Proform 831293062 User Manual 580X Manuals And Guides L0704151

PROFORM Treadmill Manual L0704151 PROFORM Treadmill Owner's Manual, PROFORM Treadmill installation guides

831.293062 L0704151

User Manual: Proform 831293062 831293062 PROFORM PROFORM 580X - Manuals and Guides View the owners manual for your PROFORM PROFORM 580X #831293062. Home:Fitness Equipment Parts:Proform Parts:Proform PROFORM 580X Manual

Open the PDF directly: View PDF .
Page Count: 30

Download
Open PDF In Browser	View PDF

ModelNo.831.293062
SerialNo.
i SerialNumberDecal

TREADMILL

EXERCISER
User's Manual

• Assembly
• Operation
• Maintenance
• Part List and Drawing

A_,CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference,

Sears, Roebuck

and Co., Hoffman

Estates,

IL 60179

TABLE OF CONTENTS

Note: An EXPLODED DRAWING is attached in the center of this manual.

IMPORTANT PRECAUTIONS
WARN ING: Toreduce
theriskofburns,
fire,elect.°shock,
orinjury
topersons,
read
the
following

important

precautions

and information

1. it is the responsibility
of the owner to ensure
that all users of this treadmil! are adequately
informed of all warnings and precautions.
2. Use the treadmill

only as described.

Place the treadmill on a Jove1 surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill,
4.

Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.

5, Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
6. Keep children under the age of 12 and pets
away from the treadmill at aH times.
7. The treadmill should be used only by persons
weighing 250 pounds or lesso
8. Never allow more than one person on the
treadmill at a time.
9. Wear appropriate exercise clothes when
using the treadmill
Do not wear loose clothes
that could become caught in the treadmill
AtHetic support clothes are recommended for

before operating

the treadmill

both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
10. When connecting the power cord (see page 8),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance shouJd be on
the same circuit. Do not use an extension cord,
11. Use only a sing_e-outlet surge suppressor that
meets all of the specifications
described on
page 8. To purchase a surge suppressor, see
your local Sears or cal_ 1-800-366=1218 and
order part number 146148.
12. Failure to use a properly functioning surge
suppressor could resuJt in damage to the con=
trol system of the treadmill if the controt system is damaged, the walking belt may change
speed or stop unexpectedly, which may result
in a fall and serious injury.
13. Keep the power cord and the surge suppressor away from heated surfaces.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working proper_y. (See BEFORE YOU BEGIN on page 4 if the treadmill is
not working properlyo)

15. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
17. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord and move the on/off circuit
breaker to the off position when the treadmill
is not in use. (See the drawing on page 4 for
the location of the on/off circuit breaker.)

21. When using iFIT.com CDs and videos, you
can manually override the speed setting at
any time by pressing the speed buttons.
However, when the next "chirp" is heard, the
speed will change to the next setting for the
CD or video program.
22. Remove iFIT.com CDs and videos from your
CD player or VCR when you are not using
them.
23. Inspect and properly tighten all parts of the
treadmill regularly.
24. Never insert any object into any opening.

18. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 5, and HOW TO FOLD
AND MOVE THE TREADMILL on page 21.)
You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
19. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
20. When using iFIT.com CDs and videos, an
electronic "chirping"
sound will alert you
when the speed of the treadmill is about to
change. Always listen for the "chirp" and be
prepared for speed changes. In some instances, the speed may change before the
personal trainer describes the change.

I_AI_I/,._I_I_
.
25. I./P_l_ll_jir_r_.
Always unplug the power
cord immediately after use, before cleaning the
treadmill, and before performing the maintenance and adjustment procedures described in
this manual. Never remove the motor hood unless instructed to do so by an authorized service representative. Servicing other than the
procedures in this manual should be performed
by an authorized service representative only.
26. This treadmill is intended for in-home use
only. Do not use this treadmill in a commercial, rental, or institutional setting.

SAVE THESE INSTRUCTIONS

A_WARNIN
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. Sears assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.

The decals shown have been placed on your treadmill. If a
decal is missing, or if it is not legible, please call toll-free
1 °800°999°3756 to order a free replacement decal. Apply the
decat in the location shown. Note: The decats are not
shown at actual size.

Prolect yoursell and
others from risk of serious

-Standonl on _e
_t_ tlrll_,l_
r °ppig

•Poldhan_,ailsto
p eve_,t _11ng a_,d
sa_/y di_ while

,St0_ if you f_el _il,t

_,_ath

,-,11 is r_o_ed o
•_ed_ce idne _ ts
I_,t
I_el b,,f0r
Mdi, g trr ad,_ll rd_

a eu_d treadmill

fin_ers and hair
_ belt¸

i_ismoving
-Alwa swear

BEFORE YOU BEGIN
Thank you for selecting the revolutionary PROFORM _
580X treadmill. The 580X treadmill combines advanced technology with innovative design to help you
get the most from your exercise program in the convenience and privacy of your home. And when you're not
exercising, the unique 580X treadmill can be folded up,
requiring less than half the floor space of other treadmills.

ing this manual, call 1-800-4-MY-HOME _'_
(1-800-4694663).To help us assist you, please note the product
model number and serial number before calling. The
model number of the treadmill is 831.293062. The serial number can be found on a decal attached to the
treadmill (see the front cover of this manual for the location).
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.

