the face plate.

3 CD PLAY

To play a CD, gently insert the CD into the slot with the label side facing up. The

disc will automatically be loaded into the unit and start playing the first track of

the disc. The digital display will indicate the track number.

4 EJECT CD

To remove a CD once inserted, press the button. Once the CD is ejected,

the unit switches to radio mode.

5 VOLUME UP

Press the button to increase the system s volume.

6 VOLUME DOWN

Press the button to decrease the system s volume.

7 MODE

Press the MOD button to change among tuner (radio), CD (if disc is loaded),

and auxiliary input playing mode.

Radio CD AUX.

8 BAND

Under radio mode press the BND button to change between three FM bands and

two AM bands.

FM 1 FM 2 F M 3 AM 1 AM 2

9 10 RADIO TUNE & CD TRACK UP/DOWN, CD FAST FORWARD/REWIND

Under radio mode, press the 9 or 10 button momentarily and repeatedly

to change the frequency number up or down one step. Under SEEK 1 mode, press

and hold the 9 or 10 button for more than 2 seconds to seek to the next or

previous clear station. Under SEEK2 mode, press and hold the 9 or 10 button

to speedily change stations up or down. Changing stations will stop once the button

is released. (Please refer to on page 13 on how to set the seek mode

between SEEK 1 and SEEK 2.)

,

,

+

-

I

I

I

I

I

I

12

In CD play mode, press and hold the 9 or 10 button to fast forward or

fast reverse through the song. The CD resumes playing when the button is released.

11 PRESET STATIONS

There are 6 numbered buttons to store into memory and recall stations for each

band. Select a band (if needed) as explained in 8 . Tune to a radio station that

you wish to store. Select, press, and hold a preset numbered button for 2 seconds

until you hear a beep indicating that the station has been stored in memory. To

recall a preset station, simply push the numbered preset button.

12 FUNCTION SELECT

SEL button allows you to display different functions for adjustments. Press the

SEL button momentarily and repeatedly to move the display from Volume, Bass,

Treble, Balance, and Fader functions. Use the 5 and 6 buttons to

adjust the selected mode. When the mode has not been adjusted for several

seconds, display and mode returns to normal radio or CD operation.

VOL BAS TRE BAL FAD

(Volume) (Bass) (Treble) (Balance) (Fader)

VOLUME - Press the SEL button once. Adjust the volume level using the 5

and 6 buttons.

BASS - Press the SEL button twice. Adjust the bass level using the 5 and

6 buttons.

TREBLE - Press the SEL button three times. Adjust the treble level using the

5 and 6 buttons.

BALANCE - Press the SEL button four times. Adjust the sound balance between

left and right speakers using the 5 and 6 buttons.

FADER - Press the SEL button five times. Adjust the sound balance between front

and rear speakers using the 5 and 6 buttons.

Press the SEL button for more than 2 seconds to display additional set of functions

for adjustments, such as DSP, Beep On/Off, SEEK 1 or 2, 12 Hour/24 Hour, and

Volume Last/Adjust.

DSP - The unit is equipped with 4 preset equalization modes. Press the SEL button

for more than 2 seconds to display DSP OFF. Then use 5 button to

choose one of 4 following preset EQ s in the following order.

When using preset EQ modes you will not have access to Bass and Treble

settings.

DSP OFF POP ROCK CLASSIC FLAT

CD8200

I

I

+-

+

-+

-

+-

+-

+-

,+

In CD play mode, press the 9 or 10 button to move to the next or previous

track.

I

I

13

BEEP - The beep sound when you press a button on the unit can be turned on or

off. Press the SEL button for more than 2 seconds to display the DSP

function. Press the SEL button again momentarily to display BEEP ON/OFF.

Then use 5 button to turn on/off the beep sound.

SET VOL - A certain volume level can be set to come on when the unit is turned

on or can be set to come on at the same last level before the unit was

turned off. Press the SEL button for more than 2 seconds to display

the DSP function. Press the SEL button four times momentarily to

display VOL LAST/ADJ. Use 5 button to choose between VOL LAST

and VOL ADJ. To set the volume to a certain level, press the

SEL button momentarily when VOL ADJ is displayed. Then use 5

and 6 buttons to adjust to certain volume level when A-VOL is

displayed.

13 CD TOP/PAUSE

In CD play mode, press the TOP 13 button to pause CD play. Press again to

resume normal play.

In CD play mode, press the TOP 13 button for more than 2 seconds to go back

to the top of the disc and play the first track.

14 CD SCAN

In CD play mode, press the INT 14 button to turn on intro playing first 10

seconds of each track. When wish to listen to the whole track during intro mode,

press the button again to turn off intro.