For your benefit, read this manual carefully before
using the treadmill
if you have questions after read-

CD Holder
Accessory Tray
Fan

Console

Handrail
Storage Latch

Key/Clip

Upright

On/Off
Breaker

Walking Belt
Foot Rail
RIGHT SiDE
_

BACK
I
Rear Roller
Adjustment Bolts

Cushioned Walking Platform
for maximum exercise comfort

Assembly requires two persons, Set the treadmill in a cleared area and remove all packing materials, Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is
coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the
top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,
non-abrasive cleaner.
E

Assembly

requires

and wire cutters

the included allen wrenches

_:- _:_

_ and your own phillips

screwdriver

1. Make sure that the power cord is unpmugged.

To Bdentify small parts, use the PART IDENTIFICATION CHART on page 27. Note: If a part is not in the
parts bag, check to see if it has been pre-assembled. If
a part is missing, call toll4ree 1-800-999-3756.
With the help of a second person, carefully raise the
Upright Base (97) to the position shown. Insert one of
the Extension Legs (92) into the Upright Base. (Note: It
may be helpful to tip the Upright Base forward as you insert the Extension Leg.) Make sure that the Warning
Decal (91)is in the location shown.
Insert the other Extension Leg (not shown) in the same
way.

97
92

2. With the help of a second person, carefully tip the
Upright Base (97) down as shown. (Note: It may be helpful to place your foot on one of the Extension Legs [92]
as you tip the Uprights.) Make sure that the Extension
Legs remain in the Uprights.

Attach each Extension Leg (92) with two Extension Leg
Bolts (96) and two 1/4" Washers (39) as shown. Thread
a Leveling Foot (95) into each side of the Upright Base
(97); do not thread the Leveling Feet fully into the
Upright Base.
Attach the two Base Pads (99) to the Upright Base (97)
in the locations shown with two 1" Tek Screws (40).
With the help of a second person, raise the Upright Base
(97) to the vertical position.

97
39
96

3. Attachthe LatchAssembly(82)totheLeftUpright(84)
withthetwoLatchScrews(46).StartbothLatchScrews
beforetightening
eitherofthem.Note:TheLatchScrews
maybepreattached
tothe LeftUpright.
82

4. Refertostep6 andlocatethefourUprightBolts(86).
LoosentheUprightBoltstwotothreeturns.
Refertodrawing4c.Withthehelpof a secondperson,
holdtheConsoleBase(101) nearthe Uprights(80,84).
LookundertheConsoleBaseandlocatethewireson
thesidesoftheConsoleBase.Makesurethatthewires
arenot routedthroughtheopeningsfortheTrays(109,
111). Drawing4ashowsthecorrectrouteforthewires.
Drawing
4bshowsanincorrectroute.

i..........

Correct

Incorrect

Refertodrawing4c.CuttheplastictiesholdingtheWire
Harness(74)andthe PulseWirein theUprights(80,84).
ConnecttheWireHarnessandthe PulseWiretothe
wiresonthesidesoftheConsoleBase(101).Makesure
to connectthe connectorsproperly(seethe inset
draw{rigs). IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER iS TURNED ON. The connectors should slide together easily and snap into
p{ace. If the connectors do not slide together easily and
snap into place, turn one connector and try again. Insert
the excess Wire Harness and Pulse Wire up into the
Console Base.

-7

Press the Right and Left Top Endcaps (75, 81 ) into the
Uprights (80, 84) as shown.

5. Set the Console Base (101) on the Uprights (80, 84). Be
careful not to pinch the Wires (not shown} in the
Uprights. Attach the Console Base to each Upright with
two Console Bolts (76) and two Internal Star Washers
(77); start all four Console Bolts before tightening any of
them.

101

Make sure that the Left and Right Trays (109, 111 ) are
pressed into the Console Base (101).

6. If theWheels(notshown)aretouchingthefloor,or ifthe
treadmillrocksslightly,seeHOWTOLEVELTHE
TREADMILL
onpage20.
if youwish to adjustthe heightof the Uprights(80,
84)_gotostep7.If the Uprightsareat the desired
height_tightenthefourUprightBolts(86)andgotostep8.

7. Note:TheUprights(80,84)canbeattachedatthreedifferentheights.TheUprightsarepreattached
in themiddleposition.AdjustingtheUprightsrequirestwopersons.
Whilea secondpersonholdstheConsoleBase(101)and
theUprights(80,84),loosenthefourUprightBolts(86).
Then,removethetwoUprightBoltsandUprightStar
Washers(127)fromtheRightUpright(80).Raiseor lower
theRightUprighttothedesiredheight,beingcarefulnot
todamagetheWireHarness(74).If theUprightSpacer
(79)falls,pressit backontotheUprightBase(97).
LooselythreadthetwoUprightBoltsandUprightStar
WashersbackintotheRightUprightandtheUprightBase.

101
79

AdjusttheLeftUpright(84)inthesameway.(Note:There
arenowiresintheLeftUpright.)
Makesurethatboth
Uprightsareatthe sameheight.Lift theWamking
Platform(13)andmakesureit is centeredbetween
the Uprights.Refightenall four UprightBolts(86).
8. Makesurethatall partsareproperlytightenedbeforeyou usethe treadmill.Note:Extrahardware
may
beincluded.Keeptheincludedallenwrenchesina secureplace.Thelargeallenwrenchis usedto adjustthe
walkingbelt(seepage23).Toprotecttheflooror carpet,placea matunderthetreadmill.

if you purchasethe optionam
chestpulsesensor(see
page 20), follow the steps below to install the receiver
included with the chest pulse sensor.

107

1. Make sure that the power cord is unplugged. Remove
the indicated Screw (108) and the Access Door (122).
Wire
2. Remove the paper from the adhesive pad on the back of
the receiver (A). Orient the receiver so the small cylin=
tier is near the lower edge of the receiver and is fac=
ing the Console (107) as shown. Firmly press the re=
ceiver onto the indicated corner of the Access Door
(122). Connect the wire on the receiver to the indicated
wire extending from the Console.
3. Make sure that no wires are pinched. Reattach the
Access Door (122) with the Screw (108). Note: The wires
included with the receiver may be discarded.

OPERATION AND ADJUSTMENT
THE PERFORMANT

LUBE TM WALKING BELT

Your treadmill features a walking belt coated with
PERFORMANT LUBE TM, a high=performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking beretor the walking platform. Such substances will deteriorate the walking
belt and cause excessive wear.
HOW TO PLUG iN THE POWER CORD

of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product--if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.

Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home's power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local Sears or calt 1=800=368=7278 and order
part number 146148.
Use only a single-outlet
surge suppressor that is
UL 1449 listed as a transient voltage surge sup=
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated
for 120 volts AC and 15 amps. There must be a
monitoring light on the surge suppressor to indicate whether it is functioning properly. Failure to
use a properly functioning surge suppressor could
result in damage to the control system of the
treadmill If the control system is damaged, the
walking beJt may change speed or stop une×pectedly, which may result in afatm and serious injury.
This product must be grounded. If it should malfunc=
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec=
tric shock. This product is equipped with a cord having

an equipment=grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with aH local codes and ordinances.
Important: The treadmill
GFCFequipped outlets.

is not compatible

with

This product is for use on a nominal 120=volt circuit,
and has a grounding plug that looks like the plug illus=
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2=pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.

_Grounded
r_l

Outlet Box

II!_
_round!_entl

surge Suppressor

i:J_J.

Grounding Pin
P_
Grounding Plug

Outlet Box
Adapter

Metal Screw

The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green=colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
grounded before using an adapter.

Note:If therearethinsheetsofclear
plasticontheconsole,removethem.

Clip

FEATURES
OFTHECONSOLE

cable,youcanconnectthetreadmilltoyourhome
stereo,portablestereo,or computer
andplayspecial
Thetreadmillconsoleoffersanimpressive
arrayof
iFW.com
CDandvideoprograms
(oneiFIT.comCDis
featuresthathelpyougetthemostfromyourworkouts. included;
additional
CDsandvideocassettes
areavailableseparately),
iFIT.comCDandvideoprograms
auWhenthemanualmodeoftheconsoleis selected,
the tomatically
controlthespeedandinclineofthetreadmill
speedandinclineofthetreadmillcanbechanged
with asa personaltrainerguidesyouthrougheverystepof
thetouchofa button.Asyouexercise,theconsolewill yourworkout.High-energy
musicprovidesaddedmotidisplayinstantexercisefeedback.Youcanevenmea- vation.TopurchaseiHT.comCDsor videocassureyourheartrateusingthehandgrippulsesensoror settes,ca{Itoll-free1-800-735-0768.
theoptionalchestpulsesensor(seepage20).
Withthetreadmillconnected
toyourcomputer,
you
inaddition,theconsoleofferssixpresetworkoutprocanalsogotoourWebsiteatwwwJFIT.com
andacgrams.Eachprogramautomatically
controlsthespeed cessprogramsdirectlyfromtheinternet.Additionaloptionsaresoontobeavailable.
Seevw_,_.iF_T.com
for
andinclineofthetreadmillasitguidesyouthroughan
effective
workout.Twopulseprograms
arealsooffered. moreinformation.
Eachprogramautomatically
adjuststhespeedandinclineofthetreadmilltokeepyourheartratewithinatar- To use the manual mode of the console, follow the
getrangewhileyouexercise.
steps beginning on page 10. To use preset programs,
TheconsolealsofeaturesiFIT.cominteractive
technology.HavingiFW.com
technology
islikehavinga personaltrainerinyourhome.Usingtheincludedaudio

see page 12. To use heart rate programs, see page
13. To use an iFIT.com CD or video program, see
page 17. To use iFIT.com programs directly from
out Web site, see page 19.

buttons. Each time a

HOW TO TURN ON THE POWER

button is pressed, the
speed setting will
change by 0.1 mph; ira
button is held down, the
speed setting will
change in increments of 0.5 mph. To change
speed setting quickly, press the Quick Speed
tons. Note: The console can display speed
distance in either miles or kilometers. For

Plug in the power cord (see page 8).

ocate
the on/off
cuit
breaker
near cirthe
power cord. Make
sure that the circuit
breaker is in the on
position.

Reset
Position

plicity, nit instructions
miles.

TO USE THE MANUAL

refer to

To stop the walking belt, press the Stop button.
The Time/Pace display will begin to flash. To
restart the walking belt, press the Start button or
the Speed/' button.

tand on to
thethe
foot
of the
the drawing
treadmill.onFind
the9)clip
attached
keyrails
(see
page
and slide the clip onto the waistband of your
clothes. Next, route the cord attached to the clip
under the handgrip pulse sensor, and insert the
key into the console. After a moment, the displays
and various indicators will light. Test the clip by
carefully taking a few steps backward until the
key is pulled from the console. _fthe key is not
pulled from the console, adjust the position of
the clip.