SEEK- The unit is equipped with two types of seeks, SEEK 1 and SEEK 2, for radio

stations. Press the SEL button for more than 2 seconds to display the BEEP

function. Press the SEL button twice momentarily to display SEEK 1 or 2.

Then use 5 button to switch between SEEK 1 and SEEK 2.

(This adjustment is only available during radio operation)

SEEK 1 mode: Pressing 9 or 10 button for more than 2 seconds will seek

up or down to the next strong station during radio operation.

SEEK 2 mode: Pressing 9 or 10 button continuously will speedily change

station up or down until the button is released.

12 H / 24 H- The unit is equipped with two types of clock formats, 12 Hour and 24

Hour. Press the SEL button for more than 2 seconds to display the DSP

function. Press the SEL button three times momentarily to display 12H

or 24 H. Then use 5 button to choose between 12 H and 24 H.

15 REPEAT PLAY

In CD play mode, press the RPT 15 button to continuously playing the current

track. Press it again to cancel the repeat feature.

+

+

+

-

I

I

I

I

+

+

14

16 RANDOM PLAY

In CD play mode, press the RDM 16 button to play all tracks of the disc in random

sequence. Press it again to cancel random play.

17 LOUDNESS

Press LOU button once to enhance the bass effect.

Press again to cancel the loudness effect.

18 AUTOMATIC STORING & PRESET SCANNING

In radio mode, press and hold the A.P. 18 button for more than 2 seconds to

activate the automatic storing function. Once activated, the radio starts search-

ing for first 6 strong signaled stations and stores them into the preset memory.

After completion, the radio will tune back to the first preset memory station.

In radio mode, press the A.P. 18 button momentarily to activate the preset

scanning function. Once activated, the radio starts scanning all preset memory

stations for few seconds at a time while the preset memory number flashes on

the LCD. Pressing the button again will stop the scan.

19 MUTE

Press the MU button to silence the system. Press a second time to resume

listening.

20 MONO/STEREO

Monaural (Mono) or Stereo mode can be selected for FM tuner s reception. For

best quality sound, stereo mode should be selected. However, Mono mode can be

selected to help the reception of distant radio stations. Press the ST button to

select between Mono and Stereo modes.

21 CLOCK

Press the CLK button to display the time on the LCD for 5 seconds. To adjust the

time, press and hold the CLK button until the hour flashes and use the 5 and

6 buttons to adjust the hour. Press and hold the CLK button again until the

minute flashes and use the 5 and 6 buttons to adjust the minute.

22 RESET

The reset button should be pressed when installation is complete and also when

all buttons do not operate.

23 SECURITY LED

Designed as a theft deterrent, the red LED will flash when the unit is turned off

and face plate removed.

,

CD8200

+

-

-

+

15

TROUBLE SHOOTING THE SYSTEM

The following chart will help in solving most problems that may occur. Should any problem

persist after you have made these checks, please consult your nearest Profile retailer.

Before going through this check list, refer back to the wiring and operating procedures.

SYMPTOM CAUSE SOLUTION

The vehicle's ignition switch

is not on.

Turn the ignition switch to the accessory

position. If there is still no power, check the

fuses at the vehicle's fuse block or the

radio's fuse leads.

The fuse is blown. Replace the fuse with another fuse of the

same recommended value

There is a disc already in

the player.

Remove the disc in the player, then put in

the new one.

You are trying to put the

compact disc in upside down.

Insert the compact disc with the label facing

up.

The compact disc is

extremely dirty or

defective.

Clean the compact disc with a compact disc

cleaning solution or replace the defective

compact disc.

The temperature in the car

is too hot.

Cool the inside of the vehicle, then try again.

Condensation build-up on the

inside of the unit.

Leave the disc player off and turn the

vehicle's air conditioner on to remove the

condensation build-up inside the unit.

The volume control is all the

way down.

Adjust the volume control.

The speakers are bad. Test the speakers to determine if they need

replacing.

The function

buttons do

not work.

The built-in microprocessor

is operating incorrectly.

Remove the disc, then re-insert it. Press the

reset button .

No Power

Disc cannot

be loaded or

ejected.

No sound.

New installation. Press the RESET button.

E 1~ E 10

The unit cannot be operated because of trouble. Press the "RESET"

button . If the indicator still appears after pressing the "RESET"

Button , your unit needs repair. Please refer to the warranty section

of this manual for details on getting the unit serviced.

ERROR CODES

22

22

22

22

SYMPTOM CAUSE SOLUTION

The installation angle is

greater than 30 degrees

Adjust the angle of the unit to less than 30

degrees

The disc player is installed

incorrectly

Check to see if the unit is fastened securely

with the back brace supporting the rear of

the unit.

The compact disc is

extremely dirty or defective

disc.

Clean the compact disc with a compact disc

cleaning solution or replace the defective

compact disc.