HOW

in this section

the
butand
sim-

Note: The first time the treadmill is used, observe
the alignment of the walking belt, and align the
walking belt if necessary (see page 23).

Change the incline of the treadmill
To change the incline of
the treadmill, press the
Incline _ and/', buttons.
Each time a button is

MODE

as desired.

C,L/J
i

DIST_:_NEE

pressed, the incline will
change by 0.5%.
_1

Insert the key fully into the console.
Follow your progress
displays.

See HOW TO TURN ON THE POWER above.

F,I

Select the manuam mode.

The matri×--When the
manual mode or the
iFIT.com mode is selected, the matrix will
display a 1/4-mile track.
As you exercise, the indicators around the track

When the key is inserted, the manual
mode will be selected.
To reselect the manual
mode, press the
Program Select button
repeatedly until a track
appears in the matrix. Make sure that the indicator
on the iFF.com button is not lit.

ress the Start button or the Speed/'
start the walking belt.

with the matrix and the

will light, one at a time, until the entire track is lit.
The track will then darken and begin to light again.
Speed display--This
display shows the speed
of the walking belt. Note:
When the KM/H indicator is lit, the console will

button to

A moment after the button is pressed, the walking
belt will begin to move at 1 mph. Hold the handrails
and begin walking.

spE_= M_.

II o ....

display speed and distance in kilometers; when the KM/H indicator is
not lit, the console will display speed and distance
in miles.

As you exercise, change the speed of the walking
belt as desired by pressing the Speed _ and .,"_

To change the unit of
measurement, first hold
down the Stop button
while inserting the key
o
into the console. An "E"
for English miles or an
"M" for metric kilometers will appear in the Speed
display. Press the Speed
button to change the
unit of measurement. When the desired unit of
measurement is selected, remove the key.

You can measure your heart rate using either the
handgrip pulse sensor or the optional chest pulse
sensor.
To use the handgrip pulse sensot, first make
sure that your
hands are clean.
Next, stand on
the foot rails
and hold the

Camodes/Pulse
display--This
display
IFI _71
shows the approximate
I
t_l t-_
numbers of calories and
O F_T
Cf:qL5
fat ca/ones you have
0 _-_ULSE?
burned (see FAT BURNING on page 24). The
display will change from one number to the other
every few seconds. The display wiU also show
your heart rate when you use the handgdp pulse
sensor or the optional chest pulse sensor.
C

Distance/Incline

des-

play--Thisdisplay
shows
the distance that
you
walkedlevel
or of
and have
the incline
run

RLD

f:_IES

E31STRNCE

I /.'

handgrip pulse
sensor with your palms resting on the metal contacts. Avoid moving your hands. When your
pulse is detected, two dashes (- -) will appear in
the Calories/Pulse display, and then your heart
rate will be shown. For the most accurate heart

rate reading, continue to hold the contacts for
about 15 seconds.

]_'

Turn on the fan if desired.
To turn on the fan, press the button below the fan.
To turn on the fan at high speed, press the button
a second time. To turn off the fan, press the button a third time. Note: A few minutes after the
walking belt is stopped, the fan will automatically
turn off.

_NCLIN
...... E

the treadmill. The display
will change from one number to the other every
few seconds. Note: Each time the incline changes,
the display will show the incline setting for several
seconds.
TimetPace display-When the manual mode
or the EIT.com mode is

Measure your heart rate if desired.

When you are finished
key from the console.

exercising,

remove the

T_ME

Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when the treadmill is folded to the storage position or the treadmill will be damaged. Next, remove the key from the console and put it in a secure place. Note: If the displays and various indicators on the console remain lit after the key is
removed, the console is in the "demo" mode.
See page 20 and turn off the demo mode.

if:c,b

selected, this display will
show the elapsed time
and your current pace
(pace is measured in minutes per mile). The display wUI change from one number to the other
every few seconds. When a preset program or a
heart rate program is selected, the display will
show the time remaining in the program rather
than the elapsed time.

When you are finished using the treadmill, move
the on/off circuit breaker switch near the power
cord to the off position and unplug the power cord.

To reset the displays, press the Stop button, remove the key, and then reinsert the key.

HOWTO

The speed setting for the
Current Segment
first segment is shown in
the flashing Current
Segment column of the
matrix. (The incline set=
tings are not shown in
the matrix.) The speed
settings for the next
seven segments are
shown in the seven columns to the right.

USE PRESET PROGRAMS

_Wl Insert the key fully into the console.
See HOW TO TURN ON THE POWER on page
10.

Select one of the preset programs.
When the key
is inserted, the
manual mode
will be se=
lected. To se=
lect a preset
program,
press the Program Select button repeatedly until
one of the six preset program indicators lights.

When only three seconds remain in the first seg=
ment of the program, both the Current Segment
column and the column to the right will flash and a
series of tones will sound, in addition, if the speed
and/or incline of the treadmill is about to change,
the Speed display and/or the Distance/Incline dis=
play will flash to alert you. When the first segment
is completed, all speed settings will move one col=
umn to the left. The speed setting for the second
segment will then be shown in the flashing Current
Segment column and the treadmill will automati=
cally adjust to the speed and incline settings for
the second segment. Note: if all of the indicators in
the Current Segment column are lit after the speed
settings have moved to the left, the speed settings
will move downward so that only the highest indi=
cators appear in the matrix, if some of the indica=
tots in the Current Segment column are not lit
when the speed settings move to the left again, the
speed settings will move back up.

When a preset program is selected, the Speed
display will flash the maximum speed setting of
the program, and the Distance/Incline display will
flash the maximum incline setting, for six seconds.
The Time/Pace display will show how long the
program will last.
The matrix will show
the first seven speed
_OOOOOOOO@
settings of the program.
OOOOOOO@_
OOOOO@@@_
Note: The profiles
OOOO@@@@@
OOOOOOOOC
OOO@@@@@@
below the matrix show
OO@@@@@@@
how the speed and in=
cline of the treadmill
will change during the programs.
Press the Start button or the Speed/'
start the program.

The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column of the matrix and the
Time/Pace display counts down to zero. The walk=
ing belt will then slow to a stop.

button to

If the speed or incline setting is too high or too low
at any time during the program, you can manually
override the setting by pressing the Speed or
Incline buttons. Every few times a Speed button is
pressed, an additional indicator will light or darken
in the Current Segment column. (If any of the
columns to the right of the Current Segment col=
umn have the same number of lit indicators as the
Current Segment column, an additional indicator
may light or darken in those columns as well.)
Note: When the next segment of the program
begins, the treadmill will automatically adjust
to the speed and incline settings for the next
segment.

A moment after the button is pressed, the tread=
mill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Each program is divided into several time seg=
ments of different lengths. One speed setting and
one incline setting are programmed for each seg=
ment. Note: The same speed setting and/or in=
cline setting may be programmed for consecutive
segments.

To stop the program temporarily, press the Stop
button. The Time/Pace display wiJJbegin to flash.
To restart the program, press the Start button or
the Speed ,'_button. To end the program, press
the Stop button, remove the key, and then reinsert
the key.

HOW TO USE HEART RATE PROGRAMS

CAUTION: ifyouhave
heart
problems, or if you are over 60 years of age and
have been inactive, do not use the heart rate
programs, If you are taking medication regularly, consult your physician to find whether the
medication will affect your exercise heart rate,

Follow your progress with the displays.
See step 5 on page 10.

1_",t Measure your heart rate if desired.
Follow the steps below to use a heart rate program.
Note: You must wear the optional chest pulse sensor (see page 20) to use a heart rate program.

See step 6 on page 11.

r,,_ Turn on the fan if desired.
See step 7 on page 11.

henthe
the console.
program
from

is finished,

Put on the chest pulse sensor.
See the instructions included with the optional
chest pulse sensor.

remove the key

When the program has ended, make sure that
the incline of the treadmill is at the lowest setting. Next, remove the key from the console and
put it in a safe place. Note: Jf the displays and
various indicators on the console remain lit
after the key is removed, the console is in the
"demo" mode. Refer to page 20 and turn off the
demo mode.

insert the key fully into the console.
See HOW TO TURN ON THE POWER on page
10.
Select a heart rate program.
When the key
is inserted, the
manual mode
will be se=
lected. To se=
lect a heart

When you are finished using the treadmill, move
the on/off circuit breaker switch near the power
cord to the off position and unplug the power cord.

HEF_RT

_OATE

0"0-0

oooooo

OO@OOO

oooooo°°°°°°
En_erAge

r, _x

Speed

00_

....

rate program,
press the Program Select button repeatedly until
one of the two heart rate program indicators lights.
The two profiles on the left side of the matrix show
how the target heart rate will change during the
programs. During heart rate program 1, your heart
rate will reach approximately 85% of your esti=
mated maximum heart rate; during heart rate pro=
gram 2, your heart rate will reach approximately
80% of your estimated maximum heart rate.
Note: Your estimated maximum heart rate is de=
termined by subtracting your age from 220. For
example, if you are 30 years old, your estimated
maximum heart rate is 190 beats per minute
(220 = 30 = 190).

During heart rate programs, the matrix will
show a graphic that
represents your heart
rate. Each time a heartbeat is detected, an additional peak will appear.

automatically increase or decrease to bring your
heart rate closer to the target heart rate. If the
speed reaches the maximum speed setting of the
program (see step 4 at the left) and your heart
rate is still too far below the current target heart
rate, the incline of the treadmill will also increase
to bring your heart rate closer to the target heart
rate.

Enter your age and a maximum

speed setting.

During the last three seconds of each segment, a
series of tones will sound and the Speed display
and the Distance/Incline display will flash.

When a heart rate program is selected, the
word "AGE" and the
current age setting will
flash in the Calories/

F_T

The program wiJJcontinue until no time remains in
the program. The walking belt will then slow to a
stop.

CAL5

O F'ULSE

Pulse display, if you
have already entered
your age, simply press the Enter Age button, if
you have not entered your age, press the / and J
buttons beside the Enter Age button to enter your
age. Then, press the Enter Age button.
After you have entered
your age, the letters
"SPd" and the maxb
mum speed setting of
the program will flash in
the Calories/Pulse dis-

If the speed or incline setting is too high or too low
at any time during the program, you can adjust the
setting with the Speed or Incline buttons. However,
each time the console compares your heart rate to
the current target heart rate, the speed and/or indine of the treadmill may automatically change to
bring your heart rate closer to the target heart
rate.

......-q
O

PLJLSE

If your pulse is not detected during the program,
the letters "PLS" will flash in the Calories/
Pulse display and the speed and incline of the
treadmill may automatically decrease until your
pulse is detected. If this occurs, refer to the instructions included with the optional chest pulse sensor.

play. if desired, press
the A and
buttons beside the Enter Age button
to adjust the maximum speed setting. When the
desired setting is shown, press the Enter Age button.