Condensation build-up on the

inside of the unit.

Leave the disc player off and turn the

vehicle's air conditioner on to remove the

condensation build-up inside the unit.

The antenna is not

connected or the antenna is

bad.

Check the antenna and connection to insure

proper performance.

The signals in your listening

area are weak.

Select stations manually and make sure the

tuner is in the distant stereo mode.

The radio

does not

work. The

Radio station

automatic

selection

does not

work.

The compact

disc skips.

16 CD8200

SPECIFICATIONS

GENERAL

Power Supply Requirements...........................................DC 12 Volts, Negative Ground

Chassis Dimensions ...................................................................7 (W) x 6 1/2 (D) x 2 (H)

Tone Controls...........................................................................................................................

Bass @ 100Hz..........................................................................................+10dB / -10 dB

Treble @ 10Khz.......................................................................................+10dB / -10 dB

Equalizer..................................................................................................................4 Presets

Maximum Output Power.........................................................................................35W x 4

RMS Output Power..................................................................................................20W x 4

Maximum Current Consumption........................................................................10 Ampere

Fuses

Memory (Constant)........................................................................................10 Ampere

Accessory (Switched).................................................................................0.5 Ampere

RCA line out voltage......................................................................................................3.7 V

CD PLAYER

Signal to Noise Ratio...................................................................................................>85dB

Channel Separation......................................................................................................>80dB

Frequency Response........................................................................................5Hz ~ 20Khz

Usable Disc....................................................................................CD/CD-R/CD-RW Discs

RADIO

FM

Frequency Coverage..............................................................................87.5 to 107.9MHz

IF................................................................................................................................10.7MHz

Station Presets...................................................................................................................18

AM

Frequency Coverage.................................................................................530 to 1710KHz

IF.................................................................................................................................450KHz

Station Presets...................................................................................................................12

Due to continuing product improvement, specifications subject to change without notice.

17

|||| |||| ||||

LIMITED WARRANTY

Profile Consumer Electronics, Inc. warrants this product to be free from defects in

material and workmanship for a period of One (1) Year from the date of sale to the

original consumer purchaser. If this product is proven to be defective within this one

year period, Profile will repair it when said product is returned, with a copy of the

dated sales receipt, freight prepaid to Profile.

This warranty is valid only in the United States. This warranty does not cover any

expense incurred in the removal and/or re-installation of this product. This warranty

does not cover any Profile product damaged by accident, misuse, abuse, improper line

voltage, fire, water, lightning, or other acts of God. This warranty is void if any parts

and/or service is/are furnished by anyone other than Profile. This warranty is void if

the factory applied serial number is altered or removed from the product.

This warranty does not cover cartons, cases, batteries, broken or marred cabinets,

magnetic tapes, or any other accessories used in connection with this product or

consequential damages due to a defect in the product.

Any implied warranties, including fitness for use and merchantability, are limited in

duration to the period of the express warranty set forth above. No person is

authorized to assume for Profile any other liability in connection with the sale of the

product. Profile expressly disclaims liability for incidental and consequential

damages that might be caused by this product. The remedies provided under this

warranty are exclusive and lieu of all others.

This warranty gives you specific legal rights. You may have other rights which vary

from state to state or province to province. Some states or provinces do not allow

limitation on how long warranties last, so the above may not apply to you. Additionally,

some states/provinces do not allow the exclusion to limitation of consequential or

incidental damages, so the above limitation or exclusion may not apply to you.

* In the space below, record the serial number that is located on the back of the unit

along with the purchase date and location.

Model Number __________________ Serial Number

____________________

Purchase Date __________________ Where Purchased _________________

RETAIN YOUR SALES RECEIPT ALONG WITH THIS CARD. IT IS YOUR ONLY

VALID DOCUMENT TO RECEIVE WARRANTY SERVICE.

PROFILE CONSUMER ELECTRONICS, INC.

15060 SHOEMAKER AVE

SANTA FE SPRINGS, CA 90670

TEL: (562)404-9393 FAX: (562)404-9433

WWW.PROFILEUSA.COM

WARRANTY REPAIR POLICY

In the unlikely event of product failure, the following procedures

should be followed

1) The unit must be under the 1-year warranty period.

2) The unit must have no physical damage.

3) A copy of the original proof of purchase must be sent with the unit.

4) Include a brief description of the problem or failure with the unit.

5) Include the return street address and daytime telephone number.

6) Allow 2~3 weeks for repair (this period includes shipping time).

Send unit to: PROFILE CONSUMER ELECTRONICS, INC.

15060 SHOEMAKER AVE

SANTA FE SPRINGS, CA 90670

TEL: (562) 404-9393

Note: All units failing to meet the above requirements will be

subject to a charge and or may not be repaired.