I_1 Press the Start button or the Speed/'
start the program.

To stop the program at any time, press the Stop
button. Heart rate programs cannot be stopped
temporarily and then restarted. To use a heart rate
program again, reselect the program and start it at
the beginning.

button to

A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.

Each heart rate program is divided into several time
segments of different lengths. One target heart rate
is programmed for each segment.

I11

Follow your progress

with the displays.

See step 5 on page 10.
Turn on the fans if desired.
See step 7 on page 11.

During each segment, the console will regularly
compare your heart rate to the current target heart
rate. if your heart rate is too far below or above
the target heart rate, the speed of the treadmill will

When the program
from the console.

is finished,

See step 7 on page 13.

remove the key

HOW TO CONNECT YOUR PORTABLE

Note: if your stereo has an RCA-type AUDIO OUT
jack, see instruction A below, if your stereo has a
3.5ram LINE OUT jack, see instruction B. if your
stereo has only a PHONES jack, see instruction
C.

To use iFIT.com CDs, the treadmill must be connected
to your portable CD player, portable stereo, home
stereo, or computer with CD player. See pages 15 and
16 for connecting instructions. To use iFIT.com videocassettes, the treadmill must be connected to your
VCR. See page 17 for connecting instructions. To use
iFIT.com programs directly from our internet site,
the treadmill must be connected to your home com=
puter. See page 16 for connecting instructions.
HOW TO CONNECT YOUR PORTABLE

STEREO

A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter. Plug
the adapter into an AUDIO OUT jack on your stereo.

CD PLAYER
AUDIOOUT

Note: If your CD player has separate LiNE OUT and
PHONES jacks, see instruction A below. If your CD
player has only one jack, see instruction B.

L_FT

A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your CD player. Plug your headphones into the
PHONES jack.

Audo

Audio
Cable

Adapter

B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your stereo.

['@'@"

i@©,

phones
Audio

B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter (available at electronics stores). Plug the Y-adapter into
the PHONES jack on your CD player. Plug your
headphones into the other side of the Y-adapter.

C. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your stereo. Plug your
headphones into the other side of the Y-adapter.

LJ:[l

i P,0,Es
®i
u

3.5ram

.,...............,_
i[_ ("8")!
i
_ "-t i

Audio
Cable

Y-adapter

/
,................_---"'_
i_
(O')i
Audio

3.5mm
Y-adapter

Headphones --_-_
[_'

Ca211dphones

HOW TO CONNECT YOUR HOME STEREO

HOW TO CONNECT YOUR COMPUTER

Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.

Note: if your computer has a 3.5mm LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.

A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the LINE OUT jack on your
stereo.

A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your computer.
A
Ll_0Ul

i LINEOUT
Q
; ............

L.;
B
.................
@(O_

AudiOcable

Adapter_
@© Audio
Cable
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y=adapter
(available at electronics stores). Plug the Y=adapter
into the PHONES jack on your computer. Plug your
headphones or speakers into the other side of the
Y=adapter.

B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y=adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the LINE OUT jack on your
stereo and plug the wire into the unused side of the
Y=adapter. Plug the Y=adapter into the LINE OUT
jack on your stereo.

i.o
.................

CD
--

VCR

Audio

= Amply__

Cable

3. mm
_=Y-adapter

Hea dpho nes/S pea kers-_,-c:lrz3_
RCA

@©
_ [_

Audio Y-adapter
i

Cable

Adapter

Wire removed from
LINE OUT jack

HOW TO CONNECT YOUR VCR
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 16.

To use iFF.com CDs or videocassettes, the treadmill
must be connected to your portable CD player, portable
stereo, home stereo, computer with CD player, or
VCR. See HOW TO CONNECT THE TREADMILL TO
YOUR CD PLAYER, VCR, OR COMPUTER on pages
15 to 17. Note: To purchase iFIT.com CDs or video=
cassettes, call toll=free 1=800=735=0768.

A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the AUDIO OUT jack on your
VCR.

Follow the steps below to use an iFIT.com CD or video
program.

insert the key into the console.
See HOW TO TURN ON THE POWER on page 11.

.................

Ada
@©i Audio

Select the iFIT.com mode.
When the key
is inserted, the
manual mode
will be se=
lected. To use
iFIT.com CDs
or videocas=

Cable

B.......

B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y=adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the AUDIO OUT jack on your
VCR and plug the wire into the unused side of the
Y=adapter. Plug the Y=adapter into the AUDIO OUT
jack on your VCR.

settes, press the iFIT.com button. The iFF.com
indicator will light.

Insert the iFIT.com CD or videocassette.
if you are using an iFF.com CD, insert the CD
into your CD player, if you are using an iFIT.com
videocassette, insert the videocassette into your
VCR.
Press the PLAY button on your CD player or
/CR.
A moment after the button is pressed, your per=
sonal trainer will begin guiding you through your
workout. Simply follow your personal trainer's
instructions. Note: If the Time/Pace display is
flashing, press the Start button or the Speed ,_.
button on the console. The treadmill will not re=
spond to a CD or video program when the
Time/Pace display is flashing.

RCA Y-adapter-

Wire removed from-_.-E:::_J
AUDIO OUT jack

During the CD or video program, an electronic
"chirping" sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the "chirp" and be
prepared for speed and/or incline changes. In
some instances, the speed and/or incline may
change before the personal trainer describes
the change.
17

if the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next "chirp" is
heard, the speed and/or incline will change to
the next settings of the CD or video program.

Make sure that the audio cable is propeNy
connected, that it is fully plugged in, and that
it is not wrapped around a power cord.
If you are using your portable CD player and
the CD skips, set the CD player on the floor or
another flat surface instead of on the console.

To stop the walking belt at any time, press the
Stop button on the console. The Time/Pace disz
play will begin to flash. To restart the program,
press the Start button or the Speed
button. After
a moment, the walking belt will begin to move at 1
mph. When the next "chirp" is heard, the
speed and incline will change to the next settings of the CD or video program.

_"_ Follow your progress
displays.

with the track and the

See step 5 on page 10.

Measure your heart rate if desired.
See step 6 on page 11.

When the CD or video program is completed, the
walking belt will stop and the Time/Pace display
will begin to flash. Note: To use another CD or
video program, press the Stop button or remove
the key and go to step 1 on page 17.

See step 7 on page 11.
When the program
key.

Note: If the speed or incline of the treadmill
does not change when a "chirp" is heard:
Make sure that the iF_T.com indicator

Turn on the fans if desired.

is completed

remove the

See step 7 on page 13.

is lit and

that the Time/Pace dispmay is not flashing. If
the Time/Pace display is flashing, press the
Start button or the Speed/' button on the

CAUTION: Always remove iFIT.com CDs and
videocassettes from your CD player and VCR
when you are finished using them.

console.

. Adjust the volume of your CD player or VCR.
if the volume is too high or too low, the con=
sole may not detect the program signals.

Hold the handrails, step onto the walking belt, and
begin walking. During the program, an electronic
"chirping" sound will alert you when the speed
and/or inclineof the treadmill is about to change.
CAUTION: Always listen for the "chirp" and be
prepared for speed andlor incline changes.

HOW TO USE PROGRAMS DIRECTLY FROM
OUR WEB SITE

To use programs from our Web site, the treadmill must
be connected to your home computer. See HOW TO
CONNECT YOUR COMPUTER on page 16. in addition, you must have an internet connection and an internet service provider. A list of specific system requirements is found on our Web site.

if the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next "chirp" is
heard, the speed andlor incline will change to
the next settings of the program.

Follow the steps below to use a program from our
Web site.

To stop the walking belt at any time, press the
Stop button on the console. The Time/Pace display will begin to flash. To restart the program,
press the Start button or the Speed
button. After
a moment, the walking belt will begin to move at 1
mph. When the next "chirp" is heard, the speed
and incline will change to the next settings of
the program.

Insert the key into the console.
See HOW TO TURN ON THE POWER on page 10.

Select the iF_T.com mode.
When the key
is inserted, the
manual mode
will be selected. To use

When the program is completed, the walking belt
will stop and the Time/Pace display will begin to
flash. Note: To use another program, press the
Stop button and go to step 5.

a program
from our Web
site, press the iFF.com button. The iFIT.com indicator will light.

_lGo connection.
to your computer

Note: If the speed or incline of the treadmill
does not change when a "chirp" is heard, make
sure that the iFIT.com indicator is lit and that
the TimetPace display is not flashing, in addition, make sure that the audio cable is properly
connected, that it is fully plugged in, and that it
is not wrapped around a power cord.

and start an internet

ta_Web
your site
webat browser,
if necessary,
our
vvww.iFIT.com.

and go to

ollow the desired links on our Web site to select a program.

ollow your progress
displays.

with the track and the

See step 5 on page 10.
Read and follow the on-line instructionsfor using a
program.

When the program

See step 7 on page 13.

ollow the on-line instructions to start the
program.
When you start the program, an on-screen count=
down will begin.

has ended, remove the key.

Return to the treadmill and stand on the foot
pads. Find the clip attached to the key and slide
the clip onto the waistband of your clothes.
When the on-screen countdown ends, the program
will begin and the walking belt will begin to move.

THE INFORMATION

MODEIDEMO MODE

THE OPTIONAL

The console features an information mode that keeps
track of the total number of hours that the treadmill has
been operated and the total number of miles that the
walking belt has moved. The information mode also al=
lows you to switch the console from miles per hour to
kilometers per hour. In addition, the information mode
allows you to turn on and turn off the demo mode.

CHEST PULSE SENSOR

An optional chest pulse sensor adds even more
features to the console. The chest pulse sensor provides
hands-free operation and allows the console's heart
rate programs to be used. To purchase the optionaI
chest pulse sensor, catl toll-free 1-800-734-2377.

To select the information mode, hold down the Stop
button while inserting the key into the console. When
the information mode is selected, the following information will be shown:
The Distance/Incline display
will show the total number of
miles (or kilometers) that the
walking belt has moved.

HOW TO LEVEL THE TREADMILL
The Time/Pace display will
show the total number of
hours the treadmill has been
used.

T_ME

_EE

If the treadmill wheels are touching the floor or if the
treadmill rocks slightly, turn one or both of the leveling
feet under the upright base until the wheels are off the
floor and the rocking motion is eliminated. Note: If necessary, tip the treadmill and use a phillips screwdriver
to turn the leveling feet.

MIN/MILE

An "E" for English miles or
an "M" for metric kilometers
will appear in the Speed dis=
play. Press the Speed/' but=
ton to change the unit of
measurement.
IMPORTANT:

The
CALO_IE5

Calories/Pulse display
should be blank. If a "d" ap=
pears in the display, the con:
0 F_T
_AL5
sole is in the "demo" mode.
0 PULSE ©
This mode is intended to be
used only when a treadmill is
displayed in a store. When the console is in the demo
mode, the power cord can be plugged in, the key can
be removed from the console, and the displays and in:
dicators on the console will automatically light in a pre=
set sequence, although the buttons on the console will
not operate, if a "d" appears in the Calories/Pulse
display when the information mode is selected,
press the Speed V button so the display is Mank.

Feet
Levelinq
Wheels

To exit the information mode, remove the key from the
console.

HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL

FOR STORAGE

Before folding the treadmill, adjust the incline to the
lowest position, If this is not done, the treadmill may be permanently damaged, Next, unplug the power cord, CAUTION:
You must be able to safely lift 45 pounds (20 kg) in order to
raise, lower, or move the treadmill
1. Hold the treadmill with your hands in the locations shown at the
right. To decrease the possibility of injury, bend your legs
and keep your back straight. As you raise the treadmill,
make sure to lift with your legs rather than your back.
Raise the treadmill about halfway to the vertical position.

2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob to
the left and hold it. Raise the treadmill until the frame is past
the latch pin. Slowly release the latch knob. Make sure that
the frame is securely held by the latch pin.
To protect the floor or carpet from damage, place a mat
under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in
temperatures above 85 ° Fahrenheit.

Engaged
Frame

Knob
Latch Pin -/

HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage
position as described above. Make sure that the frame is securely held by the latch pin.
1. Hold the upper ends of the handrails. Place one foot on the
base as shown.
2. Tilt the treadmill back until it roils freely on the front wheels.
Carefully move the treadmill to the desired location. To reduce the risk of injury, use extreme caution while moving the treadmiml. Do not move the treadmilJ over an uneven surface.
3. Place one foot on the base, and carefully lower the treadmill
until it is resting in the storage position.
HOW TO LOWER THE TREADMILL

•Front Wheels

FOR USE

1. See drawing 2 above. Hold the upper end of the treadmill with your right hand. Pull the latch knob to the left
and hold it. Pivot the treadmill down until the frame is past the latch pin.
2. See drawing 1 above. Hold the treadmill firmly with both hands, and lower the treadmill to the floor.
CAUTION: To decrease the possibility of injury, bend your legs and keep your back straight.

Most treadmill problems can be solved by following the simple steps below. Find the symptom that
applies, and follow the steps listed, if further assistance is needed, call toll=free 1 =800=4=MY=HOME_
(1 °800°469°4663).
PROBLEM:

The power does not turn on

SOLUTION:

a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge suppressor
that meets all of the specifications described on page 8. important: The treadmill is not compatible
with GFCFequipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
C.

Check the on/off circuit breaker located on the
treadmill frame near the power cord. If the switch
protrudes as shown, the on/off circuit breaker has
tripped. To reset the on/off circuit breaker, wait for
five minutes and then press the switch back in.

Tripped

Reset

PROBLEM:

The power turns off during use

SOLUTION:

a. Check the on/off circuit breaker (see the drawing above), if the on/off circuit breaker has tripped,
wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. If the treadmill still will not run, please call toIFfree 1-800-4-MY-HOME _'_
(1-800-469-4663).

PROBLEM:

The incline of the treadmill

does not change correctly

SOLUTION:

a. With the key in the console, press one of the Incline buttons. While the incline is changing, remove the key. After a few seconds, reqnsert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM:

The console

SOLUTION:

a. See assembly step 7 on page 7.

PROBLEM:

The treadmill

SOLUTION:

a. See HOW TO LEVEL THE TREADMILL on page 20.

PROBLEM:

The displays

SOLUTION:

a. Remove the key from the console and UNPLUG THE
POWER CORD. With the help of a second person,
carefully tip the Upright Base (97) down as shown.
Remove the five Hood Screws (44). Note: A phillips
screwdriver with at least a 5" shaft is required.

is too high or too low

rocks during use

of the console do not function

properly
_44

With the help of a second person, carefully raise the
Upright Base (97) as shown. Carefully pivot the Hood
(123) off.

Locate the Reed Switch (22) and the Magnet (19) on
the left side of the Pulley (18). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 118". If necessary, loosen the Screw
(23) and move the Reed Switch slightly. Retighten the
Screw. Reattach the Hood, and run the treadmill for a
few minutes to check for a correct speed reading.

PROBLEM:
SOLUTION:

The watking

belt slows when wamked on

a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 8.
b.

if the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
rear roller adjustment bolts counterclockwise, 1/4 of a
turn. When the walking belt is properly tightened, you
should be able to lift each side of the walking belt 2 to
3 inches off the walking platform. Be careful to keep
the walking belt centered. Plug in the power cord, insert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.

Rear Roller Adjustment Bolts

c. If the walking belt still slows when walked on, please call toll-free 1-800-4-MY-HOME
Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.2
Linearized : No
Page Count : 30
Page Layout : SinglePage
Page Mode : UseNone
Producer : Goby Monitor Application version 3, 2, 1, 4
Create Date : Wed Aug 15 12:13:43 2007
Author :
Title :
Subject :

EXIF Metadata provided by EXIF.tools

Proform 831293062 User Manual 580X Manuals And Guides L0704151

PROFORM Treadmill Manual L0704151 PROFORM Treadmill Owner's Manual, PROFORM Treadmill installation guides

831.293062 L0704151

Navigation menu

Versions of this User Manual:

Views

Navigation